Merge branch 'linux-2.6'

16 files changed, 1815 insertions, 416 deletions

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 90621c3312bc..c9832d963f1e 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -251,9 +251,16 @@ static const struct serial8250_config uart_config[] = {
 		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
 		.flags		= UART_CAP_FIFO | UART_CAP_UUE,
 	},
+	[PORT_RM9000] = {
+		.name		= "RM9000",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO,
+	},
 };
 
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
 
 /* Au1x00 UART hardware has a weird register layout */
 static const u8 au_io_in_map[] = {
@@ -289,6 +296,44 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
 	return au_io_out_map[offset];
 }
 
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+
+static const u8
+	regmap_in[8] = {
+		[UART_RX]	= 0x00,
+		[UART_IER]	= 0x0c,
+		[UART_IIR]	= 0x14,
+		[UART_LCR]	= 0x1c,
+		[UART_MCR]	= 0x20,
+		[UART_LSR]	= 0x24,
+		[UART_MSR]	= 0x28,
+		[UART_SCR]	= 0x2c
+	},
+	regmap_out[8] = {
+		[UART_TX] 	= 0x04,
+		[UART_IER]	= 0x0c,
+		[UART_FCR]	= 0x18,
+		[UART_LCR]	= 0x1c,
+		[UART_MCR]	= 0x20,
+		[UART_LSR]	= 0x24,
+		[UART_MSR]	= 0x28,
+		[UART_SCR]	= 0x2c
+	};
+
+static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+{
+	if (up->port.iotype != UPIO_RM9000)
+		return offset;
+	return regmap_in[offset];
+}
+
+static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+{
+	if (up->port.iotype != UPIO_RM9000)
+		return offset;
+	return regmap_out[offset];
+}
+
 #else
 
 /* sane hardware needs no mapping */
@@ -308,8 +353,10 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
 		return inb(up->port.iobase + 1);
 
 	case UPIO_MEM:
+	case UPIO_DWAPB:
 		return readb(up->port.membase + offset);
 
+	case UPIO_RM9000:
 	case UPIO_MEM32:
 		return readl(up->port.membase + offset);
 
@@ -333,6 +380,8 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
 static void
 serial_out(struct uart_8250_port *up, int offset, int value)
 {
+	/* Save the offset before it's remapped */
+	int save_offset = offset;
 	offset = map_8250_out_reg(up, offset) << up->port.regshift;
 
 	switch (up->port.iotype) {
@@ -345,6 +394,7 @@ serial_out(struct uart_8250_port *up, int offset, int value)
 		writeb(value, up->port.membase + offset);
 		break;
 
+	case UPIO_RM9000:
 	case UPIO_MEM32:
 		writel(value, up->port.membase + offset);
 		break;
@@ -359,6 +409,18 @@ serial_out(struct uart_8250_port *up, int offset, int value)
 			writeb(value, up->port.membase + offset);
 		break;
 
+	case UPIO_DWAPB:
+		/* Save the LCR value so it can be re-written when a
+		 * Busy Detect interrupt occurs. */
+		if (save_offset == UART_LCR)
+			up->lcr = value;
+		writeb(value, up->port.membase + offset);
+		/* Read the IER to ensure any interrupt is cleared before
+		 * returning from ISR. */
+		if (save_offset == UART_TX || save_offset == UART_IER)
+			value = serial_in(up, UART_IER);
+		break;
+
 	default:
 		outb(value, up->port.iobase + offset);
 	}
@@ -373,6 +435,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
 #ifdef CONFIG_SERIAL_8250_AU1X00
 	case UPIO_AU:
 #endif
+	case UPIO_DWAPB:
 		serial_out(up, offset, value);
 		serial_in(up, UART_LCR);	/* safe, no side-effects */
 		break;
@@ -403,7 +466,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value)
 	serial_outp(up, UART_DLM, value >> 8 & 0xff);
 }
 
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
 /* Au1x00 haven't got a standard divisor latch */
 static int serial_dl_read(struct uart_8250_port *up)
 {
@@ -420,6 +483,24 @@ static void serial_dl_write(struct uart_8250_port *up, int value)
 	else
 		_serial_dl_write(up, value);
 }
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+static int serial_dl_read(struct uart_8250_port *up)
+{
+	return	(up->port.iotype == UPIO_RM9000) ?
+		(((__raw_readl(up->port.membase + 0x10) << 8) |
+		(__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) :
+		_serial_dl_read(up);
+}
+
+static void serial_dl_write(struct uart_8250_port *up, int value)
+{
+	if (up->port.iotype == UPIO_RM9000) {
+		__raw_writel(value, up->port.membase + 0x08);
+		__raw_writel(value >> 8, up->port.membase + 0x10);
+	} else {
+		_serial_dl_write(up, value);
+	}
+}
 #else
 #define serial_dl_read(up) _serial_dl_read(up)
 #define serial_dl_write(up, value) _serial_dl_write(up, value)
@@ -621,7 +702,7 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
  * its clones.  (We treat the broken original StarTech 16650 V1 as a
  * 16550, and why not?  Startech doesn't seem to even acknowledge its
  * existence.)
- * 
+ *
  * What evil have men's minds wrought...
  */
 static void autoconfig_has_efr(struct uart_8250_port *up)
@@ -674,7 +755,7 @@ static void autoconfig_has_efr(struct uart_8250_port *up)
 			up->bugs |= UART_BUG_QUOT;
 		return;
 	}
-	
+
 	/*
 	 * We check for a XR16C850 by setting DLL and DLM to 0, and then
 	 * reading back DLL and DLM.  The chip type depends on the DLM
@@ -817,7 +898,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 			status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
 			status1 |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
 			serial_outp(up, 0x04, status1);
-			
+
 			serial_dl_write(up, quot);
 
 			serial_outp(up, UART_LCR, 0);
@@ -922,7 +1003,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 		/*
 		 * Do a simple existence test first; if we fail this,
 		 * there's no point trying anything else.
-		 * 
+		 *
 		 * 0x80 is used as a nonsense port to prevent against
 		 * false positives due to ISA bus float.  The
 		 * assumption is that 0x80 is a non-existent port;
@@ -961,7 +1042,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 	save_mcr = serial_in(up, UART_MCR);
 	save_lcr = serial_in(up, UART_LCR);
 
-	/* 
+	/*
 	 * Check to see if a UART is really there.  Certain broken
 	 * internal modems based on the Rockwell chipset fail this
 	 * test, because they apparently don't implement the loopback
@@ -1068,7 +1149,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 	else
 		serial_outp(up, UART_IER, 0);
 
- out:	
+ out:
 	spin_unlock_irqrestore(&up->port.lock, flags);
 //	restore_flags(flags);
 	DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
@@ -1094,7 +1175,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
 	save_mcr = serial_inp(up, UART_MCR);
 	save_ier = serial_inp(up, UART_IER);
 	serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-	
+
 	irqs = probe_irq_on();
 	serial_outp(up, UART_MCR, 0);
 	udelay (10);
@@ -1159,8 +1240,11 @@ static void serial8250_start_tx(struct uart_port *port)
 		if (up->bugs & UART_BUG_TXEN) {
 			unsigned char lsr, iir;
 			lsr = serial_in(up, UART_LSR);
-			iir = serial_in(up, UART_IIR);
-			if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
+			iir = serial_in(up, UART_IIR) & 0x0f;
+			if ((up->port.type == PORT_RM9000) ?
+				(lsr & UART_LSR_THRE &&
+				(iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) :
+				(lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT))
 				transmit_chars(up);
 		}
 	}
@@ -1389,6 +1473,19 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
 			handled = 1;
 
 			end = NULL;
+		} else if (up->port.iotype == UPIO_DWAPB &&
+			  (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
+			/* The DesignWare APB UART has an Busy Detect (0x07)
+			 * interrupt meaning an LCR write attempt occured while the
+			 * UART was busy. The interrupt must be cleared by reading
+			 * the UART status register (USR) and the LCR re-written. */
+			unsigned int status;
+			status = *(volatile u32 *)up->port.private_data;
+			serial_out(up, UART_LCR, up->lcr);
+
+			handled = 1;
+
+			end = NULL;
 		} else if (end == NULL)
 			end = l;
 
@@ -1928,7 +2025,7 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
 	/*
 	 * Ask the core to calculate the divisor for us.
 	 */
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 	quot = serial8250_get_divisor(port, baud);
 
 	/*
@@ -2090,6 +2187,7 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
+	case UPIO_DWAPB:
 		if (!up->port.mapbase)
 			break;
 
@@ -2127,6 +2225,7 @@ static void serial8250_release_std_resource(struct uart_8250_port *up)
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
+	case UPIO_DWAPB:
 		if (!up->port.mapbase)
 			break;
 
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ad9f321968e1..924e9bd757f0 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -254,6 +254,15 @@ config SERIAL_8250_AU1X00
 	  to this option.  The driver can handle 1 or 2 serial ports.
 	  If unsure, say N.
 
+config SERIAL_8250_RM9K
+	bool "Support for MIPS RM9xxx integrated serial port"
+	depends on SERIAL_8250 != n && SERIAL_RM9000
+	select SERIAL_8250_SHARE_IRQ
+	help
+	  Selecting this option will add support for the integrated serial
+	  port hardware found on MIPS RM9122 and similar processors.
+	  If unsure, say N.
+
 comment "Non-8250 serial port support"
 
 config SERIAL_AMBA_PL010
@@ -499,6 +508,100 @@ config SERIAL_SA1100_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_BFIN
+	tristate "Blackfin serial port support"
+	depends on BFIN
+	select SERIAL_CORE
+	select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
+	help
+	  Add support for the built-in UARTs on the Blackfin.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_5xx.
+
+config SERIAL_BFIN_CONSOLE
+	bool "Console on Blackfin serial port"
+	depends on SERIAL_BFIN
+	select SERIAL_CORE_CONSOLE
+
+choice
+	prompt "UART Mode"
+	depends on SERIAL_BFIN
+	default SERIAL_BFIN_DMA
+	help
+	  This driver supports the built-in serial ports of the Blackfin family
+	  of CPUs
+
+config SERIAL_BFIN_DMA
+	bool "DMA mode"
+	depends on DMA_UNCACHED_1M
+	help
+	  This driver works under DMA mode. If this option is selected, the
+	  blackfin simple dma driver is also enabled.
+
+config SERIAL_BFIN_PIO
+	bool "PIO mode"
+	help
+	  This driver works under PIO mode.
+
+endchoice
+
+config SERIAL_BFIN_UART0
+	bool "Enable UART0"
+	depends on SERIAL_BFIN
+	help
+	  Enable UART0
+
+config BFIN_UART0_CTSRTS
+	bool "Enable UART0 hardware flow control"
+	depends on SERIAL_BFIN_UART0
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART0_CTS_PIN
+	int "UART0 CTS pin"
+	depends on BFIN_UART0_CTSRTS
+	default 23
+	help
+	  The default pin is GPIO_GP7.
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART0_RTS_PIN
+	int "UART0 RTS pin"
+	depends on BFIN_UART0_CTSRTS
+	default 22
+	help
+	  The default pin is GPIO_GP6.
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART1
+	bool "Enable UART1"
+	depends on SERIAL_BFIN && (BF534 || BF536 || BF537)
+	help
+	  Enable UART1
+
+config BFIN_UART1_CTSRTS
+	bool "Enable UART1 hardware flow control"
+	depends on SERIAL_BFIN_UART1
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART1_CTS_PIN
+	int "UART1 CTS pin"
+	depends on BFIN_UART1_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART1_RTS_PIN
+	int "UART1 RTS pin"
+	depends on BFIN_UART1_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
 config SERIAL_IMX
 	bool "IMX serial port support"
 	depends on ARM && ARCH_IMX
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 6b3560c5749a..4959bcb8d1ef 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
 obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
 obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c
index f69bd097166e..1a9a24b82636 100644
--- a/drivers/serial/amba-pl010.c
+++ b/drivers/serial/amba-pl010.c
@@ -48,6 +48,7 @@
 #include <linux/serial.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/serial.h>
+#include <linux/clk.h>
 
 #include <asm/io.h>
 
@@ -70,6 +71,7 @@
  */
 struct uart_amba_port {
 	struct uart_port	port;
+	struct clk		*clk;
 	struct amba_device	*dev;
 	struct amba_pl010_data	*data;
 	unsigned int		old_status;
@@ -77,73 +79,77 @@ struct uart_amba_port {
 
 static void pl010_stop_tx(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int cr;
 
-	cr = readb(port->membase + UART010_CR);
+	cr = readb(uap->port.membase + UART010_CR);
 	cr &= ~UART010_CR_TIE;
-	writel(cr, port->membase + UART010_CR);
+	writel(cr, uap->port.membase + UART010_CR);
 }
 
 static void pl010_start_tx(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int cr;
 
-	cr = readb(port->membase + UART010_CR);
+	cr = readb(uap->port.membase + UART010_CR);
 	cr |= UART010_CR_TIE;
-	writel(cr, port->membase + UART010_CR);
+	writel(cr, uap->port.membase + UART010_CR);
 }
 
 static void pl010_stop_rx(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int cr;
 
-	cr = readb(port->membase + UART010_CR);
+	cr = readb(uap->port.membase + UART010_CR);
 	cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
-	writel(cr, port->membase + UART010_CR);
+	writel(cr, uap->port.membase + UART010_CR);
 }
 
 static void pl010_enable_ms(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int cr;
 
-	cr = readb(port->membase + UART010_CR);
+	cr = readb(uap->port.membase + UART010_CR);
 	cr |= UART010_CR_MSIE;
-	writel(cr, port->membase + UART010_CR);
+	writel(cr, uap->port.membase + UART010_CR);
 }
 
-static void pl010_rx_chars(struct uart_port *port)
+static void pl010_rx_chars(struct uart_amba_port *uap)
 {
-	struct tty_struct *tty = port->info->tty;
+	struct tty_struct *tty = uap->port.info->tty;
 	unsigned int status, ch, flag, rsr, max_count = 256;
 
-	status = readb(port->membase + UART01x_FR);
+	status = readb(uap->port.membase + UART01x_FR);
 	while (UART_RX_DATA(status) && max_count--) {
-		ch = readb(port->membase + UART01x_DR);
+		ch = readb(uap->port.membase + UART01x_DR);
 		flag = TTY_NORMAL;
 
-		port->icount.rx++;
+		uap->port.icount.rx++;
 
