Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Olof Johansson:
 "SoC changes, a substantial part of this is cleanup of some of the
  older platforms that used to have a bunch of board files.

  In particular:

   - Remove non-DT i.MX platforms that haven't seen activity in years,
     it's time to remove them.

   - A bunch of cleanup and removal of platform data for TI/OMAP
     platforms, moving over to genpd for power/reset control (yay!)

   - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
     closer to multiplatform support (not quite there yet, but getting
     close).

  There are a few other changes too, smaller fixlets, etc. For new
  platform support, the primary ones are:

   - New SoC: Hisilicon SD5203, ARM926EJ-S platform.

   - Cpufreq support for i.MX7ULP"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
  ARM: mstar: Select MStar intc
  ARM: stm32: Replace HTTP links with HTTPS ones
  ARM: debug: add UART early console support for SD5203
  ARM: hisi: add support for SD5203 SoC
  ARM: omap3: enable off mode automatically
  clk: imx: imx35: Remove mx35_clocks_init()
  clk: imx: imx31: Remove mx31_clocks_init()
  clk: imx: imx27: Remove mx27_clocks_init()
  ARM: imx: Remove unused definitions
  ARM: imx35: Retrieve the IIM base address from devicetree
  ARM: imx3: Retrieve the AVIC base address from devicetree
  ARM: imx3: Retrieve the CCM base address from devicetree
  ARM: imx31: Retrieve the IIM base address from devicetree
  ARM: imx27: Retrieve the CCM base address from devicetree
  ARM: imx27: Retrieve the SYSCTRL base address from devicetree
  ARM: s3c64xx: bring back notes from removed debug-macro.S
  ARM: s3c24xx: fix Wunused-variable warning on !MMU
  ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
  MAINTAINERS: mark linux-samsung-soc list non-moderated
  ARM: imx: Remove remnant board file support pieces
  ...

402 files changed, 3377 insertions, 19357 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c18fa9d382b7..fe2f17eb2b50 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -268,9 +268,7 @@ config PHYS_OFFSET
 	depends on !ARM_PATCH_PHYS_VIRT
 	default DRAM_BASE if !MMU
 	default 0x00000000 if ARCH_EBSA110 || \
-			ARCH_FOOTBRIDGE || \
-			ARCH_INTEGRATOR || \
-			ARCH_REALVIEW
+			ARCH_FOOTBRIDGE
 	default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
 	default 0x20000000 if ARCH_S5PV210
 	default 0xc0000000 if ARCH_SA1100
@@ -506,11 +504,12 @@ config ARCH_S3C24XX
 	select GPIOLIB
 	select GENERIC_IRQ_MULTI_HANDLER
 	select HAVE_S3C2410_I2C if I2C
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select HAVE_S3C_RTC if RTC_CLASS
 	select NEED_MACH_IO_H
+	select S3C2410_WATCHDOG
 	select SAMSUNG_ATAGS
 	select USE_OF
+	select WATCHDOG
 	help
 	  Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
 	  and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
@@ -639,7 +638,6 @@ source "arch/arm/mach-dove/Kconfig"
 source "arch/arm/mach-ep93xx/Kconfig"
 
 source "arch/arm/mach-exynos/Kconfig"
-source "arch/arm/plat-samsung/Kconfig"
 
 source "arch/arm/mach-footbridge/Kconfig"
 
@@ -712,9 +710,7 @@ source "arch/arm/mach-realview/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
 
-source "arch/arm/mach-s3c24xx/Kconfig"
-
-source "arch/arm/mach-s3c64xx/Kconfig"
+source "arch/arm/mach-s3c/Kconfig"
 
 source "arch/arm/mach-s5pv210/Kconfig"
 
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 87912e5c2256..8986a91a6f31 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -1005,7 +1005,7 @@ choice
 		  via SCIFA4 on Renesas SH-Mobile AG5 (SH73A0).
 
 	config DEBUG_S3C_UART0
-		depends on PLAT_SAMSUNG
+		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1017,7 +1017,7 @@ choice
 		  by the boot-loader before use.
 
 	config DEBUG_S3C_UART1
-		depends on PLAT_SAMSUNG
+		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1029,7 +1029,7 @@ choice
 		  by the boot-loader before use.
 
 	config DEBUG_S3C_UART2
-		depends on PLAT_SAMSUNG
+		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
@@ -1041,7 +1041,7 @@ choice
 		  by the boot-loader before use.
 
 	config DEBUG_S3C_UART3
-		depends on PLAT_SAMSUNG && (ARCH_EXYNOS || ARCH_S5PV210)
+		depends on ARCH_EXYNOS || ARCH_S5PV210
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
 		select DEBUG_S5PV210_UART if ARCH_S5PV210
@@ -1086,6 +1086,14 @@ choice
 		  on SA-11x0 UART ports. The kernel will check for the first
 		  enabled UART in a sequence 3-1-2.
 
+	config DEBUG_SD5203_UART
+		bool "Hisilicon SD5203 Debug UART"
+		depends on ARCH_SD5203
+		select DEBUG_UART_8250
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on SD5203 UART.
+
 	config DEBUG_SOCFPGA_UART0
 		depends on ARCH_SOCFPGA
 		bool "Use SOCFPGA UART0 for low-level debug"
@@ -1497,6 +1505,16 @@ config DEBUG_S3C64XX_UART
 config DEBUG_S5PV210_UART
 	bool
 
+config DEBUG_S3C_UART
+	depends on DEBUG_S3C2410_UART || DEBUG_S3C24XX_UART || \
+		   DEBUG_S3C64XX_UART ||  DEBUG_S5PV210_UART || \
+		   DEBUG_EXYNOS_UART
+	int
+	default "0" if DEBUG_S3C_UART0
+	default "1" if DEBUG_S3C_UART1
+	default "2" if DEBUG_S3C_UART2
+	default "3" if DEBUG_S3C_UART3
+
 config DEBUG_OMAP2PLUS_UART
 	bool
 	depends on ARCH_OMAP2PLUS
@@ -1650,6 +1668,7 @@ config DEBUG_UART_PHYS
 	default 0x11006000 if DEBUG_MT6589_UART0
 	default 0x11009000 if DEBUG_MT8135_UART3
 	default 0x16000000 if DEBUG_INTEGRATOR
+	default 0x1600d000 if DEBUG_SD5203_UART
 	default 0x18000300 if DEBUG_BCM_5301X
 	default 0x18000400 if DEBUG_BCM_HR2
 	default 0x18010000 if DEBUG_SIRFATLAS7_UART0
@@ -1852,7 +1871,7 @@ config DEBUG_UART_VIRT
 	default 0xfec60000 if DEBUG_SIRFPRIMA2_UART1
 	default 0xfec90000 if DEBUG_RK32_UART2
 	default 0xfed0c000 if DEBUG_DAVINCI_DA8XX_UART1
-	default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2
+	default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_SD5203_UART
 	default 0xfed60000 if DEBUG_RK29_UART0
 	default 0xfed64000 if DEBUG_RK29_UART1 || DEBUG_RK3X_UART2
 	default 0xfed68000 if DEBUG_RK29_UART2 || DEBUG_RK3X_UART3
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 2874cd9923b7..4d76eab2b22d 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -212,8 +212,7 @@ machine-$(CONFIG_ARCH_REALTEK)		+= realtek
 machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
-machine-$(CONFIG_ARCH_S3C24XX)		+= s3c24xx
-machine-$(CONFIG_ARCH_S3C64XX)		+= s3c64xx
+machine-$(CONFIG_PLAT_SAMSUNG)		+= s3c
 machine-$(CONFIG_ARCH_S5PV210)		+= s5pv210
 machine-$(CONFIG_ARCH_SA1100)		+= sa1100
 machine-$(CONFIG_ARCH_RENESAS)	 	+= shmobile
@@ -235,13 +234,9 @@ machine-$(CONFIG_PLAT_SPEAR)		+= spear
 
 # Platform directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_EXYNOS)	+= samsung
 plat-$(CONFIG_ARCH_OMAP)	+= omap
-plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
-plat-$(CONFIG_ARCH_S5PV210)	+= samsung
 plat-$(CONFIG_PLAT_ORION)	+= orion
 plat-$(CONFIG_PLAT_PXA)		+= pxa
-plat-$(CONFIG_PLAT_S3C24XX)	+= samsung
 plat-$(CONFIG_PLAT_VERSATILE)	+= versatile
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi
index b88d0caa4b2d..ea20e4bdf040 100644
--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@@ -425,7 +425,6 @@
 
 		target-module@3e000 {			/* 0x44e3e000, ap 35 60.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtc";
 			reg = <0x3e074 0x4>,
 			      <0x3e078 0x4>;
 			reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 5cb4cc37cb6d..0fab080d61ef 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -578,6 +578,7 @@
 					<SYSC_IDLE_SMART>;
 			clocks = <&gfx_l3_clkctrl AM3_GFX_L3_GFX_CLKCTRL 0>;
 			clock-names = "fck";
+			power-domains = <&prm_gfx>;
 			resets = <&prm_gfx 0>;
 			reset-names = "rstctrl";
 			#address-cells = <1>;
@@ -617,6 +618,7 @@
 	prm_gfx: prm@1100 {
 		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
 		reg = <0x1100 0x100>;
+		#power-domain-cells = <0>;
 		#reset-cells = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 14314046256c..8d47913e2129 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -517,6 +517,7 @@
 					<SYSC_IDLE_SMART>;
 			clocks = <&gfx_l3_clkctrl AM4_GFX_L3_GFX_CLKCTRL 0>;
 			clock-names = "fck";
+			power-domains = <&prm_gfx>;
 			resets = <&prm_gfx 0>;
 			reset-names = "rstctrl";
 			#address-cells = <1>;
@@ -533,6 +534,7 @@
 	prm_gfx: prm@400 {
 		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
 		reg = <0x400 0x100>;
+		#power-domain-cells = <0>;
 		#reset-cells = <1>;
 	};
 
diff --git a/arch/arm/boot/dts/am437x-l4.dtsi b/arch/arm/boot/dts/am437x-l4.dtsi
index 3d393fe252c6..8a67bb29e3b7 100644
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/am437x-l4.dtsi
@@ -409,9 +409,8 @@
 			ranges = <0x0 0x39000 0x1000>;
 		};
 
-		target-module@3e000 {			/* 0x44e3e000, ap 34 60.0 */
+		rtc_target: target-module@3e000 {	/* 0x44e3e000, ap 34 60.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtc";
 			reg = <0x3e074 0x4>,
 			      <0x3e078 0x4>;
 			reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index de4fc78498a0..7f3faa36a5e4 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -833,6 +833,10 @@
 	status = "okay";
 };
 
+&rtc_target {
+	status = "disabled";
+};
+
 &tscadc {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi
index 27a6a83cc60c..f43b764cc0c7 100644
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/dra7-l4.dtsi
@@ -3561,7 +3561,6 @@
 
 		rtctarget: target-module@38000 {			/* 0x48838000, ap 29 12.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtcss";
 			reg = <0x38074 0x4>,
 			      <0x38078 0x4>;
 			reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/omap4-l4-abe.dtsi b/arch/arm/boot/dts/omap4-l4-abe.dtsi
index b2cf5f41e222..a9573d441dea 100644
--- a/arch/arm/boot/dts/omap4-l4-abe.dtsi
+++ b/arch/arm/boot/dts/omap4-l4-abe.dtsi
@@ -1,14 +1,16 @@
 &l4_abe {						/* 0x40100000 */
-	compatible = "ti,omap4-l4-abe", "simple-bus";
+	compatible = "ti,omap4-l4-abe", "simple-pm-bus";
 	reg = <0x40100000 0x400>,
 	      <0x40100400 0x400>;
 	reg-names = "la", "ap";
+	power-domains = <&prm_abe>;
+	/* OMAP4_L4_ABE_CLKCTRL is read-only */
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0x00000000 0x40100000 0x100000>,	/* segment 0 */
 		 <0x49000000 0x49000000 0x100000>;
 	segment@0 {					/* 0x40100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges =
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 0282b9de3384..eb5780eb2630 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -658,6 +658,12 @@
 		#reset-cells = <1>;
 	};
 
+	prm_abe: prm@500 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
 	prm_core: prm@700 {
 		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
 		reg = <0x700 0x100>;
diff --git a/arch/arm/boot/dts/omap5-l4-abe.dtsi b/arch/arm/boot/dts/omap5-l4-abe.dtsi
index 25b7fce8de2d..a03bca5a3584 100644
--- a/arch/arm/boot/dts/omap5-l4-abe.dtsi
+++ b/arch/arm/boot/dts/omap5-l4-abe.dtsi
@@ -1,14 +1,16 @@
 &l4_abe {						/* 0x40100000 */
-	compatible = "ti,omap5-l4-abe", "simple-bus";
+	compatible = "ti,omap5-l4-abe", "simple-pm-bus";
 	reg = <0x40100000 0x400>,
 	      <0x40100400 0x400>;
 	reg-names = "la", "ap";
+	power-domains = <&prm_abe>;
+	/* OMAP5_L4_ABE_CLKCTRL is read-only */
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0x00000000 0x40100000 0x100000>,	/* segment 0 */
 		 <0x49000000 0x49000000 0x100000>;
 	segment@0 {					/* 0x40100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges =
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index a82c96258a93..2bf2e5839a7f 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -676,6 +676,12 @@
 		#reset-cells = <1>;
 	};
 
+	prm_abe: prm@500 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
 	prm_core: prm@700 {
 		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
 		reg = <0x700 0x100>;
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index f5f1111f2118..aeb1209e0804 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -20,9 +20,9 @@ CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
 CONFIG_MACH_PCA100=y
-CONFIG_MACH_IMX27_DT=y
 CONFIG_SOC_IMX1=y
 CONFIG_SOC_IMX25=y
+CONFIG_SOC_IMX27=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 82d3ffb18e70..e1d83018d022 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -15,20 +15,8 @@ CONFIG_PERF_EVENTS=y
 # CONFIG_COMPAT_BRK is not set
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_MXC=y
-CONFIG_MACH_MX31LILLY=y
-CONFIG_MACH_MX31LITE=y
-CONFIG_MACH_PCM037=y
-CONFIG_MACH_PCM037_EET=y
-CONFIG_MACH_MX31_3DS=y
-CONFIG_MACH_MX31MOBOARD=y
-CONFIG_MACH_QONG=y
-CONFIG_MACH_ARMADILLO5X0=y
-CONFIG_MACH_KZM_ARM11_01=y
-CONFIG_MACH_IMX31_DT=y
-CONFIG_MACH_IMX35_DT=y
-CONFIG_MACH_PCM043=y
-CONFIG_MACH_MX35_3DS=y
-CONFIG_MACH_VPR200=y
+CONFIG_SOC_IMX31=y
+CONFIG_SOC_IMX35=y
 CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
 CONFIG_SOC_IMX53=y
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index 2724fb3155cd..70b709a669d2 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -29,8 +29,8 @@ CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
 CONFIG_MACH_PCA100=y
-CONFIG_MACH_IMX27_DT=y
 CONFIG_SOC_IMX25=y
+CONFIG_SOC_IMX27=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_KIRKWOOD=y
 CONFIG_ARCH_ORION5X=y
diff --git a/arch/arm/include/debug/brcmstb.S b/arch/arm/include/debug/brcmstb.S
index 7ffe66993029..0ff32ffc610c 100644
--- a/arch/arm/include/debug/brcmstb.S
+++ b/arch/arm/include/debug/brcmstb.S
@@ -32,6 +32,8 @@
 #define UARTA_7271		UARTA_7268
 #define UARTA_7278		REG_PHYS_ADDR_V7(0x40c000)
 #define UARTA_7216		UARTA_7278
+#define UARTA_72164		UARTA_7278
+#define UARTA_72165		UARTA_7278
 #define UARTA_7364		REG_PHYS_ADDR(0x40b000)
 #define UARTA_7366		UARTA_7364
 #define UARTA_74371		REG_PHYS_ADDR(0x406b00)
@@ -84,17 +86,19 @@ ARM_BE8(	rev	\rv, \rv )
 		/* Chip specific detection starts here */
 20:		checkuart(\rp, \rv, 0x33900000, 3390)
 21:		checkuart(\rp, \rv, 0x72160000, 7216)
-22:		checkuart(\rp, \rv, 0x72500000, 7250)
-23:		checkuart(\rp, \rv, 0x72550000, 7255)
-24:		checkuart(\rp, \rv, 0x72600000, 7260)
-25:		checkuart(\rp, \rv, 0x72680000, 7268)
-26:		checkuart(\rp, \rv, 0x72710000, 7271)
-27:		checkuart(\rp, \rv, 0x72780000, 7278)
-28:		checkuart(\rp, \rv, 0x73640000, 7364)
-29:		checkuart(\rp, \rv, 0x73660000, 7366)
-30:		checkuart(\rp, \rv, 0x07437100, 74371)
-31:		checkuart(\rp, \rv, 0x74390000, 7439)
-32:		checkuart(\rp, \rv, 0x74450000, 7445)
+22:		checkuart(\rp, \rv, 0x07216400, 72164)
+23:		checkuart(\rp, \rv, 0x07216500, 72165)
+24:		checkuart(\rp, \rv, 0x72500000, 7250)
+25:		checkuart(\rp, \rv, 0x72550000, 7255)
+26:		checkuart(\rp, \rv, 0x72600000, 7260)
+27:		checkuart(\rp, \rv, 0x72680000, 7268)
+28:		checkuart(\rp, \rv, 0x72710000, 7271)
+29:		checkuart(\rp, \rv, 0x72780000, 7278)
+30:		checkuart(\rp, \rv, 0x73640000, 7364)
+31:		checkuart(\rp, \rv, 0x73660000, 7366)
+32:		checkuart(\rp, \rv, 0x07437100, 74371)
+33:		checkuart(\rp, \rv, 0x74390000, 7439)
+34:		checkuart(\rp, \rv, 0x74450000, 7445)
 
 		/* No valid UART found */
 90:		mov	\rp, #0
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 2aab043441e8..120f9aa6fff3 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -51,10 +51,11 @@ static struct at91_soc_pm soc_pm = {
 };
 
 static const match_table_t pm_modes __initconst = {
-	{ AT91_PM_STANDBY, "standby" },
-	{ AT91_PM_ULP0, "ulp0" },
-	{ AT91_PM_ULP1, "ulp1" },
-	{ AT91_PM_BACKUP, "backup" },
+	{ AT91_PM_STANDBY,	"standby" },
+	{ AT91_PM_ULP0,		"ulp0" },
+	{ AT91_PM_ULP0_FAST,    "ulp0-fast" },
+	{ AT91_PM_ULP1,		"ulp1" },
+	{ AT91_PM_BACKUP,	"backup" },
 	{ -1, NULL },
 };
 
@@ -557,11 +558,6 @@ static void at91rm9200_idle(void)
 	writel(AT91_PMC_PCK, soc_pm.data.pmc + AT91_PMC_SCDR);
 }
 
-static void at91sam9x60_idle(void)
-{
-	cpu_do_idle();
-}
-
 static void at91sam9_idle(void)
 {
 	writel(AT91_PMC_PCK, soc_pm.data.pmc + AT91_PMC_SCDR);
@@ -789,6 +785,51 @@ static const struct of_device_id atmel_pmc_ids[] __initconst = {
 	{ /* sentinel */ },
 };
 
+static void __init at91_pm_modes_validate(const int *modes, int len)
+{
+	u8 i, standby = 0, suspend = 0;
+	int mode;
+
+	for (i = 0; i < len; i++) {
+		if (standby && suspend)
+			break;
+
+		if (modes[i] == soc_pm.data.standby_mode && !standby) {
+			standby = 1;
+			continue;
+		}
+
+		if (modes[i] == soc_pm.data.suspend_mode && !suspend) {
+			suspend = 1;
+			continue;
+		}
+	}
+
+	if (!standby) {
+		if (soc_pm.data.suspend_mode == AT91_PM_STANDBY)
+			mode = AT91_PM_ULP0;
+		else
+			mode = AT91_PM_STANDBY;
+
+		pr_warn("AT91: PM: %s mode not supported! Using %s.\n",
+			pm_modes[soc_pm.data.standby_mode].pattern,
+			pm_modes[mode].pattern);
+		soc_pm.data.standby_mode = mode;
+	}
+
+	if (!suspend) {
+		if (soc_pm.data.standby_mode == AT91_PM_ULP0)
+			mode = AT91_PM_STANDBY;
+		else
+			mode = AT91_PM_ULP0;
+
+		pr_warn("AT91: PM: %s mode not supported! Using %s.\n",
+			pm_modes[soc_pm.data.suspend_mode].pattern,
+			pm_modes[mode].pattern);
+		soc_pm.data.suspend_mode = mode;
+	}
+}
+
 static void __init at91_pm_init(void (*pm_idle)(void))
 {
 	struct device_node *pmc_np;
@@ -800,6 +841,7 @@ static void __init at91_pm_init(void (*pm_idle)(void))
 
 	pmc_np = of_find_matching_node_and_match(NULL, atmel_pmc_ids, &of_id);
 	soc_pm.data.pmc = of_iomap(pmc_np, 0);
+	of_node_put(pmc_np);
 	if (!soc_pm.data.pmc) {
 		pr_err("AT91: PM not supported, PMC not found\n");
 		return;
@@ -830,6 +872,14 @@ void __init at91rm9200_pm_init(void)
 	if (!IS_ENABLED(CONFIG_SOC_AT91RM9200))
 		return;
 
+	/*
+	 * Force STANDBY and ULP0 mode to avoid calling
+	 * at91_pm_modes_validate() which may increase booting time.
+	 * Platform supports anyway only STANDBY and ULP0 modes.
+	 */
+	soc_pm.data.standby_mode = AT91_PM_STANDBY;
+	soc_pm.data.suspend_mode = AT91_PM_ULP0;
+
 	at91_dt_ramc();
 
 	/*
@@ -842,12 +892,17 @@ void __init at91rm9200_pm_init(void)
 
 void __init sam9x60_pm_init(void)
 {
+	static const int modes[] __initconst = {
+		AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST, AT91_PM_ULP1,
+	};
+
 	if (!IS_ENABLED(CONFIG_SOC_SAM9X60))
 		return;
 
+	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_pm_modes_init();
 	at91_dt_ramc();
-	at91_pm_init(at91sam9x60_idle);
+	at91_pm_init(NULL);
 
 	soc_pm.ws_ids = sam9x60_ws_ids;
 	soc_pm.config_pmc_ws = at91_sam9x60_config_pmc_ws;
@@ -858,26 +913,46 @@ void __init at91sam9_pm_init(void)
 	if (!IS_ENABLED(CONFIG_SOC_AT91SAM9))
 		return;
 
+	/*
+	 * Force STANDBY and ULP0 mode to avoid calling
+	 * at91_pm_modes_validate() which may increase booting time.
+	 * Platform supports anyway only STANDBY and ULP0 modes.
+	 */
+	soc_pm.data.standby_mode = AT91_PM_STANDBY;
+	soc_pm.data.suspend_mode = AT91_PM_ULP0;
+
 	at91_dt_ramc();
 	at91_pm_init(at91sam9_idle);
 }
 
 void __init sama5_pm_init(void)
 {
+	static const int modes[] __initconst = {
+		AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST,
+	};
+
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5))
 		return;
 
+	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_dt_ramc();
 	at91_pm_init(NULL);
 }
 
 void __init sama5d2_pm_init(void)
 {
+	static const int modes[] __initconst = {
+		AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST, AT91_PM_ULP1,
+		AT91_PM_BACKUP,
+	};
+
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5D2))
 		return;
 
+	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_pm_modes_init();
-	sama5_pm_init();
+	at91_dt_ramc();
+	at91_pm_init(NULL);
 
 	soc_pm.ws_ids = sama5d2_ws_ids;
 	soc_pm.config_shdwc_ws = at91_sama5d2_config_shdwc_ws;
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index 218e8d1a30fb..bfb260be371e 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -19,8 +19,9 @@
 
 #define	AT91_PM_STANDBY		0x00
 #define AT91_PM_ULP0		0x01
-#define AT91_PM_ULP1		0x02
-#define	AT91_PM_BACKUP		0x03
+#define AT91_PM_ULP0_FAST	0x02
+#define AT91_PM_ULP1		0x03
+#define	AT91_PM_BACKUP		0x04
 
 #ifndef __ASSEMBLY__
 struct at91_pm_data {
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index be9764e8d3fa..0184de05c1be 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -164,7 +164,22 @@ ENDPROC(at91_backup_mode)
 
 .macro at91_pm_ulp0_mode
 	ldr	pmc, .pmc_base
+	ldr	tmp2, .pm_mode
+	ldr	tmp3, .mckr_offset
+
+	/* Check if ULP0 fast variant has been requested. */
+	cmp	tmp2, #AT91_PM_ULP0_FAST
+	bne	0f
+
+	/* Set highest prescaler for power saving */
+	ldr	tmp1, [pmc, tmp3]
+	bic	tmp1, tmp1, #AT91_PMC_PRES
+	orr	tmp1, tmp1, #AT91_PMC_PRES_64
+	str	tmp1, [pmc, tmp3]
+	wait_mckrdy
+	b	1f
 
+0:
 	/* Turn off the crystal oscillator */
 	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
 	bic	tmp1, tmp1, #AT91_PMC_MOSCEN
@@ -192,7 +207,18 @@ ENDPROC(at91_backup_mode)
 	/* Wait for interrupt */
 1:	at91_cpu_idle
 
-	/* Restore RC oscillator state */
+	/* Check if ULP0 fast variant has been requested. */
+	cmp	tmp2, #AT91_PM_ULP0_FAST
+	bne	5f
+
+	/* Set lowest prescaler for fast resume. */
+	ldr	tmp1, [pmc, tmp3]
+	bic	tmp1, tmp1, #AT91_PMC_PRES
+	str	tmp1, [pmc, tmp3]
+	wait_mckrdy
+	b	6f
+
+5:	/* Restore RC oscillator state */
 	ldr	tmp1, .saved_osc_status
 	tst	tmp1, #AT91_PMC_MOSCRCS
 	beq	4f
@@ -216,6 +242,7 @@ ENDPROC(at91_backup_mode)
 	str	tmp1, [pmc, #AT91_CKGR_MOR]
 
 	wait_moscrdy
+6:
 .endm
 
 /**
@@ -473,23 +500,29 @@ ENDPROC(at91_backup_mode)
 ENTRY(at91_ulp_mode)
 	ldr	pmc, .pmc_base
 	ldr	tmp2, .mckr_offset
+	ldr	tmp3, .pm_mode
 
 	/* Save Master clock setting */
 	ldr	tmp1, [pmc, tmp2]
 	str	tmp1, .saved_mckr
 
 	/*
-	 * Set the Master clock source to slow clock
+	 * Set master clock source to:
+	 * - MAINCK if using ULP0 fast variant
+	 * - slow clock, otherwise
 	 */
 	bic	tmp1, tmp1, #AT91_PMC_CSS
+	cmp	tmp3, #AT91_PM_ULP0_FAST
+	bne	save_mck
+	orr	tmp1, tmp1, #AT91_PMC_CSS_MAIN
+save_mck:
 	str	tmp1, [pmc, tmp2]
 
 	wait_mckrdy
 
 	at91_plla_disable
 
-	ldr	r0, .pm_mode
-	cmp	r0, #AT91_PM_ULP1
+	cmp	tmp3, #AT91_PM_ULP1
 	beq	ulp1_mode
 
 	at91_pm_ulp0_mode
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index 1df0ee01ee02..ae790908fc74 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -208,6 +208,7 @@ config ARCH_BRCMSTB
 	select ARM_GIC
 	select ARM_ERRATA_798181 if SMP
 	select HAVE_ARM_ARCH_TIMER
+	select BCM7038_L1_IRQ
 	select BRCMSTB_L2_IRQ
 	select BCM7120_L2_IRQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
index bcb3c4070945..7755cccec550 100644
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ b/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -548,8 +548,7 @@ static const struct property_entry eeprom_properties[] = {
  */
 static struct i2c_client *dm6446evm_msp;
 
-static int dm6446evm_msp_probe(struct i2c_client *client,
-		const struct i2c_device_id *id)
+static int dm6446evm_msp_probe(struct i2c_client *client)
 {
 	dm6446evm_msp = client;
 	return 0;
@@ -569,7 +568,7 @@ static const struct i2c_device_id dm6446evm_msp_ids[] = {
 static struct i2c_driver dm6446evm_msp_driver = {
 	.driver.name	= "dm6446evm_msp",
 	.id_table	= dm6446evm_msp_ids,
-	.probe		= dm6446evm_msp_probe,
+	.probe_new	= dm6446evm_msp_probe,
 	.remove		= dm6446evm_msp_remove,
 };
 
diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
index 8319a6067a68..952ddabc743e 100644
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ b/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -160,8 +160,7 @@ static struct platform_device davinci_aemif_device = {
 #define DM646X_EVM_ATA_PWD		BIT(1)
 
 /* CPLD Register 0 Client: used for I/O Control */
-static int cpld_reg0_probe(struct i2c_client *client,
-			   const struct i2c_device_id *id)
+static int cpld_reg0_probe(struct i2c_client *client)
 {
 	if (HAS_ATA) {
 		u8 data;
@@ -197,7 +196,7 @@ static const struct i2c_device_id cpld_reg_ids[] = {
 static struct i2c_driver dm6467evm_cpld_driver = {
 	.driver.name	= "cpld_reg0",
 	.id_table	= cpld_reg_ids,
-	.probe		= cpld_reg0_probe,
+	.probe_new	= cpld_reg0_probe,
 };
 
 /* LEDS */
@@ -397,8 +396,7 @@ static struct snd_platform_data dm646x_evm_snd_data[] = {
 #ifdef CONFIG_I2C
 static struct i2c_client *cpld_client;
 
-static int cpld_video_probe(struct i2c_client *client,
-			const struct i2c_device_id *id)
+static int cpld_video_probe(struct i2c_client *client)
 {
 	cpld_client = client;
 	return 0;
@@ -419,7 +417,7 @@ static struct i2c_driver cpld_video_driver = {
 	.driver = {
 		.name	= "cpld_video",
 	},
-	.probe		= cpld_video_probe,
+	.probe_new	= cpld_video_probe,
 	.remove		= cpld_video_remove,
 	.id_table	= cpld_video_id,
 };
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index f185cd3d4c62..d2d249706ebb 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -24,7 +24,6 @@ menuconfig ARCH_EXYNOS
 	select HAVE_ARM_ARCH_TIMER if ARCH_EXYNOS5
 	select HAVE_ARM_SCU if SMP
 	select HAVE_S3C2410_I2C if I2C
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select HAVE_S3C_RTC if RTC_CLASS
 	select PINCTRL
 	select PINCTRL_EXYNOS
diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile
index 0fd3fcf8bfb0..53fa363c8e44 100644
--- a/arch/arm/mach-exynos/Makefile
+++ b/arch/arm/mach-exynos/Makefile
@@ -3,10 +3,6 @@
 # Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
 #		http://www.samsung.com/
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
-
-# Core
-
 obj-$(CONFIG_ARCH_EXYNOS)	+= exynos.o exynos-smc.o firmware.o
 
 obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm.o sleep.o
diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
index afd988a92836..29eb075b24a4 100644
--- a/arch/arm/mach-exynos/common.h
+++ b/arch/arm/mach-exynos/common.h
@@ -24,12 +24,12 @@
 #define EXYNOS5800_SOC_ID	0xE5422000
 #define EXYNOS5_SOC_MASK	0xFFFFF000
 
-extern unsigned long samsung_cpu_id;
+extern unsigned long exynos_cpu_id;
 
 #define IS_SAMSUNG_CPU(name, id, mask)		\
 static inline int is_samsung_##name(void)	\
 {						\
-	return ((samsung_cpu_id & mask) == (id & mask));	\
+	return ((exynos_cpu_id & mask) == (id & mask));	\
 }
 
 IS_SAMSUNG_CPU(exynos3250, EXYNOS3250_SOC_ID, EXYNOS3_SOC_MASK)
@@ -147,7 +147,7 @@ extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data;
 
 extern void exynos_set_delayed_reset_assertion(bool enable);
 
-extern unsigned int samsung_rev(void);
+extern unsigned int exynos_rev(void);
 extern void exynos_core_restart(u32 core_id);
 extern int exynos_set_boot_addr(u32 core_id, unsigned long boot_addr);
 extern int exynos_get_boot_addr(u32 core_id, unsigned long *boot_addr);
diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
index 36c37444485a..700763e07083 100644
--- a/arch/arm/mach-exynos/exynos.c
+++ b/arch/arm/mach-exynos/exynos.c
@@ -19,11 +19,12 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/map.h>
-#include <plat/cpu.h>
-
 #include "common.h"
 
+#define S3C_ADDR_BASE	0xF6000000
+#define S3C_ADDR(x)	((void __iomem __force *)S3C_ADDR_BASE + (x))
+#define S5P_VA_CHIPID	S3C_ADDR(0x02000000)
+
 static struct platform_device exynos_cpuidle = {
 	.name              = "exynos_cpuidle",
 #ifdef CONFIG_ARM_EXYNOS_CPUIDLE
@@ -36,6 +37,14 @@ void __iomem *sysram_base_addr __ro_after_init;
 phys_addr_t sysram_base_phys __ro_after_init;
 void __iomem *sysram_ns_base_addr __ro_after_init;
 
+unsigned long exynos_cpu_id;
+static unsigned int exynos_cpu_rev;
+
+unsigned int exynos_rev(void)
+{
+	return exynos_cpu_rev;
+}
+
 void __init exynos_sysram_init(void)
 {
 	struct device_node *node;
@@ -86,7 +95,11 @@ static void __init exynos_init_io(void)
 	of_scan_flat_dt(exynos_fdt_map_chipid, NULL);
 
 	/* detect cpu id and rev. */
-	s5p_init_cpu(S5P_VA_CHIPID);
+	exynos_cpu_id = readl_relaxed(S5P_VA_CHIPID);
+	exynos_cpu_rev = exynos_cpu_id & 0xFF;
+
+	pr_info("Samsung CPU ID: 0x%08lx\n", exynos_cpu_id);
+
 }
 
 /*
@@ -193,8 +206,8 @@ static void __init exynos_dt_fixup(void)
 }
 
 DT_MACHINE_START(EXYNOS_DT, "Samsung Exynos (Flattened Device Tree)")
-	.l2c_aux_val	= 0x3c400000,
-	.l2c_aux_mask	= 0xc20fffff,
+	.l2c_aux_val	= 0x38400000,
+	.l2c_aux_mask	= 0xc60fffff,
 	.smp		= smp_ops(exynos_smp_ops),
 	.map_io		= exynos_init_io,
 	.init_early	= exynos_firmware_init,
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
deleted file mode 100644
index 8d58faa54ff7..000000000000
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * Exynos - Memory map definitions
- */
-
-#ifndef __ASM_ARCH_MAP_H
-#define __ASM_ARCH_MAP_H __FILE__
-
-#include <plat/map-base.h>
-
-#include <plat/map-s5p.h>
-
-#define EXYNOS_PA_CHIPID		0x10000000
-
-#endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c
index 0cbbae8bf1f8..d7fedbb2eefe 100644
--- a/arch/arm/mach-exynos/platsmp.c
+++ b/arch/arm/mach-exynos/platsmp.c
@@ -22,8 +22,6 @@
 #include <asm/smp_scu.h>
 #include <asm/firmware.h>
 
-#include <mach/map.h>
-
 #include "common.h"
 
 extern void exynos4_secondary_startup(void);
@@ -188,7 +186,7 @@ void exynos_scu_enable(void)
 
 static void __iomem *cpu_boot_reg_base(void)
 {
-	if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1)
+	if (soc_is_exynos4210() && exynos_rev() == EXYNOS4210_REV_1_1)
 		return pmu_base_addr + S5P_INFORM5;
 	return sysram_base_addr;
 }
diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
index 78af34cc89cc..30f4e55bf39e 100644
--- a/arch/arm/mach-exynos/pm.c
+++ b/arch/arm/mach-exynos/pm.c
@@ -26,18 +26,18 @@
 
 static inline void __iomem *exynos_boot_vector_addr(void)
 {
-	if (samsung_rev() == EXYNOS4210_REV_1_1)
+	if (exynos_rev() == EXYNOS4210_REV_1_1)
 		return pmu_base_addr + S5P_INFORM7;
-	else if (samsung_rev() == EXYNOS4210_REV_1_0)
+	else if (exynos_rev() == EXYNOS4210_REV_1_0)
 		return sysram_base_addr + 0x24;
 	return pmu_base_addr + S5P_INFORM0;
 }
 
 static inline void __iomem *exynos_boot_vector_flag(void)
 {
-	if (samsung_rev() == EXYNOS4210_REV_1_1)
+	if (exynos_rev() == EXYNOS4210_REV_1_1)
 		return pmu_base_addr + S5P_INFORM6;
-	else if (samsung_rev() == EXYNOS4210_REV_1_0)
+	else if (exynos_rev() == EXYNOS4210_REV_1_0)
 		return sysram_base_addr + 0x20;
 	return pmu_base_addr + S5P_INFORM1;
 }
diff --git a/arch/arm/mach-hisi/Kconfig b/arch/arm/mach-hisi/Kconfig
index 3b010fe7c0e9..2e980f834a6a 100644
--- a/arch/arm/mach-hisi/Kconfig
+++ b/arch/arm/mach-hisi/Kconfig
@@ -1,9 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config ARCH_HISI
 	bool "Hisilicon SoC Support"
-	depends on ARCH_MULTI_V7
+	depends on ARCH_MULTI_V7 || ARCH_MULTI_V5
 	select ARM_AMBA
-	select ARM_GIC
+	select ARM_GIC if ARCH_MULTI_V7
 	select ARM_TIMER_SP804
 	select POWER_RESET
 	select POWER_RESET_HISI
@@ -15,6 +15,7 @@ menu "Hisilicon platform type"
 
 config ARCH_HI3xxx
 	bool "Hisilicon Hi36xx family"
+	depends on ARCH_MULTI_V7
 	select CACHE_L2X0
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
@@ -25,6 +26,7 @@ config ARCH_HI3xxx
 
 config ARCH_HIP01
 	bool "Hisilicon HIP01 family"
+	depends on ARCH_MULTI_V7
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select ARM_GLOBAL_TIMER
@@ -33,6 +35,7 @@ config ARCH_HIP01
 
 config ARCH_HIP04
 	bool "Hisilicon HiP04 Cortex A15 family"
+	depends on ARCH_MULTI_V7
 	select ARM_ERRATA_798181 if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select MCPM if SMP
@@ -43,6 +46,7 @@ config ARCH_HIP04
 
 config ARCH_HIX5HD2
 	bool "Hisilicon X5HD2 family"
+	depends on ARCH_MULTI_V7
 	select CACHE_L2X0
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
@@ -50,6 +54,14 @@ config ARCH_HIX5HD2
 	select PINCTRL_SINGLE
 	help
 	  Support for Hisilicon HIX5HD2 SoC family
+
+config ARCH_SD5203
+	bool "Hisilicon SD5203 family"
+	depends on ARCH_MULTI_V5
+	select DW_APB_ICTL
+	help
+	  Support for Hisilicon SD5203 SoC family
+
 endmenu
 
 endif
diff --git a/arch/arm/mach-imx/3ds_debugboard.c b/arch/arm/mach-imx/3ds_debugboard.c
deleted file mode 100644
index 0e018000715a..000000000000
--- a/arch/arm/mach-imx/3ds_debugboard.c
+++ /dev/null
@@ -1,207 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2010 Jason Wang <jason77.wang@gmail.com>
- */
-
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/smsc911x.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include "3ds_debugboard.h"
-#include "hardware.h"
-
-/* LAN9217 ethernet base address */
-#define LAN9217_BASE_ADDR(n)	(n + 0x0)
-/* External UART */
-#define UARTA_BASE_ADDR(n)	(n + 0x8000)
-#define UARTB_BASE_ADDR(n)	(n + 0x10000)
-
-#define BOARD_IO_ADDR(n)	(n + 0x20000)
-/* LED switchs */
-#define LED_SWITCH_REG		0x00
-/* buttons */
-#define SWITCH_BUTTONS_REG	0x08
-/* status, interrupt */
-#define INTR_STATUS_REG	0x10
-#define INTR_MASK_REG		0x38
-#define INTR_RESET_REG		0x20
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER1_REG	0x40
-#define MAGIC_NUMBER2_REG	0x48
-/* CPLD code version */
-#define CPLD_CODE_VER_REG	0x50
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER3_REG	0x58
-/* module reset register*/
-#define MODULE_RESET_REG	0x60
-/* CPU ID and Personality ID */
-#define MCU_BOARD_ID_REG	0x68
-
-#define MXC_MAX_EXP_IO_LINES	16
-
-/* interrupts like external uart , external ethernet etc*/
-#define EXPIO_INT_ENET		0
-#define EXPIO_INT_XUART_A	1
-#define EXPIO_INT_XUART_B	2
-#define EXPIO_INT_BUTTON_A	3
-#define EXPIO_INT_BUTTON_B	4
-
-static void __iomem *brd_io;
-static struct irq_domain *domain;
-
-static struct resource smsc911x_resources[] = {
-	{
-		.flags = IORESOURCE_MEM,
-	} , {
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
-	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
-};
-
-static struct platform_device smsc_lan9217_device = {
-	.name = "smsc911x",
-	.id = -1,
-	.dev = {
-		.platform_data = &smsc911x_config,
-	},
-	.num_resources = ARRAY_SIZE(smsc911x_resources),
-	.resource = smsc911x_resources,
-};
-
-static void mxc_expio_irq_handler(struct irq_desc *desc)
-{
-	u32 imr_val;
-	u32 int_valid;
-	u32 expio_irq;
-
-	/* irq = gpio irq number */
-	desc->irq_data.chip->irq_mask(&desc->irq_data);
-
-	imr_val = imx_readw(brd_io + INTR_MASK_REG);
-	int_valid = imx_readw(brd_io + INTR_STATUS_REG) & ~imr_val;
-
-	expio_irq = 0;
-	for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
-		if ((int_valid & 1) == 0)
-			continue;
-		generic_handle_irq(irq_find_mapping(domain, expio_irq));
-	}
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * Irq is an expio virtual irq number
- */
-static void expio_mask_irq(struct irq_data *d)
-{
-	u16 reg;
-	u32 expio = d->hwirq;
-
-	reg = imx_readw(brd_io + INTR_MASK_REG);
-	reg |= (1 << expio);
-	imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static void expio_ack_irq(struct irq_data *d)
-{
-	u32 expio = d->hwirq;
-
-	imx_writew(1 << expio, brd_io + INTR_RESET_REG);
-	imx_writew(0, brd_io + INTR_RESET_REG);
-	expio_mask_irq(d);
-}
-
-static void expio_unmask_irq(struct irq_data *d)
-{
-	u16 reg;
-	u32 expio = d->hwirq;
-
-	reg = imx_readw(brd_io + INTR_MASK_REG);
-	reg &= ~(1 << expio);
-	imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
-	.irq_ack = expio_ack_irq,
-	.irq_mask = expio_mask_irq,
-	.irq_unmask = expio_unmask_irq,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-int __init mxc_expio_init(u32 base, u32 intr_gpio)
-{
-	u32 p_irq = gpio_to_irq(intr_gpio);
-	int irq_base;
-	int i;
-
-	brd_io = ioremap(BOARD_IO_ADDR(base), SZ_4K);
-	if (brd_io == NULL)
-		return -ENOMEM;
-
-	if ((imx_readw(brd_io + MAGIC_NUMBER1_REG) != 0xAAAA) ||
-	    (imx_readw(brd_io + MAGIC_NUMBER2_REG) != 0x5555) ||
-	    (imx_readw(brd_io + MAGIC_NUMBER3_REG) != 0xCAFE)) {
-		pr_info("3-Stack Debug board not detected\n");
-		iounmap(brd_io);
-		brd_io = NULL;
-		return -ENODEV;
-	}
-
-	pr_info("3-Stack Debug board detected, rev = 0x%04X\n",
-		readw(brd_io + CPLD_CODE_VER_REG));
-
-	/*
-	 * Configure INT line as GPIO input
-	 */
-	gpio_request(intr_gpio, "expio_pirq");
-	gpio_direction_input(intr_gpio);
-
-	/* disable the interrupt and clear the status */
-	imx_writew(0, brd_io + INTR_MASK_REG);
-	imx_writew(0xFFFF, brd_io + INTR_RESET_REG);
-	imx_writew(0, brd_io + INTR_RESET_REG);
-	imx_writew(0x1F, brd_io + INTR_MASK_REG);
-
-	irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
-	WARN_ON(irq_base < 0);
-
-	domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
-				       &irq_domain_simple_ops, NULL);
-	WARN_ON(!domain);
-
-	for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
-		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
-		irq_clear_status_flags(i, IRQ_NOREQUEST);
-	}
-	irq_set_irq_type(p_irq, IRQF_TRIGGER_LOW);
-	irq_set_chained_handler(p_irq, mxc_expio_irq_handler);
-
-	/* Register Lan device on the debugboard */
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
-	smsc911x_resources[0].start = LAN9217_BASE_ADDR(base);
-	smsc911x_resources[0].end = LAN9217_BASE_ADDR(base) + 0x100 - 1;
-	smsc911x_resources[1].start = irq_find_mapping(domain, EXPIO_INT_ENET);
-	smsc911x_resources[1].end = irq_find_mapping(domain, EXPIO_INT_ENET);
-	platform_device_register(&smsc_lan9217_device);
-
-	return 0;
-}
diff --git a/arch/arm/mach-imx/3ds_debugboard.h b/arch/arm/mach-imx/3ds_debugboard.h
deleted file mode 100644
index a4d04d099c61..000000000000
--- a/arch/arm/mach-imx/3ds_debugboard.h
+++ /dev/null
@@ -1,11 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#ifndef __ASM_ARCH_MXC_3DS_DB_H__
-#define __ASM_ARCH_MXC_3DS_DB_H__
-
-extern int __init mxc_expio_init(u32 base, u32 intr_gpio);
-
-#endif /* __ASM_ARCH_MXC_3DS_DB_H__ */
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index e7d7b90e2cf8..52902782cc5f 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -47,371 +47,26 @@ config HAVE_IMX_SRC
 	def_bool y if SMP
 	select ARCH_HAS_RESET_CONTROLLER
 
-config IMX_HAVE_IOMUX_V1
-	bool
+if ARCH_MULTI_V6
 
-config ARCH_MXC_IOMUX_V3
-	bool
-
-config SOC_IMX21
-	bool
-	select CPU_ARM926T
-	select IMX_HAVE_IOMUX_V1
-	select MXC_AVIC
-
-config SOC_IMX27
-	bool
-	select CPU_ARM926T
-	select IMX_HAVE_IOMUX_V1
-	select MXC_AVIC
-	select PINCTRL_IMX27
+comment "ARM1136 platforms"
 
 config SOC_IMX31
-	bool
+	bool "i.MX31 support"
 	select CPU_V6
 	select MXC_AVIC
+	help
+	  This enables support for Freescale i.MX31 processor
 
 config SOC_IMX35
-	bool
-	select ARCH_MXC_IOMUX_V3
+	bool "i.MX35 support"
 	select MXC_AVIC
 	select PINCTRL_IMX35
-
-if ARCH_MULTI_V5
-
-comment "MX21 platforms:"
-
-config MACH_MX21ADS
-	bool "MX21ADS platform"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select SOC_IMX21
-	help
-	  Include support for MX21ADS platform. This includes specific
-	  configurations for the board and its peripherals.
-
-comment "MX27 platforms:"
-
-config MACH_MX27ADS
-	bool "MX27ADS platform"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select SOC_IMX27
-	help
-	  Include support for MX27ADS platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_MX27_3DS
-	bool "MX27PDK platform"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MX2_CAMERA
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select MXC_DEBUG_BOARD
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for MX27PDK platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_IMX27_VISSTRIM_M10
-	bool "Vista Silicon i.MX27 Visstrim_m10"
-	select IMX_HAVE_PLATFORM_GPIO_KEYS
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MX2_CAMERA
-	select IMX_HAVE_PLATFORM_MX2_EMMA
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select LEDS_GPIO_REGISTER
-	select SOC_IMX27
-	help
-	  Include support for Visstrim_m10 platform and its different variants.
-	  This includes specific configurations for the board and its
-	  peripherals.
-
-config MACH_PCA100
-	bool "Phytec phyCARD-s (pca100)"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for phyCARD-s (aka pca100) platform. This
-	  includes specific configurations for the module and its peripherals.
-
-config MACH_IMX27_DT
-	bool "Support i.MX27 platforms from device tree"
-	select SOC_IMX27
-	help
-	  Include support for Freescale i.MX27 based platforms
-	  using the device tree for discovery
-
-endif
-
-if ARCH_MULTI_V6
-
-comment "MX31 platforms:"
-
-config MACH_MX31ADS
-	bool "Support MX31ADS platforms"
-	default y
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select SOC_IMX31
-	help
-	  Include support for MX31ADS platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_MX31ADS_WM1133_EV1
-	bool "Support Wolfson Microelectronics 1133-EV1 module"
-	depends on MACH_MX31ADS
-	depends on MFD_WM8350_I2C
-	depends on REGULATOR_WM8350 = y
 	help
-	  Include support for the Wolfson Microelectronics 1133-EV1 PMU
-	  and audio module for the MX31ADS platform.
-
-config MACH_MX31LILLY
-	bool "Support MX31 LILLY-1131 platforms (INCO startec)"
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for mx31 based LILLY1131 modules. This includes
-	  specific configurations for the board and its peripherals.
-
-config MACH_MX31LITE
-	bool "Support MX31 LITEKIT (LogicPD)"
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_RTC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select LEDS_GPIO_REGISTER
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for MX31 LITEKIT platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_PCM037
-	bool "Support Phytec pcm037 (i.MX31) platforms"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for Phytec pcm037 platform. This includes
-	  specific configurations for the board and its peripherals.
-
-config MACH_PCM037_EET
-	bool "Support pcm037 EET board extensions"
-	depends on MACH_PCM037
-	select IMX_HAVE_PLATFORM_GPIO_KEYS
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	help
-	  Add support for PCM037 EET baseboard extensions. If you are using the
-	  OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel
-	  command-line parameter.
-
-config MACH_MX31_3DS
-	bool "Support MX31PDK (3DS)"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select MXC_DEBUG_BOARD
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for MX31PDK (3DS) platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_MX31_3DS_MXC_NAND_USE_BBT
-	bool "Make the MXC NAND driver use the in flash Bad Block Table"
-	depends on MACH_MX31_3DS
-	depends on MTD_NAND_MXC
-	help
-	  Enable this if you want that the MXC NAND driver uses the in flash
-	  Bad Block Table to know what blocks are bad instead of scanning the
-	  entire flash looking for bad block markers.
-
-config MACH_MX31MOBOARD
-	bool "Support mx31moboard platforms (EPFL Mobots group)"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select LEDS_GPIO_REGISTER
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for mx31moboard platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_QONG
-	bool "Support Dave/DENX QongEVB-LITE platform"
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select SOC_IMX31
-	help
-	  Include support for Dave/DENX QongEVB-LITE platform. This includes
-	  specific configurations for the board and its peripherals.
-
-config MACH_ARMADILLO5X0
-	bool "Support Atmark Armadillo-500 Development Base Board"
-	select IMX_HAVE_PLATFORM_GPIO_KEYS
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX31
-	help
-	  Include support for Atmark Armadillo-500 platform. This includes
-	  specific configurations for the board and its peripherals.
-
-config MACH_KZM_ARM11_01
-	bool "Support KZM-ARM11-01(Kyoto Microcomputer)"
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select SOC_IMX31
-	help
-	  Include support for KZM-ARM11-01. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_BUG
-	bool "Support Buglabs BUGBase platform"
-	default y
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select SOC_IMX31
-	help
-	  Include support for BUGBase 1.3 platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_IMX31_DT
-	bool "Support i.MX31 platforms from device tree"
-	select SOC_IMX31
-	help
-	  Include support for Freescale i.MX31 based platforms
-	  using the device tree for discovery.
-
-comment "MX35 platforms:"
-
-config MACH_IMX35_DT
-	bool "Support i.MX35 platforms from device tree"
-	select SOC_IMX35
-	help
-	  Include support for Freescale i.MX35 based platforms
-	  using the device tree for discovery.
-
-config MACH_PCM043
-	bool "Support Phytec pcm043 (i.MX35) platforms"
-	select IMX_HAVE_PLATFORM_FLEXCAN
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX35
-	help
-	  Include support for Phytec pcm043 platform. This includes
-	  specific configurations for the board and its peripherals.
-
-config MACH_MX35_3DS
-	bool "Support MX35PDK platform"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_RTC
-	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	select MXC_DEBUG_BOARD
-	select SOC_IMX35
-	help
-	  Include support for MX35PDK platform. This includes specific
-	  configurations for the board and its peripherals.
-
-config MACH_VPR200
-	bool "Support VPR200 platform"
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_GPIO_KEYS
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_IPU_CORE
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	select SOC_IMX35
-	help
-	  Include support for VPR200 platform. This includes specific
-	  configurations for the board and its peripherals.
+	  This enables support for Freescale i.MX31 processor
 
 endif
 
-comment "Device tree only"
-
 if ARCH_MULTI_V4T
 
 config SOC_IMX1
@@ -428,12 +83,20 @@ if ARCH_MULTI_V5
 
 config SOC_IMX25
 	bool "i.MX25 support"
-	select ARCH_MXC_IOMUX_V3
 	select CPU_ARM926T
 	select MXC_AVIC
 	select PINCTRL_IMX25
 	help
 	  This enables support for Freescale i.MX25 processor
+
+config SOC_IMX27
+	bool "i.MX27 support"
+	select CPU_ARM926T
+	select MXC_AVIC
+	select PINCTRL_IMX27
+	help
+	  This enables support for Freescale i.MX27 processor
+
 endif
 
 if ARCH_MULTI_V7
@@ -541,10 +204,10 @@ config SOC_LS1021A
 
 endif
 
-comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
-
 if ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
 
+comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
+
 config SOC_IMX7D_CA7
 	bool
 	select ARM_GIC
@@ -607,6 +270,4 @@ endchoice
 
 endif
 
-source "arch/arm/mach-imx/devices/Kconfig"
-
 endif
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index e7364e6c8c6b..9cebd360d58e 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -1,22 +1,16 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-y := cpu.o system.o irq-common.o
 
-obj-$(CONFIG_SOC_IMX21) += mm-imx21.o
-
 obj-$(CONFIG_SOC_IMX25) += cpu-imx25.o mach-imx25.o pm-imx25.o
 
-obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
-obj-$(CONFIG_SOC_IMX27) += mm-imx27.o ehci-imx27.o
+obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o mach-imx27.o
 
-obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o iomux-imx31.o ehci-imx31.o
-obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o ehci-imx35.o
+obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o mach-imx31.o
+obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o mach-imx35.o
 
 imx5-pm-$(CONFIG_PM) += pm-imx5.o
 obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o $(imx5-pm-y)
 
-obj-$(CONFIG_IMX_HAVE_IOMUX_V1) += iomux-v1.o
-obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
-
 obj-$(CONFIG_MXC_TZIC) += tzic.o
 obj-$(CONFIG_MXC_AVIC) += avic.o
 
@@ -37,37 +31,6 @@ obj-y += ssi-fiq.o
 obj-y += ssi-fiq-ksym.o
 endif
 
-# i.MX21 based machines
-obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o
-
-# i.MX27 based machines
-obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
-obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
-obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o
-obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
-obj-$(CONFIG_MACH_IMX27_DT) += imx27-dt.o
-
-# i.MX31 based machines
-obj-$(CONFIG_MACH_MX31ADS) += mach-mx31ads.o
-obj-$(CONFIG_MACH_MX31LILLY) += mach-mx31lilly.o mx31lilly-db.o
-obj-$(CONFIG_MACH_MX31LITE) += mach-mx31lite.o mx31lite-db.o
-obj-$(CONFIG_MACH_PCM037) += mach-pcm037.o
-obj-$(CONFIG_MACH_PCM037_EET) += mach-pcm037_eet.o
-obj-$(CONFIG_MACH_MX31_3DS) += mach-mx31_3ds.o
-obj-$(CONFIG_MACH_MX31MOBOARD) += mach-mx31moboard.o mx31moboard-devboard.o \
-		mx31moboard-marxbot.o mx31moboard-smartbot.o
-obj-$(CONFIG_MACH_QONG) += mach-qong.o
-obj-$(CONFIG_MACH_ARMADILLO5X0) += mach-armadillo5x0.o
-obj-$(CONFIG_MACH_KZM_ARM11_01) += mach-kzm_arm11_01.o
-obj-$(CONFIG_MACH_BUG) += mach-bug.o
-obj-$(CONFIG_MACH_IMX31_DT) += imx31-dt.o
-
-# i.MX35 based machines
-obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o
-obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35_3ds.o
-obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
-obj-$(CONFIG_MACH_IMX35_DT) += imx35-dt.o
-
 obj-$(CONFIG_HAVE_IMX_ANATOP) += anatop.o
 obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
 obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
@@ -105,5 +68,3 @@ obj-$(CONFIG_SOC_IMX53) += mach-imx53.o
 obj-$(CONFIG_SOC_VF610) += mach-vf610.o
 
 obj-$(CONFIG_SOC_LS1021A) += mach-ls1021a.o
-
-obj-y += devices/
diff --git a/arch/arm/mach-imx/board-mx31lilly.h b/arch/arm/mach-imx/board-mx31lilly.h
deleted file mode 100644
index 3508c598c588..000000000000
--- a/arch/arm/mach-imx/board-mx31lilly.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- *   Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lilly_boards {
-	MX31LILLY_NOBOARD	= 0,
-	MX31LILLY_DB		= 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lilly_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LILLY_H__ */
diff --git a/arch/arm/mach-imx/board-mx31lite.h b/arch/arm/mach-imx/board-mx31lite.h
deleted file mode 100644
index 7d7c6219b25f..000000000000
--- a/arch/arm/mach-imx/board-mx31lite.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- *   Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lite_boards {
-	MX31LITE_NOBOARD	= 0,
-	MX31LITE_DB		= 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lite_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LITE_H__ */
diff --git a/arch/arm/mach-imx/board-mx31moboard.h b/arch/arm/mach-imx/board-mx31moboard.h
deleted file mode 100644
index 6f3ff4d4ebc1..000000000000
--- a/arch/arm/mach-imx/board-mx31moboard.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-#define __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31moboard_boards {
-	MX31NOBOARD	= 0,
-	MX31DEVBOARD	= 1,
-	MX31MARXBOT	= 2,
-	MX31SMARTBOT	= 3,
-	MX31EYEBOT	= 4,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31moboard_devboard_init(void);
-extern void mx31moboard_marxbot_init(void);
-extern void mx31moboard_smartbot_init(int board);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__ */
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 72c3fcc32910..2d76e2c6c99e 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -17,29 +17,14 @@ struct device_node;
 enum mxc_cpu_pwr_mode;
 struct of_device_id;
 
-void mx21_map_io(void);
-void mx27_map_io(void);
 void mx31_map_io(void);
 void mx35_map_io(void);
 void imx21_init_early(void);
-void imx27_init_early(void);
 void imx31_init_early(void);
 void imx35_init_early(void);
 void mxc_init_irq(void __iomem *);
-void mx21_init_irq(void);
-void mx27_init_irq(void);
 void mx31_init_irq(void);
 void mx35_init_irq(void);
-void imx21_soc_init(void);
-void imx27_soc_init(void);
-void imx31_soc_init(void);
-void imx35_soc_init(void);
-int mx21_clocks_init(unsigned long lref, unsigned long fref);
-int mx27_clocks_init(unsigned long fref);
-int mx31_clocks_init(unsigned long fref);
-int mx35_clocks_init(void);
-struct platform_device *mxc_register_gpio(char *name, int id,
-	resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
 void mxc_set_cpu_type(unsigned int type);
 void mxc_restart(enum reboot_mode, const char *);
 void mxc_arch_reset_init(void __iomem *);
diff --git a/arch/arm/mach-imx/cpu-imx27.c b/arch/arm/mach-imx/cpu-imx27.c
index a969aa71b60f..bf70e13bbe9e 100644
--- a/arch/arm/mach-imx/cpu-imx27.c
+++ b/arch/arm/mach-imx/cpu-imx27.c
@@ -9,6 +9,7 @@
  */
 
 #include <linux/io.h>
+#include <linux/of_address.h>
 #include <linux/module.h>
 
 #include "hardware.h"
@@ -17,16 +18,23 @@ static int mx27_cpu_rev = -1;
 static int mx27_cpu_partnumber;
 
 #define SYS_CHIP_ID             0x00    /* The offset of CHIP ID register */
+#define SYSCTRL_OFFSET		0x800	/* Offset from CCM base address */
 
 static int mx27_read_cpu_rev(void)
 {
+	void __iomem *ccm_base;
+	struct device_node *np;
 	u32 val;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
+	ccm_base = of_iomap(np, 0);
+	BUG_ON(!ccm_base);
 	/*
 	 * now we have access to the IO registers. As we need
 	 * the silicon revision very early we read it here to
 	 * avoid any further hooks
 	*/
-	val = imx_readl(MX27_IO_ADDRESS(MX27_SYSCTRL_BASE_ADDR + SYS_CHIP_ID));
+	val = imx_readl(ccm_base + SYSCTRL_OFFSET + SYS_CHIP_ID);
 
 	mx27_cpu_partnumber = (int)((val >> 12) & 0xFFFF);
 
diff --git a/arch/arm/mach-imx/cpu-imx31.c b/arch/arm/mach-imx/cpu-imx31.c
index 3ee684b71006..b9c24b851d1a 100644
--- a/arch/arm/mach-imx/cpu-imx31.c
+++ b/arch/arm/mach-imx/cpu-imx31.c
@@ -6,6 +6,7 @@
  */
 
 #include <linux/module.h>
+#include <linux/of_address.h>
 #include <linux/io.h>
 
 #include "common.h"
@@ -32,10 +33,16 @@ static struct {
 
 static int mx31_read_cpu_rev(void)
 {
+	void __iomem *iim_base;
+	struct device_node *np;
 	u32 i, srev;
 
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-iim");
+	iim_base = of_iomap(np, 0);
+	BUG_ON(!iim_base);
+
 	/* read SREV register from IIM module */
-	srev = imx_readl(MX31_IO_ADDRESS(MX31_IIM_BASE_ADDR + MXC_IIMSREV));
+	srev = imx_readl(iim_base + MXC_IIMSREV);
 	srev &= 0xff;
 
 	for (i = 0; i < ARRAY_SIZE(mx31_cpu_type); i++)
diff --git a/arch/arm/mach-imx/cpu-imx35.c b/arch/arm/mach-imx/cpu-imx35.c
index ebb3cdabd506..80e7d8ab9f1b 100644
--- a/arch/arm/mach-imx/cpu-imx35.c
+++ b/arch/arm/mach-imx/cpu-imx35.c
@@ -5,6 +5,7 @@
  * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
  */
 #include <linux/module.h>
+#include <linux/of_address.h>
 #include <linux/io.h>
 
 #include "hardware.h"
@@ -14,9 +15,15 @@ static int mx35_cpu_rev = -1;
 
 static int mx35_read_cpu_rev(void)
 {
+	void __iomem *iim_base;
+	struct device_node *np;
 	u32 rev;
 
