mfd/power: ab8500: Push data to power supply code

There is a slew of defines, structs and enums and even a
function call only relevant for the charging code that
still lives in <linux/mfd/abx500.h>. Push it down to the
"ab8500-bm.h" header in the power supply subsystem where
it is actually used.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

1 files changed, 274 insertions, 4 deletions

diff --git a/drivers/power/supply/ab8500-bm.h b/drivers/power/supply/ab8500-bm.h
index a1b31c971a45..41c69a4f2a1f 100644
--- a/drivers/power/supply/ab8500-bm.h
+++ b/drivers/power/supply/ab8500-bm.h
@@ -4,7 +4,6 @@
 #define _AB8500_CHARGER_H_
 
 #include <linux/kernel.h>
-#include <linux/mfd/abx500.h>
 
 /*
  * System control 2 register offsets.
@@ -268,6 +267,277 @@ enum bup_vch_sel {
 #define BUS_PP_PRECHG_CURRENT_MASK		0x0E
 #define BUS_POWER_PATH_PRECHG_ENA		0x01
 
+/*
+ * ADC for the battery thermistor.
+ * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
+ * with a NTC resistor to both identify the battery and to measure its
+ * temperature. Different phone manufactures uses different techniques to both
+ * identify the battery and to read its temperature.
+ */
+enum abx500_adc_therm {
+	ABx500_ADC_THERM_BATCTRL,
+	ABx500_ADC_THERM_BATTEMP,
+};
+
+/**
+ * struct abx500_res_to_temp - defines one point in a temp to res curve. To
+ * be used in battery packs that combines the identification resistor with a
+ * NTC resistor.
+ * @temp:			battery pack temperature in Celsius
+ * @resist:			NTC resistor net total resistance
+ */
+struct abx500_res_to_temp {
+	int temp;
+	int resist;
+};
+
+/**
+ * struct abx500_v_to_cap - Table for translating voltage to capacity
+ * @voltage:		Voltage in mV
+ * @capacity:		Capacity in percent
+ */
+struct abx500_v_to_cap {
+	int voltage;
+	int capacity;
+};
+
+/* Forward declaration */
+struct abx500_fg;
+
+/**
+ * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
+ * if not specified
+ * @recovery_sleep_timer:	Time between measurements while recovering
+ * @recovery_total_time:	Total recovery time
+ * @init_timer:			Measurement interval during startup
+ * @init_discard_time:		Time we discard voltage measurement at startup
+ * @init_total_time:		Total init time during startup
+ * @high_curr_time:		Time current has to be high to go to recovery
+ * @accu_charging:		FG accumulation time while charging
+ * @accu_high_curr:		FG accumulation time in high current mode
+ * @high_curr_threshold:	High current threshold, in mA
+ * @lowbat_threshold:		Low battery threshold, in mV
+ * @overbat_threshold:		Over battery threshold, in mV
+ * @battok_falling_th_sel0	Threshold in mV for battOk signal sel0
+ *				Resolution in 50 mV step.
+ * @battok_raising_th_sel1	Threshold in mV for battOk signal sel1
+ *				Resolution in 50 mV step.
+ * @user_cap_limit		Capacity reported from user must be within this
+ *				limit to be considered as sane, in percentage
+ *				points.
+ * @maint_thres			This is the threshold where we stop reporting
+ *				battery full while in maintenance, in per cent
+ * @pcut_enable:			Enable power cut feature in ab8505
+ * @pcut_max_time:		Max time threshold
+ * @pcut_flag_time:		Flagtime threshold
+ * @pcut_max_restart:		Max number of restarts
+ * @pcut_debounce_time:		Sets battery debounce time
+ */
+struct abx500_fg_parameters {
+	int recovery_sleep_timer;
+	int recovery_total_time;
+	int init_timer;
+	int init_discard_time;
+	int init_total_time;
+	int high_curr_time;
+	int accu_charging;
+	int accu_high_curr;
+	int high_curr_threshold;
+	int lowbat_threshold;
+	int overbat_threshold;
+	int battok_falling_th_sel0;
+	int battok_raising_th_sel1;
+	int user_cap_limit;
+	int maint_thres;
+	bool pcut_enable;
+	u8 pcut_max_time;
+	u8 pcut_flag_time;
+	u8 pcut_max_restart;