 		/*
 		 * Note that the error handling code is
 		 * out of the main execution path
 		 */
-		rsr = readb(port->membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+		rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
 		if (unlikely(rsr & UART01x_RSR_ANY)) {
-			writel(0, port->membase + UART01x_ECR);
+			writel(0, uap->port.membase + UART01x_ECR);
 
 			if (rsr & UART01x_RSR_BE) {
 				rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
-				port->icount.brk++;
-				if (uart_handle_break(port))
+				uap->port.icount.brk++;
+				if (uart_handle_break(&uap->port))
 					goto ignore_char;
 			} else if (rsr & UART01x_RSR_PE)
-				port->icount.parity++;
+				uap->port.icount.parity++;
 			else if (rsr & UART01x_RSR_FE)
-				port->icount.frame++;
+				uap->port.icount.frame++;
 			if (rsr & UART01x_RSR_OE)
-				port->icount.overrun++;
+				uap->port.icount.overrun++;
 
-			rsr &= port->read_status_mask;
+			rsr &= uap->port.read_status_mask;
 
 			if (rsr & UART01x_RSR_BE)
 				flag = TTY_BREAK;
@@ -153,53 +159,52 @@ static void pl010_rx_chars(struct uart_port *port)
 				flag = TTY_FRAME;
 		}
 
-		if (uart_handle_sysrq_char(port, ch))
+		if (uart_handle_sysrq_char(&uap->port, ch))
 			goto ignore_char;
 
-		uart_insert_char(port, rsr, UART01x_RSR_OE, ch, flag);
+		uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
 
 	ignore_char:
-		status = readb(port->membase + UART01x_FR);
+		status = readb(uap->port.membase + UART01x_FR);
 	}
 	tty_flip_buffer_push(tty);
 	return;
 }
 
-static void pl010_tx_chars(struct uart_port *port)
+static void pl010_tx_chars(struct uart_amba_port *uap)
 {
-	struct circ_buf *xmit = &port->info->xmit;
+	struct circ_buf *xmit = &uap->port.info->xmit;
 	int count;
 
-	if (port->x_char) {
-		writel(port->x_char, port->membase + UART01x_DR);
-		port->icount.tx++;
-		port->x_char = 0;
+	if (uap->port.x_char) {
+		writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+		uap->port.icount.tx++;
+		uap->port.x_char = 0;
 		return;
 	}
-	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
-		pl010_stop_tx(port);
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
+		pl010_stop_tx(&uap->port);
 		return;
 	}
 
-	count = port->fifosize >> 1;
+	count = uap->port.fifosize >> 1;
 	do {
-		writel(xmit->buf[xmit->tail], port->membase + UART01x_DR);
+		writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		port->icount.tx++;
+		uap->port.icount.tx++;
 		if (uart_circ_empty(xmit))
 			break;
 	} while (--count > 0);
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(port);
+		uart_write_wakeup(&uap->port);
 
 	if (uart_circ_empty(xmit))
-		pl010_stop_tx(port);
+		pl010_stop_tx(&uap->port);
 }
 
-static void pl010_modem_status(struct uart_port *port)
+static void pl010_modem_status(struct uart_amba_port *uap)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int status, delta;
 
 	writel(0, uap->port.membase + UART010_ICR);
@@ -226,47 +231,50 @@ static void pl010_modem_status(struct uart_port *port)
 
 static irqreturn_t pl010_int(int irq, void *dev_id)
 {
-	struct uart_port *port = dev_id;
+	struct uart_amba_port *uap = dev_id;
 	unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
 	int handled = 0;
 
-	spin_lock(&port->lock);
+	spin_lock(&uap->port.lock);
 
-	status = readb(port->membase + UART010_IIR);
+	status = readb(uap->port.membase + UART010_IIR);
 	if (status) {
 		do {
 			if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
-				pl010_rx_chars(port);
+				pl010_rx_chars(uap);
 			if (status & UART010_IIR_MIS)
-				pl010_modem_status(port);
+				pl010_modem_status(uap);
 			if (status & UART010_IIR_TIS)
-				pl010_tx_chars(port);
+				pl010_tx_chars(uap);
 
 			if (pass_counter-- == 0)
 				break;
 
-			status = readb(port->membase + UART010_IIR);
+			status = readb(uap->port.membase + UART010_IIR);
 		} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
 				   UART010_IIR_TIS));
 		handled = 1;
 	}
 
-	spin_unlock(&port->lock);
+	spin_unlock(&uap->port.lock);
 
 	return IRQ_RETVAL(handled);
 }
 
 static unsigned int pl010_tx_empty(struct uart_port *port)
 {
-	return readb(port->membase + UART01x_FR) & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned int status = readb(uap->port.membase + UART01x_FR);
+	return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
 }
 
 static unsigned int pl010_get_mctrl(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int result = 0;
 	unsigned int status;
 
-	status = readb(port->membase + UART01x_FR);
+	status = readb(uap->port.membase + UART01x_FR);
 	if (status & UART01x_FR_DCD)
 		result |= TIOCM_CAR;
 	if (status & UART01x_FR_DSR)
@@ -287,17 +295,18 @@ static void pl010_set_mctrl(struct uart_port *port, unsigned int mctrl)
 
 static void pl010_break_ctl(struct uart_port *port, int break_state)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned long flags;
 	unsigned int lcr_h;
 
-	spin_lock_irqsave(&port->lock, flags);
-	lcr_h = readb(port->membase + UART010_LCRH);
+	spin_lock_irqsave(&uap->port.lock, flags);
+	lcr_h = readb(uap->port.membase + UART010_LCRH);
 	if (break_state == -1)
 		lcr_h |= UART01x_LCRH_BRK;
 	else
 		lcr_h &= ~UART01x_LCRH_BRK;
-	writel(lcr_h, port->membase + UART010_LCRH);
-	spin_unlock_irqrestore(&port->lock, flags);
+	writel(lcr_h, uap->port.membase + UART010_LCRH);
+	spin_unlock_irqrestore(&uap->port.lock, flags);
 }
 
 static int pl010_startup(struct uart_port *port)
@@ -306,48 +315,70 @@ static int pl010_startup(struct uart_port *port)
 	int retval;
 
 	/*
+	 * Try to enable the clock producer.
+	 */
+	retval = clk_enable(uap->clk);
+	if (retval)
+		goto out;
+
+	uap->port.uartclk = clk_get_rate(uap->clk);
+
+	/*
 	 * Allocate the IRQ
 	 */
-	retval = request_irq(port->irq, pl010_int, 0, "uart-pl010", port);
+	retval = request_irq(uap->port.irq, pl010_int, 0, "uart-pl010", uap);
 	if (retval)
-		return retval;
+		goto clk_dis;
 
 	/*
 	 * initialise the old status of the modem signals
 	 */
-	uap->old_status = readb(port->membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+	uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
 
 	/*
 	 * Finally, enable interrupts
 	 */
 	writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
-	       port->membase + UART010_CR);
+	       uap->port.membase + UART010_CR);
 
 	return 0;
+
+ clk_dis:
+	clk_disable(uap->clk);
+ out:
+	return retval;
 }
 
 static void pl010_shutdown(struct uart_port *port)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
 	/*
 	 * Free the interrupt
 	 */
-	free_irq(port->irq, port);
+	free_irq(uap->port.irq, uap);
 
 	/*
 	 * disable all interrupts, disable the port
 	 */
-	writel(0, port->membase + UART010_CR);
+	writel(0, uap->port.membase + UART010_CR);
 
 	/* disable break condition and fifos */
-	writel(readb(port->membase + UART010_LCRH) &
+	writel(readb(uap->port.membase + UART010_LCRH) &
 		~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
-	       port->membase + UART010_LCRH);
+	       uap->port.membase + UART010_LCRH);
+
+	/*
+	 * Shut down the clock producer
+	 */
+	clk_disable(uap->clk);
 }
 
 static void
 pl010_set_termios(struct uart_port *port, struct ktermios *termios,
 		     struct ktermios *old)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int lcr_h, old_cr;
 	unsigned long flags;
 	unsigned int baud, quot;
@@ -355,7 +386,7 @@ pl010_set_termios(struct uart_port *port, struct ktermios *termios,
 	/*
 	 * Ask the core to calculate the divisor for us.
 	 */
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
+	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
 	quot = uart_get_divisor(port, baud);
 
 	switch (termios->c_cflag & CSIZE) {
@@ -379,66 +410,66 @@ pl010_set_termios(struct uart_port *port, struct ktermios *termios,
 		if (!(termios->c_cflag & PARODD))
 			lcr_h |= UART01x_LCRH_EPS;
 	}
-	if (port->fifosize > 1)
+	if (uap->port.fifosize > 1)
 		lcr_h |= UART01x_LCRH_FEN;
 
-	spin_lock_irqsave(&port->lock, flags);
+	spin_lock_irqsave(&uap->port.lock, flags);
 
 	/*
 	 * Update the per-port timeout.
 	 */
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	port->read_status_mask = UART01x_RSR_OE;
+	uap->port.read_status_mask = UART01x_RSR_OE;
 	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+		uap->port.read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
 	if (termios->c_iflag & (BRKINT | PARMRK))
-		port->read_status_mask |= UART01x_RSR_BE;
+		uap->port.read_status_mask |= UART01x_RSR_BE;
 
 	/*
 	 * Characters to ignore
 	 */
-	port->ignore_status_mask = 0;
+	uap->port.ignore_status_mask = 0;
 	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+		uap->port.ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
 	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= UART01x_RSR_BE;
+		uap->port.ignore_status_mask |= UART01x_RSR_BE;
 		/*
 		 * If we're ignoring parity and break indicators,
 		 * ignore overruns too (for real raw support).
 		 */
 		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= UART01x_RSR_OE;
+			uap->port.ignore_status_mask |= UART01x_RSR_OE;
 	}
 
 	/*
 	 * Ignore all characters if CREAD is not set.
 	 */
 	if ((termios->c_cflag & CREAD) == 0)
-		port->ignore_status_mask |= UART_DUMMY_RSR_RX;
+		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
 
 	/* first, disable everything */
-	old_cr = readb(port->membase + UART010_CR) & ~UART010_CR_MSIE;
+	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
 
 	if (UART_ENABLE_MS(port, termios->c_cflag))
 		old_cr |= UART010_CR_MSIE;
 
-	writel(0, port->membase + UART010_CR);
+	writel(0, uap->port.membase + UART010_CR);
 
 	/* Set baud rate */
 	quot -= 1;
-	writel((quot & 0xf00) >> 8, port->membase + UART010_LCRM);
-	writel(quot & 0xff, port->membase + UART010_LCRL);
+	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+	writel(quot & 0xff, uap->port.membase + UART010_LCRL);
 
 	/*
 	 * ----------v----------v----------v----------v-----
 	 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
 	 * ----------^----------^----------^----------^-----
 	 */
-	writel(lcr_h, port->membase + UART010_LCRH);
-	writel(old_cr, port->membase + UART010_CR);
+	writel(lcr_h, uap->port.membase + UART010_LCRH);
+	writel(old_cr, uap->port.membase + UART010_CR);
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	spin_unlock_irqrestore(&uap->port.lock, flags);
 }
 
 static const char *pl010_type(struct uart_port *port)
@@ -514,47 +545,52 @@ static struct uart_amba_port *amba_ports[UART_NR];
 
 static void pl010_console_putchar(struct uart_port *port, int ch)
 {
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int status;
 
 	do {
-		status = readb(port->membase + UART01x_FR);
+		status = readb(uap->port.membase + UART01x_FR);
 		barrier();
 	} while (!UART_TX_READY(status));
-	writel(ch, port->membase + UART01x_DR);
+	writel(ch, uap->port.membase + UART01x_DR);
 }
 
 static void
 pl010_console_write(struct console *co, const char *s, unsigned int count)
 {
-	struct uart_port *port = &amba_ports[co->index]->port;
+	struct uart_amba_port *uap = amba_ports[co->index];
 	unsigned int status, old_cr;
 
+	clk_enable(uap->clk);
+
 	/*
 	 *	First save the CR then disable the interrupts
 	 */
-	old_cr = readb(port->membase + UART010_CR);
-	writel(UART01x_CR_UARTEN, port->membase + UART010_CR);
+	old_cr = readb(uap->port.membase + UART010_CR);
+	writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
 
-	uart_console_write(port, s, count, pl010_console_putchar);
+	uart_console_write(&uap->port, s, count, pl010_console_putchar);
 
 	/*
 	 *	Finally, wait for transmitter to become empty
 	 *	and restore the TCR
 	 */
 	do {
-		status = readb(port->membase + UART01x_FR);
+		status = readb(uap->port.membase + UART01x_FR);
 		barrier();
 	} while (status & UART01x_FR_BUSY);
-	writel(old_cr, port->membase + UART010_CR);
+	writel(old_cr, uap->port.membase + UART010_CR);
+
+	clk_disable(uap->clk);
 }
 
 static void __init
-pl010_console_get_options(struct uart_port *port, int *baud,
+pl010_console_get_options(struct uart_amba_port *uap, int *baud,
 			     int *parity, int *bits)
 {
-	if (readb(port->membase + UART010_CR) & UART01x_CR_UARTEN) {
+	if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
 		unsigned int lcr_h, quot;
-		lcr_h = readb(port->membase + UART010_LCRH);
+		lcr_h = readb(uap->port.membase + UART010_LCRH);
 
 		*parity = 'n';
 		if (lcr_h & UART01x_LCRH_PEN) {
@@ -569,14 +605,15 @@ pl010_console_get_options(struct uart_port *port, int *baud,
 		else
 			*bits = 8;
 
-		quot = readb(port->membase + UART010_LCRL) | readb(port->membase + UART010_LCRM) << 8;
-		*baud = port->uartclk / (16 * (quot + 1));
+		quot = readb(uap->port.membase + UART010_LCRL) |
+		       readb(uap->port.membase + UART010_LCRM) << 8;
+		*baud = uap->port.uartclk / (16 * (quot + 1));
 	}
 }
 
 static int __init pl010_console_setup(struct console *co, char *options)
 {
-	struct uart_port *port;
+	struct uart_amba_port *uap;
 	int baud = 38400;
 	int bits = 8;
 	int parity = 'n';
@@ -589,16 +626,18 @@ static int __init pl010_console_setup(struct console *co, char *options)
 	 */
 	if (co->index >= UART_NR)
 		co->index = 0;
-	if (!amba_ports[co->index])
+	uap = amba_ports[co->index];
+	if (!uap)
 		return -ENODEV;
-	port = &amba_ports[co->index]->port;
+
+	uap->port.uartclk = clk_get_rate(uap->clk);
 