-	rev = imx_readl(MX35_IO_ADDRESS(MX35_IIM_BASE_ADDR + MXC_IIMSREV));
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-iim");
+	iim_base = of_iomap(np, 0);
+	BUG_ON(!iim_base);
+
+	rev = imx_readl(iim_base + MXC_IIMSREV);
 	switch (rev) {
 	case 0x00:
 		return IMX_CHIP_REVISION_1_0;
diff --git a/arch/arm/mach-imx/devices-imx21.h b/arch/arm/mach-imx/devices-imx21.h
deleted file mode 100644
index 3679d1de84d4..000000000000
--- a/arch/arm/mach-imx/devices-imx21.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_imx21_hcd_data imx21_imx21_hcd_data;
-#define imx21_add_imx21_hcd(pdata)	\
-	imx_add_imx21_hcd(&imx21_imx21_hcd_data, pdata)
-
-extern const struct imx_imx2_wdt_data imx21_imx2_wdt_data;
-#define imx21_add_imx2_wdt()	\
-	imx_add_imx2_wdt(&imx21_imx2_wdt_data)
-
-extern const struct imx_imx_fb_data imx21_imx_fb_data;
-#define imx21_add_imx_fb(pdata)	\
-	imx_add_imx_fb(&imx21_imx_fb_data, pdata)
-
-extern const struct imx_imx_i2c_data imx21_imx_i2c_data;
-#define imx21_add_imx_i2c(pdata)	\
-	imx_add_imx_i2c(&imx21_imx_i2c_data, pdata)
-
-extern const struct imx_imx_keypad_data imx21_imx_keypad_data;
-#define imx21_add_imx_keypad(pdata)	\
-	imx_add_imx_keypad(&imx21_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx21_imx_ssi_data[];
-#define imx21_add_imx_ssi(id, pdata)	\
-	imx_add_imx_ssi(&imx21_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx21_imx_uart_data[];
-#define imx21_add_imx_uart(id, pdata)	\
-	imx_add_imx_uart_1irq(&imx21_imx_uart_data[id], pdata)
-#define imx21_add_imx_uart0(pdata)	imx21_add_imx_uart(0, pdata)
-#define imx21_add_imx_uart1(pdata)	imx21_add_imx_uart(1, pdata)
-#define imx21_add_imx_uart2(pdata)	imx21_add_imx_uart(2, pdata)
-#define imx21_add_imx_uart3(pdata)	imx21_add_imx_uart(3, pdata)
-
-extern const struct imx_mxc_mmc_data imx21_mxc_mmc_data[];
-#define imx21_add_mxc_mmc(id, pdata)	\
-	imx_add_mxc_mmc(&imx21_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx21_mxc_nand_data;
-#define imx21_add_mxc_nand(pdata)	\
-	imx_add_mxc_nand(&imx21_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_w1_data imx21_mxc_w1_data;
-#define imx21_add_mxc_w1()	\
-	imx_add_mxc_w1(&imx21_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx21_cspi_data[];
-#define imx21_add_cspi(id, pdata)	\
-	imx_add_spi_imx(&imx21_cspi_data[id], pdata)
-#define imx21_add_spi_imx0(pdata)	imx21_add_cspi(0, pdata)
-#define imx21_add_spi_imx1(pdata)	imx21_add_cspi(1, pdata)
diff --git a/arch/arm/mach-imx/devices-imx27.h b/arch/arm/mach-imx/devices-imx27.h
deleted file mode 100644
index 583a1d773d68..000000000000
--- a/arch/arm/mach-imx/devices-imx27.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fec_data imx27_fec_data;
-#define imx27_add_fec(pdata)	\
-	imx_add_fec(&imx27_fec_data, pdata)
-
-extern const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data;
-#define imx27_add_fsl_usb2_udc(pdata)	\
-	imx_add_fsl_usb2_udc(&imx27_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_imx27_coda_data imx27_coda_data;
-#define imx27_add_coda()	\
-	imx_add_imx27_coda(&imx27_coda_data)
-
-extern const struct imx_imx2_wdt_data imx27_imx2_wdt_data;
-#define imx27_add_imx2_wdt()	\
-	imx_add_imx2_wdt(&imx27_imx2_wdt_data)
-
-extern const struct imx_imx_fb_data imx27_imx_fb_data;
-#define imx27_add_imx_fb(pdata)	\
-	imx_add_imx_fb(&imx27_imx_fb_data, pdata)
-
-extern const struct imx_imx_i2c_data imx27_imx_i2c_data[];
-#define imx27_add_imx_i2c(id, pdata)	\
-	imx_add_imx_i2c(&imx27_imx_i2c_data[id], pdata)
-
-extern const struct imx_imx_keypad_data imx27_imx_keypad_data;
-#define imx27_add_imx_keypad(pdata)	\
-	imx_add_imx_keypad(&imx27_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx27_imx_ssi_data[];
-#define imx27_add_imx_ssi(id, pdata)    \
-	imx_add_imx_ssi(&imx27_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx27_imx_uart_data[];
-#define imx27_add_imx_uart(id, pdata)	\
-	imx_add_imx_uart_1irq(&imx27_imx_uart_data[id], pdata)
-#define imx27_add_imx_uart0(pdata)	imx27_add_imx_uart(0, pdata)
-#define imx27_add_imx_uart1(pdata)	imx27_add_imx_uart(1, pdata)
-#define imx27_add_imx_uart2(pdata)	imx27_add_imx_uart(2, pdata)
-#define imx27_add_imx_uart3(pdata)	imx27_add_imx_uart(3, pdata)
-#define imx27_add_imx_uart4(pdata)	imx27_add_imx_uart(4, pdata)
-#define imx27_add_imx_uart5(pdata)	imx27_add_imx_uart(5, pdata)
-
-extern const struct imx_mx2_camera_data imx27_mx2_camera_data;
-#define imx27_add_mx2_camera(pdata)	\
-	imx_add_mx2_camera(&imx27_mx2_camera_data, pdata)
-
-extern const struct imx_mx2_emma_data imx27_mx2_emmaprp_data;
-#define imx27_add_mx2_emmaprp()	\
-	imx_add_mx2_emmaprp(&imx27_mx2_emmaprp_data)
-
-extern const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data;
-#define imx27_add_mxc_ehci_otg(pdata)	\
-	imx_add_mxc_ehci(&imx27_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx27_mxc_ehci_hs_data[];
-#define imx27_add_mxc_ehci_hs(id, pdata)	\
-	imx_add_mxc_ehci(&imx27_mxc_ehci_hs_data[id - 1], pdata)
-
-extern const struct imx_mxc_mmc_data imx27_mxc_mmc_data[];
-#define imx27_add_mxc_mmc(id, pdata)	\
-	imx_add_mxc_mmc(&imx27_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx27_mxc_nand_data;
-#define imx27_add_mxc_nand(pdata)	\
-	imx_add_mxc_nand(&imx27_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_w1_data imx27_mxc_w1_data;
-#define imx27_add_mxc_w1()	\
-	imx_add_mxc_w1(&imx27_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx27_cspi_data[];
-#define imx27_add_cspi(id, gtable) \
-	imx_add_spi_imx(&imx27_cspi_data[id], gtable)
-#define imx27_add_spi_imx0(gtable)	imx27_add_cspi(0, gtable)
-#define imx27_add_spi_imx1(gtable)	imx27_add_cspi(1, gtable)
-#define imx27_add_spi_imx2(gtable)	imx27_add_cspi(2, gtable)
-
-extern const struct imx_pata_imx_data imx27_pata_imx_data;
-#define imx27_add_pata_imx() \
-	imx_add_pata_imx(&imx27_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices-imx31.h b/arch/arm/mach-imx/devices-imx31.h
deleted file mode 100644
index f7cc62372532..000000000000
--- a/arch/arm/mach-imx/devices-imx31.h
+++ /dev/null
@@ -1,80 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data;
-#define imx31_add_fsl_usb2_udc(pdata)	\
-	imx_add_fsl_usb2_udc(&imx31_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_imx2_wdt_data imx31_imx2_wdt_data;
-#define imx31_add_imx2_wdt()       \
-	imx_add_imx2_wdt(&imx31_imx2_wdt_data)
-
-extern const struct imx_imx_i2c_data imx31_imx_i2c_data[];
-#define imx31_add_imx_i2c(id, pdata)	\
-	imx_add_imx_i2c(&imx31_imx_i2c_data[id], pdata)
-#define imx31_add_imx_i2c0(pdata)	imx31_add_imx_i2c(0, pdata)
-#define imx31_add_imx_i2c1(pdata)	imx31_add_imx_i2c(1, pdata)
-#define imx31_add_imx_i2c2(pdata)	imx31_add_imx_i2c(2, pdata)
-
-extern const struct imx_imx_keypad_data imx31_imx_keypad_data;
-#define imx31_add_imx_keypad(pdata)	\
-	imx_add_imx_keypad(&imx31_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx31_imx_ssi_data[];
-#define imx31_add_imx_ssi(id, pdata)    \
-	imx_add_imx_ssi(&imx31_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx31_imx_uart_data[];
-#define imx31_add_imx_uart(id, pdata)	\
-	imx_add_imx_uart_1irq(&imx31_imx_uart_data[id], pdata)
-#define imx31_add_imx_uart0(pdata)	imx31_add_imx_uart(0, pdata)
-#define imx31_add_imx_uart1(pdata)	imx31_add_imx_uart(1, pdata)
-#define imx31_add_imx_uart2(pdata)	imx31_add_imx_uart(2, pdata)
-#define imx31_add_imx_uart3(pdata)	imx31_add_imx_uart(3, pdata)
-#define imx31_add_imx_uart4(pdata)	imx31_add_imx_uart(4, pdata)
-
-extern const struct imx_ipu_core_data imx31_ipu_core_data;
-#define imx31_add_ipu_core()		\
-	imx_add_ipu_core(&imx31_ipu_core_data)
-#define imx31_alloc_mx3_camera(pdata)	\
-	imx_alloc_mx3_camera(&imx31_ipu_core_data, pdata)
-#define imx31_add_mx3_sdc_fb(pdata)	\
-	imx_add_mx3_sdc_fb(&imx31_ipu_core_data, pdata)
-
-extern const struct imx_mxc_ehci_data imx31_mxc_ehci_otg_data;
-#define imx31_add_mxc_ehci_otg(pdata)	\
-	imx_add_mxc_ehci(&imx31_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx31_mxc_ehci_hs_data[];
-#define imx31_add_mxc_ehci_hs(id, pdata)	\
-	imx_add_mxc_ehci(&imx31_mxc_ehci_hs_data[id - 1], pdata)
-
-extern const struct imx_mxc_mmc_data imx31_mxc_mmc_data[];
-#define imx31_add_mxc_mmc(id, pdata)	\
-	imx_add_mxc_mmc(&imx31_mxc_mmc_data[id], pdata)
-
-extern const struct imx_mxc_nand_data imx31_mxc_nand_data;
-#define imx31_add_mxc_nand(pdata)	\
-	imx_add_mxc_nand(&imx31_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_rtc_data imx31_mxc_rtc_data;
-#define imx31_add_mxc_rtc()	\
-	imx_add_mxc_rtc(&imx31_mxc_rtc_data)
-
-extern const struct imx_mxc_w1_data imx31_mxc_w1_data;
-#define imx31_add_mxc_w1()	\
-	imx_add_mxc_w1(&imx31_mxc_w1_data)
-
-extern const struct imx_spi_imx_data imx31_cspi_data[];
-#define imx31_add_cspi(id, gtable) \
-	imx_add_spi_imx(&imx31_cspi_data[id], gtable)
-#define imx31_add_spi_imx0(gtable)	imx31_add_cspi(0, gtable)
-#define imx31_add_spi_imx1(gtable)	imx31_add_cspi(1, gtable)
-#define imx31_add_spi_imx2(gtable)	imx31_add_cspi(2, gtable)
-
-extern const struct imx_pata_imx_data imx31_pata_imx_data;
-#define imx31_add_pata_imx() \
-	imx_add_pata_imx(&imx31_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices-imx35.h b/arch/arm/mach-imx/devices-imx35.h
deleted file mode 100644
index 1b1bdadea15b..000000000000
--- a/arch/arm/mach-imx/devices-imx35.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fec_data imx35_fec_data;
-#define imx35_add_fec(pdata)	\
-	imx_add_fec(&imx35_fec_data, pdata)
-
-extern const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data;
-#define imx35_add_fsl_usb2_udc(pdata)	\
-	imx_add_fsl_usb2_udc(&imx35_fsl_usb2_udc_data, pdata)
-
-extern const struct imx_flexcan_data imx35_flexcan_data[];
-#define imx35_add_flexcan(id)	\
-	imx_add_flexcan(&imx35_flexcan_data[id])
-#define imx35_add_flexcan0()		imx35_add_flexcan(0)
-#define imx35_add_flexcan1()		imx35_add_flexcan(1)
-
-extern const struct imx_imx2_wdt_data imx35_imx2_wdt_data;
-#define imx35_add_imx2_wdt()       \
-	imx_add_imx2_wdt(&imx35_imx2_wdt_data)
-
-extern const struct imx_imx_i2c_data imx35_imx_i2c_data[];
-#define imx35_add_imx_i2c(id, pdata)	\
-	imx_add_imx_i2c(&imx35_imx_i2c_data[id], pdata)
-#define imx35_add_imx_i2c0(pdata)	imx35_add_imx_i2c(0, pdata)
-#define imx35_add_imx_i2c1(pdata)	imx35_add_imx_i2c(1, pdata)
-#define imx35_add_imx_i2c2(pdata)	imx35_add_imx_i2c(2, pdata)
-
-extern const struct imx_imx_keypad_data imx35_imx_keypad_data;
-#define imx35_add_imx_keypad(pdata)	\
-	imx_add_imx_keypad(&imx35_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx35_imx_ssi_data[];
-#define imx35_add_imx_ssi(id, pdata)    \
-	imx_add_imx_ssi(&imx35_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx35_imx_uart_data[];
-#define imx35_add_imx_uart(id, pdata)	\
-	imx_add_imx_uart_1irq(&imx35_imx_uart_data[id], pdata)
-#define imx35_add_imx_uart0(pdata)	imx35_add_imx_uart(0, pdata)
-#define imx35_add_imx_uart1(pdata)	imx35_add_imx_uart(1, pdata)
-#define imx35_add_imx_uart2(pdata)	imx35_add_imx_uart(2, pdata)
-
-extern const struct imx_ipu_core_data imx35_ipu_core_data;
-#define imx35_add_ipu_core()		\
-	imx_add_ipu_core(&imx35_ipu_core_data)
-#define imx35_alloc_mx3_camera(pdata)	\
-	imx_alloc_mx3_camera(&imx35_ipu_core_data, pdata)
-#define imx35_add_mx3_sdc_fb(pdata)	\
-	imx_add_mx3_sdc_fb(&imx35_ipu_core_data, pdata)
-
-extern const struct imx_mxc_ehci_data imx35_mxc_ehci_otg_data;
-#define imx35_add_mxc_ehci_otg(pdata)	\
-	imx_add_mxc_ehci(&imx35_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx35_mxc_ehci_hs_data;
-#define imx35_add_mxc_ehci_hs(pdata)	\
-	imx_add_mxc_ehci(&imx35_mxc_ehci_hs_data, pdata)
-
-extern const struct imx_mxc_nand_data imx35_mxc_nand_data;
-#define imx35_add_mxc_nand(pdata)	\
-	imx_add_mxc_nand(&imx35_mxc_nand_data, pdata)
-
-extern const struct imx_mxc_rtc_data imx35_mxc_rtc_data;
-#define imx35_add_mxc_rtc()	\
-	imx_add_mxc_rtc(&imx35_mxc_rtc_data)
-
-extern const struct imx_mxc_w1_data imx35_mxc_w1_data;
-#define imx35_add_mxc_w1()	\
-	imx_add_mxc_w1(&imx35_mxc_w1_data)
-
-extern const struct imx_sdhci_esdhc_imx_data imx35_sdhci_esdhc_imx_data[];
-#define imx35_add_sdhci_esdhc_imx(id, pdata)	\
-	imx_add_sdhci_esdhc_imx(&imx35_sdhci_esdhc_imx_data[id], pdata)
-
-extern const struct imx_spi_imx_data imx35_cspi_data[];
-#define imx35_add_cspi(id, pdata)	\
-	imx_add_spi_imx(&imx35_cspi_data[id], pdata)
-#define imx35_add_spi_imx0(pdata)	imx35_add_cspi(0, pdata)
-#define imx35_add_spi_imx1(pdata)	imx35_add_cspi(1, pdata)
-
-extern const struct imx_pata_imx_data imx35_pata_imx_data;
-#define imx35_add_pata_imx() \
-	imx_add_pata_imx(&imx35_pata_imx_data)
diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig
deleted file mode 100644
index fdca73d117e6..000000000000
--- a/arch/arm/mach-imx/devices/Kconfig
+++ /dev/null
@@ -1,71 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-config IMX_HAVE_PLATFORM_FEC
-	bool
-	default y if SOC_IMX25 || SOC_IMX27 || SOC_IMX35
-
-config IMX_HAVE_PLATFORM_FLEXCAN
-	bool
-
-config IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	bool
-
-config IMX_HAVE_PLATFORM_GPIO_KEYS
-	bool
-
-config IMX_HAVE_PLATFORM_IMX21_HCD
-	bool
-
-config IMX_HAVE_PLATFORM_IMX27_CODA
-	bool
-	default y if SOC_IMX27
-
-config IMX_HAVE_PLATFORM_IMX2_WDT
-	bool
-
-config IMX_HAVE_PLATFORM_IMX_FB
-	bool
-
-config IMX_HAVE_PLATFORM_IMX_I2C
-	bool
-
-config IMX_HAVE_PLATFORM_IMX_KEYPAD
-	bool
-
-config IMX_HAVE_PLATFORM_PATA_IMX
-	bool
-
-config IMX_HAVE_PLATFORM_IMX_SSI
-	bool
-
-config IMX_HAVE_PLATFORM_IMX_UART
-	bool
-
-config IMX_HAVE_PLATFORM_IPU_CORE
-	bool
-
-config IMX_HAVE_PLATFORM_MX2_CAMERA
-	bool
-
-config IMX_HAVE_PLATFORM_MX2_EMMA
-	bool
-
-config IMX_HAVE_PLATFORM_MXC_EHCI
-	bool
-
-config IMX_HAVE_PLATFORM_MXC_MMC
-	bool
-
-config IMX_HAVE_PLATFORM_MXC_NAND
-	bool
-
-config IMX_HAVE_PLATFORM_MXC_RTC
-	bool
-
-config IMX_HAVE_PLATFORM_MXC_W1
-	bool
-
-config IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	bool
-
-config IMX_HAVE_PLATFORM_SPI_IMX
-	bool
diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile
deleted file mode 100644
index e44758aaa11c..000000000000
--- a/arch/arm/mach-imx/devices/Makefile
+++ /dev/null
@@ -1,28 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-obj-y := devices.o
-
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FEC) += platform-fec.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FLEXCAN) += platform-flexcan.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_FSL_USB2_UDC) += platform-fsl-usb2-udc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_GPIO_KEYS) += platform-gpio_keys.o
-obj-y += platform-gpio-mxc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX21_HCD) += platform-imx21-hcd.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX27_CODA) += platform-imx27-coda.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT) += platform-imx2-wdt.o
-obj-y += platform-imx-dma.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_FB) += platform-imx-fb.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_I2C) += platform-imx-i2c.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_KEYPAD) += platform-imx-keypad.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_PATA_IMX) += platform-pata_imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_SSI) += platform-imx-ssi.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_UART) += platform-imx-uart.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IPU_CORE) += platform-ipu-core.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_CAMERA) += platform-mx2-camera.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_EHCI) += platform-mxc-ehci.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_MMC) += platform-mxc-mmc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_NAND) += platform-mxc_nand.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_RTC) += platform-mxc_rtc.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) +=  platform-spi_imx.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_EMMA) += platform-mx2-emma.o
diff --git a/arch/arm/mach-imx/devices/devices-common.h b/arch/arm/mach-imx/devices/devices-common.h
deleted file mode 100644
index 327a1de7dce1..000000000000
--- a/arch/arm/mach-imx/devices/devices-common.h
+++ /dev/null
@@ -1,293 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_data/dma-imx-sdma.h>
-
-extern struct device mxc_aips_bus;
-extern struct device mxc_ahb_bus;
-
-static inline struct platform_device *imx_add_platform_device_dmamask(
-		const char *name, int id,
-		const struct resource *res, unsigned int num_resources,
-		const void *data, size_t size_data, u64 dmamask)
-{
-	struct platform_device_info pdevinfo = {
-		.name = name,
-		.id = id,
-		.res = res,
-		.num_res = num_resources,
-		.data = data,
-		.size_data = size_data,
-		.dma_mask = dmamask,
-	};
-	return platform_device_register_full(&pdevinfo);
-}
-
-static inline struct platform_device *imx_add_platform_device(
-		const char *name, int id,
-		const struct resource *res, unsigned int num_resources,
-		const void *data, size_t size_data)
-{
-	return imx_add_platform_device_dmamask(
-			name, id, res, num_resources, data, size_data, 0);
-}
-
-#include <linux/fec.h>
-struct imx_fec_data {
-	const char *devid;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_fec(
-		const struct imx_fec_data *data,
-		const struct fec_platform_data *pdata);
-
-struct imx_flexcan_data {
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_flexcan(
-		const struct imx_flexcan_data *data);
-
-#include <linux/fsl_devices.h>
-struct imx_fsl_usb2_udc_data {
-	const char *devid;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_fsl_usb2_udc(
-		const struct imx_fsl_usb2_udc_data *data,
-		const struct fsl_usb2_platform_data *pdata);
-
-#include <linux/gpio_keys.h>
-struct platform_device *__init imx_add_gpio_keys(
-		const struct gpio_keys_platform_data *pdata);
-
-#include <linux/platform_data/usb-mx2.h>
-struct imx_imx21_hcd_data {
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx21_hcd(
-		const struct imx_imx21_hcd_data *data,
-		const struct mx21_usbh_platform_data *pdata);
-
-struct imx_imx27_coda_data {
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx27_coda(
-		const struct imx_imx27_coda_data *data);
-
-struct imx_imx2_wdt_data {
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-};
-struct platform_device *__init imx_add_imx2_wdt(
-		const struct imx_imx2_wdt_data *data);
-
-struct imx_imxdi_rtc_data {
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imxdi_rtc(
-		const struct imx_imxdi_rtc_data *data);
-
-#include <linux/platform_data/video-imxfb.h>
-struct imx_imx_fb_data {
-	const char *devid;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_fb(
-		const struct imx_imx_fb_data *data,
-		const struct imx_fb_platform_data *pdata);
-
-#include <linux/platform_data/i2c-imx.h>
-struct imx_imx_i2c_data {
-	const char *devid;
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_i2c(
-		const struct imx_imx_i2c_data *data,
-		const struct imxi2c_platform_data *pdata);
-
-#include <linux/input/matrix_keypad.h>
-struct imx_imx_keypad_data {
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_keypad(
-		const struct imx_imx_keypad_data *data,
-		const struct matrix_keymap_data *pdata);
-
-#include <linux/platform_data/asoc-imx-ssi.h>
-struct imx_imx_ssi_data {
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-	resource_size_t dmatx0;
-	resource_size_t dmarx0;
-	resource_size_t dmatx1;
-	resource_size_t dmarx1;
-};
-struct platform_device *__init imx_add_imx_ssi(
-		const struct imx_imx_ssi_data *data,
-		const struct imx_ssi_platform_data *pdata);
-
-#include <linux/platform_data/serial-imx.h>
-struct imx_imx_uart_1irq_data {
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_imx_uart_1irq(
-		const struct imx_imx_uart_1irq_data *data,
-		const struct imxuart_platform_data *pdata);
-
-#include <linux/platform_data/video-mx3fb.h>
-#include <linux/platform_data/media/camera-mx3.h>
-struct imx_ipu_core_data {
-	resource_size_t iobase;
-	resource_size_t synirq;
-	resource_size_t errirq;
-};
-struct platform_device *__init imx_add_ipu_core(
-		const struct imx_ipu_core_data *data);
-struct platform_device *__init imx_alloc_mx3_camera(
-		const struct imx_ipu_core_data *data,
-		const struct mx3_camera_pdata *pdata);
-struct platform_device *__init imx_add_mx3_sdc_fb(
-		const struct imx_ipu_core_data *data,
-		struct mx3fb_platform_data *pdata);
-
-#include <linux/platform_data/media/camera-mx2.h>
-struct imx_mx2_camera_data {
-	const char *devid;
-	resource_size_t iobasecsi;
-	resource_size_t iosizecsi;
-	resource_size_t irqcsi;
-	resource_size_t iobaseemmaprp;
-	resource_size_t iosizeemmaprp;
-	resource_size_t irqemmaprp;
-};
-struct platform_device *__init imx_add_mx2_camera(
-		const struct imx_mx2_camera_data *data,
-		const struct mx2_camera_platform_data *pdata);
-
-
-struct imx_mx2_emma_data {
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_mx2_emmaprp(
-		const struct imx_mx2_emma_data *data);
-
-#include <linux/platform_data/usb-ehci-mxc.h>
-struct imx_mxc_ehci_data {
-	int id;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_ehci(
-		const struct imx_mxc_ehci_data *data,
-		const struct mxc_usbh_platform_data *pdata);
-
-#include <linux/platform_data/mmc-mxcmmc.h>
-struct imx_mxc_mmc_data {
-	const char *devid;
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-	resource_size_t dmareq;
-};
-struct platform_device *__init imx_add_mxc_mmc(
-		const struct imx_mxc_mmc_data *data,
-		const struct imxmmc_platform_data *pdata);
-
-#include <linux/platform_data/mtd-mxc_nand.h>
-struct imx_mxc_nand_data {
-	const char *devid;
-	/*
-	 * id is traditionally 0, but -1 is more appropriate.  We use -1 for new
-	 * machines but don't change existing devices as the nand device usually
-	 * appears in the kernel command line to pass its partitioning.
-	 */
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t axibase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_nand(
-		const struct imx_mxc_nand_data *data,
-		const struct mxc_nand_platform_data *pdata);
-
-struct imx_pata_imx_data {
-	resource_size_t iobase;
-	resource_size_t iosize;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_pata_imx(
-		const struct imx_pata_imx_data *data);
-
-/* mxc_rtc */
-struct imx_mxc_rtc_data {
-	const char *devid;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_mxc_rtc(
-		const struct imx_mxc_rtc_data *data);
-
-/* mxc_w1 */
-struct imx_mxc_w1_data {
-	resource_size_t iobase;
-};
-struct platform_device *__init imx_add_mxc_w1(
-		const struct imx_mxc_w1_data *data);
-
-#include <linux/platform_data/mmc-esdhc-imx.h>
-struct imx_sdhci_esdhc_imx_data {
-	const char *devid;
-	int id;
-	resource_size_t iobase;
-	resource_size_t irq;
-};
-struct platform_device *__init imx_add_sdhci_esdhc_imx(
-		const struct imx_sdhci_esdhc_imx_data *data,
-		const struct esdhc_platform_data *pdata);
-
-struct imx_spi_imx_data {
-	const char *devid;
-	int id;
-	resource_size_t iobase;
-	resource_size_t iosize;
-	int irq;
-};
-struct platform_device *__init imx_add_spi_imx(
-	const struct imx_spi_imx_data *data, struct gpiod_lookup_table *gtable);
-
-struct platform_device *imx_add_imx_dma(char *name, resource_size_t iobase,
-					int irq);
-struct platform_device *imx_add_imx_sdma(char *name,
-	resource_size_t iobase, int irq, struct sdma_platform_data *pdata);
diff --git a/arch/arm/mach-imx/devices/devices.c b/arch/arm/mach-imx/devices/devices.c
deleted file mode 100644
index cd72f0894196..000000000000
--- a/arch/arm/mach-imx/devices/devices.c
+++ /dev/null
@@ -1,35 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008 Sascha Hauer, kernel@pengutronix.de
- */
-
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/err.h>
-#include <linux/platform_device.h>
-
-#include "../common.h"
-#include "devices-common.h"
-
-struct device mxc_aips_bus = {
-	.init_name	= "mxc_aips",
-};
-
-struct device mxc_ahb_bus = {
-	.init_name	= "mxc_ahb",
-};
-
-int __init mxc_device_init(void)
-{
-	int ret;
-
-	ret = device_register(&mxc_aips_bus);
-	if (ret < 0)
-		goto done;
-
-	ret = device_register(&mxc_ahb_bus);
-
-done:
-	return ret;
-}
diff --git a/arch/arm/mach-imx/devices/platform-fec.c b/arch/arm/mach-imx/devices/platform-fec.c
deleted file mode 100644
index 88e853d7fb01..000000000000
--- a/arch/arm/mach-imx/devices/platform-fec.c
+++ /dev/null
@@ -1,49 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_fec_data_entry_single(soc, _devid)				\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _FEC_BASE_ADDR,			\
-		.irq = soc ## _INT_FEC,					\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_fec_data imx27_fec_data __initconst =
-	imx_fec_data_entry_single(MX27, "imx27-fec");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX35
-/* i.mx35 has the i.mx27 type fec */
-const struct imx_fec_data imx35_fec_data __initconst =
-	imx_fec_data_entry_single(MX35, "imx27-fec");
-#endif
-
-struct platform_device *__init imx_add_fec(
-		const struct imx_fec_data *data,
-		const struct fec_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_4K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device_dmamask(data->devid, 0,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-flexcan.c b/arch/arm/mach-imx/devices/platform-flexcan.c
deleted file mode 100644
index e4eed35c1fe2..000000000000
--- a/arch/arm/mach-imx/devices/platform-flexcan.c
+++ /dev/null
@@ -1,45 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix, Marc Kleine-Budde <kernel@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_flexcan_data_entry_single(soc, _id, _hwid, _size)		\
-	{								\
-		.id = _id,						\
-		.iobase = soc ## _CAN ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irq = soc ## _INT_CAN ## _hwid,			\
-	}
-
-#define imx_flexcan_data_entry(soc, _id, _hwid, _size)			\
-	[_id] = imx_flexcan_data_entry_single(soc, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_flexcan_data imx35_flexcan_data[] __initconst = {
-#define imx35_flexcan_data_entry(_id, _hwid)				\
-	imx_flexcan_data_entry(MX35, _id, _hwid, SZ_16K)
-	imx35_flexcan_data_entry(0, 1),
-	imx35_flexcan_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_flexcan(
-		const struct imx_flexcan_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device("flexcan", data->id,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
deleted file mode 100644
index cc86de4d7acb..000000000000
--- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
+++ /dev/null
@@ -1,51 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_fsl_usb2_udc_data_entry_single(soc, _devid)			\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _USB_OTG_BASE_ADDR,			\
-		.irq = soc ## _INT_USB_OTG,				\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX31, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX35, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_fsl_usb2_udc(
-		const struct imx_fsl_usb2_udc_data *data,
-		const struct fsl_usb2_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_512 - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask(data->devid, -1,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-gpio-mxc.c b/arch/arm/mach-imx/devices/platform-gpio-mxc.c
deleted file mode 100644
index 355de845224c..000000000000
--- a/arch/arm/mach-imx/devices/platform-gpio-mxc.c
+++ /dev/null
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2011 Linaro Limited
- */
-#include "devices-common.h"
-#include "../common.h"
-
-struct platform_device *__init mxc_register_gpio(char *name, int id,
-	resource_size_t iobase, resource_size_t iosize, int irq, int irq_high)
-{
-	struct resource res[] = {
-		{
-			.start = iobase,
-			.end = iobase + iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = irq,
-			.end = irq,
-			.flags = IORESOURCE_IRQ,
-		}, {
-			.start = irq_high,
-			.end = irq_high,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	unsigned int nres;
-
-	nres = irq_high ? ARRAY_SIZE(res) : ARRAY_SIZE(res) - 1;
-	return platform_device_register_resndata(&mxc_aips_bus, name, id, res, nres, NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-gpio_keys.c b/arch/arm/mach-imx/devices/platform-gpio_keys.c
deleted file mode 100644
index 488678403ac8..000000000000
--- a/arch/arm/mach-imx/devices/platform-gpio_keys.c
+++ /dev/null
@@ -1,15 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-struct platform_device *__init imx_add_gpio_keys(
-		const struct gpio_keys_platform_data *pdata)
-{
-	return imx_add_platform_device("gpio-keys", -1, NULL,
-		 0, pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-dma.c b/arch/arm/mach-imx/devices/platform-imx-dma.c
deleted file mode 100644
index 12656f24ad0d..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-dma.c
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "devices-common.h"
-
-struct platform_device __init __maybe_unused *imx_add_imx_dma(char *name,
-	resource_size_t iobase, int irq)
-{
-	struct resource res[] = {
-		{
-			.start = iobase,
-			.end = iobase + SZ_4K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = irq,
-			.end = irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return platform_device_register_resndata(&mxc_ahb_bus,
-			name, -1, res, ARRAY_SIZE(res), NULL, 0);
-}
-
-struct platform_device __init __maybe_unused *imx_add_imx_sdma(char *name,
-	resource_size_t iobase, int irq, struct sdma_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = iobase,
-			.end = iobase + SZ_16K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = irq,
-			.end = irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return platform_device_register_resndata(&mxc_ahb_bus, name,
-			-1, res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c
deleted file mode 100644
index e553d014506a..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-fb.c
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_fb_data_entry_single(soc, _devid, _size)		\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _LCDC_BASE_ADDR,			\
-		.iosize = _size,					\
-		.irq = soc ## _INT_LCDC,				\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_fb_data imx21_imx_fb_data __initconst =
-	imx_imx_fb_data_entry_single(MX21, "imx21-fb", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_fb_data imx27_imx_fb_data __initconst =
-	imx_imx_fb_data_entry_single(MX27, "imx21-fb", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_imx_fb(
-		const struct imx_imx_fb_data *data,
-		const struct imx_fb_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask(data->devid, 0,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-i2c.c b/arch/arm/mach-imx/devices/platform-imx-i2c.c
deleted file mode 100644
index 81d317bfadd8..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-i2c.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_i2c_data_entry_single(soc, _devid, _id, _hwid, _size)	\
-	{								\
-		.devid = _devid,					\
-		.id = _id,						\
-		.iobase = soc ## _I2C ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irq = soc ## _INT_I2C ## _hwid,			\
-	}
-
-#define imx_imx_i2c_data_entry(soc, _devid, _id, _hwid, _size)		\
-	[_id] = imx_imx_i2c_data_entry_single(soc, _devid, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_i2c_data imx21_imx_i2c_data __initconst =
-	imx_imx_i2c_data_entry_single(MX21, "imx21-i2c", 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_i2c_data imx27_imx_i2c_data[] __initconst = {
-#define imx27_imx_i2c_data_entry(_id, _hwid)				\
-	imx_imx_i2c_data_entry(MX27, "imx21-i2c", _id, _hwid, SZ_4K)
-	imx27_imx_i2c_data_entry(0, 1),
-	imx27_imx_i2c_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_i2c_data imx31_imx_i2c_data[] __initconst = {
-#define imx31_imx_i2c_data_entry(_id, _hwid)				\
-	imx_imx_i2c_data_entry(MX31, "imx21-i2c", _id, _hwid, SZ_4K)
-	imx31_imx_i2c_data_entry(0, 1),
-	imx31_imx_i2c_data_entry(1, 2),
-	imx31_imx_i2c_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_i2c_data imx35_imx_i2c_data[] __initconst = {
-#define imx35_imx_i2c_data_entry(_id, _hwid)				\
-	imx_imx_i2c_data_entry(MX35, "imx21-i2c", _id, _hwid, SZ_4K)
-	imx35_imx_i2c_data_entry(0, 1),
-	imx35_imx_i2c_data_entry(1, 2),
-	imx35_imx_i2c_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_i2c(
-		const struct imx_imx_i2c_data *data,
-		const struct imxi2c_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device(data->devid, data->id,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-keypad.c b/arch/arm/mach-imx/devices/platform-imx-keypad.c
deleted file mode 100644
index de2e03ec2d89..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-keypad.c
+++ /dev/null
@@ -1,54 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_keypad_data_entry_single(soc, _size)			\
-	{								\
-		.iobase = soc ## _KPP_BASE_ADDR,			\
-		.iosize = _size,					\
-		.irq = soc ## _INT_KPP,					\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_keypad_data imx21_imx_keypad_data __initconst =
-	imx_imx_keypad_data_entry_single(MX21, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_keypad_data imx27_imx_keypad_data __initconst =
-	imx_imx_keypad_data_entry_single(MX27, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_keypad_data imx31_imx_keypad_data __initconst =
-	imx_imx_keypad_data_entry_single(MX31, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_keypad_data imx35_imx_keypad_data __initconst =
-	imx_imx_keypad_data_entry_single(MX35, SZ_16);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_keypad(
-		const struct imx_imx_keypad_data *data,
-		const struct matrix_keymap_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device("imx-keypad", -1,
-			res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-ssi.c b/arch/arm/mach-imx/devices/platform-imx-ssi.c
deleted file mode 100644
index ed8c66438af0..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-ssi.c
+++ /dev/null
@@ -1,86 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_ssi_data_entry(soc, _id, _hwid, _size)			\
-	[_id] = {							\
-		.id = _id,						\
-		.iobase = soc ## _SSI ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irq = soc ## _INT_SSI ## _hwid,			\
-		.dmatx0 = soc ## _DMA_REQ_SSI ## _hwid ## _TX0,		\
-		.dmarx0 = soc ## _DMA_REQ_SSI ## _hwid ## _RX0,		\
-		.dmatx1 = soc ## _DMA_REQ_SSI ## _hwid ## _TX1,		\
-		.dmarx1 = soc ## _DMA_REQ_SSI ## _hwid ## _RX1,		\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_ssi_data imx21_imx_ssi_data[] __initconst = {
-#define imx21_imx_ssi_data_entry(_id, _hwid)				\
-	imx_imx_ssi_data_entry(MX21, _id, _hwid, SZ_4K)
-	imx21_imx_ssi_data_entry(0, 1),
-	imx21_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_ssi_data imx27_imx_ssi_data[] __initconst = {
-#define imx27_imx_ssi_data_entry(_id, _hwid)				\
-	imx_imx_ssi_data_entry(MX27, _id, _hwid, SZ_4K)
-	imx27_imx_ssi_data_entry(0, 1),
-	imx27_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_ssi_data imx31_imx_ssi_data[] __initconst = {
-#define imx31_imx_ssi_data_entry(_id, _hwid)				\
-	imx_imx_ssi_data_entry(MX31, _id, _hwid, SZ_4K)
-	imx31_imx_ssi_data_entry(0, 1),
-	imx31_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_ssi_data imx35_imx_ssi_data[] __initconst = {
-#define imx35_imx_ssi_data_entry(_id, _hwid)				\
-	imx_imx_ssi_data_entry(MX35, _id, _hwid, SZ_4K)
-	imx35_imx_ssi_data_entry(0, 1),
-	imx35_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_ssi(
-		const struct imx_imx_ssi_data *data,
-		const struct imx_ssi_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-#define DMARES(_name) {							\
-	.name = #_name,							\
-	.start = data->dma ## _name,					\
-	.end = data->dma ## _name,					\
-	.flags = IORESOURCE_DMA,					\
-}
-		DMARES(tx0),
-		DMARES(rx0),
-		DMARES(tx1),
-		DMARES(rx1),
-	};
-
-	return imx_add_platform_device("imx-ssi", data->id,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx-uart.c b/arch/arm/mach-imx/devices/platform-imx-uart.c
deleted file mode 100644
index c8f01deedd80..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx-uart.c
+++ /dev/null
@@ -1,92 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx_uart_3irq_data_entry(soc, _id, _hwid, _size)		\
-	[_id] = {							\
-		.id = _id,						\
-		.iobase = soc ## _UART ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irqrx = soc ## _INT_UART ## _hwid ## RX,		\
-		.irqtx = soc ## _INT_UART ## _hwid ## TX,		\
-		.irqrts = soc ## _INT_UART ## _hwid ## RTS,		\
-	}
-
-#define imx_imx_uart_1irq_data_entry(soc, _id, _hwid, _size)		\
-	[_id] = {							\
-		.id = _id,						\
-		.iobase = soc ## _UART ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irq = soc ## _INT_UART ## _hwid,			\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx_uart_1irq_data imx21_imx_uart_data[] __initconst = {
-#define imx21_imx_uart_data_entry(_id, _hwid)				\
-	imx_imx_uart_1irq_data_entry(MX21, _id, _hwid, SZ_4K)
-	imx21_imx_uart_data_entry(0, 1),
-	imx21_imx_uart_data_entry(1, 2),
-	imx21_imx_uart_data_entry(2, 3),
-	imx21_imx_uart_data_entry(3, 4),
-};
-#endif
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx_uart_1irq_data imx27_imx_uart_data[] __initconst = {
-#define imx27_imx_uart_data_entry(_id, _hwid)				\
-	imx_imx_uart_1irq_data_entry(MX27, _id, _hwid, SZ_4K)
-	imx27_imx_uart_data_entry(0, 1),
-	imx27_imx_uart_data_entry(1, 2),
-	imx27_imx_uart_data_entry(2, 3),
-	imx27_imx_uart_data_entry(3, 4),
-	imx27_imx_uart_data_entry(4, 5),
-	imx27_imx_uart_data_entry(5, 6),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx_uart_1irq_data imx31_imx_uart_data[] __initconst = {
-#define imx31_imx_uart_data_entry(_id, _hwid)				\
-	imx_imx_uart_1irq_data_entry(MX31, _id, _hwid, SZ_4K)
-	imx31_imx_uart_data_entry(0, 1),
-	imx31_imx_uart_data_entry(1, 2),
-	imx31_imx_uart_data_entry(2, 3),
-	imx31_imx_uart_data_entry(3, 4),
-	imx31_imx_uart_data_entry(4, 5),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx_uart_1irq_data imx35_imx_uart_data[] __initconst = {
-#define imx35_imx_uart_data_entry(_id, _hwid)				\
-	imx_imx_uart_1irq_data_entry(MX35, _id, _hwid, SZ_16K)
-	imx35_imx_uart_data_entry(0, 1),
-	imx35_imx_uart_data_entry(1, 2),
-	imx35_imx_uart_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx_uart_1irq(
-		const struct imx_imx_uart_1irq_data *data,
-		const struct imxuart_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	/* i.mx21 type uart runs on all i.mx except i.mx1 */
-	return imx_add_platform_device("imx21-uart", data->id,
-			res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx2-wdt.c b/arch/arm/mach-imx/devices/platform-imx2-wdt.c
deleted file mode 100644
index fdd355ae4d5f..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx2-wdt.c
+++ /dev/null
@@ -1,52 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx2_wdt_data_entry_single(soc, _id, _hwid, _size)		\
-	{								\
-		.id = _id,						\
-		.iobase = soc ## _WDOG ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-	}
-#define imx_imx2_wdt_data_entry(soc, _id, _hwid, _size)			\
-	[_id] = imx_imx2_wdt_data_entry_single(soc, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx2_wdt_data imx21_imx2_wdt_data __initconst =
-	imx_imx2_wdt_data_entry_single(MX21, 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx2_wdt_data imx27_imx2_wdt_data __initconst =
-	imx_imx2_wdt_data_entry_single(MX27, 0, , SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_imx2_wdt_data imx31_imx2_wdt_data __initconst =
-	imx_imx2_wdt_data_entry_single(MX31, 0, , SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_imx2_wdt_data imx35_imx2_wdt_data __initconst =
-	imx_imx2_wdt_data_entry_single(MX35, 0, , SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_imx2_wdt(
-		const struct imx_imx2_wdt_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		},
-	};
-	return imx_add_platform_device("imx2-wdt", data->id,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx21-hcd.c b/arch/arm/mach-imx/devices/platform-imx21-hcd.c
deleted file mode 100644
index f55763c36d26..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx21-hcd.c
+++ /dev/null
@@ -1,38 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imx21_hcd_data_entry_single(soc)				\
-	{								\
-		.iobase = soc ## _USBOTG_BASE_ADDR,			\
-		.irq = soc ## _INT_USBHOST,				\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_imx21_hcd_data imx21_imx21_hcd_data __initconst =
-	imx_imx21_hcd_data_entry_single(MX21);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-struct platform_device *__init imx_add_imx21_hcd(
-		const struct imx_imx21_hcd_data *data,
-		const struct mx21_usbh_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_8K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask("imx21-hcd", 0,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-imx27-coda.c b/arch/arm/mach-imx/devices/platform-imx27-coda.c
deleted file mode 100644
index 66a116e6c6bc..000000000000
--- a/arch/arm/mach-imx/devices/platform-imx27-coda.c
+++ /dev/null
@@ -1,34 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Vista Silicon
- * Javier Martin <javier.martin@vista-silicon.com>
- */
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_imx27_coda_data imx27_coda_data __initconst = {
-	.iobase = MX27_VPU_BASE_ADDR,
-	.iosize = SZ_512,
-	.irq = MX27_INT_VPU,
-};
-#endif
-
-struct platform_device *__init imx_add_imx27_coda(
-		const struct imx_imx27_coda_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask("coda-imx27", 0, res, 2, NULL,
-					0, DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-ipu-core.c b/arch/arm/mach-imx/devices/platform-ipu-core.c
deleted file mode 100644
index b4290760f49f..000000000000
--- a/arch/arm/mach-imx/devices/platform-ipu-core.c
+++ /dev/null
@@ -1,127 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_ipu_core_entry_single(soc)					\
-{									\
-	.iobase = soc ## _IPU_CTRL_BASE_ADDR,				\
-	.synirq = soc ## _INT_IPU_SYN,					\
-	.errirq = soc ## _INT_IPU_ERR,					\
-}
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_ipu_core_data imx31_ipu_core_data __initconst =
-	imx_ipu_core_entry_single(MX31);
-#endif
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_ipu_core_data imx35_ipu_core_data __initconst =
-	imx_ipu_core_entry_single(MX35);
-#endif
-
-static struct platform_device *imx_ipu_coredev __initdata;
-
-struct platform_device *__init imx_add_ipu_core(
-		const struct imx_ipu_core_data *data)
-{
-	/* The resource order is important! */
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + 0x5f,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->iobase + 0x88,
-			.end = data->iobase + 0xb3,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->synirq,
-			.end = data->synirq,
-			.flags = IORESOURCE_IRQ,
-		}, {
-			.start = data->errirq,
-			.end = data->errirq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_ipu_coredev = imx_add_platform_device("ipu-core", -1,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
-
-struct platform_device *__init imx_alloc_mx3_camera(
-		const struct imx_ipu_core_data *data,
-		const struct mx3_camera_pdata *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase + 0x60,
-			.end = data->iobase + 0x87,
-			.flags = IORESOURCE_MEM,
-		},
-	};
-	int ret = -ENOMEM;
-	struct platform_device *pdev;
-
-	if (IS_ERR_OR_NULL(imx_ipu_coredev))
-		return ERR_PTR(-ENODEV);
-
-	pdev = platform_device_alloc("mx3-camera", 0);
-	if (!pdev)
-		return ERR_PTR(-ENOMEM);
-
-	pdev->dev.dma_mask = kmalloc(sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
-	if (!pdev->dev.dma_mask)
-		goto err;
-
-	*pdev->dev.dma_mask = DMA_BIT_MASK(32);
-	pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
-
-	ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res));
-	if (ret)
-		goto err;
-
-	if (pdata) {
-		struct mx3_camera_pdata *copied_pdata;
-
-		ret = platform_device_add_data(pdev, pdata, sizeof(*pdata));
-		if (ret) {
-err:
-			kfree(pdev->dev.dma_mask);
-			platform_device_put(pdev);
-			return ERR_PTR(-ENODEV);
-		}
-		copied_pdata = dev_get_platdata(&pdev->dev);
-		copied_pdata->dma_dev = &imx_ipu_coredev->dev;
-	}
-
-	return pdev;
-}
-
-struct platform_device *__init imx_add_mx3_sdc_fb(
-		const struct imx_ipu_core_data *data,
-		struct mx3fb_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase + 0xb4,
-			.end = data->iobase + 0x1bf,
-			.flags = IORESOURCE_MEM,
-		},
-	};
-
-	if (IS_ERR_OR_NULL(imx_ipu_coredev))
-		return ERR_PTR(-ENODEV);
-
-	pdata->dma_dev = &imx_ipu_coredev->dev;
-
-	return imx_add_platform_device_dmamask("mx3_sdc_fb", -1,
-			res, ARRAY_SIZE(res), pdata, sizeof(*pdata),
-			DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mx2-camera.c b/arch/arm/mach-imx/devices/platform-mx2-camera.c
deleted file mode 100644
index 5375f8b3d079..000000000000
--- a/arch/arm/mach-imx/devices/platform-mx2-camera.c
+++ /dev/null
@@ -1,59 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mx2_camera_data_entry_single(soc, _devid)			\
-	{								\
-		.devid = _devid,					\
-		.iobasecsi = soc ## _CSI_BASE_ADDR,			\
-		.iosizecsi = SZ_4K,					\
-		.irqcsi = soc ## _INT_CSI,				\
-	}
-#define imx_mx2_camera_data_entry_single_emma(soc, _devid)		\
-	{								\
-		.devid = _devid,					\
-		.iobasecsi = soc ## _CSI_BASE_ADDR,			\
-		.iosizecsi = SZ_32,					\
-		.irqcsi = soc ## _INT_CSI,				\
-		.iobaseemmaprp = soc ## _EMMAPRP_BASE_ADDR,		\
-		.iosizeemmaprp = SZ_32,					\
-		.irqemmaprp = soc ## _INT_EMMAPRP,			\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mx2_camera_data imx27_mx2_camera_data __initconst =
-	imx_mx2_camera_data_entry_single_emma(MX27, "imx27-camera");
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_mx2_camera(
-		const struct imx_mx2_camera_data *data,
-		const struct mx2_camera_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobasecsi,
-			.end = data->iobasecsi + data->iosizecsi - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irqcsi,
-			.end = data->irqcsi,
-			.flags = IORESOURCE_IRQ,
-		}, {
-			.start = data->iobaseemmaprp,
-			.end = data->iobaseemmaprp + data->iosizeemmaprp - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irqemmaprp,
-			.end = data->irqemmaprp,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask(data->devid, 0,
-			res, data->iobaseemmaprp ? 4 : 2,
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
-
diff --git a/arch/arm/mach-imx/devices/platform-mx2-emma.c b/arch/arm/mach-imx/devices/platform-mx2-emma.c
deleted file mode 100644
index 20f28ba16f36..000000000000
--- a/arch/arm/mach-imx/devices/platform-mx2-emma.c
+++ /dev/null
@@ -1,37 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mx2_emmaprp_data_entry_single(soc)				\
-	{								\
-		.iobase = soc ## _EMMAPRP_BASE_ADDR,			\
-		.iosize = SZ_256,					\
-		.irq = soc ## _INT_EMMAPRP,				\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mx2_emma_data imx27_mx2_emmaprp_data __initconst =
-	imx_mx2_emmaprp_data_entry_single(MX27);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-struct platform_device *__init imx_add_mx2_emmaprp(
-		const struct imx_mx2_emma_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask("m2m-emmaprp", 0,
-			res, 2, NULL, 0, DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc-ehci.c b/arch/arm/mach-imx/devices/platform-mxc-ehci.c
deleted file mode 100644
index d9d7cc71633f..000000000000
--- a/arch/arm/mach-imx/devices/platform-mxc-ehci.c
+++ /dev/null
@@ -1,61 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_ehci_data_entry_single(soc, _id, hs)			\
-	{								\
-		.id = _id,						\
-		.iobase = soc ## _USB_ ## hs ## _BASE_ADDR,		\
-		.irq = soc ## _INT_USB_ ## hs,				\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX27, 0, OTG);
-const struct imx_mxc_ehci_data imx27_mxc_ehci_hs_data[] __initconst = {
-	imx_mxc_ehci_data_entry_single(MX27, 1, HS1),
-	imx_mxc_ehci_data_entry_single(MX27, 2, HS2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_ehci_data imx31_mxc_ehci_otg_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX31, 0, OTG);
-const struct imx_mxc_ehci_data imx31_mxc_ehci_hs_data[] __initconst = {
-	imx_mxc_ehci_data_entry_single(MX31, 1, HS1),
-	imx_mxc_ehci_data_entry_single(MX31, 2, HS2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_ehci_data imx35_mxc_ehci_otg_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX35, 0, OTG);
-const struct imx_mxc_ehci_data imx35_mxc_ehci_hs_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX35, 1, HS);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_ehci(
-		const struct imx_mxc_ehci_data *data,
-		const struct mxc_usbh_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_512 - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device_dmamask("mxc-ehci", data->id,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc-mmc.c b/arch/arm/mach-imx/devices/platform-mxc-mmc.c
deleted file mode 100644
index cd4c502bc152..000000000000
--- a/arch/arm/mach-imx/devices/platform-mxc-mmc.c
+++ /dev/null
@@ -1,72 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/dma-mapping.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_mmc_data_entry_single(soc, _devid, _id, _hwid, _size)	\
-	{								\
-		.devid = _devid,					\
-		.id = _id,						\
-		.iobase = soc ## _SDHC ## _hwid ## _BASE_ADDR,		\
-		.iosize = _size,					\
-		.irq = soc ## _INT_SDHC ## _hwid,			\
-		.dmareq = soc ## _DMA_REQ_SDHC ## _hwid,		\
-	}
-#define imx_mxc_mmc_data_entry(soc, _devid, _id, _hwid, _size)		\
-	[_id] = imx_mxc_mmc_data_entry_single(soc, _devid, _id, _hwid, _size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_mmc_data imx21_mxc_mmc_data[] __initconst = {
-#define imx21_mxc_mmc_data_entry(_id, _hwid)				\
-	imx_mxc_mmc_data_entry(MX21, "imx21-mmc", _id, _hwid, SZ_4K)
-	imx21_mxc_mmc_data_entry(0, 1),
-	imx21_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_mmc_data imx27_mxc_mmc_data[] __initconst = {
-#define imx27_mxc_mmc_data_entry(_id, _hwid)				\
-	imx_mxc_mmc_data_entry(MX27, "imx21-mmc", _id, _hwid, SZ_4K)
-	imx27_mxc_mmc_data_entry(0, 1),
-	imx27_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_mmc_data imx31_mxc_mmc_data[] __initconst = {
-#define imx31_mxc_mmc_data_entry(_id, _hwid)				\
-	imx_mxc_mmc_data_entry(MX31, "imx31-mmc", _id, _hwid, SZ_16K)
-	imx31_mxc_mmc_data_entry(0, 1),
-	imx31_mxc_mmc_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-struct platform_device *__init imx_add_mxc_mmc(
-		const struct imx_mxc_mmc_data *data,
-		const struct imxmmc_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		}, {
-			.start = data->dmareq,
-			.end = data->dmareq,
-			.flags = IORESOURCE_DMA,
-		},
-	};
-	return imx_add_platform_device_dmamask(data->devid, data->id,
-			res, ARRAY_SIZE(res),
-			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_nand.c b/arch/arm/mach-imx/devices/platform-mxc_nand.c
deleted file mode 100644
index 0f5f741f897f..000000000000
--- a/arch/arm/mach-imx/devices/platform-mxc_nand.c
+++ /dev/null
@@ -1,72 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_nand_data_entry_single(soc, _devid, _size)		\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _NFC_BASE_ADDR,			\
-		.iosize = _size,					\
-		.irq = soc ## _INT_NFC					\
-	}
-
-#define imx_mxc_nandv3_data_entry_single(soc, _devid, _size)		\
-	{								\
-		.devid = _devid,					\
-		.id = -1,						\
-		.iobase = soc ## _NFC_BASE_ADDR,			\
-		.iosize = _size,					\
-		.axibase = soc ## _NFC_AXI_BASE_ADDR,			\
-		.irq = soc ## _INT_NFC					\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_nand_data imx21_mxc_nand_data __initconst =
-	imx_mxc_nand_data_entry_single(MX21, "imx21-nand", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_nand_data imx27_mxc_nand_data __initconst =
-	imx_mxc_nand_data_entry_single(MX27, "imx27-nand", SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_nand_data imx31_mxc_nand_data __initconst =
-	imx_mxc_nand_data_entry_single(MX31, "imx27-nand", SZ_4K);
-#endif
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_nand_data imx35_mxc_nand_data __initconst =
-	imx_mxc_nand_data_entry_single(MX35, "imx25-nand", SZ_8K);
-#endif
-
-struct platform_device *__init imx_add_mxc_nand(
-		const struct imx_mxc_nand_data *data,
-		const struct mxc_nand_platform_data *pdata)
-{
-	/* AXI has to come first, that's how the mxc_nand driver expect it */
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		}, {
-			.start = data->axibase,
-			.end = data->axibase + SZ_16K - 1,
-			.flags = IORESOURCE_MEM,
-		},
-	};
-	return imx_add_platform_device(data->devid, data->id,
-			res, ARRAY_SIZE(res) - !data->axibase,
-			pdata, sizeof(*pdata));
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_rtc.c b/arch/arm/mach-imx/devices/platform-mxc_rtc.c
deleted file mode 100644
index 0c746de1dd1d..000000000000
--- a/arch/arm/mach-imx/devices/platform-mxc_rtc.c
+++ /dev/null
@@ -1,43 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010-2011 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_rtc_data_entry_single(soc, _devid)			\
-	{								\
-		.devid = _devid,					\
-		.iobase = soc ## _RTC_BASE_ADDR,			\
-		.irq = soc ## _INT_RTC,					\
-	}
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_rtc_data imx31_mxc_rtc_data __initconst =
-	imx_mxc_rtc_data_entry_single(MX31, "imx21-rtc");
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_rtc_data imx35_mxc_rtc_data __initconst =
-	imx_mxc_rtc_data_entry_single(MX35, "imx21-rtc");
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_rtc(
-		const struct imx_mxc_rtc_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_16K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device(data->devid, -1,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-mxc_w1.c b/arch/arm/mach-imx/devices/platform-mxc_w1.c
deleted file mode 100644
index ab42c6b0542c..000000000000
--- a/arch/arm/mach-imx/devices/platform-mxc_w1.c
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_mxc_w1_data_entry_single(soc)				\
-	{								\
-		.iobase = soc ## _OWIRE_BASE_ADDR,			\
-	}
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_mxc_w1_data imx21_mxc_w1_data __initconst =
-	imx_mxc_w1_data_entry_single(MX21);
-#endif /* ifdef CONFIG_SOC_IMX21 */
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_mxc_w1_data imx27_mxc_w1_data __initconst =
-	imx_mxc_w1_data_entry_single(MX27);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_mxc_w1_data imx31_mxc_w1_data __initconst =
-	imx_mxc_w1_data_entry_single(MX31);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_mxc_w1_data imx35_mxc_w1_data __initconst =
-	imx_mxc_w1_data_entry_single(MX35);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_mxc_w1(
-		const struct imx_mxc_w1_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_4K - 1,
-			.flags = IORESOURCE_MEM,
-		},
-	};
-
-	return imx_add_platform_device("mxc_w1", 0,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-pata_imx.c b/arch/arm/mach-imx/devices/platform-pata_imx.c
deleted file mode 100644
index 0e985fffba78..000000000000
--- a/arch/arm/mach-imx/devices/platform-pata_imx.c
+++ /dev/null
@@ -1,45 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_pata_imx_data_entry_single(soc, _size)			\
-	{								\
-		.iobase = soc ## _ATA_BASE_ADDR,			\
-		.iosize = _size,					\
-		.irq = soc ## _INT_ATA,					\
-	}
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_pata_imx_data imx27_pata_imx_data __initconst =
-	imx_pata_imx_data_entry_single(MX27, SZ_4K);
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_pata_imx_data imx31_pata_imx_data __initconst =
-	imx_pata_imx_data_entry_single(MX31, SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_pata_imx_data imx35_pata_imx_data __initconst =
-	imx_pata_imx_data_entry_single(MX35, SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_pata_imx(
-		const struct imx_pata_imx_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		},
-		{
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	return imx_add_platform_device("pata_imx", -1,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
-
diff --git a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c
deleted file mode 100644
index 40c261071144..000000000000
--- a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c
+++ /dev/null
@@ -1,64 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2010 Pengutronix, Wolfram Sang <kernel@pengutronix.de>
- */
-
-#include <linux/platform_data/mmc-esdhc-imx.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_sdhci_esdhc_imx_data_entry_single(soc, _devid, _id, hwid) \
-	{								\
-		.devid = _devid,					\
-		.id = _id,						\
-		.iobase = soc ## _ESDHC ## hwid ## _BASE_ADDR,	\
-		.irq = soc ## _INT_ESDHC ## hwid,			\
-	}
-
-#define imx_sdhci_esdhc_imx_data_entry(soc, devid, id, hwid)	\
-	[id] = imx_sdhci_esdhc_imx_data_entry_single(soc, devid, id, hwid)
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_sdhci_esdhc_imx_data
-imx35_sdhci_esdhc_imx_data[] __initconst = {
-#define imx35_sdhci_esdhc_imx_data_entry(_id, _hwid)			\
-	imx_sdhci_esdhc_imx_data_entry(MX35, "sdhci-esdhc-imx35", _id, _hwid)
-	imx35_sdhci_esdhc_imx_data_entry(0, 1),
-	imx35_sdhci_esdhc_imx_data_entry(1, 2),
-	imx35_sdhci_esdhc_imx_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-static const struct esdhc_platform_data default_esdhc_pdata __initconst = {
-	.wp_type = ESDHC_WP_NONE,
-	.cd_type = ESDHC_CD_NONE,
-};
-
-struct platform_device *__init imx_add_sdhci_esdhc_imx(
-		const struct imx_sdhci_esdhc_imx_data *data,
-		const struct esdhc_platform_data *pdata)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_16K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	/*
-	 * If machine does not provide pdata, use the default one
-	 * which means no WP/CD support
-	 */
-	if (!pdata)
-		pdata = &default_esdhc_pdata;
-
-	return imx_add_platform_device_dmamask(data->devid, data->id, res,
-			ARRAY_SIZE(res), pdata, sizeof(*pdata),
-			DMA_BIT_MASK(32));
-}
diff --git a/arch/arm/mach-imx/devices/platform-spi_imx.c b/arch/arm/mach-imx/devices/platform-spi_imx.c
deleted file mode 100644
index 27747bf628a3..000000000000
--- a/arch/arm/mach-imx/devices/platform-spi_imx.c
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009-2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- */
-#include <linux/gpio/machine.h>
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_spi_imx_data_entry_single(soc, type, _devid, _id, hwid, _size) \
-	{								\
-		.devid = _devid,					\
-		.id = _id,						\
-		.iobase = soc ## _ ## type ## hwid ## _BASE_ADDR,	\
-		.iosize = _size,					\
-		.irq = soc ## _INT_ ## type ## hwid,			\
-	}
-
-#define imx_spi_imx_data_entry(soc, type, devid, id, hwid, size)	\
-	[id] = imx_spi_imx_data_entry_single(soc, type, devid, id, hwid, size)
-
-#ifdef CONFIG_SOC_IMX21
-const struct imx_spi_imx_data imx21_cspi_data[] __initconst = {
-#define imx21_cspi_data_entry(_id, _hwid)                            \
-	imx_spi_imx_data_entry(MX21, CSPI, "imx21-cspi", _id, _hwid, SZ_4K)
-	imx21_cspi_data_entry(0, 1),
-	imx21_cspi_data_entry(1, 2),
-};
-#endif
-
-#ifdef CONFIG_SOC_IMX27
-const struct imx_spi_imx_data imx27_cspi_data[] __initconst = {
-#define imx27_cspi_data_entry(_id, _hwid)				\
-	imx_spi_imx_data_entry(MX27, CSPI, "imx27-cspi", _id, _hwid, SZ_4K)
-	imx27_cspi_data_entry(0, 1),
-	imx27_cspi_data_entry(1, 2),
-	imx27_cspi_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX27 */
-
-#ifdef CONFIG_SOC_IMX31
-const struct imx_spi_imx_data imx31_cspi_data[] __initconst = {
-#define imx31_cspi_data_entry(_id, _hwid)				\
-	imx_spi_imx_data_entry(MX31, CSPI, "imx31-cspi", _id, _hwid, SZ_4K)
-	imx31_cspi_data_entry(0, 1),
-	imx31_cspi_data_entry(1, 2),
-	imx31_cspi_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX31 */
-
-#ifdef CONFIG_SOC_IMX35
-const struct imx_spi_imx_data imx35_cspi_data[] __initconst = {
-#define imx35_cspi_data_entry(_id, _hwid)                           \
-	imx_spi_imx_data_entry(MX35, CSPI, "imx35-cspi", _id, _hwid, SZ_4K)
-	imx35_cspi_data_entry(0, 1),
-	imx35_cspi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX35 */
-
-struct platform_device *__init imx_add_spi_imx(
-	const struct imx_spi_imx_data *data, struct gpiod_lookup_table *gtable)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + data->iosize - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-	if (gtable)
-		gpiod_add_lookup_table(gtable);
-	return imx_add_platform_device(data->devid, data->id,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/ehci-imx27.c b/arch/arm/mach-imx/ehci-imx27.c
deleted file mode 100644
index 83962ce75983..000000000000
--- a/arch/arm/mach-imx/ehci-imx27.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET	0x600
-
-#define MX27_OTG_SIC_SHIFT	29
-#define MX27_OTG_SIC_MASK	(0x3 << MX27_OTG_SIC_SHIFT)
-#define MX27_OTG_PM_BIT		(1 << 24)
-
-#define MX27_H2_SIC_SHIFT	21
-#define MX27_H2_SIC_MASK	(0x3 << MX27_H2_SIC_SHIFT)
-#define MX27_H2_PM_BIT		(1 << 16)
-#define MX27_H2_DT_BIT		(1 << 5)
-
-#define MX27_H1_SIC_SHIFT	13
-#define MX27_H1_SIC_MASK	(0x3 << MX27_H1_SIC_SHIFT)
-#define MX27_H1_PM_BIT		(1 << 8)
-#define MX27_H1_DT_BIT		(1 << 4)
-
-int mx27_initialize_usb_hw(int port, unsigned int flags)
-{
-	unsigned int v;
-
-	v = readl(MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	switch (port) {
-	case 0:	/* OTG port */
-		v &= ~(MX27_OTG_SIC_MASK | MX27_OTG_PM_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_OTG_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX27_OTG_PM_BIT;
-		break;
-	case 1: /* H1 port */
-		v &= ~(MX27_H1_SIC_MASK | MX27_H1_PM_BIT | MX27_H1_DT_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H1_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX27_H1_PM_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX27_H1_DT_BIT;
-
-		break;
-	case 2:	/* H2 port */
-		v &= ~(MX27_H2_SIC_MASK | MX27_H2_PM_BIT | MX27_H2_DT_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H2_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX27_H2_PM_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX27_H2_DT_BIT;
-
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	writel(v, MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	return 0;
-}
-
diff --git a/arch/arm/mach-imx/ehci-imx31.c b/arch/arm/mach-imx/ehci-imx31.c
deleted file mode 100644
index d6d794d53a63..000000000000
--- a/arch/arm/mach-imx/ehci-imx31.c
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET	0x600
-
-#define MX31_OTG_SIC_SHIFT	29
-#define MX31_OTG_SIC_MASK	(0x3 << MX31_OTG_SIC_SHIFT)
-#define MX31_OTG_PM_BIT		(1 << 24)
-
-#define MX31_H2_SIC_SHIFT	21
-#define MX31_H2_SIC_MASK	(0x3 << MX31_H2_SIC_SHIFT)
-#define MX31_H2_PM_BIT		(1 << 16)
-#define MX31_H2_DT_BIT		(1 << 5)
-
-#define MX31_H1_SIC_SHIFT	13
-#define MX31_H1_SIC_MASK	(0x3 << MX31_H1_SIC_SHIFT)
-#define MX31_H1_PM_BIT		(1 << 8)
-#define MX31_H1_DT_BIT		(1 << 4)
-
-int mx31_initialize_usb_hw(int port, unsigned int flags)
-{
-	unsigned int v;
-
-	v = readl(MX31_IO_ADDRESS(MX31_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	switch (port) {
-	case 0:	/* OTG port */
-		v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_OTG_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX31_OTG_PM_BIT;
-
-		break;
-	case 1: /* H1 port */
-		v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H1_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX31_H1_PM_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX31_H1_DT_BIT;
-
-		break;
-	case 2:	/* H2 port */
-		v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H2_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX31_H2_PM_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX31_H2_DT_BIT;
-
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	writel(v, MX31_IO_ADDRESS(MX31_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	return 0;
-}
diff --git a/arch/arm/mach-imx/ehci-imx35.c b/arch/arm/mach-imx/ehci-imx35.c
deleted file mode 100644
index e6ba965c5c5b..000000000000
--- a/arch/arm/mach-imx/ehci-imx35.c
+++ /dev/null
@@ -1,89 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET	0x600
-
-#define MX35_OTG_SIC_SHIFT	29
-#define MX35_OTG_SIC_MASK	(0x3 << MX35_OTG_SIC_SHIFT)
-#define MX35_OTG_PM_BIT		(1 << 24)
-#define MX35_OTG_PP_BIT		(1 << 11)
-#define MX35_OTG_OCPOL_BIT	(1 << 3)
-
-#define MX35_H1_SIC_SHIFT	21
-#define MX35_H1_SIC_MASK	(0x3 << MX35_H1_SIC_SHIFT)
-#define MX35_H1_PP_BIT		(1 << 18)
-#define MX35_H1_PM_BIT		(1 << 16)
-#define MX35_H1_IPPUE_UP_BIT	(1 << 7)
-#define MX35_H1_IPPUE_DOWN_BIT	(1 << 6)
-#define MX35_H1_TLL_BIT		(1 << 5)
-#define MX35_H1_USBTE_BIT	(1 << 4)
-#define MX35_H1_OCPOL_BIT	(1 << 2)
-
-int mx35_initialize_usb_hw(int port, unsigned int flags)
-{
-	unsigned int v;
-
-	v = readl(MX35_IO_ADDRESS(MX35_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	switch (port) {
-	case 0:	/* OTG port */
-		v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT |
-			MX35_OTG_OCPOL_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX35_OTG_PM_BIT;
-
-		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
-			v |= MX35_OTG_PP_BIT;
-
-		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
-			v |= MX35_OTG_OCPOL_BIT;
-
-		break;
-	case 1: /* H1 port */
-		v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT |
-			MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
-			MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX35_H1_PM_BIT;
-
-		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
-			v |= MX35_H1_PP_BIT;
-
-		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
-			v |= MX35_H1_OCPOL_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX35_H1_TLL_BIT;
-
-		if (flags & MXC_EHCI_INTERNAL_PHY)
-			v |= MX35_H1_USBTE_BIT;
-
-		if (flags & MXC_EHCI_IPPUE_DOWN)
-			v |= MX35_H1_IPPUE_DOWN_BIT;
-
-		if (flags & MXC_EHCI_IPPUE_UP)
-			v |= MX35_H1_IPPUE_UP_BIT;
-
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	writel(v, MX35_IO_ADDRESS(MX35_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	return 0;
-}
diff --git a/arch/arm/mach-imx/ehci.h b/arch/arm/mach-imx/ehci.h
deleted file mode 100644
index b7ad6175f5bf..000000000000
--- a/arch/arm/mach-imx/ehci.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __MACH_IMX_EHCI_H
-#define __MACH_IMX_EHCI_H
-
-/* values for portsc field */
-#define MXC_EHCI_PHY_LOW_POWER_SUSPEND	(1 << 23)
-#define MXC_EHCI_FORCE_FS		(1 << 24)
-#define MXC_EHCI_UTMI_8BIT		(0 << 28)
-#define MXC_EHCI_UTMI_16BIT		(1 << 28)
-#define MXC_EHCI_SERIAL			(1 << 29)
-#define MXC_EHCI_MODE_UTMI		(0 << 30)
-#define MXC_EHCI_MODE_PHILIPS		(1 << 30)
-#define MXC_EHCI_MODE_ULPI		(2 << 30)
-#define MXC_EHCI_MODE_SERIAL		(3 << 30)
-
-/* values for flags field */
-#define MXC_EHCI_INTERFACE_DIFF_UNI	(0 << 0)
-#define MXC_EHCI_INTERFACE_DIFF_BI	(1 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_UNI	(2 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_BI	(3 << 0)
-#define MXC_EHCI_INTERFACE_MASK		(0xf)
-
-#define MXC_EHCI_POWER_PINS_ENABLED	(1 << 5)
-#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH	(1 << 6)
-#define MXC_EHCI_OC_PIN_ACTIVE_LOW	(1 << 7)
-#define MXC_EHCI_TTL_ENABLED		(1 << 8)
-
-#define MXC_EHCI_INTERNAL_PHY		(1 << 9)
-#define MXC_EHCI_IPPUE_DOWN		(1 << 10)
-#define MXC_EHCI_IPPUE_UP		(1 << 11)
-#define MXC_EHCI_WAKEUP_ENABLED		(1 << 12)
-#define MXC_EHCI_ITC_NO_THRESHOLD	(1 << 13)
-
-#define MXC_USBCTRL_OFFSET		0
-#define MXC_USB_PHY_CTR_FUNC_OFFSET	0x8
-#define MXC_USB_PHY_CTR_FUNC2_OFFSET	0xc
-#define MXC_USBH2CTRL_OFFSET		0x14
-
-int mx25_initialize_usb_hw(int port, unsigned int flags);
-int mx31_initialize_usb_hw(int port, unsigned int flags);
-int mx35_initialize_usb_hw(int port, unsigned int flags);
-int mx27_initialize_usb_hw(int port, unsigned int flags);
-
-#endif /* __MACH_IMX_EHCI_H */
diff --git a/arch/arm/mach-imx/hardware.h b/arch/arm/mach-imx/hardware.h
index 92c5a9c9f94b..7acf7ce467ed 100644
--- a/arch/arm/mach-imx/hardware.h
+++ b/arch/arm/mach-imx/hardware.h
@@ -97,7 +97,6 @@
 #include "mx31.h"
 #include "mx35.h"
 #include "mx2x.h"
-#include "mx21.h"
 #include "mx27.h"
 
