diff options
26 files changed, 410 insertions, 57 deletions
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c index c7a032a4f0c5..d214448b677e 100644 --- a/drivers/usb/chipidea/udc.c +++ b/drivers/usb/chipidea/udc.c @@ -78,8 +78,7 @@ static inline int ep_to_bit(struct ci13xxx *ci, int n) } /** - * hw_device_state: enables/disables interrupts & starts/stops device (execute - * without interruption) + * hw_device_state: enables/disables interrupts (execute without interruption) * @dma: 0 => disable, !0 => enable and set dma engine * * This function returns an error code @@ -91,9 +90,7 @@ static int hw_device_state(struct ci13xxx *ci, u32 dma) /* interrupt, error, port change, reset, sleep/suspend */ hw_write(ci, OP_USBINTR, ~0, USBi_UI|USBi_UEI|USBi_PCI|USBi_URI|USBi_SLI); - hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS); } else { - hw_write(ci, OP_USBCMD, USBCMD_RS, 0); hw_write(ci, OP_USBINTR, ~0, 0); } return 0; @@ -774,10 +771,7 @@ __acquires(mEp->lock) { struct ci13xxx_req *mReq, *mReqTemp; struct ci13xxx_ep *mEpTemp = mEp; - int uninitialized_var(retval); - - if (list_empty(&mEp->qh.queue)) - return -EINVAL; + int retval = 0; list_for_each_entry_safe(mReq, mReqTemp, &mEp->qh.queue, queue) { @@ -1420,6 +1414,21 @@ static int ci13xxx_vbus_draw(struct usb_gadget *_gadget, unsigned mA) return -ENOTSUPP; } +/* Change Data+ pullup status + * this func is used by usb_gadget_connect/disconnet + */ +static int ci13xxx_pullup(struct usb_gadget *_gadget, int is_on) +{ + struct ci13xxx *ci = container_of(_gadget, struct ci13xxx, gadget); + + if (is_on) + hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS); + else + hw_write(ci, OP_USBCMD, USBCMD_RS, 0); + + return 0; +} + static int ci13xxx_start(struct usb_gadget *gadget, struct usb_gadget_driver *driver); static int ci13xxx_stop(struct usb_gadget *gadget, @@ -1432,6 +1441,7 @@ static int ci13xxx_stop(struct usb_gadget *gadget, static const struct usb_gadget_ops usb_gadget_ops = { .vbus_session = ci13xxx_vbus_session, .wakeup = ci13xxx_wakeup, + .pullup = ci13xxx_pullup, .vbus_draw = ci13xxx_vbus_draw, .udc_start = ci13xxx_start, .udc_stop = ci13xxx_stop, @@ -1455,7 +1465,12 @@ static int init_eps(struct ci13xxx *ci) mEp->ep.name = mEp->name; mEp->ep.ops = &usb_ep_ops; - mEp->ep.maxpacket = CTRL_PAYLOAD_MAX; + /* + * for ep0: maxP defined in desc, for other + * eps, maxP is set by epautoconfig() called + * by gadget layer + */ + mEp->ep.maxpacket = (unsigned short)~0; INIT_LIST_HEAD(&mEp->qh.queue); mEp->qh.ptr = dma_pool_alloc(ci->qh_pool, GFP_KERNEL, @@ -1475,6 +1490,7 @@ static int init_eps(struct ci13xxx *ci) else ci->ep0in = mEp; + mEp->ep.maxpacket = CTRL_PAYLOAD_MAX; continue; } @@ -1484,6 +1500,17 @@ static int init_eps(struct ci13xxx *ci) return retval; } +static void destroy_eps(struct ci13xxx *ci) +{ + int i; + + for (i = 0; i < ci->hw_ep_max; i++) { + struct ci13xxx_ep *mEp = &ci->ci13xxx_ep[i]; + + dma_pool_free(ci->qh_pool, mEp->qh.ptr, mEp->qh.dma); + } +} + /** * ci13xxx_start: register a gadget driver * @gadget: our gadget @@ -1691,7 +1718,7 @@ static int udc_start(struct ci13xxx *ci) if (ci->platdata->flags & CI13XXX_REQUIRE_TRANSCEIVER) { if (ci->transceiver == NULL) { retval = -ENODEV; - goto free_pools; + goto destroy_eps; } } @@ -1729,7 +1756,7 @@ static int udc_start(struct ci13xxx *ci) remove_trans: if (!IS_ERR_OR_NULL(ci->transceiver)) { - otg_set_peripheral(ci->transceiver->otg, &ci->gadget); + otg_set_peripheral(ci->transceiver->otg, NULL); if (ci->global_phy) usb_put_phy(ci->transceiver); } @@ -1742,6 +1769,8 @@ unreg_device: put_transceiver: if (!IS_ERR_OR_NULL(ci->transceiver) && ci->global_phy) usb_put_phy(ci->transceiver); +destroy_eps: + destroy_eps(ci); free_pools: dma_pool_destroy(ci->td_pool); free_qh_pool: @@ -1756,18 +1785,12 @@ free_qh_pool: */ static void udc_stop(struct ci13xxx *ci) { - int i; - if (ci == NULL) return; usb_del_gadget_udc(&ci->gadget); - for (i = 0; i < ci->hw_ep_max; i++) { - struct ci13xxx_ep *mEp = &ci->ci13xxx_ep[i]; - - dma_pool_free(ci->qh_pool, mEp->qh.ptr, mEp->qh.dma); - } + destroy_eps(ci); dma_pool_destroy(ci->td_pool); dma_pool_destroy(ci->qh_pool); diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c index 65a55abb791f..5f0cb417b736 100644 --- a/drivers/usb/class/cdc-wdm.c +++ b/drivers/usb/class/cdc-wdm.c @@ -109,12 +109,14 @@ static struct usb_driver wdm_driver; /* return intfdata if we own the interface, else look up intf in the list */ static struct wdm_device *wdm_find_device(struct usb_interface *intf) { - struct wdm_device *desc = NULL; + struct wdm_device *desc; spin_lock(&wdm_device_list_lock); list_for_each_entry(desc, &wdm_device_list, device_list) if (desc->intf == intf) - break; + goto found; + desc = NULL; +found: spin_unlock(&wdm_device_list_lock); return desc; @@ -122,12 +124,14 @@ static struct wdm_device *wdm_find_device(struct usb_interface *intf) static struct wdm_device *wdm_find_device_by_minor(int minor) { - struct wdm_device *desc = NULL; + struct wdm_device *desc; spin_lock(&wdm_device_list_lock); list_for_each_entry(desc, &wdm_device_list, device_list) if (desc->intf->minor == minor) - break; + goto found; + desc = NULL; +found: spin_unlock(&wdm_device_list_lock); return desc; diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index f15501f4c585..e77a8e8eaa23 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -71,6 +71,10 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x04b4, 0x0526), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS }, + /* Microchip Joss Optical infrared touchboard device */ + { USB_DEVICE(0x04d8, 0x000c), .driver_info = + USB_QUIRK_CONFIG_INTF_STRINGS }, + /* Samsung Android phone modem - ID conflict with SPH-I500 */ { USB_DEVICE(0x04e8, 0x6601), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS }, diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index c34452a7304f..a68ff53124dc 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -436,16 +436,21 @@ static int __devinit dwc3_probe(struct platform_device *pdev) dev_err(dev, "missing IRQ\n"); return -ENODEV; } - dwc->xhci_resources[1] = *res; + dwc->xhci_resources[1].start = res->start; + dwc->xhci_resources[1].end = res->end; + dwc->xhci_resources[1].flags = res->flags; + dwc->xhci_resources[1].name = res->name; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res) { dev_err(dev, "missing memory resource\n"); return -ENODEV; } - dwc->xhci_resources[0] = *res; + dwc->xhci_resources[0].start = res->start; dwc->xhci_resources[0].end = dwc->xhci_resources[0].start + DWC3_XHCI_REGS_END; + dwc->xhci_resources[0].flags = res->flags; + dwc->xhci_resources[0].name = res->name; /* * Request memory region but exclude xHCI regs, diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c index 9b94886b66e5..e4d5ca86b9da 100644 --- a/drivers/usb/dwc3/ep0.c +++ b/drivers/usb/dwc3/ep0.c @@ -720,7 +720,6 @@ static void dwc3_ep0_complete_data(struct dwc3 *dwc, transferred = min_t(u32, ur->length, transfer_size - length); memcpy(ur->buf, dwc->ep0_bounce, transferred); - dwc->ep0_bounced = false; } else { transferred = ur->length - length; } diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 58fdfad96b4d..c2813c2b005a 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -263,8 +263,11 @@ void dwc3_gadget_giveback(struct dwc3_ep *dep, struct dwc3_request *req, if (req->request.status == -EINPROGRESS) req->request.status = status; - usb_gadget_unmap_request(&dwc->gadget, &req->request, - req->direction); + if (dwc->ep0_bounced && dep->number == 0) + dwc->ep0_bounced = false; + else + usb_gadget_unmap_request(&dwc->gadget, &req->request, + req->direction); dev_dbg(dwc->dev, "request %p from %s completed %d/%d ===> %d\n", req, dep->name, req->request.actual, @@ -1026,6 +1029,7 @@ static void __dwc3_gadget_start_isoc(struct dwc3 *dwc, if (list_empty(&dep->request_list)) { dev_vdbg(dwc->dev, "ISOC ep %s run out for requests.\n", dep->name); + dep->flags |= DWC3_EP_PENDING_REQUEST; return; } @@ -1089,6 +1093,17 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req) if (dep->flags & DWC3_EP_PENDING_REQUEST) { int ret; + /* + * If xfernotready is already elapsed and it is a case + * of isoc transfer, then issue END TRANSFER, so that + * you can receive xfernotready again and can have + * notion of current microframe. + */ + if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) { + dwc3_stop_active_transfer(dwc, dep->number); + return 0; + } + ret = __dwc3_gadget_kick_transfer(dep, 0, true); if (ret && ret != -EBUSY) { struct dwc3 *dwc = dep->dwc; diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index c9e66dfb02e6..1e35963bd4ed 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -475,8 +475,7 @@ static int at91_ep_enable(struct usb_ep *_ep, unsigned long flags; if (!