+	u8 pcut_debounce_time;
+};
+
+/**
+ * struct abx500_charger_maximization - struct used by the board config.
+ * @use_maxi:		Enable maximization for this battery type
+ * @maxi_chg_curr:	Maximum charger current allowed
+ * @maxi_wait_cycles:	cycles to wait before setting charger current
+ * @charger_curr_step	delta between two charger current settings (mA)
+ */
+struct abx500_maxim_parameters {
+	bool ena_maxi;
+	int chg_curr;
+	int wait_cycles;
+	int charger_curr_step;
+};
+
+/**
+ * struct abx500_battery_type - different batteries supported
+ * @name:			battery technology
+ * @resis_high:			battery upper resistance limit
+ * @resis_low:			battery lower resistance limit
+ * @charge_full_design:		Maximum battery capacity in mAh
+ * @nominal_voltage:		Nominal voltage of the battery in mV
+ * @termination_vol:		max voltage upto which battery can be charged
+ * @termination_curr		battery charging termination current in mA
+ * @recharge_cap		battery capacity limit that will trigger a new
+ *				full charging cycle in the case where maintenan-
+ *				-ce charging has been disabled
+ * @normal_cur_lvl:		charger current in normal state in mA
+ * @normal_vol_lvl:		charger voltage in normal state in mV
+ * @maint_a_cur_lvl:		charger current in maintenance A state in mA
+ * @maint_a_vol_lvl:		charger voltage in maintenance A state in mV
+ * @maint_a_chg_timer_h:	charge time in maintenance A state
+ * @maint_b_cur_lvl:		charger current in maintenance B state in mA
+ * @maint_b_vol_lvl:		charger voltage in maintenance B state in mV
+ * @maint_b_chg_timer_h:	charge time in maintenance B state
+ * @low_high_cur_lvl:		charger current in temp low/high state in mA
+ * @low_high_vol_lvl:		charger voltage in temp low/high state in mV'
+ * @battery_resistance:		battery inner resistance in mOhm.
+ * @n_r_t_tbl_elements:		number of elements in r_to_t_tbl
+ * @r_to_t_tbl:			table containing resistance to temp points
+ * @n_v_cap_tbl_elements:	number of elements in v_to_cap_tbl
+ * @v_to_cap_tbl:		Voltage to capacity (in %) table
+ * @n_batres_tbl_elements	number of elements in the batres_tbl
+ * @batres_tbl			battery internal resistance vs temperature table
+ */
+struct abx500_battery_type {
+	int name;
+	int resis_high;
+	int resis_low;
+	int charge_full_design;
+	int nominal_voltage;
+	int termination_vol;
+	int termination_curr;
+	int recharge_cap;
+	int normal_cur_lvl;
+	int normal_vol_lvl;
+	int maint_a_cur_lvl;
+	int maint_a_vol_lvl;
+	int maint_a_chg_timer_h;
+	int maint_b_cur_lvl;
+	int maint_b_vol_lvl;
+	int maint_b_chg_timer_h;
+	int low_high_cur_lvl;
+	int low_high_vol_lvl;
+	int battery_resistance;
+	int n_temp_tbl_elements;
+	const struct abx500_res_to_temp *r_to_t_tbl;
+	int n_v_cap_tbl_elements;
+	const struct abx500_v_to_cap *v_to_cap_tbl;
+	int n_batres_tbl_elements;
+	const struct batres_vs_temp *batres_tbl;
+};
+
+/**
+ * struct abx500_bm_capacity_levels - abx500 capacity level data
+ * @critical:		critical capacity level in percent
+ * @low:		low capacity level in percent
+ * @normal:		normal capacity level in percent
+ * @high:		high capacity level in percent
+ * @full:		full capacity level in percent
+ */
+struct abx500_bm_capacity_levels {
+	int critical;
+	int low;
+	int normal;
+	int high;
+	int full;
+};
+
+/**
+ * struct abx500_bm_charger_parameters - Charger specific parameters
+ * @usb_volt_max:	maximum allowed USB charger voltage in mV
+ * @usb_curr_max:	maximum allowed USB charger current in mA
+ * @ac_volt_max:	maximum allowed AC charger voltage in mV
+ * @ac_curr_max:	maximum allowed AC charger current in mA
+ */
+struct abx500_bm_charger_parameters {
+	int usb_volt_max;
+	int usb_curr_max;
+	int ac_volt_max;
+	int ac_curr_max;
+};
+
+/**
+ * struct abx500_bm_data - abx500 battery management data