 #define imx_map_entry(soc, name, _type)	{				\
diff --git a/arch/arm/mach-imx/imx27-dt.c b/arch/arm/mach-imx/imx27-dt.c
deleted file mode 100644
index 29d97bd64381..000000000000
--- a/arch/arm/mach-imx/imx27-dt.c
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer, Pengutronix
- */
-
-#include <linux/irq.h>
-#include <linux/of_irq.h>
-#include <linux/of_platform.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "mx27.h"
-
-static const char * const imx27_dt_board_compat[] __initconst = {
-	"fsl,imx27",
-	NULL
-};
-
-DT_MACHINE_START(IMX27_DT, "Freescale i.MX27 (Device Tree Support)")
-	.map_io		= mx27_map_io,
-	.init_early	= imx27_init_early,
-	.init_irq	= mx27_init_irq,
-	.init_late	= imx27_pm_init,
-	.dt_compat	= imx27_dt_board_compat,
-MACHINE_END
diff --git a/arch/arm/mach-imx/iomux-imx31.c b/arch/arm/mach-imx/iomux-imx31.c
deleted file mode 100644
index abfc306655c8..000000000000
--- a/arch/arm/mach-imx/iomux-imx31.c
+++ /dev/null
@@ -1,161 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Valentin Longchamp <valentin.longchamp@epfl.ch>
- */
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * IOMUX register (base) addresses
- */
-#define IOMUX_BASE	MX31_IO_ADDRESS(MX31_IOMUXC_BASE_ADDR)
-#define IOMUXINT_OBS1	(IOMUX_BASE + 0x000)
-#define IOMUXINT_OBS2	(IOMUX_BASE + 0x004)
-#define IOMUXGPR	(IOMUX_BASE + 0x008)
-#define IOMUXSW_MUX_CTL	(IOMUX_BASE + 0x00C)
-#define IOMUXSW_PAD_CTL	(IOMUX_BASE + 0x154)
-
-static DEFINE_SPINLOCK(gpio_mux_lock);
-
-#define IOMUX_REG_MASK (IOMUX_PADNUM_MASK & ~0x3)
-
-static DECLARE_BITMAP(mxc_pin_alloc_map, NB_PORTS * 32);
-/*
- * set the mode for a IOMUX pin.
- */
-void mxc_iomux_mode(unsigned int pin_mode)
-{
-	u32 field;
-	u32 l;
-	u32 mode;
-	void __iomem *reg;
-
-	reg = IOMUXSW_MUX_CTL + (pin_mode & IOMUX_REG_MASK);
-	field = pin_mode & 0x3;
-	mode = (pin_mode & IOMUX_MODE_MASK) >> IOMUX_MODE_SHIFT;
-
-	spin_lock(&gpio_mux_lock);
-
-	l = imx_readl(reg);
-	l &= ~(0xff << (field * 8));
-	l |= mode << (field * 8);
-	imx_writel(l, reg);
-
-	spin_unlock(&gpio_mux_lock);
-}
-
-/*
- * This function configures the pad value for a IOMUX pin.
- */
-void mxc_iomux_set_pad(enum iomux_pins pin, u32 config)
-{
-	u32 field, l;
-	void __iomem *reg;
-
-	pin &= IOMUX_PADNUM_MASK;
-	reg = IOMUXSW_PAD_CTL + (pin + 2) / 3 * 4;
-	field = (pin + 2) % 3;
-
-	pr_debug("%s: reg offset = 0x%x, field = %d\n",
-			__func__, (pin + 2) / 3, field);
-
-	spin_lock(&gpio_mux_lock);
-
-	l = imx_readl(reg);
-	l &= ~(0x1ff << (field * 10));
-	l |= config << (field * 10);
-	imx_writel(l, reg);
-
-	spin_unlock(&gpio_mux_lock);
-}
-
-/*
- * allocs a single pin:
- * 	- reserves the pin so that it is not claimed by another driver
- * 	- setups the iomux according to the configuration
- */
-int mxc_iomux_alloc_pin(unsigned int pin, const char *label)
-{
-	unsigned pad = pin & IOMUX_PADNUM_MASK;
-
-	if (pad >= (PIN_MAX + 1)) {
-		printk(KERN_ERR "mxc_iomux: Attempt to request nonexistent pin %u for \"%s\"\n",
-			pad, label ? label : "?");
-		return -EINVAL;
-	}
-
-	if (test_and_set_bit(pad, mxc_pin_alloc_map)) {
-		printk(KERN_ERR "mxc_iomux: pin %u already used. Allocation for \"%s\" failed\n",
-			pad, label ? label : "?");
-		return -EBUSY;
-	}
-	mxc_iomux_mode(pin);
-
-	return 0;
-}
-
-int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
-		const char *label)
-{
-	const unsigned int *p = pin_list;
-	int i;
-	int ret = -EINVAL;
-
-	for (i = 0; i < count; i++) {
-		ret = mxc_iomux_alloc_pin(*p, label);
-		if (ret)
-			goto setup_error;
-		p++;
-	}
-	return 0;
-
-setup_error:
-	mxc_iomux_release_multiple_pins(pin_list, i);
-	return ret;
-}
-
-void mxc_iomux_release_pin(unsigned int pin)
-{
-	unsigned pad = pin & IOMUX_PADNUM_MASK;
-
-	if (pad < (PIN_MAX + 1))
-		clear_bit(pad, mxc_pin_alloc_map);
-}
-
-void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count)
-{
-	const unsigned int *p = pin_list;
-	int i;
-
-	for (i = 0; i < count; i++) {
-		mxc_iomux_release_pin(*p);
-		p++;
-	}
-}
-
-/*
- * This function enables/disables the general purpose function for a particular
- * signal.
- */
-void mxc_iomux_set_gpr(enum iomux_gp_func gp, bool en)
-{
-	u32 l;
-
-	spin_lock(&gpio_mux_lock);
-	l = imx_readl(IOMUXGPR);
-	if (en)
-		l |= gp;
-	else
-		l &= ~gp;
-
-	imx_writel(l, IOMUXGPR);
-	spin_unlock(&gpio_mux_lock);
-}
diff --git a/arch/arm/mach-imx/iomux-mx21.h b/arch/arm/mach-imx/iomux-mx21.h
deleted file mode 100644
index 6eab3478fb80..000000000000
--- a/arch/arm/mach-imx/iomux-mx21.h
+++ /dev/null
@@ -1,109 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX21_H__
-#define __MACH_IOMUX_MX21_H__
-
-#include "iomux-mx2x.h"
-#include "iomux-v1.h"
-
-/* Primary GPIO pin functions */
-
-#define PB22_PF_USBH1_BYP	(GPIO_PORTB | GPIO_PF | 22)
-#define PB25_PF_USBH1_ON	(GPIO_PORTB | GPIO_PF | 25)
-#define PC5_PF_USBOTG_SDA	(GPIO_PORTC | GPIO_PF | 5)
-#define PC6_PF_USBOTG_SCL	(GPIO_PORTC | GPIO_PF | 6)
-#define PC7_PF_USBOTG_ON	(GPIO_PORTC | GPIO_PF | 7)
-#define PC8_PF_USBOTG_FS	(GPIO_PORTC | GPIO_PF | 8)
-#define PC9_PF_USBOTG_OE	(GPIO_PORTC | GPIO_PF | 9)
-#define PC10_PF_USBOTG_TXDM	(GPIO_PORTC | GPIO_PF | 10)
-#define PC11_PF_USBOTG_TXDP	(GPIO_PORTC | GPIO_PF | 11)
-#define PC12_PF_USBOTG_RXDM	(GPIO_PORTC | GPIO_PF | 12)
-#define PC13_PF_USBOTG_RXDP	(GPIO_PORTC | GPIO_PF | 13)
-#define PC16_PF_SAP_FS		(GPIO_PORTC | GPIO_PF | 16)
-#define PC17_PF_SAP_RXD		(GPIO_PORTC | GPIO_PF | 17)
-#define PC18_PF_SAP_TXD		(GPIO_PORTC | GPIO_PF | 18)
-#define PC19_PF_SAP_CLK		(GPIO_PORTC | GPIO_PF | 19)
-#define PE0_PF_TEST_WB2		(GPIO_PORTE | GPIO_PF | 0)
-#define PE1_PF_TEST_WB1		(GPIO_PORTE | GPIO_PF | 1)
-#define PE2_PF_TEST_WB0		(GPIO_PORTE | GPIO_PF | 2)
-#define PF1_PF_NFCE		(GPIO_PORTF | GPIO_PF | 1)
-#define PF3_PF_NFCLE		(GPIO_PORTF | GPIO_PF | 3)
-#define PF7_PF_NFIO0		(GPIO_PORTF | GPIO_PF | 7)
-#define PF8_PF_NFIO1		(GPIO_PORTF | GPIO_PF | 8)
-#define PF9_PF_NFIO2		(GPIO_PORTF | GPIO_PF | 9)
-#define PF10_PF_NFIO3		(GPIO_PORTF | GPIO_PF | 10)
-#define PF11_PF_NFIO4		(GPIO_PORTF | GPIO_PF | 11)
-#define PF12_PF_NFIO5		(GPIO_PORTF | GPIO_PF | 12)
-#define PF13_PF_NFIO6		(GPIO_PORTF | GPIO_PF | 13)
-#define PF14_PF_NFIO7		(GPIO_PORTF | GPIO_PF | 14)
-#define PF16_PF_RES		(GPIO_PORTF | GPIO_PF | 16)
-
-/* Alternate GPIO pin functions */
-
-#define PA5_AF_BMI_CLK_CS	(GPIO_PORTA | GPIO_AF | 5)
-#define PA6_AF_BMI_D0		(GPIO_PORTA | GPIO_AF | 6)
-#define PA7_AF_BMI_D1		(GPIO_PORTA | GPIO_AF | 7)
-#define PA8_AF_BMI_D2		(GPIO_PORTA | GPIO_AF | 8)
-#define PA9_AF_BMI_D3		(GPIO_PORTA | GPIO_AF | 9)
-#define PA10_AF_BMI_D4		(GPIO_PORTA | GPIO_AF | 10)
-#define PA11_AF_BMI_D5		(GPIO_PORTA | GPIO_AF | 11)
-#define PA12_AF_BMI_D6		(GPIO_PORTA | GPIO_AF | 12)
-#define PA13_AF_BMI_D7		(GPIO_PORTA | GPIO_AF | 13)
-#define PA14_AF_BMI_D8		(GPIO_PORTA | GPIO_AF | 14)
-#define PA15_AF_BMI_D9		(GPIO_PORTA | GPIO_AF | 15)
-#define PA16_AF_BMI_D10		(GPIO_PORTA | GPIO_AF | 16)
-#define PA17_AF_BMI_D11		(GPIO_PORTA | GPIO_AF | 17)
-#define PA18_AF_BMI_D12		(GPIO_PORTA | GPIO_AF | 18)
-#define PA19_AF_BMI_D13		(GPIO_PORTA | GPIO_AF | 19)
-#define PA20_AF_BMI_D14		(GPIO_PORTA | GPIO_AF | 20)
-#define PA21_AF_BMI_D15		(GPIO_PORTA | GPIO_AF | 21)
-#define PA22_AF_BMI_READ_REQ	(GPIO_PORTA | GPIO_AF | 22)
-#define PA23_AF_BMI_WRITE	(GPIO_PORTA | GPIO_AF | 23)
-#define PA29_AF_BMI_RX_FULL	(GPIO_PORTA | GPIO_AF | 29)
-#define PA30_AF_BMI_READ	(GPIO_PORTA | GPIO_AF | 30)
-
-/* AIN GPIO pin functions */
-
-#define PC14_AIN_SYS_CLK	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 14)
-#define PD21_AIN_USBH2_FS	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 21)
-#define PD22_AIN_USBH2_OE	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 22)
-#define PD23_AIN_USBH2_TXDM	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 23)
-#define PD24_AIN_USBH2_TXDP	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 24)
-#define PE8_AIN_IR_TXD		(GPIO_PORTE | GPIO_AIN | GPIO_OUT | 8)
-#define PF0_AIN_PC_RST		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 0)
-#define PF1_AIN_PC_CE1		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 1)
-#define PF2_AIN_PC_CE2		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 2)
-#define PF3_AIN_PC_POE		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 3)
-#define PF4_AIN_PC_OE		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 4)
-#define PF5_AIN_PC_RW		(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 5)
-
-/* BIN GPIO pin functions */
-
-#define PC14_BIN_SYS_CLK	(GPIO_PORTC | GPIO_BIN | GPIO_OUT | 14)
-#define PD27_BIN_EXT_DMA_GRANT	(GPIO_PORTD | GPIO_BIN | GPIO_OUT | 27)
-
-/* CIN GPIO pin functions */
-
-#define PB26_CIN_USBH1_RXDAT	(GPIO_PORTB | GPIO_CIN | GPIO_OUT | 26)
-
-/* AOUT GPIO pin functions */
-
-#define PA29_AOUT_BMI_WAIT	(GPIO_PORTA | GPIO_AOUT | GPIO_IN | 29)
-#define PD19_AOUT_USBH2_RXDM	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 19)
-#define PD20_AOUT_USBH2_RXDP	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 20)
-#define PD25_AOUT_EXT_DMAREQ	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 25)
-#define PD26_AOUT_USBOTG_RXDAT	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 26)
-#define PE9_AOUT_IR_RXD		(GPIO_PORTE | GPIO_AOUT | GPIO_IN | 9)
-#define PF6_AOUT_PC_BVD2	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 6)
-#define PF7_AOUT_PC_BVD1	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 7)
-#define PF8_AOUT_PC_VS2		(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 8)
-#define PF9_AOUT_PC_VS1		(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 9)
-#define PF10_AOUT_PC_WP		(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 10)
-#define PF11_AOUT_PC_READY	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 11)
-#define PF12_AOUT_PC_WAIT	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 12)
-#define PF13_AOUT_PC_CD2	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 13)
-#define PF14_AOUT_PC_CD1	(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 14)
-
-#endif /* ifndef __MACH_IOMUX_MX21_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx27.h b/arch/arm/mach-imx/iomux-mx27.h
deleted file mode 100644
index 4d848d1ef1e3..000000000000
--- a/arch/arm/mach-imx/iomux-mx27.h
+++ /dev/null
@@ -1,192 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX27_H__
-#define __MACH_IOMUX_MX27_H__
-
-#include "iomux-mx2x.h"
-#include "iomux-v1.h"
-
-/* Primary GPIO pin functions */
-
-#define PA0_PF_USBH2_CLK	(GPIO_PORTA | GPIO_PF | 0)
-#define PA1_PF_USBH2_DIR	(GPIO_PORTA | GPIO_PF | 1)
-#define PA2_PF_USBH2_DATA7	(GPIO_PORTA | GPIO_PF | 2)
-#define PA3_PF_USBH2_NXT	(GPIO_PORTA | GPIO_PF | 3)
-#define PA4_PF_USBH2_STP	(GPIO_PORTA | GPIO_PF | 4)
-#define PB22_PF_USBH1_SUSP	(GPIO_PORTB | GPIO_PF | 22)
-#define PB25_PF_USBH1_RCV	(GPIO_PORTB | GPIO_PF | 25)
-#define PC5_PF_I2C2_SDA		(GPIO_PORTC | GPIO_PF | GPIO_IN | 5)
-#define PC6_PF_I2C2_SCL		(GPIO_PORTC | GPIO_PF | GPIO_IN | 6)
-#define PC7_PF_USBOTG_DATA5	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 7)
-#define PC8_PF_USBOTG_DATA6	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 8)
-#define PC9_PF_USBOTG_DATA0	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 9)
-#define PC10_PF_USBOTG_DATA2	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 10)
-#define PC11_PF_USBOTG_DATA1	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 11)
-#define PC12_PF_USBOTG_DATA4	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 12)
-#define PC13_PF_USBOTG_DATA3	(GPIO_PORTC | GPIO_PF | GPIO_OUT | 13)
-#define PC16_PF_SSI4_FS		(GPIO_PORTC | GPIO_PF | GPIO_IN | 16)
-#define PC17_PF_SSI4_RXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 17)
-#define PC18_PF_SSI4_TXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 18)
-#define PC19_PF_SSI4_CLK	(GPIO_PORTC | GPIO_PF | GPIO_IN | 19)
-#define PD0_PF_SD3_CMD		(GPIO_PORTD | GPIO_PF | 0)
-#define PD1_PF_SD3_CLK		(GPIO_PORTD | GPIO_PF | 1)
-#define PD2_PF_ATA_DATA0	(GPIO_PORTD | GPIO_PF | 2)
-#define PD3_PF_ATA_DATA1	(GPIO_PORTD | GPIO_PF | 3)
-#define PD4_PF_ATA_DATA2	(GPIO_PORTD | GPIO_PF | 4)
-#define PD5_PF_ATA_DATA3	(GPIO_PORTD | GPIO_PF | 5)
-#define PD6_PF_ATA_DATA4	(GPIO_PORTD | GPIO_PF | 6)
-#define PD7_PF_ATA_DATA5	(GPIO_PORTD | GPIO_PF | 7)
-#define PD8_PF_ATA_DATA6	(GPIO_PORTD | GPIO_PF | 8)
-#define PD9_PF_ATA_DATA7	(GPIO_PORTD | GPIO_PF | 9)
-#define PD10_PF_ATA_DATA8	(GPIO_PORTD | GPIO_PF | 10)
-#define PD11_PF_ATA_DATA9	(GPIO_PORTD | GPIO_PF | 11)
-#define PD12_PF_ATA_DATA10	(GPIO_PORTD | GPIO_PF | 12)
-#define PD13_PF_ATA_DATA11	(GPIO_PORTD | GPIO_PF | 13)
-#define PD14_PF_ATA_DATA12	(GPIO_PORTD | GPIO_PF | 14)
-#define PD15_PF_ATA_DATA13	(GPIO_PORTD | GPIO_PF | 15)
-#define PD16_PF_ATA_DATA14	(GPIO_PORTD | GPIO_PF | 16)
-#define PE0_PF_USBOTG_NXT	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 0)
-#define PE1_PF_USBOTG_STP	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 1)
-#define PE2_PF_USBOTG_DIR	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 2)
-#define PE24_PF_USBOTG_CLK	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 24)
-#define PE25_PF_USBOTG_DATA7	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 25)
-#define PF1_PF_NFCLE		(GPIO_PORTF | GPIO_PF | 1)
-#define PF3_PF_NFCE		(GPIO_PORTF | GPIO_PF | 3)
-#define PF7_PF_PC_POE		(GPIO_PORTF | GPIO_PF | 7)
-#define PF8_PF_PC_RW		(GPIO_PORTF | GPIO_PF | 8)
-#define PF9_PF_PC_IOIS16	(GPIO_PORTF | GPIO_PF | 9)
-#define PF10_PF_PC_RST		(GPIO_PORTF | GPIO_PF | 10)
-#define PF11_PF_PC_BVD2		(GPIO_PORTF | GPIO_PF | 11)
-#define PF12_PF_PC_BVD1		(GPIO_PORTF | GPIO_PF | 12)
-#define PF13_PF_PC_VS2		(GPIO_PORTF | GPIO_PF | 13)
-#define PF14_PF_PC_VS1		(GPIO_PORTF | GPIO_PF | 14)
-#define PF16_PF_PC_PWRON	(GPIO_PORTF | GPIO_PF | 16)
-#define PF17_PF_PC_READY	(GPIO_PORTF | GPIO_PF | 17)
-#define PF18_PF_PC_WAIT		(GPIO_PORTF | GPIO_PF | 18)
-#define PF19_PF_PC_CD2		(GPIO_PORTF | GPIO_PF | 19)
-#define PF20_PF_PC_CD1		(GPIO_PORTF | GPIO_PF | 20)
-#define PF23_PF_ATA_DATA15	(GPIO_PORTF | GPIO_PF | 23)
-
-/* Alternate GPIO pin functions */
-
-#define PB4_AF_MSHC_DATA0	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 4)
-#define PB5_AF_MSHC_DATA1	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 5)
-#define PB6_AF_MSHC_DATA2	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 6)
-#define PB7_AF_MSHC_DATA4	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 7)
-#define PB8_AF_MSHC_BS		(GPIO_PORTB | GPIO_AF | GPIO_OUT | 8)
-#define PB9_AF_MSHC_SCLK	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 9)
-#define PB10_AF_UART6_TXD	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 10)
-#define PB11_AF_UART6_RXD	(GPIO_PORTB | GPIO_AF | GPIO_IN | 11)
-#define PB12_AF_UART6_CTS	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 12)
-#define PB13_AF_UART6_RTS	(GPIO_PORTB | GPIO_AF | GPIO_IN | 13)
-#define PB18_AF_UART5_TXD	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 18)
-#define PB19_AF_UART5_RXD	(GPIO_PORTB | GPIO_AF | GPIO_IN | 19)
-#define PB20_AF_UART5_CTS	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 20)
-#define PB21_AF_UART5_RTS	(GPIO_PORTB | GPIO_AF | GPIO_IN | 21)
-#define PC8_AF_FEC_MDIO		(GPIO_PORTC | GPIO_AF | GPIO_IN | 8)
-#define PC24_AF_GPT5_TOUT	(GPIO_PORTC | GPIO_AF | 24)
-#define PC25_AF_GPT5_TIN	(GPIO_PORTC | GPIO_AF | 25)
-#define PC26_AF_GPT4_TOUT	(GPIO_PORTC | GPIO_AF | 26)
-#define PC27_AF_GPT4_TIN	(GPIO_PORTC | GPIO_AF | 27)
-#define PD1_AF_ETMTRACE_PKT15	(GPIO_PORTD | GPIO_AF | 1)
-#define PD6_AF_ETMTRACE_PKT14	(GPIO_PORTD | GPIO_AF | 6)
-#define PD7_AF_ETMTRACE_PKT13	(GPIO_PORTD | GPIO_AF | 7)
-#define PD9_AF_ETMTRACE_PKT12	(GPIO_PORTD | GPIO_AF | 9)
-#define PD2_AF_SD3_D0		(GPIO_PORTD | GPIO_AF | 2)
-#define PD3_AF_SD3_D1		(GPIO_PORTD | GPIO_AF | 3)
-#define PD4_AF_SD3_D2		(GPIO_PORTD | GPIO_AF | 4)
-#define PD5_AF_SD3_D3		(GPIO_PORTD | GPIO_AF | 5)
-#define PD8_AF_FEC_MDIO		(GPIO_PORTD | GPIO_AF | GPIO_IN | 8)
-#define PD10_AF_ETMTRACE_PKT11	(GPIO_PORTD | GPIO_AF | 10)
-#define PD11_AF_ETMTRACE_PKT10	(GPIO_PORTD | GPIO_AF | 11)
-#define PD12_AF_ETMTRACE_PKT9	(GPIO_PORTD | GPIO_AF | 12)
-#define PD13_AF_ETMTRACE_PKT8	(GPIO_PORTD | GPIO_AF | 13)
-#define PD14_AF_ETMTRACE_PKT7	(GPIO_PORTD | GPIO_AF | 14)
-#define PD15_AF_ETMTRACE_PKT6	(GPIO_PORTD | GPIO_AF | 15)
-#define PD16_AF_ETMTRACE_PKT5	(GPIO_PORTD | GPIO_AF | 16)
-#define PF1_AF_ETMTRACE_PKT0	(GPIO_PORTF | GPIO_AF | 1)
-#define PF3_AF_ETMTRACE_PKT2	(GPIO_PORTF | GPIO_AF | 3)
-#define PF5_AF_ETMPIPESTAT11	(GPIO_PORTF | GPIO_AF | 5)
-#define PF7_AF_ATA_BUFFER_EN	(GPIO_PORTF | GPIO_AF | 7)
-#define PF8_AF_ATA_IORDY	(GPIO_PORTF | GPIO_AF | 8)
-#define PF9_AF_ATA_INTRQ	(GPIO_PORTF | GPIO_AF | 9)
-#define PF10_AF_ATA_RESET	(GPIO_PORTF | GPIO_AF | 10)
-#define PF11_AF_ATA_DMACK	(GPIO_PORTF | GPIO_AF | 11)
-#define PF12_AF_ATA_DMAREQ	(GPIO_PORTF | GPIO_AF | 12)
-#define PF13_AF_ATA_DA0		(GPIO_PORTF | GPIO_AF | 13)
-#define PF14_AF_ATA_DA1		(GPIO_PORTF | GPIO_AF | 14)
-#define PF15_AF_ETMTRACE_SYNC	(GPIO_PORTF | GPIO_AF | 15)
-#define PF16_AF_ATA_DA2		(GPIO_PORTF | GPIO_AF | 16)
-#define PF17_AF_ATA_CS0		(GPIO_PORTF | GPIO_AF | 17)
-#define PF18_AF_ATA_CS1		(GPIO_PORTF | GPIO_AF | 18)
-#define PF19_AF_ATA_DIOW	(GPIO_PORTF | GPIO_AF | 19)
-#define PF20_AF_ATA_DIOR	(GPIO_PORTF | GPIO_AF | 20)
-#define PF22_AF_ETMTRACE_CLK	(GPIO_PORTF | GPIO_AF | 22)
-#define PF23_AF_ETMTRACE_PKT4	(GPIO_PORTF | GPIO_AF | 23)
-
-/* AIN GPIO pin functions */
-
-#define PC14_AIN_SSI1_MCLK	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 14)
-#define PC15_AIN_GPT6_TOUT	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 15)
-#define PD0_AIN_FEC_TXD0	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 0)
-#define PD1_AIN_FEC_TXD1	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 1)
-#define PD2_AIN_FEC_TXD2	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 2)
-#define PD3_AIN_FEC_TXD3	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 3)
-#define PD9_AIN_FEC_MDC		(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 9)
-#define PD16_AIN_FEC_TX_ER	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 16)
-#define PD27_AIN_EXT_DMA_GRANT	(GPIO_PORTD | GPIO_AIN | GPIO_OUT | 27)
-#define PF23_AIN_FEC_TX_EN	(GPIO_PORTF | GPIO_AIN | GPIO_OUT | 23)
-
-/* BIN GPIO pin functions */
-
-#define PC14_BIN_SSI2_MCLK	(GPIO_PORTC | GPIO_BIN | GPIO_OUT | 14)
-
-/* CIN GPIO pin functions */
-
-#define PD2_CIN_SLCDC1_DAT0	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 2)
-#define PD3_CIN_SLCDC1_DAT1	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 3)
-#define PD4_CIN_SLCDC1_DAT2	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 4)
-#define PD5_CIN_SLCDC1_DAT3	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 5)
-#define PD6_CIN_SLCDC1_DAT4	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 6)
-#define PD7_CIN_SLCDC1_DAT5	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 7)
-#define PD8_CIN_SLCDC1_DAT6	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 8)
-#define PD9_CIN_SLCDC1_DAT7	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 9)
-#define PD10_CIN_SLCDC1_DAT8	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 10)
-#define PD11_CIN_SLCDC1_DAT9	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 11)
-#define PD12_CIN_SLCDC1_DAT10	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 12)
-#define PD13_CIN_SLCDC1_DAT11	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 13)
-#define PD14_CIN_SLCDC1_DAT12	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 14)
-#define PD15_CIN_SLCDC1_DAT13	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 15)
-#define PD16_CIN_SLCDC1_DAT14	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 16)
-#define PD23_CIN_SLCDC1_DAT15	(GPIO_PORTD | GPIO_CIN | GPIO_OUT | 23)
-#define PF27_CIN_EXT_DMA_GRANT	(GPIO_PORTF | GPIO_CIN | GPIO_OUT | 27)
-/* LCDC_TESTx on PBxx omitted, because it's not clear what they do */
-
-/* AOUT GPIO pin functions */
-
-#define PC14_AOUT_GPT6_TIN	(GPIO_PORTC | GPIO_AOUT | GPIO_IN | 14)
-#define PD4_AOUT_FEC_RX_ER	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 4)
-#define PD5_AOUT_FEC_RXD1	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 5)
-#define PD6_AOUT_FEC_RXD2	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 6)
-#define PD7_AOUT_FEC_RXD3	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 7)
-#define PD10_AOUT_FEC_CRS	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 10)
-#define PD11_AOUT_FEC_TX_CLK	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 11)
-#define PD12_AOUT_FEC_RXD0	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 12)
-#define PD13_AOUT_FEC_RX_DV	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 13)
-#define PD14_AOUT_FEC_RX_CLK	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 14)
-#define PD15_AOUT_FEC_COL	(GPIO_PORTD | GPIO_AOUT | GPIO_IN | 15)
-
-/* BOUT GPIO pin functions */
-
-#define PC17_BOUT_PC_IOIS16	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 17)
-#define PC18_BOUT_PC_BVD2	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 18)
-#define PC19_BOUT_PC_BVD1	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 19)
-#define PC28_BOUT_PC_BVD2	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 28)
-#define PC29_BOUT_PC_VS1	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 29)
-#define PC30_BOUT_PC_READY	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 30)
-#define PC31_BOUT_PC_WAIT	(GPIO_PORTC | GPIO_BOUT | GPIO_IN | 31)
-
-#endif /* __MACH_IOMUX_MX27_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx2x.h b/arch/arm/mach-imx/iomux-mx2x.h
deleted file mode 100644
index ce6b6d20a4f0..000000000000
--- a/arch/arm/mach-imx/iomux-mx2x.h
+++ /dev/null
@@ -1,217 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_MX2x_H__
-#define __MACH_IOMUX_MX2x_H__
-
-/* Primary GPIO pin functions */
-
-#define PA5_PF_LSCLK		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 5)
-#define PA6_PF_LD0		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 6)
-#define PA7_PF_LD1		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 7)
-#define PA8_PF_LD2		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 8)
-#define PA9_PF_LD3		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 9)
-#define PA10_PF_LD4		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 10)
-#define PA11_PF_LD5		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 11)
-#define PA12_PF_LD6		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 12)
-#define PA13_PF_LD7		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 13)
-#define PA14_PF_LD8		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 14)
-#define PA15_PF_LD9		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 15)
-#define PA16_PF_LD10		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 16)
-#define PA17_PF_LD11		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 17)
-#define PA18_PF_LD12		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 18)
-#define PA19_PF_LD13		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 19)
-#define PA20_PF_LD14		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 20)
-#define PA21_PF_LD15		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 21)
-#define PA22_PF_LD16		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 22)
-#define PA23_PF_LD17		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 23)
-#define PA24_PF_REV		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 24)
-#define PA25_PF_CLS		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 25)
-#define PA26_PF_PS		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 26)
-#define PA27_PF_SPL_SPR		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 27)
-#define PA28_PF_HSYNC		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 28)
-#define PA29_PF_VSYNC		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 29)
-#define PA30_PF_CONTRAST	(GPIO_PORTA | GPIO_PF | GPIO_OUT | 30)
-#define PA31_PF_OE_ACD		(GPIO_PORTA | GPIO_PF | GPIO_OUT | 31)
-#define PB4_PF_SD2_D0		(GPIO_PORTB | GPIO_PF | 4)
-#define PB5_PF_SD2_D1		(GPIO_PORTB | GPIO_PF | 5)
-#define PB6_PF_SD2_D2		(GPIO_PORTB | GPIO_PF | 6)
-#define PB7_PF_SD2_D3		(GPIO_PORTB | GPIO_PF | 7)
-#define PB8_PF_SD2_CMD		(GPIO_PORTB | GPIO_PF | 8)
-#define PB9_PF_SD2_CLK		(GPIO_PORTB | GPIO_PF | 9)
-#define PB10_PF_CSI_D0		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 10)
-#define PB11_PF_CSI_D1		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 11)
-#define PB12_PF_CSI_D2		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 12)
-#define PB13_PF_CSI_D3		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 13)
-#define PB14_PF_CSI_D4		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 14)
-#define PB15_PF_CSI_MCLK	(GPIO_PORTB | GPIO_PF | GPIO_OUT | 15)
-#define PB16_PF_CSI_PIXCLK	(GPIO_PORTB | GPIO_PF | GPIO_OUT | 16)
-#define PB17_PF_CSI_D5		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 17)
-#define PB18_PF_CSI_D6		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 18)
-#define PB19_PF_CSI_D7		(GPIO_PORTB | GPIO_PF | GPIO_OUT | 19)
-#define PB20_PF_CSI_VSYNC	(GPIO_PORTB | GPIO_PF | GPIO_OUT | 20)
-#define PB21_PF_CSI_HSYNC	(GPIO_PORTB | GPIO_PF | GPIO_OUT | 21)
-#define PB23_PF_USB_PWR		(GPIO_PORTB | GPIO_PF | 23)
-#define PB24_PF_USB_OC		(GPIO_PORTB | GPIO_PF | 24)
-#define PB26_PF_USBH1_FS	(GPIO_PORTB | GPIO_PF | 26)
-#define PB27_PF_USBH1_OE	(GPIO_PORTB | GPIO_PF | 27)
-#define PB28_PF_USBH1_TXDM	(GPIO_PORTB | GPIO_PF | 28)
-#define PB29_PF_USBH1_TXDP	(GPIO_PORTB | GPIO_PF | 29)
-#define PB30_PF_USBH1_RXDM	(GPIO_PORTB | GPIO_PF | 30)
-#define PB31_PF_USBH1_RXDP	(GPIO_PORTB | GPIO_PF | 31)
-#define PC14_PF_TOUT		(GPIO_PORTC | GPIO_PF | 14)
-#define PC15_PF_TIN		(GPIO_PORTC | GPIO_PF | 15)
-#define PC20_PF_SSI1_FS		(GPIO_PORTC | GPIO_PF | GPIO_IN | 20)
-#define PC21_PF_SSI1_RXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 21)
-#define PC22_PF_SSI1_TXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 22)
-#define PC23_PF_SSI1_CLK	(GPIO_PORTC | GPIO_PF | GPIO_IN | 23)
-#define PC24_PF_SSI2_FS		(GPIO_PORTC | GPIO_PF | GPIO_IN | 24)
-#define PC25_PF_SSI2_RXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 25)
-#define PC26_PF_SSI2_TXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 26)
-#define PC27_PF_SSI2_CLK	(GPIO_PORTC | GPIO_PF | GPIO_IN | 27)
-#define PC28_PF_SSI3_FS		(GPIO_PORTC | GPIO_PF | GPIO_IN | 28)
-#define PC29_PF_SSI3_RXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 29)
-#define PC30_PF_SSI3_TXD	(GPIO_PORTC | GPIO_PF | GPIO_IN | 30)
-#define PC31_PF_SSI3_CLK	(GPIO_PORTC | GPIO_PF | GPIO_IN | 31)
-#define PD17_PF_I2C_DATA	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 17)
-#define PD18_PF_I2C_CLK		(GPIO_PORTD | GPIO_PF | GPIO_OUT | 18)
-#define PD19_PF_CSPI2_SS2	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 19)
-#define PD20_PF_CSPI2_SS1	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 20)
-#define PD21_PF_CSPI2_SS0	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 21)
-#define PD22_PF_CSPI2_SCLK	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 22)
-#define PD23_PF_CSPI2_MISO	(GPIO_PORTD | GPIO_PF | GPIO_IN | 23)
-#define PD24_PF_CSPI2_MOSI	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 24)
-#define PD25_PF_CSPI1_RDY	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 25)
-#define PD26_PF_CSPI1_SS2	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 26)
-#define PD27_PF_CSPI1_SS1	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 27)
-#define PD28_PF_CSPI1_SS0	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 28)
-#define PD29_PF_CSPI1_SCLK	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 29)
-#define PD30_PF_CSPI1_MISO	(GPIO_PORTD | GPIO_PF | GPIO_IN | 30)
-#define PD31_PF_CSPI1_MOSI	(GPIO_PORTD | GPIO_PF | GPIO_OUT | 31)
-#define PE3_PF_UART2_CTS	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 3)
-#define PE4_PF_UART2_RTS	(GPIO_PORTE | GPIO_PF | GPIO_IN | 4)
-#define PE5_PF_PWMO		(GPIO_PORTE | GPIO_PF | 5)
-#define PE6_PF_UART2_TXD	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 6)
-#define PE7_PF_UART2_RXD	(GPIO_PORTE | GPIO_PF | GPIO_IN | 7)
-#define PE8_PF_UART3_TXD	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 8)
-#define PE9_PF_UART3_RXD	(GPIO_PORTE | GPIO_PF | GPIO_IN | 9)
-#define PE10_PF_UART3_CTS	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 10)
-#define PE11_PF_UART3_RTS	(GPIO_PORTE | GPIO_PF | GPIO_IN | 11)
-#define PE12_PF_UART1_TXD	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 12)
-#define PE13_PF_UART1_RXD	(GPIO_PORTE | GPIO_PF | GPIO_IN | 13)
-#define PE14_PF_UART1_CTS	(GPIO_PORTE | GPIO_PF | GPIO_OUT | 14)
-#define PE15_PF_UART1_RTS	(GPIO_PORTE | GPIO_PF | GPIO_IN | 15)
-#define PE16_PF_RTCK		(GPIO_PORTE | GPIO_PF | GPIO_OUT | 16)
-#define PE17_PF_RESET_OUT	(GPIO_PORTE | GPIO_PF | 17)
-#define PE18_PF_SD1_D0		(GPIO_PORTE | GPIO_PF | 18)
-#define PE19_PF_SD1_D1		(GPIO_PORTE | GPIO_PF | 19)
-#define PE20_PF_SD1_D2		(GPIO_PORTE | GPIO_PF | 20)
-#define PE21_PF_SD1_D3		(GPIO_PORTE | GPIO_PF | 21)
-#define PE22_PF_SD1_CMD		(GPIO_PORTE | GPIO_PF | 22)
-#define PE23_PF_SD1_CLK		(GPIO_PORTE | GPIO_PF | 23)
-#define PF0_PF_NRFB		(GPIO_PORTF | GPIO_PF | 0)
-#define PF2_PF_NFWP		(GPIO_PORTF | GPIO_PF | 2)
-#define PF4_PF_NFALE		(GPIO_PORTF | GPIO_PF | 4)
-#define PF5_PF_NFRE		(GPIO_PORTF | GPIO_PF | 5)
-#define PF6_PF_NFWE		(GPIO_PORTF | GPIO_PF | 6)
-#define PF15_PF_CLKO		(GPIO_PORTF | GPIO_PF | 15)
-#define PF21_PF_CS4		(GPIO_PORTF | GPIO_PF | 21)
-#define PF22_PF_CS5		(GPIO_PORTF | GPIO_PF | 22)
-
-/* Alternate GPIO pin functions */
-
-#define PB26_AF_UART4_RTS	(GPIO_PORTB | GPIO_AF | GPIO_IN | 26)
-#define PB28_AF_UART4_TXD	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 28)
-#define PB29_AF_UART4_CTS	(GPIO_PORTB | GPIO_AF | GPIO_OUT | 29)
-#define PB31_AF_UART4_RXD	(GPIO_PORTB | GPIO_AF | GPIO_IN | 31)
-#define PC28_AF_SLCDC2_D0	(GPIO_PORTC | GPIO_AF | 28)
-#define PC29_AF_SLCDC2_RS	(GPIO_PORTC | GPIO_AF | 29)
-#define PC30_AF_SLCDC2_CS	(GPIO_PORTC | GPIO_AF | 30)
-#define PC31_AF_SLCDC2_CLK	(GPIO_PORTC | GPIO_AF | 31)
-#define PD19_AF_USBH2_DATA4	(GPIO_PORTD | GPIO_AF | 19)
-#define PD20_AF_USBH2_DATA3	(GPIO_PORTD | GPIO_AF | 20)
-#define PD21_AF_USBH2_DATA6	(GPIO_PORTD | GPIO_AF | 21)
-#define PD22_AF_USBH2_DATA0	(GPIO_PORTD | GPIO_AF | 22)
-#define PD23_AF_USBH2_DATA2	(GPIO_PORTD | GPIO_AF | 23)
-#define PD24_AF_USBH2_DATA1	(GPIO_PORTD | GPIO_AF | 24)
-#define PD26_AF_USBH2_DATA5	(GPIO_PORTD | GPIO_AF | 26)
-#define PE0_AF_KP_COL6		(GPIO_PORTE | GPIO_AF | 0)
-#define PE1_AF_KP_ROW6		(GPIO_PORTE | GPIO_AF | 1)
-#define PE2_AF_KP_ROW7		(GPIO_PORTE | GPIO_AF | 2)
-#define PE3_AF_KP_COL7		(GPIO_PORTE | GPIO_AF | 3)
-#define PE4_AF_KP_ROW7		(GPIO_PORTE | GPIO_AF | 4)
-#define PE6_AF_KP_COL6		(GPIO_PORTE | GPIO_AF | 6)
-#define PE7_AF_KP_ROW6		(GPIO_PORTE | GPIO_AF | 7)
-#define PE16_AF_OWIRE		(GPIO_PORTE | GPIO_AF | 16)
-#define PE18_AF_CSPI3_MISO	(GPIO_PORTE | GPIO_AF | GPIO_IN | 18)
-#define PE21_AF_CSPI3_SS	(GPIO_PORTE | GPIO_AF | GPIO_OUT | 21)
-#define PE22_AF_CSPI3_MOSI	(GPIO_PORTE | GPIO_AF | GPIO_OUT | 22)
-#define PE23_AF_CSPI3_SCLK	(GPIO_PORTE | GPIO_AF | GPIO_OUT | 23)
-
-/* AIN GPIO pin functions */
-
-#define PA6_AIN_SLCDC1_DAT0	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 6)
-#define PA7_AIN_SLCDC1_DAT1	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 7)
-#define PA8_AIN_SLCDC1_DAT2	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 8)
-#define PA0_AIN_SLCDC1_DAT3	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 0)
-#define PA11_AIN_SLCDC1_DAT5	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 11)
-#define PA13_AIN_SLCDC1_DAT7	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 13)
-#define PA15_AIN_SLCDC1_DAT9	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 15)
-#define PA17_AIN_SLCDC1_DAT11	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 17)
-#define PA19_AIN_SLCDC1_DAT13	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 19)
-#define PA21_AIN_SLCDC1_DAT15	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 21)
-#define PA22_AIN_EXT_DMAGRANT	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 22)
-#define PA24_AIN_SLCDC1_D0	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 24)
-#define PA25_AIN_SLCDC1_RS	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 25)
-#define PA26_AIN_SLCDC1_CS	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 26)
-#define PA27_AIN_SLCDC1_CLK	(GPIO_PORTA | GPIO_AIN | GPIO_OUT | 27)
-#define PB6_AIN_SLCDC1_D0	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 6)
-#define PB7_AIN_SLCDC1_RS	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 7)
-#define PB8_AIN_SLCDC1_CS	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 8)
-#define PB9_AIN_SLCDC1_CLK	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 9)
-#define PB25_AIN_SLCDC1_DAT0	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 25)
-#define PB26_AIN_SLCDC1_DAT1	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 26)
-#define PB27_AIN_SLCDC1_DAT2	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 27)
-#define PB28_AIN_SLCDC1_DAT3	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 28)
-#define PB29_AIN_SLCDC1_DAT4	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 29)
-#define PB30_AIN_SLCDC1_DAT5	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 30)
-#define PB31_AIN_SLCDC1_DAT6	(GPIO_PORTB | GPIO_AIN | GPIO_OUT | 31)
-#define PC5_AIN_SLCDC1_DAT7	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 5)
-#define PC6_AIN_SLCDC1_DAT8	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 6)
-#define PC7_AIN_SLCDC1_DAT9	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 7)
-#define PC8_AIN_SLCDC1_DAT10	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 8)
-#define PC9_AIN_SLCDC1_DAT11	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 9)
-#define PC10_AIN_SLCDC1_DAT12	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 10)
-#define PC11_AIN_SLCDC1_DAT13	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 11)
-#define PC12_AIN_SLCDC1_DAT14	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 12)
-#define PC13_AIN_SLCDC1_DAT15	(GPIO_PORTC | GPIO_AIN | GPIO_OUT | 13)
-#define PE5_AIN_PC_SPKOUT	(GPIO_PORTE | GPIO_AIN | GPIO_OUT | 5)
-
-/* BIN GPIO pin functions */
-
-#define PE5_BIN_TOUT2		(GPIO_PORTE | GPIO_BIN | GPIO_OUT | 5)
-
-/* CIN GPIO pin functions */
-
-#define PA14_CIN_SLCDC1_DAT0	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 14)
-#define PA15_CIN_SLCDC1_DAT1	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 15)
-#define PA16_CIN_SLCDC1_DAT2	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 16)
-#define PA17_CIN_SLCDC1_DAT3	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 17)
-#define PA18_CIN_SLCDC1_DAT4	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 18)
-#define PA19_CIN_SLCDC1_DAT5	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 19)
-#define PA20_CIN_SLCDC1_DAT6	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 20)
-#define PA21_CIN_SLCDC1_DAT7	(GPIO_PORTA | GPIO_CIN | GPIO_OUT | 21)
-#define PB30_CIN_UART4_CTS	(GPIO_PORTB | GPIO_CIN | GPIO_OUT | 30)
-#define PE5_CIN_TOUT3		(GPIO_PORTE | GPIO_CIN | GPIO_OUT | 5)
-
-/* AOUT GPIO pin functions */
-
-#define PB29_AOUT_UART4_RXD	(GPIO_PORTB | GPIO_AOUT | GPIO_IN | 29)
-#define PB31_AOUT_UART4_RTS	(GPIO_PORTB | GPIO_AOUT | GPIO_IN | 31)
-#define PC8_AOUT_USBOTG_TXR_INT (GPIO_PORTC | GPIO_AOUT | GPIO_IN | 8)
-#define PC15_AOUT_WKGD		(GPIO_PORTC | GPIO_AOUT | GPIO_IN | 15)
-#define PF21_AOUT_DTACK		(GPIO_PORTF | GPIO_AOUT | GPIO_IN | 21)
-
-#endif /* ifndef __MACH_IOMUX_MX2x_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx3.h b/arch/arm/mach-imx/iomux-mx3.h
deleted file mode 100644
index 99270a183d47..000000000000
--- a/arch/arm/mach-imx/iomux-mx3.h
+++ /dev/null
@@ -1,706 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- */
-#ifndef __MACH_IOMUX_MX3_H__
-#define __MACH_IOMUX_MX3_H__
-
-#include <linux/types.h>
-/*
- * various IOMUX output functions
- */
-
-#define	IOMUX_OCONFIG_GPIO (0 << 4)	/* used as GPIO */
-#define	IOMUX_OCONFIG_FUNC (1 << 4)	/* used as function */
-#define	IOMUX_OCONFIG_ALT1 (2 << 4)	/* used as alternate function 1 */
-#define	IOMUX_OCONFIG_ALT2 (3 << 4)	/* used as alternate function 2 */
-#define	IOMUX_OCONFIG_ALT3 (4 << 4)	/* used as alternate function 3 */
-#define	IOMUX_OCONFIG_ALT4 (5 << 4)	/* used as alternate function 4 */
-#define	IOMUX_OCONFIG_ALT5 (6 << 4)	/* used as alternate function 5 */
-#define	IOMUX_OCONFIG_ALT6 (7 << 4)	/* used as alternate function 6 */
-#define	IOMUX_ICONFIG_NONE  0		/* not configured for input */
-#define	IOMUX_ICONFIG_GPIO  1		/* used as GPIO */
-#define	IOMUX_ICONFIG_FUNC  2		/* used as function */
-#define	IOMUX_ICONFIG_ALT1  4		/* used as alternate function 1 */
-#define	IOMUX_ICONFIG_ALT2  8		/* used as alternate function 2 */
-
-#define IOMUX_CONFIG_GPIO (IOMUX_OCONFIG_GPIO | IOMUX_ICONFIG_GPIO)
-#define IOMUX_CONFIG_FUNC (IOMUX_OCONFIG_FUNC | IOMUX_ICONFIG_FUNC)
-#define IOMUX_CONFIG_ALT1 (IOMUX_OCONFIG_ALT1 | IOMUX_ICONFIG_ALT1)
-#define IOMUX_CONFIG_ALT2 (IOMUX_OCONFIG_ALT2 | IOMUX_ICONFIG_ALT2)
-
-/*
- * various IOMUX pad functions
- */
-enum iomux_pad_config {
-	PAD_CTL_NOLOOPBACK	= 0x0 << 9,
-	PAD_CTL_LOOPBACK	= 0x1 << 9,
-	PAD_CTL_PKE_NONE	= 0x0 << 8,
-	PAD_CTL_PKE_ENABLE	= 0x1 << 8,
-	PAD_CTL_PUE_KEEPER	= 0x0 << 7,
-	PAD_CTL_PUE_PUD		= 0x1 << 7,
-	PAD_CTL_100K_PD		= 0x0 << 5,
-	PAD_CTL_100K_PU		= 0x1 << 5,
-	PAD_CTL_47K_PU		= 0x2 << 5,
-	PAD_CTL_22K_PU		= 0x3 << 5,
-	PAD_CTL_HYS_CMOS	= 0x0 << 4,
-	PAD_CTL_HYS_SCHMITZ	= 0x1 << 4,
-	PAD_CTL_ODE_CMOS	= 0x0 << 3,
-	PAD_CTL_ODE_OpenDrain	= 0x1 << 3,
-	PAD_CTL_DRV_NORMAL	= 0x0 << 1,
-	PAD_CTL_DRV_HIGH	= 0x1 << 1,
-	PAD_CTL_DRV_MAX		= 0x2 << 1,
-	PAD_CTL_SRE_SLOW	= 0x0 << 0,
-	PAD_CTL_SRE_FAST	= 0x1 << 0
-};
-
-/*
- * various IOMUX general purpose functions
- */
-enum iomux_gp_func {
-	MUX_PGP_FIRI			= 1 << 0,
-	MUX_DDR_MODE			= 1 << 1,
-	MUX_PGP_CSPI_BB			= 1 << 2,
-	MUX_PGP_ATA_1			= 1 << 3,
-	MUX_PGP_ATA_2			= 1 << 4,
-	MUX_PGP_ATA_3			= 1 << 5,
-	MUX_PGP_ATA_4			= 1 << 6,
-	MUX_PGP_ATA_5			= 1 << 7,
-	MUX_PGP_ATA_6			= 1 << 8,
-	MUX_PGP_ATA_7			= 1 << 9,
-	MUX_PGP_ATA_8			= 1 << 10,
-	MUX_PGP_UH2			= 1 << 11,
-	MUX_SDCTL_CSD0_SEL		= 1 << 12,
-	MUX_SDCTL_CSD1_SEL		= 1 << 13,
-	MUX_CSPI1_UART3			= 1 << 14,
-	MUX_EXTDMAREQ2_MBX_SEL		= 1 << 15,
-	MUX_TAMPER_DETECT_EN		= 1 << 16,
-	MUX_PGP_USB_4WIRE		= 1 << 17,
-	MUX_PGP_USB_COMMON		= 1 << 18,
-	MUX_SDHC_MEMSTICK1		= 1 << 19,
-	MUX_SDHC_MEMSTICK2		= 1 << 20,
-	MUX_PGP_SPLL_BYP		= 1 << 21,
-	MUX_PGP_UPLL_BYP		= 1 << 22,
-	MUX_PGP_MSHC1_CLK_SEL		= 1 << 23,
-	MUX_PGP_MSHC2_CLK_SEL		= 1 << 24,
-	MUX_CSPI3_UART5_SEL		= 1 << 25,
-	MUX_PGP_ATA_9			= 1 << 26,
-	MUX_PGP_USB_SUSPEND		= 1 << 27,
-	MUX_PGP_USB_OTG_LOOPBACK	= 1 << 28,
-	MUX_PGP_USB_HS1_LOOPBACK	= 1 << 29,
-	MUX_PGP_USB_HS2_LOOPBACK	= 1 << 30,
-	MUX_CLKO_DDR_MODE		= 1 << 31,
-};
-
-/*
- * setups a single pin:
- * 	- reserves the pin so that it is not claimed by another driver
- * 	- setups the iomux according to the configuration
- * 	- if the pin is configured as a GPIO, we claim it through kernel gpiolib
- */
-int mxc_iomux_alloc_pin(unsigned int pin, const char *label);
-/*
- * setups multiple pins
- * convenient way to call the above function with tables
- */
-int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
-		const char *label);
-
-/*
- * releases a single pin:
- * 	- make it available for a future use by another driver
- * 	- frees the GPIO if the pin was configured as GPIO
- * 	- DOES NOT reconfigure the IOMUX in its reset state
- */
-void mxc_iomux_release_pin(unsigned int pin);
-/*
- * releases multiple pins
- * convenvient way to call the above function with tables
- */
-void mxc_iomux_release_multiple_pins(const unsigned int *pin_list, int count);
-
-/*
- * This function enables/disables the general purpose function for a particular
- * signal.
- */
-void mxc_iomux_set_gpr(enum iomux_gp_func, bool en);
-
-/*
- * This function only configures the iomux hardware.
- * It is called by the setup functions and should not be called directly anymore.
- * It is here visible for backward compatibility
- */
-void mxc_iomux_mode(unsigned int pin_mode);
-
-#define IOMUX_PADNUM_MASK	0x1ff
-#define IOMUX_GPIONUM_SHIFT	9
-#define IOMUX_GPIONUM_MASK	(0xff << IOMUX_GPIONUM_SHIFT)
-#define IOMUX_MODE_SHIFT	17
-#define IOMUX_MODE_MASK	(0xff << IOMUX_MODE_SHIFT)
-
-#define IOMUX_PIN(gpionum, padnum) \
-	(((gpionum << IOMUX_GPIONUM_SHIFT) & IOMUX_GPIONUM_MASK) | \
-	 (padnum & IOMUX_PADNUM_MASK))
-
-#define IOMUX_MODE(pin, mode) (pin | mode << IOMUX_MODE_SHIFT)
-
-#define IOMUX_TO_GPIO(iomux_pin) \
-	((iomux_pin & IOMUX_GPIONUM_MASK) >> IOMUX_GPIONUM_SHIFT)
-
-/*
- * This enumeration is constructed based on the Section
- * "sw_pad_ctl & sw_mux_ctl details" of the MX31 IC Spec. Each enumerated
- * value is constructed based on the rules described above.
- */
-
-enum iomux_pins {
-	MX31_PIN_TTM_PAD	= IOMUX_PIN(0xff,   0),
-	MX31_PIN_CSPI3_SPI_RDY	= IOMUX_PIN(0xff,   1),
-	MX31_PIN_CSPI3_SCLK	= IOMUX_PIN(0xff,   2),
-	MX31_PIN_CSPI3_MISO	= IOMUX_PIN(0xff,   3),
-	MX31_PIN_CSPI3_MOSI	= IOMUX_PIN(0xff,   4),
-	MX31_PIN_CLKSS		= IOMUX_PIN(0xff,   5),
-	MX31_PIN_CE_CONTROL	= IOMUX_PIN(0xff,   6),
-	MX31_PIN_ATA_RESET_B	= IOMUX_PIN(95,     7),
-	MX31_PIN_ATA_DMACK	= IOMUX_PIN(94,     8),
-	MX31_PIN_ATA_DIOW	= IOMUX_PIN(93,     9),
-	MX31_PIN_ATA_DIOR	= IOMUX_PIN(92,    10),
-	MX31_PIN_ATA_CS1	= IOMUX_PIN(91,    11),
-	MX31_PIN_ATA_CS0	= IOMUX_PIN(90,    12),
-	MX31_PIN_SD1_DATA3	= IOMUX_PIN(63,    13),
-	MX31_PIN_SD1_DATA2	= IOMUX_PIN(62,    14),
-	MX31_PIN_SD1_DATA1	= IOMUX_PIN(61,    15),
-	MX31_PIN_SD1_DATA0	= IOMUX_PIN(60,    16),
-	MX31_PIN_SD1_CLK	= IOMUX_PIN(59,    17),
-	MX31_PIN_SD1_CMD	= IOMUX_PIN(58,    18),
-	MX31_PIN_D3_SPL		= IOMUX_PIN(0xff,  19),
-	MX31_PIN_D3_CLS		= IOMUX_PIN(0xff,  20),
-	MX31_PIN_D3_REV		= IOMUX_PIN(0xff,  21),
-	MX31_PIN_CONTRAST	= IOMUX_PIN(0xff,  22),
-	MX31_PIN_VSYNC3		= IOMUX_PIN(0xff,  23),
-	MX31_PIN_READ		= IOMUX_PIN(0xff,  24),
-	MX31_PIN_WRITE		= IOMUX_PIN(0xff,  25),
-	MX31_PIN_PAR_RS		= IOMUX_PIN(0xff,  26),
-	MX31_PIN_SER_RS		= IOMUX_PIN(89,    27),
-	MX31_PIN_LCS1		= IOMUX_PIN(88,    28),
-	MX31_PIN_LCS0		= IOMUX_PIN(87,    29),
-	MX31_PIN_SD_D_CLK	= IOMUX_PIN(86,    30),
-	MX31_PIN_SD_D_IO	= IOMUX_PIN(85,    31),
-	MX31_PIN_SD_D_I		= IOMUX_PIN(84,    32),
-	MX31_PIN_DRDY0		= IOMUX_PIN(0xff,  33),
-	MX31_PIN_FPSHIFT	= IOMUX_PIN(0xff,  34),
-	MX31_PIN_HSYNC		= IOMUX_PIN(0xff,  35),
-	MX31_PIN_VSYNC0		= IOMUX_PIN(0xff,  36),
-	MX31_PIN_LD17		= IOMUX_PIN(0xff,  37),
-	MX31_PIN_LD16		= IOMUX_PIN(0xff,  38),
-	MX31_PIN_LD15		= IOMUX_PIN(0xff,  39),
-	MX31_PIN_LD14		= IOMUX_PIN(0xff,  40),
-	MX31_PIN_LD13		= IOMUX_PIN(0xff,  41),
-	MX31_PIN_LD12		= IOMUX_PIN(0xff,  42),
-	MX31_PIN_LD11		= IOMUX_PIN(0xff,  43),
-	MX31_PIN_LD10		= IOMUX_PIN(0xff,  44),
-	MX31_PIN_LD9		= IOMUX_PIN(0xff,  45),
-	MX31_PIN_LD8		= IOMUX_PIN(0xff,  46),
-	MX31_PIN_LD7		= IOMUX_PIN(0xff,  47),
-	MX31_PIN_LD6		= IOMUX_PIN(0xff,  48),
-	MX31_PIN_LD5		= IOMUX_PIN(0xff,  49),
-	MX31_PIN_LD4		= IOMUX_PIN(0xff,  50),
-	MX31_PIN_LD3		= IOMUX_PIN(0xff,  51),
-	MX31_PIN_LD2		= IOMUX_PIN(0xff,  52),
-	MX31_PIN_LD1		= IOMUX_PIN(0xff,  53),
-	MX31_PIN_LD0		= IOMUX_PIN(0xff,  54),
-	MX31_PIN_USBH2_DATA1	= IOMUX_PIN(0xff,  55),
-	MX31_PIN_USBH2_DATA0	= IOMUX_PIN(0xff,  56),
-	MX31_PIN_USBH2_NXT	= IOMUX_PIN(0xff,  57),
-	MX31_PIN_USBH2_STP	= IOMUX_PIN(0xff,  58),
-	MX31_PIN_USBH2_DIR	= IOMUX_PIN(0xff,  59),
-	MX31_PIN_USBH2_CLK	= IOMUX_PIN(0xff,  60),
-	MX31_PIN_USBOTG_DATA7	= IOMUX_PIN(0xff,  61),
-	MX31_PIN_USBOTG_DATA6	= IOMUX_PIN(0xff,  62),
-	MX31_PIN_USBOTG_DATA5	= IOMUX_PIN(0xff,  63),
-	MX31_PIN_USBOTG_DATA4	= IOMUX_PIN(0xff,  64),
-	MX31_PIN_USBOTG_DATA3	= IOMUX_PIN(0xff,  65),
-	MX31_PIN_USBOTG_DATA2	= IOMUX_PIN(0xff,  66),
-	MX31_PIN_USBOTG_DATA1	= IOMUX_PIN(0xff,  67),
-	MX31_PIN_USBOTG_DATA0	= IOMUX_PIN(0xff,  68),
-	MX31_PIN_USBOTG_NXT	= IOMUX_PIN(0xff,  69),
-	MX31_PIN_USBOTG_STP	= IOMUX_PIN(0xff,  70),
-	MX31_PIN_USBOTG_DIR	= IOMUX_PIN(0xff,  71),
-	MX31_PIN_USBOTG_CLK	= IOMUX_PIN(0xff,  72),
-	MX31_PIN_USB_BYP	= IOMUX_PIN(31,    73),
-	MX31_PIN_USB_OC		= IOMUX_PIN(30,    74),
-	MX31_PIN_USB_PWR	= IOMUX_PIN(29,    75),
-	MX31_PIN_SJC_MOD	= IOMUX_PIN(0xff,  76),
-	MX31_PIN_DE_B		= IOMUX_PIN(0xff,  77),
-	MX31_PIN_TRSTB		= IOMUX_PIN(0xff,  78),
-	MX31_PIN_TDO		= IOMUX_PIN(0xff,  79),
-	MX31_PIN_TDI		= IOMUX_PIN(0xff,  80),
-	MX31_PIN_TMS		= IOMUX_PIN(0xff,  81),
-	MX31_PIN_TCK		= IOMUX_PIN(0xff,  82),
-	MX31_PIN_RTCK		= IOMUX_PIN(0xff,  83),
-	MX31_PIN_KEY_COL7	= IOMUX_PIN(57,    84),
-	MX31_PIN_KEY_COL6	= IOMUX_PIN(56,    85),
-	MX31_PIN_KEY_COL5	= IOMUX_PIN(55,    86),
-	MX31_PIN_KEY_COL4	= IOMUX_PIN(54,    87),
-	MX31_PIN_KEY_COL3	= IOMUX_PIN(0xff,  88),
-	MX31_PIN_KEY_COL2	= IOMUX_PIN(0xff,  89),
-	MX31_PIN_KEY_COL1	= IOMUX_PIN(0xff,  90),
-	MX31_PIN_KEY_COL0	= IOMUX_PIN(0xff,  91),
-	MX31_PIN_KEY_ROW7	= IOMUX_PIN(53,    92),
-	MX31_PIN_KEY_ROW6	= IOMUX_PIN(52,    93),
-	MX31_PIN_KEY_ROW5	= IOMUX_PIN(51,    94),
-	MX31_PIN_KEY_ROW4	= IOMUX_PIN(50,    95),
-	MX31_PIN_KEY_ROW3	= IOMUX_PIN(0xff,  96),
-	MX31_PIN_KEY_ROW2	= IOMUX_PIN(0xff,  97),
-	MX31_PIN_KEY_ROW1	= IOMUX_PIN(0xff,  98),
-	MX31_PIN_KEY_ROW0	= IOMUX_PIN(0xff,  99),
-	MX31_PIN_BATT_LINE	= IOMUX_PIN(49,   100),
-	MX31_PIN_CTS2		= IOMUX_PIN(0xff, 101),
-	MX31_PIN_RTS2		= IOMUX_PIN(0xff, 102),
-	MX31_PIN_TXD2		= IOMUX_PIN(28,   103),
-	MX31_PIN_RXD2		= IOMUX_PIN(27,   104),
-	MX31_PIN_DTR_DCE2	= IOMUX_PIN(48,   105),
-	MX31_PIN_DCD_DTE1	= IOMUX_PIN(47,   106),
-	MX31_PIN_RI_DTE1	= IOMUX_PIN(46,   107),
-	MX31_PIN_DSR_DTE1	= IOMUX_PIN(45,   108),
-	MX31_PIN_DTR_DTE1	= IOMUX_PIN(44,   109),
-	MX31_PIN_DCD_DCE1	= IOMUX_PIN(43,   110),
-	MX31_PIN_RI_DCE1	= IOMUX_PIN(42,   111),
-	MX31_PIN_DSR_DCE1	= IOMUX_PIN(41,   112),
-	MX31_PIN_DTR_DCE1	= IOMUX_PIN(40,   113),
-	MX31_PIN_CTS1		= IOMUX_PIN(39,   114),
-	MX31_PIN_RTS1		= IOMUX_PIN(38,   115),
-	MX31_PIN_TXD1		= IOMUX_PIN(37,   116),
-	MX31_PIN_RXD1		= IOMUX_PIN(36,   117),
-	MX31_PIN_CSPI2_SPI_RDY	= IOMUX_PIN(0xff, 118),
-	MX31_PIN_CSPI2_SCLK	= IOMUX_PIN(0xff, 119),
-	MX31_PIN_CSPI2_SS2	= IOMUX_PIN(0xff, 120),
-	MX31_PIN_CSPI2_SS1	= IOMUX_PIN(0xff, 121),
-	MX31_PIN_CSPI2_SS0	= IOMUX_PIN(0xff, 122),
-	MX31_PIN_CSPI2_MISO	= IOMUX_PIN(0xff, 123),
-	MX31_PIN_CSPI2_MOSI	= IOMUX_PIN(0xff, 124),
-	MX31_PIN_CSPI1_SPI_RDY	= IOMUX_PIN(0xff, 125),
-	MX31_PIN_CSPI1_SCLK	= IOMUX_PIN(0xff, 126),
-	MX31_PIN_CSPI1_SS2	= IOMUX_PIN(0xff, 127),
-	MX31_PIN_CSPI1_SS1	= IOMUX_PIN(0xff, 128),
-	MX31_PIN_CSPI1_SS0	= IOMUX_PIN(0xff, 129),
-	MX31_PIN_CSPI1_MISO	= IOMUX_PIN(0xff, 130),
-	MX31_PIN_CSPI1_MOSI	= IOMUX_PIN(0xff, 131),
-	MX31_PIN_SFS6		= IOMUX_PIN(26,   132),
-	MX31_PIN_SCK6		= IOMUX_PIN(25,   133),
-	MX31_PIN_SRXD6		= IOMUX_PIN(24,   134),
-	MX31_PIN_STXD6		= IOMUX_PIN(23,   135),
-	MX31_PIN_SFS5		= IOMUX_PIN(0xff, 136),
-	MX31_PIN_SCK5		= IOMUX_PIN(0xff, 137),
-	MX31_PIN_SRXD5		= IOMUX_PIN(22,   138),
-	MX31_PIN_STXD5		= IOMUX_PIN(21,   139),
-	MX31_PIN_SFS4		= IOMUX_PIN(0xff, 140),
-	MX31_PIN_SCK4		= IOMUX_PIN(0xff, 141),
-	MX31_PIN_SRXD4		= IOMUX_PIN(20,   142),
-	MX31_PIN_STXD4		= IOMUX_PIN(19,   143),
-	MX31_PIN_SFS3		= IOMUX_PIN(0xff, 144),
-	MX31_PIN_SCK3		= IOMUX_PIN(0xff, 145),
-	MX31_PIN_SRXD3		= IOMUX_PIN(18,   146),
-	MX31_PIN_STXD3		= IOMUX_PIN(17,   147),
-	MX31_PIN_I2C_DAT	= IOMUX_PIN(0xff, 148),
-	MX31_PIN_I2C_CLK	= IOMUX_PIN(0xff, 149),
-	MX31_PIN_CSI_PIXCLK	= IOMUX_PIN(83,   150),
-	MX31_PIN_CSI_HSYNC	= IOMUX_PIN(82,   151),
-	MX31_PIN_CSI_VSYNC	= IOMUX_PIN(81,   152),
-	MX31_PIN_CSI_MCLK	= IOMUX_PIN(80,   153),
-	MX31_PIN_CSI_D15	= IOMUX_PIN(79,   154),
-	MX31_PIN_CSI_D14	= IOMUX_PIN(78,   155),
-	MX31_PIN_CSI_D13	= IOMUX_PIN(77,   156),
-	MX31_PIN_CSI_D12	= IOMUX_PIN(76,   157),
-	MX31_PIN_CSI_D11	= IOMUX_PIN(75,   158),
-	MX31_PIN_CSI_D10	= IOMUX_PIN(74,   159),
-	MX31_PIN_CSI_D9		= IOMUX_PIN(73,   160),
-	MX31_PIN_CSI_D8		= IOMUX_PIN(72,   161),
-	MX31_PIN_CSI_D7		= IOMUX_PIN(71,   162),
-	MX31_PIN_CSI_D6		= IOMUX_PIN(70,   163),
-	MX31_PIN_CSI_D5		= IOMUX_PIN(69,   164),
-	MX31_PIN_CSI_D4		= IOMUX_PIN(68,   165),
-	MX31_PIN_M_GRANT	= IOMUX_PIN(0xff, 166),
-	MX31_PIN_M_REQUEST	= IOMUX_PIN(0xff, 167),
-	MX31_PIN_PC_POE		= IOMUX_PIN(0xff, 168),
-	MX31_PIN_PC_RW_B	= IOMUX_PIN(0xff, 169),
-	MX31_PIN_IOIS16		= IOMUX_PIN(0xff, 170),
-	MX31_PIN_PC_RST		= IOMUX_PIN(0xff, 171),
-	MX31_PIN_PC_BVD2	= IOMUX_PIN(0xff, 172),
-	MX31_PIN_PC_BVD1	= IOMUX_PIN(0xff, 173),
-	MX31_PIN_PC_VS2		= IOMUX_PIN(0xff, 174),
-	MX31_PIN_PC_VS1		= IOMUX_PIN(0xff, 175),
-	MX31_PIN_PC_PWRON	= IOMUX_PIN(0xff, 176),
-	MX31_PIN_PC_READY	= IOMUX_PIN(0xff, 177),
-	MX31_PIN_PC_WAIT_B	= IOMUX_PIN(0xff, 178),
-	MX31_PIN_PC_CD2_B	= IOMUX_PIN(0xff, 179),
-	MX31_PIN_PC_CD1_B	= IOMUX_PIN(0xff, 180),
-	MX31_PIN_D0		= IOMUX_PIN(0xff, 181),
-	MX31_PIN_D1		= IOMUX_PIN(0xff, 182),
-	MX31_PIN_D2		= IOMUX_PIN(0xff, 183),
-	MX31_PIN_D3		= IOMUX_PIN(0xff, 184),
-	MX31_PIN_D4		= IOMUX_PIN(0xff, 185),
-	MX31_PIN_D5		= IOMUX_PIN(0xff, 186),
-	MX31_PIN_D6		= IOMUX_PIN(0xff, 187),
-	MX31_PIN_D7		= IOMUX_PIN(0xff, 188),
-	MX31_PIN_D8		= IOMUX_PIN(0xff, 189),
-	MX31_PIN_D9		= IOMUX_PIN(0xff, 190),
-	MX31_PIN_D10		= IOMUX_PIN(0xff, 191),
-	MX31_PIN_D11		= IOMUX_PIN(0xff, 192),
-	MX31_PIN_D12		= IOMUX_PIN(0xff, 193),
-	MX31_PIN_D13		= IOMUX_PIN(0xff, 194),
-	MX31_PIN_D14		= IOMUX_PIN(0xff, 195),
-	MX31_PIN_D15		= IOMUX_PIN(0xff, 196),
-	MX31_PIN_NFRB		= IOMUX_PIN(16,   197),
-	MX31_PIN_NFCE_B		= IOMUX_PIN(15,   198),
-	MX31_PIN_NFWP_B		= IOMUX_PIN(14,   199),
-	MX31_PIN_NFCLE		= IOMUX_PIN(13,   200),
-	MX31_PIN_NFALE		= IOMUX_PIN(12,   201),
-	MX31_PIN_NFRE_B		= IOMUX_PIN(11,   202),
-	MX31_PIN_NFWE_B		= IOMUX_PIN(10,   203),
-	MX31_PIN_SDQS3		= IOMUX_PIN(0xff, 204),
-	MX31_PIN_SDQS2		= IOMUX_PIN(0xff, 205),
-	MX31_PIN_SDQS1		= IOMUX_PIN(0xff, 206),
-	MX31_PIN_SDQS0		= IOMUX_PIN(0xff, 207),
-	MX31_PIN_SDCLK_B	= IOMUX_PIN(0xff, 208),
-	MX31_PIN_SDCLK		= IOMUX_PIN(0xff, 209),
-	MX31_PIN_SDCKE1		= IOMUX_PIN(0xff, 210),
-	MX31_PIN_SDCKE0		= IOMUX_PIN(0xff, 211),
-	MX31_PIN_SDWE		= IOMUX_PIN(0xff, 212),
-	MX31_PIN_CAS		= IOMUX_PIN(0xff, 213),
-	MX31_PIN_RAS		= IOMUX_PIN(0xff, 214),
-	MX31_PIN_RW		= IOMUX_PIN(0xff, 215),
-	MX31_PIN_BCLK		= IOMUX_PIN(0xff, 216),
-	MX31_PIN_LBA		= IOMUX_PIN(0xff, 217),
-	MX31_PIN_ECB		= IOMUX_PIN(0xff, 218),
-	MX31_PIN_CS5		= IOMUX_PIN(0xff, 219),
-	MX31_PIN_CS4		= IOMUX_PIN(0xff, 220),
-	MX31_PIN_CS3		= IOMUX_PIN(0xff, 221),
-	MX31_PIN_CS2		= IOMUX_PIN(0xff, 222),
-	MX31_PIN_CS1		= IOMUX_PIN(0xff, 223),
-	MX31_PIN_CS0		= IOMUX_PIN(0xff, 224),
-	MX31_PIN_OE		= IOMUX_PIN(0xff, 225),
-	MX31_PIN_EB1		= IOMUX_PIN(0xff, 226),
-	MX31_PIN_EB0		= IOMUX_PIN(0xff, 227),
-	MX31_PIN_DQM3		= IOMUX_PIN(0xff, 228),
-	MX31_PIN_DQM2		= IOMUX_PIN(0xff, 229),
-	MX31_PIN_DQM1		= IOMUX_PIN(0xff, 230),
-	MX31_PIN_DQM0		= IOMUX_PIN(0xff, 231),
-	MX31_PIN_SD31		= IOMUX_PIN(0xff, 232),
-	MX31_PIN_SD30		= IOMUX_PIN(0xff, 233),
-	MX31_PIN_SD29		= IOMUX_PIN(0xff, 234),
-	MX31_PIN_SD28		= IOMUX_PIN(0xff, 235),
-	MX31_PIN_SD27		= IOMUX_PIN(0xff, 236),
-	MX31_PIN_SD26		= IOMUX_PIN(0xff, 237),
-	MX31_PIN_SD25		= IOMUX_PIN(0xff, 238),
-	MX31_PIN_SD24		= IOMUX_PIN(0xff, 239),
-	MX31_PIN_SD23		= IOMUX_PIN(0xff, 240),
-	MX31_PIN_SD22		= IOMUX_PIN(0xff, 241),
-	MX31_PIN_SD21		= IOMUX_PIN(0xff, 242),
-	MX31_PIN_SD20		= IOMUX_PIN(0xff, 243),
-	MX31_PIN_SD19		= IOMUX_PIN(0xff, 244),
-	MX31_PIN_SD18		= IOMUX_PIN(0xff, 245),
-	MX31_PIN_SD17		= IOMUX_PIN(0xff, 246),
-	MX31_PIN_SD16		= IOMUX_PIN(0xff, 247),
-	MX31_PIN_SD15		= IOMUX_PIN(0xff, 248),
-	MX31_PIN_SD14		= IOMUX_PIN(0xff, 249),
-	MX31_PIN_SD13		= IOMUX_PIN(0xff, 250),
-	MX31_PIN_SD12		= IOMUX_PIN(0xff, 251),
-	MX31_PIN_SD11		= IOMUX_PIN(0xff, 252),
-	MX31_PIN_SD10		= IOMUX_PIN(0xff, 253),
-	MX31_PIN_SD9		= IOMUX_PIN(0xff, 254),
-	MX31_PIN_SD8		= IOMUX_PIN(0xff, 255),
-	MX31_PIN_SD7		= IOMUX_PIN(0xff, 256),
-	MX31_PIN_SD6		= IOMUX_PIN(0xff, 257),
-	MX31_PIN_SD5		= IOMUX_PIN(0xff, 258),
-	MX31_PIN_SD4		= IOMUX_PIN(0xff, 259),
-	MX31_PIN_SD3		= IOMUX_PIN(0xff, 260),
-	MX31_PIN_SD2		= IOMUX_PIN(0xff, 261),
-	MX31_PIN_SD1		= IOMUX_PIN(0xff, 262),
-	MX31_PIN_SD0		= IOMUX_PIN(0xff, 263),
-	MX31_PIN_SDBA0		= IOMUX_PIN(0xff, 264),
-	MX31_PIN_SDBA1		= IOMUX_PIN(0xff, 265),
-	MX31_PIN_A25		= IOMUX_PIN(0xff, 266),
-	MX31_PIN_A24		= IOMUX_PIN(0xff, 267),
-	MX31_PIN_A23		= IOMUX_PIN(0xff, 268),
-	MX31_PIN_A22		= IOMUX_PIN(0xff, 269),
-	MX31_PIN_A21		= IOMUX_PIN(0xff, 270),
-	MX31_PIN_A20		= IOMUX_PIN(0xff, 271),
-	MX31_PIN_A19		= IOMUX_PIN(0xff, 272),
-	MX31_PIN_A18		= IOMUX_PIN(0xff, 273),
-	MX31_PIN_A17		= IOMUX_PIN(0xff, 274),
-	MX31_PIN_A16		= IOMUX_PIN(0xff, 275),
-	MX31_PIN_A14		= IOMUX_PIN(0xff, 276),
-	MX31_PIN_A15		= IOMUX_PIN(0xff, 277),
-	MX31_PIN_A13		= IOMUX_PIN(0xff, 278),
-	MX31_PIN_A12		= IOMUX_PIN(0xff, 279),
-	MX31_PIN_A11		= IOMUX_PIN(0xff, 280),
-	MX31_PIN_MA10		= IOMUX_PIN(0xff, 281),
-	MX31_PIN_A10		= IOMUX_PIN(0xff, 282),
-	MX31_PIN_A9		= IOMUX_PIN(0xff, 283),
-	MX31_PIN_A8		= IOMUX_PIN(0xff, 284),
-	MX31_PIN_A7		= IOMUX_PIN(0xff, 285),
-	MX31_PIN_A6		= IOMUX_PIN(0xff, 286),
-	MX31_PIN_A5		= IOMUX_PIN(0xff, 287),
-	MX31_PIN_A4		= IOMUX_PIN(0xff, 288),
-	MX31_PIN_A3		= IOMUX_PIN(0xff, 289),
-	MX31_PIN_A2		= IOMUX_PIN(0xff, 290),
-	MX31_PIN_A1		= IOMUX_PIN(0xff, 291),
-	MX31_PIN_A0		= IOMUX_PIN(0xff, 292),
-	MX31_PIN_VPG1		= IOMUX_PIN(0xff, 293),
-	MX31_PIN_VPG0		= IOMUX_PIN(0xff, 294),
-	MX31_PIN_DVFS1		= IOMUX_PIN(0xff, 295),
-	MX31_PIN_DVFS0		= IOMUX_PIN(0xff, 296),
-	MX31_PIN_VSTBY		= IOMUX_PIN(0xff, 297),
-	MX31_PIN_POWER_FAIL	= IOMUX_PIN(0xff, 298),
-	MX31_PIN_CKIL		= IOMUX_PIN(0xff, 299),
-	MX31_PIN_BOOT_MODE4	= IOMUX_PIN(0xff, 300),
-	MX31_PIN_BOOT_MODE3	= IOMUX_PIN(0xff, 301),
-	MX31_PIN_BOOT_MODE2	= IOMUX_PIN(0xff, 302),
-	MX31_PIN_BOOT_MODE1	= IOMUX_PIN(0xff, 303),
-	MX31_PIN_BOOT_MODE0	= IOMUX_PIN(0xff, 304),
-	MX31_PIN_CLKO		= IOMUX_PIN(0xff, 305),
-	MX31_PIN_POR_B		= IOMUX_PIN(0xff, 306),
-	MX31_PIN_RESET_IN_B	= IOMUX_PIN(0xff, 307),
-	MX31_PIN_CKIH		= IOMUX_PIN(0xff, 308),
-	MX31_PIN_SIMPD0		= IOMUX_PIN(35,   309),
-	MX31_PIN_SRX0		= IOMUX_PIN(34,   310),
-	MX31_PIN_STX0		= IOMUX_PIN(33,   311),
-	MX31_PIN_SVEN0		= IOMUX_PIN(32,   312),
-	MX31_PIN_SRST0		= IOMUX_PIN(67,   313),
-	MX31_PIN_SCLK0		= IOMUX_PIN(66,   314),
-	MX31_PIN_GPIO3_1	= IOMUX_PIN(65,   315),
-	MX31_PIN_GPIO3_0	= IOMUX_PIN(64,   316),
-	MX31_PIN_GPIO1_6	= IOMUX_PIN( 6,   317),
-	MX31_PIN_GPIO1_5	= IOMUX_PIN( 5,   318),
-	MX31_PIN_GPIO1_4	= IOMUX_PIN( 4,   319),
-	MX31_PIN_GPIO1_3	= IOMUX_PIN( 3,   320),
-	MX31_PIN_GPIO1_2	= IOMUX_PIN( 2,   321),
-	MX31_PIN_GPIO1_1	= IOMUX_PIN( 1,   322),
-	MX31_PIN_GPIO1_0	= IOMUX_PIN( 0,   323),
-	MX31_PIN_PWMO		= IOMUX_PIN( 9,   324),
-	MX31_PIN_WATCHDOG_RST	= IOMUX_PIN(0xff, 325),
-	MX31_PIN_COMPARE	= IOMUX_PIN( 8,   326),
-	MX31_PIN_CAPTURE	= IOMUX_PIN( 7,   327),
-};
-
-#define PIN_MAX 327
-#define NB_PORTS 12 /* NB_PINS/32, we chose 32 pins per "PORT" */
-
-/*
- * Convenience values for use with mxc_iomux_mode()
- *
- * Format here is MX31_PIN_(pin name)__(function)
- */
-#define MX31_PIN_CSPI3_MOSI__RXD3	IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_MISO__TXD3	IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_SCLK__RTS3	IOMUX_MODE(MX31_PIN_CSPI3_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI3_SPI_RDY__CTS3	IOMUX_MODE(MX31_PIN_CSPI3_SPI_RDY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CTS1__CTS1		IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS1__RTS1		IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS1__SFS		IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_TXD1__TXD1		IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_TXD1__SCK		IOMUX_MODE(MX31_PIN_TXD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_RXD1__RXD1		IOMUX_MODE(MX31_PIN_RXD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RXD1__STXDA		IOMUX_MODE(MX31_PIN_RXD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_DCD_DCE1__DCD_DCE1	IOMUX_MODE(MX31_PIN_DCD_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RI_DCE1__RI_DCE1	IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DSR_DCE1__DSR_DCE1	IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DTR_DCE1__DTR_DCE1	IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DTR_DCE1__SRXDA	IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CTS2__CTS2		IOMUX_MODE(MX31_PIN_CTS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RTS2__RTS2		IOMUX_MODE(MX31_PIN_RTS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_TXD2__TXD2		IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_RXD2__RXD2		IOMUX_MODE(MX31_PIN_RXD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DCD_DTE1__DCD_DTE2	IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_RI_DTE1__RI_DTE2	IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_DSR_DTE1__DSR_DTE2	IOMUX_MODE(MX31_PIN_DSR_DTE1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_DTR_DTE1__DTR_DTE2	IOMUX_MODE(MX31_PIN_DTR_DTE1, IOMUX_OCONFIG_ALT3 | IOMUX_ICONFIG_NONE)
-#define MX31_PIN_PC_RST__CTS5		IOMUX_MODE(MX31_PIN_PC_RST, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_VS2__RTS5		IOMUX_MODE(MX31_PIN_PC_VS2, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_BVD2__TXD5		IOMUX_MODE(MX31_PIN_PC_BVD2, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_PC_BVD1__RXD5		IOMUX_MODE(MX31_PIN_PC_BVD1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CSPI1_MOSI__MOSI	IOMUX_MODE(MX31_PIN_CSPI1_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_MISO__MISO	IOMUX_MODE(MX31_PIN_CSPI1_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SCLK__SCLK	IOMUX_MODE(MX31_PIN_CSPI1_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SPI_RDY__SPI_RDY	IOMUX_MODE(MX31_PIN_CSPI1_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS0__SS0		IOMUX_MODE(MX31_PIN_CSPI1_SS0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS1__SS1		IOMUX_MODE(MX31_PIN_CSPI1_SS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_SS2__SS2		IOMUX_MODE(MX31_PIN_CSPI1_SS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MOSI__MOSI	IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MOSI__SCL	IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_MISO__MISO	IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_MISO__SDA	IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_SCLK__SCLK	IOMUX_MODE(MX31_PIN_CSPI2_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SPI_RDY__SPI_RDY	IOMUX_MODE(MX31_PIN_CSPI2_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS0__SS0		IOMUX_MODE(MX31_PIN_CSPI2_SS0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS1__SS1		IOMUX_MODE(MX31_PIN_CSPI2_SS1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI2_SS2__SS2		IOMUX_MODE(MX31_PIN_CSPI2_SS2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_MOSI__MOSI	IOMUX_MODE(MX31_PIN_CSPI3_MOSI, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_MISO__MISO	IOMUX_MODE(MX31_PIN_CSPI3_MISO, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_SCLK__SCLK	IOMUX_MODE(MX31_PIN_CSPI3_SCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI3_SPI_RDY__SPI_RDY	IOMUX_MODE(MX31_PIN_CSPI3_SPI_RDY, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_BATT_LINE__OWIRE	IOMUX_MODE(MX31_PIN_BATT_LINE, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CS4__CS4		IOMUX_MODE(MX31_PIN_CS4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA3__SD1_DATA3	IOMUX_MODE(MX31_PIN_SD1_DATA3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA2__SD1_DATA2	IOMUX_MODE(MX31_PIN_SD1_DATA2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA1__SD1_DATA1	IOMUX_MODE(MX31_PIN_SD1_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_DATA0__SD1_DATA0	IOMUX_MODE(MX31_PIN_SD1_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_CLK__SD1_CLK	IOMUX_MODE(MX31_PIN_SD1_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SD1_CMD__SD1_CMD	IOMUX_MODE(MX31_PIN_SD1_CMD, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_ATA_CS0__GPIO3_26	IOMUX_MODE(MX31_PIN_ATA_CS0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_ATA_CS1__GPIO3_27	IOMUX_MODE(MX31_PIN_ATA_CS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_PC_PWRON__SD2_DATA3	IOMUX_MODE(MX31_PIN_PC_PWRON, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_VS1__SD2_DATA2	IOMUX_MODE(MX31_PIN_PC_VS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_READY__SD2_DATA1	IOMUX_MODE(MX31_PIN_PC_READY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_WAIT_B__SD2_DATA0	IOMUX_MODE(MX31_PIN_PC_WAIT_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_CD2_B__SD2_CLK	IOMUX_MODE(MX31_PIN_PC_CD2_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_PC_CD1_B__SD2_CMD	IOMUX_MODE(MX31_PIN_PC_CD1_B, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_ATA_DIOR__GPIO3_28	IOMUX_MODE(MX31_PIN_ATA_DIOR, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_ATA_DIOW__GPIO3_29	IOMUX_MODE(MX31_PIN_ATA_DIOW, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_LD0__LD0		IOMUX_MODE(MX31_PIN_LD0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD1__LD1		IOMUX_MODE(MX31_PIN_LD1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD2__LD2		IOMUX_MODE(MX31_PIN_LD2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD3__LD3		IOMUX_MODE(MX31_PIN_LD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD4__LD4		IOMUX_MODE(MX31_PIN_LD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD5__LD5		IOMUX_MODE(MX31_PIN_LD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD6__LD6		IOMUX_MODE(MX31_PIN_LD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD7__LD7		IOMUX_MODE(MX31_PIN_LD7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD8__LD8		IOMUX_MODE(MX31_PIN_LD8, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD9__LD9		IOMUX_MODE(MX31_PIN_LD9, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD10__LD10		IOMUX_MODE(MX31_PIN_LD10, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD11__LD11		IOMUX_MODE(MX31_PIN_LD11, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD12__LD12		IOMUX_MODE(MX31_PIN_LD12, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD13__LD13		IOMUX_MODE(MX31_PIN_LD13, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD14__LD14		IOMUX_MODE(MX31_PIN_LD14, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD15__LD15		IOMUX_MODE(MX31_PIN_LD15, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD16__LD16		IOMUX_MODE(MX31_PIN_LD16, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_LD17__LD17		IOMUX_MODE(MX31_PIN_LD17, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_VSYNC3__VSYNC3		IOMUX_MODE(MX31_PIN_VSYNC3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_HSYNC__HSYNC		IOMUX_MODE(MX31_PIN_HSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_FPSHIFT__FPSHIFT	IOMUX_MODE(MX31_PIN_FPSHIFT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_DRDY0__DRDY0		IOMUX_MODE(MX31_PIN_DRDY0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_REV__D3_REV		IOMUX_MODE(MX31_PIN_D3_REV, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CONTRAST__CONTRAST	IOMUX_MODE(MX31_PIN_CONTRAST, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_SPL__D3_SPL		IOMUX_MODE(MX31_PIN_D3_SPL, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_D3_CLS__D3_CLS		IOMUX_MODE(MX31_PIN_D3_CLS, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO1_1__GPIO          IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DCD_DTE1__I2C2_SDA	IOMUX_MODE(MX31_PIN_DCD_DTE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_RI_DTE1__I2C2_SCL	IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_ALT2)
-#define MX31_PIN_CSPI2_SS2__I2C3_SDA	IOMUX_MODE(MX31_PIN_CSPI2_SS2, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI2_SCLK__I2C3_SCL	IOMUX_MODE(MX31_PIN_CSPI2_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSI_D4__CSI_D4		IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D5__CSI_D5		IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D6__CSI_D6		IOMUX_MODE(MX31_PIN_CSI_D6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D7__CSI_D7		IOMUX_MODE(MX31_PIN_CSI_D7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D8__CSI_D8		IOMUX_MODE(MX31_PIN_CSI_D8, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D9__CSI_D9		IOMUX_MODE(MX31_PIN_CSI_D9, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D10__CSI_D10	IOMUX_MODE(MX31_PIN_CSI_D10, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D11__CSI_D11	IOMUX_MODE(MX31_PIN_CSI_D11, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D12__CSI_D12	IOMUX_MODE(MX31_PIN_CSI_D12, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D13__CSI_D13	IOMUX_MODE(MX31_PIN_CSI_D13, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D14__CSI_D14	IOMUX_MODE(MX31_PIN_CSI_D14, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_D15__CSI_D15	IOMUX_MODE(MX31_PIN_CSI_D15, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_HSYNC__CSI_HSYNC	IOMUX_MODE(MX31_PIN_CSI_HSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_MCLK__CSI_MCLK	IOMUX_MODE(MX31_PIN_CSI_MCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_PIXCLK__CSI_PIXCLK	IOMUX_MODE(MX31_PIN_CSI_PIXCLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSI_VSYNC__CSI_VSYNC	IOMUX_MODE(MX31_PIN_CSI_VSYNC, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO3_0__GPIO3_0	IOMUX_MODE(MX31_PIN_GPIO3_0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_GPIO3_1__GPIO3_1	IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_TXD2__GPIO1_28		IOMUX_MODE(MX31_PIN_TXD2, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSI_D4__GPIO3_4	IOMUX_MODE(MX31_PIN_CSI_D4, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSI_D5__GPIO3_5	IOMUX_MODE(MX31_PIN_CSI_D5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USBOTG_DATA0__USBOTG_DATA0	IOMUX_MODE(MX31_PIN_USBOTG_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA1__USBOTG_DATA1	IOMUX_MODE(MX31_PIN_USBOTG_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA2__USBOTG_DATA2	IOMUX_MODE(MX31_PIN_USBOTG_DATA2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA3__USBOTG_DATA3	IOMUX_MODE(MX31_PIN_USBOTG_DATA3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA4__USBOTG_DATA4	IOMUX_MODE(MX31_PIN_USBOTG_DATA4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA5__USBOTG_DATA5	IOMUX_MODE(MX31_PIN_USBOTG_DATA5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA6__USBOTG_DATA6	IOMUX_MODE(MX31_PIN_USBOTG_DATA6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DATA7__USBOTG_DATA7	IOMUX_MODE(MX31_PIN_USBOTG_DATA7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_CLK__USBOTG_CLK		IOMUX_MODE(MX31_PIN_USBOTG_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_DIR__USBOTG_DIR		IOMUX_MODE(MX31_PIN_USBOTG_DIR, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_NXT__USBOTG_NXT		IOMUX_MODE(MX31_PIN_USBOTG_NXT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBOTG_STP__USBOTG_STP		IOMUX_MODE(MX31_PIN_USBOTG_STP, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_CSPI1_MOSI__USBH1_RXDM		IOMUX_MODE(MX31_PIN_CSPI1_MOSI, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_MISO__USBH1_RXDP		IOMUX_MODE(MX31_PIN_CSPI1_MISO, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS0__USBH1_TXDM		IOMUX_MODE(MX31_PIN_CSPI1_SS0, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS1__USBH1_TXDP		IOMUX_MODE(MX31_PIN_CSPI1_SS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SS2__USBH1_RCV		IOMUX_MODE(MX31_PIN_CSPI1_SS2, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SCLK__USBH1_OEB		IOMUX_MODE(MX31_PIN_CSPI1_SCLK, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_CSPI1_SPI_RDY__USBH1_FS	IOMUX_MODE(MX31_PIN_CSPI1_SPI_RDY, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_SFS6__USBH1_SUSPEND	IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_NFRE_B__GPIO1_11	IOMUX_MODE(MX31_PIN_NFRE_B, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_NFALE__GPIO1_12	IOMUX_MODE(MX31_PIN_NFALE, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USBH2_DATA0__USBH2_DATA0	IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_DATA1__USBH2_DATA1	IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD3__USBH2_DATA2	IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD3__USBH2_DATA3	IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK3__USBH2_DATA4	IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS3__USBH2_DATA5	IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD6__USBH2_DATA6	IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD6__USBH2_DATA7	IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_CLK__USBH2_CLK		IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_DIR__USBH2_DIR		IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_NXT__USBH2_NXT		IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_USBH2_STP__USBH2_STP		IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK6__GPIO1_25		IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_USB_OC__GPIO1_30	IOMUX_MODE(MX31_PIN_USB_OC, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_I2C_DAT__I2C1_SDA	IOMUX_MODE(MX31_PIN_I2C_DAT, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_I2C_CLK__I2C1_SCL	IOMUX_MODE(MX31_PIN_I2C_CLK, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_GPIO1_0__GPIO1_0	IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SVEN0__GPIO2_0		IOMUX_MODE(MX31_PIN_SVEN0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STX0__GPIO2_1		IOMUX_MODE(MX31_PIN_STX0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SRX0__GPIO2_2		IOMUX_MODE(MX31_PIN_SRX0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SIMPD0__GPIO2_3	IOMUX_MODE(MX31_PIN_SIMPD0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DTR_DCE1__GPIO2_8	IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DSR_DCE1__GPIO2_9	IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_RI_DCE1__GPIO2_10	IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_DCD_DCE1__GPIO2_11	IOMUX_MODE(MX31_PIN_DCD_DCE1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STXD5__GPIO1_21	IOMUX_MODE(MX31_PIN_STXD5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_SRXD5__GPIO1_22	IOMUX_MODE(MX31_PIN_SRXD5, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_GPIO1_3__GPIO1_3	IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CSPI2_SS1__CSPI3_SS1	IOMUX_MODE(MX31_PIN_CSPI2_SS1, IOMUX_CONFIG_ALT1)