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 	else
-		pl010_console_get_options(port, &baud, &parity, &bits);
+		pl010_console_get_options(uap, &baud, &parity, &bits);
 
-	return uart_set_options(port, co, baud, parity, bits, flow);
+	return uart_set_options(&uap->port, co, baud, parity, bits, flow);
 }
 
 static struct uart_driver amba_reg;
@@ -629,7 +668,7 @@ static struct uart_driver amba_reg = {
 
 static int pl010_probe(struct amba_device *dev, void *id)
 {
-	struct uart_amba_port *port;
+	struct uart_amba_port *uap;
 	void __iomem *base;
 	int i, ret;
 
@@ -642,8 +681,8 @@ static int pl010_probe(struct amba_device *dev, void *id)
 		goto out;
 	}
 
-	port = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
-	if (!port) {
+	uap = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
+	if (!uap) {
 		ret = -ENOMEM;
 		goto out;
 	}
@@ -654,51 +693,57 @@ static int pl010_probe(struct amba_device *dev, void *id)
 		goto free;
 	}
 
-	port->port.dev = &dev->dev;
-	port->port.mapbase = dev->res.start;
-	port->port.membase = base;
-	port->port.iotype = UPIO_MEM;
-	port->port.irq = dev->irq[0];
-	port->port.uartclk = 14745600;
-	port->port.fifosize = 16;
-	port->port.ops = &amba_pl010_pops;
-	port->port.flags = UPF_BOOT_AUTOCONF;
-	port->port.line = i;
-	port->dev = dev;
-	port->data = dev->dev.platform_data;
-
-	amba_ports[i] = port;
-
-	amba_set_drvdata(dev, port);
-	ret = uart_add_one_port(&amba_reg, &port->port);
+	uap->clk = clk_get(&dev->dev, "UARTCLK");
+	if (IS_ERR(uap->clk)) {
+		ret = PTR_ERR(uap->clk);
+		goto unmap;
+	}
+
+	uap->port.dev = &dev->dev;
+	uap->port.mapbase = dev->res.start;
+	uap->port.membase = base;
+	uap->port.iotype = UPIO_MEM;
+	uap->port.irq = dev->irq[0];
+	uap->port.fifosize = 16;
+	uap->port.ops = &amba_pl010_pops;
+	uap->port.flags = UPF_BOOT_AUTOCONF;
+	uap->port.line = i;
+	uap->dev = dev;
+	uap->data = dev->dev.platform_data;
+
+	amba_ports[i] = uap;
+
+	amba_set_drvdata(dev, uap);
+	ret = uart_add_one_port(&amba_reg, &uap->port);
 	if (ret) {
 		amba_set_drvdata(dev, NULL);
 		amba_ports[i] = NULL;
+		clk_put(uap->clk);
+ unmap:
 		iounmap(base);
  free:
-		kfree(port);
+		kfree(uap);
 	}
-
  out:
 	return ret;
 }
 
 static int pl010_remove(struct amba_device *dev)
 {
-	struct uart_amba_port *port = amba_get_drvdata(dev);
+	struct uart_amba_port *uap = amba_get_drvdata(dev);
 	int i;
 
 	amba_set_drvdata(dev, NULL);
 
-	uart_remove_one_port(&amba_reg, &port->port);
+	uart_remove_one_port(&amba_reg, &uap->port);
 
 	for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
-		if (amba_ports[i] == port)
+		if (amba_ports[i] == uap)
 			amba_ports[i] = NULL;
 
-	iounmap(port->port.membase);
-	kfree(port);
-
+	iounmap(uap->port.membase);
+	clk_put(uap->clk);
+	kfree(uap);
 	return 0;
 }
 
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 935f48fa501d..3320bcd92c0a 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -484,11 +484,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios * termios,
 	unsigned long flags;
 	unsigned int mode, imr, quot, baud;
 
+	/* Get current mode register */
+	mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 	quot = uart_get_divisor(port, baud);
 
-	/* Get current mode register */
-	mode = UART_GET_MR(port) & ~(ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+	if (quot > 65535) {		/* BRGR is 16-bit, so switch to slower clock */
+		quot /= 8;
+		mode |= ATMEL_US_USCLKS_MCK_DIV8;
+	}
 