+ * @temp_under		under this temp, charging is stopped
+ * @temp_low		between this temp and temp_under charging is reduced
+ * @temp_high		between this temp and temp_over charging is reduced
+ * @temp_over		over this temp, charging is stopped
+ * @temp_now		present battery temperature
+ * @temp_interval_chg	temperature measurement interval in s when charging
+ * @temp_interval_nochg	temperature measurement interval in s when not charging
+ * @main_safety_tmr_h	safety timer for main charger
+ * @usb_safety_tmr_h	safety timer for usb charger
+ * @bkup_bat_v		voltage which we charge the backup battery with
+ * @bkup_bat_i		current which we charge the backup battery with
+ * @no_maintenance	indicates that maintenance charging is disabled
+ * @capacity_scaling    indicates whether capacity scaling is to be used
+ * @abx500_adc_therm	placement of thermistor, batctrl or battemp adc
+ * @chg_unknown_bat	flag to enable charging of unknown batteries
+ * @enable_overshoot	flag to enable VBAT overshoot control
+ * @auto_trig		flag to enable auto adc trigger
+ * @fg_res		resistance of FG resistor in 0.1mOhm
+ * @n_btypes		number of elements in array bat_type
+ * @batt_id		index of the identified battery in array bat_type
+ * @interval_charging	charge alg cycle period time when charging (sec)
+ * @interval_not_charging charge alg cycle period time when not charging (sec)
+ * @temp_hysteresis	temperature hysteresis
+ * @gnd_lift_resistance	Battery ground to phone ground resistance (mOhm)
+ * @n_chg_out_curr		number of elements in array chg_output_curr
+ * @n_chg_in_curr		number of elements in array chg_input_curr
+ * @chg_output_curr	charger output current level map
+ * @chg_input_curr		charger input current level map
+ * @maxi		maximization parameters
+ * @cap_levels		capacity in percent for the different capacity levels
+ * @bat_type		table of supported battery types
+ * @chg_params		charger parameters
+ * @fg_params		fuel gauge parameters
+ */
+struct abx500_bm_data {
+	int temp_under;
+	int temp_low;
+	int temp_high;
+	int temp_over;
+	int temp_now;
+	int temp_interval_chg;
+	int temp_interval_nochg;
+	int main_safety_tmr_h;
+	int usb_safety_tmr_h;
+	int bkup_bat_v;
+	int bkup_bat_i;
+	bool autopower_cfg;
+	bool ac_enabled;
+	bool usb_enabled;
+	bool no_maintenance;
+	bool capacity_scaling;
+	bool chg_unknown_bat;
+	bool enable_overshoot;
+	bool auto_trig;
+	enum abx500_adc_therm adc_therm;
+	int fg_res;
+	int n_btypes;
+	int batt_id;
+	int interval_charging;
+	int interval_not_charging;
+	int temp_hysteresis;
+	int gnd_lift_resistance;
+	int n_chg_out_curr;
+	int n_chg_in_curr;
+	int *chg_output_curr;
+	int *chg_input_curr;
+	const struct abx500_maxim_parameters *maxi;
+	const struct abx500_bm_capacity_levels *cap_levels;
+	struct abx500_battery_type *bat_type;
+	const struct abx500_bm_charger_parameters *chg_params;
+	const struct abx500_fg_parameters *fg_params;
+};
+
+enum {
+	NTC_EXTERNAL = 0,
+	NTC_INTERNAL,
+};
+
 /**
  * struct res_to_temp - defines one point in a temp to res curve. To
  * be used in battery packs that combines the identification resistor with a
@@ -447,9 +717,6 @@ struct ab8500_bm_data {
 	const struct ab8500_fg_parameters *fg_params;
 };
 
-struct ab8500_btemp;
-struct ab8500_fg;
-
 extern struct abx500_bm_data ab8500_bm_data;
 
 void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA);
@@ -459,5 +726,8 @@ int ab8500_fg_inst_curr_start(struct ab8500_fg *di);
 int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res);
 int ab8500_fg_inst_curr_started(struct ab8500_fg *di);
 int ab8500_fg_inst_curr_done(struct ab8500_fg *di);
+int ab8500_bm_of_probe(struct device *dev,
+		       struct device_node *np,
+		       struct abx500_bm_data *bm);
 
 #endif /* _AB8500_CHARGER_H_ */