-#define MX31_PIN_RTS1__GPIO2_6		IOMUX_MODE(MX31_PIN_RTS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_CTS1__GPIO2_7		IOMUX_MODE(MX31_PIN_CTS1, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_LCS0__GPIO3_23		IOMUX_MODE(MX31_PIN_LCS0, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_STXD4__STXD4		IOMUX_MODE(MX31_PIN_STXD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD4__SRXD4		IOMUX_MODE(MX31_PIN_SRXD4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK4__SCK4		IOMUX_MODE(MX31_PIN_SCK4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS4__SFS4		IOMUX_MODE(MX31_PIN_SFS4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_STXD5__STXD5		IOMUX_MODE(MX31_PIN_STXD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SRXD5__SRXD5		IOMUX_MODE(MX31_PIN_SRXD5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SCK5__SCK5		IOMUX_MODE(MX31_PIN_SCK5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_SFS5__SFS5		IOMUX_MODE(MX31_PIN_SFS5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW0_KEY_ROW0	IOMUX_MODE(MX31_PIN_KEY_ROW0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW1_KEY_ROW1	IOMUX_MODE(MX31_PIN_KEY_ROW1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW2_KEY_ROW2	IOMUX_MODE(MX31_PIN_KEY_ROW2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW3_KEY_ROW3	IOMUX_MODE(MX31_PIN_KEY_ROW3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW4_KEY_ROW4	IOMUX_MODE(MX31_PIN_KEY_ROW4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW4_GPIO		IOMUX_MODE(MX31_PIN_KEY_ROW4, IOMUX_CONFIG_GPIO)
-#define MX31_PIN_KEY_ROW5_KEY_ROW5	IOMUX_MODE(MX31_PIN_KEY_ROW5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW6_KEY_ROW6	IOMUX_MODE(MX31_PIN_KEY_ROW6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_ROW7_KEY_ROW7	IOMUX_MODE(MX31_PIN_KEY_ROW7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL0_KEY_COL0	IOMUX_MODE(MX31_PIN_KEY_COL0, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL1_KEY_COL1	IOMUX_MODE(MX31_PIN_KEY_COL1, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL2_KEY_COL2	IOMUX_MODE(MX31_PIN_KEY_COL2, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL3_KEY_COL3	IOMUX_MODE(MX31_PIN_KEY_COL3, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL4_KEY_COL4	IOMUX_MODE(MX31_PIN_KEY_COL4, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL5_KEY_COL5	IOMUX_MODE(MX31_PIN_KEY_COL5, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL6_KEY_COL6	IOMUX_MODE(MX31_PIN_KEY_COL6, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_KEY_COL7_KEY_COL7	IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_FUNC)
-#define MX31_PIN_WATCHDOG_RST__WATCHDOG_RST	IOMUX_MODE(MX31_PIN_WATCHDOG_RST, IOMUX_CONFIG_FUNC)
-
-
-/*
- * XXX: The SS0, SS1, SS2, SS3 lines of spi3 are multiplexed with cspi2_ss0,
- * cspi2_ss1, cspi1_ss0 cspi1_ss1
- */
-
-/*
- * This function configures the pad value for a IOMUX pin.
- */
-void mxc_iomux_set_pad(enum iomux_pins, u32);
-
-#endif /* ifndef __MACH_IOMUX_MX3_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx35.h b/arch/arm/mach-imx/iomux-mx35.h
deleted file mode 100644
index 7fb5259b3ee0..000000000000
--- a/arch/arm/mach-imx/iomux-mx35.h
+++ /dev/null
@@ -1,1254 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH <armlinux@phytec.de>
- */
-
-#ifndef __MACH_IOMUX_MX35_H__
-#define __MACH_IOMUX_MX35_H__
-
-#include "iomux-v3.h"
-
-/*
- * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode>
- * If <padname> or <padmode> refers to a GPIO, it is named
- * GPIO_<unit>_<num> see also iomux-v3.h
- */
-
-/*									  PAD    MUX   ALT INPSE PATH */
-#define MX35_PAD_CAPTURE__GPT_CAPIN1				IOMUX_PAD(0x328, 0x004, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__GPT_CMPOUT2				IOMUX_PAD(0x328, 0x004, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__CSPI2_SS1				IOMUX_PAD(0x328, 0x004, 2, 0x7f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__EPIT1_EPITO				IOMUX_PAD(0x328, 0x004, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__CCM_CLK32K				IOMUX_PAD(0x328, 0x004, 4, 0x7d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_CAPTURE__GPIO1_4				IOMUX_PAD(0x328, 0x004, 5, 0x850, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_COMPARE__GPT_CMPOUT1				IOMUX_PAD(0x32c, 0x008, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPT_CAPIN2				IOMUX_PAD(0x32c, 0x008, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPT_CMPOUT3				IOMUX_PAD(0x32c, 0x008, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__EPIT2_EPITO				IOMUX_PAD(0x32c, 0x008, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__GPIO1_5				IOMUX_PAD(0x32c, 0x008, 5, 0x854, 0, NO_PAD_CTRL)
-#define MX35_PAD_COMPARE__SDMA_EXTDMA_2				IOMUX_PAD(0x32c, 0x008, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_WDOG_RST__WDOG_WDOG_B				IOMUX_PAD(0x330, 0x00c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_WDOG_RST__IPU_FLASH_STROBE			IOMUX_PAD(0x330, 0x00c, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_WDOG_RST__GPIO1_6				IOMUX_PAD(0x330, 0x00c, 5, 0x858, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO1_0__GPIO1_0				IOMUX_PAD(0x334, 0x010, 0, 0x82c, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__CCM_PMIC_RDY				IOMUX_PAD(0x334, 0x010, 1, 0x7d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__OWIRE_LINE				IOMUX_PAD(0x334, 0x010, 2, 0x990, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_0__SDMA_EXTDMA_0				IOMUX_PAD(0x334, 0x010, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO1_1__GPIO1_1				IOMUX_PAD(0x338, 0x014, 0, 0x838, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__PWM_PWMO				IOMUX_PAD(0x338, 0x014, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__CSPI1_SS2				IOMUX_PAD(0x338, 0x014, 3, 0x7d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__SCC_TAMPER_DETECT			IOMUX_PAD(0x338, 0x014, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO1_1__SDMA_EXTDMA_1				IOMUX_PAD(0x338, 0x014, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO2_0__GPIO2_0				IOMUX_PAD(0x33c, 0x018, 0, 0x868, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO2_0__USB_TOP_USBOTG_CLK			IOMUX_PAD(0x33c, 0x018, 1, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_GPIO3_0__GPIO3_0				IOMUX_PAD(0x340, 0x01c, 0, 0x8e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_GPIO3_0__USB_TOP_USBH2_CLK			IOMUX_PAD(0x340, 0x01c, 1, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RESET_IN_B__CCM_RESET_IN_B			IOMUX_PAD(0x344, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_POR_B__CCM_POR_B				IOMUX_PAD(0x348, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLKO__CCM_CLKO					IOMUX_PAD(0x34c, 0x020, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CLKO__GPIO1_8					IOMUX_PAD(0x34c, 0x020, 5, 0x860, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_BOOT_MODE0__CCM_BOOT_MODE_0			IOMUX_PAD(0x350, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_BOOT_MODE1__CCM_BOOT_MODE_1			IOMUX_PAD(0x354, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLK_MODE0__CCM_CLK_MODE_0			IOMUX_PAD(0x358, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CLK_MODE1__CCM_CLK_MODE_1			IOMUX_PAD(0x35c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_POWER_FAIL__CCM_DSM_WAKEUP_INT_26		IOMUX_PAD(0x360, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_VSTBY__CCM_VSTBY				IOMUX_PAD(0x364, 0x024, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_VSTBY__GPIO1_7					IOMUX_PAD(0x364, 0x024, 5, 0x85c, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_A0__EMI_EIM_DA_L_0				IOMUX_PAD(0x368, 0x028, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A1__EMI_EIM_DA_L_1				IOMUX_PAD(0x36c, 0x02c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A2__EMI_EIM_DA_L_2				IOMUX_PAD(0x370, 0x030, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A3__EMI_EIM_DA_L_3				IOMUX_PAD(0x374, 0x034, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A4__EMI_EIM_DA_L_4				IOMUX_PAD(0x378, 0x038, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A5__EMI_EIM_DA_L_5				IOMUX_PAD(0x37c, 0x03c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A6__EMI_EIM_DA_L_6				IOMUX_PAD(0x380, 0x040, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A7__EMI_EIM_DA_L_7				IOMUX_PAD(0x384, 0x044, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A8__EMI_EIM_DA_H_8				IOMUX_PAD(0x388, 0x048, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A9__EMI_EIM_DA_H_9				IOMUX_PAD(0x38c, 0x04c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A10__EMI_EIM_DA_H_10				IOMUX_PAD(0x390, 0x050, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_MA10__EMI_MA10					IOMUX_PAD(0x394, 0x054, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A11__EMI_EIM_DA_H_11				IOMUX_PAD(0x398, 0x058, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A12__EMI_EIM_DA_H_12				IOMUX_PAD(0x39c, 0x05c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A13__EMI_EIM_DA_H_13				IOMUX_PAD(0x3a0, 0x060, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A14__EMI_EIM_DA_H2_14				IOMUX_PAD(0x3a4, 0x064, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A15__EMI_EIM_DA_H2_15				IOMUX_PAD(0x3a8, 0x068, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A16__EMI_EIM_A_16				IOMUX_PAD(0x3ac, 0x06c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A17__EMI_EIM_A_17				IOMUX_PAD(0x3b0, 0x070, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A18__EMI_EIM_A_18				IOMUX_PAD(0x3b4, 0x074, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A19__EMI_EIM_A_19				IOMUX_PAD(0x3b8, 0x078, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A20__EMI_EIM_A_20				IOMUX_PAD(0x3bc, 0x07c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A21__EMI_EIM_A_21				IOMUX_PAD(0x3c0, 0x080, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A22__EMI_EIM_A_22				IOMUX_PAD(0x3c4, 0x084, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A23__EMI_EIM_A_23				IOMUX_PAD(0x3c8, 0x088, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A24__EMI_EIM_A_24				IOMUX_PAD(0x3cc, 0x08c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_A25__EMI_EIM_A_25				IOMUX_PAD(0x3d0, 0x090, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDBA1__EMI_EIM_SDBA1				IOMUX_PAD(0x3d4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDBA0__EMI_EIM_SDBA0				IOMUX_PAD(0x3d8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD0__EMI_DRAM_D_0				IOMUX_PAD(0x3dc, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1__EMI_DRAM_D_1				IOMUX_PAD(0x3e0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2__EMI_DRAM_D_2				IOMUX_PAD(0x3e4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD3__EMI_DRAM_D_3				IOMUX_PAD(0x3e8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD4__EMI_DRAM_D_4				IOMUX_PAD(0x3ec, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD5__EMI_DRAM_D_5				IOMUX_PAD(0x3f0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD6__EMI_DRAM_D_6				IOMUX_PAD(0x3f4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD7__EMI_DRAM_D_7				IOMUX_PAD(0x3f8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD8__EMI_DRAM_D_8				IOMUX_PAD(0x3fc, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD9__EMI_DRAM_D_9				IOMUX_PAD(0x400, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD10__EMI_DRAM_D_10				IOMUX_PAD(0x404, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD11__EMI_DRAM_D_11				IOMUX_PAD(0x408, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD12__EMI_DRAM_D_12				IOMUX_PAD(0x40c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD13__EMI_DRAM_D_13				IOMUX_PAD(0x410, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD14__EMI_DRAM_D_14				IOMUX_PAD(0x414, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD15__EMI_DRAM_D_15				IOMUX_PAD(0x418, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD16__EMI_DRAM_D_16				IOMUX_PAD(0x41c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD17__EMI_DRAM_D_17				IOMUX_PAD(0x420, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD18__EMI_DRAM_D_18				IOMUX_PAD(0x424, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD19__EMI_DRAM_D_19				IOMUX_PAD(0x428, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD20__EMI_DRAM_D_20				IOMUX_PAD(0x42c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD21__EMI_DRAM_D_21				IOMUX_PAD(0x430, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD22__EMI_DRAM_D_22				IOMUX_PAD(0x434, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD23__EMI_DRAM_D_23				IOMUX_PAD(0x438, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD24__EMI_DRAM_D_24				IOMUX_PAD(0x43c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD25__EMI_DRAM_D_25				IOMUX_PAD(0x440, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD26__EMI_DRAM_D_26				IOMUX_PAD(0x444, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD27__EMI_DRAM_D_27				IOMUX_PAD(0x448, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD28__EMI_DRAM_D_28				IOMUX_PAD(0x44c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD29__EMI_DRAM_D_29				IOMUX_PAD(0x450, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD30__EMI_DRAM_D_30				IOMUX_PAD(0x454, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD31__EMI_DRAM_D_31				IOMUX_PAD(0x458, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM0__EMI_DRAM_DQM_0				IOMUX_PAD(0x45c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM1__EMI_DRAM_DQM_1				IOMUX_PAD(0x460, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM2__EMI_DRAM_DQM_2				IOMUX_PAD(0x464, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_DQM3__EMI_DRAM_DQM_3				IOMUX_PAD(0x468, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_EB0__EMI_EIM_EB0_B				IOMUX_PAD(0x46c, 0x094, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_EB1__EMI_EIM_EB1_B				IOMUX_PAD(0x470, 0x098, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_OE__EMI_EIM_OE					IOMUX_PAD(0x474, 0x09c, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS0__EMI_EIM_CS0				IOMUX_PAD(0x478, 0x0a0, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS1__EMI_EIM_CS1				IOMUX_PAD(0x47c, 0x0a4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CS1__EMI_NANDF_CE3				IOMUX_PAD(0x47c, 0x0a4, 3, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS2__EMI_EIM_CS2				IOMUX_PAD(0x480, 0x0a8, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS3__EMI_EIM_CS3				IOMUX_PAD(0x484, 0x0ac, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS4__EMI_EIM_CS4				IOMUX_PAD(0x488, 0x0b0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__EMI_DTACK_B				IOMUX_PAD(0x488, 0x0b0, 1, 0x800, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__EMI_NANDF_CE1				IOMUX_PAD(0x488, 0x0b0, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CS4__GPIO1_20					IOMUX_PAD(0x488, 0x0b0, 5, 0x83c, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CS5__EMI_EIM_CS5				IOMUX_PAD(0x48c, 0x0b4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__CSPI2_SS2					IOMUX_PAD(0x48c, 0x0b4, 1, 0x7f8, 0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__CSPI1_SS2					IOMUX_PAD(0x48c, 0x0b4, 2, 0x7d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_CS5__EMI_NANDF_CE2				IOMUX_PAD(0x48c, 0x0b4, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CS5__GPIO1_21					IOMUX_PAD(0x48c, 0x0b4, 5, 0x840, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_NF_CE0__EMI_NANDF_CE0				IOMUX_PAD(0x490, 0x0b8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NF_CE0__GPIO1_22				IOMUX_PAD(0x490, 0x0b8, 5, 0x844, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_ECB__EMI_EIM_ECB				IOMUX_PAD(0x494, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LBA__EMI_EIM_LBA				IOMUX_PAD(0x498, 0x0bc, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_BCLK__EMI_EIM_BCLK				IOMUX_PAD(0x49c, 0x0c0, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RW__EMI_EIM_RW					IOMUX_PAD(0x4a0, 0x0c4, 0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RAS__EMI_DRAM_RAS				IOMUX_PAD(0x4a4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CAS__EMI_DRAM_CAS				IOMUX_PAD(0x4a8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDWE__EMI_DRAM_SDWE				IOMUX_PAD(0x4ac, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCKE0__EMI_DRAM_SDCKE_0			IOMUX_PAD(0x4b0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCKE1__EMI_DRAM_SDCKE_1			IOMUX_PAD(0x4b4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDCLK__EMI_DRAM_SDCLK				IOMUX_PAD(0x4b8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS0__EMI_DRAM_SDQS_0				IOMUX_PAD(0x4bc, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS1__EMI_DRAM_SDQS_1				IOMUX_PAD(0x4c0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS2__EMI_DRAM_SDQS_2				IOMUX_PAD(0x4c4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SDQS3__EMI_DRAM_SDQS_3				IOMUX_PAD(0x4c8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFWE_B__EMI_NANDF_WE_B				IOMUX_PAD(0x4cc, 0x0c8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__USB_TOP_USBH2_DATA_3			IOMUX_PAD(0x4cc, 0x0c8, 1, 0x9d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__IPU_DISPB_D0_VSYNC			IOMUX_PAD(0x4cc, 0x0c8, 2, 0x924, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__GPIO2_18				IOMUX_PAD(0x4cc, 0x0c8, 5, 0x88c, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWE_B__ARM11P_TOP_TRACE_0			IOMUX_PAD(0x4cc, 0x0c8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFRE_B__EMI_NANDF_RE_B				IOMUX_PAD(0x4d0, 0x0cc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__USB_TOP_USBH2_DIR			IOMUX_PAD(0x4d0, 0x0cc, 1, 0x9ec, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__IPU_DISPB_BCLK				IOMUX_PAD(0x4d0, 0x0cc, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__GPIO2_19				IOMUX_PAD(0x4d0, 0x0cc, 5, 0x890, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRE_B__ARM11P_TOP_TRACE_1			IOMUX_PAD(0x4d0, 0x0cc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFALE__EMI_NANDF_ALE				IOMUX_PAD(0x4d4, 0x0d0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__USB_TOP_USBH2_STP			IOMUX_PAD(0x4d4, 0x0d0, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__IPU_DISPB_CS0				IOMUX_PAD(0x4d4, 0x0d0, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__GPIO2_20				IOMUX_PAD(0x4d4, 0x0d0, 5, 0x898, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFALE__ARM11P_TOP_TRACE_2			IOMUX_PAD(0x4d4, 0x0d0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFCLE__EMI_NANDF_CLE				IOMUX_PAD(0x4d8, 0x0d4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__USB_TOP_USBH2_NXT			IOMUX_PAD(0x4d8, 0x0d4, 1, 0x9f0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__IPU_DISPB_PAR_RS			IOMUX_PAD(0x4d8, 0x0d4, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__GPIO2_21				IOMUX_PAD(0x4d8, 0x0d4, 5, 0x89c, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFCLE__ARM11P_TOP_TRACE_3			IOMUX_PAD(0x4d8, 0x0d4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFWP_B__EMI_NANDF_WP_B				IOMUX_PAD(0x4dc, 0x0d8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__USB_TOP_USBH2_DATA_7			IOMUX_PAD(0x4dc, 0x0d8, 1, 0x9e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__IPU_DISPB_WR				IOMUX_PAD(0x4dc, 0x0d8, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__GPIO2_22				IOMUX_PAD(0x4dc, 0x0d8, 5, 0x8a0, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFWP_B__ARM11P_TOP_TRCTL			IOMUX_PAD(0x4dc, 0x0d8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_NFRB__EMI_NANDF_RB				IOMUX_PAD(0x4e0, 0x0dc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__IPU_DISPB_RD				IOMUX_PAD(0x4e0, 0x0dc, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__GPIO2_23					IOMUX_PAD(0x4e0, 0x0dc, 5, 0x8a4, 0, NO_PAD_CTRL)
-#define MX35_PAD_NFRB__ARM11P_TOP_TRCLK				IOMUX_PAD(0x4e0, 0x0dc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D15__EMI_EIM_D_15				IOMUX_PAD(0x4e4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D14__EMI_EIM_D_14				IOMUX_PAD(0x4e8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D13__EMI_EIM_D_13				IOMUX_PAD(0x4ec, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D12__EMI_EIM_D_12				IOMUX_PAD(0x4f0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D11__EMI_EIM_D_11				IOMUX_PAD(0x4f4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D10__EMI_EIM_D_10				IOMUX_PAD(0x4f8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D9__EMI_EIM_D_9				IOMUX_PAD(0x4fc, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D8__EMI_EIM_D_8				IOMUX_PAD(0x500, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D7__EMI_EIM_D_7				IOMUX_PAD(0x504, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D6__EMI_EIM_D_6				IOMUX_PAD(0x508, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D5__EMI_EIM_D_5				IOMUX_PAD(0x50c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D4__EMI_EIM_D_4				IOMUX_PAD(0x510, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3__EMI_EIM_D_3				IOMUX_PAD(0x514, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D2__EMI_EIM_D_2				IOMUX_PAD(0x518, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D1__EMI_EIM_D_1				IOMUX_PAD(0x51c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D0__EMI_EIM_D_0				IOMUX_PAD(0x520, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D8__IPU_CSI_D_8				IOMUX_PAD(0x524, 0x0e0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__KPP_COL_0				IOMUX_PAD(0x524, 0x0e0, 1, 0x950, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__GPIO1_20				IOMUX_PAD(0x524, 0x0e0, 5, 0x83c, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D8__ARM11P_TOP_EVNTBUS_13			IOMUX_PAD(0x524, 0x0e0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D9__IPU_CSI_D_9				IOMUX_PAD(0x528, 0x0e4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__KPP_COL_1				IOMUX_PAD(0x528, 0x0e4, 1, 0x954, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__GPIO1_21				IOMUX_PAD(0x528, 0x0e4, 5, 0x840, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D9__ARM11P_TOP_EVNTBUS_14			IOMUX_PAD(0x528, 0x0e4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D10__IPU_CSI_D_10				IOMUX_PAD(0x52c, 0x0e8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__KPP_COL_2				IOMUX_PAD(0x52c, 0x0e8, 1, 0x958, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__GPIO1_22				IOMUX_PAD(0x52c, 0x0e8, 5, 0x844, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D10__ARM11P_TOP_EVNTBUS_15			IOMUX_PAD(0x52c, 0x0e8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D11__IPU_CSI_D_11				IOMUX_PAD(0x530, 0x0ec, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D11__KPP_COL_3				IOMUX_PAD(0x530, 0x0ec, 1, 0x95c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D11__GPIO1_23				IOMUX_PAD(0x530, 0x0ec, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D12__IPU_CSI_D_12				IOMUX_PAD(0x534, 0x0f0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D12__KPP_ROW_0				IOMUX_PAD(0x534, 0x0f0, 1, 0x970, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D12__GPIO1_24				IOMUX_PAD(0x534, 0x0f0, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D13__IPU_CSI_D_13				IOMUX_PAD(0x538, 0x0f4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D13__KPP_ROW_1				IOMUX_PAD(0x538, 0x0f4, 1, 0x974, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D13__GPIO1_25				IOMUX_PAD(0x538, 0x0f4, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D14__IPU_CSI_D_14				IOMUX_PAD(0x53c, 0x0f8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D14__KPP_ROW_2				IOMUX_PAD(0x53c, 0x0f8, 1, 0x978, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D14__GPIO1_26				IOMUX_PAD(0x53c, 0x0f8, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_D15__IPU_CSI_D_15				IOMUX_PAD(0x540, 0x0fc, 0, 0x97c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D15__KPP_ROW_3				IOMUX_PAD(0x540, 0x0fc, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_D15__GPIO1_27				IOMUX_PAD(0x540, 0x0fc, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_MCLK__IPU_CSI_MCLK				IOMUX_PAD(0x544, 0x100, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_MCLK__GPIO1_28				IOMUX_PAD(0x544, 0x100, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_VSYNC__IPU_CSI_VSYNC			IOMUX_PAD(0x548, 0x104, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_VSYNC__GPIO1_29				IOMUX_PAD(0x548, 0x104, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_HSYNC__IPU_CSI_HSYNC			IOMUX_PAD(0x54c, 0x108, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_HSYNC__GPIO1_30				IOMUX_PAD(0x54c, 0x108, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSI_PIXCLK__IPU_CSI_PIXCLK			IOMUX_PAD(0x550, 0x10c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSI_PIXCLK__GPIO1_31				IOMUX_PAD(0x550, 0x10c, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C1_CLK__I2C1_SCL				IOMUX_PAD(0x554, 0x110, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_CLK__GPIO2_24				IOMUX_PAD(0x554, 0x110, 5, 0x8a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_CLK__CCM_USB_BYP_CLK			IOMUX_PAD(0x554, 0x110, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C1_DAT__I2C1_SDA				IOMUX_PAD(0x558, 0x114, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C1_DAT__GPIO2_25				IOMUX_PAD(0x558, 0x114, 5, 0x8ac, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C2_CLK__I2C2_SCL				IOMUX_PAD(0x55c, 0x118, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__CAN1_TXCAN				IOMUX_PAD(0x55c, 0x118, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR			IOMUX_PAD(0x55c, 0x118, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__GPIO2_26				IOMUX_PAD(0x55c, 0x118, 5, 0x8b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_CLK__SDMA_DEBUG_BUS_DEVICE_2		IOMUX_PAD(0x55c, 0x118, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_I2C2_DAT__I2C2_SDA				IOMUX_PAD(0x560, 0x11c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__CAN1_RXCAN				IOMUX_PAD(0x560, 0x11c, 1, 0x7c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC			IOMUX_PAD(0x560, 0x11c, 2, 0x9f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__GPIO2_27				IOMUX_PAD(0x560, 0x11c, 5, 0x8b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_I2C2_DAT__SDMA_DEBUG_BUS_DEVICE_3		IOMUX_PAD(0x560, 0x11c, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXD4__AUDMUX_AUD4_TXD				IOMUX_PAD(0x564, 0x120, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_STXD4__GPIO2_28				IOMUX_PAD(0x564, 0x120, 5, 0x8b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD4__ARM11P_TOP_ARM_COREASID0		IOMUX_PAD(0x564, 0x120, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SRXD4__AUDMUX_AUD4_RXD				IOMUX_PAD(0x568, 0x124, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD4__GPIO2_29				IOMUX_PAD(0x568, 0x124, 5, 0x8bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD4__ARM11P_TOP_ARM_COREASID1		IOMUX_PAD(0x568, 0x124, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCK4__AUDMUX_AUD4_TXC				IOMUX_PAD(0x56c, 0x128, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SCK4__GPIO2_30					IOMUX_PAD(0x56c, 0x128, 5, 0x8c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK4__ARM11P_TOP_ARM_COREASID2			IOMUX_PAD(0x56c, 0x128, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS			IOMUX_PAD(0x570, 0x12c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS4__GPIO2_31				IOMUX_PAD(0x570, 0x12c, 5, 0x8c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS4__ARM11P_TOP_ARM_COREASID3		IOMUX_PAD(0x570, 0x12c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXD5__AUDMUX_AUD5_TXD				IOMUX_PAD(0x574, 0x130, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__SPDIF_SPDIF_OUT1			IOMUX_PAD(0x574, 0x130, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__CSPI2_MOSI				IOMUX_PAD(0x574, 0x130, 2, 0x7ec, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__GPIO1_0					IOMUX_PAD(0x574, 0x130, 5, 0x82c, 1, NO_PAD_CTRL)
-#define MX35_PAD_STXD5__ARM11P_TOP_ARM_COREASID4		IOMUX_PAD(0x574, 0x130, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SRXD5__AUDMUX_AUD5_RXD				IOMUX_PAD(0x578, 0x134, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__SPDIF_SPDIF_IN1				IOMUX_PAD(0x578, 0x134, 1, 0x998, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__CSPI2_MISO				IOMUX_PAD(0x578, 0x134, 2, 0x7e8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__GPIO1_1					IOMUX_PAD(0x578, 0x134, 5, 0x838, 1, NO_PAD_CTRL)
-#define MX35_PAD_SRXD5__ARM11P_TOP_ARM_COREASID5		IOMUX_PAD(0x578, 0x134, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCK5__AUDMUX_AUD5_TXC				IOMUX_PAD(0x57c, 0x138, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__SPDIF_SPDIF_EXTCLK			IOMUX_PAD(0x57c, 0x138, 1, 0x994, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__CSPI2_SCLK				IOMUX_PAD(0x57c, 0x138, 2, 0x7e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__GPIO1_2					IOMUX_PAD(0x57c, 0x138, 5, 0x848, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCK5__ARM11P_TOP_ARM_COREASID6			IOMUX_PAD(0x57c, 0x138, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_STXFS5__AUDMUX_AUD5_TXFS			IOMUX_PAD(0x580, 0x13c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__CSPI2_RDY				IOMUX_PAD(0x580, 0x13c, 2, 0x7e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__GPIO1_3				IOMUX_PAD(0x580, 0x13c, 5, 0x84c, 0, NO_PAD_CTRL)
-#define MX35_PAD_STXFS5__ARM11P_TOP_ARM_COREASID7		IOMUX_PAD(0x580, 0x13c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCKR__ESAI_SCKR				IOMUX_PAD(0x584, 0x140, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SCKR__GPIO1_4					IOMUX_PAD(0x584, 0x140, 5, 0x850, 1, NO_PAD_CTRL)
-#define MX35_PAD_SCKR__ARM11P_TOP_EVNTBUS_10			IOMUX_PAD(0x584, 0x140, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FSR__ESAI_FSR					IOMUX_PAD(0x588, 0x144, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FSR__GPIO1_5					IOMUX_PAD(0x588, 0x144, 5, 0x854, 1, NO_PAD_CTRL)
-#define MX35_PAD_FSR__ARM11P_TOP_EVNTBUS_11			IOMUX_PAD(0x588, 0x144, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_HCKR__ESAI_HCKR				IOMUX_PAD(0x58c, 0x148, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__AUDMUX_AUD5_RXFS				IOMUX_PAD(0x58c, 0x148, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__CSPI2_SS0				IOMUX_PAD(0x58c, 0x148, 2, 0x7f0, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__IPU_FLASH_STROBE				IOMUX_PAD(0x58c, 0x148, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__GPIO1_6					IOMUX_PAD(0x58c, 0x148, 5, 0x858, 1, NO_PAD_CTRL)
-#define MX35_PAD_HCKR__ARM11P_TOP_EVNTBUS_12			IOMUX_PAD(0x58c, 0x148, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SCKT__ESAI_SCKT				IOMUX_PAD(0x590, 0x14c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__GPIO1_7					IOMUX_PAD(0x590, 0x14c, 5, 0x85c, 1, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__IPU_CSI_D_0				IOMUX_PAD(0x590, 0x14c, 6, 0x930, 0, NO_PAD_CTRL)
-#define MX35_PAD_SCKT__KPP_ROW_2				IOMUX_PAD(0x590, 0x14c, 7, 0x978, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_FST__ESAI_FST					IOMUX_PAD(0x594, 0x150, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FST__GPIO1_8					IOMUX_PAD(0x594, 0x150, 5, 0x860, 1, NO_PAD_CTRL)
-#define MX35_PAD_FST__IPU_CSI_D_1				IOMUX_PAD(0x594, 0x150, 6, 0x934, 0, NO_PAD_CTRL)
-#define MX35_PAD_FST__KPP_ROW_3					IOMUX_PAD(0x594, 0x150, 7, 0x97c, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_HCKT__ESAI_HCKT				IOMUX_PAD(0x598, 0x154, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__AUDMUX_AUD5_RXC				IOMUX_PAD(0x598, 0x154, 1, 0x7a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__GPIO1_9					IOMUX_PAD(0x598, 0x154, 5, 0x864, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__IPU_CSI_D_2				IOMUX_PAD(0x598, 0x154, 6, 0x938, 0, NO_PAD_CTRL)
-#define MX35_PAD_HCKT__KPP_COL_3				IOMUX_PAD(0x598, 0x154, 7, 0x95c, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX5_RX0__ESAI_TX5_RX0				IOMUX_PAD(0x59c, 0x158, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__AUDMUX_AUD4_RXC			IOMUX_PAD(0x59c, 0x158, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__CSPI2_SS2				IOMUX_PAD(0x59c, 0x158, 2, 0x7f8, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__CAN2_TXCAN				IOMUX_PAD(0x59c, 0x158, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__UART2_DTR				IOMUX_PAD(0x59c, 0x158, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__GPIO1_10				IOMUX_PAD(0x59c, 0x158, 5, 0x830, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX5_RX0__EMI_M3IF_CHOSEN_MASTER_0		IOMUX_PAD(0x59c, 0x158, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TX4_RX1__ESAI_TX4_RX1				IOMUX_PAD(0x5a0, 0x15c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__AUDMUX_AUD4_RXFS			IOMUX_PAD(0x5a0, 0x15c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__CSPI2_SS3				IOMUX_PAD(0x5a0, 0x15c, 2, 0x7fc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__CAN2_RXCAN				IOMUX_PAD(0x5a0, 0x15c, 3, 0x7cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__UART2_DSR				IOMUX_PAD(0x5a0, 0x15c, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__GPIO1_11				IOMUX_PAD(0x5a0, 0x15c, 5, 0x834, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__IPU_CSI_D_3				IOMUX_PAD(0x5a0, 0x15c, 6, 0x93c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX4_RX1__KPP_ROW_0				IOMUX_PAD(0x5a0, 0x15c, 7, 0x970, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX3_RX2__ESAI_TX3_RX2				IOMUX_PAD(0x5a4, 0x160, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__I2C3_SCL				IOMUX_PAD(0x5a4, 0x160, 1, 0x91c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__EMI_NANDF_CE1				IOMUX_PAD(0x5a4, 0x160, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__GPIO1_12				IOMUX_PAD(0x5a4, 0x160, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__IPU_CSI_D_4				IOMUX_PAD(0x5a4, 0x160, 6, 0x940, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX3_RX2__KPP_ROW_1				IOMUX_PAD(0x5a4, 0x160, 7, 0x974, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX2_RX3__ESAI_TX2_RX3				IOMUX_PAD(0x5a8, 0x164, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__I2C3_SDA				IOMUX_PAD(0x5a8, 0x164, 1, 0x920, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__EMI_NANDF_CE2				IOMUX_PAD(0x5a8, 0x164, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__GPIO1_13				IOMUX_PAD(0x5a8, 0x164, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__IPU_CSI_D_5				IOMUX_PAD(0x5a8, 0x164, 6, 0x944, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX2_RX3__KPP_COL_0				IOMUX_PAD(0x5a8, 0x164, 7, 0x950, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX1__ESAI_TX1					IOMUX_PAD(0x5ac, 0x168, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__CCM_PMIC_RDY				IOMUX_PAD(0x5ac, 0x168, 1, 0x7d4, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX1__CSPI1_SS2					IOMUX_PAD(0x5ac, 0x168, 2, 0x7d8, 2, NO_PAD_CTRL)
-#define MX35_PAD_TX1__EMI_NANDF_CE3				IOMUX_PAD(0x5ac, 0x168, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__UART2_RI					IOMUX_PAD(0x5ac, 0x168, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__GPIO1_14					IOMUX_PAD(0x5ac, 0x168, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__IPU_CSI_D_6				IOMUX_PAD(0x5ac, 0x168, 6, 0x948, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX1__KPP_COL_1					IOMUX_PAD(0x5ac, 0x168, 7, 0x954, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_TX0__ESAI_TX0					IOMUX_PAD(0x5b0, 0x16c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__SPDIF_SPDIF_EXTCLK			IOMUX_PAD(0x5b0, 0x16c, 1, 0x994, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX0__CSPI1_SS3					IOMUX_PAD(0x5b0, 0x16c, 2, 0x7dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__EMI_DTACK_B				IOMUX_PAD(0x5b0, 0x16c, 3, 0x800, 1, NO_PAD_CTRL)
-#define MX35_PAD_TX0__UART2_DCD					IOMUX_PAD(0x5b0, 0x16c, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__GPIO1_15					IOMUX_PAD(0x5b0, 0x16c, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__IPU_CSI_D_7				IOMUX_PAD(0x5b0, 0x16c, 6, 0x94c, 0, NO_PAD_CTRL)
-#define MX35_PAD_TX0__KPP_COL_2					IOMUX_PAD(0x5b0, 0x16c, 7, 0x958, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_MOSI__CSPI1_MOSI				IOMUX_PAD(0x5b4, 0x170, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MOSI__GPIO1_16				IOMUX_PAD(0x5b4, 0x170, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MOSI__ECT_CTI_TRIG_OUT1_2		IOMUX_PAD(0x5b4, 0x170, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_MISO__CSPI1_MISO				IOMUX_PAD(0x5b8, 0x174, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MISO__GPIO1_17				IOMUX_PAD(0x5b8, 0x174, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_MISO__ECT_CTI_TRIG_OUT1_3		IOMUX_PAD(0x5b8, 0x174, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SS0__CSPI1_SS0				IOMUX_PAD(0x5bc, 0x178, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__OWIRE_LINE				IOMUX_PAD(0x5bc, 0x178, 1, 0x990, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__CSPI2_SS3				IOMUX_PAD(0x5bc, 0x178, 2, 0x7fc, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__GPIO1_18				IOMUX_PAD(0x5bc, 0x178, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS0__ECT_CTI_TRIG_OUT1_4			IOMUX_PAD(0x5bc, 0x178, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SS1__CSPI1_SS1				IOMUX_PAD(0x5c0, 0x17c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__PWM_PWMO				IOMUX_PAD(0x5c0, 0x17c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__CCM_CLK32K				IOMUX_PAD(0x5c0, 0x17c, 2, 0x7d0, 1, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__GPIO1_19				IOMUX_PAD(0x5c0, 0x17c, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__IPU_DIAGB_29			IOMUX_PAD(0x5c0, 0x17c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SS1__ECT_CTI_TRIG_OUT1_5			IOMUX_PAD(0x5c0, 0x17c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SCLK__CSPI1_SCLK				IOMUX_PAD(0x5c4, 0x180, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__GPIO3_4				IOMUX_PAD(0x5c4, 0x180, 5, 0x904, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__IPU_DIAGB_30			IOMUX_PAD(0x5c4, 0x180, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SCLK__EMI_M3IF_CHOSEN_MASTER_1		IOMUX_PAD(0x5c4, 0x180, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CSPI1_SPI_RDY__CSPI1_RDY			IOMUX_PAD(0x5c8, 0x184, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__GPIO3_5				IOMUX_PAD(0x5c8, 0x184, 5, 0x908, 0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__IPU_DIAGB_31			IOMUX_PAD(0x5c8, 0x184, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CSPI1_SPI_RDY__EMI_M3IF_CHOSEN_MASTER_2	IOMUX_PAD(0x5c8, 0x184, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RXD1__UART1_RXD_MUX				IOMUX_PAD(0x5cc, 0x188, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__CSPI2_MOSI				IOMUX_PAD(0x5cc, 0x188, 1, 0x7ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__KPP_COL_4				IOMUX_PAD(0x5cc, 0x188, 4, 0x960, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__GPIO3_6					IOMUX_PAD(0x5cc, 0x188, 5, 0x90c, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD1__ARM11P_TOP_EVNTBUS_16			IOMUX_PAD(0x5cc, 0x188, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TXD1__UART1_TXD_MUX				IOMUX_PAD(0x5d0, 0x18c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__CSPI2_MISO				IOMUX_PAD(0x5d0, 0x18c, 1, 0x7e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__KPP_COL_5				IOMUX_PAD(0x5d0, 0x18c, 4, 0x964, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__GPIO3_7					IOMUX_PAD(0x5d0, 0x18c, 5, 0x910, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD1__ARM11P_TOP_EVNTBUS_17			IOMUX_PAD(0x5d0, 0x18c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTS1__UART1_RTS				IOMUX_PAD(0x5d4, 0x190, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__CSPI2_SCLK				IOMUX_PAD(0x5d4, 0x190, 1, 0x7e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__I2C3_SCL					IOMUX_PAD(0x5d4, 0x190, 2, 0x91c, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__IPU_CSI_D_0				IOMUX_PAD(0x5d4, 0x190, 3, 0x930, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__KPP_COL_6				IOMUX_PAD(0x5d4, 0x190, 4, 0x968, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__GPIO3_8					IOMUX_PAD(0x5d4, 0x190, 5, 0x914, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__EMI_NANDF_CE1				IOMUX_PAD(0x5d4, 0x190, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RTS1__ARM11P_TOP_EVNTBUS_18			IOMUX_PAD(0x5d4, 0x190, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CTS1__UART1_CTS				IOMUX_PAD(0x5d8, 0x194, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__CSPI2_RDY				IOMUX_PAD(0x5d8, 0x194, 1, 0x7e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__I2C3_SDA					IOMUX_PAD(0x5d8, 0x194, 2, 0x920, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__IPU_CSI_D_1				IOMUX_PAD(0x5d8, 0x194, 3, 0x934, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__KPP_COL_7				IOMUX_PAD(0x5d8, 0x194, 4, 0x96c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__GPIO3_9					IOMUX_PAD(0x5d8, 0x194, 5, 0x918, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__EMI_NANDF_CE2				IOMUX_PAD(0x5d8, 0x194, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS1__ARM11P_TOP_EVNTBUS_19			IOMUX_PAD(0x5d8, 0x194, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RXD2__UART2_RXD_MUX				IOMUX_PAD(0x5dc, 0x198, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RXD2__KPP_ROW_4				IOMUX_PAD(0x5dc, 0x198, 4, 0x980, 0, NO_PAD_CTRL)
-#define MX35_PAD_RXD2__GPIO3_10					IOMUX_PAD(0x5dc, 0x198, 5, 0x8ec, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_TXD2__UART2_TXD_MUX				IOMUX_PAD(0x5e0, 0x19c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__SPDIF_SPDIF_EXTCLK			IOMUX_PAD(0x5e0, 0x19c, 1, 0x994, 2, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__KPP_ROW_5				IOMUX_PAD(0x5e0, 0x19c, 4, 0x984, 0, NO_PAD_CTRL)
-#define MX35_PAD_TXD2__GPIO3_11					IOMUX_PAD(0x5e0, 0x19c, 5, 0x8f0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTS2__UART2_RTS				IOMUX_PAD(0x5e4, 0x1a0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__SPDIF_SPDIF_IN1				IOMUX_PAD(0x5e4, 0x1a0, 1, 0x998, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__CAN2_RXCAN				IOMUX_PAD(0x5e4, 0x1a0, 2, 0x7cc, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__IPU_CSI_D_2				IOMUX_PAD(0x5e4, 0x1a0, 3, 0x938, 1, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__KPP_ROW_6				IOMUX_PAD(0x5e4, 0x1a0, 4, 0x988, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__GPIO3_12					IOMUX_PAD(0x5e4, 0x1a0, 5, 0x8f4, 0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__AUDMUX_AUD5_RXC				IOMUX_PAD(0x5e4, 0x1a0, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_RTS2__UART3_RXD_MUX				IOMUX_PAD(0x5e4, 0x1a0, 7, 0x9a0, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_CTS2__UART2_CTS				IOMUX_PAD(0x5e8, 0x1a4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__SPDIF_SPDIF_OUT1				IOMUX_PAD(0x5e8, 0x1a4, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__CAN2_TXCAN				IOMUX_PAD(0x5e8, 0x1a4, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__IPU_CSI_D_3				IOMUX_PAD(0x5e8, 0x1a4, 3, 0x93c, 1, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__KPP_ROW_7				IOMUX_PAD(0x5e8, 0x1a4, 4, 0x98c, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__GPIO3_13					IOMUX_PAD(0x5e8, 0x1a4, 5, 0x8f8, 0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__AUDMUX_AUD5_RXFS				IOMUX_PAD(0x5e8, 0x1a4, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CTS2__UART3_TXD_MUX				IOMUX_PAD(0x5e8, 0x1a4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_RTCK__ARM11P_TOP_RTCK				IOMUX_PAD(0x5ec, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TCK__SJC_TCK					IOMUX_PAD(0x5f0, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TMS__SJC_TMS					IOMUX_PAD(0x5f4, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TDI__SJC_TDI					IOMUX_PAD(0x5f8, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TDO__SJC_TDO					IOMUX_PAD(0x5fc, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TRSTB__SJC_TRSTB				IOMUX_PAD(0x600, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_DE_B__SJC_DE_B					IOMUX_PAD(0x604, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SJC_MOD__SJC_MOD				IOMUX_PAD(0x608, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR			IOMUX_PAD(0x60c, 0x1a8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_PWR__USB_TOP_USBH2_PWR			IOMUX_PAD(0x60c, 0x1a8, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_PWR__GPIO3_14				IOMUX_PAD(0x60c, 0x1a8, 5, 0x8fc, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC			IOMUX_PAD(0x610, 0x1ac, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_OC__USB_TOP_USBH2_OC			IOMUX_PAD(0x610, 0x1ac, 1, 0x9f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_USBOTG_OC__GPIO3_15				IOMUX_PAD(0x610, 0x1ac, 5, 0x900, 0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD0__IPU_DISPB_DAT_0				IOMUX_PAD(0x614, 0x1b0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD0__GPIO2_0					IOMUX_PAD(0x614, 0x1b0, 5, 0x868, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD0__SDMA_SDMA_DEBUG_PC_0			IOMUX_PAD(0x614, 0x1b0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD1__IPU_DISPB_DAT_1				IOMUX_PAD(0x618, 0x1b4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD1__GPIO2_1					IOMUX_PAD(0x618, 0x1b4, 5, 0x894, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD1__SDMA_SDMA_DEBUG_PC_1			IOMUX_PAD(0x618, 0x1b4, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD2__IPU_DISPB_DAT_2				IOMUX_PAD(0x61c, 0x1b8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD2__GPIO2_2					IOMUX_PAD(0x61c, 0x1b8, 5, 0x8c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD2__SDMA_SDMA_DEBUG_PC_2			IOMUX_PAD(0x61c, 0x1b8, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD3__IPU_DISPB_DAT_3				IOMUX_PAD(0x620, 0x1bc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD3__GPIO2_3					IOMUX_PAD(0x620, 0x1bc, 5, 0x8cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD3__SDMA_SDMA_DEBUG_PC_3			IOMUX_PAD(0x620, 0x1bc, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD4__IPU_DISPB_DAT_4				IOMUX_PAD(0x624, 0x1c0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD4__GPIO2_4					IOMUX_PAD(0x624, 0x1c0, 5, 0x8d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD4__SDMA_SDMA_DEBUG_PC_4			IOMUX_PAD(0x624, 0x1c0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD5__IPU_DISPB_DAT_5				IOMUX_PAD(0x628, 0x1c4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD5__GPIO2_5					IOMUX_PAD(0x628, 0x1c4, 5, 0x8d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD5__SDMA_SDMA_DEBUG_PC_5			IOMUX_PAD(0x628, 0x1c4, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD6__IPU_DISPB_DAT_6				IOMUX_PAD(0x62c, 0x1c8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD6__GPIO2_6					IOMUX_PAD(0x62c, 0x1c8, 5, 0x8d8, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD6__SDMA_SDMA_DEBUG_PC_6			IOMUX_PAD(0x62c, 0x1c8, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD7__IPU_DISPB_DAT_7				IOMUX_PAD(0x630, 0x1cc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD7__GPIO2_7					IOMUX_PAD(0x630, 0x1cc, 5, 0x8dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD7__SDMA_SDMA_DEBUG_PC_7			IOMUX_PAD(0x630, 0x1cc, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD8__IPU_DISPB_DAT_8				IOMUX_PAD(0x634, 0x1d0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD8__GPIO2_8					IOMUX_PAD(0x634, 0x1d0, 5, 0x8e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD8__SDMA_SDMA_DEBUG_PC_8			IOMUX_PAD(0x634, 0x1d0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD9__IPU_DISPB_DAT_9				IOMUX_PAD(0x638, 0x1d4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD9__GPIO2_9					IOMUX_PAD(0x638, 0x1d4, 5, 0x8e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD9__SDMA_SDMA_DEBUG_PC_9			IOMUX_PAD(0x638, 0x1d4, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD10__IPU_DISPB_DAT_10				IOMUX_PAD(0x63c, 0x1d8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD10__GPIO2_10					IOMUX_PAD(0x63c, 0x1d8, 5, 0x86c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD10__SDMA_SDMA_DEBUG_PC_10			IOMUX_PAD(0x63c, 0x1d8, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD11__IPU_DISPB_DAT_11				IOMUX_PAD(0x640, 0x1dc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__GPIO2_11					IOMUX_PAD(0x640, 0x1dc, 5, 0x870, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__SDMA_SDMA_DEBUG_PC_11			IOMUX_PAD(0x640, 0x1dc, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD11__ARM11P_TOP_TRACE_4			IOMUX_PAD(0x640, 0x1dc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD12__IPU_DISPB_DAT_12				IOMUX_PAD(0x644, 0x1e0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__GPIO2_12					IOMUX_PAD(0x644, 0x1e0, 5, 0x874, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__SDMA_SDMA_DEBUG_PC_12			IOMUX_PAD(0x644, 0x1e0, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD12__ARM11P_TOP_TRACE_5			IOMUX_PAD(0x644, 0x1e0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD13__IPU_DISPB_DAT_13				IOMUX_PAD(0x648, 0x1e4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__GPIO2_13					IOMUX_PAD(0x648, 0x1e4, 5, 0x878, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__SDMA_SDMA_DEBUG_PC_13			IOMUX_PAD(0x648, 0x1e4, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD13__ARM11P_TOP_TRACE_6			IOMUX_PAD(0x648, 0x1e4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD14__IPU_DISPB_DAT_14				IOMUX_PAD(0x64c, 0x1e8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__GPIO2_14					IOMUX_PAD(0x64c, 0x1e8, 5, 0x87c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__SDMA_SDMA_DEBUG_EVENT_CHANNEL_0		IOMUX_PAD(0x64c, 0x1e8, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD14__ARM11P_TOP_TRACE_7			IOMUX_PAD(0x64c, 0x1e8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD15__IPU_DISPB_DAT_15				IOMUX_PAD(0x650, 0x1ec, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__GPIO2_15					IOMUX_PAD(0x650, 0x1ec, 5, 0x880, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__SDMA_SDMA_DEBUG_EVENT_CHANNEL_1		IOMUX_PAD(0x650, 0x1ec, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD15__ARM11P_TOP_TRACE_8			IOMUX_PAD(0x650, 0x1ec, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD16__IPU_DISPB_DAT_16				IOMUX_PAD(0x654, 0x1f0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__IPU_DISPB_D12_VSYNC			IOMUX_PAD(0x654, 0x1f0, 2, 0x928, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__GPIO2_16					IOMUX_PAD(0x654, 0x1f0, 5, 0x884, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__SDMA_SDMA_DEBUG_EVENT_CHANNEL_2		IOMUX_PAD(0x654, 0x1f0, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD16__ARM11P_TOP_TRACE_9			IOMUX_PAD(0x654, 0x1f0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD17__IPU_DISPB_DAT_17				IOMUX_PAD(0x658, 0x1f4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__IPU_DISPB_CS2				IOMUX_PAD(0x658, 0x1f4, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__GPIO2_17					IOMUX_PAD(0x658, 0x1f4, 5, 0x888, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__SDMA_SDMA_DEBUG_EVENT_CHANNEL_3		IOMUX_PAD(0x658, 0x1f4, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD17__ARM11P_TOP_TRACE_10			IOMUX_PAD(0x658, 0x1f4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD18__IPU_DISPB_DAT_18				IOMUX_PAD(0x65c, 0x1f8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__IPU_DISPB_D0_VSYNC			IOMUX_PAD(0x65c, 0x1f8, 1, 0x924, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD18__IPU_DISPB_D12_VSYNC			IOMUX_PAD(0x65c, 0x1f8, 2, 0x928, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD18__ESDHC3_CMD				IOMUX_PAD(0x65c, 0x1f8, 3, 0x818, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__USB_TOP_USBOTG_DATA_3			IOMUX_PAD(0x65c, 0x1f8, 4, 0x9b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__GPIO3_24					IOMUX_PAD(0x65c, 0x1f8, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__SDMA_SDMA_DEBUG_EVENT_CHANNEL_4		IOMUX_PAD(0x65c, 0x1f8, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD18__ARM11P_TOP_TRACE_11			IOMUX_PAD(0x65c, 0x1f8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD19__IPU_DISPB_DAT_19				IOMUX_PAD(0x660, 0x1fc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__IPU_DISPB_BCLK				IOMUX_PAD(0x660, 0x1fc, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__IPU_DISPB_CS1				IOMUX_PAD(0x660, 0x1fc, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__ESDHC3_CLK				IOMUX_PAD(0x660, 0x1fc, 3, 0x814, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__USB_TOP_USBOTG_DIR			IOMUX_PAD(0x660, 0x1fc, 4, 0x9c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__GPIO3_25					IOMUX_PAD(0x660, 0x1fc, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__SDMA_SDMA_DEBUG_EVENT_CHANNEL_5		IOMUX_PAD(0x660, 0x1fc, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD19__ARM11P_TOP_TRACE_12			IOMUX_PAD(0x660, 0x1fc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD20__IPU_DISPB_DAT_20				IOMUX_PAD(0x664, 0x200, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__IPU_DISPB_CS0				IOMUX_PAD(0x664, 0x200, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__IPU_DISPB_SD_CLK				IOMUX_PAD(0x664, 0x200, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__ESDHC3_DAT0				IOMUX_PAD(0x664, 0x200, 3, 0x81c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__GPIO3_26					IOMUX_PAD(0x664, 0x200, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__SDMA_SDMA_DEBUG_CORE_STATUS_3		IOMUX_PAD(0x664, 0x200, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD20__ARM11P_TOP_TRACE_13			IOMUX_PAD(0x664, 0x200, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD21__IPU_DISPB_DAT_21				IOMUX_PAD(0x668, 0x204, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__IPU_DISPB_PAR_RS				IOMUX_PAD(0x668, 0x204, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__IPU_DISPB_SER_RS				IOMUX_PAD(0x668, 0x204, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__ESDHC3_DAT1				IOMUX_PAD(0x668, 0x204, 3, 0x820, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__USB_TOP_USBOTG_STP			IOMUX_PAD(0x668, 0x204, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__GPIO3_27					IOMUX_PAD(0x668, 0x204, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__SDMA_DEBUG_EVENT_CHANNEL_SEL		IOMUX_PAD(0x668, 0x204, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD21__ARM11P_TOP_TRACE_14			IOMUX_PAD(0x668, 0x204, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD22__IPU_DISPB_DAT_22				IOMUX_PAD(0x66c, 0x208, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__IPU_DISPB_WR				IOMUX_PAD(0x66c, 0x208, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__IPU_DISPB_SD_D_I				IOMUX_PAD(0x66c, 0x208, 2, 0x92c, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__ESDHC3_DAT2				IOMUX_PAD(0x66c, 0x208, 3, 0x824, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__USB_TOP_USBOTG_NXT			IOMUX_PAD(0x66c, 0x208, 4, 0x9c8, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__GPIO3_28					IOMUX_PAD(0x66c, 0x208, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__SDMA_DEBUG_BUS_ERROR			IOMUX_PAD(0x66c, 0x208, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD22__ARM11P_TOP_TRCTL				IOMUX_PAD(0x66c, 0x208, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_LD23__IPU_DISPB_DAT_23				IOMUX_PAD(0x670, 0x20c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__IPU_DISPB_RD				IOMUX_PAD(0x670, 0x20c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__IPU_DISPB_SD_D_IO			IOMUX_PAD(0x670, 0x20c, 2, 0x92c, 1, NO_PAD_CTRL)
-#define MX35_PAD_LD23__ESDHC3_DAT3				IOMUX_PAD(0x670, 0x20c, 3, 0x828, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__USB_TOP_USBOTG_DATA_7			IOMUX_PAD(0x670, 0x20c, 4, 0x9c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__GPIO3_29					IOMUX_PAD(0x670, 0x20c, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__SDMA_DEBUG_MATCHED_DMBUS			IOMUX_PAD(0x670, 0x20c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_LD23__ARM11P_TOP_TRCLK				IOMUX_PAD(0x670, 0x20c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC			IOMUX_PAD(0x674, 0x210, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__IPU_DISPB_SD_D_IO			IOMUX_PAD(0x674, 0x210, 2, 0x92c, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__GPIO3_30				IOMUX_PAD(0x674, 0x210, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__SDMA_DEBUG_RTBUFFER_WRITE		IOMUX_PAD(0x674, 0x210, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_HSYNC__ARM11P_TOP_TRACE_15			IOMUX_PAD(0x674, 0x210, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK			IOMUX_PAD(0x678, 0x214, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__IPU_DISPB_SD_CLK			IOMUX_PAD(0x678, 0x214, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__GPIO3_31				IOMUX_PAD(0x678, 0x214, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__SDMA_SDMA_DEBUG_CORE_STATUS_0	IOMUX_PAD(0x678, 0x214, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_FPSHIFT__ARM11P_TOP_TRACE_16		IOMUX_PAD(0x678, 0x214, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY			IOMUX_PAD(0x67c, 0x218, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__IPU_DISPB_SD_D_O			IOMUX_PAD(0x67c, 0x218, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__GPIO1_0				IOMUX_PAD(0x67c, 0x218, 5, 0x82c, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__SDMA_SDMA_DEBUG_CORE_STATUS_1		IOMUX_PAD(0x67c, 0x218, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_DRDY__ARM11P_TOP_TRACE_17			IOMUX_PAD(0x67c, 0x218, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_CONTRAST__IPU_DISPB_CONTR			IOMUX_PAD(0x680, 0x21c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__GPIO1_1				IOMUX_PAD(0x680, 0x21c, 5, 0x838, 2, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__SDMA_SDMA_DEBUG_CORE_STATUS_2	IOMUX_PAD(0x680, 0x21c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_CONTRAST__ARM11P_TOP_TRACE_18			IOMUX_PAD(0x680, 0x21c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC			IOMUX_PAD(0x684, 0x220, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__IPU_DISPB_CS1			IOMUX_PAD(0x684, 0x220, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__GPIO1_2				IOMUX_PAD(0x684, 0x220, 5, 0x848, 1, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__SDMA_DEBUG_YIELD			IOMUX_PAD(0x684, 0x220, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_VSYNC__ARM11P_TOP_TRACE_19			IOMUX_PAD(0x684, 0x220, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_REV__IPU_DISPB_D3_REV			IOMUX_PAD(0x688, 0x224, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__IPU_DISPB_SER_RS			IOMUX_PAD(0x688, 0x224, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__GPIO1_3				IOMUX_PAD(0x688, 0x224, 5, 0x84c, 1, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__SDMA_DEBUG_BUS_RWB			IOMUX_PAD(0x688, 0x224, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_REV__ARM11P_TOP_TRACE_20			IOMUX_PAD(0x688, 0x224, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS			IOMUX_PAD(0x68c, 0x228, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__IPU_DISPB_CS2				IOMUX_PAD(0x68c, 0x228, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__GPIO1_4				IOMUX_PAD(0x68c, 0x228, 5, 0x850, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__SDMA_DEBUG_BUS_DEVICE_0		IOMUX_PAD(0x68c, 0x228, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_CLS__ARM11P_TOP_TRACE_21			IOMUX_PAD(0x68c, 0x228, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_D3_SPL__IPU_DISPB_D3_SPL			IOMUX_PAD(0x690, 0x22c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__IPU_DISPB_D12_VSYNC			IOMUX_PAD(0x690, 0x22c, 2, 0x928, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__GPIO1_5				IOMUX_PAD(0x690, 0x22c, 5, 0x854, 2, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__SDMA_DEBUG_BUS_DEVICE_1		IOMUX_PAD(0x690, 0x22c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_D3_SPL__ARM11P_TOP_TRACE_22			IOMUX_PAD(0x690, 0x22c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_CMD__ESDHC1_CMD				IOMUX_PAD(0x694, 0x230, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__MSHC_SCLK				IOMUX_PAD(0x694, 0x230, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__IPU_DISPB_D0_VSYNC			IOMUX_PAD(0x694, 0x230, 3, 0x924, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__USB_TOP_USBOTG_DATA_4			IOMUX_PAD(0x694, 0x230, 4, 0x9b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__GPIO1_6				IOMUX_PAD(0x694, 0x230, 5, 0x858, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CMD__ARM11P_TOP_TRCTL			IOMUX_PAD(0x694, 0x230, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_CLK__ESDHC1_CLK				IOMUX_PAD(0x698, 0x234, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__MSHC_BS				IOMUX_PAD(0x698, 0x234, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__IPU_DISPB_BCLK			IOMUX_PAD(0x698, 0x234, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__USB_TOP_USBOTG_DATA_5			IOMUX_PAD(0x698, 0x234, 4, 0x9b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__GPIO1_7				IOMUX_PAD(0x698, 0x234, 5, 0x85c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_CLK__ARM11P_TOP_TRCLK			IOMUX_PAD(0x698, 0x234, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA0__ESDHC1_DAT0				IOMUX_PAD(0x69c, 0x238, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__MSHC_DATA_0				IOMUX_PAD(0x69c, 0x238, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__IPU_DISPB_CS0			IOMUX_PAD(0x69c, 0x238, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__USB_TOP_USBOTG_DATA_6		IOMUX_PAD(0x69c, 0x238, 4, 0x9bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__GPIO1_8				IOMUX_PAD(0x69c, 0x238, 5, 0x860, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA0__ARM11P_TOP_TRACE_23			IOMUX_PAD(0x69c, 0x238, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA1__ESDHC1_DAT1				IOMUX_PAD(0x6a0, 0x23c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__MSHC_DATA_1				IOMUX_PAD(0x6a0, 0x23c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__IPU_DISPB_PAR_RS			IOMUX_PAD(0x6a0, 0x23c, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__USB_TOP_USBOTG_DATA_0		IOMUX_PAD(0x6a0, 0x23c, 4, 0x9a4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__GPIO1_9				IOMUX_PAD(0x6a0, 0x23c, 5, 0x864, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA1__ARM11P_TOP_TRACE_24			IOMUX_PAD(0x6a0, 0x23c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA2__ESDHC1_DAT2				IOMUX_PAD(0x6a4, 0x240, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__MSHC_DATA_2				IOMUX_PAD(0x6a4, 0x240, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__IPU_DISPB_WR			IOMUX_PAD(0x6a4, 0x240, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__USB_TOP_USBOTG_DATA_1		IOMUX_PAD(0x6a4, 0x240, 4, 0x9a8, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__GPIO1_10				IOMUX_PAD(0x6a4, 0x240, 5, 0x830, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA2__ARM11P_TOP_TRACE_25			IOMUX_PAD(0x6a4, 0x240, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD1_DATA3__ESDHC1_DAT3				IOMUX_PAD(0x6a8, 0x244, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__MSHC_DATA_3				IOMUX_PAD(0x6a8, 0x244, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__IPU_DISPB_RD			IOMUX_PAD(0x6a8, 0x244, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__USB_TOP_USBOTG_DATA_2		IOMUX_PAD(0x6a8, 0x244, 4, 0x9ac, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__GPIO1_11				IOMUX_PAD(0x6a8, 0x244, 5, 0x834, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD1_DATA3__ARM11P_TOP_TRACE_26			IOMUX_PAD(0x6a8, 0x244, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_CMD__ESDHC2_CMD				IOMUX_PAD(0x6ac, 0x248, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__I2C3_SCL				IOMUX_PAD(0x6ac, 0x248, 1, 0x91c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__ESDHC1_DAT4				IOMUX_PAD(0x6ac, 0x248, 2, 0x804, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__IPU_CSI_D_2				IOMUX_PAD(0x6ac, 0x248, 3, 0x938, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__USB_TOP_USBH2_DATA_4			IOMUX_PAD(0x6ac, 0x248, 4, 0x9dc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__GPIO2_0				IOMUX_PAD(0x6ac, 0x248, 5, 0x868, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__SPDIF_SPDIF_OUT1			IOMUX_PAD(0x6ac, 0x248, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CMD__IPU_DISPB_D12_VSYNC			IOMUX_PAD(0x6ac, 0x248, 7, 0x928, 3, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_CLK__ESDHC2_CLK				IOMUX_PAD(0x6b0, 0x24c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__I2C3_SDA				IOMUX_PAD(0x6b0, 0x24c, 1, 0x920, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__ESDHC1_DAT5				IOMUX_PAD(0x6b0, 0x24c, 2, 0x808, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__IPU_CSI_D_3				IOMUX_PAD(0x6b0, 0x24c, 3, 0x93c, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__USB_TOP_USBH2_DATA_5			IOMUX_PAD(0x6b0, 0x24c, 4, 0x9e0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__GPIO2_1				IOMUX_PAD(0x6b0, 0x24c, 5, 0x894, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__SPDIF_SPDIF_IN1			IOMUX_PAD(0x6b0, 0x24c, 6, 0x998, 2, NO_PAD_CTRL)
-#define MX35_PAD_SD2_CLK__IPU_DISPB_CS2				IOMUX_PAD(0x6b0, 0x24c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA0__ESDHC2_DAT0				IOMUX_PAD(0x6b4, 0x250, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__UART3_RXD_MUX			IOMUX_PAD(0x6b4, 0x250, 1, 0x9a0, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__ESDHC1_DAT6				IOMUX_PAD(0x6b4, 0x250, 2, 0x80c, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__IPU_CSI_D_4				IOMUX_PAD(0x6b4, 0x250, 3, 0x940, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__USB_TOP_USBH2_DATA_6		IOMUX_PAD(0x6b4, 0x250, 4, 0x9e4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__GPIO2_2				IOMUX_PAD(0x6b4, 0x250, 5, 0x8c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA0__SPDIF_SPDIF_EXTCLK			IOMUX_PAD(0x6b4, 0x250, 6, 0x994, 3, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA1__ESDHC2_DAT1				IOMUX_PAD(0x6b8, 0x254, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__UART3_TXD_MUX			IOMUX_PAD(0x6b8, 0x254, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__ESDHC1_DAT7				IOMUX_PAD(0x6b8, 0x254, 2, 0x810, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__IPU_CSI_D_5				IOMUX_PAD(0x6b8, 0x254, 3, 0x944, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__USB_TOP_USBH2_DATA_0		IOMUX_PAD(0x6b8, 0x254, 4, 0x9cc, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA1__GPIO2_3				IOMUX_PAD(0x6b8, 0x254, 5, 0x8cc, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA2__ESDHC2_DAT2				IOMUX_PAD(0x6bc, 0x258, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__UART3_RTS				IOMUX_PAD(0x6bc, 0x258, 1, 0x99c, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__CAN1_RXCAN				IOMUX_PAD(0x6bc, 0x258, 2, 0x7c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__IPU_CSI_D_6				IOMUX_PAD(0x6bc, 0x258, 3, 0x948, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__USB_TOP_USBH2_DATA_1		IOMUX_PAD(0x6bc, 0x258, 4, 0x9d0, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA2__GPIO2_4				IOMUX_PAD(0x6bc, 0x258, 5, 0x8d0, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_SD2_DATA3__ESDHC2_DAT3				IOMUX_PAD(0x6c0, 0x25c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__UART3_CTS				IOMUX_PAD(0x6c0, 0x25c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__CAN1_TXCAN				IOMUX_PAD(0x6c0, 0x25c, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__IPU_CSI_D_7				IOMUX_PAD(0x6c0, 0x25c, 3, 0x94c, 1, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__USB_TOP_USBH2_DATA_2		IOMUX_PAD(0x6c0, 0x25c, 4, 0x9d4, 0, NO_PAD_CTRL)