_ep || !ep - || !desc || ep->ep.desc - || _ep->name == ep0name + || !desc || _ep->name == ep0name || desc->bDescriptorType != USB_DT_ENDPOINT || (maxpacket = usb_endpoint_maxp(desc)) == 0 || maxpacket > ep->maxpacket) { @@ -530,7 +529,6 @@ ok: tmp |= AT91_UDP_EPEDS; __raw_writel(tmp, ep->creg); - ep->ep.desc = desc; ep->ep.maxpacket = maxpacket; /* @@ -1635,7 +1633,6 @@ static int at91_start(struct usb_gadget *gadget, udc->driver = driver; udc->gadget.dev.driver = &driver->driver; udc->gadget.dev.of_node = udc->pdev->dev.of_node; - dev_set_drvdata(&udc->gadget.dev, &driver->driver); udc->enabled = 1; udc->selfpowered = 1; @@ -1656,7 +1653,6 @@ static int at91_stop(struct usb_gadget *gadget, spin_unlock_irqrestore(&udc->lock, flags); udc->gadget.dev.driver = NULL; - dev_set_drvdata(&udc->gadget.dev, NULL); udc->driver = NULL; DBG("unbound from %s\n", driver->driver.name); diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c index b799106027ad..afdbb1cbf5d9 100644 --- a/drivers/usb/gadget/dummy_hcd.c +++ b/drivers/usb/gadget/dummy_hcd.c @@ -1916,6 +1916,27 @@ done: return retval; } +/* usb 3.0 root hub device descriptor */ +struct { + struct usb_bos_descriptor bos; + struct usb_ss_cap_descriptor ss_cap; +} __packed usb3_bos_desc = { + + .bos = { + .bLength = USB_DT_BOS_SIZE, + .bDescriptorType = USB_DT_BOS, + .wTotalLength = cpu_to_le16(sizeof(usb3_bos_desc)), + .bNumDeviceCaps = 1, + }, + .ss_cap = { + .bLength = USB_DT_USB_SS_CAP_SIZE, + .bDescriptorType = USB_DT_DEVICE_CAPABILITY, + .bDevCapabilityType = USB_SS_CAP_TYPE, + .wSpeedSupported = cpu_to_le16(USB_5GBPS_OPERATION), + .bFunctionalitySupport = ilog2(USB_5GBPS_OPERATION), + }, +}; + static inline void ss_hub_descriptor(struct usb_hub_descriptor *desc) { @@ -2006,6 +2027,18 @@ static int dummy_hub_control( else hub_descriptor((struct usb_hub_descriptor *) buf); break; + + case DeviceRequest | USB_REQ_GET_DESCRIPTOR: + if (hcd->speed != HCD_USB3) + goto error; + + if ((wValue >> 8) != USB_DT_BOS) + goto error; + + memcpy(buf, &usb3_bos_desc, sizeof(usb3_bos_desc)); + retval = sizeof(usb3_bos_desc); + break; + case GetHubStatus: *(__le32 *) buf = cpu_to_le32(0); break; @@ -2503,10 +2536,8 @@ static int dummy_hcd_probe(struct platform_device *pdev) hs_hcd->has_tt = 1; retval = usb_add_hcd(hs_hcd, 0, 0); - if (retval != 0) { - usb_put_hcd(hs_hcd); - return retval; - } + if (retval) + goto put_usb2_hcd; if (mod_data.is_super_speed) { ss_hcd = usb_create_shared_hcd(&dummy_hcd, &pdev->dev, @@ -2525,6 +2556,8 @@ static int dummy_hcd_probe(struct platform_device *pdev) put_usb3_hcd: usb_put_hcd(ss_hcd); dealloc_usb2_hcd: + usb_remove_hcd(hs_hcd); +put_usb2_hcd: usb_put_hcd(hs_hcd); the_controller.hs_hcd = the_controller.ss_hcd = NULL; return retval; diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c index 8adc79d1b402..829aba75a6df 100644 --- a/drivers/usb/gadget/f_fs.c +++ b/drivers/usb/gadget/f_fs.c @@ -34,11 +34,15 @@ /* Debugging ****************************************************************/ #ifdef VERBOSE_DEBUG +#ifndef pr_vdebug # define pr_vdebug pr_debug +#endif /* pr_vdebug */ # define ffs_dump_mem(prefix, ptr, len) \ print_hex_dump_bytes(pr_fmt(prefix ": "), DUMP_PREFIX_NONE, ptr, len) #else +#ifndef pr_vdebug # define pr_vdebug(...) do { } while (0) +#endif /* pr_vdebug */ # define ffs_dump_mem(prefix, ptr, len) do { } while (0) #endif /* VERBOSE_DEBUG */ diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c index b13e0bb5f5b8..0bb617e1dda2 100644 --- a/drivers/usb/gadget/s3c-hsotg.c +++ b/drivers/usb/gadget/s3c-hsotg.c @@ -3599,6 +3599,7 @@ static int __devinit s3c_hsotg_probe(struct platform_device *pdev) if (hsotg->num_of_eps == 0) { dev_err(dev, "wrong number of EPs (zero)\n"); + ret = -EINVAL; goto err_supplies; } @@ -3606,6 +3607,7 @@ static int __devinit s3c_hsotg_probe(struct platform_device *pdev) GFP_KERNEL); if (!eps) { dev_err(dev, "cannot get memory\n"); + ret = -ENOMEM; goto err_supplies; } @@ -3622,6 +3624,7 @@ static int __devinit s3c_hsotg_probe(struct platform_device *pdev) GFP_KERNEL); if (!hsotg->ctrl_req) { dev_err(dev, "failed to allocate ctrl