 	/* byte size */
 	switch (termios->c_cflag & CSIZE) {
diff --git a/drivers/serial/atmel_serial.h b/drivers/serial/atmel_serial.h
index 11b44360e108..e0141776517c 100644
--- a/drivers/serial/atmel_serial.h
+++ b/drivers/serial/atmel_serial.h
@@ -46,6 +46,9 @@
 #define			ATMEL_US_USMODE_ISO7816_T1	6
 #define			ATMEL_US_USMODE_IRDA		8
 #define		ATMEL_US_USCLKS		(3   <<  4)		/* Clock Selection */
+#define			ATMEL_US_USCLKS_MCK		(0 <<  4)
+#define			ATMEL_US_USCLKS_MCK_DIV8	(1 <<  4)
+#define			ATMEL_US_USCLKS_SCK		(3 <<  4)
 #define		ATMEL_US_CHRL		(3   <<  6)		/* Character Length */
 #define			ATMEL_US_CHRL_5			(0 <<  6)
 #define			ATMEL_US_CHRL_6			(1 <<  6)
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
new file mode 100644
index 000000000000..408390f93db9
--- /dev/null
+++ b/drivers/serial/bfin_5xx.c
@@ -0,0 +1,1012 @@
+/*
+ * File:         drivers/serial/bfin_5xx.c
+ * Based on:     Based on drivers/serial/sa1100.c
+ * Author:       Aubrey Li <aubrey.li@analog.com>
+ *
+ * Created:
+ * Description:  Driver for blackfin 5xx serial ports
+ *
+ * Rev:          $Id: bfin_5xx.c,v 1.19 2006/09/24 02:33:53 aubrey Exp $
+ *
+ * Modified:
+ *               Copyright 2006 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+
+#include <asm/gpio.h>
+#include <asm/mach/bfin_serial_5xx.h>
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+#include <linux/dma-mapping.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/cacheflush.h>
+#endif
+
+/* UART name and device definitions */
+#define BFIN_SERIAL_NAME	"ttyBF"
+#define BFIN_SERIAL_MAJOR	204
+#define BFIN_SERIAL_MINOR	64
+
+/*
+ * Setup for console. Argument comes from the menuconfig
+ */
+#define DMA_RX_XCOUNT		512
+#define DMA_RX_YCOUNT		(PAGE_SIZE / DMA_RX_XCOUNT)
+
+#define DMA_RX_FLUSH_JIFFIES	5
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
+#else
+static void bfin_serial_do_work(struct work_struct *work);
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
+static void local_put_char(struct bfin_serial_port *uart, char ch);
+#endif
+
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
+
+/*
+ * interrupts are disabled on entry
+ */
+static void bfin_serial_stop_tx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	disable_dma(uart->tx_dma_channel);
+#else
+	unsigned short ier;
+
+	ier = UART_GET_IER(uart);
+	ier &= ~ETBEI;
+	UART_PUT_IER(uart, ier);
+#endif
+}
+
+/*
+ * port is locked and interrupts are disabled
+ */
+static void bfin_serial_start_tx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	bfin_serial_dma_tx_chars(uart);
+#else
+	unsigned short ier;
+	ier = UART_GET_IER(uart);
+	ier |= ETBEI;
+	UART_PUT_IER(uart, ier);
+	bfin_serial_tx_chars(uart);
+#endif
+}
+
+/*
+ * Interrupts are enabled
+ */
+static void bfin_serial_stop_rx(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned short ier;
+
+	ier = UART_GET_IER(uart);
+	ier &= ~ERBFI;
+	UART_PUT_IER(uart, ier);
+}
+
+/*
+ * Set the modem control timer to fire immediately.
+ */
+static void bfin_serial_enable_ms(struct uart_port *port)
+{
+}
+
+#ifdef CONFIG_SERIAL_BFIN_PIO
+static void local_put_char(struct bfin_serial_port *uart, char ch)
+{
+	unsigned short status;
+	int flags = 0;
+
+	spin_lock_irqsave(&uart->port.lock, flags);
+
+	do {
+		status = UART_GET_LSR(uart);
+	} while (!(status & THRE));
+
+	UART_PUT_CHAR(uart, ch);
+	SSYNC();
+
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
+{
+	struct tty_struct *tty = uart->port.info?uart->port.info->tty:0;
+	unsigned int status, ch, flg;
+#ifdef BF533_FAMILY
+	static int in_break = 0;
+#endif
+
+	status = UART_GET_LSR(uart);
+ 	ch = UART_GET_CHAR(uart);
+ 	uart->port.icount.rx++;
+
+#ifdef BF533_FAMILY
+	/* The BF533 family of processors have a nice misbehavior where
+	 * they continuously generate characters for a "single" break.
+	 * We have to basically ignore this flood until the "next" valid
+	 * character comes across.  All other Blackfin families operate
+	 * properly though.
+	 */
+	if (in_break) {
+		if (ch != 0) {
+			in_break = 0;
+			ch = UART_GET_CHAR(uart);
+		}
+		return;
+	}
+#endif
+
+	if (status & BI) {
+#ifdef BF533_FAMILY
+		in_break = 1;
+#endif
+		uart->port.icount.brk++;
+		if (uart_handle_break(&uart->port))
+			goto ignore_char;
+		flg = TTY_BREAK;
+	} else if (status & PE) {
+		flg = TTY_PARITY;
+		uart->port.icount.parity++;
+	} else if (status & OE) {
+		flg = TTY_OVERRUN;
+		uart->port.icount.overrun++;
+	} else if (status & FE) {
+		flg = TTY_FRAME;
+		uart->port.icount.frame++;
+	} else
+		flg = TTY_NORMAL;
+
+	if (uart_handle_sysrq_char(&uart->port, ch))
+		goto ignore_char;
+	if (tty)
+		uart_insert_char(&uart->port, status, 2, ch, flg);
+
+ignore_char:
+	if (tty)
+		tty_flip_buffer_push(tty);
+}
+
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
+{
+	struct circ_buf *xmit = &uart->port.info->xmit;
+
+	if (uart->port.x_char) {
+		UART_PUT_CHAR(uart, uart->port.x_char);
+		uart->port.icount.tx++;
+		uart->port.x_char = 0;
+		return;
+	}
+	/*
+	 * Check the modem control lines before
+	 * transmitting anything.
+	 */
+	bfin_serial_mctrl_check(uart);
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+		bfin_serial_stop_tx(&uart->port);
+		return;
+	}
+
+	local_put_char(uart, xmit->buf[xmit->tail]);
+	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+	uart->port.icount.tx++;
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&uart->port);
+
+	if (uart_circ_empty(xmit))
+		bfin_serial_stop_tx(&uart->port);
+}
+
+static irqreturn_t bfin_serial_int(int irq, void *dev_id)
+{
+	struct bfin_serial_port *uart = dev_id;
+	unsigned short status;
+
+	spin_lock(&uart->port.lock);
+	status = UART_GET_IIR(uart);
+	do {
+		if ((status & IIR_STATUS) == IIR_TX_READY)
+			bfin_serial_tx_chars(uart);
+		if ((status & IIR_STATUS) == IIR_RX_READY)
+			bfin_serial_rx_chars(uart);
+		status = UART_GET_IIR(uart);
+	} while (status & (IIR_TX_READY | IIR_RX_READY));
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+
+static void bfin_serial_do_work(struct work_struct *work)
+{
+	struct bfin_serial_port *uart = container_of(work, struct bfin_serial_port, cts_workqueue);
+
+	bfin_serial_mctrl_check(uart);
+}
+
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
+{
+	struct circ_buf *xmit = &uart->port.info->xmit;
+	unsigned short ier;
+	int flags = 0;
+
+	if (!uart->tx_done)
+		return;
+
+	uart->tx_done = 0;
+
+	if (uart->port.x_char) {
+		UART_PUT_CHAR(uart, uart->port.x_char);
+		uart->port.icount.tx++;
+		uart->port.x_char = 0;
+		uart->tx_done = 1;
+		return;
+	}
+	/*
+	 * Check the modem control lines before
+	 * transmitting anything.
+	 */
+	bfin_serial_mctrl_check(uart);
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+		bfin_serial_stop_tx(&uart->port);
+		uart->tx_done = 1;
+		return;
+	}
+
+	spin_lock_irqsave(&uart->port.lock, flags);
+	uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
+	if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
+		uart->tx_count = UART_XMIT_SIZE - xmit->tail;
+	blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
+					(unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
+	set_dma_config(uart->tx_dma_channel,
+		set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
+			INTR_ON_BUF,
+			DIMENSION_LINEAR,
+			DATA_SIZE_8));
+	set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
+	set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
+	set_dma_x_modify(uart->tx_dma_channel, 1);
+	enable_dma(uart->tx_dma_channel);
+	ier = UART_GET_IER(uart);
+	ier |= ETBEI;
+	UART_PUT_IER(uart, ier);
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static void bfin_serial_dma_rx_chars(struct bfin_serial_port * uart)
+{
+	struct tty_struct *tty = uart->port.info->tty;
+	int i, flg, status;
+
+	status = UART_GET_LSR(uart);
+	uart->port.icount.rx += CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail, UART_XMIT_SIZE);;
+
+	if (status & BI) {
+		uart->port.icount.brk++;
+		if (uart_handle_break(&uart->port))
+			goto dma_ignore_char;
+		flg = TTY_BREAK;
+	} else if (status & PE) {
+		flg = TTY_PARITY;
+		uart->port.icount.parity++;
+	} else if (status & OE) {
+		flg = TTY_OVERRUN;
+		uart->port.icount.overrun++;
+	} else if (status & FE) {
+		flg = TTY_FRAME;
+		uart->port.icount.frame++;
+	} else
+		flg = TTY_NORMAL;
+
+	for (i = uart->rx_dma_buf.head; i < uart->rx_dma_buf.tail; i++) {
+		if (uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
+			goto dma_ignore_char;
+		uart_insert_char(&uart->port, status, 2, uart->rx_dma_buf.buf[i], flg);
+	}
+dma_ignore_char:
+	tty_flip_buffer_push(tty);
+}
+
+void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
+{
+	int x_pos, pos;
+	int flags = 0;
+
+	bfin_serial_dma_tx_chars(uart);
+
+	spin_lock_irqsave(&uart->port.lock, flags);
+	x_pos = DMA_RX_XCOUNT - get_dma_curr_xcount(uart->rx_dma_channel);
+	if (x_pos == DMA_RX_XCOUNT)
+		x_pos = 0;
+
+	pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
+
+	if (pos>uart->rx_dma_buf.tail) {
+		uart->rx_dma_buf.tail = pos;
+		bfin_serial_dma_rx_chars(uart);
+		uart->rx_dma_buf.head = uart->rx_dma_buf.tail;
+	}
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+	add_timer(&(uart->rx_dma_timer));
+}
+
+static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
+{
+	struct bfin_serial_port *uart = dev_id;
+	struct circ_buf *xmit = &uart->port.info->xmit;
+	unsigned short ier;
+
+	spin_lock(&uart->port.lock);
+	if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
+		clear_dma_irqstat(uart->tx_dma_channel);
+		disable_dma(uart->tx_dma_channel);
+		ier = UART_GET_IER(uart);
+		ier &= ~ETBEI;
+		UART_PUT_IER(uart, ier);
+		xmit->tail = (xmit->tail+uart->tx_count) &(UART_XMIT_SIZE -1);
+		uart->port.icount.tx+=uart->tx_count;
+
+		if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+			uart_write_wakeup(&uart->port);
+
+		if (uart_circ_empty(xmit))
+			bfin_serial_stop_tx(&uart->port);
+		uart->tx_done = 1;
+	}
+
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
+{
+	struct bfin_serial_port *uart = dev_id;
+	unsigned short irqstat;
+
+	uart->rx_dma_nrows++;
+	if (uart->rx_dma_nrows == DMA_RX_YCOUNT) {
+		uart->rx_dma_nrows = 0;
+		uart->rx_dma_buf.tail = DMA_RX_XCOUNT*DMA_RX_YCOUNT;
+		bfin_serial_dma_rx_chars(uart);
+		uart->rx_dma_buf.head = uart->rx_dma_buf.tail = 0;
+	}
+	spin_lock(&uart->port.lock);
+	irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
+	clear_dma_irqstat(uart->rx_dma_channel);
+
+	spin_unlock(&uart->port.lock);
+	return IRQ_HANDLED;
+}
+#endif
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int bfin_serial_tx_empty(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned short lsr;
+
+	lsr = UART_GET_LSR(uart);
+	if (lsr & TEMT)
+		return TIOCSER_TEMT;
+	else
+		return 0;
+}
+
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	if (uart->cts_pin < 0)
+		return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+	if (gpio_get_value(uart->cts_pin))
+		return TIOCM_DSR | TIOCM_CAR;
+	else
+#endif
+		return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	if (uart->rts_pin < 0)
+		return;
+
+	if (mctrl & TIOCM_RTS)
+		gpio_set_value(uart->rts_pin, 0);
+	else
+		gpio_set_value(uart->rts_pin, 1);
+#endif
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	unsigned int status;
+# ifdef CONFIG_SERIAL_BFIN_DMA
+	struct uart_info *info = uart->port.info;
+	struct tty_struct *tty = info->tty;
+
+	status = bfin_serial_get_mctrl(&uart->port);
+	if (!(status & TIOCM_CTS)) {
+		tty->hw_stopped = 1;
+	} else {
+		tty->hw_stopped = 0;
+	}
+# else
+	status = bfin_serial_get_mctrl(&uart->port);
+	uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+	if (!(status & TIOCM_CTS))
+		schedule_work(&uart->cts_workqueue);
+# endif
+#endif
+}
+
+/*
+ * Interrupts are always disabled.
+ */
+static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+static int bfin_serial_startup(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	dma_addr_t dma_handle;
+
+	if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
+		printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
+		return -EBUSY;
+	}
+
+	if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
+		printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
+		free_dma(uart->rx_dma_channel);
+		return -EBUSY;
+	}
+
+	set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
+	set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
+
+	uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
+	uart->rx_dma_buf.head = 0;
+	uart->rx_dma_buf.tail = 0;
+	uart->rx_dma_nrows = 0;
+
+	set_dma_config(uart->rx_dma_channel,
+		set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
+				INTR_ON_ROW, DIMENSION_2D,
+				DATA_SIZE_8));
+	set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
+	set_dma_x_modify(uart->rx_dma_channel, 1);
+	set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
+	set_dma_y_modify(uart->rx_dma_channel, 1);
+	set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
+	enable_dma(uart->rx_dma_channel);
+
+	uart->rx_dma_timer.data = (unsigned long)(uart);
+	uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
+	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+	add_timer(&(uart->rx_dma_timer));
+#else
+	if (request_irq
+	    (uart->port.irq, bfin_serial_int, IRQF_DISABLED,
+	     "BFIN_UART_RX", uart)) {
+		printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
+		return -EBUSY;
+	}
+
+	if (request_irq
+	    (uart->port.irq+1, bfin_serial_int, IRQF_DISABLED,
+	     "BFIN_UART_TX", uart)) {
+		printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
+		free_irq(uart->port.irq, uart);
+		return -EBUSY;
+	}
+#endif
+	UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+	return 0;
+}
+
+static void bfin_serial_shutdown(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	disable_dma(uart->tx_dma_channel);
+	free_dma(uart->tx_dma_channel);
+	disable_dma(uart->rx_dma_channel);
+	free_dma(uart->rx_dma_channel);
+	del_timer(&(uart->rx_dma_timer));
+#else
+	free_irq(uart->port.irq, uart);
+	free_irq(uart->port.irq+1, uart);
+#endif
+}
+
+static void
+bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
+		   struct ktermios *old)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned long flags;
+	unsigned int baud, quot;
+	unsigned short val, ier, lsr, lcr = 0;
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS8:
+		lcr = WLS(8);
+		break;
+	case CS7:
+		lcr = WLS(7);
+		break;
+	case CS6:
+		lcr = WLS(6);
+		break;
+	case CS5:
+		lcr = WLS(5);
+		break;
+	default:
+		printk(KERN_ERR "%s: word lengh not supported\n",
+			__FUNCTION__);
+	}
+
+	if (termios->c_cflag & CSTOPB)
+		lcr |= STB;
+	if (termios->c_cflag & PARENB) {
+		lcr |= PEN;
+		if (!(termios->c_cflag & PARODD))
+			lcr |= EPS;
+	}
+
+	/* These controls are not implemented for this port */
+	termios->c_iflag |= INPCK | BRKINT | PARMRK;
+	termios->c_iflag &= ~(IGNPAR | IGNBRK);
+
+	/* These controls are not implemented for this port */
+	termios->c_iflag |= INPCK | BRKINT | PARMRK;
+	termios->c_iflag &= ~(IGNPAR | IGNBRK);
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+	quot = uart_get_divisor(port, baud);
+	spin_lock_irqsave(&uart->port.lock, flags);
+
+	do {
+		lsr = UART_GET_LSR(uart);
+	} while (!(lsr & TEMT));
+
+	/* Disable UART */
+	ier = UART_GET_IER(uart);
+	UART_PUT_IER(uart, 0);
+
+	/* Set DLAB in LCR to Access DLL and DLH */
+	val = UART_GET_LCR(uart);
+	val |= DLAB;
+	UART_PUT_LCR(uart, val);
+	SSYNC();
+
+	UART_PUT_DLL(uart, quot & 0xFF);
+	SSYNC();
+	UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
+	SSYNC();
+
+	/* Clear DLAB in LCR to Access THR RBR IER */
+	val = UART_GET_LCR(uart);
+	val &= ~DLAB;
+	UART_PUT_LCR(uart, val);
+	SSYNC();
+
+	UART_PUT_LCR(uart, lcr);
+
+	/* Enable UART */
+	UART_PUT_IER(uart, ier);
+
+	val = UART_GET_GCTL(uart);
+	val |= UCEN;
+	UART_PUT_GCTL(uart, val);
+
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static const char *bfin_serial_type(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+	return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void bfin_serial_release_port(struct uart_port *port)
+{
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int bfin_serial_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void bfin_serial_config_port(struct uart_port *port, int flags)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+	if (flags & UART_CONFIG_TYPE &&
+	    bfin_serial_request_port(&uart->port) == 0)
+		uart->port.type = PORT_BFIN;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ * The only change we allow are to the flags and type, and
+ * even then only between PORT_BFIN and PORT_UNKNOWN
+ */
+static int
+bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	return 0;
+}
+
+static struct uart_ops bfin_serial_pops = {
+	.tx_empty	= bfin_serial_tx_empty,
+	.set_mctrl	= bfin_serial_set_mctrl,
+	.get_mctrl	= bfin_serial_get_mctrl,
+	.stop_tx	= bfin_serial_stop_tx,
+	.start_tx	= bfin_serial_start_tx,
+	.stop_rx	= bfin_serial_stop_rx,
+	.enable_ms	= bfin_serial_enable_ms,
+	.break_ctl	= bfin_serial_break_ctl,
+	.startup	= bfin_serial_startup,
+	.shutdown	= bfin_serial_shutdown,
+	.set_termios	= bfin_serial_set_termios,
+	.type		= bfin_serial_type,
+	.release_port	= bfin_serial_release_port,
+	.request_port	= bfin_serial_request_port,
+	.config_port	= bfin_serial_config_port,
+	.verify_port	= bfin_serial_verify_port,
+};
+
+static void __init bfin_serial_init_ports(void)
+{
+	static int first = 1;
+	int i;
+
+	if (!first)
+		return;
+	first = 0;
+
+	for (i = 0; i < nr_ports; i++) {
+		bfin_serial_ports[i].port.uartclk   = get_sclk();
+		bfin_serial_ports[i].port.ops       = &bfin_serial_pops;
+		bfin_serial_ports[i].port.line      = i;
+		bfin_serial_ports[i].port.iotype    = UPIO_MEM;
+		bfin_serial_ports[i].port.membase   =
+			(void __iomem *)bfin_serial_resource[i].uart_base_addr;
+		bfin_serial_ports[i].port.mapbase   =
+			bfin_serial_resource[i].uart_base_addr;
+		bfin_serial_ports[i].port.irq       =
+			bfin_serial_resource[i].uart_irq;
+		bfin_serial_ports[i].port.flags     = UPF_BOOT_AUTOCONF;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+		bfin_serial_ports[i].tx_done	    = 1;
+		bfin_serial_ports[i].tx_count	    = 0;
+		bfin_serial_ports[i].tx_dma_channel =
+			bfin_serial_resource[i].uart_tx_dma_channel;
+		bfin_serial_ports[i].rx_dma_channel =
+			bfin_serial_resource[i].uart_rx_dma_channel;
+		init_timer(&(bfin_serial_ports[i].rx_dma_timer));
+#else
+		INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+		bfin_serial_ports[i].cts_pin	    =
+			bfin_serial_resource[i].uart_cts_pin;
+		bfin_serial_ports[i].rts_pin	    =
+			bfin_serial_resource[i].uart_rts_pin;
+#endif
+		bfin_serial_hw_init(&bfin_serial_ports[i]);
+
+	}
+}
+
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+static void bfin_serial_console_putchar(struct uart_port *port, int ch)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	while (!(UART_GET_LSR(uart)))
+		barrier();
+	UART_PUT_CHAR(uart, ch);
+	SSYNC();
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
+{
+	struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
+	int flags = 0;
+
+	spin_lock_irqsave(&uart->port.lock, flags);
+	uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+
+}
+
+/*
+ * If the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
+ */
+static void __init
+bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
+			   int *parity, int *bits)
+{
+	unsigned short status;
+
+	status = UART_GET_IER(uart) & (ERBFI | ETBEI);
+	if (status == (ERBFI | ETBEI)) {
+		/* ok, the port was enabled */
+		unsigned short lcr, val;
+		unsigned short dlh, dll;
+
+		lcr = UART_GET_LCR(uart);
+
+		*parity = 'n';
+		if (lcr & PEN) {
+			if (lcr & EPS)
+				*parity = 'e';
+			else
+				*parity = 'o';
+		}
+		switch (lcr & 0x03) {
+			case 0:	*bits = 5; break;
+			case 1:	*bits = 6; break;
+			case 2:	*bits = 7; break;
+			case 3:	*bits = 8; break;
+		}
+		/* Set DLAB in LCR to Access DLL and DLH */
+		val = UART_GET_LCR(uart);
+		val |= DLAB;
+		UART_PUT_LCR(uart, val);
+
+		dll = UART_GET_DLL(uart);
+		dlh = UART_GET_DLH(uart);
+
+		/* Clear DLAB in LCR to Access THR RBR IER */
+		val = UART_GET_LCR(uart);
+		val &= ~DLAB;
+		UART_PUT_LCR(uart, val);
+
+		*baud = get_sclk() / (16*(dll | dlh << 8));
+	}
+	pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits);
+}
+
+static int __init
+bfin_serial_console_setup(struct console *co, char *options)
+{
+	struct bfin_serial_port *uart;
+	int baud = 57600;
+	int bits = 8;
+	int parity = 'n';
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int flow = 'r';
+#else
+	int flow = 'n';
+#endif
+
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	if (co->index == -1 || co->index >= nr_ports)
+		co->index = 0;
+	uart = &bfin_serial_ports[co->index];
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else
+		bfin_serial_console_get_options(uart, &baud, &parity, &bits);
+
+	return uart_set_options(&uart->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bfin_serial_reg;
+static struct console bfin_serial_console = {
+	.name		= BFIN_SERIAL_NAME,
+	.write		= bfin_serial_console_write,
+	.device		= uart_console_device,
+	.setup		= bfin_serial_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &bfin_serial_reg,
+};
+
+static int __init bfin_serial_rs_console_init(void)
+{
+	bfin_serial_init_ports();
+	register_console(&bfin_serial_console);
+	return 0;
+}
+console_initcall(bfin_serial_rs_console_init);
+
+#define BFIN_SERIAL_CONSOLE	&bfin_serial_console
+#else
+#define BFIN_SERIAL_CONSOLE	NULL
+#endif
+
+static struct uart_driver bfin_serial_reg = {
+	.owner			= THIS_MODULE,
+	.driver_name		= "bfin-uart",
+	.dev_name		= BFIN_SERIAL_NAME,
+	.major			= BFIN_SERIAL_MAJOR,
+	.minor			= BFIN_SERIAL_MINOR,
+	.nr			= NR_PORTS,
+	.cons			= BFIN_SERIAL_CONSOLE,
+};
+
+static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+	if (uart)
+		uart_suspend_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static int bfin_serial_resume(struct platform_device *dev)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+	if (uart)
+		uart_resume_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static int bfin_serial_probe(struct platform_device *dev)
+{
+	struct resource *res = dev->resource;
+	int i;
+
+	for (i = 0; i < dev->num_resources; i++, res++)
+		if (res->flags & IORESOURCE_MEM)
+			break;
+
+	if (i < dev->num_resources) {
+		for (i = 0; i < nr_ports; i++, res++) {
+			if (bfin_serial_ports[i].port.mapbase != res->start)
+				continue;
+			bfin_serial_ports[i].port.dev = &dev->dev;
+			uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+			platform_set_drvdata(dev, &bfin_serial_ports[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int bfin_serial_remove(struct platform_device *pdev)
+{
+	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
+
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	gpio_free(uart->cts_pin);
+	gpio_free(uart->rts_pin);
+#endif
+
+	platform_set_drvdata(pdev, NULL);
+
+	if (uart)
+		uart_remove_one_port(&bfin_serial_reg, &uart->port);
+
+	return 0;
+}
+
+static struct platform_driver bfin_serial_driver = {
+	.probe		= bfin_serial_probe,
+	.remove		= bfin_serial_remove,
+	.suspend	= bfin_serial_suspend,
+	.resume		= bfin_serial_resume,
+	.driver		= {
+		.name	= "bfin-uart",
+	},
+};
+
+static int __init bfin_serial_init(void)
+{
+	int ret;
+
+	pr_info("Serial: Blackfin serial driver\n");
+
+	bfin_serial_init_ports();
+
+	ret = uart_register_driver(&bfin_serial_reg);
+	if (ret == 0) {
+		ret = platform_driver_register(&bfin_serial_driver);
+		if (ret) {
+			pr_debug("uart register failed\n");
+			uart_unregister_driver(&bfin_serial_reg);
+		}
+	}
+	return ret;
+}
+
+static void __exit bfin_serial_exit(void)
+{
+	platform_driver_unregister(&bfin_serial_driver);
+	uart_unregister_driver(&bfin_serial_reg);
+}
+
+module_init(bfin_serial_init);
+module_exit(bfin_serial_exit);
+
+MODULE_AUTHOR("Aubrey.Li <aubrey.li@analog.com>");
+MODULE_DESCRIPTION("Blackfin generic serial port driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h
deleted file mode 100644
index 4a23340663aa..000000000000
--- a/drivers/serial/crisv10.h
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * serial.h: Arch-dep definitions for the Etrax100 serial driver.
- *
- * Copyright (C) 1998, 1999, 2000 Axis Communications AB
- */
-
-#ifndef _ETRAX_SERIAL_H
-#define _ETRAX_SERIAL_H
-
-#include <linux/circ_buf.h>
-#include <asm/termios.h>
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-#define SERIAL_RECV_DESCRIPTORS 8
-
-struct etrax_recv_buffer {
-	struct etrax_recv_buffer *next;
-	unsigned short length;
-	unsigned char error;
-	unsigned char pad;
-
-	unsigned char buffer[0];
-};
-
-struct e100_serial {
-	int			baud;
-	volatile u8		*port; /* R_SERIALx_CTRL */
-	u32			irq;  /* bitnr in R_IRQ_MASK2 for dmaX_descr */
-
-	/* Output registers */
-	volatile u8		*oclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32		*ofirstadr;   /* adr to R_DMA_CHx_FIRST */
-	volatile u8		*ocmdadr;     /* adr to R_DMA_CHx_CMD */
-	const volatile u8	*ostatusadr;  /* adr to R_DMA_CHx_STATUS */
-
-	/* Input registers */
-	volatile u8		*iclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32		*ifirstadr;   /* adr to R_DMA_CHx_FIRST */
-	volatile u8		*icmdadr;     /* adr to R_DMA_CHx_CMD */
-	volatile u32		*idescradr;   /* adr to R_DMA_CHx_DESCR */
-
-	int			flags;	/* defined in tty.h */
-
-	u8			rx_ctrl; /* shadow for R_SERIALx_REC_CTRL */
-	u8			tx_ctrl; /* shadow for R_SERIALx_TR_CTRL */
-	u8			iseteop; /* bit number for R_SET_EOP for the input dma */
-	int			enabled; /* Set to 1 if the port is enabled in HW config */
-
-	u8		dma_out_enabled:1; /* Set to 1 if DMA should be used */
-	u8		dma_in_enabled:1;  /* Set to 1 if DMA should be used */
-
-	/* end of fields defined in rs_table[] in .c-file */
-	u8		uses_dma_in;  /* Set to 1 if DMA is used */
-	u8		uses_dma_out; /* Set to 1 if DMA is used */
-	u8		forced_eop;   /* a fifo eop has been forced */
-	int			baud_base;     /* For special baudrates */
-	int			custom_divisor; /* For special baudrates */
-	struct etrax_dma_descr	tr_descr;
-	struct etrax_dma_descr	rec_descr[SERIAL_RECV_DESCRIPTORS];
-	int			cur_rec_descr;
-
-	volatile int		tr_running; /* 1 if output is running */
-
-	struct tty_struct	*tty;
-	int			read_status_mask;
-	int			ignore_status_mask;
-	int			x_char;	/* xon/xoff character */
-	int			close_delay;
-	unsigned short		closing_wait;
-	unsigned short		closing_wait2;
-	unsigned long		event;
-	unsigned long		last_active;
-	int			line;
-	int			type;  /* PORT_ETRAX */
-	int			count;	    /* # of fd on device */
-	int			blocked_open; /* # of blocked opens */
-	struct circ_buf		xmit;
-	struct etrax_recv_buffer *first_recv_buffer;
-	struct etrax_recv_buffer *last_recv_buffer;
-	unsigned int		recv_cnt;
-	unsigned int		max_recv_cnt;
-
-	struct work_struct	work;
-	struct async_icount	icount;   /* error-statistics etc.*/
-	struct ktermios		normal_termios;
-	struct ktermios		callout_termios;
-#ifdef DECLARE_WAITQUEUE
-	wait_queue_head_t	open_wait;
-	wait_queue_head_t	close_wait;
-#else
-	struct wait_queue	*open_wait;
-	struct wait_queue	*close_wait;
-#endif
-
-	unsigned long		char_time_usec;       /* The time for 1 char, in usecs */
-	unsigned long		flush_time_usec;      /* How often we should flush */
-	unsigned long		last_tx_active_usec;  /* Last tx usec in the jiffies */
-	unsigned long		last_tx_active;       /* Last tx time in jiffies */
-	unsigned long		last_rx_active_usec;  /* Last rx usec in the jiffies */
-	unsigned long		last_rx_active;       /* Last rx time in jiffies */
-
-	int			break_detected_cnt;
-	int			errorcode;
-
-#ifdef CONFIG_ETRAX_RS485
-	struct rs485_control	rs485;  /* RS-485 support */
-#endif
-};
-
-/* this PORT is not in the standard serial.h. it's not actually used for
- * anything since we only have one type of async serial-port anyway in this
- * system.
- */
-
-#define PORT_ETRAX 1
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP	0
-
-#endif /* __KERNEL__ */
-
-#endif /* !_ETRAX_SERIAL_H */
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 04cc88cc528c..e42faa4e4282 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -46,6 +46,122 @@
 #include <asm/hardware.h>
 #include <asm/arch/imx-uart.h>
 