-#define MX35_PAD_SD2_DATA3__GPIO2_5				IOMUX_PAD(0x6c0, 0x25c, 5, 0x8d4, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_CS0__ATA_CS0				IOMUX_PAD(0x6c4, 0x260, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__CSPI1_SS3				IOMUX_PAD(0x6c4, 0x260, 1, 0x7dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__IPU_DISPB_CS1				IOMUX_PAD(0x6c4, 0x260, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__GPIO2_6				IOMUX_PAD(0x6c4, 0x260, 5, 0x8d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__IPU_DIAGB_0				IOMUX_PAD(0x6c4, 0x260, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS0__ARM11P_TOP_MAX1_HMASTER_0		IOMUX_PAD(0x6c4, 0x260, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_CS1__ATA_CS1				IOMUX_PAD(0x6c8, 0x264, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__IPU_DISPB_CS2				IOMUX_PAD(0x6c8, 0x264, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__CSPI2_SS0				IOMUX_PAD(0x6c8, 0x264, 4, 0x7f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__GPIO2_7				IOMUX_PAD(0x6c8, 0x264, 5, 0x8dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__IPU_DIAGB_1				IOMUX_PAD(0x6c8, 0x264, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_CS1__ARM11P_TOP_MAX1_HMASTER_1		IOMUX_PAD(0x6c8, 0x264, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DIOR__ATA_DIOR				IOMUX_PAD(0x6cc, 0x268, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__ESDHC3_DAT0				IOMUX_PAD(0x6cc, 0x268, 1, 0x81c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__USB_TOP_USBOTG_DIR			IOMUX_PAD(0x6cc, 0x268, 2, 0x9c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__IPU_DISPB_BE0			IOMUX_PAD(0x6cc, 0x268, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__CSPI2_SS1				IOMUX_PAD(0x6cc, 0x268, 4, 0x7f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__GPIO2_8				IOMUX_PAD(0x6cc, 0x268, 5, 0x8e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__IPU_DIAGB_2				IOMUX_PAD(0x6cc, 0x268, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOR__ARM11P_TOP_MAX1_HMASTER_2		IOMUX_PAD(0x6cc, 0x268, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DIOW__ATA_DIOW				IOMUX_PAD(0x6d0, 0x26c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__ESDHC3_DAT1				IOMUX_PAD(0x6d0, 0x26c, 1, 0x820, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__USB_TOP_USBOTG_STP			IOMUX_PAD(0x6d0, 0x26c, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__IPU_DISPB_BE1			IOMUX_PAD(0x6d0, 0x26c, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__CSPI2_MOSI				IOMUX_PAD(0x6d0, 0x26c, 4, 0x7ec, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__GPIO2_9				IOMUX_PAD(0x6d0, 0x26c, 5, 0x8e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__IPU_DIAGB_3				IOMUX_PAD(0x6d0, 0x26c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DIOW__ARM11P_TOP_MAX1_HMASTER_3		IOMUX_PAD(0x6d0, 0x26c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DMACK__ATA_DMACK				IOMUX_PAD(0x6d4, 0x270, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__ESDHC3_DAT2				IOMUX_PAD(0x6d4, 0x270, 1, 0x824, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__USB_TOP_USBOTG_NXT			IOMUX_PAD(0x6d4, 0x270, 2, 0x9c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__CSPI2_MISO				IOMUX_PAD(0x6d4, 0x270, 4, 0x7e8, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__GPIO2_10				IOMUX_PAD(0x6d4, 0x270, 5, 0x86c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__IPU_DIAGB_4				IOMUX_PAD(0x6d4, 0x270, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMACK__ARM11P_TOP_MAX0_HMASTER_0		IOMUX_PAD(0x6d4, 0x270, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_RESET_B__ATA_RESET_B			IOMUX_PAD(0x6d8, 0x274, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__ESDHC3_DAT3			IOMUX_PAD(0x6d8, 0x274, 1, 0x828, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__USB_TOP_USBOTG_DATA_0		IOMUX_PAD(0x6d8, 0x274, 2, 0x9a4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__IPU_DISPB_SD_D_O			IOMUX_PAD(0x6d8, 0x274, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__CSPI2_RDY				IOMUX_PAD(0x6d8, 0x274, 4, 0x7e4, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__GPIO2_11				IOMUX_PAD(0x6d8, 0x274, 5, 0x870, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__IPU_DIAGB_5			IOMUX_PAD(0x6d8, 0x274, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_RESET_B__ARM11P_TOP_MAX0_HMASTER_1		IOMUX_PAD(0x6d8, 0x274, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_IORDY__ATA_IORDY				IOMUX_PAD(0x6dc, 0x278, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ESDHC3_DAT4				IOMUX_PAD(0x6dc, 0x278, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__USB_TOP_USBOTG_DATA_1		IOMUX_PAD(0x6dc, 0x278, 2, 0x9a8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__IPU_DISPB_SD_D_IO			IOMUX_PAD(0x6dc, 0x278, 3, 0x92c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ESDHC2_DAT4				IOMUX_PAD(0x6dc, 0x278, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__GPIO2_12				IOMUX_PAD(0x6dc, 0x278, 5, 0x874, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__IPU_DIAGB_6				IOMUX_PAD(0x6dc, 0x278, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_IORDY__ARM11P_TOP_MAX0_HMASTER_2		IOMUX_PAD(0x6dc, 0x278, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA0__ATA_DATA_0				IOMUX_PAD(0x6e0, 0x27c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ESDHC3_DAT5				IOMUX_PAD(0x6e0, 0x27c, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__USB_TOP_USBOTG_DATA_2		IOMUX_PAD(0x6e0, 0x27c, 2, 0x9ac, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__IPU_DISPB_D12_VSYNC			IOMUX_PAD(0x6e0, 0x27c, 3, 0x928, 4, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ESDHC2_DAT5				IOMUX_PAD(0x6e0, 0x27c, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__GPIO2_13				IOMUX_PAD(0x6e0, 0x27c, 5, 0x878, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__IPU_DIAGB_7				IOMUX_PAD(0x6e0, 0x27c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA0__ARM11P_TOP_MAX0_HMASTER_3		IOMUX_PAD(0x6e0, 0x27c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA1__ATA_DATA_1				IOMUX_PAD(0x6e4, 0x280, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ESDHC3_DAT6				IOMUX_PAD(0x6e4, 0x280, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__USB_TOP_USBOTG_DATA_3		IOMUX_PAD(0x6e4, 0x280, 2, 0x9b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__IPU_DISPB_SD_CLK			IOMUX_PAD(0x6e4, 0x280, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ESDHC2_DAT6				IOMUX_PAD(0x6e4, 0x280, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__GPIO2_14				IOMUX_PAD(0x6e4, 0x280, 5, 0x87c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__IPU_DIAGB_8				IOMUX_PAD(0x6e4, 0x280, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA1__ARM11P_TOP_TRACE_27			IOMUX_PAD(0x6e4, 0x280, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA2__ATA_DATA_2				IOMUX_PAD(0x6e8, 0x284, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ESDHC3_DAT7				IOMUX_PAD(0x6e8, 0x284, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__USB_TOP_USBOTG_DATA_4		IOMUX_PAD(0x6e8, 0x284, 2, 0x9b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__IPU_DISPB_SER_RS			IOMUX_PAD(0x6e8, 0x284, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ESDHC2_DAT7				IOMUX_PAD(0x6e8, 0x284, 4, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__GPIO2_15				IOMUX_PAD(0x6e8, 0x284, 5, 0x880, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__IPU_DIAGB_9				IOMUX_PAD(0x6e8, 0x284, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA2__ARM11P_TOP_TRACE_28			IOMUX_PAD(0x6e8, 0x284, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA3__ATA_DATA_3				IOMUX_PAD(0x6ec, 0x288, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__ESDHC3_CLK				IOMUX_PAD(0x6ec, 0x288, 1, 0x814, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__USB_TOP_USBOTG_DATA_5		IOMUX_PAD(0x6ec, 0x288, 2, 0x9b8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__CSPI2_SCLK				IOMUX_PAD(0x6ec, 0x288, 4, 0x7e0, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__GPIO2_16				IOMUX_PAD(0x6ec, 0x288, 5, 0x884, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__IPU_DIAGB_10			IOMUX_PAD(0x6ec, 0x288, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA3__ARM11P_TOP_TRACE_29			IOMUX_PAD(0x6ec, 0x288, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA4__ATA_DATA_4				IOMUX_PAD(0x6f0, 0x28c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__ESDHC3_CMD				IOMUX_PAD(0x6f0, 0x28c, 1, 0x818, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__USB_TOP_USBOTG_DATA_6		IOMUX_PAD(0x6f0, 0x28c, 2, 0x9bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__GPIO2_17				IOMUX_PAD(0x6f0, 0x28c, 5, 0x888, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__IPU_DIAGB_11			IOMUX_PAD(0x6f0, 0x28c, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA4__ARM11P_TOP_TRACE_30			IOMUX_PAD(0x6f0, 0x28c, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA5__ATA_DATA_5				IOMUX_PAD(0x6f4, 0x290, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__USB_TOP_USBOTG_DATA_7		IOMUX_PAD(0x6f4, 0x290, 2, 0x9c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__GPIO2_18				IOMUX_PAD(0x6f4, 0x290, 5, 0x88c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__IPU_DIAGB_12			IOMUX_PAD(0x6f4, 0x290, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA5__ARM11P_TOP_TRACE_31			IOMUX_PAD(0x6f4, 0x290, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA6__ATA_DATA_6				IOMUX_PAD(0x6f8, 0x294, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__CAN1_TXCAN				IOMUX_PAD(0x6f8, 0x294, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__UART1_DTR				IOMUX_PAD(0x6f8, 0x294, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__AUDMUX_AUD6_TXD			IOMUX_PAD(0x6f8, 0x294, 3, 0x7b4, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__GPIO2_19				IOMUX_PAD(0x6f8, 0x294, 5, 0x890, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA6__IPU_DIAGB_13			IOMUX_PAD(0x6f8, 0x294, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA7__ATA_DATA_7				IOMUX_PAD(0x6fc, 0x298, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__CAN1_RXCAN				IOMUX_PAD(0x6fc, 0x298, 1, 0x7c8, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__UART1_DSR				IOMUX_PAD(0x6fc, 0x298, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__AUDMUX_AUD6_RXD			IOMUX_PAD(0x6fc, 0x298, 3, 0x7b0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__GPIO2_20				IOMUX_PAD(0x6fc, 0x298, 5, 0x898, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA7__IPU_DIAGB_14			IOMUX_PAD(0x6fc, 0x298, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA8__ATA_DATA_8				IOMUX_PAD(0x700, 0x29c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__UART3_RTS				IOMUX_PAD(0x700, 0x29c, 1, 0x99c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__UART1_RI				IOMUX_PAD(0x700, 0x29c, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__AUDMUX_AUD6_TXC			IOMUX_PAD(0x700, 0x29c, 3, 0x7c0, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__GPIO2_21				IOMUX_PAD(0x700, 0x29c, 5, 0x89c, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA8__IPU_DIAGB_15			IOMUX_PAD(0x700, 0x29c, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA9__ATA_DATA_9				IOMUX_PAD(0x704, 0x2a0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__UART3_CTS				IOMUX_PAD(0x704, 0x2a0, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__UART1_DCD				IOMUX_PAD(0x704, 0x2a0, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__AUDMUX_AUD6_TXFS			IOMUX_PAD(0x704, 0x2a0, 3, 0x7c4, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__GPIO2_22				IOMUX_PAD(0x704, 0x2a0, 5, 0x8a0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA9__IPU_DIAGB_16			IOMUX_PAD(0x704, 0x2a0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA10__ATA_DATA_10			IOMUX_PAD(0x708, 0x2a4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__UART3_RXD_MUX			IOMUX_PAD(0x708, 0x2a4, 1, 0x9a0, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__AUDMUX_AUD6_RXC			IOMUX_PAD(0x708, 0x2a4, 3, 0x7b8, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__GPIO2_23				IOMUX_PAD(0x708, 0x2a4, 5, 0x8a4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA10__IPU_DIAGB_17			IOMUX_PAD(0x708, 0x2a4, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA11__ATA_DATA_11			IOMUX_PAD(0x70c, 0x2a8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__UART3_TXD_MUX			IOMUX_PAD(0x70c, 0x2a8, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__AUDMUX_AUD6_RXFS			IOMUX_PAD(0x70c, 0x2a8, 3, 0x7bc, 0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__GPIO2_24				IOMUX_PAD(0x70c, 0x2a8, 5, 0x8a8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA11__IPU_DIAGB_18			IOMUX_PAD(0x70c, 0x2a8, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA12__ATA_DATA_12			IOMUX_PAD(0x710, 0x2ac, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__I2C3_SCL				IOMUX_PAD(0x710, 0x2ac, 1, 0x91c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__GPIO2_25				IOMUX_PAD(0x710, 0x2ac, 5, 0x8ac, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA12__IPU_DIAGB_19			IOMUX_PAD(0x710, 0x2ac, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA13__ATA_DATA_13			IOMUX_PAD(0x714, 0x2b0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__I2C3_SDA				IOMUX_PAD(0x714, 0x2b0, 1, 0x920, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__GPIO2_26				IOMUX_PAD(0x714, 0x2b0, 5, 0x8b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA13__IPU_DIAGB_20			IOMUX_PAD(0x714, 0x2b0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA14__ATA_DATA_14			IOMUX_PAD(0x718, 0x2b4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__IPU_CSI_D_0			IOMUX_PAD(0x718, 0x2b4, 1, 0x930, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__KPP_ROW_0				IOMUX_PAD(0x718, 0x2b4, 3, 0x970, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__GPIO2_27				IOMUX_PAD(0x718, 0x2b4, 5, 0x8b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA14__IPU_DIAGB_21			IOMUX_PAD(0x718, 0x2b4, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DATA15__ATA_DATA_15			IOMUX_PAD(0x71c, 0x2b8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__IPU_CSI_D_1			IOMUX_PAD(0x71c, 0x2b8, 1, 0x934, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__KPP_ROW_1				IOMUX_PAD(0x71c, 0x2b8, 3, 0x974, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__GPIO2_28				IOMUX_PAD(0x71c, 0x2b8, 5, 0x8b8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DATA15__IPU_DIAGB_22			IOMUX_PAD(0x71c, 0x2b8, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_INTRQ__ATA_INTRQ				IOMUX_PAD(0x720, 0x2bc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__IPU_CSI_D_2				IOMUX_PAD(0x720, 0x2bc, 1, 0x938, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__KPP_ROW_2				IOMUX_PAD(0x720, 0x2bc, 3, 0x978, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__GPIO2_29				IOMUX_PAD(0x720, 0x2bc, 5, 0x8bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_INTRQ__IPU_DIAGB_23			IOMUX_PAD(0x720, 0x2bc, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_BUFF_EN__ATA_BUFFER_EN			IOMUX_PAD(0x724, 0x2c0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__IPU_CSI_D_3			IOMUX_PAD(0x724, 0x2c0, 1, 0x93c, 3, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__KPP_ROW_3				IOMUX_PAD(0x724, 0x2c0, 3, 0x97c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__GPIO2_30				IOMUX_PAD(0x724, 0x2c0, 5, 0x8c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_BUFF_EN__IPU_DIAGB_24			IOMUX_PAD(0x724, 0x2c0, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DMARQ__ATA_DMARQ				IOMUX_PAD(0x728, 0x2c4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__IPU_CSI_D_4				IOMUX_PAD(0x728, 0x2c4, 1, 0x940, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__KPP_COL_0				IOMUX_PAD(0x728, 0x2c4, 3, 0x950, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__GPIO2_31				IOMUX_PAD(0x728, 0x2c4, 5, 0x8c8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__IPU_DIAGB_25			IOMUX_PAD(0x728, 0x2c4, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DMARQ__ECT_CTI_TRIG_IN1_4			IOMUX_PAD(0x728, 0x2c4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA0__ATA_DA_0				IOMUX_PAD(0x72c, 0x2c8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__IPU_CSI_D_5				IOMUX_PAD(0x72c, 0x2c8, 1, 0x944, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__KPP_COL_1				IOMUX_PAD(0x72c, 0x2c8, 3, 0x954, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__GPIO3_0				IOMUX_PAD(0x72c, 0x2c8, 5, 0x8e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__IPU_DIAGB_26				IOMUX_PAD(0x72c, 0x2c8, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA0__ECT_CTI_TRIG_IN1_5			IOMUX_PAD(0x72c, 0x2c8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA1__ATA_DA_1				IOMUX_PAD(0x730, 0x2cc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__IPU_CSI_D_6				IOMUX_PAD(0x730, 0x2cc, 1, 0x948, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__KPP_COL_2				IOMUX_PAD(0x730, 0x2cc, 3, 0x958, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__GPIO3_1				IOMUX_PAD(0x730, 0x2cc, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__IPU_DIAGB_27				IOMUX_PAD(0x730, 0x2cc, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA1__ECT_CTI_TRIG_IN1_6			IOMUX_PAD(0x730, 0x2cc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_ATA_DA2__ATA_DA_2				IOMUX_PAD(0x734, 0x2d0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__IPU_CSI_D_7				IOMUX_PAD(0x734, 0x2d0, 1, 0x94c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__KPP_COL_3				IOMUX_PAD(0x734, 0x2d0, 3, 0x95c, 2, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__GPIO3_2				IOMUX_PAD(0x734, 0x2d0, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__IPU_DIAGB_28				IOMUX_PAD(0x734, 0x2d0, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_ATA_DA2__ECT_CTI_TRIG_IN1_7			IOMUX_PAD(0x734, 0x2d0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_CLK__MLB_MLBCLK				IOMUX_PAD(0x738, 0x2d4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_CLK__GPIO3_3				IOMUX_PAD(0x738, 0x2d4, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_DAT__MLB_MLBDAT				IOMUX_PAD(0x73c, 0x2d8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_DAT__GPIO3_4				IOMUX_PAD(0x73c, 0x2d8, 5, 0x904, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_MLB_SIG__MLB_MLBSIG				IOMUX_PAD(0x740, 0x2dc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_MLB_SIG__GPIO3_5				IOMUX_PAD(0x740, 0x2dc, 5, 0x908, 1, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_CLK__FEC_TX_CLK				IOMUX_PAD(0x744, 0x2e0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__ESDHC1_DAT4			IOMUX_PAD(0x744, 0x2e0, 1, 0x804, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__UART3_RXD_MUX			IOMUX_PAD(0x744, 0x2e0, 2, 0x9a0, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__USB_TOP_USBH2_DIR			IOMUX_PAD(0x744, 0x2e0, 3, 0x9ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__CSPI2_MOSI				IOMUX_PAD(0x744, 0x2e0, 4, 0x7ec, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__GPIO3_6				IOMUX_PAD(0x744, 0x2e0, 5, 0x90c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__IPU_DISPB_D12_VSYNC		IOMUX_PAD(0x744, 0x2e0, 6, 0x928, 5, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_CLK__ARM11P_TOP_EVNTBUS_0		IOMUX_PAD(0x744, 0x2e0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_CLK__FEC_RX_CLK				IOMUX_PAD(0x748, 0x2e4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__ESDHC1_DAT5			IOMUX_PAD(0x748, 0x2e4, 1, 0x808, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__UART3_TXD_MUX			IOMUX_PAD(0x748, 0x2e4, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__USB_TOP_USBH2_STP			IOMUX_PAD(0x748, 0x2e4, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__CSPI2_MISO				IOMUX_PAD(0x748, 0x2e4, 4, 0x7e8, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__GPIO3_7				IOMUX_PAD(0x748, 0x2e4, 5, 0x910, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__IPU_DISPB_SD_D_I			IOMUX_PAD(0x748, 0x2e4, 6, 0x92c, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_CLK__ARM11P_TOP_EVNTBUS_1		IOMUX_PAD(0x748, 0x2e4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_DV__FEC_RX_DV				IOMUX_PAD(0x74c, 0x2e8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__ESDHC1_DAT6				IOMUX_PAD(0x74c, 0x2e8, 1, 0x80c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__UART3_RTS				IOMUX_PAD(0x74c, 0x2e8, 2, 0x99c, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__USB_TOP_USBH2_NXT			IOMUX_PAD(0x74c, 0x2e8, 3, 0x9f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__CSPI2_SCLK				IOMUX_PAD(0x74c, 0x2e8, 4, 0x7e0, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__GPIO3_8				IOMUX_PAD(0x74c, 0x2e8, 5, 0x914, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__IPU_DISPB_SD_CLK			IOMUX_PAD(0x74c, 0x2e8, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_DV__ARM11P_TOP_EVNTBUS_2		IOMUX_PAD(0x74c, 0x2e8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_COL__FEC_COL				IOMUX_PAD(0x750, 0x2ec, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__ESDHC1_DAT7				IOMUX_PAD(0x750, 0x2ec, 1, 0x810, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__UART3_CTS				IOMUX_PAD(0x750, 0x2ec, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__USB_TOP_USBH2_DATA_0			IOMUX_PAD(0x750, 0x2ec, 3, 0x9cc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__CSPI2_RDY				IOMUX_PAD(0x750, 0x2ec, 4, 0x7e4, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__GPIO3_9				IOMUX_PAD(0x750, 0x2ec, 5, 0x918, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__IPU_DISPB_SER_RS			IOMUX_PAD(0x750, 0x2ec, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_COL__ARM11P_TOP_EVNTBUS_3			IOMUX_PAD(0x750, 0x2ec, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA0__FEC_RDATA_0			IOMUX_PAD(0x754, 0x2f0, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__PWM_PWMO				IOMUX_PAD(0x754, 0x2f0, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__UART3_DTR				IOMUX_PAD(0x754, 0x2f0, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__USB_TOP_USBH2_DATA_1		IOMUX_PAD(0x754, 0x2f0, 3, 0x9d0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__CSPI2_SS0				IOMUX_PAD(0x754, 0x2f0, 4, 0x7f0, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__GPIO3_10				IOMUX_PAD(0x754, 0x2f0, 5, 0x8ec, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__IPU_DISPB_CS1			IOMUX_PAD(0x754, 0x2f0, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA0__ARM11P_TOP_EVNTBUS_4		IOMUX_PAD(0x754, 0x2f0, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA0__FEC_TDATA_0			IOMUX_PAD(0x758, 0x2f4, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__SPDIF_SPDIF_OUT1			IOMUX_PAD(0x758, 0x2f4, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__UART3_DSR				IOMUX_PAD(0x758, 0x2f4, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__USB_TOP_USBH2_DATA_2		IOMUX_PAD(0x758, 0x2f4, 3, 0x9d4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__CSPI2_SS1				IOMUX_PAD(0x758, 0x2f4, 4, 0x7f4, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__GPIO3_11				IOMUX_PAD(0x758, 0x2f4, 5, 0x8f0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__IPU_DISPB_CS0			IOMUX_PAD(0x758, 0x2f4, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA0__ARM11P_TOP_EVNTBUS_5		IOMUX_PAD(0x758, 0x2f4, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_EN__FEC_TX_EN				IOMUX_PAD(0x75c, 0x2f8, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__SPDIF_SPDIF_IN1			IOMUX_PAD(0x75c, 0x2f8, 1, 0x998, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__UART3_RI				IOMUX_PAD(0x75c, 0x2f8, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__USB_TOP_USBH2_DATA_3		IOMUX_PAD(0x75c, 0x2f8, 3, 0x9d8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__GPIO3_12				IOMUX_PAD(0x75c, 0x2f8, 5, 0x8f4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__IPU_DISPB_PAR_RS			IOMUX_PAD(0x75c, 0x2f8, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_EN__ARM11P_TOP_EVNTBUS_6		IOMUX_PAD(0x75c, 0x2f8, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_MDC__FEC_MDC				IOMUX_PAD(0x760, 0x2fc, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__CAN2_TXCAN				IOMUX_PAD(0x760, 0x2fc, 1, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__UART3_DCD				IOMUX_PAD(0x760, 0x2fc, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__USB_TOP_USBH2_DATA_4			IOMUX_PAD(0x760, 0x2fc, 3, 0x9dc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__GPIO3_13				IOMUX_PAD(0x760, 0x2fc, 5, 0x8f8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__IPU_DISPB_WR				IOMUX_PAD(0x760, 0x2fc, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDC__ARM11P_TOP_EVNTBUS_7			IOMUX_PAD(0x760, 0x2fc, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_MDIO__FEC_MDIO				IOMUX_PAD(0x764, 0x300, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__CAN2_RXCAN				IOMUX_PAD(0x764, 0x300, 1, 0x7cc, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__USB_TOP_USBH2_DATA_5			IOMUX_PAD(0x764, 0x300, 3, 0x9e0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__GPIO3_14				IOMUX_PAD(0x764, 0x300, 5, 0x8fc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__IPU_DISPB_RD				IOMUX_PAD(0x764, 0x300, 6, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_MDIO__ARM11P_TOP_EVNTBUS_8			IOMUX_PAD(0x764, 0x300, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TX_ERR__FEC_TX_ERR				IOMUX_PAD(0x768, 0x304, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__OWIRE_LINE				IOMUX_PAD(0x768, 0x304, 1, 0x990, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__SPDIF_SPDIF_EXTCLK			IOMUX_PAD(0x768, 0x304, 2, 0x994, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__USB_TOP_USBH2_DATA_6		IOMUX_PAD(0x768, 0x304, 3, 0x9e4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__GPIO3_15				IOMUX_PAD(0x768, 0x304, 5, 0x900, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__IPU_DISPB_D0_VSYNC			IOMUX_PAD(0x768, 0x304, 6, 0x924, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TX_ERR__ARM11P_TOP_EVNTBUS_9		IOMUX_PAD(0x768, 0x304, 7, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RX_ERR__FEC_RX_ERR				IOMUX_PAD(0x76c, 0x308, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__IPU_CSI_D_0			IOMUX_PAD(0x76c, 0x308, 1, 0x930, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__USB_TOP_USBH2_DATA_7		IOMUX_PAD(0x76c, 0x308, 3, 0x9e8, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__KPP_COL_4				IOMUX_PAD(0x76c, 0x308, 4, 0x960, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__GPIO3_16				IOMUX_PAD(0x76c, 0x308, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RX_ERR__IPU_DISPB_SD_D_IO			IOMUX_PAD(0x76c, 0x308, 6, 0x92c, 5, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_CRS__FEC_CRS				IOMUX_PAD(0x770, 0x30c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__IPU_CSI_D_1				IOMUX_PAD(0x770, 0x30c, 1, 0x934, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__USB_TOP_USBH2_PWR			IOMUX_PAD(0x770, 0x30c, 3, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__KPP_COL_5				IOMUX_PAD(0x770, 0x30c, 4, 0x964, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__GPIO3_17				IOMUX_PAD(0x770, 0x30c, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_CRS__IPU_FLASH_STROBE			IOMUX_PAD(0x770, 0x30c, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA1__FEC_RDATA_1			IOMUX_PAD(0x774, 0x310, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__IPU_CSI_D_2			IOMUX_PAD(0x774, 0x310, 1, 0x938, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__AUDMUX_AUD6_RXC			IOMUX_PAD(0x774, 0x310, 2, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__USB_TOP_USBH2_OC			IOMUX_PAD(0x774, 0x310, 3, 0x9f4, 2, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__KPP_COL_6				IOMUX_PAD(0x774, 0x310, 4, 0x968, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__GPIO3_18				IOMUX_PAD(0x774, 0x310, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA1__IPU_DISPB_BE0			IOMUX_PAD(0x774, 0x310, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA1__FEC_TDATA_1			IOMUX_PAD(0x778, 0x314, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__IPU_CSI_D_3			IOMUX_PAD(0x778, 0x314, 1, 0x93c, 4, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__AUDMUX_AUD6_RXFS			IOMUX_PAD(0x778, 0x314, 2, 0x7bc, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__KPP_COL_7				IOMUX_PAD(0x778, 0x314, 4, 0x96c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__GPIO3_19				IOMUX_PAD(0x778, 0x314, 5, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA1__IPU_DISPB_BE1			IOMUX_PAD(0x778, 0x314, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA2__FEC_RDATA_2			IOMUX_PAD(0x77c, 0x318, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__IPU_CSI_D_4			IOMUX_PAD(0x77c, 0x318, 1, 0x940, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__AUDMUX_AUD6_TXD			IOMUX_PAD(0x77c, 0x318, 2, 0x7b4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__KPP_ROW_4				IOMUX_PAD(0x77c, 0x318, 4, 0x980, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA2__GPIO3_20				IOMUX_PAD(0x77c, 0x318, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA2__FEC_TDATA_2			IOMUX_PAD(0x780, 0x31c, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__IPU_CSI_D_5			IOMUX_PAD(0x780, 0x31c, 1, 0x944, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__AUDMUX_AUD6_RXD			IOMUX_PAD(0x780, 0x31c, 2, 0x7b0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__KPP_ROW_5				IOMUX_PAD(0x780, 0x31c, 4, 0x984, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA2__GPIO3_21				IOMUX_PAD(0x780, 0x31c, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_RDATA3__FEC_RDATA_3			IOMUX_PAD(0x784, 0x320, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__IPU_CSI_D_6			IOMUX_PAD(0x784, 0x320, 1, 0x948, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__AUDMUX_AUD6_TXC			IOMUX_PAD(0x784, 0x320, 2, 0x7c0, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__KPP_ROW_6				IOMUX_PAD(0x784, 0x320, 4, 0x988, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_RDATA3__GPIO3_22				IOMUX_PAD(0x784, 0x320, 6, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_FEC_TDATA3__FEC_TDATA_3			IOMUX_PAD(0x788, 0x324, 0, 0x0,   0, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__IPU_CSI_D_7			IOMUX_PAD(0x788, 0x324, 1, 0x94c, 3, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__AUDMUX_AUD6_TXFS			IOMUX_PAD(0x788, 0x324, 2, 0x7c4, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__KPP_ROW_7				IOMUX_PAD(0x788, 0x324, 4, 0x98c, 1, NO_PAD_CTRL)
-#define MX35_PAD_FEC_TDATA3__GPIO3_23				IOMUX_PAD(0x788, 0x324, 5, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_EXT_ARMCLK__CCM_EXT_ARMCLK			IOMUX_PAD(0x78c, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-#define MX35_PAD_TEST_MODE__TCU_TEST_MODE			IOMUX_PAD(0x790, 0x0,   0, 0x0,   0, NO_PAD_CTRL)
-
-
-#endif /* __MACH_IOMUX_MX35_H__ */
diff --git a/arch/arm/mach-imx/iomux-v1.c b/arch/arm/mach-imx/iomux-v1.c
deleted file mode 100644
index a4bec3b9b2b3..000000000000
--- a/arch/arm/mach-imx/iomux-v1.c
+++ /dev/null
@@ -1,174 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/plat-mxc/iomux-v1.c
- *
- * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH
- * Copyright (C) 2009 Uwe Kleine-Koenig, Pengutronix
- *
- * Common code for i.MX1, i.MX21 and i.MX27
- */
-
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/gpio.h>
-
-#include <asm/mach/map.h>
-
-#include "hardware.h"
-#include "iomux-v1.h"
-
-static void __iomem *imx_iomuxv1_baseaddr;
-static unsigned imx_iomuxv1_numports;
-
-static inline unsigned long imx_iomuxv1_readl(unsigned offset)
-{
-	return imx_readl(imx_iomuxv1_baseaddr + offset);
-}
-
-static inline void imx_iomuxv1_writel(unsigned long val, unsigned offset)
-{
-	imx_writel(val, imx_iomuxv1_baseaddr + offset);
-}
-
-static inline void imx_iomuxv1_rmwl(unsigned offset,
-		unsigned long mask, unsigned long value)
-{
-	unsigned long reg = imx_iomuxv1_readl(offset);
-
-	reg &= ~mask;
-	reg |= value;
-
-	imx_iomuxv1_writel(reg, offset);
-}
-
-static inline void imx_iomuxv1_set_puen(
-		unsigned int port, unsigned int pin, int on)
-{
-	unsigned long mask = 1 << pin;
-
-	imx_iomuxv1_rmwl(MXC_PUEN(port), mask, on ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_ddir(
-		unsigned int port, unsigned int pin, int out)
-{
-	unsigned long mask = 1 << pin;
-
-	imx_iomuxv1_rmwl(MXC_DDIR(port), mask, out ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_gpr(
-		unsigned int port, unsigned int pin, int af)
-{
-	unsigned long mask = 1 << pin;
-
-	imx_iomuxv1_rmwl(MXC_GPR(port), mask, af ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_gius(
-		unsigned int port, unsigned int pin, int inuse)
-{
-	unsigned long mask = 1 << pin;
-
-	imx_iomuxv1_rmwl(MXC_GIUS(port), mask, inuse ? mask : 0);
-}
-
-static inline void imx_iomuxv1_set_ocr(
-		unsigned int port, unsigned int pin, unsigned int ocr)
-{
-	unsigned long shift = (pin & 0xf) << 1;
-	unsigned long mask = 3 << shift;
-	unsigned long value = ocr << shift;
-	unsigned long offset = pin < 16 ? MXC_OCR1(port) : MXC_OCR2(port);
-
-	imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-static inline void imx_iomuxv1_set_iconfa(
-		unsigned int port, unsigned int pin, unsigned int aout)
-{
-	unsigned long shift = (pin & 0xf) << 1;
-	unsigned long mask = 3 << shift;
-	unsigned long value = aout << shift;
-	unsigned long offset = pin < 16 ? MXC_ICONFA1(port) : MXC_ICONFA2(port);
-
-	imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-static inline void imx_iomuxv1_set_iconfb(
-		unsigned int port, unsigned int pin, unsigned int bout)
-{
-	unsigned long shift = (pin & 0xf) << 1;
-	unsigned long mask = 3 << shift;
-	unsigned long value = bout << shift;
-	unsigned long offset = pin < 16 ? MXC_ICONFB1(port) : MXC_ICONFB2(port);
-
-	imx_iomuxv1_rmwl(offset, mask, value);
-}
-
-int mxc_gpio_mode(int gpio_mode)
-{
-	unsigned int pin = gpio_mode & GPIO_PIN_MASK;
-	unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> GPIO_PORT_SHIFT;
-	unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> GPIO_OCR_SHIFT;
-	unsigned int aout = (gpio_mode >> GPIO_AOUT_SHIFT) & 3;
-	unsigned int bout = (gpio_mode >> GPIO_BOUT_SHIFT) & 3;
-
-	if (port >= imx_iomuxv1_numports)
-		return -EINVAL;
-
-	/* Pullup enable */
-	imx_iomuxv1_set_puen(port, pin, gpio_mode & GPIO_PUEN);
-
-	/* Data direction */
-	imx_iomuxv1_set_ddir(port, pin, gpio_mode & GPIO_OUT);
-
-	/* Primary / alternate function */
-	imx_iomuxv1_set_gpr(port, pin, gpio_mode & GPIO_AF);
-
-	/* use as gpio? */
-	imx_iomuxv1_set_gius(port, pin, !(gpio_mode & (GPIO_PF | GPIO_AF)));
-
-	imx_iomuxv1_set_ocr(port, pin, ocr);
-
-	imx_iomuxv1_set_iconfa(port, pin, aout);
-
-	imx_iomuxv1_set_iconfb(port, pin, bout);
-
-	return 0;
-}
-
-static int imx_iomuxv1_setup_multiple(const int *list, unsigned count)
-{
-	size_t i;
-	int ret = 0;
-
-	for (i = 0; i < count; ++i) {
-		ret = mxc_gpio_mode(list[i]);
-
-		if (ret)
-			return ret;
-	}
-
-	return ret;
-}
-
-int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count,
-		const char *label)
-{
-	int ret;
-
-	ret = imx_iomuxv1_setup_multiple(pin_list, count);
-	return ret;
-}
-
-int __init imx_iomuxv1_init(void __iomem *base, int numports)
-{
-	imx_iomuxv1_baseaddr = base;
-	imx_iomuxv1_numports = numports;
-
-	return 0;
-}
diff --git a/arch/arm/mach-imx/iomux-v1.h b/arch/arm/mach-imx/iomux-v1.h
deleted file mode 100644
index b94852970c7f..000000000000
--- a/arch/arm/mach-imx/iomux-v1.h
+++ /dev/null
@@ -1,81 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Holger Schurig <hs4233@mail.mn-solutions.de>
- */
-#ifndef __MACH_IOMUX_V1_H__
-#define __MACH_IOMUX_V1_H__
-
-/*
-*  GPIO Module and I/O Multiplexer
-*  x = 0..3 for reg_A, reg_B, reg_C, reg_D
-*/
-#define MXC_DDIR(x)	(0x00 + ((x) << 8))
-#define MXC_OCR1(x)	(0x04 + ((x) << 8))
-#define MXC_OCR2(x)	(0x08 + ((x) << 8))
-#define MXC_ICONFA1(x)	(0x0c + ((x) << 8))
-#define MXC_ICONFA2(x)	(0x10 + ((x) << 8))
-#define MXC_ICONFB1(x)	(0x14 + ((x) << 8))
-#define MXC_ICONFB2(x)	(0x18 + ((x) << 8))
-#define MXC_DR(x)	(0x1c + ((x) << 8))
-#define MXC_GIUS(x)	(0x20 + ((x) << 8))
-#define MXC_SSR(x)	(0x24 + ((x) << 8))
-#define MXC_ICR1(x)	(0x28 + ((x) << 8))
-#define MXC_ICR2(x)	(0x2c + ((x) << 8))
-#define MXC_IMR(x)	(0x30 + ((x) << 8))
-#define MXC_ISR(x)	(0x34 + ((x) << 8))
-#define MXC_GPR(x)	(0x38 + ((x) << 8))
-#define MXC_SWR(x)	(0x3c + ((x) << 8))
-#define MXC_PUEN(x)	(0x40 + ((x) << 8))
-
-#define MX1_NUM_GPIO_PORT	4
-#define MX21_NUM_GPIO_PORT	6
-#define MX27_NUM_GPIO_PORT	6
-
-#define GPIO_PIN_MASK 0x1f
-
-#define GPIO_PORT_SHIFT 5
-#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT)
-
-#define GPIO_PORTA	(0 << GPIO_PORT_SHIFT)
-#define GPIO_PORTB	(1 << GPIO_PORT_SHIFT)
-#define GPIO_PORTC	(2 << GPIO_PORT_SHIFT)
-#define GPIO_PORTD	(3 << GPIO_PORT_SHIFT)
-#define GPIO_PORTE	(4 << GPIO_PORT_SHIFT)
-#define GPIO_PORTF	(5 << GPIO_PORT_SHIFT)
-
-#define GPIO_OUT	(1 << 8)
-#define GPIO_IN		(0 << 8)
-#define GPIO_PUEN	(1 << 9)
-
-#define GPIO_PF		(1 << 10)
-#define GPIO_AF		(1 << 11)
-
-#define GPIO_OCR_SHIFT 12
-#define GPIO_OCR_MASK	(3 << GPIO_OCR_SHIFT)
-#define GPIO_AIN	(0 << GPIO_OCR_SHIFT)
-#define GPIO_BIN	(1 << GPIO_OCR_SHIFT)
-#define GPIO_CIN	(2 << GPIO_OCR_SHIFT)
-#define GPIO_GPIO	(3 << GPIO_OCR_SHIFT)
-
-#define GPIO_AOUT_SHIFT	14
-#define GPIO_AOUT_MASK	(3 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT	(0 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_ISR	(1 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_0	(2 << GPIO_AOUT_SHIFT)
-#define GPIO_AOUT_1	(3 << GPIO_AOUT_SHIFT)
-
-#define GPIO_BOUT_SHIFT	16
-#define GPIO_BOUT_MASK	(3 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT	(0 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_ISR	(1 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_0	(2 << GPIO_BOUT_SHIFT)
-#define GPIO_BOUT_1	(3 << GPIO_BOUT_SHIFT)
-
-extern int mxc_gpio_mode(int gpio_mode);
-extern int mxc_gpio_setup_multiple_pins(const int *pin_list, unsigned count,
-		const char *label);
-
-extern int imx_iomuxv1_init(void __iomem *base, int numports);
-
-#endif /* __MACH_IOMUX_V1_H__ */
diff --git a/arch/arm/mach-imx/iomux-v3.c b/arch/arm/mach-imx/iomux-v3.c
deleted file mode 100644
index 043cf3c7cacf..000000000000
--- a/arch/arm/mach-imx/iomux-v3.c
+++ /dev/null
@@ -1,65 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 by Sascha Hauer <kernel@pengutronix.de>
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
- *                       <armlinux@phytec.de>
- */
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/gpio.h>
-
-#include <asm/mach/map.h>
-
-#include "hardware.h"
-#include "iomux-v3.h"
-
-static void __iomem *base;
-
-/*
- * configures a single pad in the iomuxer
- */
-int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad)
-{
-	u32 mux_ctrl_ofs = (pad & MUX_CTRL_OFS_MASK) >> MUX_CTRL_OFS_SHIFT;
-	u32 mux_mode = (pad & MUX_MODE_MASK) >> MUX_MODE_SHIFT;
-	u32 sel_input_ofs = (pad & MUX_SEL_INPUT_OFS_MASK) >> MUX_SEL_INPUT_OFS_SHIFT;
-	u32 sel_input = (pad & MUX_SEL_INPUT_MASK) >> MUX_SEL_INPUT_SHIFT;
-	u32 pad_ctrl_ofs = (pad & MUX_PAD_CTRL_OFS_MASK) >> MUX_PAD_CTRL_OFS_SHIFT;
-	u32 pad_ctrl = (pad & MUX_PAD_CTRL_MASK) >> MUX_PAD_CTRL_SHIFT;
-
-	if (mux_ctrl_ofs)
-		imx_writel(mux_mode, base + mux_ctrl_ofs);
-
-	if (sel_input_ofs)
-		imx_writel(sel_input, base + sel_input_ofs);
-
-	if (!(pad_ctrl & NO_PAD_CTRL) && pad_ctrl_ofs)
-		imx_writel(pad_ctrl, base + pad_ctrl_ofs);
-
-	return 0;
-}
-
-int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
-		unsigned count)
-{
-	const iomux_v3_cfg_t *p = pad_list;
-	int i;
-	int ret;
-
-	for (i = 0; i < count; i++) {
-		ret = mxc_iomux_v3_setup_pad(*p);
-		if (ret)
-			return ret;
-		p++;
-	}
-	return 0;
-}
-
-void mxc_iomux_v3_init(void __iomem *iomux_v3_base)
-{
-	base = iomux_v3_base;
-}
diff --git a/arch/arm/mach-imx/iomux-v3.h b/arch/arm/mach-imx/iomux-v3.h
deleted file mode 100644
index 7db8ec926ff1..000000000000
--- a/arch/arm/mach-imx/iomux-v3.h
+++ /dev/null
@@ -1,130 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH,
- *			<armlinux@phytec.de>
- */
-
-#ifndef __MACH_IOMUX_V3_H__
-#define __MACH_IOMUX_V3_H__
-
-/*
- *	build IOMUX_PAD structure
- *
- * This iomux scheme is based around pads, which are the physical balls
- * on the processor.
- *
- * - Each pad has a pad control register (IOMUXC_SW_PAD_CTRL_x) which controls
- *   things like driving strength and pullup/pulldown.
- * - Each pad can have but not necessarily does have an output routing register
- *   (IOMUXC_SW_MUX_CTL_PAD_x).
- * - Each pad can have but not necessarily does have an input routing register
- *   (IOMUXC_x_SELECT_INPUT)
- *
- * The three register sets do not have a fixed offset to each other,
- * hence we order this table by pad control registers (which all pads
- * have) and put the optional i/o routing registers into additional
- * fields.
- *
- * The naming convention for the pad modes is MX35_PAD_<padname>__<padmode>
- * If <padname> or <padmode> refers to a GPIO, it is named
- * GPIO_<unit>_<num>
- *
- * IOMUX/PAD Bit field definitions
- *
- * MUX_CTRL_OFS:	    0..11 (12)
- * PAD_CTRL_OFS:	   12..23 (12)
- * SEL_INPUT_OFS:	   24..35 (12)
- * MUX_MODE + SION:	   36..40  (5)
- * PAD_CTRL + NO_PAD_CTRL: 41..57 (17)
- * SEL_INP:		   58..61  (4)
- * reserved:		     63    (1)
-*/
-
-typedef u64 iomux_v3_cfg_t;
-
-#define MUX_CTRL_OFS_SHIFT	0
-#define MUX_CTRL_OFS_MASK	((iomux_v3_cfg_t)0xfff << MUX_CTRL_OFS_SHIFT)
-#define MUX_PAD_CTRL_OFS_SHIFT	12
-#define MUX_PAD_CTRL_OFS_MASK	((iomux_v3_cfg_t)0xfff << MUX_PAD_CTRL_OFS_SHIFT)
-#define MUX_SEL_INPUT_OFS_SHIFT	24
-#define MUX_SEL_INPUT_OFS_MASK	((iomux_v3_cfg_t)0xfff << MUX_SEL_INPUT_OFS_SHIFT)
-
-#define MUX_MODE_SHIFT		36
-#define MUX_MODE_MASK		((iomux_v3_cfg_t)0x1f << MUX_MODE_SHIFT)
-#define MUX_PAD_CTRL_SHIFT	41
-#define MUX_PAD_CTRL_MASK	((iomux_v3_cfg_t)0x1ffff << MUX_PAD_CTRL_SHIFT)
-#define MUX_SEL_INPUT_SHIFT	58
-#define MUX_SEL_INPUT_MASK	((iomux_v3_cfg_t)0xf << MUX_SEL_INPUT_SHIFT)
-
-#define MUX_PAD_CTRL(x)		((iomux_v3_cfg_t)(x) << MUX_PAD_CTRL_SHIFT)
-
-#define IOMUX_PAD(_pad_ctrl_ofs, _mux_ctrl_ofs, _mux_mode, _sel_input_ofs, \
-		_sel_input, _pad_ctrl)					\
-	(((iomux_v3_cfg_t)(_mux_ctrl_ofs) << MUX_CTRL_OFS_SHIFT) |	\
-		((iomux_v3_cfg_t)(_mux_mode) << MUX_MODE_SHIFT) |	\
-		((iomux_v3_cfg_t)(_pad_ctrl_ofs) << MUX_PAD_CTRL_OFS_SHIFT) | \
-		((iomux_v3_cfg_t)(_pad_ctrl) << MUX_PAD_CTRL_SHIFT) |	\
-		((iomux_v3_cfg_t)(_sel_input_ofs) << MUX_SEL_INPUT_OFS_SHIFT) | \
-		((iomux_v3_cfg_t)(_sel_input) << MUX_SEL_INPUT_SHIFT))
-
-#define NEW_PAD_CTRL(cfg, pad)	(((cfg) & ~MUX_PAD_CTRL_MASK) | MUX_PAD_CTRL(pad))
-/*
- * Use to set PAD control
- */
-
-#define NO_PAD_CTRL			(1 << 16)
-#define PAD_CTL_DVS			(1 << 13)
-#define PAD_CTL_HYS			(1 << 8)
-
-#define PAD_CTL_PKE			(1 << 7)
-#define PAD_CTL_PUE			(1 << 6 | PAD_CTL_PKE)
-#define PAD_CTL_PUS_100K_DOWN		(0 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_47K_UP		(1 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_100K_UP		(2 << 4 | PAD_CTL_PUE)
-#define PAD_CTL_PUS_22K_UP		(3 << 4 | PAD_CTL_PUE)
-
-#define PAD_CTL_ODE			(1 << 3)
-
-#define PAD_CTL_DSE_LOW			(0 << 1)
-#define PAD_CTL_DSE_MED			(1 << 1)
-#define PAD_CTL_DSE_HIGH		(2 << 1)
-#define PAD_CTL_DSE_MAX			(3 << 1)
-
-#define PAD_CTL_SRE_FAST		(1 << 0)
-#define PAD_CTL_SRE_SLOW		(0 << 0)
-
-#define IOMUX_CONFIG_SION		(0x1 << 4)
-
-#define MX51_NUM_GPIO_PORT	4
-
-#define GPIO_PIN_MASK 0x1f
-
-#define GPIO_PORT_SHIFT 5
-#define GPIO_PORT_MASK (0x7 << GPIO_PORT_SHIFT)
-
-#define GPIO_PORTA	(0 << GPIO_PORT_SHIFT)
-#define GPIO_PORTB	(1 << GPIO_PORT_SHIFT)
-#define GPIO_PORTC	(2 << GPIO_PORT_SHIFT)
-#define GPIO_PORTD	(3 << GPIO_PORT_SHIFT)
-#define GPIO_PORTE	(4 << GPIO_PORT_SHIFT)
-#define GPIO_PORTF	(5 << GPIO_PORT_SHIFT)
-
-/*
- * setups a single pad in the iomuxer
- */
-int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad);
-
-/*
- * setups multiple pads
- * convenient way to call the above function with tables
- */
-int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
-		unsigned count);
-
-/*
- * Initialise the iomux controller
- */
-void mxc_iomux_v3_init(void __iomem *iomux_v3_base);
-
-#endif /* __MACH_IOMUX_V3_H__*/
-
diff --git a/arch/arm/mach-imx/mach-armadillo5x0.c b/arch/arm/mach-imx/mach-armadillo5x0.c
deleted file mode 100644
index 4d9a56fb6989..000000000000
--- a/arch/arm/mach-imx/mach-armadillo5x0.c
+++ /dev/null
@@ -1,562 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * armadillo5x0.c
- *
- * Copyright 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * updates in http://alberdroid.blogspot.com/
- *
- * Based on Atmark Techno, Inc. armadillo 500 BSP 2008
- * Based on mx31ads.c and pcm037.c Great Work!
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/io.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/delay.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "crmregs-imx3.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static int armadillo5x0_pins[] = {
-	/* UART1 */
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-	/* UART2 */
-	MX31_PIN_CTS2__CTS2,
-	MX31_PIN_RTS2__RTS2,
-	MX31_PIN_TXD2__TXD2,
-	MX31_PIN_RXD2__RXD2,
-	/* LAN9118_IRQ */
-	IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO),
-	/* SDHC1 */
-	MX31_PIN_SD1_DATA3__SD1_DATA3,
-	MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA1__SD1_DATA1,
-	MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_CLK__SD1_CLK,
-	MX31_PIN_SD1_CMD__SD1_CMD,
-	/* Framebuffer */
-	MX31_PIN_LD0__LD0,
-	MX31_PIN_LD1__LD1,
-	MX31_PIN_LD2__LD2,
-	MX31_PIN_LD3__LD3,
-	MX31_PIN_LD4__LD4,
-	MX31_PIN_LD5__LD5,
-	MX31_PIN_LD6__LD6,
-	MX31_PIN_LD7__LD7,
-	MX31_PIN_LD8__LD8,
-	MX31_PIN_LD9__LD9,
-	MX31_PIN_LD10__LD10,
-	MX31_PIN_LD11__LD11,
-	MX31_PIN_LD12__LD12,
-	MX31_PIN_LD13__LD13,
-	MX31_PIN_LD14__LD14,
-	MX31_PIN_LD15__LD15,
-	MX31_PIN_LD16__LD16,
-	MX31_PIN_LD17__LD17,
-	MX31_PIN_VSYNC3__VSYNC3,
-	MX31_PIN_HSYNC__HSYNC,
-	MX31_PIN_FPSHIFT__FPSHIFT,
-	MX31_PIN_DRDY0__DRDY0,
-	IOMUX_MODE(MX31_PIN_LCS1, IOMUX_CONFIG_GPIO), /*ADV7125_PSAVE*/
-	/* I2C2 */
-	MX31_PIN_CSPI2_MOSI__SCL,
-	MX31_PIN_CSPI2_MISO__SDA,
-	/* OTG */
-	MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
-	MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
-	MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
-	MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
-	MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
-	MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
-	MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
-	MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
-	MX31_PIN_USBOTG_CLK__USBOTG_CLK,
-	MX31_PIN_USBOTG_DIR__USBOTG_DIR,
-	MX31_PIN_USBOTG_NXT__USBOTG_NXT,
-	MX31_PIN_USBOTG_STP__USBOTG_STP,
-	/* USB host 2 */
-	IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
-};
-
-/* USB */
-
-#define OTG_RESET IOMUX_TO_GPIO(MX31_PIN_STXD4)
-#define USBH2_RESET IOMUX_TO_GPIO(MX31_PIN_SCK6)
-#define USBH2_CS IOMUX_TO_GPIO(MX31_PIN_GPIO1_3)
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbotg_init(struct platform_device *pdev)
-{
-	int err;
-
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
-
-	/* Chip already enabled by hardware */
-	/* OTG phy reset*/
-	err = gpio_request(OTG_RESET, "USB-OTG-RESET");
-	if (err) {
-		pr_err("Failed to request the usb otg reset gpio\n");
-		return err;
-	}
-
-	err = gpio_direction_output(OTG_RESET, 1/*HIGH*/);
-	if (err) {
-		pr_err("Failed to reset the usb otg phy\n");
-		goto otg_free_reset;
-	}
-
-	gpio_set_value(OTG_RESET, 0/*LOW*/);
-	mdelay(5);
-	gpio_set_value(OTG_RESET, 1/*HIGH*/);
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_DIFF_UNI);
-
-otg_free_reset:
-	gpio_free(OTG_RESET);
-	return err;
-}
-
-static int usbh2_init(struct platform_device *pdev)
-{
-	int err;
-
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
-	mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
-
-	/* Enable the chip */
-	err = gpio_request(USBH2_CS, "USB-H2-CS");
-	if (err) {
-		pr_err("Failed to request the usb host 2 CS gpio\n");
-		return err;
-	}
-
-	err = gpio_direction_output(USBH2_CS, 0/*Enabled*/);
-	if (err) {
-		pr_err("Failed to drive the usb host 2 CS gpio\n");
-		goto h2_free_cs;
-	}
-
-	/* H2 phy reset*/
-	err = gpio_request(USBH2_RESET, "USB-H2-RESET");
-	if (err) {
-		pr_err("Failed to request the usb host 2 reset gpio\n");
-		goto h2_free_cs;
-	}
-
-	err = gpio_direction_output(USBH2_RESET, 1/*HIGH*/);
-	if (err) {
-		pr_err("Failed to reset the usb host 2 phy\n");
-		goto h2_free_reset;
-	}
-
-	gpio_set_value(USBH2_RESET, 0/*LOW*/);
-	mdelay(5);
-	gpio_set_value(USBH2_RESET, 1/*HIGH*/);
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_DIFF_UNI);
-
-h2_free_reset:
-	gpio_free(USBH2_RESET);
-h2_free_cs:
-	gpio_free(USBH2_CS);
-	return err;
-}
-
-static struct mxc_usbh_platform_data usbotg_pdata __initdata = {
-	.init	= usbotg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/* RTC over I2C*/
-#define ARMADILLO5X0_RTC_GPIO	IOMUX_TO_GPIO(MX31_PIN_SRXD4)
-
-static struct i2c_board_info armadillo5x0_i2c_rtc = {
-	I2C_BOARD_INFO("s35390a", 0x30),
-};
-
-/* GPIO BUTTONS */
-static struct gpio_keys_button armadillo5x0_buttons[] = {
-	{
-		.code		= KEY_ENTER, /*28*/
-		.gpio		= IOMUX_TO_GPIO(MX31_PIN_SCLK0),
-		.active_low	= 1,
-		.desc		= "menu",
-		.wakeup		= 1,
-	}, {
-		.code		= KEY_BACK, /*158*/
-		.gpio		= IOMUX_TO_GPIO(MX31_PIN_SRST0),
-		.active_low	= 1,
-		.desc		= "back",
-		.wakeup		= 1,
-	}
-};
-
-static const struct gpio_keys_platform_data
-		armadillo5x0_button_data __initconst = {
-	.buttons	= armadillo5x0_buttons,
-	.nbuttons	= ARRAY_SIZE(armadillo5x0_buttons),
-};
-
-/*
- * NAND Flash
- */
-static const struct mxc_nand_platform_data
-armadillo5x0_nand_board_info __initconst = {
-	.width		= 1,
-	.hw_ecc		= 1,
-};
-
-/*
- * MTD NOR Flash
- */
-static struct mtd_partition armadillo5x0_nor_flash_partitions[] = {
-	{
-		.name		= "nor.bootloader",
-		.offset		= 0x00000000,
-		.size		= 4*32*1024,
-	}, {
-		.name		= "nor.kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 16*128*1024,
-	}, {
-		.name		= "nor.userland",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 110*128*1024,
-	}, {
-		.name		= "nor.config",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 1*128*1024,
-	},
-};
-
-static const struct physmap_flash_data
-		armadillo5x0_nor_flash_pdata __initconst = {
-	.width		= 2,
-	.parts		= armadillo5x0_nor_flash_partitions,
-	.nr_parts	= ARRAY_SIZE(armadillo5x0_nor_flash_partitions),
-};
-
-static const struct resource armadillo5x0_nor_flash_resource __initconst = {
-	.flags		= IORESOURCE_MEM,
-	.start		= MX31_CS0_BASE_ADDR,
-	.end		= MX31_CS0_BASE_ADDR + SZ_64M - 1,
-};
-
-/*
- * FB support
- */
-static const struct fb_videomode fb_modedb[] = {
-	{	/* 640x480 @ 60 Hz */
-		.name		= "CRT-VGA",
-		.refresh	= 60,
-		.xres		= 640,
-		.yres		= 480,
-		.pixclock	= 39721,
-		.left_margin	= 35,
-		.right_margin	= 115,
-		.upper_margin	= 43,
-		.lower_margin	= 1,
-		.hsync_len	= 10,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_OE_ACT_HIGH,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}, {/* 800x600 @ 56 Hz */
-		.name		= "CRT-SVGA",
-		.refresh	= 56,
-		.xres		= 800,
-		.yres		= 600,
-		.pixclock	= 30000,
-		.left_margin	= 30,
-		.right_margin	= 108,
-		.upper_margin	= 13,
-		.lower_margin	= 10,
-		.hsync_len	= 10,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_OE_ACT_HIGH | FB_SYNC_HOR_HIGH_ACT |
-				  FB_SYNC_VERT_HIGH_ACT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	},
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
-	.name		= "CRT-VGA",
-	.mode		= fb_modedb,
-	.num_modes	= ARRAY_SIZE(fb_modedb),
-};
-
-/*
- * SDHC 1
- * MMC support
- */
-static int armadillo5x0_sdhc1_get_ro(struct device *dev)
-{
-	return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B));
-}
-
-static int armadillo5x0_sdhc1_init(struct device *dev,
-				   irq_handler_t detect_irq, void *data)
-{
-	int ret;
-	int gpio_det, gpio_wp;
-
-	gpio_det = IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK);
-	gpio_wp = IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B);
-
-	ret = gpio_request(gpio_det, "sdhc-card-detect");
-	if (ret)
-		return ret;
-
-	gpio_direction_input(gpio_det);
-
-	ret = gpio_request(gpio_wp, "sdhc-write-protect");
-	if (ret)
-		goto err_gpio_free;
-
-	gpio_direction_input(gpio_wp);
-
-	/* When supported the trigger type have to be BOTH */
-	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK)),
-			  detect_irq, IRQF_TRIGGER_FALLING,
-			  "sdhc-detect", data);
-
-	if (ret)
-		goto err_gpio_free_2;
-
-	return 0;
-
-err_gpio_free_2:
-	gpio_free(gpio_wp);
-
-err_gpio_free:
-	gpio_free(gpio_det);
-
-	return ret;
-
-}
-
-static void armadillo5x0_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK)), data);
-	gpio_free(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK));
-	gpio_free(IOMUX_TO_GPIO(MX31_PIN_ATA_RESET_B));
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.get_ro = armadillo5x0_sdhc1_get_ro,
-	.init = armadillo5x0_sdhc1_init,
-	.exit = armadillo5x0_sdhc1_exit,
-};
-
-/*
- * SMSC 9118
- * Network support
- */
-static struct resource armadillo5x0_smc911x_resources[] = {
-	{
-		.start	= MX31_CS3_BASE_ADDR,
-		.end	= MX31_CS3_BASE_ADDR + SZ_32M - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
-	},
-};
-
-static struct smsc911x_platform_config smsc911x_info = {
-	.flags		= SMSC911X_USE_16BIT,
-	.irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type       = SMSC911X_IRQ_TYPE_PUSH_PULL,
-};
-
-static struct platform_device armadillo5x0_smc911x_device = {
-	.name           = "smsc911x",
-	.id             = -1,
-	.num_resources  = ARRAY_SIZE(armadillo5x0_smc911x_resources),
-	.resource       = armadillo5x0_smc911x_resources,
-	.dev            = {
-		.platform_data = &smsc911x_info,
-	},
-};
-
-/* UART device data */
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&armadillo5x0_smc911x_device,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-/*
- * Perform board specific initializations
- */
-static void __init armadillo5x0_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(armadillo5x0_pins,
-			ARRAY_SIZE(armadillo5x0_pins), "armadillo5x0");
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
-	imx31_add_imx_i2c1(NULL);
-
-	/* Register UART */
-	imx31_add_imx_uart0(&uart_pdata);
-	imx31_add_imx_uart1(&uart_pdata);
-
-	/* Register FB */
-	imx31_add_ipu_core();
-	imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
-	/* Register NOR Flash */
-	platform_device_register_resndata(NULL, "physmap-flash", -1,
-			&armadillo5x0_nor_flash_resource, 1,
-			&armadillo5x0_nor_flash_pdata,
-			sizeof(armadillo5x0_nor_flash_pdata));
-
-	/* Register NAND Flash */
-	imx31_add_mxc_nand(&armadillo5x0_nand_board_info);
-
-	/* set NAND page size to 2k if not configured via boot mode pins */
-	imx_writel(imx_readl(mx3_ccm_base + MXC_CCM_RCSR) | (1 << 30),
-		   mx3_ccm_base + MXC_CCM_RCSR);
-}
-
-static void __init armadillo5x0_late(void)
-{
-	armadillo5x0_smc911x_resources[1].start =
-		gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
-	armadillo5x0_smc911x_resources[1].end =
-		gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	imx_add_gpio_keys(&armadillo5x0_button_data);
-
-	/* SMSC9118 IRQ pin */
-	gpio_direction_input(MX31_PIN_GPIO1_0);
-
-	/* Register SDHC */
-	imx31_add_mxc_mmc(0, &sdhc_pdata);
-
-	/* RTC */
-	/* Get RTC IRQ and register the chip */
-	if (!gpio_request(ARMADILLO5X0_RTC_GPIO, "rtc")) {
-		if (!gpio_direction_input(ARMADILLO5X0_RTC_GPIO))
-			armadillo5x0_i2c_rtc.irq =
-				gpio_to_irq(ARMADILLO5X0_RTC_GPIO);
-		else
-			gpio_free(ARMADILLO5X0_RTC_GPIO);
-	}
-
-	if (armadillo5x0_i2c_rtc.irq == 0)
-		pr_warn("armadillo5x0_init: failed to get RTC IRQ\n");
-	i2c_register_board_info(1, &armadillo5x0_i2c_rtc, 1);
-
-	/* USB */
-	usbotg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbotg_pdata.otg)
-		imx31_add_mxc_ehci_otg(&usbotg_pdata);
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static void __init armadillo5x0_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(ARMADILLO5X0, "Armadillo-500")
-	/* Maintainer: Alberto Panizzo  */
-	.atag_offset = 0x100,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= armadillo5x0_timer_init,
-	.init_machine = armadillo5x0_init,
-	.init_late	= armadillo5x0_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-bug.c b/arch/arm/mach-imx/mach-bug.c
deleted file mode 100644
index 3929208600f2..000000000000
--- a/arch/arm/mach-imx/mach-bug.c
+++ /dev/null
@@ -1,54 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2011 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const unsigned int bug_pins[] __initconst = {
-	MX31_PIN_PC_RST__CTS5,
-	MX31_PIN_PC_VS2__RTS5,
-	MX31_PIN_PC_BVD2__TXD5,
-	MX31_PIN_PC_BVD1__RXD5,
-};
-
-static void __init bug_board_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(bug_pins,
-				      ARRAY_SIZE(bug_pins), "uart-4");
-	imx31_add_imx_uart4(&uart_pdata);
-}
-
-static void __init bug_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(BUG, "BugLabs BUGBase")
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= bug_timer_init,
-	.init_machine = bug_board_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-imx27.c b/arch/arm/mach-imx/mach-imx27.c
new file mode 100644
index 000000000000..262422a9c196
--- /dev/null
+++ b/arch/arm/mach-imx/mach-imx27.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/mm.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+
+#include "common.h"
+#include "hardware.h"
+#include "mx27.h"
+
+/* MX27 memory map definition */
+static struct map_desc imx27_io_desc[] __initdata = {
+	/*
+	 * this fixed mapping covers:
+	 * - AIPI1
+	 * - AIPI2
+	 * - AITC
+	 * - ROM Patch
+	 * - and some reserved space
+	 */
+	imx_map_entry(MX27, AIPI, MT_DEVICE),
+	/*
+	 * this fixed mapping covers:
+	 * - CSI
+	 * - ATA
+	 */
+	imx_map_entry(MX27, SAHB1, MT_DEVICE),
+	/*
+	 * this fixed mapping covers:
+	 * - EMI
+	 */
+	imx_map_entry(MX27, X_MEMC, MT_DEVICE),
+};
+
+/*
+ * Initialize the memory map. It is called during the
+ * system startup to create static physical to virtual
+ * memory map for the IO modules.
+ */
+static void __init mx27_map_io(void)
+{
+	iotable_init(imx27_io_desc, ARRAY_SIZE(imx27_io_desc));
+}
+
+static void __init imx27_init_early(void)
+{
+	mxc_set_cpu_type(MXC_CPU_MX27);
+}
+
+static void __init mx27_init_irq(void)
+{
+	void __iomem *avic_base;
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,avic");
+	avic_base = of_iomap(np, 0);
+	BUG_ON(!avic_base);
+	mxc_init_irq(avic_base);
+}
+
+static const char * const imx27_dt_board_compat[] __initconst = {
+	"fsl,imx27",
+	NULL
+};
+
+DT_MACHINE_START(IMX27_DT, "Freescale i.MX27 (Device Tree Support)")
+	.map_io		= mx27_map_io,
+	.init_early	= imx27_init_early,
+	.init_irq	= mx27_init_irq,
+	.init_late	= imx27_pm_init,
+	.dt_compat	= imx27_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
deleted file mode 100644
index a329e50928b6..000000000000
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ /dev/null
@@ -1,562 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * mach-imx27_visstrim_m10.c
- *
- * Copyright 2010  Javier Martin <javier.martin@vista-silicon.com>
- *
- * Based on mach-pcm038.c, mach-pca100.c, mach-mx27ads.c and others.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/pca953x.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/dma-map-ops.h>
-#include <linux/leds.h>
-#include <linux/platform_data/asoc-mx27vis.h>
-#include <sound/tlv320aic32x4.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/system_info.h>
-#include <asm/memblock.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-#define TVP5150_RSTN (GPIO_PORTC + 18)
-#define TVP5150_PWDN (GPIO_PORTC + 19)
-#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
-#define SDHC1_IRQ_GPIO IMX_GPIO_NR(2, 25)
-
-#define VERSION_MASK		0x7
-#define MOTHERBOARD_SHIFT	4
-#define EXPBOARD_SHIFT		0
-
-#define MOTHERBOARD_BIT2	(GPIO_PORTD + 31)
-#define MOTHERBOARD_BIT1	(GPIO_PORTD + 30)
-#define MOTHERBOARD_BIT0	(GPIO_PORTD + 29)
-
-#define EXPBOARD_BIT2		(GPIO_PORTD + 25)
-#define EXPBOARD_BIT1		(GPIO_PORTD + 27)
-#define EXPBOARD_BIT0		(GPIO_PORTD + 28)
-
-#define AMP_GAIN_0		(GPIO_PORTF + 9)
-#define AMP_GAIN_1		(GPIO_PORTF + 8)
-#define AMP_MUTE_SDL		(GPIO_PORTE + 5)
-#define AMP_MUTE_SDR		(GPIO_PORTF + 7)
-
-static const int visstrim_m10_pins[] __initconst = {
-	/* UART1 (console) */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* SSI1 */
-	PC20_PF_SSI1_FS,
-	PC21_PF_SSI1_RXD,
-	PC22_PF_SSI1_TXD,
-	PC23_PF_SSI1_CLK,
-	/* SDHC1 */
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	/* Both I2Cs */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* USB OTG */
-	OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
-	PC9_PF_USBOTG_DATA0,
-	PC11_PF_USBOTG_DATA1,
-	PC10_PF_USBOTG_DATA2,
-	PC13_PF_USBOTG_DATA3,
-	PC12_PF_USBOTG_DATA4,
-	PC7_PF_USBOTG_DATA5,
-	PC8_PF_USBOTG_DATA6,
-	PE25_PF_USBOTG_DATA7,
-	PE24_PF_USBOTG_CLK,
-	PE2_PF_USBOTG_DIR,
-	PE0_PF_USBOTG_NXT,
-	PE1_PF_USBOTG_STP,
-	PB23_PF_USB_PWR,
-	PB24_PF_USB_OC,
-	/* CSI */
-	TVP5150_RSTN | GPIO_GPIO | GPIO_OUT,
-	TVP5150_PWDN | GPIO_GPIO | GPIO_OUT,
-	PB10_PF_CSI_D0,
-	PB11_PF_CSI_D1,
-	PB12_PF_CSI_D2,
-	PB13_PF_CSI_D3,
-	PB14_PF_CSI_D4,
-	PB15_PF_CSI_MCLK,
-	PB16_PF_CSI_PIXCLK,
-	PB17_PF_CSI_D5,
-	PB18_PF_CSI_D6,
-	PB19_PF_CSI_D7,
-	PB20_PF_CSI_VSYNC,
-	PB21_PF_CSI_HSYNC,
-	/* mother board version */
-	MOTHERBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	MOTHERBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	MOTHERBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	/* expansion board version */
-	EXPBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	EXPBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	EXPBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
-	/* Audio AMP control */
-	AMP_GAIN_0 | GPIO_GPIO | GPIO_OUT,
-	AMP_GAIN_1 | GPIO_GPIO | GPIO_OUT,
-	AMP_MUTE_SDL | GPIO_GPIO | GPIO_OUT,
-	AMP_MUTE_SDR | GPIO_GPIO | GPIO_OUT,
-};
-
-static struct gpio visstrim_m10_version_gpios[] = {
-	{ EXPBOARD_BIT0, GPIOF_IN, "exp-version-0" },
-	{ EXPBOARD_BIT1, GPIOF_IN, "exp-version-1" },
-	{ EXPBOARD_BIT2, GPIOF_IN, "exp-version-2" },
-	{ MOTHERBOARD_BIT0, GPIOF_IN, "mother-version-0" },
-	{ MOTHERBOARD_BIT1, GPIOF_IN, "mother-version-1" },
-	{ MOTHERBOARD_BIT2, GPIOF_IN, "mother-version-2" },
-};
-
-static const struct gpio visstrim_m10_gpios[] __initconst = {
-	{
-		.gpio = TVP5150_RSTN,
-		.flags = GPIOF_DIR_OUT | GPIOF_INIT_HIGH,
-		.label = "tvp5150_rstn",
-	},
-	{
-		.gpio = TVP5150_PWDN,
-		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
-		.label = "tvp5150_pwdn",
-	},
-	{
-		.gpio = OTG_PHY_CS_GPIO,
-		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
-		.label = "usbotg_cs",
-	},
-	{
-		.gpio = AMP_GAIN_0,
-		.flags = GPIOF_DIR_OUT,
-		.label = "amp-gain-0",
-	},
-	{
-		.gpio = AMP_GAIN_1,
-		.flags = GPIOF_DIR_OUT,
-		.label = "amp-gain-1",
-	},
-	{
-		.gpio = AMP_MUTE_SDL,
-		.flags = GPIOF_DIR_OUT,
-		.label = "amp-mute-sdl",
-	},
-	{
-		.gpio = AMP_MUTE_SDR,
-		.flags = GPIOF_DIR_OUT,
-		.label = "amp-mute-sdr",
-	},
-};
-
-/* Camera */
-static struct mx2_camera_platform_data visstrim_camera = {
-	.flags = MX2_CAMERA_CCIR | MX2_CAMERA_CCIR_INTERLACE |
-		 MX2_CAMERA_PCLK_SAMPLE_RISING,
-	.clk = 100000,
-};
-
-static phys_addr_t mx2_camera_base __initdata;
-#define MX2_CAMERA_BUF_SIZE SZ_8M
-
-static void __init visstrim_analog_camera_init(void)
-{
-	struct platform_device *pdev;
-
-	gpio_set_value(TVP5150_PWDN, 1);
-	ndelay(1);
-	gpio_set_value(TVP5150_RSTN, 0);
-	ndelay(500);
-	gpio_set_value(TVP5150_RSTN, 1);
-	ndelay(200000);
-
-	pdev = imx27_add_mx2_camera(&visstrim_camera);
-	if (IS_ERR(pdev))
-		return;
-
-	dma_declare_coherent_memory(&pdev->dev, mx2_camera_base,
-				    mx2_camera_base, MX2_CAMERA_BUF_SIZE);
-}
-
-static void __init visstrim_reserve(void)
-{
-	/* reserve 4 MiB for mx2-camera */
-	mx2_camera_base = arm_memblock_steal(3 * MX2_CAMERA_BUF_SIZE,
-			MX2_CAMERA_BUF_SIZE);
-}
-
-/* GPIOs used as events for applications */
-static struct gpio_keys_button visstrim_gpio_keys[] = {
-	{
-		.type	= EV_KEY,
-		.code	= KEY_RESTART,
-		.gpio	= (GPIO_PORTC + 15),
-		.desc	= "Default config",
-		.active_low = 0,
-		.wakeup = 1,
-	},
-	{
-		.type	= EV_KEY,
-		.code	= KEY_RECORD,
-		.gpio	= (GPIO_PORTF + 14),
-		.desc	= "Record",
-		.active_low = 0,
-		.wakeup = 1,
-	},
-	{
-		.type   = EV_KEY,
-		.code   = KEY_STOP,
-		.gpio   = (GPIO_PORTF + 13),
-		.desc   = "Stop",
-		.active_low = 0,
-		.wakeup = 1,
-	}
-};
-
-static const struct gpio_keys_platform_data
-		visstrim_gpio_keys_platform_data __initconst = {
-	.buttons	= visstrim_gpio_keys,
-	.nbuttons	= ARRAY_SIZE(visstrim_gpio_keys),
-};
-
-/* led */
-static const struct gpio_led visstrim_m10_leds[] __initconst = {
-	{
-		.name = "visstrim:ld0",
-		.default_trigger = "nand-disk",
-		.gpio = (GPIO_PORTC + 29),
-	},
-	{
-		.name = "visstrim:ld1",
-		.default_trigger = "nand-disk",
-		.gpio = (GPIO_PORTC + 24),
-	},
-	{
-		.name = "visstrim:ld2",
-		.default_trigger = "nand-disk",
-		.gpio = (GPIO_PORTC + 28),
-	},
-	{
-		.name = "visstrim:ld3",
-		.default_trigger = "nand-disk",
-		.gpio = (GPIO_PORTC + 25),
-	},
-};
-
-static const struct gpio_led_platform_data visstrim_m10_led_data __initconst = {
-	.leds = visstrim_m10_leds,
-	.num_leds = ARRAY_SIZE(visstrim_m10_leds),
-};
-
-/* Visstrim_SM10 has a microSD slot connected to sdhc1 */
-static int visstrim_m10_sdhc1_init(struct device *dev,
-		irq_handler_t detect_irq, void *data)
-{
-	int ret;
-
-	ret = request_irq(gpio_to_irq(SDHC1_IRQ_GPIO), detect_irq,
-			  IRQF_TRIGGER_FALLING, "mmc-detect", data);
-	return ret;
-}
-
-static void visstrim_m10_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(SDHC1_IRQ_GPIO), data);
-}
-
-static const struct imxmmc_platform_data visstrim_m10_sdhc_pdata __initconst = {
-	.init = visstrim_m10_sdhc1_init,
-	.exit = visstrim_m10_sdhc1_exit,
-};
-
-/* Visstrim_SM10 NOR flash */
-static struct physmap_flash_data visstrim_m10_flash_data = {
-	.width = 2,
-};
-
-static struct resource visstrim_m10_flash_resource = {
-	.start = 0xc0000000,
-	.end = 0xc0000000 + SZ_64M - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device visstrim_m10_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &visstrim_m10_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &visstrim_m10_flash_resource,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&visstrim_m10_nor_mtd_device,
-};
-
-/* Visstrim_M10 uses UART0 as console */
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-/* I2C */
-static const struct imxi2c_platform_data visstrim_m10_i2c_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct pca953x_platform_data visstrim_m10_pca9555_pdata = {
-	.gpio_base = 240, /* After MX27 internal GPIOs */
-	.invert = 0,
-};
-
-static struct aic32x4_pdata visstrim_m10_aic32x4_pdata = {
-	.power_cfg = AIC32X4_PWR_MICBIAS_2075_LDOIN |
-		     AIC32X4_PWR_AVDD_DVDD_WEAK_DISABLE |
-		     AIC32X4_PWR_AIC32X4_LDO_ENABLE |
-		     AIC32X4_PWR_CMMODE_LDOIN_RANGE_18_36 |
-		     AIC32X4_PWR_CMMODE_HP_LDOIN_POWERED,
-	.micpga_routing = AIC32X4_MICPGA_ROUTE_LMIC_IN2R_10K |
-			 AIC32X4_MICPGA_ROUTE_RMIC_IN1L_10K,
-	.swapdacs = false,
-};
-
-static struct i2c_board_info visstrim_m10_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pca9555", 0x20),
-		.platform_data = &visstrim_m10_pca9555_pdata,
-	},
-	{
-		I2C_BOARD_INFO("tlv320aic32x4", 0x18),
-		.platform_data = &visstrim_m10_aic32x4_pdata,
-	},
-	{
-		 I2C_BOARD_INFO("m41t00", 0x68),
-	}
-};
-
-/* USB OTG */
-static int otg_phy_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static const struct mxc_usbh_platform_data
-visstrim_m10_usbotg_pdata __initconst = {
-	.init = otg_phy_init,
-	.portsc	= MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/* SSI */
-static const struct imx_ssi_platform_data visstrim_m10_ssi_pdata __initconst = {
-	.flags			= IMX_SSI_DMA | IMX_SSI_SYN,
-};
-
-/* coda */
-
-static void __init visstrim_coda_init(void)
-{
-	struct platform_device *pdev;
-
-	pdev = imx27_add_coda();
-	dma_declare_coherent_memory(&pdev->dev,
-				    mx2_camera_base + MX2_CAMERA_BUF_SIZE,
-				    mx2_camera_base + MX2_CAMERA_BUF_SIZE,
-				    MX2_CAMERA_BUF_SIZE);
-}
-
-/* DMA deinterlace */
-static struct platform_device visstrim_deinterlace = {
-	.name = "m2m-deinterlace",
-	.id = 0,
-};
-
-static void __init visstrim_deinterlace_init(void)
-{
-	int ret = -ENOMEM;
-	struct platform_device *pdev = &visstrim_deinterlace;
-
-	ret = platform_device_register(pdev);
-
-	dma_declare_coherent_memory(&pdev->dev,
-				    mx2_camera_base + 2 * MX2_CAMERA_BUF_SIZE,
-				    mx2_camera_base + 2 * MX2_CAMERA_BUF_SIZE,
-				    MX2_CAMERA_BUF_SIZE);
-}
-
-/* Emma-PrP for format conversion */
-static void __init visstrim_emmaprp_init(void)
-{
-	struct platform_device *pdev;
-	int ret;
-
-	pdev = imx27_add_mx2_emmaprp();
-	if (IS_ERR(pdev))
-		return;
-
-	/*
-	 * Use the same memory area as the analog camera since both
-	 * devices are, by nature, exclusive.
-	 */
-	ret = dma_declare_coherent_memory(&pdev->dev,
-				mx2_camera_base, mx2_camera_base,
-				MX2_CAMERA_BUF_SIZE);
-	if (ret)
-		pr_err("Failed to declare memory for emmaprp\n");
-}
-
-/* Audio */
-static const struct snd_mx27vis_platform_data snd_mx27vis_pdata __initconst = {
-	.amp_gain0_gpio = AMP_GAIN_0,
-	.amp_gain1_gpio = AMP_GAIN_1,
-	.amp_mutel_gpio = AMP_MUTE_SDL,
-	.amp_muter_gpio = AMP_MUTE_SDR,
-};
-
-static void __init visstrim_m10_revision(void)
-{
-	int exp_version = 0;
-	int mo_version = 0;
-	int ret;
-
-	ret = gpio_request_array(visstrim_m10_version_gpios,
-				 ARRAY_SIZE(visstrim_m10_version_gpios));
-	if (ret) {
-		pr_err("Failed to request version gpios");
-		return;
-	}
-
-	/* Get expansion board version (negative logic) */
-	exp_version |= !gpio_get_value(EXPBOARD_BIT2) << 2;
-	exp_version |= !gpio_get_value(EXPBOARD_BIT1) << 1;
-	exp_version |= !gpio_get_value(EXPBOARD_BIT0);
-
-	/* Get mother board version (negative logic) */
-	mo_version |= !gpio_get_value(MOTHERBOARD_BIT2) << 2;
-	mo_version |= !gpio_get_value(MOTHERBOARD_BIT1) << 1;
-	mo_version |= !gpio_get_value(MOTHERBOARD_BIT0);
-
-	system_rev = 0x27000;
-	system_rev |= (mo_version << MOTHERBOARD_SHIFT);
-	system_rev |= (exp_version << EXPBOARD_SHIFT);
-}
-
-static void __init visstrim_m10_board_init(void)
-{
-	int ret;
-
-	imx27_soc_init();
-	visstrim_m10_revision();
-
-	ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins,
-			ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10");
-	if (ret)
-		pr_err("Failed to setup pins (%d)\n", ret);
-
-	imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
-	imx27_add_imx_uart0(&uart_pdata);
-
-	imx27_add_imx_i2c(0, &visstrim_m10_i2c_data);
-	imx27_add_imx_i2c(1, &visstrim_m10_i2c_data);
-	i2c_register_board_info(0, visstrim_m10_i2c_devices,
-				ARRAY_SIZE(visstrim_m10_i2c_devices));
-
-	imx27_add_mxc_mmc(0, &visstrim_m10_sdhc_pdata);
-	imx27_add_mxc_ehci_otg(&visstrim_m10_usbotg_pdata);
-	imx27_add_fec(NULL);
-
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-}
-
-static void __init visstrim_m10_late_init(void)
-{
-	int mo_version, ret;
-
-	ret = gpio_request_array(visstrim_m10_gpios,
-				 ARRAY_SIZE(visstrim_m10_gpios));
-	if (ret)
-		pr_err("Failed to request gpios (%d)\n", ret);
-
-	imx_add_gpio_keys(&visstrim_gpio_keys_platform_data);
-
-	imx_add_platform_device("mx27vis", 0, NULL, 0, &snd_mx27vis_pdata,
-				sizeof(snd_mx27vis_pdata));
-
-	gpio_led_register_device(0, &visstrim_m10_led_data);
-
-	/* Use mother board version to decide what video devices we shall use */
-	mo_version = (system_rev >> MOTHERBOARD_SHIFT) & VERSION_MASK;
-	if (mo_version & 0x1) {
-		visstrim_emmaprp_init();
-
-		/*
-		 * Despite not being used, tvp5150 must be
-		 * powered on to avoid I2C problems. To minimize
-		 * power consupmtion keep reset enabled.
-		 */
-		gpio_set_value(TVP5150_PWDN, 1);
-		ndelay(1);
-		gpio_set_value(TVP5150_RSTN, 0);
-	} else {
-		visstrim_deinterlace_init();
-		visstrim_analog_camera_init();
-	}
-
-	visstrim_coda_init();
-}
-
-static void __init visstrim_m10_timer_init(void)
-{
-	mx27_clocks_init((unsigned long)25000000);
-}
-
-MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
-	.atag_offset = 0x100,
-	.reserve = visstrim_reserve,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= visstrim_m10_timer_init,
-	.init_machine = visstrim_m10_board_init,
-	.init_late	= visstrim_m10_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/imx31-dt.c b/arch/arm/mach-imx/mach-imx31.c
index dc69dfe600df..dc69dfe600df 100644
--- a/arch/arm/mach-imx/imx31-dt.c
+++ b/arch/arm/mach-imx/mach-imx31.c
diff --git a/arch/arm/mach-imx/imx35-dt.c b/arch/arm/mach-imx/mach-imx35.c
index ec5c3068715c..ec5c3068715c 100644
--- a/arch/arm/mach-imx/imx35-dt.c
+++ b/arch/arm/mach-imx/mach-imx35.c
diff --git a/arch/arm/mach-imx/mach-imx7ulp.c b/arch/arm/mach-imx/mach-imx7ulp.c
index 128cf4c92aab..445256e6a4a0 100644
--- a/arch/arm/mach-imx/mach-imx7ulp.c
+++ b/arch/arm/mach-imx/mach-imx7ulp.c
@@ -67,6 +67,9 @@ static const char *const imx7ulp_dt_compat[] __initconst = {
 