req\n"); + ret = -ENOMEM; goto err_ep_mem; } diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c index 5b3f5fffea92..da6d479ff9a6 100644 --- a/drivers/usb/gadget/u_serial.c +++ b/drivers/usb/gadget/u_serial.c @@ -132,11 +132,15 @@ static unsigned n_ports; #ifdef VERBOSE_DEBUG +#ifndef pr_vdebug #define pr_vdebug(fmt, arg...) \ pr_debug(fmt, ##arg) +#endif /* pr_vdebug */ #else +#ifndef pr_vdebig #define pr_vdebug(fmt, arg...) \ ({ if (0) pr_debug(fmt, ##arg); }) +#endif /* pr_vdebug */ #endif /*-------------------------------------------------------------------------*/ diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index 9bc39ca460c8..4b66374bdc8e 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -128,9 +128,17 @@ qh_refresh (struct ehci_hcd *ehci, struct ehci_qh *qh) else { qtd = list_entry (qh->qtd_list.next, struct ehci_qtd, qtd_list); - /* first qtd may already be partially processed */ - if (cpu_to_hc32(ehci, qtd->qtd_dma) == qh->hw->hw_current) + /* + * first qtd may already be partially processed. + * If we come here during unlink, the QH overlay region + * might have reference to the just unlinked qtd. The + * qtd is updated in qh_completions(). Update the QH + * overlay here. + */ + if (cpu_to_hc32(ehci, qtd->qtd_dma) == qh->hw->hw_current) { + qh->hw->hw_qtd_next = qtd->hw_next; qtd = NULL; + } } if (qtd) diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index a665b3eaa746..aaa8d2bce217 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -570,6 +570,16 @@ static int __devinit ohci_hcd_at91_drv_probe(struct platform_device *pdev) if (pdata) { at91_for_each_port(i) { + /* + * do not configure PIO if not in relation with + * real USB port on board + */ + if (i >= pdata->ports) { + pdata->vbus_pin[i] = -EINVAL; + pdata->overcurrent_pin[i] = -EINVAL; + break; + } + if (!gpio_is_valid(pdata->vbus_pin[i])) continue; gpio = pdata->vbus_pin[i]; diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index c5e9e4a76f14..966d1484ee79 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -75,7 +75,9 @@ #define NB_PIF0_PWRDOWN_1 0x01100013 #define USB_INTEL_XUSB2PR 0xD0 +#define USB_INTEL_USB2PRM 0xD4 #define USB_INTEL_USB3_PSSEN 0xD8 +#define USB_INTEL_USB3PRM 0xDC static struct amd_chipset_info { struct pci_dev *nb_dev; @@ -772,10 +774,18 @@ void usb_enable_xhci_ports(struct pci_dev *xhci_pdev) return; } - ports_available = 0xffffffff; + /* Read USB3PRM, the USB 3.0 Port Routing Mask Register + * Indicate the ports that can be changed from OS. + */ + pci_read_config_dword(xhci_pdev, USB_INTEL_USB3PRM, + &ports_available); + + dev_dbg(&xhci_pdev->dev, "Configurable ports to enable SuperSpeed: 0x%x\n", + ports_available); + /* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable - * Register, to turn on SuperSpeed terminations for all - * available ports. + * Register, to turn on SuperSpeed terminations for the + * switchable ports. */ pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, cpu_to_le32(ports_available)); @@ -785,7 +795,16 @@ void usb_enable_xhci_ports(struct pci_dev *xhci_pdev) dev_dbg(&xhci_pdev->dev, "USB 3.0 ports that are now enabled " "under xHCI: 0x%x\n", ports_available); - ports_available = 0xffffffff; + /* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register + * Indicate the USB 2.0 ports to be controlled by the xHCI host. + */ + + pci_read_config_dword(xhci_pdev, USB_INTEL_USB2PRM, + &ports_available); + + dev_dbg(&xhci_pdev->dev, "Configurable USB 2.0 ports to hand over to xCHI: 0x%x\n", + ports_available); + /* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to * switch the USB 2.0 power and data lines over to the xHCI * host. @@ -822,12 +841,12 @@ static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) void __iomem *op_reg_base; u32 val; int timeout; + int len = pci_resource_len(pdev, 0); if (!mmio_resource_enabled(pdev, 0)) return; - base = ioremap_nocache(pci_resource_start(pdev, 0), - pci_resource_len(pdev, 0)); + base = ioremap_nocache(pci_resource_start(pdev, 0), len); if (base == NULL) return; @@ -837,9 +856,17 @@ static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) */ ext_cap_offset = xhci_find_next_cap_offset(base, XHCI_HCC_PARAMS_OFFSET); do { + if ((ext_cap_offset + sizeof(val)) > len) { + /* We're reading garbage from the controller */ + dev_warn(&pdev->dev, + "xHCI controller failing to respond"); + return; + } + if (!ext_cap_offset) /* We've reached the end of the extended capabilities */ goto hc_init; + val = readl(base + ext_cap_offset); if (XHCI_EXT_CAPS_ID(val) == XHCI_EXT_CAPS_LEGACY) break; @@ -870,9 +897,10 @@ static void __devinit quirk_usb_handoff_xhci(struct pci_dev *pdev) /* Disable any BIOS SMIs and clear all SMI events*/ writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET); +hc_init: if (usb_is_intel_switchable_xhci(pdev)) usb_enable_xhci_ports(pdev); -hc_init: + op_reg_base = base + XHCI_HC_LENGTH(readl(base)); /* Wait for the host controller to be ready before writing any diff --git a/drivers/usb/host/pci-quirks.h b/drivers/usb/host/pci-quirks.h index ef004a5de20f..7f69a39163ce 100644 --- a/drivers/usb/host/pci-quirks.h +++ b/drivers/usb/host/pci-quirks.h @@ -15,6 +15,7 @@ void usb_disable_xhci_ports(struct pci_dev *xhci_pdev); static inline void usb_amd_quirk_pll_disable(void) {} static inline void usb_amd_quirk_pll_enable(void) {} static inline void usb_amd_dev_put(void) {} +static inline void usb_disable_xhci_ports(struct pci_dev *xhci_pdev) {} #endif /* CONFIG_PCI */ #endif /* __LINUX_USB_PCI_QUIRKS_H */ diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index 74bfc868b7ad..d5eb357aa5c4 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -493,11 +493,48 @@ static void xhci_hub_report_link_state(u32 *status, u32 status_reg) * when this bit is set. */ pls |= USB_PORT_STAT_CONNECTION; + } else { + /* + * If CAS bit isn't set but the Port is already at + * Compliance Mode, fake a connection so the USB core + * notices the Compliance state and resets the port. + * This resolves an issue generated by the SN65LVPE502CP + * in which sometimes the port enters compliance mode + * caused by a delay on the host-device negotiation. + */ + if (pls == USB_SS_PORT_LS_COMP_MOD) + pls |= USB_PORT_STAT_CONNECTION; } + /* update status field */ *status |= pls; } +/* + * Function for Compliance Mode Quirk. + * + * This Function verifies if all xhc USB3 ports have entered U0, if so, + * the compliance mode timer is deleted. A port won't enter + * compliance mode if it has previously entered U0. + */ +void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status, u16 wIndex) +{ + u32 all_ports_seen_u0 = ((1 << xhci->num_usb3_ports)-1); + bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0); + + if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK)) + return; + + if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) { + xhci->port_status_u0 |= 1 << wIndex; + if (xhci->port_status_u0 == all_ports_seen_u0) { + del_timer_sync(&xhci->comp_mode_recovery_timer); + xhci_dbg(xhci, "All USB3 ports have entered U0 already!\n"); + xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted.\n"); + } + } +} + int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength) { @@ -651,6 +688,11 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, /* Update Port Link State for super speed ports*/ if (hcd->speed == HCD_USB3) { xhci_hub_report_link_state(&status, temp); + /* + * Verify if all USB3 Ports Have entered U0 already. + * Delete Compliance Mode Timer if so. + */ + xhci_del_comp_mod_timer(xhci, temp, wIndex); } if (bus_state->port_c_suspend & (1 << wIndex)) status |= 1 << USB_PORT_FEAT_C_SUSPEND; diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c index 689bc18b051d..df90fe51b4aa 100644 --- a/drivers/usb/host/xhci-plat.c +++ b/drivers/usb/host/xhci-plat.c @@ -118,7 +118,7 @@ static int xhci_plat_probe(struct platform_device *pdev) goto put_hcd; } - hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len); if (!hcd->regs) { dev_dbg(&pdev->dev, "error mapping memory\n"); ret = -EFAULT; diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index c59d5b5b6c7d..6ece0ed288d4 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -26,6 +26,7 @@ #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/slab.h> +#include <linux/dmi.h> #include "xhci.h" @@ -398,6 +399,95 @@ static void xhci_msix_sync_irqs(struct xhci_hcd *xhci) #endif +static void compliance_mode_recovery(unsigned long arg) +{ + struct xhci_hcd *xhci; + struct usb_hcd *hcd; + u32 temp; + int i; + + xhci = (struct xhci_hcd *)arg; + + for (i = 0; i < xhci->num_usb3_ports; i++) { + temp = xhci_readl(xhci, xhci->usb3_ports[i]); + if ((temp & PORT_PLS_MASK) == USB_SS_PORT_LS_COMP_MOD) { + /* + * Compliance Mode Detected. Letting USB Core + * handle the Warm Reset + */ + xhci_dbg(xhci, "Compliance Mode Detected->Port %d!