+/* Register definitions */
+#define URXD0 0x0  /* Receiver Register */
+#define URTX0 0x40 /* Transmitter Register */
+#define UCR1  0x80 /* Control Register 1 */
+#define UCR2  0x84 /* Control Register 2 */
+#define UCR3  0x88 /* Control Register 3 */
+#define UCR4  0x8c /* Control Register 4 */
+#define UFCR  0x90 /* FIFO Control Register */
+#define USR1  0x94 /* Status Register 1 */
+#define USR2  0x98 /* Status Register 2 */
+#define UESC  0x9c /* Escape Character Register */
+#define UTIM  0xa0 /* Escape Timer Register */
+#define UBIR  0xa4 /* BRM Incremental Register */
+#define UBMR  0xa8 /* BRM Modulator Register */
+#define UBRC  0xac /* Baud Rate Count Register */
+#define BIPR1 0xb0 /* Incremental Preset Register 1 */
+#define BIPR2 0xb4 /* Incremental Preset Register 2 */
+#define BIPR3 0xb8 /* Incremental Preset Register 3 */
+#define BIPR4 0xbc /* Incremental Preset Register 4 */
+#define BMPR1 0xc0 /* BRM Modulator Register 1 */
+#define BMPR2 0xc4 /* BRM Modulator Register 2 */
+#define BMPR3 0xc8 /* BRM Modulator Register 3 */
+#define BMPR4 0xcc /* BRM Modulator Register 4 */
+#define UTS   0xd0 /* UART Test Register */
+
+/* UART Control Register Bit Fields.*/
+#define  URXD_CHARRDY    (1<<15)
+#define  URXD_ERR        (1<<14)
+#define  URXD_OVRRUN     (1<<13)
+#define  URXD_FRMERR     (1<<12)
+#define  URXD_BRK        (1<<11)
+#define  URXD_PRERR      (1<<10)
+#define  UCR1_ADEN       (1<<15) /* Auto dectect interrupt */
+#define  UCR1_ADBR       (1<<14) /* Auto detect baud rate */
+#define  UCR1_TRDYEN     (1<<13) /* Transmitter ready interrupt enable */
+#define  UCR1_IDEN       (1<<12) /* Idle condition interrupt */
+#define  UCR1_RRDYEN     (1<<9)	 /* Recv ready interrupt enable */
+#define  UCR1_RDMAEN     (1<<8)	 /* Recv ready DMA enable */
+#define  UCR1_IREN       (1<<7)	 /* Infrared interface enable */
+#define  UCR1_TXMPTYEN   (1<<6)	 /* Transimitter empty interrupt enable */
+#define  UCR1_RTSDEN     (1<<5)	 /* RTS delta interrupt enable */
+#define  UCR1_SNDBRK     (1<<4)	 /* Send break */
+#define  UCR1_TDMAEN     (1<<3)	 /* Transmitter ready DMA enable */
+#define  UCR1_UARTCLKEN  (1<<2)	 /* UART clock enabled */
+#define  UCR1_DOZE       (1<<1)	 /* Doze */
+#define  UCR1_UARTEN     (1<<0)	 /* UART enabled */
+#define  UCR2_ESCI     	 (1<<15) /* Escape seq interrupt enable */
+#define  UCR2_IRTS  	 (1<<14) /* Ignore RTS pin */
+#define  UCR2_CTSC  	 (1<<13) /* CTS pin control */
+#define  UCR2_CTS        (1<<12) /* Clear to send */
+#define  UCR2_ESCEN      (1<<11) /* Escape enable */
+#define  UCR2_PREN       (1<<8)  /* Parity enable */
+#define  UCR2_PROE       (1<<7)  /* Parity odd/even */
+#define  UCR2_STPB       (1<<6)	 /* Stop */
+#define  UCR2_WS         (1<<5)	 /* Word size */
+#define  UCR2_RTSEN      (1<<4)	 /* Request to send interrupt enable */
+#define  UCR2_TXEN       (1<<2)	 /* Transmitter enabled */
+#define  UCR2_RXEN       (1<<1)	 /* Receiver enabled */
+#define  UCR2_SRST 	 (1<<0)	 /* SW reset */
+#define  UCR3_DTREN 	 (1<<13) /* DTR interrupt enable */
+#define  UCR3_PARERREN   (1<<12) /* Parity enable */
+#define  UCR3_FRAERREN   (1<<11) /* Frame error interrupt enable */
+#define  UCR3_DSR        (1<<10) /* Data set ready */
+#define  UCR3_DCD        (1<<9)  /* Data carrier detect */
+#define  UCR3_RI         (1<<8)  /* Ring indicator */
+#define  UCR3_TIMEOUTEN  (1<<7)  /* Timeout interrupt enable */
+#define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
+#define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
+#define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
+#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz */
+#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz */
+#define  UCR3_INVT  	 (1<<1)  /* Inverted Infrared transmission */
+#define  UCR3_BPEN  	 (1<<0)  /* Preset registers enable */
+#define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
+#define  UCR4_INVR  	 (1<<9)  /* Inverted infrared reception */
+#define  UCR4_ENIRI 	 (1<<8)  /* Serial infrared interrupt enable */
+#define  UCR4_WKEN  	 (1<<7)  /* Wake interrupt enable */
+#define  UCR4_REF16 	 (1<<6)  /* Ref freq 16 MHz */
+#define  UCR4_IRSC  	 (1<<5)  /* IR special case */
+#define  UCR4_TCEN  	 (1<<3)  /* Transmit complete interrupt enable */
+#define  UCR4_BKEN  	 (1<<2)  /* Break condition interrupt enable */
+#define  UCR4_OREN  	 (1<<1)  /* Receiver overrun interrupt enable */
+#define  UCR4_DREN  	 (1<<0)  /* Recv data ready interrupt enable */
+#define  UFCR_RXTL_SHF   0       /* Receiver trigger level shift */
+#define  UFCR_RFDIV      (7<<7)  /* Reference freq divider mask */
+#define  UFCR_TXTL_SHF   10      /* Transmitter trigger level shift */
+#define  USR1_PARITYERR  (1<<15) /* Parity error interrupt flag */
+#define  USR1_RTSS  	 (1<<14) /* RTS pin status */
+#define  USR1_TRDY  	 (1<<13) /* Transmitter ready interrupt/dma flag */
+#define  USR1_RTSD  	 (1<<12) /* RTS delta */
+#define  USR1_ESCF  	 (1<<11) /* Escape seq interrupt flag */
+#define  USR1_FRAMERR    (1<<10) /* Frame error interrupt flag */
+#define  USR1_RRDY       (1<<9)	 /* Receiver ready interrupt/dma flag */
+#define  USR1_TIMEOUT    (1<<7)	 /* Receive timeout interrupt status */
+#define  USR1_RXDS  	 (1<<6)	 /* Receiver idle interrupt flag */
+#define  USR1_AIRINT	 (1<<5)	 /* Async IR wake interrupt flag */
+#define  USR1_AWAKE 	 (1<<4)	 /* Aysnc wake interrupt flag */
+#define  USR2_ADET  	 (1<<15) /* Auto baud rate detect complete */
+#define  USR2_TXFE  	 (1<<14) /* Transmit buffer FIFO empty */
+#define  USR2_DTRF  	 (1<<13) /* DTR edge interrupt flag */
+#define  USR2_IDLE  	 (1<<12) /* Idle condition */
+#define  USR2_IRINT 	 (1<<8)	 /* Serial infrared interrupt flag */
+#define  USR2_WAKE  	 (1<<7)	 /* Wake */
+#define  USR2_RTSF  	 (1<<4)	 /* RTS edge interrupt flag */
+#define  USR2_TXDC  	 (1<<3)	 /* Transmitter complete */
+#define  USR2_BRCD  	 (1<<2)	 /* Break condition */
+#define  USR2_ORE        (1<<1)	 /* Overrun error */
+#define  USR2_RDR        (1<<0)	 /* Recv data ready */
+#define  UTS_FRCPERR	 (1<<13) /* Force parity error */
+#define  UTS_LOOP        (1<<12) /* Loop tx and rx */
+#define  UTS_TXEMPTY	 (1<<6)	 /* TxFIFO empty */
+#define  UTS_RXEMPTY	 (1<<5)	 /* RxFIFO empty */
+#define  UTS_TXFULL 	 (1<<4)	 /* TxFIFO full */
+#define  UTS_RXFULL 	 (1<<3)	 /* RxFIFO full */
+#define  UTS_SOFTRST	 (1<<0)	 /* Software reset */
+
 /* We've been assigned a range on the "Low-density serial ports" major */
 #define SERIAL_IMX_MAJOR	204
 #define MINOR_START		41
@@ -128,7 +244,10 @@ static void imx_timeout(unsigned long data)
 static void imx_stop_tx(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	UCR1((u32)sport->port.membase) &= ~UCR1_TXMPTYEN;
+	unsigned long temp;
+
+	temp = readl(sport->port.membase + UCR1);
+	writel(temp & ~UCR1_TXMPTYEN, sport->port.membase + UCR1);
 }
 