 static void __init imx7ulp_init_late(void)
 {
+	if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+		platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+
 	imx7ulp_cpuidle_init();
 }
 
diff --git a/arch/arm/mach-imx/mach-kzm_arm11_01.c b/arch/arm/mach-imx/mach-kzm_arm11_01.c
deleted file mode 100644
index 63f7f78a77af..000000000000
--- a/arch/arm/mach-imx/mach-kzm_arm11_01.c
+++ /dev/null
@@ -1,291 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * KZM-ARM11-01 support
- *  Copyright (C) 2009  Yoichi Yuasa <yuasa@linux-mips.org>
- *
- * based on code for MX31ADS,
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/smsc911x.h>
-#include <linux/types.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <asm/memory.h>
-#include <asm/setup.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-#define KZM_ARM11_IO_ADDRESS(x) (IOMEM(					\
-	IMX_IO_P2V_MODULE(x, MX31_CS4) ?:				\
-	IMX_IO_P2V_MODULE(x, MX31_CS5)) ?:				\
-	MX31_IO_ADDRESS(x))
-
-/*
- *  KZM-ARM11-01 Board Control Registers on FPGA
- */
-#define KZM_ARM11_CTL1		(MX31_CS4_BASE_ADDR + 0x1000)
-#define KZM_ARM11_CTL2		(MX31_CS4_BASE_ADDR + 0x1001)
-#define KZM_ARM11_RSW1		(MX31_CS4_BASE_ADDR + 0x1002)
-#define KZM_ARM11_BACK_LIGHT	(MX31_CS4_BASE_ADDR + 0x1004)
-#define KZM_ARM11_FPGA_REV	(MX31_CS4_BASE_ADDR + 0x1008)
-#define KZM_ARM11_7SEG_LED	(MX31_CS4_BASE_ADDR + 0x1010)
-#define KZM_ARM11_LEDS		(MX31_CS4_BASE_ADDR + 0x1020)
-#define KZM_ARM11_DIPSW2	(MX31_CS4_BASE_ADDR + 0x1003)
-
-/*
- * External UART for touch panel on FPGA
- */
-#define KZM_ARM11_16550		(MX31_CS4_BASE_ADDR + 0x1050)
-
-#if IS_ENABLED(CONFIG_SERIAL_8250)
-/*
- * KZM-ARM11-01 has an external UART on FPGA
- */
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.membase	= KZM_ARM11_IO_ADDRESS(KZM_ARM11_16550),
-		.mapbase	= KZM_ARM11_16550,
-		/* irq number is run-time assigned */
-		.irqflags	= IRQ_TYPE_EDGE_RISING,
-		.uartclk	= 14745600,
-		.regshift	= 0,
-		.iotype		= UPIO_MEM,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_BUGGY_UART,
-	},
-	{},
-};
-
-static struct resource serial8250_resources[] = {
-	{
-		.start	= KZM_ARM11_16550,
-		.end	= KZM_ARM11_16550 + 0x10,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		/* irq number is run-time assigned */
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device serial_device = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM,
-	.dev		= {
-				.platform_data = serial_platform_data,
-			  },
-	.num_resources	= ARRAY_SIZE(serial8250_resources),
-	.resource	= serial8250_resources,
-};
-
-static int __init kzm_init_ext_uart(void)
-{
-	u8 tmp;
-
-	/*
-	 * GPIO 1-1: external UART interrupt line
-	 */
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO));
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "ext-uart-int");
-	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
-	/*
-	 * Unmask UART interrupt
-	 */
-	tmp = __raw_readb(KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));
-	tmp |= 0x2;
-	__raw_writeb(tmp, KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));
-
-	serial_platform_data[0].irq =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-	serial8250_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-	serial8250_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
-	return platform_device_register(&serial_device);
-}
-#else
-static inline int kzm_init_ext_uart(void)
-{
-	return 0;
-}
-#endif
-
-/*
- * SMSC LAN9118
- */
-#if IS_ENABLED(CONFIG_SMSC911X)
-static struct smsc911x_platform_config kzm_smsc9118_config = {
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
-	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct resource kzm_smsc9118_resources[] = {
-	{
-		.start	= MX31_CS5_BASE_ADDR,
-		.end	= MX31_CS5_BASE_ADDR + SZ_128K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		/* irq number is run-time assigned */
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	},
-};
-
-static struct platform_device kzm_smsc9118_device = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(kzm_smsc9118_resources),
-	.resource	= kzm_smsc9118_resources,
-	.dev		= {
-				.platform_data = &kzm_smsc9118_config,
-			  },
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static int __init kzm_init_smsc9118(void)
-{
-	/*
-	 * GPIO 1-2: SMSC9118 interrupt line
-	 */
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_2, IOMUX_CONFIG_GPIO));
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2), "smsc9118-int");
-	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
-	kzm_smsc9118_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
-	kzm_smsc9118_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
-
-	return platform_device_register(&kzm_smsc9118_device);
-}
-#else
-static inline int kzm_init_smsc9118(void)
-{
-	return 0;
-}
-#endif
-
-#if IS_ENABLED(CONFIG_SERIAL_IMX)
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static void __init kzm_init_imx_uart(void)
-{
-	imx31_add_imx_uart0(&uart_pdata);
-	imx31_add_imx_uart1(&uart_pdata);
-}
-#else
-static inline void kzm_init_imx_uart(void)
-{
-}
-#endif
-
-static int kzm_pins[] __initdata = {
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-	MX31_PIN_DCD_DCE1__DCD_DCE1,
-	MX31_PIN_RI_DCE1__RI_DCE1,
-	MX31_PIN_DSR_DCE1__DSR_DCE1,
-	MX31_PIN_DTR_DCE1__DTR_DCE1,
-	MX31_PIN_CTS2__CTS2,
-	MX31_PIN_RTS2__RTS2,
-	MX31_PIN_TXD2__TXD2,
-	MX31_PIN_RXD2__RXD2,
-	MX31_PIN_DCD_DTE1__DCD_DTE2,
-	MX31_PIN_RI_DTE1__RI_DTE2,
-	MX31_PIN_DSR_DTE1__DSR_DTE2,
-	MX31_PIN_DTR_DTE1__DTR_DTE2,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init kzm_board_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(kzm_pins,
-				      ARRAY_SIZE(kzm_pins), "kzm");
-	kzm_init_imx_uart();
-
-	pr_info("Clock input source is 26MHz\n");
-}
-
-static void __init kzm_late_init(void)
-{
-	kzm_init_ext_uart();
-	kzm_init_smsc9118();
-}
-
-/*
- * This structure defines static mappings for the kzm-arm11-01 board.
- */
-static struct map_desc kzm_io_desc[] __initdata = {
-	{
-		.virtual	= (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
-		.pfn		= __phys_to_pfn(MX31_CS4_BASE_ADDR),
-		.length		= MX31_CS4_SIZE,
-		.type		= MT_DEVICE
-	},
-	{
-		.virtual	= (unsigned long)MX31_CS5_BASE_ADDR_VIRT,
-		.pfn		= __phys_to_pfn(MX31_CS5_BASE_ADDR),
-		.length		= MX31_CS5_SIZE,
-		.type		= MT_DEVICE
-	},
-};
-
-/*
- * Set up static virtual mappings.
- */
-static void __init kzm_map_io(void)
-{
-	mx31_map_io();
-	iotable_init(kzm_io_desc, ARRAY_SIZE(kzm_io_desc));
-}
-
-static void __init kzm_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(KZM_ARM11_01, "Kyoto Microcomputer Co., Ltd. KZM-ARM11-01")
-	.atag_offset = 0x100,
-	.map_io = kzm_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= kzm_timer_init,
-	.init_machine = kzm_board_init,
-	.init_late	= kzm_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
deleted file mode 100644
index ec011e89eb9e..000000000000
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ /dev/null
@@ -1,338 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/physmap.h>
-#include <linux/gpio/driver.h>
-#include <linux/gpio/machine.h>
-#include <linux/gpio.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx21.h"
-#include "hardware.h"
-#include "iomux-mx21.h"
-
-#define MX21ADS_CS8900A_REG		(MX21_CS1_BASE_ADDR + 0x000000)
-#define MX21ADS_ST16C255_IOBASE_REG	(MX21_CS1_BASE_ADDR + 0x200000)
-#define MX21ADS_VERSION_REG		(MX21_CS1_BASE_ADDR + 0x400000)
-#define MX21ADS_IO_REG			(MX21_CS1_BASE_ADDR + 0x800000)
-
-#define MX21ADS_MMC_CD			IMX_GPIO_NR(4, 25)
-#define MX21ADS_CS8900A_IRQ_GPIO	IMX_GPIO_NR(5, 11)
-#define MX21ADS_MMGPIO_BASE		(6 * 32)
-
-/* MX21ADS_IO_REG bit definitions */
-#define MX21ADS_IO_SD_WP		(MX21ADS_MMGPIO_BASE + 0)
-#define MX21ADS_IO_TP6			(MX21ADS_IO_SD_WP)
-#define MX21ADS_IO_SW_SEL		(MX21ADS_MMGPIO_BASE + 1)
-#define MX21ADS_IO_TP7			(MX21ADS_IO_SW_SEL)
-#define MX21ADS_IO_RESET_E_UART		(MX21ADS_MMGPIO_BASE + 2)
-#define MX21ADS_IO_RESET_BASE		(MX21ADS_MMGPIO_BASE + 3)
-#define MX21ADS_IO_CSI_CTL2		(MX21ADS_MMGPIO_BASE + 4)
-#define MX21ADS_IO_CSI_CTL1		(MX21ADS_MMGPIO_BASE + 5)
-#define MX21ADS_IO_CSI_CTL0		(MX21ADS_MMGPIO_BASE + 6)
-#define MX21ADS_IO_UART1_EN		(MX21ADS_MMGPIO_BASE + 7)
-#define MX21ADS_IO_UART4_EN		(MX21ADS_MMGPIO_BASE + 8)
-#define MX21ADS_IO_LCDON		(MX21ADS_MMGPIO_BASE + 9)
-#define MX21ADS_IO_IRDA_EN		(MX21ADS_MMGPIO_BASE + 10)
-#define MX21ADS_IO_IRDA_FIR_SEL		(MX21ADS_MMGPIO_BASE + 11)
-#define MX21ADS_IO_IRDA_MD0_B		(MX21ADS_MMGPIO_BASE + 12)
-#define MX21ADS_IO_IRDA_MD1		(MX21ADS_MMGPIO_BASE + 13)
-#define MX21ADS_IO_LED4_ON		(MX21ADS_MMGPIO_BASE + 14)
-#define MX21ADS_IO_LED3_ON		(MX21ADS_MMGPIO_BASE + 15)
-
-static const int mx21ads_pins[] __initconst = {
-
-	/* CS8900A */
-	(GPIO_PORTE | GPIO_GPIO | GPIO_IN | 11),
-
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-
-	/* UART3 (IrDA) - only TXD and RXD */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-
-	/* UART4 */
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-
-	/* LCDC */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA24_PF_REV,     /* Sharp panel dedicated signal */
-	PA25_PF_CLS,     /* Sharp panel dedicated signal */
-	PA26_PF_PS,      /* Sharp panel dedicated signal */
-	PA27_PF_SPL_SPR, /* Sharp panel dedicated signal */
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-
-	/* MMC/SDHC */
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-
-	/* NFC */
-	PF0_PF_NRFB,
-	PF1_PF_NFCE,
-	PF2_PF_NFWP,
-	PF3_PF_NFCLE,
-	PF4_PF_NFALE,
-	PF5_PF_NFRE,
-	PF6_PF_NFWE,
-	PF7_PF_NFIO0,
-	PF8_PF_NFIO1,
-	PF9_PF_NFIO2,
-	PF10_PF_NFIO3,
-	PF11_PF_NFIO4,
-	PF12_PF_NFIO5,
-	PF13_PF_NFIO6,
-	PF14_PF_NFIO7,
-};
-
-/* ADS's NOR flash: 2x AM29BDS128HE9VKI on 32-bit bus */
-static struct physmap_flash_data mx21ads_flash_data = {
-	.width = 4,
-};
-
-static struct resource mx21ads_flash_resource =
-	DEFINE_RES_MEM(MX21_CS0_BASE_ADDR, SZ_32M);
-
-static struct platform_device mx21ads_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &mx21ads_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &mx21ads_flash_resource,
-};
-
-static struct resource mx21ads_cs8900_resources[] __initdata = {
-	DEFINE_RES_MEM(MX21ADS_CS8900A_REG, SZ_1K),
-	/* irq number is run-time assigned */
-	DEFINE_RES_IRQ(-1),
-};
-
-static const struct platform_device_info mx21ads_cs8900_devinfo __initconst = {
-	.name = "cs89x0",
-	.id = 0,
-	.res = mx21ads_cs8900_resources,
-	.num_res = ARRAY_SIZE(mx21ads_cs8900_resources),
-};
-
-static const struct imxuart_platform_data uart_pdata_rts __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxuart_platform_data uart_pdata_norts __initconst = {
-};
-
-static struct resource mx21ads_mmgpio_resource =
-	DEFINE_RES_MEM_NAMED(MX21ADS_IO_REG, SZ_2, "dat");
-
-static struct bgpio_pdata mx21ads_mmgpio_pdata = {
-	.label	= "mx21ads-mmgpio",
-	.base	= MX21ADS_MMGPIO_BASE,
-	.ngpio	= 16,
-};
-
-static struct platform_device mx21ads_mmgpio = {
-	.name = "basic-mmio-gpio",
-	.id = PLATFORM_DEVID_AUTO,
-	.resource = &mx21ads_mmgpio_resource,
-	.num_resources = 1,
-	.dev = {
-		.platform_data = &mx21ads_mmgpio_pdata,
-	},
-};
-
-static struct regulator_consumer_supply mx21ads_lcd_regulator_consumer =
-	REGULATOR_SUPPLY("lcd", "imx-fb.0");
-
-static struct regulator_init_data mx21ads_lcd_regulator_init_data = {
-	.constraints = {
-		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
-	},
-	.consumer_supplies	= &mx21ads_lcd_regulator_consumer,
-	.num_consumer_supplies	= 1,
-};
-
-static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = {
-	.supply_name	= "LCD",
-	.microvolts	= 3300000,
-	.init_data	= &mx21ads_lcd_regulator_init_data,
-};
-
-static struct platform_device mx21ads_lcd_regulator = {
-	.name = "reg-fixed-voltage",
-	.id = PLATFORM_DEVID_AUTO,
-	.dev = {
-		.platform_data = &mx21ads_lcd_regulator_pdata,
-	},
-};
-
-static struct gpiod_lookup_table mx21ads_lcd_regulator_gpiod_table = {
-	.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
-	.table = {
-		GPIO_LOOKUP("mx21ads-mmgpio", 9, NULL, GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-/*
- * Connected is a portrait Sharp-QVGA display
- * of type: LQ035Q7DB02
- */
-static struct imx_fb_videomode mx21ads_modes[] = {
-	{
-		.mode = {
-			.name		= "Sharp-LQ035Q7",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 188679, /* in ps (5.3MHz) */
-			.hsync_len	= 2,
-			.left_margin	= 6,
-			.right_margin	= 16,
-			.vsync_len	= 1,
-			.upper_margin	= 8,
-			.lower_margin	= 10,
-		},
-		.pcr		= 0xfb108bc7,
-		.bpp		= 16,
-	},
-};
-
-static const struct imx_fb_platform_data mx21ads_fb_data __initconst = {
-	.mode = mx21ads_modes,
-	.num_modes = ARRAY_SIZE(mx21ads_modes),
-
-	.pwmr		= 0x00a903ff,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020008,
-};
-
-static int mx21ads_sdhc_get_ro(struct device *dev)
-{
-	return gpio_get_value(MX21ADS_IO_SD_WP);
-}
-
-static int mx21ads_sdhc_init(struct device *dev, irq_handler_t detect_irq,
-	void *data)
-{
-	int ret;
-
-	ret = gpio_request(MX21ADS_IO_SD_WP, "mmc-ro");
-	if (ret)
-		return ret;
-
-	return request_irq(gpio_to_irq(MX21ADS_MMC_CD), detect_irq,
-			   IRQF_TRIGGER_FALLING, "mmc-detect", data);
-}
-
-static void mx21ads_sdhc_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(MX21ADS_MMC_CD), data);
-	gpio_free(MX21ADS_IO_SD_WP);
-}
-
-static const struct imxmmc_platform_data mx21ads_sdhc_pdata __initconst = {
-	.ocr_avail = MMC_VDD_29_30 | MMC_VDD_30_31, /* 3.0V */
-	.get_ro = mx21ads_sdhc_get_ro,
-	.init = mx21ads_sdhc_init,
-	.exit = mx21ads_sdhc_exit,
-};
-
-static const struct mxc_nand_platform_data
-mx21ads_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&mx21ads_mmgpio,
-	&mx21ads_lcd_regulator,
-	&mx21ads_nor_mtd_device,
-};
-
-static void __init mx21ads_board_init(void)
-{
-	imx21_soc_init();
-
-	mxc_gpio_setup_multiple_pins(mx21ads_pins, ARRAY_SIZE(mx21ads_pins),
-			"mx21ads");
-
-	imx21_add_imx_uart0(&uart_pdata_rts);
-	imx21_add_imx_uart2(&uart_pdata_norts);
-	imx21_add_imx_uart3(&uart_pdata_rts);
-	imx21_add_mxc_nand(&mx21ads_nand_board_info);
-
-	imx21_add_imx_fb(&mx21ads_fb_data);
-}
-
-static void __init mx21ads_late_init(void)
-{
-	imx21_add_mxc_mmc(0, &mx21ads_sdhc_pdata);
-
-	gpiod_add_lookup_table(&mx21ads_lcd_regulator_gpiod_table);
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-
-	mx21ads_cs8900_resources[1].start =
-			gpio_to_irq(MX21ADS_CS8900A_IRQ_GPIO);
-	mx21ads_cs8900_resources[1].end =
-			gpio_to_irq(MX21ADS_CS8900A_IRQ_GPIO);
-	platform_device_register_full(&mx21ads_cs8900_devinfo);
-}
-
-static void __init mx21ads_timer_init(void)
-{
-	mx21_clocks_init(32768, 26000000);
-}
-
-MACHINE_START(MX21ADS, "Freescale i.MX21ADS")
-	/* maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io		= mx21_map_io,
-	.init_early = imx21_init_early,
-	.init_irq = mx21_init_irq,
-	.init_time	= mx21ads_timer_init,
-	.init_machine	= mx21ads_board_init,
-	.init_late	= mx21ads_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
deleted file mode 100644
index 2db4475b7f85..000000000000
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ /dev/null
@@ -1,470 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-/*
- * This machine is known as:
- *  - i.MX27 3-Stack Development System
- *  - i.MX27 Platform Development Kit (i.MX27 PDK)
- */
-
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/irq.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/delay.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-#define SD1_EN_GPIO		IMX_GPIO_NR(2, 25)
-#define OTG_PHY_RESET_GPIO	IMX_GPIO_NR(2, 23)
-#define SPI2_SS0		IMX_GPIO_NR(4, 21)
-#define PMIC_INT		IMX_GPIO_NR(3, 14)
-#define SPI1_SS0		IMX_GPIO_NR(4, 28)
-#define SD1_CD			IMX_GPIO_NR(2, 26)
-#define LCD_RESET		IMX_GPIO_NR(1, 3)
-#define LCD_ENABLE		IMX_GPIO_NR(1, 31)
-
-static const int mx27pdk_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* SDHC1 */
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	SD1_EN_GPIO | GPIO_GPIO | GPIO_OUT,
-	/* OTG */
-	OTG_PHY_RESET_GPIO | GPIO_GPIO | GPIO_OUT,
-	PC7_PF_USBOTG_DATA5,
-	PC8_PF_USBOTG_DATA6,
-	PC9_PF_USBOTG_DATA0,
-	PC10_PF_USBOTG_DATA2,
-	PC11_PF_USBOTG_DATA1,
-	PC12_PF_USBOTG_DATA4,
-	PC13_PF_USBOTG_DATA3,
-	PE0_PF_USBOTG_NXT,
-	PE1_PF_USBOTG_STP,
-	PE2_PF_USBOTG_DIR,
-	PE24_PF_USBOTG_CLK,
-	PE25_PF_USBOTG_DATA7,
-	/* CSPI1 */
-	PD31_PF_CSPI1_MOSI,
-	PD30_PF_CSPI1_MISO,
-	PD29_PF_CSPI1_SCLK,
-	PD25_PF_CSPI1_RDY,
-	SPI1_SS0 | GPIO_GPIO | GPIO_OUT,
-	/* CSPI2 */
-	PD22_PF_CSPI2_SCLK,
-	PD23_PF_CSPI2_MISO,
-	PD24_PF_CSPI2_MOSI,
-	SPI2_SS0 | GPIO_GPIO | GPIO_OUT,
-	/* I2C1 */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	/* PMIC INT */
-	PMIC_INT | GPIO_GPIO | GPIO_IN,
-	/* LCD */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	LCD_ENABLE | GPIO_GPIO | GPIO_OUT,
-	LCD_RESET | GPIO_GPIO | GPIO_OUT,
-	/* SSI4 */
-	PC16_PF_SSI4_FS,
-	PC17_PF_SSI4_RXD,
-	PC18_PF_SSI4_TXD,
-	PC19_PF_SSI4_CLK,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-/*
- * Matrix keyboard
- */
-
-static const uint32_t mx27_3ds_keymap[] = {
-	KEY(0, 0, KEY_UP),
-	KEY(0, 1, KEY_DOWN),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_LEFT),
-	KEY(1, 2, KEY_ENTER),
-	KEY(2, 0, KEY_F6),
-	KEY(2, 1, KEY_F8),
-	KEY(2, 2, KEY_F9),
-	KEY(2, 3, KEY_F10),
-};
-
-static const struct matrix_keymap_data mx27_3ds_keymap_data __initconst = {
-	.keymap		= mx27_3ds_keymap,
-	.keymap_size	= ARRAY_SIZE(mx27_3ds_keymap),
-};
-
-static int mx27_3ds_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-				void *data)
-{
-	return request_irq(gpio_to_irq(SD1_CD), detect_irq,
-	IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, "sdhc1-card-detect", data);
-}
-
-static void mx27_3ds_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(SD1_CD), data);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
-	.init = mx27_3ds_sdhc1_init,
-	.exit = mx27_3ds_sdhc1_exit,
-};
-
-static void mx27_3ds_sdhc1_enable_level_translator(void)
-{
-	/* Turn on TXB0108 OE pin */
-	gpio_request(SD1_EN_GPIO, "sd1_enable");
-	gpio_direction_output(SD1_EN_GPIO, 1);
-}
-
-
-static int otg_phy_init(void)
-{
-	gpio_request(OTG_PHY_RESET_GPIO, "usb-otg-reset");
-	gpio_direction_output(OTG_PHY_RESET_GPIO, 0);
-	mdelay(1);
-	gpio_set_value(OTG_PHY_RESET_GPIO, 1);
-	return 0;
-}
-
-static int mx27_3ds_otg_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= mx27_3ds_otg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx27_3ds_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", mx27_3ds_otg_mode);
-
-/* Regulators */
-static struct regulator_init_data gpo_init = {
-	.constraints = {
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_consumer_supply vmmc1_consumers[] = {
-	REGULATOR_SUPPLY("vcore", "spi0.0"),
-};
-
-static struct regulator_init_data vmmc1_init = {
-	.constraints = {
-		.min_uV	= 2800000,
-		.max_uV = 2800000,
-		.apply_uV = 1,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vmmc1_consumers),
-	.consumer_supplies = vmmc1_consumers,
-};
-
-static struct regulator_consumer_supply vgen_consumers[] = {
-	REGULATOR_SUPPLY("vdd", "spi0.0"),
-};
-
-static struct regulator_init_data vgen_init = {
-	.constraints = {
-		.min_uV	= 1800000,
-		.max_uV = 1800000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vgen_consumers),
-	.consumer_supplies = vgen_consumers,
-};
-
-static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = {
-	{
-		.id = MC13783_REG_VMMC1,
-		.init_data = &vmmc1_init,
-	}, {
-		.id = MC13783_REG_VGEN,
-		.init_data = &vgen_init,
-	}, {
-		.id = MC13783_REG_GPO1, /* Turn on 1.8V */
-		.init_data = &gpo_init,
-	}, {
-		.id = MC13783_REG_GPO3, /* Turn on 3.3V */
-		.init_data = &gpo_init,
-	},
-};
-
-/* MC13783 */
-static struct mc13xxx_codec_platform_data mx27_3ds_codec = {
-	.dac_ssi_port = MC13783_SSI1_PORT,
-	.adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data mc13783_pdata = {
-	.regulators = {
-		.regulators = mx27_3ds_regulators,
-		.num_regulators = ARRAY_SIZE(mx27_3ds_regulators),
-
-	},
-	.flags  = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC |
-						MC13XXX_USE_CODEC,
-	.codec = &mx27_3ds_codec,
-};
-
-static struct imx_ssi_platform_data mx27_3ds_ssi_pdata = {
-	.flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-/* SPI */
-static struct gpiod_lookup_table mx27_spi1_gpiod_table = {
-	.dev_id = "imx27-cspi.0", /* Actual device name for spi1 */
-	.table = {
-		/*
-		 * The i.MX27 has the i.MX21 GPIO controller, the SPI1 CS GPIO
-		 * SPI1_SS0 is numbered IMX_GPIO_NR(4, 28).
-		 *
-		 * This is in "bank 4" which is subtracted by one in the macro
-		 * so this is actually bank 3 on "imx21-gpio.3".
-		 */
-		GPIO_LOOKUP_IDX("imx21-gpio.3", 28, "cs", 0, GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static struct gpiod_lookup_table mx27_spi2_gpiod_table = {
-	.dev_id = "imx27-cspi.1", /* Actual device name for spi2 */
-	.table = {
-		/*
-		 * The i.MX27 has the i.MX21 GPIO controller, the SPI2 CS GPIO
-		 * SPI2_SS0 is numbered IMX_GPIO_NR(4, 21).
-		 *
-		 * This is in "bank 4" which is subtracted by one in the macro
-		 * so this is actually bank 3 on "imx21-gpio.3".
-		 */
-		GPIO_LOOKUP_IDX("imx21-gpio.3", 21, "cs", 0, GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static struct imx_fb_videomode mx27_3ds_modes[] = {
-	{	/* 480x640 @ 60 Hz */
-		.mode = {
-			.name		= "Epson-VGA",
-			.refresh	= 60,
-			.xres		= 480,
-			.yres		= 640,
-			.pixclock	= 41701,
-			.left_margin	= 20,
-			.right_margin	= 41,
-			.upper_margin	= 10,
-			.lower_margin	= 5,
-			.hsync_len	= 20,
-			.vsync_len	= 10,
-			.sync		= FB_SYNC_OE_ACT_HIGH |
-						FB_SYNC_CLK_INVERT,
-			.vmode		= FB_VMODE_NONINTERLACED,
-			.flag		= 0,
-		},
-		.bpp		= 16,
-		.pcr		= 0xFAC08B82,
-	},
-};
-
-static const struct imx_fb_platform_data mx27_3ds_fb_data __initconst = {
-	.mode = mx27_3ds_modes,
-	.num_modes = ARRAY_SIZE(mx27_3ds_modes),
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-/* LCD */
-static struct gpiod_lookup_table mx27_3ds_lcd_gpiod_table = {
-	.dev_id = "spi0.0", /* Bus 0 chipselect 0 */
-	.table = {
-		/*
-		 * The i.MX27 has the i.MX21 GPIO controller, the GPIOs
-		 * numbered IMX_GPIO_NR(1, 3) and IMX_GPIO_NR(1, 31)
-		 * are in "bank 1" which is subtracted by one in the macro
-		 * so these are actually bank 0 on "imx21-gpio.0".
-		 */
-		GPIO_LOOKUP("imx21-gpio.0", 3, "reset", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("imx21-gpio.0", 31, "enable", GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
-	{
-		.modalias	= "mc13783",
-		.max_speed_hz	= 1000000,
-		.bus_num	= 1,
-		.chip_select	= 0, /* SS0 */
-		.platform_data	= &mc13783_pdata,
-		/* irq number is run-time assigned */
-		.mode = SPI_CS_HIGH,
-	}, {
-		.modalias	= "l4f00242t03",
-		.max_speed_hz	= 5000000,
-		.bus_num	= 0,
-		.chip_select	= 0, /* SS0 */
-	},
-};
-
-static const struct imxi2c_platform_data mx27_3ds_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-static void __init mx27pdk_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins),
-		"mx27pdk");
-	imx27_add_imx_uart0(&uart_pdata);
-	imx27_add_fec(NULL);
-	imx27_add_imx_keypad(&mx27_3ds_keymap_data);
-	imx27_add_imx2_wdt();
-
-	imx27_add_spi_imx1(&mx27_spi2_gpiod_table);
-	imx27_add_spi_imx0(&mx27_spi1_gpiod_table);
-
-	imx27_add_imx_i2c(0, &mx27_3ds_i2c0_data);
-	imx27_add_imx_fb(&mx27_3ds_fb_data);
-
-	imx27_add_imx_ssi(0, &mx27_3ds_ssi_pdata);
-}
-
-static void __init mx27pdk_late_init(void)
-{
-	mx27_3ds_sdhc1_enable_level_translator();
-	imx27_add_mxc_mmc(0, &sdhc1_pdata);
-
-	otg_phy_init();
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-
-		if (otg_pdata.otg)
-			imx27_add_mxc_ehci_otg(&otg_pdata);
-	}
-
-	if (!otg_mode_host)
-		imx27_add_fsl_usb2_udc(&otg_device_pdata);
-
-	gpiod_add_lookup_table(&mx27_3ds_lcd_gpiod_table);
-	mx27_3ds_spi_devs[0].irq = gpio_to_irq(PMIC_INT);
-	spi_register_board_info(mx27_3ds_spi_devs,
-				ARRAY_SIZE(mx27_3ds_spi_devs));
-
-	if (mxc_expio_init(MX27_CS5_BASE_ADDR, IMX_GPIO_NR(3, 28)))
-		pr_warn("Init of the debugboard failed, all devices on the debugboard are unusable.\n");
-
-
-	imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-}
-
-static void __init mx27pdk_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(MX27_3DS, "Freescale MX27PDK")
-	/* maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= mx27pdk_timer_init,
-	.init_machine = mx27pdk_init,
-	.init_late	= mx27pdk_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
deleted file mode 100644
index ba202f95bcdf..000000000000
--- a/arch/arm/mach-imx/mach-mx27ads.c
+++ /dev/null
@@ -1,407 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-#include <linux/gpio/driver.h>
-/* Needed for gpio_to_irq() */
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-/*
- * Base address of PBC controller, CS4
- */
-#define PBC_BASE_ADDRESS        0xf4300000
-#define PBC_REG_ADDR(offset)    (void __force __iomem *) \
-		(PBC_BASE_ADDRESS + (offset))
-
-/* When the PBC address connection is fixed in h/w, defined as 1 */
-#define PBC_ADDR_SH             0
-
-/* Offsets for the PBC Controller register */
-/*
- * PBC Board version register offset
- */
-#define PBC_VERSION_REG         PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH)
-/*
- * PBC Board control register 1 set address.
- */
-#define PBC_BCTRL1_SET_REG      PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH)
-/*
- * PBC Board control register 1 clear address.
- */
-#define PBC_BCTRL1_CLEAR_REG    PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH)
-
-/* PBC Board Control Register 1 bit definitions */
-#define PBC_BCTRL1_LCDON        0x0800	/* Enable the LCD */
-
-/* to determine the correct external crystal reference */
-#define CKIH_27MHZ_BIT_SET      (1 << 3)
-
-static const int mx27ads_pins[] __initconst = {
-	/* UART0 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART1 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART2 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* UART3 */
-	PB26_AF_UART4_RTS,
-	PB28_AF_UART4_TXD,
-	PB29_AF_UART4_CTS,
-	PB31_AF_UART4_RXD,
-	/* UART4 */
-	PB18_AF_UART5_TXD,
-	PB19_AF_UART5_RXD,
-	PB20_AF_UART5_CTS,
-	PB21_AF_UART5_RTS,
-	/* UART5 */
-	PB10_AF_UART6_TXD,
-	PB12_AF_UART6_CTS,
-	PB11_AF_UART6_RXD,
-	PB13_AF_UART6_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C2 */
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* FB */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA24_PF_REV,
-	PA25_PF_CLS,
-	PA26_PF_PS,
-	PA27_PF_SPL_SPR,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/* OWIRE */
-	PE16_AF_OWIRE,
-	/* SDHC1*/
-	PE18_PF_SD1_D0,
-	PE19_PF_SD1_D1,
-	PE20_PF_SD1_D2,
-	PE21_PF_SD1_D3,
-	PE22_PF_SD1_CMD,
-	PE23_PF_SD1_CLK,
-	/* SDHC2*/
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-};
-
-static const struct mxc_nand_platform_data
-mx27ads_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-/* ADS's NOR flash */
-static struct physmap_flash_data mx27ads_flash_data = {
-	.width = 2,
-};
-
-static struct resource mx27ads_flash_resource = {
-	.start = 0xc0000000,
-	.end = 0xc0000000 + 0x02000000 - 1,
-	.flags = IORESOURCE_MEM,
-
-};
-
-static struct platform_device mx27ads_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &mx27ads_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &mx27ads_flash_resource,
-};
-
-static const struct imxi2c_platform_data mx27ads_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info mx27ads_i2c_devices[] = {
-};
-
-static void vgpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
-	if (value)
-		imx_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_SET_REG);
-	else
-		imx_writew(PBC_BCTRL1_LCDON, PBC_BCTRL1_CLEAR_REG);
-}
-
-static int vgpio_dir_out(struct gpio_chip *chip, unsigned offset, int value)
-{
-	return 0;
-}
-
-#define MX27ADS_LCD_GPIO	(6 * 32)
-
-static struct regulator_consumer_supply mx27ads_lcd_regulator_consumer =
-	REGULATOR_SUPPLY("lcd", "imx-fb.0");
-
-static struct regulator_init_data mx27ads_lcd_regulator_init_data = {
-	.constraints	= {
-		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
-},
-	.consumer_supplies	= &mx27ads_lcd_regulator_consumer,
-	.num_consumer_supplies	= 1,
-};
-
-static struct fixed_voltage_config mx27ads_lcd_regulator_pdata = {
-	.supply_name	= "LCD",
-	.microvolts	= 3300000,
-	.init_data	= &mx27ads_lcd_regulator_init_data,
-};
-
-static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = {
-	.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
-	.table = {
-		GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static void __init mx27ads_regulator_init(void)
-{
-	struct gpio_chip *vchip;
-
-	vchip = kzalloc(sizeof(*vchip), GFP_KERNEL);
-	vchip->owner		= THIS_MODULE;
-	vchip->label		= "LCD";
-	vchip->base		= MX27ADS_LCD_GPIO;
-	vchip->ngpio		= 1;
-	vchip->direction_output	= vgpio_dir_out;
-	vchip->set		= vgpio_set;
-	gpiochip_add_data(vchip, NULL);
-
-	gpiod_add_lookup_table(&mx27ads_lcd_regulator_gpiod_table);
-
-	platform_device_register_data(NULL, "reg-fixed-voltage",
-				      PLATFORM_DEVID_AUTO,
-				      &mx27ads_lcd_regulator_pdata,
-				      sizeof(mx27ads_lcd_regulator_pdata));
-}
-
-static struct imx_fb_videomode mx27ads_modes[] = {
-	{
-		.mode = {
-			.name		= "Sharp-LQ035Q7",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 188679, /* in ps (5.3MHz) */
-			.hsync_len	= 1,
-			.left_margin	= 9,
-			.right_margin	= 16,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 9,
-		},
-		.bpp		= 16,
-		.pcr		= 0xFB008BC0,
-	},
-};
-
-static const struct imx_fb_platform_data mx27ads_fb_data __initconst = {
-	.mode = mx27ads_modes,
-	.num_modes = ARRAY_SIZE(mx27ads_modes),
-
-	/*
-	 * - HSYNC active high
-	 * - VSYNC active high
-	 * - clk notenabled while idle
-	 * - clock inverted
-	 * - data not inverted
-	 * - data enable low active
-	 * - enable sharp mode
-	 */
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static int mx27ads_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-			      void *data)
-{
-	return request_irq(gpio_to_irq(IMX_GPIO_NR(5, 21)), detect_irq,
-			   IRQF_TRIGGER_RISING, "sdhc1-card-detect", data);
-}
-
-static int mx27ads_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
-			      void *data)
-{
-	return request_irq(gpio_to_irq(IMX_GPIO_NR(2, 7)), detect_irq,
-			   IRQF_TRIGGER_RISING, "sdhc2-card-detect", data);
-}
-
-static void mx27ads_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(5, 21)), data);
-}
-
-static void mx27ads_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(2, 7)), data);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
-	.init = mx27ads_sdhc1_init,
-	.exit = mx27ads_sdhc1_exit,
-};
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
-	.init = mx27ads_sdhc2_init,
-	.exit = mx27ads_sdhc2_exit,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&mx27ads_nor_mtd_device,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static void __init mx27ads_board_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins),
-			"mx27ads");
-
-	imx27_add_imx_uart0(&uart_pdata);
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-	imx27_add_imx_uart3(&uart_pdata);
-	imx27_add_imx_uart4(&uart_pdata);
-	imx27_add_imx_uart5(&uart_pdata);
-	imx27_add_mxc_nand(&mx27ads_nand_board_info);
-
-	/* only the i2c master 1 is used on this CPU card */
-	i2c_register_board_info(1, mx27ads_i2c_devices,
-				ARRAY_SIZE(mx27ads_i2c_devices));
-	imx27_add_imx_i2c(1, &mx27ads_i2c1_data);
-	imx27_add_imx_fb(&mx27ads_fb_data);
-
-	imx27_add_fec(NULL);
-	imx27_add_mxc_w1();
-}
-
-static void __init mx27ads_late_init(void)
-{
-	mx27ads_regulator_init();
-
-	imx27_add_mxc_mmc(0, &sdhc1_pdata);
-	imx27_add_mxc_mmc(1, &sdhc2_pdata);
-
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-}
-
-static void __init mx27ads_timer_init(void)
-{
-	unsigned long fref = 26000000;
-
-	if ((imx_readw(PBC_VERSION_REG) & CKIH_27MHZ_BIT_SET) == 0)
-		fref = 27000000;
-
-	mx27_clocks_init(fref);
-}
-
-static struct map_desc mx27ads_io_desc[] __initdata = {
-	{
-		.virtual = PBC_BASE_ADDRESS,
-		.pfn = __phys_to_pfn(MX27_CS4_BASE_ADDR),
-		.length = SZ_1M,
-		.type = MT_DEVICE,
-	},
-};
-
-static void __init mx27ads_map_io(void)
-{
-	mx27_map_io();
-	iotable_init(mx27ads_io_desc, ARRAY_SIZE(mx27ads_io_desc));
-}
-
-MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
-	/* maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx27ads_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= mx27ads_timer_init,
-	.init_machine = mx27ads_board_init,
-	.init_late	= mx27ads_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
deleted file mode 100644
index 23e63d3b4c6a..000000000000
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ /dev/null
@@ -1,615 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/delay.h>
-#include <linux/dma-mapping.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/machine.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static int mx31_3ds_pins[] = {
-	/* UART1 */
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-	IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO),
-	/*SPI0*/
-	IOMUX_MODE(MX31_PIN_DSR_DCE1, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_RI_DCE1, IOMUX_CONFIG_ALT1),
-	/* SPI 1 */
-	MX31_PIN_CSPI2_SCLK__SCLK,
-	MX31_PIN_CSPI2_MOSI__MOSI,
-	MX31_PIN_CSPI2_MISO__MISO,
-	MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI2_SS0__SS0,
-	MX31_PIN_CSPI2_SS2__SS2, /*CS for MC13783 */
-	/* MC13783 IRQ */
-	IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO),
-	/* USB OTG reset */
-	IOMUX_MODE(MX31_PIN_USB_PWR, IOMUX_CONFIG_GPIO),
-	/* USB OTG */
-	MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
-	MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
-	MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
-	MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
-	MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
-	MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
-	MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
-	MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
-	MX31_PIN_USBOTG_CLK__USBOTG_CLK,
-	MX31_PIN_USBOTG_DIR__USBOTG_DIR,
-	MX31_PIN_USBOTG_NXT__USBOTG_NXT,
-	MX31_PIN_USBOTG_STP__USBOTG_STP,
-	/*Keyboard*/
-	MX31_PIN_KEY_ROW0_KEY_ROW0,
-	MX31_PIN_KEY_ROW1_KEY_ROW1,
-	MX31_PIN_KEY_ROW2_KEY_ROW2,
-	MX31_PIN_KEY_COL0_KEY_COL0,
-	MX31_PIN_KEY_COL1_KEY_COL1,
-	MX31_PIN_KEY_COL2_KEY_COL2,
-	MX31_PIN_KEY_COL3_KEY_COL3,
-	/* USB Host 2 */
-	IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_PC_VS2, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_PC_BVD1, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_PC_BVD2, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_PC_RST, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_IOIS16, IOMUX_CONFIG_ALT1),
-	IOMUX_MODE(MX31_PIN_PC_RW_B, IOMUX_CONFIG_ALT1),
-	/* USB Host2 reset */
-	IOMUX_MODE(MX31_PIN_USB_BYP, IOMUX_CONFIG_GPIO),
-	/* I2C1 */
-	MX31_PIN_I2C_CLK__I2C1_SCL,
-	MX31_PIN_I2C_DAT__I2C1_SDA,
-	/* SDHC1 */
-	MX31_PIN_SD1_DATA3__SD1_DATA3,
-	MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA1__SD1_DATA1,
-	MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_CLK__SD1_CLK,
-	MX31_PIN_SD1_CMD__SD1_CMD,
-	MX31_PIN_GPIO3_1__GPIO3_1, /* Card detect */
-	MX31_PIN_GPIO3_0__GPIO3_0, /* OE */
-	/* Framebuffer */
-	MX31_PIN_LD0__LD0,
-	MX31_PIN_LD1__LD1,
-	MX31_PIN_LD2__LD2,
-	MX31_PIN_LD3__LD3,
-	MX31_PIN_LD4__LD4,
-	MX31_PIN_LD5__LD5,
-	MX31_PIN_LD6__LD6,
-	MX31_PIN_LD7__LD7,
-	MX31_PIN_LD8__LD8,
-	MX31_PIN_LD9__LD9,
-	MX31_PIN_LD10__LD10,
-	MX31_PIN_LD11__LD11,
-	MX31_PIN_LD12__LD12,
-	MX31_PIN_LD13__LD13,
-	MX31_PIN_LD14__LD14,
-	MX31_PIN_LD15__LD15,
-	MX31_PIN_LD16__LD16,
-	MX31_PIN_LD17__LD17,
-	MX31_PIN_VSYNC3__VSYNC3,
-	MX31_PIN_HSYNC__HSYNC,
-	MX31_PIN_FPSHIFT__FPSHIFT,
-	MX31_PIN_CONTRAST__CONTRAST,
-	/* SSI */
-	MX31_PIN_STXD4__STXD4,
-	MX31_PIN_SRXD4__SRXD4,
-	MX31_PIN_SCK4__SCK4,
-	MX31_PIN_SFS4__SFS4,
-};
-
-/*
- * FB support
- */
-static const struct fb_videomode fb_modedb[] = {
-	{	/* 480x640 @ 60 Hz */
-		.name		= "Epson-VGA",
-		.refresh	= 60,
-		.xres		= 480,
-		.yres		= 640,
-		.pixclock	= 41701,
-		.left_margin	= 20,
-		.right_margin	= 41,
-		.upper_margin	= 10,
-		.lower_margin	= 5,
-		.hsync_len	= 20,
-		.vsync_len	= 10,
-		.sync		= FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	},
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
-	.name		= "Epson-VGA",
-	.mode		= fb_modedb,
-	.num_modes	= ARRAY_SIZE(fb_modedb),
-};
-
-/* LCD */
-static struct gpiod_lookup_table mx31_3ds_lcd_gpiod_table = {
-	.dev_id = "spi0.2", /* Bus 0 chipselect 2 */
-	.table = {
-		/*
-		 * "reset" has IOMUX_TO_GPIO(IOMUX_PIN(88, 28)).
-		 * The macro only shifts 88 to bits 9..16 and then
-		 * mask it and shift it back. The GPIO number is 88.
-		 * 88 is 2*32+24
-		 */
-		GPIO_LOOKUP("imx31-gpio.2", 24, "reset", GPIO_ACTIVE_HIGH),
-		/*
-		 * Same reasoning as above for
-		 * IOMUX_TO_GPIO(IOMUX_PIN(89, 27), pin 89 is 2*32+25.
-		 */
-		GPIO_LOOKUP("imx31-gpio.2", 25, "enable", GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-/*
- * Support for SD card slot in personality board
- */
-#define MX31_3DS_GPIO_SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)
-#define MX31_3DS_GPIO_SDHC1_BE IOMUX_TO_GPIO(MX31_PIN_GPIO3_0)
-
-static struct gpio mx31_3ds_sdhc1_gpios[] = {
-	{ MX31_3DS_GPIO_SDHC1_CD, GPIOF_IN, "sdhc1-card-detect" },
-	{ MX31_3DS_GPIO_SDHC1_BE, GPIOF_OUT_INIT_LOW, "sdhc1-bus-en" },
-};
-
-static int mx31_3ds_sdhc1_init(struct device *dev,
-			       irq_handler_t detect_irq,
-			       void *data)
-{
-	int ret;
-
-	ret = gpio_request_array(mx31_3ds_sdhc1_gpios,
-				 ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
-	if (ret) {
-		pr_warn("Unable to request the SD/MMC GPIOs.\n");
-		return ret;
-	}
-
-	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)),
-			  detect_irq,
-			  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			  "sdhc1-detect", data);
-	if (ret) {
-		pr_warn("Unable to request the SD/MMC card-detect IRQ.\n");
-		goto gpio_free;
-	}
-
-	return 0;
-
-gpio_free:
-	gpio_free_array(mx31_3ds_sdhc1_gpios,
-			ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
-	return ret;
-}
-
-static void mx31_3ds_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)), data);
-	gpio_free_array(mx31_3ds_sdhc1_gpios,
-			 ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
-}
-
-static void mx31_3ds_sdhc1_setpower(struct device *dev, unsigned int vdd)
-{
-	/*
-	 * While the voltage stuff is done by the driver, activate the
-	 * Buffer Enable Pin only if there is a card in slot to fix the card
-	 * voltage issue caused by bi-directional chip TXB0108 on 3Stack.
-	 * Done here because at this stage we have for sure a debounced value
-	 * of the presence of the card, showed by the value of vdd.
-	 * 7 == ilog2(MMC_VDD_165_195)
-	 */
-	if (vdd > 7)
-		gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 1);
-	else
-		gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 0);
-}
-
-static struct imxmmc_platform_data sdhc1_pdata = {
-	.init		= mx31_3ds_sdhc1_init,
-	.exit		= mx31_3ds_sdhc1_exit,
-	.setpower	= mx31_3ds_sdhc1_setpower,
-};
-
-/*
- * Matrix keyboard
- */
-
-static const uint32_t mx31_3ds_keymap[] = {
-	KEY(0, 0, KEY_UP),
-	KEY(0, 1, KEY_DOWN),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_LEFT),
-	KEY(1, 2, KEY_ENTER),
-	KEY(2, 0, KEY_F6),
-	KEY(2, 1, KEY_F8),
-	KEY(2, 2, KEY_F9),
-	KEY(2, 3, KEY_F10),
-};
-
-static const struct matrix_keymap_data mx31_3ds_keymap_data __initconst = {
-	.keymap		= mx31_3ds_keymap,
-	.keymap_size	= ARRAY_SIZE(mx31_3ds_keymap),
-};
-
-/* Regulators */
-static struct regulator_init_data pwgtx_init = {
-	.constraints = {
-		.boot_on	= 1,
-		.always_on	= 1,
-	},
-};
-
-static struct regulator_init_data gpo_init = {
-	.constraints = {
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_consumer_supply vmmc2_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "imx31-mmc.0"),
-};
-
-static struct regulator_init_data vmmc2_init = {
-	.constraints = {
-		.min_uV = 3000000,
-		.max_uV = 3000000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vmmc2_consumers),
-	.consumer_supplies = vmmc2_consumers,
-};
-
-static struct regulator_consumer_supply vmmc1_consumers[] = {
-	REGULATOR_SUPPLY("vcore", "spi0.0"),
-};
-
-static struct regulator_init_data vmmc1_init = {
-	.constraints = {
-		.min_uV = 2800000,
-		.max_uV = 2800000,
-		.apply_uV = 1,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vmmc1_consumers),
-	.consumer_supplies = vmmc1_consumers,
-};
-
-static struct regulator_consumer_supply vgen_consumers[] = {
-	REGULATOR_SUPPLY("vdd", "spi0.0"),
-};
-
-static struct regulator_init_data vgen_init = {
-	.constraints = {
-		.min_uV = 1800000,
-		.max_uV = 1800000,
-		.apply_uV = 1,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vgen_consumers),
-	.consumer_supplies = vgen_consumers,
-};
-
-static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
-	{
-		.id = MC13783_REG_PWGT1SPI, /* Power Gate for ARM core. */
-		.init_data = &pwgtx_init,
-	}, {
-		.id = MC13783_REG_PWGT2SPI, /* Power Gate for L2 Cache. */
-		.init_data = &pwgtx_init,
-	}, {
-
-		.id = MC13783_REG_GPO1, /* Turn on 1.8V */
-		.init_data = &gpo_init,
-	}, {
-		.id = MC13783_REG_GPO3, /* Turn on 3.3V */
-		.init_data = &gpo_init,
-	}, {
-		.id = MC13783_REG_VMMC2, /* Power MMC/SD, WiFi/Bluetooth. */
-		.init_data = &vmmc2_init,
-	}, {
-		.id = MC13783_REG_VMMC1, /* Power LCD, CMOS, FM, GPS, Accel. */
-		.init_data = &vmmc1_init,
-	}, {
-		.id = MC13783_REG_VGEN,  /* Power LCD */
-		.init_data = &vgen_init,
-	},
-};
-
-/* MC13783 */
-static struct mc13xxx_codec_platform_data mx31_3ds_codec = {
-	.dac_ssi_port = MC13783_SSI1_PORT,
-	.adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data mc13783_pdata = {
-	.regulators = {
-		.regulators = mx31_3ds_regulators,
-		.num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
-	},
-	.codec = &mx31_3ds_codec,
-	.flags  = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC | MC13XXX_USE_CODEC,
-
-};
-
-static struct imx_ssi_platform_data mx31_3ds_ssi_pdata = {
-	.flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-static struct spi_board_info mx31_3ds_spi_devs[] __initdata = {
-	{
-		.modalias	= "mc13783",
-		.max_speed_hz	= 1000000,
-		.bus_num	= 1,
-		.chip_select	= 2, /* SS2 */
-		.platform_data	= &mc13783_pdata,
-		/* irq number is run-time assigned */
-		.mode = SPI_CS_HIGH,
-	}, {
-		.modalias	= "l4f00242t03",
-		.max_speed_hz	= 5000000,
-		.bus_num	= 0,
-		.chip_select	= 2, /* SS2 */
-	},
-};
-
-/*
- * NAND Flash
- */
-static const struct mxc_nand_platform_data
-mx31_3ds_nand_board_info __initconst = {
-	.width		= 1,
-	.hw_ecc		= 1,
-#ifdef CONFIG_MACH_MX31_3DS_MXC_NAND_USE_BBT
-	.flash_bbt	= 1,
-#endif
-};
-
-/*
- * USB OTG
- */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-		     PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-#define USBOTG_RST_B IOMUX_TO_GPIO(MX31_PIN_USB_PWR)
-#define USBH2_RST_B IOMUX_TO_GPIO(MX31_PIN_USB_BYP)
-
-static int mx31_3ds_usbotg_init(void)
-{
-	int err;
-
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
-
-	err = gpio_request(USBOTG_RST_B, "otgusb-reset");
-	if (err) {
-		pr_err("Failed to request the USB OTG reset gpio\n");
-		return err;
-	}
-
-	err = gpio_direction_output(USBOTG_RST_B, 0);
-	if (err) {
-		pr_err("Failed to drive the USB OTG reset gpio\n");
-		goto usbotg_free_reset;
-	}
-
-	mdelay(1);
-	gpio_set_value(USBOTG_RST_B, 1);
-	return 0;
-
-usbotg_free_reset:
-	gpio_free(USBOTG_RST_B);
-	return err;
-}
-
-static int mx31_3ds_otg_init(struct platform_device *pdev)
-{
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static int mx31_3ds_host2_init(struct platform_device *pdev)
-{
-	int err;
-
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_PC_VS2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_PC_BVD1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_PC_BVD2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_PC_RST, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_IOIS16, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_PC_RW_B, USB_PAD_CFG);
-
-	err = gpio_request(USBH2_RST_B, "usbh2-reset");
-	if (err) {
-		pr_err("Failed to request the USB Host 2 reset gpio\n");
-		return err;
-	}
-
-	err = gpio_direction_output(USBH2_RST_B, 0);
-	if (err) {
-		pr_err("Failed to drive the USB Host 2 reset gpio\n");
-		goto usbotg_free_reset;
-	}
-
-	mdelay(1);
-	gpio_set_value(USBH2_RST_B, 1);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-
-usbotg_free_reset:
-	gpio_free(USBH2_RST_B);
-	return err;
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= mx31_3ds_otg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init = mx31_3ds_host2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data usbotg_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx31_3ds_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", mx31_3ds_otg_mode);
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data mx31_3ds_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-static void __init mx31_3ds_init(void)
-{
-	imx31_soc_init();
-
-	/* Configure SPI1 IOMUX */
-	mxc_iomux_set_gpr(MUX_PGP_CSPI_BB, true);
-
-	mxc_iomux_setup_multiple_pins(mx31_3ds_pins, ARRAY_SIZE(mx31_3ds_pins),
-				      "mx31_3ds");
-
-	imx31_add_imx_uart0(&uart_pdata);
-	imx31_add_mxc_nand(&mx31_3ds_nand_board_info);
-
-	imx31_add_spi_imx1(NULL);
-
-	imx31_add_imx_keypad(&mx31_3ds_keymap_data);
-
-	imx31_add_imx2_wdt();
-	imx31_add_imx_i2c0(&mx31_3ds_i2c0_data);
-
-	imx31_add_spi_imx0(NULL);
-	imx31_add_ipu_core();
-	imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
-	imx31_add_imx_ssi(0, &mx31_3ds_ssi_pdata);
-
-	imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-}
-
-static void __init mx31_3ds_late(void)
-{
-	gpiod_add_lookup_table(&mx31_3ds_lcd_gpiod_table);
-	mx31_3ds_spi_devs[0].irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-	spi_register_board_info(mx31_3ds_spi_devs,
-				ARRAY_SIZE(mx31_3ds_spi_devs));
-
-	mx31_3ds_usbotg_init();
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-		if (otg_pdata.otg)
-			imx31_add_mxc_ehci_otg(&otg_pdata);
-	}
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	if (!otg_mode_host)
-		imx31_add_fsl_usb2_udc(&usbotg_pdata);
-
-	if (mxc_expio_init(MX31_CS5_BASE_ADDR, IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)))
-		printk(KERN_WARNING "Init of the debug board failed, all "
-		       "devices on the debug board are unusable.\n");
-
-	imx31_add_mxc_mmc(0, &sdhc1_pdata);
-}
-
-static void __init mx31_3ds_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
-	/* Maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= mx31_3ds_timer_init,
-	.init_machine = mx31_3ds_init,
-	.init_late	= mx31_3ds_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c
deleted file mode 100644
index 49783385bccf..000000000000
--- a/arch/arm/mach-imx/mach-mx31ads.c
+++ /dev/null
@@ -1,579 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/serial_8250.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-#include <linux/mfd/wm8350/audio.h>
-#include <linux/mfd/wm8350/core.h>
-#include <linux/mfd/wm8350/pmic.h>
-#endif
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/* Base address of PBC controller */
-#define PBC_BASE_ADDRESS	MX31_CS4_BASE_ADDR_VIRT
-
-/* PBC Board interrupt status register */
-#define PBC_INTSTATUS           0x000016
-
-/* PBC Board interrupt current status register */
-#define PBC_INTCURR_STATUS      0x000018
-
-/* PBC Interrupt mask register set address */
-#define PBC_INTMASK_SET         0x00001A
-
-/* PBC Interrupt mask register clear address */
-#define PBC_INTMASK_CLEAR       0x00001C
-
-/* External UART A */
-#define PBC_SC16C652_UARTA      0x010000
-
-/* External UART B */
-#define PBC_SC16C652_UARTB      0x010010
-
-#define PBC_INTSTATUS_REG	(PBC_INTSTATUS + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_SET_REG	(PBC_INTMASK_SET + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_CLEAR_REG	(PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
-
-#define EXPIO_INT_XUART_INTA	10
-#define EXPIO_INT_XUART_INTB	11
-
-#define MXC_MAX_EXP_IO_LINES	16
-
-/* CS8900 */
-#define EXPIO_INT_ENET_INT	8
-#define CS4_CS8900_MMIO_START	0x20000
-
-static struct irq_domain *domain;
-
-/*
- * The serial port definition structure.
- */
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
-		.mapbase  = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTA),
-		.uartclk  = 14745600,
-		.regshift = 0,
-		.iotype   = UPIO_MEM,
-		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
-	}, {
-		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
-		.mapbase  = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTB),
-		.uartclk  = 14745600,
-		.regshift = 0,
-		.iotype   = UPIO_MEM,
-		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
-	},
-	{},
-};
-
-static struct platform_device serial_device = {
-	.name	= "serial8250",
-	.id	= 0,
-	.dev	= {
-		.platform_data = serial_platform_data,
-	},
-};
-
-static struct resource mx31ads_cs8900_resources[] __initdata = {
-	DEFINE_RES_MEM(MX31_CS4_BASE_ADDR + CS4_CS8900_MMIO_START, SZ_64K),
-	DEFINE_RES_IRQ(-1),
-};
-
-static const struct platform_device_info mx31ads_cs8900_devinfo __initconst = {
-	.name = "cs89x0",
-	.id = 0,
-	.res = mx31ads_cs8900_resources,
-	.num_res = ARRAY_SIZE(mx31ads_cs8900_resources),
-};
-
-static int __init mxc_init_extuart(void)
-{
-	serial_platform_data[0].irq = irq_find_mapping(domain,
-						       EXPIO_INT_XUART_INTA);
-	serial_platform_data[1].irq = irq_find_mapping(domain,
-						       EXPIO_INT_XUART_INTB);
-	return platform_device_register(&serial_device);
-}
-
-static void __init mxc_init_ext_ethernet(void)
-{
-	mx31ads_cs8900_resources[1].start =
-			irq_find_mapping(domain, EXPIO_INT_ENET_INT);
-	mx31ads_cs8900_resources[1].end =
-			irq_find_mapping(domain, EXPIO_INT_ENET_INT);
-	platform_device_register_full(
-		(struct platform_device_info *)&mx31ads_cs8900_devinfo);
-}
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static unsigned int uart_pins[] = {
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1
-};
-
-static inline void mxc_init_imx_uart(void)
-{
-	mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
-	imx31_add_imx_uart0(&uart_pdata);
-}
-
-static void mx31ads_expio_irq_handler(struct irq_desc *desc)
-{
-	u32 imr_val;
-	u32 int_valid;
-	u32 expio_irq;
-
-	imr_val = imx_readw(PBC_INTMASK_SET_REG);
-	int_valid = imx_readw(PBC_INTSTATUS_REG) & imr_val;
-
-	expio_irq = 0;
-	for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
-		if ((int_valid & 1) == 0)
-			continue;
-
-		generic_handle_irq(irq_find_mapping(domain, expio_irq));
-	}
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * @param d	an expio virtual irq description
- */
-static void expio_mask_irq(struct irq_data *d)
-{
-	u32 expio = d->hwirq;
-	/* mask the interrupt */
-	imx_writew(1 << expio, PBC_INTMASK_CLEAR_REG);
-	imx_readw(PBC_INTMASK_CLEAR_REG);
-}
-
-/*
- * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
- * @param d	an expio virtual irq description
- */
-static void expio_ack_irq(struct irq_data *d)
-{
-	u32 expio = d->hwirq;
-	/* clear the interrupt status */
-	imx_writew(1 << expio, PBC_INTSTATUS_REG);
-}
-
-/*
- * Enable a expio pin's interrupt by clearing the bit in the imr.
- * @param d	an expio virtual irq description
- */
-static void expio_unmask_irq(struct irq_data *d)
-{
-	u32 expio = d->hwirq;
-	/* unmask the interrupt */
-	imx_writew(1 << expio, PBC_INTMASK_SET_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
-	.name = "EXPIO(CPLD)",
-	.irq_ack = expio_ack_irq,
-	.irq_mask = expio_mask_irq,
-	.irq_unmask = expio_unmask_irq,
-};
-
-static void __init mx31ads_init_expio(void)
-{
-	int irq_base;
-	int i, irq;
-
-	printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");
-
-	/*
-	 * Configure INT line as GPIO input
-	 */
-	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");
-
-	/* disable the interrupt and clear the status */
-	imx_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
-	imx_writew(0xFFFF, PBC_INTSTATUS_REG);
-
-	irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
-	WARN_ON(irq_base < 0);
-
-	domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
-				       &irq_domain_simple_ops, NULL);
-	WARN_ON(!domain);
-
-	for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
-		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
-		irq_clear_status_flags(i, IRQ_NOREQUEST);
-	}
-	irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
-	irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);
-	irq_set_chained_handler(irq, mx31ads_expio_irq_handler);
-}
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-/* This section defines setup for the Wolfson Microelectronics
- * 1133-EV1 PMU/audio board.  When other PMU boards are supported the
- * regulator definitions may be shared with them, but for now they can
- * only be used with this board so would generate warnings about
- * unused statics and some of the configuration is specific to this
- * module.
- */
-
-/* CPU */
-static struct regulator_consumer_supply sw1a_consumers[] = {
-	{
-		.supply = "cpu_vcc",
-	}
-};
-
-static struct regulator_init_data sw1a_data = {
-	.constraints = {
-		.name = "SW1A",
-		.min_uV = 1275000,
-		.max_uV = 1600000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_MODE,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-				    REGULATOR_MODE_FAST,
-		.state_mem = {
-			 .uV = 1400000,
-			 .mode = REGULATOR_MODE_NORMAL,
-			 .enabled = 1,
-		 },
-		.initial_state = PM_SUSPEND_MEM,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sw1a_consumers),
-	.consumer_supplies = sw1a_consumers,
-};
-
-/* System IO - High */
-static struct regulator_init_data viohi_data = {
-	.constraints = {
-		.name = "VIOHO",
-		.min_uV = 2800000,
-		.max_uV = 2800000,
-		.state_mem = {
-			 .uV = 2800000,
-			 .mode = REGULATOR_MODE_NORMAL,
-			 .enabled = 1,
-		 },
-		.initial_state = PM_SUSPEND_MEM,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-};
-
-/* System IO - Low */
-static struct regulator_init_data violo_data = {
-	.constraints = {
-		.name = "VIOLO",
-		.min_uV = 1800000,
-		.max_uV = 1800000,
-		.state_mem = {
-			 .uV = 1800000,
-			 .mode = REGULATOR_MODE_NORMAL,
-			 .enabled = 1,
-		 },
-		.initial_state = PM_SUSPEND_MEM,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-};
-
-/* DDR RAM */
-static struct regulator_init_data sw2a_data = {
-	.constraints = {
-		.name = "SW2A",
-		.min_uV = 1800000,
-		.max_uV = 1800000,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL,
-		.state_mem = {
-			 .uV = 1800000,
-			 .mode = REGULATOR_MODE_NORMAL,
-			 .enabled = 1,
-		 },
-		.state_disk = {
-			 .mode = REGULATOR_MODE_NORMAL,
-			 .enabled = 0,
-		 },
-		.always_on = 1,
-		.boot_on = 1,
-		.initial_state = PM_SUSPEND_MEM,
-	},
-};
-
-static struct regulator_init_data ldo1_data = {
-	.constraints = {
-		.name = "VCAM/VMMC1/VMMC2",
-		.min_uV = 2800000,
-		.max_uV = 2800000,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL,
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		.apply_uV = 1,
-	},
-};
-
-static struct regulator_consumer_supply ldo2_consumers[] = {
-	{ .supply = "AVDD", .dev_name = "1-001a" },
-	{ .supply = "HPVDD", .dev_name = "1-001a" },
-};
-
-/* CODEC and SIM */
-static struct regulator_init_data ldo2_data = {
-	.constraints = {
-		.name = "VESIM/VSIM/AVDD",
-		.min_uV = 3300000,
-		.max_uV = 3300000,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL,
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		.apply_uV = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
-	.consumer_supplies = ldo2_consumers,
-};
-
-/* General */
-static struct regulator_init_data vdig_data = {
-	.constraints = {
-		.name = "VDIG",
-		.min_uV = 1500000,
-		.max_uV = 1500000,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL,
-		.apply_uV = 1,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-};
-
-/* Tranceivers */
-static struct regulator_init_data ldo4_data = {
-	.constraints = {
-		.name = "VRF1/CVDD_2.775",
-		.min_uV = 2500000,
-		.max_uV = 2500000,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL,
-		.apply_uV = 1,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-};
-
-static struct wm8350_led_platform_data wm8350_led_data = {
-	.name            = "wm8350:white",
-	.default_trigger = "heartbeat",
-	.max_uA          = 27899,
-};
-
-static struct wm8350_audio_platform_data imx32ads_wm8350_setup = {
-	.vmid_discharge_msecs = 1000,
-	.drain_msecs = 30,
-	.cap_discharge_msecs = 700,
-	.vmid_charge_msecs = 700,
-	.vmid_s_curve = WM8350_S_CURVE_SLOW,
-	.dis_out4 = WM8350_DISCHARGE_SLOW,
-	.dis_out3 = WM8350_DISCHARGE_SLOW,
-	.dis_out2 = WM8350_DISCHARGE_SLOW,
-	.dis_out1 = WM8350_DISCHARGE_SLOW,
-	.vroi_out4 = WM8350_TIE_OFF_500R,
-	.vroi_out3 = WM8350_TIE_OFF_500R,
-	.vroi_out2 = WM8350_TIE_OFF_500R,
-	.vroi_out1 = WM8350_TIE_OFF_500R,
-	.vroi_enable = 0,
-	.codec_current_on = WM8350_CODEC_ISEL_1_0,
-	.codec_current_standby = WM8350_CODEC_ISEL_0_5,
-	.codec_current_charge = WM8350_CODEC_ISEL_1_5,
-};
-
-static int mx31_wm8350_init(struct wm8350 *wm8350)
-{
-	wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN,
-			   WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW,
-			   WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_ON);
-
-	wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN,
-			   WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH,
-			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_ON);
-
-	wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN,
-			   WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH,
-			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_OFF);
-
-	wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN,
-			   WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH,
-			   WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_OFF);
-
-	wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT,
-			   WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH,
-			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_OFF);
-
-	wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT,
-			   WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
-			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_OFF);
-
-	wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT,
-			   WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
-			   WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
-			   WM8350_GPIO_DEBOUNCE_OFF);
-
-	wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data);
-	wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data);
-	wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data);
-	wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data);
-	wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data);
-	wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data);
-	wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data);
-	wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data);
-
-	/* LEDs */
-	wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1,
-			     WM8350_DC5_ERRACT_SHUTDOWN_CONV);
-	wm8350_isink_set_flash(wm8350, WM8350_ISINK_A,
-			       WM8350_ISINK_FLASH_DISABLE,
-			       WM8350_ISINK_FLASH_TRIG_BIT,
-			       WM8350_ISINK_FLASH_DUR_32MS,
-			       WM8350_ISINK_FLASH_ON_INSTANT,
-			       WM8350_ISINK_FLASH_OFF_INSTANT,
-			       WM8350_ISINK_FLASH_MODE_EN);
-	wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5,
-			       WM8350_ISINK_MODE_BOOST,
-			       WM8350_ISINK_ILIM_NORMAL,
-			       WM8350_DC5_RMP_20V,
-			       WM8350_DC5_FBSRC_ISINKA);
-	wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A,
-			    &wm8350_led_data);
-
-	wm8350->codec.platform_data = &imx32ads_wm8350_setup;
-
-	regulator_has_full_constraints();
-
-	return 0;
-}
-
-static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
-	.init = mx31_wm8350_init,
-};
-#endif
-
-static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-	{
-		I2C_BOARD_INFO("wm8350", 0x1a),
-		.platform_data = &mx31_wm8350_pdata,
-		/* irq number is run-time assigned */
-	},
-#endif
-};
-
-static void __init mxc_init_i2c(void)
-{
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-	mx31ads_i2c1_devices[0].irq =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-#endif
-	i2c_register_board_info(1, mx31ads_i2c1_devices,
-				ARRAY_SIZE(mx31ads_i2c1_devices));
-
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));
-
-	imx31_add_imx_i2c1(NULL);
-}
-
-static unsigned int ssi_pins[] = {
-	MX31_PIN_SFS5__SFS5,
-	MX31_PIN_SCK5__SCK5,
-	MX31_PIN_SRXD5__SRXD5,
-	MX31_PIN_STXD5__STXD5,
-};
-
-static void __init mxc_init_audio(void)
-{
-	imx31_add_imx_ssi(0, NULL);
-	mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
-}
-
-/*
- * Static mappings, starting from the CS4 start address up to the start address
- * of the CS8900.
- */
-static struct map_desc mx31ads_io_desc[] __initdata = {
-	{
-		.virtual	= (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
-		.pfn		= __phys_to_pfn(MX31_CS4_BASE_ADDR),
-		.length		= CS4_CS8900_MMIO_START,
-		.type		= MT_DEVICE
-	},
-};
-
-static void __init mx31ads_map_io(void)
-{
-	mx31_map_io();
-	iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
-}
-
-static void __init mx31ads_init(void)
-{
-	imx31_soc_init();
-
-	mxc_init_imx_uart();
-	mxc_init_audio();
-}
-
-static void __init mx31ads_late(void)
-{
-	mx31ads_init_expio();
-	mxc_init_extuart();
-	mxc_init_i2c();
-	mxc_init_ext_ethernet();
-}
-
-static void __init mx31ads_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31ADS, "Freescale MX31ADS")
-	/* Maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx31ads_map_io,
-	.init_early = imx31_init_early,
-	.init_irq	= mx31_init_irq,
-	.init_time	= mx31ads_timer_init,
-	.init_machine = mx31ads_init,
-	.init_late	= mx31ads_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c
deleted file mode 100644
index 4b955ccc92cd..000000000000
--- a/arch/arm/mach-imx/mach-mx31lilly.c
+++ /dev/null
@@ -1,312 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  LILLY-1131 module support
- *
- *    Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- *  based on code for other MX31 boards,
- *
- *    Copyright 2005-2007 Freescale Semiconductor
- *    Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- *    Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/moduleparam.h>
-#include <linux/smsc911x.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lilly.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-/*
- * This file contains module-specific initialization routines for LILLY-1131.
- * Initialization of peripherals found on the baseboard is implemented in the
- * appropriate baseboard support code.
- */
-
-static unsigned int mx31lilly_pins[] __initdata = {
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-	MX31_PIN_CTS2__CTS2,
-	MX31_PIN_RTS2__RTS2,
-	MX31_PIN_TXD2__TXD2,
-	MX31_PIN_RXD2__RXD2,
-	MX31_PIN_CSPI3_MOSI__RXD3,
-	MX31_PIN_CSPI3_MISO__TXD3,
-	MX31_PIN_CSPI3_SCLK__RTS3,
-	MX31_PIN_CSPI3_SPI_RDY__CTS3,
-};
-
-/* UART */
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-/* SMSC ethernet support */
-
-static struct resource smsc91x_resources[] = {
-	{
-		.start	= MX31_CS4_BASE_ADDR,
-		.end	= MX31_CS4_BASE_ADDR + 0xffff,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		/* irq number is run-time assigned */
-		.flags	= IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
-	}
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
-	.flags		= SMSC911X_USE_32BIT |
-			  SMSC911X_SAVE_MAC_ADDRESS |
-			  SMSC911X_FORCE_INTERNAL_PHY,
-};
-
-static struct platform_device smsc91x_device = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(smsc91x_resources),
-	.resource	= smsc91x_resources,
-	.dev		= {
-		.platform_data = &smsc911x_config,
-	}
-};
-
-/* NOR flash */
-static struct physmap_flash_data nor_flash_data = {
-	.width  = 2,
-};
-
-static struct resource nor_flash_resource = {
-	.start	= 0xa0000000,
-	.end	= 0xa1ffffff,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device physmap_flash_device = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &nor_flash_data,
-	},
-	.resource = &nor_flash_resource,
-	.num_resources = 1,
-};
-
-/* USB */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbh1_init(struct platform_device *pdev)
-{
-	int pins[] = {
-		MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
-		MX31_PIN_CSPI1_MISO__USBH1_RXDP,
-		MX31_PIN_CSPI1_SS0__USBH1_TXDM,
-		MX31_PIN_CSPI1_SS1__USBH1_TXDP,
-		MX31_PIN_CSPI1_SS2__USBH1_RCV,
-		MX31_PIN_CSPI1_SCLK__USBH1_OEB,
-		MX31_PIN_CSPI1_SPI_RDY__USBH1_FS,
-	};
-
-	mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H1");
-
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
-
-	mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-static int usbh2_init(struct platform_device *pdev)
-{
-	int pins[] = {
-		MX31_PIN_USBH2_DATA0__USBH2_DATA0,
-		MX31_PIN_USBH2_DATA1__USBH2_DATA1,
-		MX31_PIN_USBH2_CLK__USBH2_CLK,
-		MX31_PIN_USBH2_DIR__USBH2_DIR,
-		MX31_PIN_USBH2_NXT__USBH2_NXT,
-		MX31_PIN_USBH2_STP__USBH2_STP,
-	};
-
-	mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");
-
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
-	mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
-	/* chip select */
-	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
-				"USBH2_CS");
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
-	gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
-	.init	= usbh1_init,
-	.portsc	= MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static void __init lilly1131_usb_init(void)
-{
-	imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
-	.flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static struct spi_board_info mc13783_dev __initdata = {
-	.modalias	= "mc13783",
-	.max_speed_hz	= 1000000,
-	.bus_num	= 1,
-	.chip_select	= 0,
-	.platform_data	= &mc13783_pdata,
-	/* irq number is run-time assigned */
-};
-
-static struct platform_device *devices[] __initdata = {
-	&smsc91x_device,
-	&physmap_flash_device,
-};
-
-static int mx31lilly_baseboard;
-core_param(mx31lilly_baseboard, mx31lilly_baseboard, int, 0444);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static void __init mx31lilly_board_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(mx31lilly_pins,
-				      ARRAY_SIZE(mx31lilly_pins), "mx31lily");
-
-	imx31_add_imx_uart0(&uart_pdata);
-	imx31_add_imx_uart1(&uart_pdata);
-	imx31_add_imx_uart2(&uart_pdata);
-
-	mxc_iomux_alloc_pin(MX31_PIN_CS4__CS4, "Ethernet CS");
-
-	/* SPI */
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SCLK__SCLK, "SPI1_CLK");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MOSI__MOSI, "SPI1_TX");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MISO__MISO, "SPI1_RX");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, "SPI1_RDY");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS0__SS0, "SPI1_SS0");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS1__SS1, "SPI1_SS1");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS2__SS2, "SPI1_SS2");
-
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SCLK__SCLK, "SPI2_CLK");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MOSI__MOSI, "SPI2_TX");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MISO__MISO, "SPI2_RX");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SPI_RDY__SPI_RDY, "SPI2_RDY");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS0__SS0, "SPI2_SS0");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS1__SS1, "SPI2_SS1");
-	mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS2__SS2, "SPI2_SS2");
-
-	imx31_add_spi_imx0(NULL);
-	imx31_add_spi_imx1(NULL);
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-}
-
-static void __init mx31lilly_late_init(void)
-{
-	if (mx31lilly_baseboard == MX31LILLY_DB)
-		mx31lilly_db_init();
-
-	mc13783_dev.irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-	spi_register_board_info(&mc13783_dev, 1);
-
-	smsc91x_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
-	smsc91x_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_0));
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	/* USB */
-	lilly1131_usb_init();
-}
-
-static void __init mx31lilly_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(LILLY1131, "INCO startec LILLY-1131")
-	.atag_offset = 0x100,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= mx31lilly_timer_init,
-	.init_machine	= mx31lilly_board_init,
-	.init_late	= mx31lilly_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31lite.c b/arch/arm/mach-imx/mach-mx31lite.c
deleted file mode 100644
index aaccf52f7ac1..000000000000
--- a/arch/arm/mach-imx/mach-mx31lite.c
+++ /dev/null
@@ -1,290 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- *  Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/memory.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/moduleparam.h>
-#include <linux/smsc911x.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/mtd/physmap.h>
-#include <linux/delay.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/page.h>
-#include <asm/setup.h>
-
-#include "board-mx31lite.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-/*
- * This file contains the module-specific initialization routines.
- */
-
-static unsigned int mx31lite_pins[] = {
-	/* UART1 */
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-	/* SPI 0 */
-	MX31_PIN_CSPI1_SCLK__SCLK,
-	MX31_PIN_CSPI1_MOSI__MOSI,
-	MX31_PIN_CSPI1_MISO__MISO,
-	MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI1_SS0__SS0,
-	MX31_PIN_CSPI1_SS1__SS1,
-	MX31_PIN_CSPI1_SS2__SS2,
-	/* LAN9117 IRQ pin */
-	IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO),
-	/* SPI 1 */
-	MX31_PIN_CSPI2_SCLK__SCLK,
-	MX31_PIN_CSPI2_MOSI__MOSI,
-	MX31_PIN_CSPI2_MISO__MISO,
-	MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI2_SS0__SS0,
-	MX31_PIN_CSPI2_SS1__SS1,
-	MX31_PIN_CSPI2_SS2__SS2,
-};
-
-/* UART */
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-mx31lite_nand_board_info __initconst  = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
-	.flags		= SMSC911X_USE_16BIT,
-};
-
-static struct resource smsc911x_resources[] = {
-	{
-		.start		= MX31_CS4_BASE_ADDR,
-		.end		= MX31_CS4_BASE_ADDR + 0x100,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device smsc911x_device = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(smsc911x_resources),
-	.resource	= smsc911x_resources,
-	.dev		= {
-		.platform_data = &smsc911x_config,
-	},
-};
-
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
-	.flags = MC13XXX_USE_RTC,
-};
-
-static struct spi_board_info mc13783_spi_dev __initdata = {
-	.modalias       = "mc13783",
-	.max_speed_hz   = 1000000,
-	.bus_num	= 1,
-	.chip_select    = 0,
-	.platform_data  = &mc13783_pdata,
-	/* irq number is run-time assigned */
-};
-
-/*
- * USB
- */
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int usbh2_init(struct platform_device *pdev)
-{
-	int pins[] = {
-		MX31_PIN_USBH2_DATA0__USBH2_DATA0,
-		MX31_PIN_USBH2_DATA1__USBH2_DATA1,
-		MX31_PIN_USBH2_CLK__USBH2_CLK,
-		MX31_PIN_USBH2_DIR__USBH2_DIR,
-		MX31_PIN_USBH2_NXT__USBH2_NXT,
-		MX31_PIN_USBH2_STP__USBH2_STP,
-	};
-
-	mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");
-
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
-
-	mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-
-	/* chip select */
-	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
-				"USBH2_CS");
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
-	gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init   = usbh2_init,
-	.portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-/*
- * NOR flash
- */
-
-static struct physmap_flash_data nor_flash_data = {
-	.width  = 2,
-};
-
-static struct resource nor_flash_resource = {
-	.start  = 0xa0000000,
-	.end    = 0xa1ffffff,
-	.flags  = IORESOURCE_MEM,
-};
-
-static struct platform_device physmap_flash_device = {
-	.name   = "physmap-flash",
-	.id     = 0,
-	.dev    = {
-		.platform_data  = &nor_flash_data,
-	},
-	.resource = &nor_flash_resource,
-	.num_resources = 1,
-};
-
-/*
- * This structure defines the MX31 memory map.
- */
-static struct map_desc mx31lite_io_desc[] __initdata = {
-	{
-		.virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
-		.pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
-		.length = MX31_CS4_SIZE,
-		.type = MT_DEVICE
-	}
-};
-
-/*
- * Set up static virtual mappings.
- */
-static void __init mx31lite_map_io(void)
-{
-	mx31_map_io();
-	iotable_init(mx31lite_io_desc, ARRAY_SIZE(mx31lite_io_desc));
-}
-
-static int mx31lite_baseboard;
-core_param(mx31lite_baseboard, mx31lite_baseboard, int, 0444);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-static void __init mx31lite_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(mx31lite_pins, ARRAY_SIZE(mx31lite_pins),
-				      "mx31lite");
-
-	imx31_add_imx_uart0(&uart_pdata);
-	imx31_add_spi_imx0(NULL);
-
-	/* NOR and NAND flash */
-	platform_device_register(&physmap_flash_device);
-	imx31_add_mxc_nand(&mx31lite_nand_board_info);
-
-	imx31_add_spi_imx1(NULL);
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-}
-
-static void __init mx31lite_late(void)
-{
-	int ret;
-
-	if (mx31lite_baseboard == MX31LITE_DB)
-		mx31lite_db_init();
-
-	mc13783_spi_dev.irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-	spi_register_board_info(&mc13783_spi_dev, 1);
-
-	/* USB */
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	/* SMSC9117 IRQ pin */
-	ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_SFS6), "sms9117-irq");
-	if (ret)
-		pr_warn("could not get LAN irq gpio\n");
-	else {
-		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_SFS6));
-		smsc911x_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
-		smsc911x_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
-		platform_device_register(&smsc911x_device);
-	}
-}
-
-static void __init mx31lite_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
-	/* Maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx31lite_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= mx31lite_timer_init,
-	.init_machine = mx31lite_init,
-	.init_late	= mx31lite_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
deleted file mode 100644
index 7f780ad2d459..000000000000
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ /dev/null
@@ -1,581 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2008 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/dma-map-ops.h>
-#include <linux/gfp.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/moduleparam.h>
-#include <linux/leds.h>
-#include <linux/memory.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/machine.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/types.h>
-#include <linux/memblock.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/err.h>
-#include <linux/input.h>
-
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/memblock.h>
-#include <linux/platform_data/asoc-imx-ssi.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int moboard_pins[] = {
-	/* UART0 */
-	MX31_PIN_TXD1__TXD1, MX31_PIN_RXD1__RXD1,
-	MX31_PIN_CTS1__GPIO2_7,
-	/* UART4 */
-	MX31_PIN_PC_RST__CTS5, MX31_PIN_PC_VS2__RTS5,
-	MX31_PIN_PC_BVD2__TXD5, MX31_PIN_PC_BVD1__RXD5,
-	/* I2C0 */
-	MX31_PIN_I2C_DAT__I2C1_SDA, MX31_PIN_I2C_CLK__I2C1_SCL,
-	/* I2C1 */
-	MX31_PIN_DCD_DTE1__I2C2_SDA, MX31_PIN_RI_DTE1__I2C2_SCL,
-	/* SDHC1 */
-	MX31_PIN_SD1_DATA3__SD1_DATA3, MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA1__SD1_DATA1, MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_CLK__SD1_CLK, MX31_PIN_SD1_CMD__SD1_CMD,
-	MX31_PIN_ATA_CS0__GPIO3_26, MX31_PIN_ATA_CS1__GPIO3_27,
-	/* USB reset */
-	MX31_PIN_GPIO1_0__GPIO1_0,
-	/* USB OTG */
-	MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
-	MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
-	MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
-	MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
-	MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
-	MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
-	MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
-	MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
-	MX31_PIN_USBOTG_CLK__USBOTG_CLK, MX31_PIN_USBOTG_DIR__USBOTG_DIR,
-	MX31_PIN_USBOTG_NXT__USBOTG_NXT, MX31_PIN_USBOTG_STP__USBOTG_STP,
-	MX31_PIN_USB_OC__GPIO1_30,
-	/* USB H2 */
-	MX31_PIN_USBH2_DATA0__USBH2_DATA0,
-	MX31_PIN_USBH2_DATA1__USBH2_DATA1,
-	MX31_PIN_STXD3__USBH2_DATA2, MX31_PIN_SRXD3__USBH2_DATA3,
-	MX31_PIN_SCK3__USBH2_DATA4, MX31_PIN_SFS3__USBH2_DATA5,
-	MX31_PIN_STXD6__USBH2_DATA6, MX31_PIN_SRXD6__USBH2_DATA7,
-	MX31_PIN_USBH2_CLK__USBH2_CLK, MX31_PIN_USBH2_DIR__USBH2_DIR,
-	MX31_PIN_USBH2_NXT__USBH2_NXT, MX31_PIN_USBH2_STP__USBH2_STP,
-	MX31_PIN_SCK6__GPIO1_25,
-	/* LEDs */
-	MX31_PIN_SVEN0__GPIO2_0, MX31_PIN_STX0__GPIO2_1,
-	MX31_PIN_SRX0__GPIO2_2, MX31_PIN_SIMPD0__GPIO2_3,
-	/* SPI1 */
-	MX31_PIN_CSPI2_MOSI__MOSI, MX31_PIN_CSPI2_MISO__MISO,
-	MX31_PIN_CSPI2_SCLK__SCLK, MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI2_SS0__SS0, MX31_PIN_CSPI2_SS2__SS2,
-	/* Atlas IRQ */
-	MX31_PIN_GPIO1_3__GPIO1_3,
-	/* SPI2 */
-	MX31_PIN_CSPI3_MOSI__MOSI, MX31_PIN_CSPI3_MISO__MISO,
-	MX31_PIN_CSPI3_SCLK__SCLK, MX31_PIN_CSPI3_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI2_SS1__CSPI3_SS1,
-	/* SSI */
-	MX31_PIN_STXD4__STXD4, MX31_PIN_SRXD4__SRXD4,
-	MX31_PIN_SCK4__SCK4, MX31_PIN_SFS4__SFS4,
-};
-
-static struct physmap_flash_data mx31moboard_flash_data = {
-	.width	= 2,
-};
-
-static struct resource mx31moboard_flash_resource = {
-	.start	= 0xa0000000,
-	.end	= 0xa1ffffff,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device mx31moboard_flash = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &mx31moboard_flash_data,
-	},
-	.resource = &mx31moboard_flash_resource,
-	.num_resources = 1,
-};
-
-static void __init moboard_uart0_init(void)
-{
-	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_CTS1), "uart0-cts-hack")) {
-		gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_CTS1), 0);
-		gpio_free(IOMUX_TO_GPIO(MX31_PIN_CTS1));
-	}
-}
-
-static const struct imxuart_platform_data uart0_pdata __initconst = {
-};
-
-static const struct imxuart_platform_data uart4_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data moboard_i2c0_data __initconst = {
-	.bitrate = 400000,
-};
-
-static const struct imxi2c_platform_data moboard_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct regulator_consumer_supply sdhc_consumers[] = {
-	{
-		.dev_name = "imx31-mmc.0",
-		.supply	= "sdhc0_vcc",
-	},
-	{
-		.dev_name = "imx31-mmc.1",
-		.supply	= "sdhc1_vcc",
-	},
-};