\n", + i + 1); + xhci_dbg(xhci, "Attempting Recovery routine!\n"); + hcd = xhci->shared_hcd; + + if (hcd->state == HC_STATE_SUSPENDED) + usb_hcd_resume_root_hub(hcd); + + usb_hcd_poll_rh_status(hcd); + } + } + + if (xhci->port_status_u0 != ((1 << xhci->num_usb3_ports)-1)) + mod_timer(&xhci->comp_mode_recovery_timer, + jiffies + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS)); +} + +/* + * Quirk to work around issue generated by the SN65LVPE502CP USB3.0 re-driver + * that causes ports behind that hardware to enter compliance mode sometimes. + * The quirk creates a timer that polls every 2 seconds the link state of + * each host controller's port and recovers it by issuing a Warm reset + * if Compliance mode is detected, otherwise the port will become "dead" (no + * device connections or disconnections will be detected anymore). Becasue no + * status event is generated when entering compliance mode (per xhci spec), + * this quirk is needed on systems that have the failing hardware installed. + */ +static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci) +{ + xhci->port_status_u0 = 0; + init_timer(&xhci->comp_mode_recovery_timer); + + xhci->comp_mode_recovery_timer.data = (unsigned long) xhci; + xhci->comp_mode_recovery_timer.function = compliance_mode_recovery; + xhci->comp_mode_recovery_timer.expires = jiffies + + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS); + + set_timer_slack(&xhci->comp_mode_recovery_timer, + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS)); + add_timer(&xhci->comp_mode_recovery_timer); + xhci_dbg(xhci, "Compliance Mode Recovery Timer Initialized.\n"); +} + +/* + * This function identifies the systems that have installed the SN65LVPE502CP + * USB3.0 re-driver and that need the Compliance Mode Quirk. + * Systems: + * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820 + */ +static bool compliance_mode_recovery_timer_quirk_check(void) +{ + const char *dmi_product_name, *dmi_sys_vendor; + + dmi_product_name = dmi_get_system_info(DMI_PRODUCT_NAME); + dmi_sys_vendor = dmi_get_system_info(DMI_SYS_VENDOR); + + if (!(strstr(dmi_sys_vendor, "Hewlett-Packard"))) + return false; + + if (strstr(dmi_product_name, "Z420") || + strstr(dmi_product_name, "Z620") || + strstr(dmi_product_name, "Z820")) + return true; + + return false; +} + +static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci) +{ + return (xhci->port_status_u0 == ((1 << xhci->num_usb3_ports)-1)); +} + + /* * Initialize memory for HCD and xHC (one-time init). * @@ -421,6 +511,12 @@ int xhci_init(struct usb_hcd *hcd) retval = xhci_mem_init(xhci, GFP_KERNEL); xhci_dbg(xhci, "Finished xhci_init\n"); + /* Initializing Compliance Mode Recovery Data If Needed */ + if (compliance_mode_recovery_timer_quirk_check()) { + xhci->quirks |= XHCI_COMP_MODE_QUIRK; + compliance_mode_recovery_timer_init(xhci); + } + return retval; } @@ -629,6 +725,11 @@ void xhci_stop(struct usb_hcd *hcd) del_timer_sync(&xhci->event_ring_timer); #endif + /* Deleting Compliance Mode Recovery Timer */ + if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && + (!(xhci_all_ports_seen_u0(xhci)))) + del_timer_sync(&xhci->comp_mode_recovery_timer); + if (xhci->quirks & XHCI_AMD_PLL_FIX) usb_amd_dev_put(); @@ -659,7 +760,7 @@ void xhci_shutdown(struct usb_hcd *hcd) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); - if (xhci->quirks && XHCI_SPURIOUS_REBOOT) + if (xhci->quirks & XHCI_SPURIOUS_REBOOT) usb_disable_xhci_ports(to_pci_dev(hcd->self.controller)); spin_lock_irq(&xhci->lock); @@ -806,6 +907,16 @@ int xhci_suspend(struct xhci_hcd *xhci) } spin_unlock_irq(&xhci->lock); + /* + * Deleting Compliance Mode Recovery Timer because the xHCI Host + * is about to be suspended. + */ + if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && + (!(xhci_all_ports_seen_u0(xhci)))) { + del_timer_sync(&xhci->comp_mode_recovery_timer); + xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted!\n"); + } + /* step 5: remove core well power */ /* synchronize irq when using MSI-X */ xhci_msix_sync_irqs(xhci); @@ -938,6 +1049,16 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) usb_hcd_resume_root_hub(hcd); usb_hcd_resume_root_hub(xhci->shared_hcd); } + + /* + * If system is subject to the Quirk, Compliance Mode Timer needs to + * be re-initialized Always after a system resume. Ports are subject + * to suffer the Compliance Mode issue again. It doesn't matter if + * ports have entered previously to U0 before system's suspension. + */ + if (xhci->quirks & XHCI_COMP_MODE_QUIRK) + compliance_mode_recovery_timer_init(xhci); + return retval; } #endif /* CONFIG_PM */ diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index c713256297ac..1a05908c6673 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1495,6 +1495,7 @@ struct xhci_hcd { #define XHCI_LPM_SUPPORT (1 << 11) #define XHCI_INTEL_HOST (1 << 12) #define XHCI_SPURIOUS_REBOOT (1 << 13) +#define XHCI_COMP_MODE_QUIRK (1 << 14) unsigned int num_active_eps; unsigned int limit_active_eps; /* There are two roothubs to keep track of bus suspend info for */ @@ -1511,6 +1512,11 @@ struct xhci_hcd { unsigned sw_lpm_support:1; /* support xHCI 1.0 spec USB2 hardware LPM */ unsigned hw_lpm_support:1; + /* Compliance Mode Recovery Data */ + struct timer_list comp_mode_recovery_timer; + u32 port_status_u0; +/* Compliance Mode Timer Triggered every 2 seconds */ +#define COMP_MODE_RCVRY_MSECS 2000 }; /* convert between an HCD pointer and the corresponding EHCI_HCD */ diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c index 4bb717d0bd41..1ae378d5fc6f 100644 --- a/drivers/usb/musb/musb_host.c +++ b/drivers/usb/musb/musb_host.c @@ -2049,7 +2049,7 @@ static int musb_urb_enqueue( * we only have work to do in the former case. */ spin_lock_irqsave(&musb->lock, flags); - if (hep->hcpriv) { + if (hep->hcpriv || !next_urb(qh)) { /* some concurrent activity submitted another urb to hep... * odd, rare, error prone, but legal. */ diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c index 57a608584e16..c1be687e00ec 100644 --- a/drivers/usb/musb/musbhsdma.c +++ b/drivers/usb/musb/musbhsdma.c @@ -388,7 +388,7 @@ dma_controller_create(struct musb *musb, void __iomem *base) struct platform_device *pdev = to_platform_device(dev); int irq = platform_get_irq_byname(pdev, "dma"); - if (irq == 0) { + if (irq <= 0) { dev_err(dev, "No DMA interrupt line!\n"); return NULL; } diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index 1a1bd9cf40c5..341625442377 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -1215,7 +1215,7 @@ static int __devinit tusb_probe(struct platform_device *pdev) ret = platform_device_add(musb); if (ret) { dev_err(&pdev->dev, "failed to register musb device\n"); - goto err1; + goto err2; } return 0; diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c index ecd173032fd4..143c4e9e1be4 100644 --- a/drivers/usb/renesas_usbhs/fifo.c +++ b/drivers/usb/renesas_usbhs/fifo.c @@ -818,7 +818,7 @@ static int usbhsf_dma_prepare_push(struct usbhs_pkt *pkt, int *is_done) usbhs_pipe_is_dcp(pipe)) goto usbhsf_pio_prepare_push; - if (len % 4) /* 32bit alignment */ + if (len & 0x7) /* 8byte alignment */ goto usbhsf_pio_prepare_push; if ((uintptr_t)(pkt->buf + pkt->actual) & 0x7) /* 8byte alignment */ @@ -905,7 +905,7 @@ static int usbhsf_dma_try_pop(struct usbhs_pkt *pkt, int *is_done) /* use PIO if packet is less than pio_dma_border */ len = usbhsf_fifo_rcv_len(priv, fifo); len = min(pkt->length - pkt->actual, len); - if (len % 4) /* 32bit alignment */ + if (len & 0x7) /* 8byte alignment */ goto usbhsf_pio_prepare_pop_unselect; if (len < usbhs_get_dparam(priv, pio_dma_border)) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 5620db6469e5..f906b3aec217 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -704,6 +704,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_NZR_SEM_USB_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_1_PID) }, { USB_DEVICE(ICOM_VID, ICOM_OPC_U_UC_PID) }, { USB_DEVICE(ICOM_VID, ICOM_ID_RP2C1_PID) }, @@ -804,13 +805,32 @@ static struct usb_device_id id_table_combined [] = { .