diff options
| author | Hans de Goede <hdegoede@redhat.com> | 2021-08-01 15:31:05 +0200 |
|---|---|---|
| committer | Sebastian Reichel <sebastian.reichel@collabora.com> | 2021-08-05 18:54:52 +0200 |
| commit | 213e19d659f9bb891387f105281a63700594a3dd (patch) | |
| tree | 6d4f7335584aeb24c38d97bc6d398768faa196a4 /drivers/power | |
| parent | 964b3e9b02bd89a17fdd108a2ecb053beba2b43f (diff) | |
power: supply: axp288_fuel_gauge: Take the P-Unit semaphore only once during probe()
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer and this is a quite expensive operation.
Explicitly take the semaphore in probe() around the register-accesses
done during probe, so that this only needs to be done once, rather then
once per register-access.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Diffstat (limited to 'drivers/power')
| -rw-r--r-- | drivers/power/supply/axp288_fuel_gauge.c | 24 |
1 files changed, 17 insertions, 7 deletions
diff --git a/drivers/power/supply/axp288_fuel_gauge.c b/drivers/power/supply/axp288_fuel_gauge.c index 016d8d6bec40..c1da217fdb0e 100644 --- a/drivers/power/supply/axp288_fuel_gauge.c +++ b/drivers/power/supply/axp288_fuel_gauge.c @@ -661,31 +661,35 @@ static int axp288_fuel_gauge_probe(struct platform_device *pdev) } } + ret = iosf_mbi_block_punit_i2c_access(); + if (ret < 0) + goto out_free_iio_chan; + /* * On some devices the fuelgauge and charger parts of the axp288 are * not used, check that the fuelgauge is enabled (CC_CTRL != 0). */ ret = regmap_read(axp20x->regmap, AXP20X_CC_CTRL, &val); if (ret < 0) - goto out_free_iio_chan; + goto unblock_punit_i2c_access; if (val == 0) { ret = -ENODEV; - goto out_free_iio_chan; + goto unblock_punit_i2c_access; } ret = fuel_gauge_reg_readb(info, AXP288_FG_DES_CAP1_REG); if (ret < 0) - goto out_free_iio_chan; + goto unblock_punit_i2c_access; if (!(ret & FG_DES_CAP1_VALID)) { dev_err(&pdev->dev, "axp288 not configured by firmware\n"); ret = -ENODEV; - goto out_free_iio_chan; + goto unblock_punit_i2c_access; } ret = fuel_gauge_reg_readb(info, AXP20X_CHRG_CTRL1); if (ret < 0) - goto out_free_iio_chan; + goto unblock_punit_i2c_access; switch ((ret & CHRG_CCCV_CV_MASK) >> CHRG_CCCV_CV_BIT_POS) { case CHRG_CCCV_CV_4100MV: info->max_volt = 4100; @@ -703,14 +707,20 @@ static int axp288_fuel_gauge_probe(struct platform_device *pdev) ret = fuel_gauge_reg_readb(info, AXP20X_PWR_OP_MODE); if (ret < 0) - goto out_free_iio_chan; + goto unblock_punit_i2c_access; info->pwr_op = ret; ret = fuel_gauge_reg_readb(info, AXP288_FG_LOW_CAP_REG); if (ret < 0) - goto out_free_iio_chan; + goto unblock_punit_i2c_access; info->low_cap = ret; +unblock_punit_i2c_access: + iosf_mbi_unblock_punit_i2c_access(); + /* In case we arrive here by goto because of a register access error */ + if (ret < 0) + goto out_free_iio_chan; + psy_cfg.drv_data = info; info->bat = power_supply_register(&pdev->dev, &fuel_gauge_desc, &psy_cfg); if (IS_ERR(info->bat)) { |