-
-static struct regulator_init_data sdhc_vreg_data = {
-	.constraints = {
-		.min_uV = 2700000,
-		.max_uV = 3000000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sdhc_consumers),
-	.consumer_supplies = sdhc_consumers,
-};
-
-static struct regulator_consumer_supply cam_consumers[] = {
-	{
-		.dev_name = "mx3_camera.0",
-		.supply = "cam_vcc",
-	},
-};
-
-static struct regulator_init_data cam_vreg_data = {
-	.constraints = {
-		.min_uV = 2700000,
-		.max_uV = 3000000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(cam_consumers),
-	.consumer_supplies = cam_consumers,
-};
-
-static struct mc13xxx_regulator_init_data moboard_regulators[] = {
-	{
-		.id = MC13783_REG_VMMC1,
-		.init_data = &sdhc_vreg_data,
-	},
-	{
-		.id = MC13783_REG_VCAM,
-		.init_data = &cam_vreg_data,
-	},
-};
-
-static struct mc13xxx_led_platform_data moboard_led[] = {
-	{
-		.id = MC13783_LED_R1,
-		.name = "coreboard-led-4:red",
-	},
-	{
-		.id = MC13783_LED_G1,
-		.name = "coreboard-led-4:green",
-	},
-	{
-		.id = MC13783_LED_B1,
-		.name = "coreboard-led-4:blue",
-	},
-	{
-		.id = MC13783_LED_R2,
-		.name = "coreboard-led-5:red",
-	},
-	{
-		.id = MC13783_LED_G2,
-		.name = "coreboard-led-5:green",
-	},
-	{
-		.id = MC13783_LED_B2,
-		.name = "coreboard-led-5:blue",
-	},
-};
-
-static struct mc13xxx_leds_platform_data moboard_leds = {
-	.num_leds = ARRAY_SIZE(moboard_led),
-	.led = moboard_led,
-	.led_control[0]	= MC13783_LED_C0_ENABLE | MC13783_LED_C0_ABMODE(0),
-	.led_control[1]	= MC13783_LED_C1_SLEWLIM,
-	.led_control[2]	= MC13783_LED_C2_SLEWLIM,
-	.led_control[3]	= MC13783_LED_C3_PERIOD(0) |
-			  MC13783_LED_C3_CURRENT_R1(2) |
-			  MC13783_LED_C3_CURRENT_G1(2) |
-			  MC13783_LED_C3_CURRENT_B1(2),
-	.led_control[4]	= MC13783_LED_C4_PERIOD(0) |
-			  MC13783_LED_C4_CURRENT_R2(3) |
-			  MC13783_LED_C4_CURRENT_G2(3) |
-			  MC13783_LED_C4_CURRENT_B2(3),
-};
-
-static struct mc13xxx_buttons_platform_data moboard_buttons = {
-	.b1on_flags = MC13783_BUTTON_DBNC_750MS | MC13783_BUTTON_ENABLE |
-			MC13783_BUTTON_POL_INVERT,
-	.b1on_key = KEY_POWER,
-};
-
-static struct mc13xxx_codec_platform_data moboard_codec = {
-	.dac_ssi_port = MC13783_SSI1_PORT,
-	.adc_ssi_port = MC13783_SSI1_PORT,
-};
-
-static struct mc13xxx_platform_data moboard_pmic = {
-	.regulators = {
-		.regulators = moboard_regulators,
-		.num_regulators = ARRAY_SIZE(moboard_regulators),
-	},
-	.leds = &moboard_leds,
-	.buttons = &moboard_buttons,
-	.codec = &moboard_codec,
-	.flags = MC13XXX_USE_RTC | MC13XXX_USE_ADC | MC13XXX_USE_CODEC,
-};
-
-static struct imx_ssi_platform_data moboard_ssi_pdata = {
-	.flags = IMX_SSI_DMA | IMX_SSI_NET,
-};
-
-static struct spi_board_info moboard_spi_board_info[] __initdata = {
-	{
-		.modalias = "mc13783",
-		/* irq number is run-time assigned */
-		.max_speed_hz = 300000,
-		.bus_num = 1,
-		.chip_select = 0,
-		.platform_data = &moboard_pmic,
-		.mode = SPI_CS_HIGH,
-	},
-};
-
-#define SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_ATA_CS0)
-#define SDHC1_WP IOMUX_TO_GPIO(MX31_PIN_ATA_CS1)
-
-static int moboard_sdhc1_get_ro(struct device *dev)
-{
-	return !gpio_get_value(SDHC1_WP);
-}
-
-static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-		void *data)
-{
-	int ret;
-
-	ret = gpio_request(SDHC1_CD, "sdhc-detect");
-	if (ret)
-		return ret;
-
-	gpio_direction_input(SDHC1_CD);
-
-	ret = gpio_request(SDHC1_WP, "sdhc-wp");
-	if (ret)
-		goto err_gpio_free;
-	gpio_direction_input(SDHC1_WP);
-
-	ret = request_irq(gpio_to_irq(SDHC1_CD), detect_irq,
-		IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-		"sdhc1-card-detect", data);
-	if (ret)
-		goto err_gpio_free_2;
-
-	return 0;
-
-err_gpio_free_2:
-	gpio_free(SDHC1_WP);
-err_gpio_free:
-	gpio_free(SDHC1_CD);
-
-	return ret;
-}
-
-static void moboard_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(SDHC1_CD), data);
-	gpio_free(SDHC1_WP);
-	gpio_free(SDHC1_CD);
-}
-
-static const struct imxmmc_platform_data sdhc1_pdata __initconst = {
-	.get_ro	= moboard_sdhc1_get_ro,
-	.init	= moboard_sdhc1_init,
-	.exit	= moboard_sdhc1_exit,
-};
-
-/*
- * this pin is dedicated for all mx31moboard systems, so we do it here
- */
-#define USB_RESET_B	IOMUX_TO_GPIO(MX31_PIN_GPIO1_0)
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-		      PAD_CTL_ODE_CMOS)
-
-#define OTG_EN_B IOMUX_TO_GPIO(MX31_PIN_USB_OC)
-#define USBH2_EN_B IOMUX_TO_GPIO(MX31_PIN_SCK6)
-
-static void usb_xcvr_reset(void)
-{
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG | PAD_CTL_100K_PU);
-
-	mxc_iomux_set_gpr(MUX_PGP_UH2, true);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG | PAD_CTL_100K_PD);
-	mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG | PAD_CTL_100K_PD);
-
-	gpio_request(OTG_EN_B, "usb-udc-en");
-	gpio_direction_output(OTG_EN_B, 0);
-	gpio_request(USBH2_EN_B, "usbh2-en");
-	gpio_direction_output(USBH2_EN_B, 0);
-
-	gpio_request(USB_RESET_B, "usb-reset");
-	gpio_direction_output(USB_RESET_B, 0);
-	mdelay(1);
-	gpio_set_value(USB_RESET_B, 1);
-	mdelay(1);
-}
-
-static int moboard_usbh2_init_hw(struct platform_device *pdev)
-{
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= moboard_usbh2_init_hw,
-	.portsc	= MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static int __init moboard_usbh2_init(void)
-{
-	struct platform_device *pdev;
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (!usbh2_pdata.otg)
-		return -ENODEV;
-
-	pdev = imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	return PTR_ERR_OR_ZERO(pdev);
-}
-
-static const struct gpio_led mx31moboard_leds[] __initconst = {
-	{
-		.name	= "coreboard-led-0:red:running",
-		.default_trigger = "heartbeat",
-		.gpio	= IOMUX_TO_GPIO(MX31_PIN_SVEN0),
-	}, {
-		.name	= "coreboard-led-1:red",
-		.gpio	= IOMUX_TO_GPIO(MX31_PIN_STX0),
-	}, {
-		.name	= "coreboard-led-2:red",
-		.gpio	= IOMUX_TO_GPIO(MX31_PIN_SRX0),
-	}, {
-		.name	= "coreboard-led-3:red",
-		.gpio	= IOMUX_TO_GPIO(MX31_PIN_SIMPD0),
-	},
-};
-
-static const struct gpio_led_platform_data mx31moboard_led_pdata __initconst = {
-	.num_leds	= ARRAY_SIZE(mx31moboard_leds),
-	.leds		= mx31moboard_leds,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&mx31moboard_flash,
-};
-
-static struct mx3_camera_pdata camera_pdata __initdata = {
-	.flags		= MX3_CAMERA_DATAWIDTH_8 | MX3_CAMERA_DATAWIDTH_10,
-	.mclk_10khz	= 4800,
-};
-
-static phys_addr_t mx3_camera_base __initdata;
-#define MX3_CAMERA_BUF_SIZE SZ_4M
-
-static int __init mx31moboard_init_cam(void)
-{
-	int ret;
-	struct platform_device *pdev;
-
-	imx31_add_ipu_core();
-
-	pdev = imx31_alloc_mx3_camera(&camera_pdata);
-	if (IS_ERR(pdev))
-		return PTR_ERR(pdev);
-
-	ret = dma_declare_coherent_memory(&pdev->dev,
-					  mx3_camera_base, mx3_camera_base,
-					  MX3_CAMERA_BUF_SIZE);
-	if (ret)
-		goto err;
-
-	ret = platform_device_add(pdev);
-	if (ret)
-err:
-		platform_device_put(pdev);
-
-	return ret;
-
-}
-
-static void mx31moboard_poweroff(void)
-{
-	struct clk *clk = clk_get_sys("imx2-wdt.0", NULL);
-
-	if (!IS_ERR(clk))
-		clk_prepare_enable(clk);
-
-	mxc_iomux_mode(MX31_PIN_WATCHDOG_RST__WATCHDOG_RST);
-
-	imx_writew(1 << 6 | 1 << 2, MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
-}
-
-static int mx31moboard_baseboard;
-core_param(mx31moboard_baseboard, mx31moboard_baseboard, int, 0444);
-
-/*
- * Board specific initialization.
- */
-static void __init mx31moboard_init(void)
-{
-	imx31_soc_init();
-
-	mxc_iomux_setup_multiple_pins(moboard_pins, ARRAY_SIZE(moboard_pins),
-		"moboard");
-
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	imx31_add_imx2_wdt();
-
-	imx31_add_imx_uart0(&uart0_pdata);
-	imx31_add_imx_uart4(&uart4_pdata);
-
-	imx31_add_imx_i2c0(&moboard_i2c0_data);
-	imx31_add_imx_i2c1(&moboard_i2c1_data);
-
-	imx31_add_spi_imx1(NULL);
-	imx31_add_spi_imx2(NULL);
-
-	mx31moboard_init_cam();
-
-	imx31_add_imx_ssi(0, &moboard_ssi_pdata);
-
-	pm_power_off = mx31moboard_poweroff;
-}
-
-static void __init mx31moboard_late(void)
-{
-	gpio_led_register_device(-1, &mx31moboard_led_pdata);
-
-	moboard_uart0_init();
-
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3), "pmic-irq");
-	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-	moboard_spi_board_info[0].irq =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-	spi_register_board_info(moboard_spi_board_info,
-		ARRAY_SIZE(moboard_spi_board_info));
-
-	imx31_add_mxc_mmc(0, &sdhc1_pdata);
-
-	usb_xcvr_reset();
-	moboard_usbh2_init();
-
-	imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
-
-	switch (mx31moboard_baseboard) {
-	case MX31NOBOARD:
-		break;
-	case MX31DEVBOARD:
-		mx31moboard_devboard_init();
-		break;
-	case MX31MARXBOT:
-		mx31moboard_marxbot_init();
-		break;
-	case MX31SMARTBOT:
-	case MX31EYEBOT:
-		mx31moboard_smartbot_init(mx31moboard_baseboard);
-		break;
-	default:
-		printk(KERN_ERR "Illegal mx31moboard_baseboard type %d\n",
-			mx31moboard_baseboard);
-	}
-}
-
-static void __init mx31moboard_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-static void __init mx31moboard_reserve(void)
-{
-	/* reserve 4 MiB for mx3-camera */
-	mx3_camera_base = arm_memblock_steal(MX3_CAMERA_BUF_SIZE,
-			MX3_CAMERA_BUF_SIZE);
-}
-
-MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
-	/* Maintainer: Philippe Retornaz, EPFL Mobots group */
-	.atag_offset = 0x100,
-	.reserve = mx31moboard_reserve,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= mx31moboard_timer_init,
-	.init_machine = mx31moboard_init,
-	.init_late	= mx31moboard_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
deleted file mode 100644
index 802e0abe4568..000000000000
--- a/arch/arm/mach-imx/mach-mx35_3ds.c
+++ /dev/null
@@ -1,516 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Marc Kleine-Budde, Pengutronix
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- *
- * Copyright (C) 2011 Meprolight, Ltd.
- * Alex Gershgorin <alexg@meprolight.com>
- *
- * Modified from i.MX31 3-Stack Development System
- */
-
-/*
- * This machine is known as:
- *  - i.MX35 3-Stack Development System
- *  - i.MX35 Platform Development Kit (i.MX35 PDK)
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/usb/otg.h>
-
-#include <linux/mtd/physmap.h>
-#include <linux/mfd/mc13892.h>
-#include <linux/regulator/machine.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include <video/platform_lcd.h>
-
-#include "3ds_debugboard.h"
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-#define GPIO_MC9S08DZ60_GPS_ENABLE 0
-#define GPIO_MC9S08DZ60_HDD_ENABLE 4
-#define GPIO_MC9S08DZ60_WIFI_ENABLE 5
-#define GPIO_MC9S08DZ60_LCD_ENABLE 6
-#define GPIO_MC9S08DZ60_SPEAKER_ENABLE 8
-
-static const struct fb_videomode fb_modedb[] = {
-	{
-		 /* 800x480 @ 55 Hz */
-		.name = "Ceramate-CLAA070VC01",
-		.refresh = 55,
-		.xres = 800,
-		.yres = 480,
-		.pixclock = 40000,
-		.left_margin = 40,
-		.right_margin = 40,
-		.upper_margin = 5,
-		.lower_margin = 5,
-		.hsync_len = 20,
-		.vsync_len = 10,
-		.sync = FB_SYNC_OE_ACT_HIGH,
-		.vmode = FB_VMODE_NONINTERLACED,
-		.flag = 0,
-	 },
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
-	.name = "Ceramate-CLAA070VC01",
-	.mode = fb_modedb,
-	.num_modes = ARRAY_SIZE(fb_modedb),
-};
-
-static struct i2c_board_info __initdata i2c_devices_3ds[] = {
-	{
-		I2C_BOARD_INFO("mc9s08dz60", 0x69),
-	},
-};
-
-static int lcd_power_gpio = -ENXIO;
-
-static int mc9s08dz60_gpiochip_match(struct gpio_chip *chip, void *data)
-{
-	return !strcmp(chip->label, data);
-}
-
-static void mx35_3ds_lcd_set_power(
-				struct plat_lcd_data *pd, unsigned int power)
-{
-	struct gpio_chip *chip;
-
-	if (!gpio_is_valid(lcd_power_gpio)) {
-		chip = gpiochip_find(
-				"mc9s08dz60", mc9s08dz60_gpiochip_match);
-		if (chip) {
-			lcd_power_gpio =
-				chip->base + GPIO_MC9S08DZ60_LCD_ENABLE;
-			if (gpio_request(lcd_power_gpio, "lcd_power") < 0) {
-				pr_err("error: gpio already requested!\n");
-				lcd_power_gpio = -ENXIO;
-			}
-		} else {
-			pr_err("error: didn't find mc9s08dz60 gpio chip\n");
-		}
-	}
-
-	if (gpio_is_valid(lcd_power_gpio))
-		gpio_set_value_cansleep(lcd_power_gpio, power);
-}
-
-static struct plat_lcd_data mx35_3ds_lcd_data = {
-	.set_power = mx35_3ds_lcd_set_power,
-};
-
-static struct platform_device mx35_3ds_lcd = {
-	.name = "platform-lcd",
-	.dev.platform_data = &mx35_3ds_lcd_data,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct physmap_flash_data mx35pdk_flash_data = {
-	.width  = 2,
-};
-
-static struct resource mx35pdk_flash_resource = {
-	.start	= MX35_CS0_BASE_ADDR,
-	.end	= MX35_CS0_BASE_ADDR + SZ_64M - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device mx35pdk_flash = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &mx35pdk_flash_data,
-	},
-	.resource = &mx35pdk_flash_resource,
-	.num_resources = 1,
-};
-
-static const struct mxc_nand_platform_data mx35pdk_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-	.flash_bbt = 1,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&mx35pdk_flash,
-};
-
-static const iomux_v3_cfg_t mx35pdk_pads[] __initconst = {
-	/* UART1 */
-	MX35_PAD_CTS1__UART1_CTS,
-	MX35_PAD_RTS1__UART1_RTS,
-	MX35_PAD_TXD1__UART1_TXD_MUX,
-	MX35_PAD_RXD1__UART1_RXD_MUX,
-	/* FEC */
-	MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
-	MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
-	MX35_PAD_FEC_RX_DV__FEC_RX_DV,
-	MX35_PAD_FEC_COL__FEC_COL,
-	MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
-	MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
-	MX35_PAD_FEC_TX_EN__FEC_TX_EN,
-	MX35_PAD_FEC_MDC__FEC_MDC,
-	MX35_PAD_FEC_MDIO__FEC_MDIO,
-	MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
-	MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
-	MX35_PAD_FEC_CRS__FEC_CRS,
-	MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
-	MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
-	MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
-	MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
-	MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
-	MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
-	/* USBOTG */
-	MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
-	MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
-	/* USBH1 */
-	MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR,
-	MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC,
-	/* SDCARD */
-	MX35_PAD_SD1_CMD__ESDHC1_CMD,
-	MX35_PAD_SD1_CLK__ESDHC1_CLK,
-	MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
-	MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
-	MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
-	MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
-	/* I2C1 */
-	MX35_PAD_I2C1_CLK__I2C1_SCL,
-	MX35_PAD_I2C1_DAT__I2C1_SDA,
-	/* Display */
-	MX35_PAD_LD0__IPU_DISPB_DAT_0,
-	MX35_PAD_LD1__IPU_DISPB_DAT_1,
-	MX35_PAD_LD2__IPU_DISPB_DAT_2,
-	MX35_PAD_LD3__IPU_DISPB_DAT_3,
-	MX35_PAD_LD4__IPU_DISPB_DAT_4,
-	MX35_PAD_LD5__IPU_DISPB_DAT_5,
-	MX35_PAD_LD6__IPU_DISPB_DAT_6,
-	MX35_PAD_LD7__IPU_DISPB_DAT_7,
-	MX35_PAD_LD8__IPU_DISPB_DAT_8,
-	MX35_PAD_LD9__IPU_DISPB_DAT_9,
-	MX35_PAD_LD10__IPU_DISPB_DAT_10,
-	MX35_PAD_LD11__IPU_DISPB_DAT_11,
-	MX35_PAD_LD12__IPU_DISPB_DAT_12,
-	MX35_PAD_LD13__IPU_DISPB_DAT_13,
-	MX35_PAD_LD14__IPU_DISPB_DAT_14,
-	MX35_PAD_LD15__IPU_DISPB_DAT_15,
-	MX35_PAD_LD16__IPU_DISPB_DAT_16,
-	MX35_PAD_LD17__IPU_DISPB_DAT_17,
-	MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
-	MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
-	MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
-	MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
-	MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
-	MX35_PAD_D3_REV__IPU_DISPB_D3_REV,
-	MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS,
-	/*PMIC IRQ*/
-	MX35_PAD_GPIO2_0__GPIO2_0,
-};
-
-static struct regulator_consumer_supply sw1_consumers[] = {
-	{
-		.supply = "cpu_vcc",
-	}
-};
-
-static struct regulator_consumer_supply vcam_consumers[] = {
-	/* sgtl5000 */
-	REGULATOR_SUPPLY("VDDA", "0-000a"),
-};
-
-static struct regulator_init_data sw1_init = {
-	.constraints = {
-		.name = "SW1",
-		.min_uV = 600000,
-		.max_uV = 1375000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.valid_modes_mask = 0,
-		.always_on = 1,
-		.boot_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sw1_consumers),
-	.consumer_supplies = sw1_consumers,
-};
-
-static struct regulator_init_data sw2_init = {
-	.constraints = {
-		.name = "SW2",
-		.always_on = 1,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data sw3_init = {
-	.constraints = {
-		.name = "SW3",
-		.always_on = 1,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data sw4_init = {
-	.constraints = {
-		.name = "SW4",
-		.always_on = 1,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data viohi_init = {
-	.constraints = {
-		.name = "VIOHI",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vusb_init = {
-	.constraints = {
-		.name = "VUSB",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vdig_init = {
-	.constraints = {
-		.name = "VDIG",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vpll_init = {
-	.constraints = {
-		.name = "VPLL",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vusb2_init = {
-	.constraints = {
-		.name = "VUSB2",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vvideo_init = {
-	.constraints = {
-		.name = "VVIDEO",
-		.boot_on = 1
-	}
-};
-
-static struct regulator_init_data vcam_init = {
-	.constraints = {
-		.name = "VCAM",
-		.min_uV = 2500000,
-		.max_uV = 3000000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-					REGULATOR_CHANGE_MODE,
-		.valid_modes_mask = REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL,
-		.boot_on = 1
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vcam_consumers),
-	.consumer_supplies = vcam_consumers,
-};
-
-static struct regulator_init_data vgen1_init = {
-	.constraints = {
-		.name = "VGEN1",
-	}
-};
-
-static struct regulator_init_data vgen2_init = {
-	.constraints = {
-		.name = "VGEN2",
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vgen3_init = {
-	.constraints = {
-		.name = "VGEN3",
-	}
-};
-
-static struct mc13xxx_regulator_init_data mx35_3ds_regulators[] = {
-	{ .id = MC13892_SW1, .init_data = &sw1_init },
-	{ .id = MC13892_SW2, .init_data = &sw2_init },
-	{ .id = MC13892_SW3, .init_data = &sw3_init },
-	{ .id = MC13892_SW4, .init_data = &sw4_init },
-	{ .id = MC13892_VIOHI, .init_data = &viohi_init },
-	{ .id = MC13892_VPLL, .init_data = &vpll_init },
-	{ .id = MC13892_VDIG, .init_data = &vdig_init },
-	{ .id = MC13892_VUSB2, .init_data = &vusb2_init },
-	{ .id = MC13892_VVIDEO, .init_data = &vvideo_init },
-	{ .id = MC13892_VCAM, .init_data = &vcam_init },
-	{ .id = MC13892_VGEN1, .init_data = &vgen1_init },
-	{ .id = MC13892_VGEN2, .init_data = &vgen2_init },
-	{ .id = MC13892_VGEN3, .init_data = &vgen3_init },
-	{ .id = MC13892_VUSB, .init_data = &vusb_init },
-};
-
-static struct mc13xxx_platform_data mx35_3ds_mc13892_data = {
-	.flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
-	.regulators = {
-		.num_regulators = ARRAY_SIZE(mx35_3ds_regulators),
-		.regulators = mx35_3ds_regulators,
-	},
-};
-
-#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
-
-static struct i2c_board_info mx35_3ds_i2c_mc13892 = {
-
-	I2C_BOARD_INFO("mc13892", 0x08),
-	.platform_data = &mx35_3ds_mc13892_data,
-	/* irq number is run-time assigned */
-};
-
-static void __init imx35_3ds_init_mc13892(void)
-{
-	int ret = gpio_request_one(GPIO_PMIC_INT, GPIOF_DIR_IN, "pmic irq");
-
-	if (ret) {
-		pr_err("failed to get pmic irq: %d\n", ret);
-		return;
-	}
-
-	mx35_3ds_i2c_mc13892.irq = gpio_to_irq(GPIO_PMIC_INT);
-	i2c_register_board_info(0, &mx35_3ds_i2c_mc13892, 1);
-}
-
-static int mx35_3ds_otg_init(struct platform_device *pdev)
-{
-	return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
-}
-
-/* OTG config */
-static const struct fsl_usb2_platform_data usb_otg_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_UTMI_WIDE,
-	.workaround	= FLS_USB2_WORKAROUND_ENGCM09152,
-/*
- * ENGCM09152 also requires a hardware change.
- * Please check the MX35 Chip Errata document for details.
- */
-};
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= mx35_3ds_otg_init,
-	.portsc	= MXC_EHCI_MODE_UTMI,
-};
-
-static int mx35_3ds_usbh_init(struct platform_device *pdev)
-{
-	return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
-			  MXC_EHCI_INTERNAL_PHY);
-}
-
-/* USB HOST config */
-static const struct mxc_usbh_platform_data usb_host_pdata __initconst = {
-	.init		= mx35_3ds_usbh_init,
-	.portsc		= MXC_EHCI_MODE_SERIAL,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init mx35_3ds_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", mx35_3ds_otg_mode);
-
-static const struct imxi2c_platform_data mx35_3ds_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init mx35_3ds_init(void)
-{
-	imx35_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(mx35pdk_pads, ARRAY_SIZE(mx35pdk_pads));
-
-	imx35_add_fec(NULL);
-	imx35_add_imx2_wdt();
-	imx35_add_mxc_rtc();
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	imx35_add_imx_uart0(&uart_pdata);
-
-	if (otg_mode_host)
-		imx35_add_mxc_ehci_otg(&otg_pdata);
-
-	imx35_add_mxc_ehci_hs(&usb_host_pdata);
-
-	if (!otg_mode_host)
-		imx35_add_fsl_usb2_udc(&usb_otg_pdata);
-
-	imx35_add_mxc_nand(&mx35pdk_nand_board_info);
-	imx35_add_sdhci_esdhc_imx(0, NULL);
-
-	imx35_add_imx_i2c0(&mx35_3ds_i2c0_data);
-
-	i2c_register_board_info(
-		0, i2c_devices_3ds, ARRAY_SIZE(i2c_devices_3ds));
-
-	imx35_add_ipu_core();
-}
-
-static void __init mx35_3ds_late_init(void)
-{
-	struct platform_device *imx35_fb_pdev;
-
-	if (mxc_expio_init(MX35_CS5_BASE_ADDR, IMX_GPIO_NR(1, 1)))
-		pr_warn("Init of the debugboard failed, all "
-			"devices on the debugboard are unusable.\n");
-
-	imx35_fb_pdev = imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-	mx35_3ds_lcd.dev.parent = &imx35_fb_pdev->dev;
-	platform_device_register(&mx35_3ds_lcd);
-
-	imx35_3ds_init_mc13892();
-}
-
-static void __init mx35pdk_timer_init(void)
-{
-	mx35_clocks_init();
-}
-
-MACHINE_START(MX35_3DS, "Freescale MX35PDK")
-	/* Maintainer: Freescale Semiconductor, Inc */
-	.atag_offset = 0x100,
-	.map_io = mx35_map_io,
-	.init_early = imx35_init_early,
-	.init_irq = mx35_init_irq,
-	.init_time	= mx35pdk_timer_init,
-	.init_machine = mx35_3ds_init,
-	.init_late	= mx35_3ds_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c
deleted file mode 100644
index 27a3678e0658..000000000000
--- a/arch/arm/mach-imx/mach-pca100.c
+++ /dev/null
@@ -1,426 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2007 Robert Schwebel <r.schwebel@pengutronix.de>, Pengutronix
- * Copyright (C) 2009 Sascha Hauer (kernel@pengutronix.de)
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/dma-mapping.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/eeprom.h>
-#include <linux/irq.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <asm/mach/time.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-#define OTG_PHY_CS_GPIO (GPIO_PORTB + 23)
-#define USBH2_PHY_CS_GPIO (GPIO_PORTB + 24)
-#define SPI1_SS0 (GPIO_PORTD + 28)
-#define SPI1_SS1 (GPIO_PORTD + 27)
-#define SD2_CD (GPIO_PORTC + 29)
-
-static const int pca100_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* SDHC */
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-	SD2_CD | GPIO_GPIO | GPIO_IN,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* SSI1 */
-	PC20_PF_SSI1_FS,
-	PC21_PF_SSI1_RXD,
-	PC22_PF_SSI1_TXD,
-	PC23_PF_SSI1_CLK,
-	/* onboard I2C */
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* external I2C */
-	PD17_PF_I2C_DATA,
-	PD18_PF_I2C_CLK,
-	/* SPI1 */
-	PD25_PF_CSPI1_RDY,
-	PD29_PF_CSPI1_SCLK,
-	PD30_PF_CSPI1_MISO,
-	PD31_PF_CSPI1_MOSI,
-	/* OTG */
-	OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
-	PC7_PF_USBOTG_DATA5,
-	PC8_PF_USBOTG_DATA6,
-	PC9_PF_USBOTG_DATA0,
-	PC10_PF_USBOTG_DATA2,
-	PC11_PF_USBOTG_DATA1,
-	PC12_PF_USBOTG_DATA4,
-	PC13_PF_USBOTG_DATA3,
-	PE0_PF_USBOTG_NXT,
-	PE1_PF_USBOTG_STP,
-	PE2_PF_USBOTG_DIR,
-	PE24_PF_USBOTG_CLK,
-	PE25_PF_USBOTG_DATA7,
-	/* USBH2 */
-	USBH2_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT,
-	PA0_PF_USBH2_CLK,
-	PA1_PF_USBH2_DIR,
-	PA2_PF_USBH2_DATA7,
-	PA3_PF_USBH2_NXT,
-	PA4_PF_USBH2_STP,
-	PD19_AF_USBH2_DATA4,
-	PD20_AF_USBH2_DATA3,
-	PD21_AF_USBH2_DATA6,
-	PD22_AF_USBH2_DATA0,
-	PD23_AF_USBH2_DATA2,
-	PD24_AF_USBH2_DATA1,
-	PD26_AF_USBH2_DATA5,
-	/* display */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA26_PF_PS,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA31_PF_OE_ACD,
-	/* free GPIO */
-	GPIO_PORTC | 31 | GPIO_GPIO | GPIO_IN, /* GPIO0_IRQ */
-	GPIO_PORTC | 25 | GPIO_GPIO | GPIO_IN, /* GPIO1_IRQ */
-	GPIO_PORTE | 5 | GPIO_GPIO | GPIO_IN, /* GPIO2_IRQ */
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-pca100_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static const struct imxi2c_platform_data pca100_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 32),
-	{ }
-};
-
-static struct i2c_board_info pca100_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
-		.properties = board_eeprom_properties,
-	}, {
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	}, {
-		I2C_BOARD_INFO("lm75", 0x4a),
-	}
-};
-
-static struct spi_eeprom at25320 = {
-	.name		= "at25320an",
-	.byte_len	= 4096,
-	.page_size	= 32,
-	.flags		= EE_ADDR2,
-};
-
-static struct spi_board_info pca100_spi_board_info[] __initdata = {
-	{
-		.modalias = "at25",
-		.max_speed_hz = 30000,
-		.bus_num = 0,
-		.chip_select = 1,
-		.platform_data = &at25320,
-	},
-};
-
-static struct gpiod_lookup_table pca100_spi0_gpiod_table = {
-	.dev_id = "imx27-cspi.0", /* Actual device name for spi0 */
-	.table = {
-		/*
-		 * The i.MX27 has the i.MX21 GPIO controller, port D is
-		 * bank 3 and thus named "imx21-gpio.3".
-		 * SPI1_SS0 is GPIO_PORTD + 28
-		 * SPI1_SS1 is GPIO_PORTD + 27
-		 */
-		GPIO_LOOKUP_IDX("imx21-gpio.3", 28, "cs", 0, GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP_IDX("imx21-gpio.3", 27, "cs", 1, GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static void pca100_ac97_warm_reset(struct snd_ac97 *ac97)
-{
-	mxc_gpio_mode(GPIO_PORTC | 20 | GPIO_GPIO | GPIO_OUT);
-	gpio_set_value(GPIO_PORTC + 20, 1);
-	udelay(2);
-	gpio_set_value(GPIO_PORTC + 20, 0);
-	mxc_gpio_mode(PC20_PF_SSI1_FS);
-	msleep(2);
-}
-
-static void pca100_ac97_cold_reset(struct snd_ac97 *ac97)
-{
-	mxc_gpio_mode(GPIO_PORTC | 20 | GPIO_GPIO | GPIO_OUT);  /* FS */
-	gpio_set_value(GPIO_PORTC + 20, 0);
-	mxc_gpio_mode(GPIO_PORTC | 22 | GPIO_GPIO | GPIO_OUT);  /* TX */
-	gpio_set_value(GPIO_PORTC + 22, 0);
-	mxc_gpio_mode(GPIO_PORTC | 28 | GPIO_GPIO | GPIO_OUT);  /* reset */
-	gpio_set_value(GPIO_PORTC + 28, 0);
-	udelay(10);
-	gpio_set_value(GPIO_PORTC + 28, 1);
-	mxc_gpio_mode(PC20_PF_SSI1_FS);
-	mxc_gpio_mode(PC22_PF_SSI1_TXD);
-	msleep(2);
-}
-
-static const struct imx_ssi_platform_data pca100_ssi_pdata __initconst = {
-	.ac97_reset		= pca100_ac97_cold_reset,
-	.ac97_warm_reset	= pca100_ac97_warm_reset,
-	.flags			= IMX_SSI_USE_AC97,
-};
-
-static int pca100_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
-		void *data)
-{
-	int ret;
-
-	ret = request_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), detect_irq,
-			  IRQF_TRIGGER_FALLING, "imx-mmc-detect", data);
-	if (ret)
-		printk(KERN_ERR
-			"pca100: Failed to request irq for sd/mmc detection\n");
-
-	return ret;
-}
-
-static void pca100_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.init = pca100_sdhc2_init,
-	.exit = pca100_sdhc2_exit,
-};
-
-static int otg_phy_init(struct platform_device *pdev)
-{
-	gpio_set_value(OTG_PHY_CS_GPIO, 0);
-
-	mdelay(10);
-
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= otg_phy_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static int usbh2_phy_init(struct platform_device *pdev)
-{
-	gpio_set_value(USBH2_PHY_CS_GPIO, 0);
-
-	mdelay(10);
-
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= usbh2_phy_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pca100_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", pca100_otg_mode);
-
-/* framebuffer info */
-static struct imx_fb_videomode pca100_fb_modes[] = {
-	{
-		.mode = {
-			.name		= "EMERGING-ETV570G0DHU",
-			.refresh	= 60,
-			.xres		= 640,
-			.yres		= 480,
-			.pixclock	= 39722, /* in ps (25.175 MHz) */
-			.hsync_len	= 30,
-			.left_margin	= 114,
-			.right_margin	= 16,
-			.vsync_len	= 3,
-			.upper_margin	= 32,
-			.lower_margin	= 0,
-		},
-		/*
-		 * TFT
-		 * Pixel pol active high
-		 * HSYNC active low
-		 * VSYNC active low
-		 * use HSYNC for ACD count
-		 * line clock disable while idle
-		 * always enable line clock even if no data
-		 */
-		.pcr = 0xf0c08080,
-		.bpp = 16,
-	},
-};
-
-static const struct imx_fb_platform_data pca100_fb_data __initconst = {
-	.mode = pca100_fb_modes,
-	.num_modes = ARRAY_SIZE(pca100_fb_modes),
-
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static void __init pca100_init(void)
-{
-	int ret;
-
-	imx27_soc_init();
-
-	ret = mxc_gpio_setup_multiple_pins(pca100_pins,
-			ARRAY_SIZE(pca100_pins), "PCA100");
-	if (ret)
-		printk(KERN_ERR "pca100: Failed to setup pins (%d)\n", ret);
-
-	imx27_add_imx_uart0(&uart_pdata);
-
-	imx27_add_mxc_nand(&pca100_nand_board_info);
-
-	/* only the i2c master 1 is used on this CPU card */
-	i2c_register_board_info(1, pca100_i2c_devices,
-				ARRAY_SIZE(pca100_i2c_devices));
-
-	imx27_add_imx_i2c(1, &pca100_i2c1_data);
-
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_IN);
-	mxc_gpio_mode(GPIO_PORTD | 27 | GPIO_GPIO | GPIO_IN);
-	spi_register_board_info(pca100_spi_board_info,
-				ARRAY_SIZE(pca100_spi_board_info));
-	imx27_add_spi_imx0(&pca100_spi0_gpiod_table);
-
-	imx27_add_imx_fb(&pca100_fb_data);
-
-	imx27_add_fec(NULL);
-	imx27_add_imx2_wdt();
-	imx27_add_mxc_w1();
-}
-
-static void __init pca100_late_init(void)
-{
-	imx27_add_imx_ssi(0, &pca100_ssi_pdata);
-
-	imx27_add_mxc_mmc(1, &sdhc_pdata);
-
-	gpio_request(OTG_PHY_CS_GPIO, "usb-otg-cs");
-	gpio_direction_output(OTG_PHY_CS_GPIO, 1);
-	gpio_request(USBH2_PHY_CS_GPIO, "usb-host2-cs");
-	gpio_direction_output(USBH2_PHY_CS_GPIO, 1);
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-
-		if (otg_pdata.otg)
-			imx27_add_mxc_ehci_otg(&otg_pdata);
-	} else {
-		gpio_set_value(OTG_PHY_CS_GPIO, 0);
-		imx27_add_fsl_usb2_udc(&otg_device_pdata);
-	}
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(
-			ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT);
-
-	if (usbh2_pdata.otg)
-		imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-}
-
-static void __init pca100_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(PCA100, "phyCARD-i.MX27")
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_machine	= pca100_init,
-	.init_late	= pca100_late_init,
-	.init_time	= pca100_timer_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pcm037.c b/arch/arm/mach-imx/mach-pcm037.c
deleted file mode 100644
index c7d23e9d4f8b..000000000000
--- a/arch/arm/mach-imx/mach-pcm037.c
+++ /dev/null
@@ -1,585 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2008 Sascha Hauer, Pengutronix
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/delay.h>
-#include <linux/spi/spi.h>
-#include <linux/irq.h>
-#include <linux/can/platform/sja1000.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <linux/gfp.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "pcm037.h"
-#include "ulpi.h"
-
-static enum pcm037_board_variant pcm037_instance = PCM037_PCM970;
-
-static int __init pcm037_variant_setup(char *str)
-{
-	if (!strcmp("eet", str))
-		pcm037_instance = PCM037_EET;
-	else if (strcmp("pcm970", str))
-		pr_warn("Unknown pcm037 baseboard variant %s\n", str);
-
-	return 1;
-}
-
-/* Supported values: "pcm970" (default) and "eet" */
-__setup("pcm037_variant=", pcm037_variant_setup);
-
-enum pcm037_board_variant pcm037_variant(void)
-{
-	return pcm037_instance;
-}
-
-/* UART1 with RTS/CTS handshake signals */
-static unsigned int pcm037_uart1_handshake_pins[] = {
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-};
-
-/* UART1 without RTS/CTS handshake signals */
-static unsigned int pcm037_uart1_pins[] = {
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1,
-};
-
-static unsigned int pcm037_pins[] = {
-	/* I2C */
-	MX31_PIN_CSPI2_MOSI__SCL,
-	MX31_PIN_CSPI2_MISO__SDA,
-	MX31_PIN_CSPI2_SS2__I2C3_SDA,
-	MX31_PIN_CSPI2_SCLK__I2C3_SCL,
-	/* SDHC1 */
-	MX31_PIN_SD1_DATA3__SD1_DATA3,
-	MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA1__SD1_DATA1,
-	MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_CLK__SD1_CLK,
-	MX31_PIN_SD1_CMD__SD1_CMD,
-	IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */
-	IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */
-	/* SPI1 */
-	MX31_PIN_CSPI1_MOSI__MOSI,
-	MX31_PIN_CSPI1_MISO__MISO,
-	MX31_PIN_CSPI1_SCLK__SCLK,
-	MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI1_SS0__SS0,
-	MX31_PIN_CSPI1_SS1__SS1,
-	MX31_PIN_CSPI1_SS2__SS2,
-	/* UART2 */
-	MX31_PIN_TXD2__TXD2,
-	MX31_PIN_RXD2__RXD2,
-	MX31_PIN_CTS2__CTS2,
-	MX31_PIN_RTS2__RTS2,
-	/* UART3 */
-	MX31_PIN_CSPI3_MOSI__RXD3,
-	MX31_PIN_CSPI3_MISO__TXD3,
-	MX31_PIN_CSPI3_SCLK__RTS3,
-	MX31_PIN_CSPI3_SPI_RDY__CTS3,
-	/* LAN9217 irq pin */
-	IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO),
-	/* Onewire */
-	MX31_PIN_BATT_LINE__OWIRE,
-	/* Framebuffer */
-	MX31_PIN_LD0__LD0,
-	MX31_PIN_LD1__LD1,
-	MX31_PIN_LD2__LD2,
-	MX31_PIN_LD3__LD3,
-	MX31_PIN_LD4__LD4,
-	MX31_PIN_LD5__LD5,
-	MX31_PIN_LD6__LD6,
-	MX31_PIN_LD7__LD7,
-	MX31_PIN_LD8__LD8,
-	MX31_PIN_LD9__LD9,
-	MX31_PIN_LD10__LD10,
-	MX31_PIN_LD11__LD11,
-	MX31_PIN_LD12__LD12,
-	MX31_PIN_LD13__LD13,
-	MX31_PIN_LD14__LD14,
-	MX31_PIN_LD15__LD15,
-	MX31_PIN_LD16__LD16,
-	MX31_PIN_LD17__LD17,
-	MX31_PIN_VSYNC3__VSYNC3,
-	MX31_PIN_HSYNC__HSYNC,
-	MX31_PIN_FPSHIFT__FPSHIFT,
-	MX31_PIN_DRDY0__DRDY0,
-	MX31_PIN_D3_REV__D3_REV,
-	MX31_PIN_CONTRAST__CONTRAST,
-	MX31_PIN_D3_SPL__D3_SPL,
-	MX31_PIN_D3_CLS__D3_CLS,
-	MX31_PIN_LCS0__GPIO3_23,
-	/* GPIO */
-	IOMUX_MODE(MX31_PIN_ATA_DMACK, IOMUX_CONFIG_GPIO),
-	/* OTG */
-	MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
-	MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
-	MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
-	MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
-	MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
-	MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
-	MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
-	MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
-	MX31_PIN_USBOTG_CLK__USBOTG_CLK,
-	MX31_PIN_USBOTG_DIR__USBOTG_DIR,
-	MX31_PIN_USBOTG_NXT__USBOTG_NXT,
-	MX31_PIN_USBOTG_STP__USBOTG_STP,
-	/* USB host 2 */
-	IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
-	IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
-};
-
-static struct physmap_flash_data pcm037_flash_data = {
-	.width  = 2,
-};
-
-static struct resource pcm037_flash_resource = {
-	.start	= 0xa0000000,
-	.end	= 0xa1ffffff,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device pcm037_flash = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &pcm037_flash_data,
-	},
-	.resource = &pcm037_flash_resource,
-	.num_resources = 1,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct resource smsc911x_resources[] = {
-	{
-		.start		= MX31_CS1_BASE_ADDR + 0x300,
-		.end		= MX31_CS1_BASE_ADDR + 0x300 + SZ_64K - 1,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags		= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
-	},
-};
-
-static struct smsc911x_platform_config smsc911x_info = {
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY |
-			  SMSC911X_SAVE_MAC_ADDRESS,
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-};
-
-static struct platform_device pcm037_eth = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(smsc911x_resources),
-	.resource	= smsc911x_resources,
-	.dev		= {
-		.platform_data = &smsc911x_info,
-	},
-};
-
-static struct platdata_mtd_ram pcm038_sram_data = {
-	.bankwidth = 2,
-};
-
-static struct resource pcm038_sram_resource = {
-	.start = MX31_CS4_BASE_ADDR,
-	.end   = MX31_CS4_BASE_ADDR + 512 * 1024 - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm037_sram_device = {
-	.name = "mtd-ram",
-	.id = 0,
-	.dev = {
-		.platform_data = &pcm038_sram_data,
-	},
-	.num_resources = 1,
-	.resource = &pcm038_sram_resource,
-};
-
-static const struct mxc_nand_platform_data
-pcm037_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static const struct imxi2c_platform_data pcm037_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static const struct imxi2c_platform_data pcm037_i2c2_data __initconst = {
-	.bitrate = 20000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 32),
-	{ }
-};
-
-static struct i2c_board_info pcm037_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
-		.properties = board_eeprom_properties,
-	}, {
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	}
-};
-
-/* Not connected by default */
-#ifdef PCM970_SDHC_RW_SWITCH
-static int pcm970_sdhc1_get_ro(struct device *dev)
-{
-	return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_SFS6));
-}
-#endif
-
-#define SDHC1_GPIO_WP	IOMUX_TO_GPIO(MX31_PIN_SFS6)
-#define SDHC1_GPIO_DET	IOMUX_TO_GPIO(MX31_PIN_SCK6)
-
-static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-		void *data)
-{
-	int ret;
-
-	ret = gpio_request(SDHC1_GPIO_DET, "sdhc-detect");
-	if (ret)
-		return ret;
-
-	gpio_direction_input(SDHC1_GPIO_DET);
-
-#ifdef PCM970_SDHC_RW_SWITCH
-	ret = gpio_request(SDHC1_GPIO_WP, "sdhc-wp");
-	if (ret)
-		goto err_gpio_free;
-	gpio_direction_input(SDHC1_GPIO_WP);
-#endif
-
-	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), detect_irq,
-			IRQF_TRIGGER_FALLING, "sdhc-detect", data);
-	if (ret)
-		goto err_gpio_free_2;
-
-	return 0;
-
-err_gpio_free_2:
-#ifdef PCM970_SDHC_RW_SWITCH
-	gpio_free(SDHC1_GPIO_WP);
-err_gpio_free:
-#endif
-	gpio_free(SDHC1_GPIO_DET);
-
-	return ret;
-}
-
-static void pcm970_sdhc1_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), data);
-	gpio_free(SDHC1_GPIO_DET);
-	gpio_free(SDHC1_GPIO_WP);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-#ifdef PCM970_SDHC_RW_SWITCH
-	.get_ro = pcm970_sdhc1_get_ro,
-#endif
-	.init = pcm970_sdhc1_init,
-	.exit = pcm970_sdhc1_exit,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&pcm037_flash,
-	&pcm037_sram_device,
-};
-
-static const struct fb_videomode fb_modedb[] = {
-	{
-		/* 240x320 @ 60 Hz Sharp */
-		.name		= "Sharp-LQ035Q7DH06-QVGA",
-		.refresh	= 60,
-		.xres		= 240,
-		.yres		= 320,
-		.pixclock	= 185925,
-		.left_margin	= 9,
-		.right_margin	= 16,
-		.upper_margin	= 7,
-		.lower_margin	= 9,
-		.hsync_len	= 1,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE |
-				  FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}, {
-		/* 240x320 @ 60 Hz */
-		.name		= "TX090",
-		.refresh	= 60,
-		.xres		= 240,
-		.yres		= 320,
-		.pixclock	= 38255,
-		.left_margin	= 144,
-		.right_margin	= 0,
-		.upper_margin	= 7,
-		.lower_margin	= 40,
-		.hsync_len	= 96,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}, {
-		/* 240x320 @ 60 Hz */
-		.name		= "CMEL-OLED",
-		.refresh	= 60,
-		.xres		= 240,
-		.yres		= 320,
-		.pixclock	= 185925,
-		.left_margin	= 9,
-		.right_margin	= 16,
-		.upper_margin	= 7,
-		.lower_margin	= 9,
-		.hsync_len	= 1,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	},
-};
-
-static struct mx3fb_platform_data mx3fb_pdata = {
-	.name		= "Sharp-LQ035Q7DH06-QVGA",
-	.mode		= fb_modedb,
-	.num_modes	= ARRAY_SIZE(fb_modedb),
-};
-
-static struct resource pcm970_sja1000_resources[] = {
-	{
-		.start   = MX31_CS5_BASE_ADDR,
-		.end     = MX31_CS5_BASE_ADDR + 0x100 - 1,
-		.flags   = IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags   = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
-	},
-};
-
-static struct sja1000_platform_data pcm970_sja1000_platform_data = {
-	.osc_freq	= 16000000,
-	.ocr		= OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL,
-	.cdr		= CDR_CBP,
-};
-
-static struct platform_device pcm970_sja1000 = {
-	.name = "sja1000_platform",
-	.dev = {
-		.platform_data = &pcm970_sja1000_platform_data,
-	},
-	.resource = pcm970_sja1000_resources,
-	.num_resources = ARRAY_SIZE(pcm970_sja1000_resources),
-};
-
-static int pcm037_otg_init(struct platform_device *pdev)
-{
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= pcm037_otg_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static int pcm037_usbh2_init(struct platform_device *pdev)
-{
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
-	.init	= pcm037_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_ULPI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pcm037_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", pcm037_otg_mode);
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-/*
- * Board specific initialization.
- */
-static void __init pcm037_init(void)
-{
-	imx31_soc_init();
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
-	mxc_iomux_set_gpr(MUX_PGP_UH2, 1);
-
-	mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins),
-			"pcm037");
-
-#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS \
-		| PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
-	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
-	mxc_iomux_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG);	/* USBH2_DATA2 */
-	mxc_iomux_set_pad(MX31_PIN_STXD6, H2_PAD_CFG);	/* USBH2_DATA3 */
-	mxc_iomux_set_pad(MX31_PIN_SFS3, H2_PAD_CFG);	/* USBH2_DATA4 */
-	mxc_iomux_set_pad(MX31_PIN_SCK3, H2_PAD_CFG);	/* USBH2_DATA5 */
-	mxc_iomux_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	/* USBH2_DATA6 */
-	mxc_iomux_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	/* USBH2_DATA7 */
-
-	if (pcm037_variant() == PCM037_EET)
-		mxc_iomux_setup_multiple_pins(pcm037_uart1_pins,
-			ARRAY_SIZE(pcm037_uart1_pins), "pcm037_uart1");
-	else
-		mxc_iomux_setup_multiple_pins(pcm037_uart1_handshake_pins,
-			ARRAY_SIZE(pcm037_uart1_handshake_pins),
-			"pcm037_uart1");
-
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	imx31_add_imx2_wdt();
-	imx31_add_imx_uart0(&uart_pdata);
-	/* XXX: should't this have .flags = 0 (i.e. no RTSCTS) on PCM037_EET? */
-	imx31_add_imx_uart1(&uart_pdata);
-	imx31_add_imx_uart2(&uart_pdata);
-
-	imx31_add_mxc_w1();
-
-	/* I2C adapters and devices */
-	i2c_register_board_info(1, pcm037_i2c_devices,
-			ARRAY_SIZE(pcm037_i2c_devices));
-
-	imx31_add_imx_i2c1(&pcm037_i2c1_data);
-	imx31_add_imx_i2c2(&pcm037_i2c2_data);
-
-	imx31_add_mxc_nand(&pcm037_nand_board_info);
-	imx31_add_ipu_core();
-	imx31_add_mx3_sdc_fb(&mx3fb_pdata);
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-		if (otg_pdata.otg)
-			imx31_add_mxc_ehci_otg(&otg_pdata);
-	}
-
-	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT);
-	if (usbh2_pdata.otg)
-		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	if (!otg_mode_host)
-		imx31_add_fsl_usb2_udc(&otg_device_pdata);
-}
-
-static void __init pcm037_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-static void __init pcm037_init_late(void)
-{
-	int ret;
-
-	/* LAN9217 IRQ pin */
-	ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq");
-	if (!ret) {
-		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
-		smsc911x_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
-		smsc911x_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
-		platform_device_register(&pcm037_eth);
-	} else {
-		pr_warn("could not get LAN irq gpio\n");
-	}
-
-	imx31_add_mxc_mmc(0, &sdhc_pdata);
-
-	pcm970_sja1000_resources[1].start =
-			gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105)));
-	pcm970_sja1000_resources[1].end =
-			gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105)));
-	platform_device_register(&pcm970_sja1000);
-
-	pcm037_eet_init_devices();
-}
-
-MACHINE_START(PCM037, "Phytec Phycore pcm037")
-	/* Maintainer: Pengutronix */
-	.atag_offset = 0x100,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= pcm037_timer_init,
-	.init_machine = pcm037_init,
-	.init_late = pcm037_init_late,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-pcm037_eet.c b/arch/arm/mach-imx/mach-pcm037_eet.c
deleted file mode 100644
index 8b0e03a595c1..000000000000
--- a/arch/arm/mach-imx/mach-pcm037_eet.c
+++ /dev/null
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2009
- * Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
- */
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-
-#include <asm/mach-types.h>
-
-#include "pcm037.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "iomux-mx3.h"
-
-static unsigned int pcm037_eet_pins[] = {
-	/* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */
-	IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
-	/* GPIO keys */
-	IOMUX_MODE(MX31_PIN_GPIO1_0,	IOMUX_CONFIG_GPIO), /* 0 */
-	IOMUX_MODE(MX31_PIN_GPIO1_1,	IOMUX_CONFIG_GPIO), /* 1 */
-	IOMUX_MODE(MX31_PIN_GPIO1_2,	IOMUX_CONFIG_GPIO), /* 2 */
-	IOMUX_MODE(MX31_PIN_GPIO1_3,	IOMUX_CONFIG_GPIO), /* 3 */
-	IOMUX_MODE(MX31_PIN_SVEN0,	IOMUX_CONFIG_GPIO), /* 32 */
-	IOMUX_MODE(MX31_PIN_STX0,	IOMUX_CONFIG_GPIO), /* 33 */
-	IOMUX_MODE(MX31_PIN_SRX0,	IOMUX_CONFIG_GPIO), /* 34 */
-	IOMUX_MODE(MX31_PIN_SIMPD0,	IOMUX_CONFIG_GPIO), /* 35 */
-	IOMUX_MODE(MX31_PIN_RTS1,	IOMUX_CONFIG_GPIO), /* 38 */
-	IOMUX_MODE(MX31_PIN_CTS1,	IOMUX_CONFIG_GPIO), /* 39 */
-	IOMUX_MODE(MX31_PIN_KEY_ROW4,	IOMUX_CONFIG_GPIO), /* 50 */
-	IOMUX_MODE(MX31_PIN_KEY_ROW5,	IOMUX_CONFIG_GPIO), /* 51 */
-	IOMUX_MODE(MX31_PIN_KEY_ROW6,	IOMUX_CONFIG_GPIO), /* 52 */
-	IOMUX_MODE(MX31_PIN_KEY_ROW7,	IOMUX_CONFIG_GPIO), /* 53 */
-
-	/* LEDs */
-	IOMUX_MODE(MX31_PIN_DTR_DTE1,	IOMUX_CONFIG_GPIO), /* 44 */
-	IOMUX_MODE(MX31_PIN_DSR_DTE1,	IOMUX_CONFIG_GPIO), /* 45 */
-	IOMUX_MODE(MX31_PIN_KEY_COL5,	IOMUX_CONFIG_GPIO), /* 55 */
-	IOMUX_MODE(MX31_PIN_KEY_COL6,	IOMUX_CONFIG_GPIO), /* 56 */
-};
-
-/* SPI */
-static struct spi_board_info pcm037_spi_dev[] = {
-	{
-		.modalias	= "dac124s085",
-		.max_speed_hz	= 400000,
-		.bus_num	= 0,
-		.chip_select	= 1,		/* Index in pcm037_spi1_cs[] */
-		.mode		= SPI_CPHA,
-	},
-};
-
-/* GPIO-keys input device */
-static struct gpio_keys_button pcm037_gpio_keys[] = {
-	{
-		.type	= EV_KEY,
-		.code	= KEY_L,
-		.gpio	= 0,
-		.desc	= "Wheel Manual",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_A,
-		.gpio	= 1,
-		.desc	= "Wheel AF",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_V,
-		.gpio	= 2,
-		.desc	= "Wheel View",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_M,
-		.gpio	= 3,
-		.desc	= "Wheel Menu",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_UP,
-		.gpio	= 32,
-		.desc	= "Nav Pad Up",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_RIGHT,
-		.gpio	= 33,
-		.desc	= "Nav Pad Right",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_DOWN,
-		.gpio	= 34,
-		.desc	= "Nav Pad Down",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_LEFT,
-		.gpio	= 35,
-		.desc	= "Nav Pad Left",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_ENTER,
-		.gpio	= 38,
-		.desc	= "Nav Pad Ok",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= KEY_O,
-		.gpio	= 39,
-		.desc	= "Wheel Off",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= BTN_FORWARD,
-		.gpio	= 50,
-		.desc	= "Focus Forward",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= BTN_BACK,
-		.gpio	= 51,
-		.desc	= "Focus Backward",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= BTN_MIDDLE,
-		.gpio	= 52,
-		.desc	= "Release Half",
-		.wakeup	= 0,
-	}, {
-		.type	= EV_KEY,
-		.code	= BTN_EXTRA,
-		.gpio	= 53,
-		.desc	= "Release Full",
-		.wakeup	= 0,
-	},
-};
-
-static const struct gpio_keys_platform_data
-		pcm037_gpio_keys_platform_data __initconst = {
-	.buttons	= pcm037_gpio_keys,
-	.nbuttons	= ARRAY_SIZE(pcm037_gpio_keys),
-	.rep		= 0, /* No auto-repeat */
-};
-
-int __init pcm037_eet_init_devices(void)
-{
-	if (pcm037_variant() != PCM037_EET)
-		return 0;
-
-	mxc_iomux_setup_multiple_pins(pcm037_eet_pins,
-				ARRAY_SIZE(pcm037_eet_pins), "pcm037_eet");
-
-	/* SPI */
-	spi_register_board_info(pcm037_spi_dev, ARRAY_SIZE(pcm037_spi_dev));
-	imx31_add_spi_imx0(NULL);
-
-	imx_add_gpio_keys(&pcm037_gpio_keys_platform_data);
-
-	return 0;
-}
diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c
deleted file mode 100644
index 017a50113005..000000000000
--- a/arch/arm/mach-imx/mach-pcm043.c
+++ /dev/null
@@ -1,412 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2009 Sascha Hauer, Pengutronix
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/smc911x.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-#include "ulpi.h"
-
-static const struct fb_videomode fb_modedb[] = {
-	{
-		/* 240x320 @ 60 Hz */
-		.name		= "Sharp-LQ035Q7",
-		.refresh	= 60,
-		.xres		= 240,
-		.yres		= 320,
-		.pixclock	= 185925,
-		.left_margin	= 9,
-		.right_margin	= 16,
-		.upper_margin	= 7,
-		.lower_margin	= 9,
-		.hsync_len	= 1,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}, {
-		/* 240x320 @ 60 Hz */
-		.name		= "TX090",
-		.refresh	= 60,
-		.xres		= 240,
-		.yres		= 320,
-		.pixclock	= 38255,
-		.left_margin	= 144,
-		.right_margin	= 0,
-		.upper_margin	= 7,
-		.lower_margin	= 40,
-		.hsync_len	= 96,
-		.vsync_len	= 1,
-		.sync		= FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	},
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
-	.name		= "Sharp-LQ035Q7",
-	.mode		= fb_modedb,
-	.num_modes	= ARRAY_SIZE(fb_modedb),
-};
-
-static struct physmap_flash_data pcm043_flash_data = {
-	.width  = 2,
-};
-
-static struct resource pcm043_flash_resource = {
-	.start	= 0xa0000000,
-	.end	= 0xa1ffffff,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device pcm043_flash = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &pcm043_flash_data,
-	},
-	.resource = &pcm043_flash_resource,
-	.num_resources = 1,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct imxi2c_platform_data pcm043_i2c0_data __initconst = {
-	.bitrate = 50000,
-};
-
-static const struct property_entry board_eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 32),
-	{ }
-};
-
-static struct i2c_board_info pcm043_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */
-		.properties = board_eeprom_properties,
-	}, {
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	},
-};
-
-static struct platform_device *devices[] __initdata = {
-	&pcm043_flash,
-};
-
-static const iomux_v3_cfg_t pcm043_pads[] __initconst = {
-	/* UART1 */
-	MX35_PAD_CTS1__UART1_CTS,
-	MX35_PAD_RTS1__UART1_RTS,
-	MX35_PAD_TXD1__UART1_TXD_MUX,
-	MX35_PAD_RXD1__UART1_RXD_MUX,
-	/* UART2 */
-	MX35_PAD_CTS2__UART2_CTS,
-	MX35_PAD_RTS2__UART2_RTS,
-	MX35_PAD_TXD2__UART2_TXD_MUX,
-	MX35_PAD_RXD2__UART2_RXD_MUX,
-	/* FEC */
-	MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
-	MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
-	MX35_PAD_FEC_RX_DV__FEC_RX_DV,
-	MX35_PAD_FEC_COL__FEC_COL,
-	MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
-	MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
-	MX35_PAD_FEC_TX_EN__FEC_TX_EN,
-	MX35_PAD_FEC_MDC__FEC_MDC,
-	MX35_PAD_FEC_MDIO__FEC_MDIO,
-	MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
-	MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
-	MX35_PAD_FEC_CRS__FEC_CRS,
-	MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
-	MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
-	MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
-	MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
-	MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
-	MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
-	/* I2C1 */
-	MX35_PAD_I2C1_CLK__I2C1_SCL,
-	MX35_PAD_I2C1_DAT__I2C1_SDA,
-	/* Display */
-	MX35_PAD_LD0__IPU_DISPB_DAT_0,
-	MX35_PAD_LD1__IPU_DISPB_DAT_1,
-	MX35_PAD_LD2__IPU_DISPB_DAT_2,
-	MX35_PAD_LD3__IPU_DISPB_DAT_3,
-	MX35_PAD_LD4__IPU_DISPB_DAT_4,
-	MX35_PAD_LD5__IPU_DISPB_DAT_5,
-	MX35_PAD_LD6__IPU_DISPB_DAT_6,
-	MX35_PAD_LD7__IPU_DISPB_DAT_7,
-	MX35_PAD_LD8__IPU_DISPB_DAT_8,
-	MX35_PAD_LD9__IPU_DISPB_DAT_9,
-	MX35_PAD_LD10__IPU_DISPB_DAT_10,
-	MX35_PAD_LD11__IPU_DISPB_DAT_11,
-	MX35_PAD_LD12__IPU_DISPB_DAT_12,
-	MX35_PAD_LD13__IPU_DISPB_DAT_13,
-	MX35_PAD_LD14__IPU_DISPB_DAT_14,
-	MX35_PAD_LD15__IPU_DISPB_DAT_15,
-	MX35_PAD_LD16__IPU_DISPB_DAT_16,
-	MX35_PAD_LD17__IPU_DISPB_DAT_17,
-	MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC,
-	MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
-	MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
-	MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
-	MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC,
-	MX35_PAD_D3_REV__IPU_DISPB_D3_REV,
-	MX35_PAD_D3_CLS__IPU_DISPB_D3_CLS,
-	/* gpio */
-	MX35_PAD_ATA_CS0__GPIO2_6,
-	/* USB host */
-	MX35_PAD_I2C2_CLK__USB_TOP_USBH2_PWR,
-	MX35_PAD_I2C2_DAT__USB_TOP_USBH2_OC,
-	/* SSI */
-	MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS,
-	MX35_PAD_STXD4__AUDMUX_AUD4_TXD,
-	MX35_PAD_SRXD4__AUDMUX_AUD4_RXD,
-	MX35_PAD_SCK4__AUDMUX_AUD4_TXC,
-	/* CAN2 */
-	MX35_PAD_TX5_RX0__CAN2_TXCAN,
-	MX35_PAD_TX4_RX1__CAN2_RXCAN,
-	/* esdhc */
-	MX35_PAD_SD1_CMD__ESDHC1_CMD,
-	MX35_PAD_SD1_CLK__ESDHC1_CLK,
-	MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
-	MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
-	MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
-	MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
-	MX35_PAD_ATA_DATA10__GPIO2_23, /* WriteProtect */
-	MX35_PAD_ATA_DATA11__GPIO2_24, /* CardDetect */
-};
-
-#define AC97_GPIO_TXFS	IMX_GPIO_NR(2, 31)
-#define AC97_GPIO_TXD	IMX_GPIO_NR(2, 28)
-#define AC97_GPIO_RESET	IMX_GPIO_NR(2, 0)
-
-static void pcm043_ac97_warm_reset(struct snd_ac97 *ac97)
-{
-	iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31;
-	iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS;
-	int ret;
-
-	ret = gpio_request(AC97_GPIO_TXFS, "SSI");
-	if (ret) {
-		printk("failed to get GPIO_TXFS: %d\n", ret);
-		return;
-	}
-
-	mxc_iomux_v3_setup_pad(txfs_gpio);
-
-	/* warm reset */
-	gpio_direction_output(AC97_GPIO_TXFS, 1);
-	udelay(2);
-	gpio_set_value(AC97_GPIO_TXFS, 0);
-
-	gpio_free(AC97_GPIO_TXFS);
-	mxc_iomux_v3_setup_pad(txfs);
-}
-
-static void pcm043_ac97_cold_reset(struct snd_ac97 *ac97)
-{
-	iomux_v3_cfg_t txfs_gpio = MX35_PAD_STXFS4__GPIO2_31;
-	iomux_v3_cfg_t txfs = MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS;
-	iomux_v3_cfg_t txd_gpio = MX35_PAD_STXD4__GPIO2_28;
-	iomux_v3_cfg_t txd = MX35_PAD_STXD4__AUDMUX_AUD4_TXD;
-	iomux_v3_cfg_t reset_gpio = MX35_PAD_SD2_CMD__GPIO2_0;
-	int ret;
-
-	ret = gpio_request(AC97_GPIO_TXFS, "SSI");
-	if (ret)
-		goto err1;
-
-	ret = gpio_request(AC97_GPIO_TXD, "SSI");
-	if (ret)
-		goto err2;
-
-	ret = gpio_request(AC97_GPIO_RESET, "SSI");
-	if (ret)
-		goto err3;
-
-	mxc_iomux_v3_setup_pad(txfs_gpio);
-	mxc_iomux_v3_setup_pad(txd_gpio);
-	mxc_iomux_v3_setup_pad(reset_gpio);
-
-	gpio_direction_output(AC97_GPIO_TXFS, 0);
-	gpio_direction_output(AC97_GPIO_TXD, 0);
-
-	/* cold reset */
-	gpio_direction_output(AC97_GPIO_RESET, 0);
-	udelay(10);
-	gpio_direction_output(AC97_GPIO_RESET, 1);
-
-	mxc_iomux_v3_setup_pad(txd);
-	mxc_iomux_v3_setup_pad(txfs);
-
-	gpio_free(AC97_GPIO_RESET);
-err3:
-	gpio_free(AC97_GPIO_TXD);
-err2:
-	gpio_free(AC97_GPIO_TXFS);
-err1:
-	if (ret)
-		printk("%s failed with %d\n", __func__, ret);
-	mdelay(1);
-}
-
-static const struct imx_ssi_platform_data pcm043_ssi_pdata __initconst = {
-	.ac97_reset = pcm043_ac97_cold_reset,
-	.ac97_warm_reset = pcm043_ac97_warm_reset,
-	.flags = IMX_SSI_USE_AC97,
-};
-
-static const struct mxc_nand_platform_data
-pcm037_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static int pcm043_otg_init(struct platform_device *pdev)
-{
-	return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static struct mxc_usbh_platform_data otg_pdata __initdata = {
-	.init	= pcm043_otg_init,
-	.portsc	= MXC_EHCI_MODE_UTMI,
-};
-
-static int pcm043_usbh1_init(struct platform_device *pdev)
-{
-	return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
-			MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN);
-}
-
-static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
-	.init	= pcm043_usbh1_init,
-	.portsc	= MXC_EHCI_MODE_SERIAL,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_UTMI,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init pcm043_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", pcm043_otg_mode);
-
-static struct esdhc_platform_data sd1_pdata = {
-	.wp_type = ESDHC_WP_GPIO,
-	.cd_type = ESDHC_CD_GPIO,
-};
-
-static struct gpiod_lookup_table sd1_gpio_table = {
-	.dev_id = "sdhci-esdhc-imx35.0",
-	.table = {
-		/* Card detect: bank 2 offset 24 */
-		GPIO_LOOKUP("imx35-gpio.2", 24, "cd", GPIO_ACTIVE_LOW),
-		/* Write protect: bank 2 offset 23 */
-		GPIO_LOOKUP("imx35-gpio.2", 23, "wp", GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-/*
- * Board specific initialization.
- */
-static void __init pcm043_init(void)
-{
-	imx35_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(pcm043_pads, ARRAY_SIZE(pcm043_pads));
-
-	imx35_add_fec(NULL);
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-	imx35_add_imx2_wdt();
-
-	imx35_add_imx_uart0(&uart_pdata);
-	imx35_add_mxc_nand(&pcm037_nand_board_info);
-
-	imx35_add_imx_uart1(&uart_pdata);
-
-	i2c_register_board_info(0, pcm043_i2c_devices,
-			ARRAY_SIZE(pcm043_i2c_devices));
-
-	imx35_add_imx_i2c0(&pcm043_i2c0_data);
-
-	imx35_add_ipu_core();
-	imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-
-	if (otg_mode_host) {
-		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-				ULPI_OTG_DRVVBUS_EXT);
-		if (otg_pdata.otg)
-			imx35_add_mxc_ehci_otg(&otg_pdata);
-	}
-	imx35_add_mxc_ehci_hs(&usbh1_pdata);
-
-	if (!otg_mode_host)
-		imx35_add_fsl_usb2_udc(&otg_device_pdata);
-
-	imx35_add_flexcan1();
-}
-
-static void __init pcm043_late_init(void)
-{
-	imx35_add_imx_ssi(0, &pcm043_ssi_pdata);
-
-	gpiod_add_lookup_table(&sd1_gpio_table);
-	imx35_add_sdhci_esdhc_imx(0, &sd1_pdata);
-}
-
-static void __init pcm043_timer_init(void)
-{
-	mx35_clocks_init();
-}
-
-MACHINE_START(PCM043, "Phytec Phycore pcm043")
-	/* Maintainer: Pengutronix */
-	.atag_offset = 0x100,
-	.map_io = mx35_map_io,
-	.init_early = imx35_init_early,
-	.init_irq = mx35_init_irq,
-	.init_time = pcm043_timer_init,
-	.init_machine	= pcm043_init,
-	.init_late	= pcm043_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-qong.c b/arch/arm/mach-imx/mach-qong.c
deleted file mode 100644
index 5b362da2dc09..000000000000
--- a/arch/arm/mach-imx/mach-qong.c
+++ /dev/null
@@ -1,262 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  Copyright (C) 2009 Ilya Yanok, Emcraft Systems Ltd, <yanok@emcraft.com>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/memory.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/platnand.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-#include <asm/page.h>
-#include <asm/setup.h>
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/* FPGA defines */
-#define QONG_FPGA_VERSION(major, minor, rev)	\
-	(((major & 0xF) << 12) | ((minor & 0xF) << 8) | (rev & 0xFF))
-
-#define QONG_FPGA_BASEADDR		MX31_CS1_BASE_ADDR
-#define QONG_FPGA_PERIPH_SIZE		(1 << 24)
-
-#define QONG_FPGA_CTRL_BASEADDR		QONG_FPGA_BASEADDR
-#define QONG_FPGA_CTRL_SIZE		0x10
-/* FPGA control registers */
-#define QONG_FPGA_CTRL_VERSION		0x00
-
-#define QONG_DNET_ID		1
-#define QONG_DNET_BASEADDR	\
-	(QONG_FPGA_BASEADDR + QONG_DNET_ID * QONG_FPGA_PERIPH_SIZE)
-#define QONG_DNET_SIZE		0x00001000
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static int uart_pins[] = {
-	MX31_PIN_CTS1__CTS1,
-	MX31_PIN_RTS1__RTS1,
-	MX31_PIN_TXD1__TXD1,
-	MX31_PIN_RXD1__RXD1
-};
-
-static inline void __init mxc_init_imx_uart(void)
-{
-	mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins),
-			"uart-0");
-	imx31_add_imx_uart0(&uart_pdata);
-}
-
-static struct resource dnet_resources[] = {
-	{
-		.name	= "dnet-memory",
-		.start	= QONG_DNET_BASEADDR,
-		.end	= QONG_DNET_BASEADDR + QONG_DNET_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device dnet_device = {
-	.name			= "dnet",
-	.id			= -1,
-	.num_resources		= ARRAY_SIZE(dnet_resources),
-	.resource		= dnet_resources,
-};
-
-static int __init qong_init_dnet(void)
-{
-	int ret;
-
-	dnet_resources[1].start =
-		gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1));
-	dnet_resources[1].end =
-		gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1));
-	ret = platform_device_register(&dnet_device);
-	return ret;
-}
-
-/* MTD NOR flash */
-
-static struct physmap_flash_data qong_flash_data = {
-	.width = 2,
-};
-
-static struct resource qong_flash_resource = {
-	.start = MX31_CS0_BASE_ADDR,
-	.end = MX31_CS0_BASE_ADDR + SZ_128M - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device qong_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &qong_flash_data,
-		},
-	.resource = &qong_flash_resource,
-	.num_resources = 1,
-};
-
-static void qong_init_nor_mtd(void)
-{
-	(void)platform_device_register(&qong_nor_mtd_device);
-}
-
-/*
- * Hardware specific access to control-lines
- */
-static void qong_nand_cmd_ctrl(struct nand_chip *nand_chip, int cmd,
-			       unsigned int ctrl)
-{
-	if (cmd == NAND_CMD_NONE)
-		return;
-
-	if (ctrl & NAND_CLE)
-		writeb(cmd, nand_chip->legacy.IO_ADDR_W + (1 << 24));
-	else
-		writeb(cmd, nand_chip->legacy.IO_ADDR_W + (1 << 23));
-}
-
-/*
- * Read the Device Ready pin.
- */
-static int qong_nand_device_ready(struct nand_chip *chip)
-{
-	return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_NFRB));
-}
-
-static void qong_nand_select_chip(struct nand_chip *chip, int cs)
-{
-	if (cs >= 0)
-		gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 0);
-	else
-		gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 1);
-}
-
-static struct platform_nand_data qong_nand_data = {
-	.chip = {
-		.nr_chips		= 1,
-		.chip_delay		= 20,
-		.options		= 0,
-	},
-	.ctrl = {
-		.cmd_ctrl		= qong_nand_cmd_ctrl,
-		.dev_ready		= qong_nand_device_ready,
-		.select_chip		= qong_nand_select_chip,
-	}
-};
-
-static struct resource qong_nand_resource = {
-	.start		= MX31_CS3_BASE_ADDR,
-	.end		= MX31_CS3_BASE_ADDR + SZ_32M - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device qong_nand_device = {
-	.name		= "gen_nand",
-	.id		= -1,
-	.dev		= {
-		.platform_data = &qong_nand_data,
-	},
-	.num_resources	= 1,
-	.resource	= &qong_nand_resource,
-};
-
-static void __init qong_init_nand_mtd(void)
-{
-	/* init CS */
-	imx_writel(0x00004f00, MX31_IO_ADDRESS(MX31_WEIM_CSCRxU(3)));
-	imx_writel(0x20013b31, MX31_IO_ADDRESS(MX31_WEIM_CSCRxL(3)));
-	imx_writel(0x00020800, MX31_IO_ADDRESS(MX31_WEIM_CSCRxA(3)));
-
-	mxc_iomux_set_gpr(MUX_SDCTL_CSD1_SEL, true);
-
-	/* enable pin */
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFCE_B, IOMUX_CONFIG_GPIO));
-	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), "nand_enable"))
-		gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 0);
-
-	/* ready/busy pin */
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFRB, IOMUX_CONFIG_GPIO));
-	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFRB), "nand_rdy"))
-		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFRB));
-
-	/* write protect pin */
-	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFWP_B, IOMUX_CONFIG_GPIO));
-	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFWP_B), "nand_wp"))
-		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFWP_B));
-
-	platform_device_register(&qong_nand_device);
-}
-
-static void __init qong_init_fpga(void)
-{
-	void __iomem *regs;
-	u32 fpga_ver;
-
-	regs = ioremap(QONG_FPGA_CTRL_BASEADDR, QONG_FPGA_CTRL_SIZE);
-	if (!regs) {
-		printk(KERN_ERR "%s: failed to map registers, aborting.\n",
-				__func__);
-		return;
-	}
-
-	fpga_ver = readl(regs + QONG_FPGA_CTRL_VERSION);
-	iounmap(regs);
-	printk(KERN_INFO "Qong FPGA version %d.%d.%d\n",
-			(fpga_ver & 0xF000) >> 12,
-			(fpga_ver & 0x0F00) >> 8, fpga_ver & 0x00FF);
-	if (fpga_ver < QONG_FPGA_VERSION(0, 8, 7)) {
-		printk(KERN_ERR "qong: Unexpected FPGA version, FPGA-based "
-				"devices won't be registered!\n");
-		return;
-	}
-
-	/* register FPGA-based devices */
-	qong_init_nand_mtd();
-	qong_init_dnet();
-}
-
-/*
- * Board specific initialization.
- */
-static void __init qong_init(void)
-{
-	imx31_soc_init();
-
-	mxc_init_imx_uart();
-	qong_init_nor_mtd();
-	imx31_add_imx2_wdt();
-}
-
-static void __init qong_timer_init(void)
-{
-	mx31_clocks_init(26000000);
-}
-
-MACHINE_START(QONG, "Dave/DENX QongEVB-LITE")
-	/* Maintainer: DENX Software Engineering GmbH */
-	.atag_offset = 0x100,
-	.map_io = mx31_map_io,
-	.init_early = imx31_init_early,
-	.init_irq = mx31_init_irq,
-	.init_time	= qong_timer_init,
-	.init_machine = qong_init,
-	.init_late	= qong_init_fpga,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c
deleted file mode 100644
index fae5a41b5f6c..000000000000
--- a/arch/arm/mach-imx/mach-vpr200.c
+++ /dev/null
@@ -1,306 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Marc Kleine-Budde, Pengutronix
- * Copyright 2010 Creative Product Design
- *
- * Derived from mx35 3stack.
- * Original author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/memory.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include <linux/i2c.h>
-#include <linux/mfd/mc13xxx.h>
-
-#include "common.h"
-#include "devices-imx35.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx35.h"
-
-#define GPIO_LCDPWR	IMX_GPIO_NR(1, 2)
-#define GPIO_PMIC_INT	IMX_GPIO_NR(2, 0)
-
-#define GPIO_BUTTON1	IMX_GPIO_NR(1, 4)
-#define GPIO_BUTTON2	IMX_GPIO_NR(1, 5)
-#define GPIO_BUTTON3	IMX_GPIO_NR(1, 7)
-#define GPIO_BUTTON4	IMX_GPIO_NR(1, 8)
-#define GPIO_BUTTON5	IMX_GPIO_NR(1, 9)
-#define GPIO_BUTTON6	IMX_GPIO_NR(1, 10)
-#define GPIO_BUTTON7	IMX_GPIO_NR(1, 11)
-#define GPIO_BUTTON8	IMX_GPIO_NR(1, 12)
-
-static const struct fb_videomode fb_modedb[] = {
-	{
-		/* 800x480 @ 60 Hz */
-		.name		= "PT0708048",
-		.refresh	= 60,
-		.xres		= 800,
-		.yres		= 480,
-		.pixclock	= KHZ2PICOS(33260),
-		.left_margin	= 50,
-		.right_margin	= 156,
-		.upper_margin	= 10,
-		.lower_margin	= 10,
-		.hsync_len	= 1,	/* note: DE only display */
-		.vsync_len	= 1,	/* note: DE only display */
-		.sync		= FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}, {
-		/* 800x480 @ 60 Hz */
-		.name		= "CTP-CLAA070LC0ACW",
-		.refresh	= 60,
-		.xres		= 800,
-		.yres		= 480,
-		.pixclock	= KHZ2PICOS(27000),
-		.left_margin	= 50,
-		.right_margin	= 50,	/* whole line should have 900 clocks */
-		.upper_margin	= 10,
-		.lower_margin	= 10,	/* whole frame should have 500 lines */
-		.hsync_len	= 1,	/* note: DE only display */
-		.vsync_len	= 1,	/* note: DE only display */
-		.sync		= FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
-		.vmode		= FB_VMODE_NONINTERLACED,
-		.flag		= 0,
-	}
-};
-
-static struct mx3fb_platform_data mx3fb_pdata __initdata = {
-	.name		= "PT0708048",
-	.mode		= fb_modedb,
-	.num_modes	= ARRAY_SIZE(fb_modedb),
-};
-
-static struct physmap_flash_data vpr200_flash_data = {
-	.width  = 2,
-};
-
-static struct resource vpr200_flash_resource = {
-	.start	= MX35_CS0_BASE_ADDR,
-	.end	= MX35_CS0_BASE_ADDR + SZ_64M - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device vpr200_flash = {
-	.name	= "physmap-flash",
-	.id	= 0,
-	.dev	= {
-		.platform_data  = &vpr200_flash_data,
-	},
-	.resource = &vpr200_flash_resource,
-	.num_resources = 1,
-};
-
-static const struct mxc_nand_platform_data
-		vpr200_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-	.flash_bbt = 1,
-};
-
-#define VPR_KEY_DEBOUNCE	500
-static struct gpio_keys_button vpr200_gpio_keys_table[] = {
-	{KEY_F2, GPIO_BUTTON1, 1, "vpr-keys: F2", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F3, GPIO_BUTTON2, 1, "vpr-keys: F3", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F4, GPIO_BUTTON3, 1, "vpr-keys: F4", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F5, GPIO_BUTTON4, 1, "vpr-keys: F5", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F6, GPIO_BUTTON5, 1, "vpr-keys: F6", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F7, GPIO_BUTTON6, 1, "vpr-keys: F7", 0, VPR_KEY_DEBOUNCE},
-	{KEY_F8, GPIO_BUTTON7, 1, "vpr-keys: F8", 1, VPR_KEY_DEBOUNCE},
-	{KEY_F9, GPIO_BUTTON8, 1, "vpr-keys: F9", 1, VPR_KEY_DEBOUNCE},
-};
-
-static const struct gpio_keys_platform_data
-		vpr200_gpio_keys_data __initconst = {
-	.buttons = vpr200_gpio_keys_table,
-	.nbuttons = ARRAY_SIZE(vpr200_gpio_keys_table),
-};
-
-static struct mc13xxx_platform_data vpr200_pmic = {
-	.flags = MC13XXX_USE_ADC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static const struct imxi2c_platform_data vpr200_i2c0_data __initconst = {
-	.bitrate = 50000,
-};
-
-static struct i2c_board_info vpr200_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c02", 0x50), /* E0=0, E1=0, E2=0 */
-	}, {
-		I2C_BOARD_INFO("mc13892", 0x08),
-		.platform_data = &vpr200_pmic,
-		/* irq number is run-time assigned */
-	}
-};
-
-static const iomux_v3_cfg_t vpr200_pads[] __initconst = {
-	/* UART1 */
-	MX35_PAD_TXD1__UART1_TXD_MUX,
-	MX35_PAD_RXD1__UART1_RXD_MUX,
-	/* UART3 */
-	MX35_PAD_ATA_DATA10__UART3_RXD_MUX,
-	MX35_PAD_ATA_DATA11__UART3_TXD_MUX,
-	/* FEC */
-	MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
-	MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
-	MX35_PAD_FEC_RX_DV__FEC_RX_DV,
-	MX35_PAD_FEC_COL__FEC_COL,
-	MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
-	MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
-	MX35_PAD_FEC_TX_EN__FEC_TX_EN,
-	MX35_PAD_FEC_MDC__FEC_MDC,
-	MX35_PAD_FEC_MDIO__FEC_MDIO,
-	MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
-	MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
-	MX35_PAD_FEC_CRS__FEC_CRS,
-	MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
-	MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
-	MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
-	MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
-	MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
-	MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
-	/* Display */
-	MX35_PAD_LD0__IPU_DISPB_DAT_0,
-	MX35_PAD_LD1__IPU_DISPB_DAT_1,
-	MX35_PAD_LD2__IPU_DISPB_DAT_2,
-	MX35_PAD_LD3__IPU_DISPB_DAT_3,
-	MX35_PAD_LD4__IPU_DISPB_DAT_4,
-	MX35_PAD_LD5__IPU_DISPB_DAT_5,
-	MX35_PAD_LD6__IPU_DISPB_DAT_6,
-	MX35_PAD_LD7__IPU_DISPB_DAT_7,
-	MX35_PAD_LD8__IPU_DISPB_DAT_8,
-	MX35_PAD_LD9__IPU_DISPB_DAT_9,
-	MX35_PAD_LD10__IPU_DISPB_DAT_10,
-	MX35_PAD_LD11__IPU_DISPB_DAT_11,
-	MX35_PAD_LD12__IPU_DISPB_DAT_12,
-	MX35_PAD_LD13__IPU_DISPB_DAT_13,
-	MX35_PAD_LD14__IPU_DISPB_DAT_14,
-	MX35_PAD_LD15__IPU_DISPB_DAT_15,
-	MX35_PAD_LD16__IPU_DISPB_DAT_16,
-	MX35_PAD_LD17__IPU_DISPB_DAT_17,
-	MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
-	MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
-	MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
-	/* LCD Enable */
-	MX35_PAD_D3_VSYNC__GPIO1_2,
-	/* USBOTG */
-	MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
-	MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
-	/* SDCARD */
-	MX35_PAD_SD1_CMD__ESDHC1_CMD,
-	MX35_PAD_SD1_CLK__ESDHC1_CLK,
-	MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
-	MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
-	MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
-	MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
-	/* PMIC */
-	MX35_PAD_GPIO2_0__GPIO2_0,
-	/* GPIO keys */
-	MX35_PAD_SCKR__GPIO1_4,
-	MX35_PAD_COMPARE__GPIO1_5,
-	MX35_PAD_SCKT__GPIO1_7,
-	MX35_PAD_FST__GPIO1_8,
-	MX35_PAD_HCKT__GPIO1_9,
-	MX35_PAD_TX5_RX0__GPIO1_10,
-	MX35_PAD_TX4_RX1__GPIO1_11,
-	MX35_PAD_TX3_RX2__GPIO1_12,
-};
-
-/* USB Device config */
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_UTMI,
-	.workaround	= FLS_USB2_WORKAROUND_ENGCM09152,
-};
-
-static int vpr200_usbh_init(struct platform_device *pdev)
-{
-	return mx35_initialize_usb_hw(pdev->id,
-			MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY);
-}
-
-/* USB HOST config */
-static const struct mxc_usbh_platform_data usb_host_pdata __initconst = {
-	.init = vpr200_usbh_init,
-	.portsc = MXC_EHCI_MODE_SERIAL,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&vpr200_flash,
-};
-
-/*
- * Board specific initialization.
- */
-static void __init vpr200_board_init(void)
-{
-	imx35_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(vpr200_pads, ARRAY_SIZE(vpr200_pads));
-
-	imx35_add_fec(NULL);
-	imx35_add_imx2_wdt();
-
-	imx35_add_imx_uart0(NULL);
-	imx35_add_imx_uart2(NULL);
-
-	imx35_add_ipu_core();
-	imx35_add_mx3_sdc_fb(&mx3fb_pdata);
-
-	imx35_add_fsl_usb2_udc(&otg_device_pdata);
-	imx35_add_mxc_ehci_hs(&usb_host_pdata);
-
-	imx35_add_mxc_nand(&vpr200_nand_board_info);
-	imx35_add_sdhci_esdhc_imx(0, NULL);
-}
-
-static void __init vpr200_late_init(void)
-{
-	imx_add_gpio_keys(&vpr200_gpio_keys_data);
-
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	if (0 != gpio_request(GPIO_LCDPWR, "LCDPWR"))
-		printk(KERN_WARNING "vpr200: Couldn't get LCDPWR gpio\n");
-	else
-		gpio_direction_output(GPIO_LCDPWR, 0);
-
-	if (0 != gpio_request(GPIO_PMIC_INT, "PMIC_INT"))
-		printk(KERN_WARNING "vpr200: Couldn't get PMIC_INT gpio\n");
-	else
-		gpio_direction_input(GPIO_PMIC_INT);
-
-	vpr200_i2c_devices[1].irq = gpio_to_irq(GPIO_PMIC_INT);
-	i2c_register_board_info(0, vpr200_i2c_devices,
-			ARRAY_SIZE(vpr200_i2c_devices));
-
-	imx35_add_imx_i2c0(&vpr200_i2c0_data);
-}
-
-static void __init vpr200_timer_init(void)
-{
-	mx35_clocks_init();
-}
-
-MACHINE_START(VPR200, "VPR200")
-	/* Maintainer: Creative Product Design */
-	.map_io = mx35_map_io,
-	.init_early = imx35_init_early,
-	.init_irq = mx35_init_irq,
-	.init_time = vpr200_timer_init,
-	.init_machine = vpr200_board_init,
-	.init_late	= vpr200_late_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mm-imx21.c b/arch/arm/mach-imx/mm-imx21.c
deleted file mode 100644
index b834026e4615..000000000000
--- a/arch/arm/mach-imx/mm-imx21.c
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/mach-imx/mm-imx21.c
- *
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/pinctrl/machine.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices/devices-common.h"
-#include "hardware.h"
-#include "iomux-v1.h"
-
-/* MX21 memory map definition */
-static struct map_desc imx21_io_desc[] __initdata = {
-	/*
-	 * this fixed mapping covers:
-	 * - AIPI1
-	 * - AIPI2
-	 * - AITC
-	 * - ROM Patch
-	 * - and some reserved space
-	 */
-	imx_map_entry(MX21, AIPI, MT_DEVICE),
-	/*
-	 * this fixed mapping covers:
-	 * - CSI
-	 * - ATA
-	 */
-	imx_map_entry(MX21, SAHB1, MT_DEVICE),
-	/*
-	 * this fixed mapping covers:
-	 * - EMI
-	 */
-	imx_map_entry(MX21, X_MEMC, MT_DEVICE),
-};
-
-/*
- * Initialize the memory map. It is called during the
- * system startup to create static physical to virtual
- * memory map for the IO modules.
- */
-void __init mx21_map_io(void)
-{
-	iotable_init(imx21_io_desc, ARRAY_SIZE(imx21_io_desc));
-}
-
-void __init imx21_init_early(void)
-{
-	mxc_set_cpu_type(MXC_CPU_MX21);
-	imx_iomuxv1_init(MX21_IO_ADDRESS(MX21_GPIO_BASE_ADDR),
-			MX21_NUM_GPIO_PORT);
-}
-
-void __init mx21_init_irq(void)
-{
-	mxc_init_irq(MX21_IO_ADDRESS(MX21_AVIC_BASE_ADDR));
-}
-
-static const struct resource imx21_audmux_res[] __initconst = {
-	DEFINE_RES_MEM(MX21_AUDMUX_BASE_ADDR, SZ_4K),
-};
-
-void __init imx21_soc_init(void)
-{
-	mxc_arch_reset_init(MX21_IO_ADDRESS(MX21_WDOG_BASE_ADDR));
-	mxc_device_init();
-
-	mxc_register_gpio("imx21-gpio", 0, MX21_GPIO1_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 1, MX21_GPIO2_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 2, MX21_GPIO3_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 3, MX21_GPIO4_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 4, MX21_GPIO5_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 5, MX21_GPIO6_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
-
-	pinctrl_provide_dummies();
-	imx_add_imx_dma("imx21-dma", MX21_DMA_BASE_ADDR, MX21_INT_DMACH0);
-	platform_device_register_simple("imx21-audmux", 0, imx21_audmux_res,
-					ARRAY_SIZE(imx21_audmux_res));
-}
diff --git a/arch/arm/mach-imx/mm-imx27.c b/arch/arm/mach-imx/mm-imx27.c
deleted file mode 100644
index 2717614f101d..000000000000
--- a/arch/arm/mach-imx/mm-imx27.c
+++ /dev/null
@@ -1,88 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/mach-imx/mm-imx27.c
- *
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/pinctrl/machine.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices/devices-common.h"
-#include "hardware.h"
-#include "iomux-v1.h"
-
-/* MX27 memory map definition */
-static struct map_desc imx27_io_desc[] __initdata = {
-	/*
-	 * this fixed mapping covers:
-	 * - AIPI1
-	 * - AIPI2
-	 * - AITC
-	 * - ROM Patch
-	 * - and some reserved space
-	 */
-	imx_map_entry(MX27, AIPI, MT_DEVICE),
-	/*
-	 * this fixed mapping covers:
-	 * - CSI
-	 * - ATA
-	 */
-	imx_map_entry(MX27, SAHB1, MT_DEVICE),
-	/*
-	 * this fixed mapping covers:
-	 * - EMI
-	 */
-	imx_map_entry(MX27, X_MEMC, MT_DEVICE),
-};
-
-/*
- * Initialize the memory map. It is called during the
- * system startup to create static physical to virtual
- * memory map for the IO modules.
- */
-void __init mx27_map_io(void)
-{
-	iotable_init(imx27_io_desc, ARRAY_SIZE(imx27_io_desc));
-}
-
-void __init imx27_init_early(void)
-{
-	mxc_set_cpu_type(MXC_CPU_MX27);
-	imx_iomuxv1_init(MX27_IO_ADDRESS(MX27_GPIO_BASE_ADDR),
-			MX27_NUM_GPIO_PORT);
-}
-
-void __init mx27_init_irq(void)
-{
-	mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
-}
-
-static const struct resource imx27_audmux_res[] __initconst = {
-	DEFINE_RES_MEM(MX27_AUDMUX_BASE_ADDR, SZ_4K),
-};
-
-void __init imx27_soc_init(void)
-{
-	mxc_arch_reset_init(MX27_IO_ADDRESS(MX27_WDOG_BASE_ADDR));
-	mxc_device_init();
-
-	/* i.mx27 has the i.mx21 type gpio */
-	mxc_register_gpio("imx21-gpio", 0, MX27_GPIO1_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 1, MX27_GPIO2_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 2, MX27_GPIO3_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 3, MX27_GPIO4_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 4, MX27_GPIO5_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-	mxc_register_gpio("imx21-gpio", 5, MX27_GPIO6_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
-
-	pinctrl_provide_dummies();
-	imx_add_imx_dma("imx27-dma", MX27_DMA_BASE_ADDR, MX27_INT_DMACH0);
-	/* imx27 has the imx21 type audmux */
-	platform_device_register_simple("imx21-audmux", 0, imx27_audmux_res,
-					ARRAY_SIZE(imx27_audmux_res));
-
-	imx27_pm_init();
-}
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index ea2d58a63903..5056438e5b42 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -11,6 +11,7 @@
 #include <linux/init.h>
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/of_address.h>
 #include <linux/pinctrl/machine.h>
 