 /*
@@ -137,7 +256,10 @@ static void imx_stop_tx(struct uart_port *port)
 static void imx_stop_rx(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	UCR2((u32)sport->port.membase) &= ~UCR2_RXEN;
+	unsigned long temp;
+
+	temp = readl(sport->port.membase + UCR2);
+	writel(temp &~ UCR2_RXEN, sport->port.membase + UCR2);
 }
 
 /*
@@ -154,10 +276,10 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
 {
 	struct circ_buf *xmit = &sport->port.info->xmit;
 
-	while (!(UTS((u32)sport->port.membase) & UTS_TXFULL)) {
+	while (!(readl(sport->port.membase + UTS) & UTS_TXFULL)) {
 		/* send xmit->buf[xmit->tail]
 		 * out the port here */
-		URTX0((u32)sport->port.membase) = xmit->buf[xmit->tail];
+		writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
 		xmit->tail = (xmit->tail + 1) &
 		         (UART_XMIT_SIZE - 1);
 		sport->port.icount.tx++;
@@ -175,21 +297,24 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
 static void imx_start_tx(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
+	unsigned long temp;
 
-	UCR1((u32)sport->port.membase) |= UCR1_TXMPTYEN;
+	temp = readl(sport->port.membase + UCR1);
+	writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1);
 
-	imx_transmit_buffer(sport);
+	if (readl(sport->port.membase + UTS) & UTS_TXEMPTY)
+		imx_transmit_buffer(sport);
 }
 
 static irqreturn_t imx_rtsint(int irq, void *dev_id)
 {
 	struct imx_port *sport = (struct imx_port *)dev_id;
-	unsigned int val = USR1((u32)sport->port.membase)&USR1_RTSS;
+	unsigned int val = readl(sport->port.membase + USR1) & USR1_RTSS;
 	unsigned long flags;
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
-	USR1((u32)sport->port.membase) = USR1_RTSD;
+	writel(USR1_RTSD, sport->port.membase + USR1);
 	uart_handle_cts_change(&sport->port, !!val);
 	wake_up_interruptible(&sport->port.info->delta_msr_wait);
 
@@ -207,7 +332,7 @@ static irqreturn_t imx_txint(int irq, void *dev_id)
 	if (sport->port.x_char)
 	{
 		/* Send next char */
-		URTX0((u32)sport->port.membase) = sport->port.x_char;
+		writel(sport->port.x_char, sport->port.membase + URTX0);
 		goto out;
 	}
 
@@ -231,17 +356,18 @@ static irqreturn_t imx_rxint(int irq, void *dev_id)
 	struct imx_port *sport = dev_id;
 	unsigned int rx,flg,ignored = 0;
 	struct tty_struct *tty = sport->port.info->tty;
-	unsigned long flags;
+	unsigned long flags, temp;
 
-	rx = URXD0((u32)sport->port.membase);
+	rx = readl(sport->port.membase + URXD0);
 	spin_lock_irqsave(&sport->port.lock,flags);
 
 	do {
 		flg = TTY_NORMAL;
 		sport->port.icount.rx++;
 
-		if( USR2((u32)sport->port.membase) & USR2_BRCD ) {
-			USR2((u32)sport->port.membase) |= USR2_BRCD;
+		temp = readl(sport->port.membase + USR2);
+		if( temp & USR2_BRCD ) {
+			writel(temp | USR2_BRCD, sport->port.membase + USR2);
 			if(uart_handle_break(&sport->port))
 				goto ignore_char;
 		}
@@ -257,7 +383,7 @@ static irqreturn_t imx_rxint(int irq, void *dev_id)
 		tty_insert_flip_char(tty, rx, flg);
 
 	ignore_char:
-		rx = URXD0((u32)sport->port.membase);
+		rx = readl(sport->port.membase + URXD0);
 	} while(rx & URXD_CHARRDY);
 
 out:
@@ -301,7 +427,7 @@ static unsigned int imx_tx_empty(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
 
-	return USR2((u32)sport->port.membase) & USR2_TXDC ?  TIOCSER_TEMT : 0;
+	return (readl(sport->port.membase + USR2) & USR2_TXDC) ?  TIOCSER_TEMT : 0;
 }
 
 /*
@@ -312,10 +438,10 @@ static unsigned int imx_get_mctrl(struct uart_port *port)
         struct imx_port *sport = (struct imx_port *)port;
         unsigned int tmp = TIOCM_DSR | TIOCM_CAR;
 
-        if (USR1((u32)sport->port.membase) & USR1_RTSS)
+        if (readl(sport->port.membase + USR1) & USR1_RTSS)
                 tmp |= TIOCM_CTS;
 
-        if (UCR2((u32)sport->port.membase) & UCR2_CTS)
+        if (readl(sport->port.membase + UCR2) & UCR2_CTS)
                 tmp |= TIOCM_RTS;
 
         return tmp;
@@ -324,11 +450,14 @@ static unsigned int imx_get_mctrl(struct uart_port *port)
 static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
         struct imx_port *sport = (struct imx_port *)port;
+	unsigned long temp;
+
+	temp = readl(sport->port.membase + UCR2) & ~UCR2_CTS;
 
         if (mctrl & TIOCM_RTS)
-                UCR2((u32)sport->port.membase) |= UCR2_CTS;
-        else
-                UCR2((u32)sport->port.membase) &= ~UCR2_CTS;
+		temp |= UCR2_CTS;
+
+	writel(temp, sport->port.membase + UCR2);
 }
 
 /*
@@ -337,14 +466,16 @@ static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
 static void imx_break_ctl(struct uart_port *port, int break_state)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	unsigned long flags;
+	unsigned long flags, temp;
 
 	spin_lock_irqsave(&sport->port.lock, flags);
 
+	temp = readl(sport->port.membase + UCR1) & ~UCR1_SNDBRK;
+
 	if ( break_state != 0 )
-		UCR1((u32)sport->port.membase) |= UCR1_SNDBRK;
-	else
-		UCR1((u32)sport->port.membase) &= ~UCR1_SNDBRK;
+		temp |= UCR1_SNDBRK;
+
+	writel(temp, sport->port.membase + UCR1);
 
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
@@ -360,7 +491,7 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
 	/* set receiver / transmitter trigger level.
 	 * RFDIV is set such way to satisfy requested uartclk value
 	 */
-	val = TXTL<<10 | RXTL;
+	val = TXTL << 10 | RXTL;
 	ufcr_rfdiv = (imx_get_perclk1() + sport->port.uartclk / 2) / sport->port.uartclk;
 
 	if(!ufcr_rfdiv)
@@ -373,7 +504,7 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
 
 	val |= UFCR_RFDIV & (ufcr_rfdiv << 7);
 
-	UFCR((u32)sport->port.membase) = val;
+	writel(val, sport->port.membase + UFCR);
 
 	return 0;
 }
@@ -382,14 +513,15 @@ static int imx_startup(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
 	int retval;
-	unsigned long flags;
+	unsigned long flags, temp;
 
 	imx_setup_ufcr(sport, 0);
 
 	/* disable the DREN bit (Data Ready interrupt enable) before
 	 * requesting IRQs
 	 */
-	UCR4((u32)sport->port.membase) &= ~UCR4_DREN;
+	temp = readl(sport->port.membase + UCR4);
+	writel(temp & ~UCR4_DREN, sport->port.membase + UCR4);
 
 	/*
 	 * Allocate the IRQ
@@ -411,12 +543,16 @@ static int imx_startup(struct uart_port *port)
 	/*
 	 * Finally, clear and enable interrupts
 	 */
+	writel(USR1_RTSD, sport->port.membase + USR1);
+
+	temp = readl(sport->port.membase + UCR1);
+	temp |= (UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+	writel(temp, sport->port.membase + UCR1);
 
-	USR1((u32)sport->port.membase) = USR1_RTSD;
-	UCR1((u32)sport->port.membase) |=
-	                 (UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+	temp = readl(sport->port.membase + UCR2);
+	temp |= (UCR2_RXEN | UCR2_TXEN);
+	writel(temp, sport->port.membase + UCR2);
 
-	UCR2((u32)sport->port.membase) |= (UCR2_RXEN | UCR2_TXEN);
 	/*
 	 * Enable modem status interrupts
 	 */
@@ -437,6 +573,7 @@ error_out1:
 static void imx_shutdown(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
+	unsigned long temp;
 
 	/*
 	 * Stop our timer.
@@ -454,8 +591,9 @@ static void imx_shutdown(struct uart_port *port)
 	 * Disable all interrupts, port and break condition.
 	 */
 
-	UCR1((u32)sport->port.membase) &=
-	                 ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+	temp = readl(sport->port.membase + UCR1);
+	temp &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+	writel(temp, sport->port.membase + UCR1);
 }
 
 static void
@@ -548,18 +686,18 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
 	/*
 	 * disable interrupts and drain transmitter
 	 */
-	old_ucr1 = UCR1((u32)sport->port.membase);
-	UCR1((u32)sport->port.membase) &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
+	old_ucr1 = readl(sport->port.membase + UCR1);
+	writel(old_ucr1 & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
+			sport->port.membase + UCR1);
 
-	while ( !(USR2((u32)sport->port.membase) & USR2_TXDC))
+	while ( !(readl(sport->port.membase + USR2) & USR2_TXDC))
 		barrier();
 
 	/* then, disable everything */
-	old_txrxen = UCR2((u32)sport->port.membase) & ( UCR2_TXEN | UCR2_RXEN );
-	UCR2((u32)sport->port.membase) &= ~( UCR2_TXEN | UCR2_RXEN);
-
-	/* set the parity, stop bits and data size */
-	UCR2((u32)sport->port.membase) = ucr2;
+	old_txrxen = readl(sport->port.membase + UCR2);
+	writel(old_txrxen & ~( UCR2_TXEN | UCR2_RXEN),
+			sport->port.membase + UCR2);
+	old_txrxen &= (UCR2_TXEN | UCR2_RXEN);
 
 	/* set the baud rate. We assume uartclk = 16 MHz
 	 *
@@ -567,11 +705,13 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
 	 * --------- = --------
 	 *  uartclk    UBMR - 1
 	 */
-	UBIR((u32)sport->port.membase) = (baud / 100) - 1;
-	UBMR((u32)sport->port.membase) = 10000 - 1;
+	writel((baud / 100) - 1, sport->port.membase + UBIR);
+	writel(10000 - 1, sport->port.membase + UBMR);
+
+	writel(old_ucr1, sport->port.membase + UCR1);
 
-	UCR1((u32)sport->port.membase) = old_ucr1;
-	UCR2((u32)sport->port.membase) |= old_txrxen;
+	/* set the parity, stop bits and data size */
+	writel(ucr2 | old_txrxen, sport->port.membase + UCR2);
 
 	if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
 		imx_enable_ms(&sport->port);
@@ -730,9 +870,11 @@ static void __init imx_init_ports(void)
 static void imx_console_putchar(struct uart_port *port, int ch)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	while ((UTS((u32)sport->port.membase) & UTS_TXFULL))
+
+	while (readl(sport->port.membase + UTS) & UTS_TXFULL)
 		barrier();
-	URTX0((u32)sport->port.membase) = ch;
+
+	writel(ch, sport->port.membase + URTX0);
 }
 
 /*
@@ -747,13 +889,14 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
 	/*
 	 *	First, save UCR1/2 and then disable interrupts
 	 */
-	old_ucr1 = UCR1((u32)sport->port.membase);
-	old_ucr2 = UCR2((u32)sport->port.membase);
+	old_ucr1 = readl(sport->port.membase + UCR1);
+	old_ucr2 = readl(sport->port.membase + UCR2);
 
-	UCR1((u32)sport->port.membase) =
-	                   (old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN)
-	                   & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
-	UCR2((u32)sport->port.membase) = old_ucr2 | UCR2_TXEN;
+	writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) &
+		~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
+		sport->port.membase + UCR1);
+
+	writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2);
 
 	uart_console_write(&sport->port, s, count, imx_console_putchar);
 
@@ -761,10 +904,10 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
 	 *	Finally, wait for transmitter to become empty
 	 *	and restore UCR1/2
 	 */
-	while (!(USR2((u32)sport->port.membase) & USR2_TXDC));
+	while (!(readl(sport->port.membase + USR2) & USR2_TXDC));
 
-	UCR1((u32)sport->port.membase) = old_ucr1;
-	UCR2((u32)sport->port.membase) = old_ucr2;
+	writel(old_ucr1, sport->port.membase + UCR1);
+	writel(old_ucr2, sport->port.membase + UCR2);
 }
 
