sky2: safer transmit timeout

Rather than trying to be "smart" about possible transmit timeout
causes. Just clear all pending frames and reset the PHY.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 15 insertions, 26 deletions

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index e97dc299b563..c96362dae800 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1840,48 +1840,37 @@ out:
 }
 
 
-/* Transmit timeout is only called if we are running, carries is up
+/* Transmit timeout is only called if we are running, carrier is up
  * and tx queue is full (stopped).
+ * Called with netif_tx_lock held.
  */
 static void sky2_tx_timeout(struct net_device *dev)
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
 	struct sky2_hw *hw = sky2->hw;
-	unsigned txq = txqaddr[sky2->port];
-	u16 report, done;
+	u32 imask;
 
 	if (netif_msg_timer(sky2))
 		printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
 
-	report = sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX);
-	done = sky2_read16(hw, Q_ADDR(txq, Q_DONE));
-
 	printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
-	       dev->name,
-	       sky2->tx_cons, sky2->tx_prod, report, done);
-
-	if (report != done) {
-		printk(KERN_INFO PFX "status burst pending (irq moderation?)\n");
+	       dev->name, sky2->tx_cons, sky2->tx_prod,
+	       sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
+	       sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
 
-		sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
-		sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
-	} else if (report != sky2->tx_cons) {
-		printk(KERN_INFO PFX "status report lost?\n");
+	imask = sky2_read32(hw, B0_IMSK);	/* block IRQ in hw */
+	sky2_write32(hw, B0_IMSK, 0);
+	sky2_read32(hw, B0_IMSK);
 
-		netif_tx_lock_bh(dev);
-		sky2_tx_complete(sky2, report);
-		netif_tx_unlock_bh(dev);
-	} else {
-		printk(KERN_INFO PFX "hardware hung? flushing\n");
+	netif_poll_disable(hw->dev[0]);		/* stop NAPI poll */
+	synchronize_irq(hw->pdev->irq);
 
-		sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
-		sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
+	netif_start_queue(dev);			/* don't wakeup during flush */
+	sky2_tx_complete(sky2, sky2->tx_prod);	/* Flush transmit queue */
 
-		sky2_tx_clean(dev);
+	sky2_write32(hw, B0_IMSK, imask);
 
-		sky2_qset(hw, txq);
-		sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
-	}
+	sky2_phy_reinit(sky2);			/* this clears flow control etc */
 }
 
 static int sky2_change_mtu(struct net_device *dev, int new_mtu)