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(ADI_VID, ADI_GNICEPLUS_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, - { USB_DEVICE(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID) }, + { USB_DEVICE_AND_INTERFACE_INFO(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID, + USB_CLASS_VENDOR_SPEC, + USB_SUBCLASS_VENDOR_SPEC, 0x00) }, { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) }, { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, + { USB_DEVICE(FTDI_VID, PI_C865_PID) }, + { USB_DEVICE(FTDI_VID, PI_C857_PID) }, + { USB_DEVICE(PI_VID, PI_C866_PID) }, + { USB_DEVICE(PI_VID, PI_C663_PID) }, + { USB_DEVICE(PI_VID, PI_C725_PID) }, + { USB_DEVICE(PI_VID, PI_E517_PID) }, + { USB_DEVICE(PI_VID, PI_C863_PID) }, { USB_DEVICE(PI_VID, PI_E861_PID) }, + { USB_DEVICE(PI_VID, PI_C867_PID) }, + { USB_DEVICE(PI_VID, PI_E609_PID) }, + { USB_DEVICE(PI_VID, PI_E709_PID) }, + { USB_DEVICE(PI_VID, PI_100F_PID) }, + { USB_DEVICE(PI_VID, PI_1011_PID) }, + { USB_DEVICE(PI_VID, PI_1012_PID) }, + { USB_DEVICE(PI_VID, PI_1013_PID) }, + { USB_DEVICE(PI_VID, PI_1014_PID) }, + { USB_DEVICE(PI_VID, PI_1015_PID) }, + { USB_DEVICE(PI_VID, PI_1016_PID) }, { USB_DEVICE(KONDO_VID, KONDO_USB_SERIAL_PID) }, { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID), diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 5dd96ca6c380..41fe5826100c 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -75,6 +75,9 @@ #define FTDI_OPENDCC_GATEWAY_PID 0xBFDB #define FTDI_OPENDCC_GBM_PID 0xBFDC +/* NZR SEM 16+ USB (http://www.nzr.de) */ +#define FTDI_NZR_SEM_USB_PID 0xC1E0 /* NZR SEM-LOG16+ */ + /* * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com) */ @@ -539,7 +542,10 @@ /* * Microchip Technology, Inc. * - * MICROCHIP_VID (0x04D8) and MICROCHIP_USB_BOARD_PID (0x000A) are also used by: + * MICROCHIP_VID (0x04D8) and MICROCHIP_USB_BOARD_PID (0x000A) are + * used by single function CDC ACM class based firmware demo + * applications. The VID/PID has also been used in firmware + * emulating FTDI serial chips by: * Hornby Elite - Digital Command Control Console * http://www.hornby.com/hornby-dcc/controllers/ */ @@ -791,8 +797,27 @@ * Physik Instrumente * http://www.physikinstrumente.com/en/products/ */ +/* These two devices use the VID of FTDI */ +#define PI_C865_PID 0xe0a0 /* PI C-865 Piezomotor Controller */ +#define PI_C857_PID 0xe0a1 /* PI Encoder Trigger Box */ + #define PI_VID 0x1a72 /* Vendor ID */ -#define PI_E861_PID 0x1008 /* E-861 piezo controller USB connection */ +#define PI_C866_PID 0x1000 /* PI C-866 Piezomotor Controller */ +#define PI_C663_PID 0x1001 /* PI C-663 Mercury-Step */ +#define PI_C725_PID 0x1002 /* PI C-725 Piezomotor Controller */ +#define PI_E517_PID 0x1005 /* PI E-517 Digital Piezo Controller Operation Module */ +#define PI_C863_PID 0x1007 /* PI C-863 */ +#define PI_E861_PID 0x1008 /* PI E-861 Piezomotor Controller */ +#define PI_C867_PID 0x1009 /* PI C-867 Piezomotor Controller */ +#define PI_E609_PID 0x100D /* PI E-609 Digital Piezo Controller */ +#define PI_E709_PID 0x100E /* PI E-709 Digital Piezo Controller */ +#define PI_100F_PID 0x100F /* PI Digital Piezo Controller */ +#define PI_1011_PID 0x1011 /* PI Digital Piezo Controller */ +#define PI_1012_PID 0x1012 /* PI Motion Controller */ +#define PI_1013_PID 0x1013 /* PI Motion Controller */ +#define PI_1014_PID 0x1014 /* PI Device */ +#define PI_1015_PID 0x1015 /* PI Device */ +#define PI_1016_PID 0x1016 /* PI Digital Servo Module */ /* * Kondo Kagaku Co.Ltd. diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index cc40f47ecea1..5ce88d1bc6f1 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -886,8 +886,6 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1010, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf4_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1012, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1018, 0xff, 0xff, 0xff), - .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1057, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1058, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1059, 0xff, 0xff, 0xff) }, @@ -1092,6 +1090,10 @@ static const struct usb_device_id option_ids[] = { .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist }, + { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) }, + { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) }, + { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) }, + { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, { USB_DEVICE(ALINK_VENDOR_ID, DLINK_PRODUCT_DWM_652_U5) }, /* Yes, ALINK_VENDOR_ID */ |