 /*
@@ -776,13 +919,13 @@ imx_console_get_options(struct imx_port *sport, int *baud,
 			   int *parity, int *bits)
 {
 
-	if ( UCR1((u32)sport->port.membase) | UCR1_UARTEN ) {
+	if ( readl(sport->port.membase + UCR1) | UCR1_UARTEN ) {
 		/* ok, the port was enabled */
 		unsigned int ucr2, ubir,ubmr, uartclk;
 		unsigned int baud_raw;
 		unsigned int ucfr_rfdiv;
 
-		ucr2 = UCR2((u32)sport->port.membase);
+		ucr2 = readl(sport->port.membase + UCR2);
 
 		*parity = 'n';
 		if (ucr2 & UCR2_PREN) {
@@ -797,11 +940,10 @@ imx_console_get_options(struct imx_port *sport, int *baud,
 		else
 			*bits = 7;
 
-		ubir = UBIR((u32)sport->port.membase) & 0xffff;
-		ubmr = UBMR((u32)sport->port.membase) & 0xffff;
-
+		ubir = readl(sport->port.membase + UBIR) & 0xffff;
+		ubmr = readl(sport->port.membase + UBMR) & 0xffff;
 
-		ucfr_rfdiv = (UFCR((u32)sport->port.membase) & UFCR_RFDIV) >> 7;
+		ucfr_rfdiv = (readl(sport->port.membase + UFCR) & UFCR_RFDIV) >> 7;
 		if (ucfr_rfdiv == 6)
 			ucfr_rfdiv = 7;
 		else
diff --git a/drivers/serial/mpsc.c b/drivers/serial/mpsc.c
index 3d2fcc57b1ce..d09f2097d5b0 100644
--- a/drivers/serial/mpsc.c
+++ b/drivers/serial/mpsc.c
@@ -183,6 +183,7 @@ struct mpsc_port_info {
 	u8 *txb_p;		/* Phys addr of txb */
 	int txr_head;		/* Where new data goes */
 	int txr_tail;		/* Where sent data comes off */
+	spinlock_t tx_lock;	/* transmit lock */
 
 	/* Mirrored values of regs we can't read (if 'mirror_regs' set) */
 	u32 MPSC_MPCR_m;
@@ -1212,6 +1213,9 @@ mpsc_tx_intr(struct mpsc_port_info *pi)
 {
 	struct mpsc_tx_desc *txre;
 	int rc = 0;
+	unsigned long iflags;
+
+	spin_lock_irqsave(&pi->tx_lock, iflags);
 
 	if (!mpsc_sdma_tx_active(pi)) {
 		txre = (struct mpsc_tx_desc *)(pi->txr +
@@ -1248,6 +1252,7 @@ mpsc_tx_intr(struct mpsc_port_info *pi)
 		mpsc_sdma_start_tx(pi);	/* start next desc if ready */
 	}
 
+	spin_unlock_irqrestore(&pi->tx_lock, iflags);
 	return rc;
 }
 
@@ -1338,11 +1343,16 @@ static void
 mpsc_start_tx(struct uart_port *port)
 {
 	struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+	unsigned long iflags;
+
+	spin_lock_irqsave(&pi->tx_lock, iflags);
 
 	mpsc_unfreeze(pi);
 	mpsc_copy_tx_data(pi);
 	mpsc_sdma_start_tx(pi);
 
+	spin_unlock_irqrestore(&pi->tx_lock, iflags);
+
 	pr_debug("mpsc_start_tx[%d]\n", port->line);
 	return;
 }
@@ -1625,6 +1635,16 @@ mpsc_console_write(struct console *co, const char *s, uint count)
 	struct mpsc_port_info *pi = &mpsc_ports[co->index];
 	u8 *bp, *dp, add_cr = 0;
 	int i;
+	unsigned long iflags;
+
+	spin_lock_irqsave(&pi->tx_lock, iflags);
+
+	while (pi->txr_head != pi->txr_tail) {
+		while (mpsc_sdma_tx_active(pi))
+			udelay(100);
+		mpsc_sdma_intr_ack(pi);
+		mpsc_tx_intr(pi);
+	}
 
 	while (mpsc_sdma_tx_active(pi))
 		udelay(100);
@@ -1668,6 +1688,7 @@ mpsc_console_write(struct console *co, const char *s, uint count)
 		pi->txr_tail = (pi->txr_tail + 1) & (MPSC_TXR_ENTRIES - 1);
 	}
 
+	spin_unlock_irqrestore(&pi->tx_lock, iflags);
 	return;
 }
 
@@ -2005,7 +2026,8 @@ mpsc_drv_probe(struct platform_device *dev)
 		if (!(rc = mpsc_drv_map_regs(pi, dev))) {
 			mpsc_drv_get_platform_data(pi, dev, dev->id);
 
-			if (!(rc = mpsc_make_ready(pi)))
+			if (!(rc = mpsc_make_ready(pi))) {
+				spin_lock_init(&pi->tx_lock);
 				if (!(rc = uart_add_one_port(&mpsc_reg,
 					&pi->port)))
 					rc = 0;
@@ -2014,6 +2036,7 @@ mpsc_drv_probe(struct platform_device *dev)
 						(struct uart_port *)pi);
 					mpsc_drv_unmap_regs(pi);
 				}
+			}
 			else
 				mpsc_drv_unmap_regs(pi);
 		}
diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c
index e7928fee833a..7ffdaeaf0545 100644
--- a/drivers/serial/of_serial.c
+++ b/drivers/serial/of_serial.c
@@ -48,7 +48,8 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev,
 	port->iotype = UPIO_MEM;
 	port->type = type;
 	port->uartclk = *clk;
-	port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+	port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
+		| UPF_FIXED_PORT;
 	port->dev = &ofdev->dev;
 	port->custom_divisor = *clk / (16 * (*spd));
 
diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c
index d403aaa55092..e9c6cb391a23 100644
--- a/drivers/serial/pxa.c
+++ b/drivers/serial/pxa.c
@@ -717,7 +717,7 @@ struct uart_ops serial_pxa_pops = {
 static struct uart_pxa_port serial_pxa_ports[] = {
      {	/* FFUART */
 	.name	= "FFUART",
-	.cken	= CKEN6_FFUART,
+	.cken	= CKEN_FFUART,
 	.port	= {
 		.type		= PORT_PXA,
 		.iotype		= UPIO_MEM,
@@ -731,7 +731,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
 	},
   }, {	/* BTUART */
 	.name	= "BTUART",
-	.cken	= CKEN7_BTUART,
+	.cken	= CKEN_BTUART,
 	.port	= {
 		.type		= PORT_PXA,
 		.iotype		= UPIO_MEM,
@@ -745,7 +745,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
 	},
   }, {	/* STUART */
 	.name	= "STUART",
-	.cken	= CKEN5_STUART,
+	.cken	= CKEN_STUART,
 	.port	= {
 		.type		= PORT_PXA,
 		.iotype		= UPIO_MEM,
@@ -759,7 +759,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
 	},
   }, {  /* HWUART */
 	.name	= "HWUART",
-	.cken	= CKEN4_HWUART,
+	.cken	= CKEN_HWUART,
 	.port = {
 		.type		= PORT_PXA,
 		.iotype		= UPIO_MEM,
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index 0422c0f1f852..326020f86f75 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -37,13 +37,6 @@
 #include <asm/irq.h>
 #include <asm/uaccess.h>
 
-#undef	DEBUG
-#ifdef DEBUG
-#define DPRINTK(x...)	printk(x)
-#else
-#define DPRINTK(x...)	do { } while (0)
-#endif
-
 /*
  * This is used to lock changes in serial line configuration.
  */
@@ -552,7 +545,7 @@ static void uart_flush_buffer(struct tty_struct *tty)
 		return;
 	}
 
-	DPRINTK("uart_flush_buffer(%d) called\n", tty->index);
+	pr_debug("uart_flush_buffer(%d) called\n", tty->index);
 
 	spin_lock_irqsave(&port->lock, flags);
 	uart_circ_clear(&state->info->xmit);
@@ -672,19 +665,21 @@ static int uart_set_info(struct uart_state *state,
 	 */
 	mutex_lock(&state->mutex);
 
-	change_irq  = new_serial.irq != port->irq;
+	change_irq  = !(port->flags & UPF_FIXED_PORT)
+		&& new_serial.irq != port->irq;
 
 	/*
 	 * Since changing the 'type' of the port changes its resource
 	 * allocations, we should treat type changes the same as
 	 * IO port changes.
 	 */
-	change_port = new_port != port->iobase ||
-		      (unsigned long)new_serial.iomem_base != port->mapbase ||
-		      new_serial.hub6 != port->hub6 ||
-		      new_serial.io_type != port->iotype ||
-		      new_serial.iomem_reg_shift != port->regshift ||
-		      new_serial.type != port->type;
+	change_port = !(port->flags & UPF_FIXED_PORT)
+		&& (new_port != port->iobase ||
+		    (unsigned long)new_serial.iomem_base != port->mapbase ||
+		    new_serial.hub6 != port->hub6 ||
+		    new_serial.io_type != port->iotype ||
+		    new_serial.iomem_reg_shift != port->regshift ||
+		    new_serial.type != port->type);
 
 	old_flags = port->flags;
 	new_flags = new_serial.flags;
@@ -796,8 +791,10 @@ static int uart_set_info(struct uart_state *state,
 		}
 	}
 
-	port->irq              = new_serial.irq;
-	port->uartclk          = new_serial.baud_base * 16;
+	if (change_irq)
+		port->irq      = new_serial.irq;
+	if (!(port->flags & UPF_FIXED_PORT))
+		port->uartclk  = new_serial.baud_base * 16;
 	port->flags            = (port->flags & ~UPF_CHANGE_MASK) |
 				 (new_flags & UPF_CHANGE_MASK);
 	port->custom_divisor   = new_serial.custom_divisor;
@@ -1220,7 +1217,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 
 	port = state->port;
 
-	DPRINTK("uart_close(%d) called\n", port->line);
+	pr_debug("uart_close(%d) called\n", port->line);
 
 	mutex_lock(&state->mutex);
 
@@ -1339,7 +1336,7 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
 
 	expire = jiffies + timeout;
 
-	DPRINTK("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n",
+	pr_debug("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n",
 	        port->line, jiffies, expire);
 
 	/*
@@ -1368,7 +1365,7 @@ static void uart_hangup(struct tty_struct *tty)
 	struct uart_state *state = tty->driver_data;
 
 	BUG_ON(!kernel_locked());
-	DPRINTK("uart_hangup(%d)\n", state->port->line);
+	pr_debug("uart_hangup(%d)\n", state->port->line);
 
 	mutex_lock(&state->mutex);
 	if (state->info && state->info->flags & UIF_NORMAL_ACTIVE) {
@@ -1566,7 +1563,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	int retval, line = tty->index;
 
 	BUG_ON(!kernel_locked());
-	DPRINTK("uart_open(%d) called\n", line);
+	pr_debug("uart_open(%d) called\n", line);
 
 	/*
 	 * tty->driver->num won't change, so we won't fail here with
@@ -2064,6 +2061,7 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 	case UPIO_MEM32:
 	case UPIO_AU:
 	case UPIO_TSI:
+	case UPIO_DWAPB:
 		snprintf(address, sizeof(address),
 			 "MMIO 0x%lx", port->mapbase);
 		break;
@@ -2409,6 +2407,7 @@ int uart_match_port(struct uart_port *port1, struct uart_port *port2)
 	case UPIO_MEM32:
 	case UPIO_AU:
 	case UPIO_TSI:
+	case UPIO_DWAPB:
 		return (port1->mapbase == port2->mapbase);
 	}
 	return 0;
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index 46c40bbc4bc6..1f89496d530e 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -46,6 +46,7 @@
 #endif
 
 #if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#include <linux/ctype.h>
 #include <asm/clock.h>
 #include <asm/sh_bios.h>
 #include <asm/kgdb.h>
@@ -61,7 +62,7 @@ struct sci_port {
 	unsigned int		type;
 
 	/* Port IRQs: ERI, RXI, TXI, BRI (optional) */
-	unsigned int		irqs[SCIx_NR_IRQS]; 
+	unsigned int		irqs[SCIx_NR_IRQS];
 
 	/* Port pin configuration */
 	void			(*init_pins)(struct uart_port *port,
@@ -76,6 +77,11 @@ struct sci_port {
 	/* Break timer */
 	struct timer_list	break_timer;
 	int			break_flag;
+
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+	/* Port clock */
+	struct clk		*clk;
+#endif
 };
 
 #ifdef CONFIG_SH_KGDB
@@ -163,7 +169,7 @@ static void put_string(struct sci_port *sci_port, const char *buffer, int count)
 	usegdb |= sh_bios_in_gdb_mode();
 #endif
 #ifdef CONFIG_SH_KGDB
-	usegdb |= (kgdb_in_gdb_mode && (port == kgdb_sci_port));
+	usegdb |= (kgdb_in_gdb_mode && (sci_port == kgdb_sci_port));
 #endif
 
 	if (usegdb) {
@@ -204,7 +210,7 @@ static int kgdb_sci_getchar(void)
         int c;
 
         /* Keep trying to read a character, this could be neater */
-        while ((c = get_char(kgdb_sci_port)) < 0)
+        while ((c = get_char(&kgdb_sci_port->port)) < 0)
 		cpu_relax();
 
         return c;
@@ -212,7 +218,7 @@ static int kgdb_sci_getchar(void)
 
 static inline void kgdb_sci_putchar(int c)
 {
-        put_char(kgdb_sci_port, c);
+        put_char(&kgdb_sci_port->port, c);
 }
 #endif /* CONFIG_SH_KGDB */
 
@@ -283,12 +289,23 @@ static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
 #endif
 
 #if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7710)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) 
 /* SH7300 doesn't use RTS/CTS */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 {
 	sci_out(port, SCFCR, 0);
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
+static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag)
+{
+	unsigned int fcr_val = 0;
+
+	set_sh771x_scif_pfc(port);
+	if (cflag & CRTSCTS) {
+		fcr_val |= SCFCR_MCE;
+	}
+	sci_out(port, SCFCR, fcr_val);
+}
 #elif defined(CONFIG_CPU_SH3)
 /* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
 static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
@@ -350,7 +367,7 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 	} else {
 #ifdef CONFIG_CPU_SUBTYPE_SH7343
 		/* Nothing */
-#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780) || defined(CONFIG_CPU_SUBTYPE_SH7785)
 		ctrl_outw(0x0080, SCSPTR0); /* Set RTS = 1 */
 #else
 		ctrl_outw(0x0080, SCSPTR2); /* Set RTS = 1 */
@@ -360,7 +377,9 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
 }
 #endif
 
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7785)
 static inline int scif_txroom(struct uart_port *port)
 {
 	return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
@@ -735,12 +754,6 @@ static irqreturn_t sci_br_interrupt(int irq, void *ptr)
 
 	/* Handle BREAKs */
 	sci_handle_breaks(port);
-
-#ifdef CONFIG_SH_KGDB
-	/* Break into the debugger if a break is detected */
-	BREAKPOINT();
-#endif
-
 	sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
 
 	return IRQ_HANDLED;
@@ -947,6 +960,10 @@ static int sci_startup(struct uart_port *port)
 	if (s->enable)
 		s->enable(port);
 
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+	s->clk = clk_get(NULL, "module_clk");
+#endif
+
 	sci_request_irq(s);
 	sci_start_tx(port);
 	sci_start_rx(port, 1);
@@ -964,6 +981,11 @@ static void sci_shutdown(struct uart_port *port)
 
 	if (s->disable)
 		s->disable(port);
+
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+	clk_put(s->clk);
+	s->clk = NULL;
+#endif
 }
 
 static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
@@ -971,7 +993,6 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 {
 	struct sci_port *s = &sci_ports[port->line];
 	unsigned int status, baud, smr_val;
-	unsigned long flags;
 	int t;
 
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
@@ -983,18 +1004,14 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 		default:
 		{
 #if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
-			struct clk *clk = clk_get(NULL, "module_clk");
-			t = SCBRR_VALUE(baud, clk_get_rate(clk));
-			clk_put(clk);
+			t = SCBRR_VALUE(baud, clk_get_rate(s->clk));
 #else
 			t = SCBRR_VALUE(baud);
 #endif
-		}
 			break;
+		}
 	}
 
-	spin_lock_irqsave(&port->lock, flags);
-
 	do {
 		status = sci_in(port, SCxSR);
 	} while (!(status & SCxSR_TEND(port)));
@@ -1038,8 +1055,6 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	if ((termios->c_cflag & CREAD) != 0)
               sci_start_rx(port,0);
-
-	spin_unlock_irqrestore(&port->lock, flags);
 }
 
 static const char *sci_type(struct uart_port *port)
@@ -1220,10 +1235,13 @@ static int __init serial_console_setup(struct console *co, char *options)
 	if (!port->membase || !port->mapbase)
 		return -ENODEV;
 
-	spin_lock_init(&port->lock);
-
 	port->type = serial_console_port->type;
 
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+	if (!serial_console_port->clk)
+		serial_console_port->clk = clk_get(NULL, "module_clk");
+#endif
+
 	if (port->flags & UPF_IOREMAP)
 		sci_config_port(port, 0);
 
@@ -1247,7 +1265,7 @@ static struct console serial_console = {
 	.device		= uart_console_device,
 	.write		= serial_console_write,
 	.setup		= serial_console_setup,
-	.flags		= CON_PRINTBUFFER, 
+	.flags		= CON_PRINTBUFFER,
 	.index		= -1,
 	.data		= &sci_uart_driver,
 };
@@ -1292,11 +1310,23 @@ int __init kgdb_console_setup(struct console *co, char *options)
 	int parity = 'n';
 	int flow = 'n';
 
-	spin_lock_init(&port->lock);
-
 	if (co->index != kgdb_portnum)
 		co->index = kgdb_portnum;
 
+	kgdb_sci_port = &sci_ports[co->index];
+	port = &kgdb_sci_port->port;
+
+	/*
+	 * Also need to check port->type, we don't actually have any
+	 * UPIO_PORT ports, but uart_report_port() handily misreports
+	 * it anyways if we don't have a port available by the time this is
+	 * called.
+	 */
+	if (!port->type)
+		return -ENODEV;
+	if (!port->membase || !port->mapbase)
+		return -ENODEV;
+
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 	else
@@ -1311,11 +1341,12 @@ int __init kgdb_console_setup(struct console *co, char *options)
 
 #ifdef CONFIG_SH_KGDB_CONSOLE
 static struct console kgdb_console = {
-        .name		= "ttySC",
-        .write		= kgdb_console_write,
-        .setup		= kgdb_console_setup,
-        .flags		= CON_PRINTBUFFER | CON_ENABLED,
-        .index		= -1,
+	.name		= "ttySC",
+	.device		= uart_console_device,
+	.write		= kgdb_console_write,
+	.setup		= kgdb_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
 	.data		= &sci_uart_driver,
 };
 
@@ -1361,9 +1392,19 @@ static int __devinit sci_probe(struct platform_device *dev)
 	struct plat_sci_port *p = dev->dev.platform_data;
 	int i;
 
-	for (i = 0; p && p->flags != 0 && i < SCI_NPORTS; p++, i++) {
+	for (i = 0; p && p->flags != 0; p++, i++) {
 		struct sci_port *sciport = &sci_ports[i];
 
+		/* Sanity check */
+		if (unlikely(i == SCI_NPORTS)) {
+			dev_notice(&dev->dev, "Attempting to register port "
+				   "%d when only %d are available.\n",
+				   i+1, SCI_NPORTS);
+			dev_notice(&dev->dev, "Consider bumping "
+				   "CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
+			break;
+		}
+
 		sciport->port.mapbase	= p->mapbase;
 
 		/*
@@ -1386,6 +1427,12 @@ static int __devinit sci_probe(struct platform_device *dev)
 		uart_add_one_port(&sci_uart_driver, &sciport->port);
 	}
 
+#if defined(CONFIG_SH_KGDB) && !defined(CONFIG_SH_KGDB_CONSOLE)
+	kgdb_sci_port	= &sci_ports[kgdb_portnum];
+	kgdb_getchar	= kgdb_sci_getchar;
+	kgdb_putchar	= kgdb_sci_putchar;
+#endif
+
 #ifdef CONFIG_CPU_FREQ
 	cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
 	dev_info(&dev->dev, "sci: CPU frequency notifier registered\n");
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index 77f7d6351ab1..fb04fb5f9843 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -73,9 +73,13 @@
 # define SCPDR  0xA4050136        /* 16 bit SCIF */
 # define SCSCR_INIT(port)  0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
 # define SCIF_ONLY
-#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712) 
 # define SCSPTR0 0xA4400000	  /* 16 bit SCIF */
-# define SCSCR_INIT(port)  0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
+# define SCI_NPORTS 2
+# define SCIF_ORER 0x0001   /* overrun error bit */
+# define PACR 0xa4050100
+# define PBCR 0xa4050102
+# define SCSCR_INIT(port)          0x3B
 # define SCIF_ONLY
 #elif defined(CONFIG_CPU_SUBTYPE_SH73180)
 # define SCPDR  0xA4050138        /* 16 bit SCIF */
@@ -140,6 +144,16 @@
 # define SCIF_ORER	0x0001		/* Overrun error bit */
 # define SCSCR_INIT(port)	0x3a	/* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
 # define SCIF_ONLY
+#elif defined(CONFIG_CPU_SUBTYPE_SH7785)
+# define SCSPTR0	0xffea0024	/* 16 bit SCIF */
+# define SCSPTR1	0xffeb0024	/* 16 bit SCIF */
+# define SCSPTR2	0xffec0024	/* 16 bit SCIF */
+# define SCSPTR3	0xffed0024	/* 16 bit SCIF */
+# define SCSPTR4	0xffee0024	/* 16 bit SCIF */
+# define SCSPTR5	0xffef0024	/* 16 bit SCIF */
+# define SCIF_OPER	0x0001		/* Overrun error bit */
+# define SCSCR_INIT(port)	0x3a	/* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+# define SCIF_ONLY
 #elif defined(CONFIG_CPU_SUBTYPE_SH7206)
 # define SCSPTR0 0xfffe8020 /* 16 bit SCIF */
 # define SCSPTR1 0xfffe8820 /* 16 bit SCIF */
@@ -163,7 +177,10 @@
 #define SCI_CTRL_FLAGS_RIE  0x40 /* all */
 #define SCI_CTRL_FLAGS_TE   0x20 /* all */
 #define SCI_CTRL_FLAGS_RE   0x10 /* all */
-#if defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7750) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7751) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7785)
 #define SCI_CTRL_FLAGS_REIE 0x08 /* 7750 SCIF */
 #else
 #define SCI_CTRL_FLAGS_REIE 0
@@ -333,9 +350,15 @@
   }
 
 #ifdef CONFIG_CPU_SH3
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
-    defined(CONFIG_CPU_SUBTYPE_SH7705) || \
-    defined(CONFIG_CPU_SUBTYPE_SH7710)
+#if defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
+#define SCIx_FNS(name, sh3_sci_offset, sh3_sci_size, sh4_sci_offset, sh4_sci_size, \
+		                sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size, \
+		                 h8_sci_offset, h8_sci_size) \
+  CPU_SCIx_FNS(name, sh4_sci_offset, sh4_sci_size, sh4_scif_offset, sh4_scif_size)
+#define SCIF_FNS(name, sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size) \
+	  CPU_SCIF_FNS(name, sh4_scif_offset, sh4_scif_size)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7705) 
 #define SCIF_FNS(name, scif_offset, scif_size) \
   CPU_SCIF_FNS(name, scif_offset, scif_size)
 #else
@@ -362,8 +385,8 @@
 #endif
 
 #if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
-    defined(CONFIG_CPU_SUBTYPE_SH7705) || \
-    defined(CONFIG_CPU_SUBTYPE_SH7710)
+    defined(CONFIG_CPU_SUBTYPE_SH7705) 
+
 SCIF_FNS(SCSMR,  0x00, 16)
 SCIF_FNS(SCBRR,  0x04,  8)
 SCIF_FNS(SCSCR,  0x08, 16)
@@ -385,7 +408,9 @@ SCIx_FNS(SCxTDR, 0x06,  8, 0x0c,  8, 0x06,  8, 0x0C,  8, 0x03,  8)
 SCIx_FNS(SCxSR,  0x08,  8, 0x10,  8, 0x08, 16, 0x10, 16, 0x04,  8)
 SCIx_FNS(SCxRDR, 0x0a,  8, 0x14,  8, 0x0A,  8, 0x14,  8, 0x05,  8)
 SCIF_FNS(SCFCR,                      0x0c,  8, 0x18, 16)
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7785)
 SCIF_FNS(SCFDR,			     0x0e, 16, 0x1C, 16)
 SCIF_FNS(SCTFDR,		     0x0e, 16, 0x1C, 16)
 SCIF_FNS(SCRFDR,		     0x0e, 16, 0x20, 16)
@@ -471,13 +496,24 @@ static inline int sci_rxd_in(struct uart_port *port)
 		return ctrl_inb(SCPDR)&0x10 ? 1 : 0; /* SCIF */
 	return 1;
 }
-#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
 static inline int sci_rxd_in(struct uart_port *port)
 {
-	if (port->mapbase == SCSPTR0)
-		return ctrl_inw(SCSPTR0 + 0x10) & 0x01 ? 1 : 0;
-	return 1;
+	  return sci_in(port,SCxSR)&0x0010 ? 1 : 0;
+}
+static inline void set_sh771x_scif_pfc(struct uart_port *port)
+{
+	if (port->mapbase == 0xA4400000){
+		ctrl_outw(ctrl_inw(PACR)&0xffc0,PACR);
+		ctrl_outw(ctrl_inw(PBCR)&0x0fff,PBCR);
+		return;
+	}
+	if (port->mapbase == 0xA4410000){
+		ctrl_outw(ctrl_inw(PBCR)&0xf003,PBCR);
+		return;
+	}
 }
+
 #elif defined(CONFIG_CPU_SUBTYPE_SH7750) || \
       defined(CONFIG_CPU_SUBTYPE_SH7751) || \
       defined(CONFIG_CPU_SUBTYPE_SH4_202)
@@ -576,6 +612,23 @@ static inline int sci_rxd_in(struct uart_port *port)
 		return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
 	return 1;
 }
+#elif defined(CONFIG_CPU_SUBTYPE_SH7785)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+	if (port->mapbase == 0xffea0000)
+		return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffeb0000)
+		return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffec0000)
+		return ctrl_inw(SCSPTR2) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffed0000)
+		return ctrl_inw(SCSPTR3) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffee0000)
+		return ctrl_inw(SCSPTR4) & 0x0001 ? 1 : 0; /* SCIF */
+	if (port->mapbase == 0xffef0000)
+		return ctrl_inw(SCSPTR5) & 0x0001 ? 1 : 0; /* SCIF */
+	return 1;
+}
 #elif defined(CONFIG_CPU_SUBTYPE_SH7206)
 static inline int sci_rxd_in(struct uart_port *port)
 {
@@ -634,7 +687,9 @@ static inline int sci_rxd_in(struct uart_port *port)
  * -- Mitch Davis - 15 Jul 2000
  */
 
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+    defined(CONFIG_CPU_SUBTYPE_SH7785)
 #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1)
 #elif defined(CONFIG_CPU_SUBTYPE_SH7705)
 #define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1)
diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c
index bfd44177a215..2a63cdba3208 100644
--- a/drivers/serial/sunsu.c
+++ b/drivers/serial/sunsu.c
@@ -1312,7 +1312,7 @@ static void sunsu_console_write(struct console *co, const char *s,
  *	- initialize the serial port
  *	Return non-zero if we didn't find a serial port.
  */
-static int sunsu_console_setup(struct console *co, char *options)
+static int __init sunsu_console_setup(struct console *co, char *options)
 {
 	struct uart_port *port;
 	int baud = 9600;
@@ -1343,7 +1343,7 @@ static int sunsu_console_setup(struct console *co, char *options)
 	return uart_set_options(port, co, baud, parity, bits, flow);
 }
 
-static struct console sunsu_cons = {
+static struct console sunsu_console = {
 	.name	=	"ttyS",
 	.write	=	sunsu_console_write,
 	.device	=	uart_console_device,
@@ -1373,9 +1373,9 @@ static inline struct console *SUNSU_CONSOLE(int num_uart)
 	if (i == num_uart)
 		return NULL;
 
-	sunsu_cons.index = i;
+	sunsu_console.index = i;
 
-	return &sunsu_cons;
+	return &sunsu_console;
 }
 #else
 #define SUNSU_CONSOLE(num_uart)		(NULL)