 #include <asm/system_misc.h>
@@ -19,9 +20,7 @@
 
 #include "common.h"
 #include "crmregs-imx3.h"
-#include "devices/devices-common.h"
 #include "hardware.h"
-#include "iomux-v3.h"
 
 void __iomem *mx3_ccm_base;
 
@@ -71,40 +70,6 @@ static void __iomem *imx3_ioremap_caller(phys_addr_t phys_addr, size_t size,
 	return __arm_ioremap_caller(phys_addr, size, mtype, caller);
 }
 
-static void __init imx3_init_l2x0(void)
-{
-#ifdef CONFIG_CACHE_L2X0
-	void __iomem *l2x0_base;
-	void __iomem *clkctl_base;
-
-/*
- * First of all, we must repair broken chip settings. There are some
- * i.MX35 CPUs in the wild, comming with bogus L2 cache settings. These
- * misconfigured CPUs will run amok immediately when the L2 cache gets enabled.
- * Workaraound is to setup the correct register setting prior enabling the
- * L2 cache. This should not hurt already working CPUs, as they are using the
- * same value.
- */
-#define L2_MEM_VAL 0x10
-
-	clkctl_base = ioremap(MX35_CLKCTL_BASE_ADDR, 4096);
-	if (clkctl_base != NULL) {
-		writel(0x00000515, clkctl_base + L2_MEM_VAL);
-		iounmap(clkctl_base);
-	} else {
-		pr_err("L2 cache: Cannot fix timing. Trying to continue without\n");
-	}
-
-	l2x0_base = ioremap(MX3x_L2CC_BASE_ADDR, 4096);
-	if (!l2x0_base) {
-		printk(KERN_ERR "remapping L2 cache area failed\n");
-		return;
-	}
-
-	l2x0_init(l2x0_base, 0x00030024, 0x00000000);
-#endif
-}
-
 #ifdef CONFIG_SOC_IMX31
 static struct map_desc mx31_io_desc[] __initdata = {
 	imx_map_entry(MX31, X_MEMC, MT_DEVICE),
@@ -135,70 +100,26 @@ static void imx31_idle(void)
 
 void __init imx31_init_early(void)
 {
+	struct device_node *np;
+
 	mxc_set_cpu_type(MXC_CPU_MX31);
 	arch_ioremap_caller = imx3_ioremap_caller;
 	arm_pm_idle = imx31_idle;
-	mx3_ccm_base = MX31_IO_ADDRESS(MX31_CCM_BASE_ADDR);
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-ccm");
+	mx3_ccm_base = of_iomap(np, 0);
+	BUG_ON(!mx3_ccm_base);
 }
 
 void __init mx31_init_irq(void)
 {
-	mxc_init_irq(MX31_IO_ADDRESS(MX31_AVIC_BASE_ADDR));
-}
-
-static struct sdma_script_start_addrs imx31_to1_sdma_script __initdata = {
-	.per_2_per_addr = 1677,
-};
-
-static struct sdma_script_start_addrs imx31_to2_sdma_script __initdata = {
-	.ap_2_ap_addr = 423,
-	.ap_2_bp_addr = 829,
-	.bp_2_ap_addr = 1029,
-};
-
-static struct sdma_platform_data imx31_sdma_pdata __initdata = {
-	.fw_name = "sdma-imx31-to2.bin",
-	.script_addrs = &imx31_to2_sdma_script,
-};
-
-static const struct resource imx31_audmux_res[] __initconst = {
-	DEFINE_RES_MEM(MX31_AUDMUX_BASE_ADDR, SZ_16K),
-};
-
-static const struct resource imx31_rnga_res[] __initconst = {
-	DEFINE_RES_MEM(MX31_RNGA_BASE_ADDR, SZ_16K),
-};
-
-void __init imx31_soc_init(void)
-{
-	int to_version = mx31_revision() >> 4;
+	void __iomem *avic_base;
+	struct device_node *np;
 
-	imx3_init_l2x0();
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-avic");
+	avic_base = of_iomap(np, 0);
+	BUG_ON(!avic_base);
 
-	mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
-	mxc_device_init();
-
-	mxc_register_gpio("imx31-gpio", 0, MX31_GPIO1_BASE_ADDR, SZ_16K, MX31_INT_GPIO1, 0);
-	mxc_register_gpio("imx31-gpio", 1, MX31_GPIO2_BASE_ADDR, SZ_16K, MX31_INT_GPIO2, 0);
-	mxc_register_gpio("imx31-gpio", 2, MX31_GPIO3_BASE_ADDR, SZ_16K, MX31_INT_GPIO3, 0);
-
-	pinctrl_provide_dummies();
-
-	if (to_version == 1) {
-		strncpy(imx31_sdma_pdata.fw_name, "sdma-imx31-to1.bin",
-			strlen(imx31_sdma_pdata.fw_name));
-		imx31_sdma_pdata.script_addrs = &imx31_to1_sdma_script;
-	}
-
-	imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata);
-
-	imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS1_BASE_ADDR));
-	imx_set_aips(MX31_IO_ADDRESS(MX31_AIPS2_BASE_ADDR));
-
-	platform_device_register_simple("imx31-audmux", 0, imx31_audmux_res,
-					ARRAY_SIZE(imx31_audmux_res));
-	platform_device_register_simple("mxc_rnga", -1, imx31_rnga_res,
-					ARRAY_SIZE(imx31_rnga_res));
+	mxc_init_irq(avic_base);
 }
 #endif /* ifdef CONFIG_SOC_IMX31 */
 
@@ -228,85 +149,25 @@ static void imx35_idle(void)
 
 void __init imx35_init_early(void)
 {
+	struct device_node *np;
+
 	mxc_set_cpu_type(MXC_CPU_MX35);
-	mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
 	arm_pm_idle = imx35_idle;
 	arch_ioremap_caller = imx3_ioremap_caller;
-	mx3_ccm_base = MX35_IO_ADDRESS(MX35_CCM_BASE_ADDR);
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-ccm");
+	mx3_ccm_base = of_iomap(np, 0);
+	BUG_ON(!mx3_ccm_base);
 }
 
 void __init mx35_init_irq(void)
 {
-	mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR));
-}
-
-static struct sdma_script_start_addrs imx35_to1_sdma_script __initdata = {
-	.ap_2_ap_addr = 642,
-	.uart_2_mcu_addr = 817,
-	.mcu_2_app_addr = 747,
-	.uartsh_2_mcu_addr = 1183,
-	.per_2_shp_addr = 1033,
-	.mcu_2_shp_addr = 961,
-	.ata_2_mcu_addr = 1333,
-	.mcu_2_ata_addr = 1252,
-	.app_2_mcu_addr = 683,
-	.shp_2_per_addr = 1111,
-	.shp_2_mcu_addr = 892,
-};
-
-static struct sdma_script_start_addrs imx35_to2_sdma_script __initdata = {
-	.ap_2_ap_addr = 729,
-	.uart_2_mcu_addr = 904,
-	.per_2_app_addr = 1597,
-	.mcu_2_app_addr = 834,
-	.uartsh_2_mcu_addr = 1270,
-	.per_2_shp_addr = 1120,
-	.mcu_2_shp_addr = 1048,
-	.ata_2_mcu_addr = 1429,
-	.mcu_2_ata_addr = 1339,
-	.app_2_per_addr = 1531,
-	.app_2_mcu_addr = 770,
-	.shp_2_per_addr = 1198,
-	.shp_2_mcu_addr = 979,
-};
-
-static struct sdma_platform_data imx35_sdma_pdata __initdata = {
-	.fw_name = "sdma-imx35-to2.bin",
-	.script_addrs = &imx35_to2_sdma_script,
-};
-
-static const struct resource imx35_audmux_res[] __initconst = {
-	DEFINE_RES_MEM(MX35_AUDMUX_BASE_ADDR, SZ_16K),
-};
-
-void __init imx35_soc_init(void)
-{
-	int to_version = mx35_revision() >> 4;
-
-	imx3_init_l2x0();
-
-	mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
-	mxc_device_init();
-
-	mxc_register_gpio("imx35-gpio", 0, MX35_GPIO1_BASE_ADDR, SZ_16K, MX35_INT_GPIO1, 0);
-	mxc_register_gpio("imx35-gpio", 1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
-	mxc_register_gpio("imx35-gpio", 2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
-
-	pinctrl_provide_dummies();
-	if (to_version == 1) {
-		strncpy(imx35_sdma_pdata.fw_name, "sdma-imx35-to1.bin",
-			strlen(imx35_sdma_pdata.fw_name));
-		imx35_sdma_pdata.script_addrs = &imx35_to1_sdma_script;
-	}
-
-	imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata);
+	void __iomem *avic_base;
+	struct device_node *np;
 
-	/* Setup AIPS registers */
-	imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS1_BASE_ADDR));
-	imx_set_aips(MX35_IO_ADDRESS(MX35_AIPS2_BASE_ADDR));
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-avic");
+	avic_base = of_iomap(np, 0);
+	BUG_ON(!avic_base);
 
-	/* i.mx35 has the i.mx31 type audmux */
-	platform_device_register_simple("imx31-audmux", 0, imx35_audmux_res,
-					ARRAY_SIZE(imx35_audmux_res));
+	mxc_init_irq(avic_base);
 }
 #endif /* ifdef CONFIG_SOC_IMX35 */
diff --git a/arch/arm/mach-imx/mx21.h b/arch/arm/mach-imx/mx21.h
deleted file mode 100644
index 38be12a44bdd..000000000000
--- a/arch/arm/mach-imx/mx21.h
+++ /dev/null
@@ -1,176 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
- * Copyright 2009 Holger Schurig, hs4233@mail.mn-solutions.de
- *
- * This contains i.MX21-specific hardware definitions. For those
- * hardware pieces that are common between i.MX21 and i.MX27, have a
- * look at mx2x.h.
- */
-
-#ifndef __MACH_MX21_H__
-#define __MACH_MX21_H__
-
-#define MX21_AIPI_BASE_ADDR		0x10000000
-#define MX21_AIPI_SIZE			SZ_1M
-#define MX21_DMA_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x01000)
-#define MX21_WDOG_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x02000)
-#define MX21_GPT1_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x03000)
-#define MX21_GPT2_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x04000)
-#define MX21_GPT3_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x05000)
-#define MX21_PWM_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x06000)
-#define MX21_RTC_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x07000)
-#define MX21_KPP_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x08000)
-#define MX21_OWIRE_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x09000)
-#define MX21_UART1_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0a000)
-#define MX21_UART2_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0b000)
-#define MX21_UART3_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0c000)
-#define MX21_UART4_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0d000)
-#define MX21_CSPI1_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0e000)
-#define MX21_CSPI2_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x0f000)
-#define MX21_SSI1_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x10000)
-#define MX21_SSI2_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x11000)
-#define MX21_I2C_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x12000)
-#define MX21_SDHC1_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x13000)
-#define MX21_SDHC2_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x14000)
-#define MX21_GPIO_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x15000)
-#define MX21_GPIO1_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x000)
-#define MX21_GPIO2_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x100)
-#define MX21_GPIO3_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x200)
-#define MX21_GPIO4_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x300)
-#define MX21_GPIO5_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x400)
-#define MX21_GPIO6_BASE_ADDR			(MX21_GPIO_BASE_ADDR + 0x500)
-#define MX21_AUDMUX_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x16000)
-#define MX21_CSPI3_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x17000)
-#define MX21_LCDC_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x21000)
-#define MX21_SLCDC_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x22000)
-#define MX21_USBOTG_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x24000)
-#define MX21_EMMA_PP_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x26000)
-#define MX21_EMMA_PRP_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x26400)
-#define MX21_CCM_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x27000)
-#define MX21_SYSCTRL_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x27800)
-#define MX21_JAM_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x3e000)
-#define MX21_MAX_BASE_ADDR			(MX21_AIPI_BASE_ADDR + 0x3f000)
-
-#define MX21_AVIC_BASE_ADDR		0x10040000
-
-#define MX21_SAHB1_BASE_ADDR		0x80000000
-#define MX21_SAHB1_SIZE			SZ_1M
-#define MX21_CSI_BASE_ADDR			(MX2x_SAHB1_BASE_ADDR + 0x0000)
-
-/* Memory regions and CS */
-#define MX21_SDRAM_BASE_ADDR		0xc0000000
-#define MX21_CSD1_BASE_ADDR		0xc4000000
-
-#define MX21_CS0_BASE_ADDR		0xc8000000
-#define MX21_CS1_BASE_ADDR		0xcc000000
-#define MX21_CS2_BASE_ADDR		0xd0000000
-#define MX21_CS3_BASE_ADDR		0xd1000000
-#define MX21_CS4_BASE_ADDR		0xd2000000
-#define MX21_PCMCIA_MEM_BASE_ADDR	0xd4000000
-#define MX21_CS5_BASE_ADDR		0xdd000000
-
-/* NAND, SDRAM, WEIM etc controllers */
-#define MX21_X_MEMC_BASE_ADDR		0xdf000000
-#define MX21_X_MEMC_SIZE		SZ_256K
-
-#define MX21_SDRAMC_BASE_ADDR		(MX21_X_MEMC_BASE_ADDR + 0x0000)
-#define MX21_EIM_BASE_ADDR		(MX21_X_MEMC_BASE_ADDR + 0x1000)
-#define MX21_PCMCIA_CTL_BASE_ADDR	(MX21_X_MEMC_BASE_ADDR + 0x2000)
-#define MX21_NFC_BASE_ADDR		(MX21_X_MEMC_BASE_ADDR + 0x3000)
-
-#define MX21_IRAM_BASE_ADDR		0xffffe800	/* internal ram */
-
-#define MX21_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX21_IO_ADDRESS(x)		IOMEM(MX21_IO_P2V(x))
-
-/* fixed interrupt numbers */
-#include <asm/irq.h>
-#define MX21_INT_CSPI3		(NR_IRQS_LEGACY + 6)
-#define MX21_INT_GPIO		(NR_IRQS_LEGACY + 8)
-#define MX21_INT_FIRI		(NR_IRQS_LEGACY + 9)
-#define MX21_INT_SDHC2		(NR_IRQS_LEGACY + 10)
-#define MX21_INT_SDHC1		(NR_IRQS_LEGACY + 11)
-#define MX21_INT_I2C		(NR_IRQS_LEGACY + 12)
-#define MX21_INT_SSI2		(NR_IRQS_LEGACY + 13)
-#define MX21_INT_SSI1		(NR_IRQS_LEGACY + 14)
-#define MX21_INT_CSPI2		(NR_IRQS_LEGACY + 15)
-#define MX21_INT_CSPI1		(NR_IRQS_LEGACY + 16)
-#define MX21_INT_UART4		(NR_IRQS_LEGACY + 17)
-#define MX21_INT_UART3		(NR_IRQS_LEGACY + 18)
-#define MX21_INT_UART2		(NR_IRQS_LEGACY + 19)
-#define MX21_INT_UART1		(NR_IRQS_LEGACY + 20)
-#define MX21_INT_KPP		(NR_IRQS_LEGACY + 21)
-#define MX21_INT_RTC		(NR_IRQS_LEGACY + 22)
-#define MX21_INT_PWM		(NR_IRQS_LEGACY + 23)
-#define MX21_INT_GPT3		(NR_IRQS_LEGACY + 24)
-#define MX21_INT_GPT2		(NR_IRQS_LEGACY + 25)
-#define MX21_INT_GPT1		(NR_IRQS_LEGACY + 26)
-#define MX21_INT_WDOG		(NR_IRQS_LEGACY + 27)
-#define MX21_INT_PCMCIA		(NR_IRQS_LEGACY + 28)
-#define MX21_INT_NFC		(NR_IRQS_LEGACY + 29)
-#define MX21_INT_BMI		(NR_IRQS_LEGACY + 30)
-#define MX21_INT_CSI		(NR_IRQS_LEGACY + 31)
-#define MX21_INT_DMACH0		(NR_IRQS_LEGACY + 32)
-#define MX21_INT_DMACH1		(NR_IRQS_LEGACY + 33)
-#define MX21_INT_DMACH2		(NR_IRQS_LEGACY + 34)
-#define MX21_INT_DMACH3		(NR_IRQS_LEGACY + 35)
-#define MX21_INT_DMACH4		(NR_IRQS_LEGACY + 36)
-#define MX21_INT_DMACH5		(NR_IRQS_LEGACY + 37)
-#define MX21_INT_DMACH6		(NR_IRQS_LEGACY + 38)
-#define MX21_INT_DMACH7		(NR_IRQS_LEGACY + 39)
-#define MX21_INT_DMACH8		(NR_IRQS_LEGACY + 40)
-#define MX21_INT_DMACH9		(NR_IRQS_LEGACY + 41)
-#define MX21_INT_DMACH10	(NR_IRQS_LEGACY + 42)
-#define MX21_INT_DMACH11	(NR_IRQS_LEGACY + 43)
-#define MX21_INT_DMACH12	(NR_IRQS_LEGACY + 44)
-#define MX21_INT_DMACH13	(NR_IRQS_LEGACY + 45)
-#define MX21_INT_DMACH14	(NR_IRQS_LEGACY + 46)
-#define MX21_INT_DMACH15	(NR_IRQS_LEGACY + 47)
-#define MX21_INT_EMMAENC	(NR_IRQS_LEGACY + 49)
-#define MX21_INT_EMMADEC	(NR_IRQS_LEGACY + 50)
-#define MX21_INT_EMMAPRP	(NR_IRQS_LEGACY + 51)
-#define MX21_INT_EMMAPP		(NR_IRQS_LEGACY + 52)
-#define MX21_INT_USBWKUP	(NR_IRQS_LEGACY + 53)
-#define MX21_INT_USBDMA		(NR_IRQS_LEGACY + 54)
-#define MX21_INT_USBHOST	(NR_IRQS_LEGACY + 55)
-#define MX21_INT_USBFUNC	(NR_IRQS_LEGACY + 56)
-#define MX21_INT_USBMNP		(NR_IRQS_LEGACY + 57)
-#define MX21_INT_USBCTRL	(NR_IRQS_LEGACY + 58)
-#define MX21_INT_SLCDC		(NR_IRQS_LEGACY + 60)
-#define MX21_INT_LCDC		(NR_IRQS_LEGACY + 61)
-
-/* fixed DMA request numbers */
-#define MX21_DMA_REQ_CSPI3_RX	1
-#define MX21_DMA_REQ_CSPI3_TX	2
-#define MX21_DMA_REQ_EXT	3
-#define MX21_DMA_REQ_FIRI_RX	4
-#define MX21_DMA_REQ_SDHC2	6
-#define MX21_DMA_REQ_SDHC1	7
-#define MX21_DMA_REQ_SSI2_RX0	8
-#define MX21_DMA_REQ_SSI2_TX0	9
-#define MX21_DMA_REQ_SSI2_RX1	10
-#define MX21_DMA_REQ_SSI2_TX1	11
-#define MX21_DMA_REQ_SSI1_RX0	12
-#define MX21_DMA_REQ_SSI1_TX0	13
-#define MX21_DMA_REQ_SSI1_RX1	14
-#define MX21_DMA_REQ_SSI1_TX1	15
-#define MX21_DMA_REQ_CSPI2_RX	16
-#define MX21_DMA_REQ_CSPI2_TX	17
-#define MX21_DMA_REQ_CSPI1_RX	18
-#define MX21_DMA_REQ_CSPI1_TX	19
-#define MX21_DMA_REQ_UART4_RX	20
-#define MX21_DMA_REQ_UART4_TX	21
-#define MX21_DMA_REQ_UART3_RX	22
-#define MX21_DMA_REQ_UART3_TX	23
-#define MX21_DMA_REQ_UART2_RX	24
-#define MX21_DMA_REQ_UART2_TX	25
-#define MX21_DMA_REQ_UART1_RX	26
-#define MX21_DMA_REQ_UART1_TX	27
-#define MX21_DMA_REQ_BMI_TX	28
-#define MX21_DMA_REQ_BMI_RX	29
-#define MX21_DMA_REQ_CSI_STAT	30
-#define MX21_DMA_REQ_CSI_RX	31
-
-#endif /* ifndef __MACH_MX21_H__ */
diff --git a/arch/arm/mach-imx/mx27.h b/arch/arm/mach-imx/mx27.h
index c6f7aae02b67..241c04d706fe 100644
--- a/arch/arm/mach-imx/mx27.h
+++ b/arch/arm/mach-imx/mx27.h
@@ -13,209 +13,13 @@
 
 #define MX27_AIPI_BASE_ADDR		0x10000000
 #define MX27_AIPI_SIZE			SZ_1M
-#define MX27_DMA_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x01000)
-#define MX27_WDOG_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x02000)
-#define MX27_GPT1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x03000)
-#define MX27_GPT2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x04000)
-#define MX27_GPT3_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x05000)
-#define MX27_PWM_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x06000)
-#define MX27_RTC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x07000)
-#define MX27_KPP_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x08000)
-#define MX27_OWIRE_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x09000)
-#define MX27_UART1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0a000)
-#define MX27_UART2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0b000)
-#define MX27_UART3_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0c000)
-#define MX27_UART4_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0d000)
-#define MX27_CSPI1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0e000)
-#define MX27_CSPI2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x0f000)
-#define MX27_SSI1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x10000)
-#define MX27_SSI2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x11000)
-#define MX27_I2C1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x12000)
-#define MX27_SDHC1_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x13000)
-#define MX27_SDHC2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x14000)
-#define MX27_GPIO_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x15000)
-#define MX27_GPIO1_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x000)
-#define MX27_GPIO2_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x100)
-#define MX27_GPIO3_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x200)
-#define MX27_GPIO4_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x300)
-#define MX27_GPIO5_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x400)
-#define MX27_GPIO6_BASE_ADDR			(MX27_GPIO_BASE_ADDR + 0x500)
-#define MX27_AUDMUX_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x16000)
-#define MX27_CSPI3_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x17000)
-#define MX27_MSHC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x18000)
-#define MX27_GPT4_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x19000)
-#define MX27_GPT5_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1a000)
-#define MX27_UART5_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1b000)
-#define MX27_UART6_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1c000)
-#define MX27_I2C2_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1d000)
-#define MX27_SDHC3_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1e000)
-#define MX27_GPT6_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x1f000)
-#define MX27_LCDC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x21000)
-#define MX27_SLCDC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x22000)
-#define MX27_VPU_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x23000)
-#define MX27_USB_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x24000)
-#define MX27_USB_OTG_BASE_ADDR			(MX27_USB_BASE_ADDR + 0x0000)
-#define MX27_USB_HS1_BASE_ADDR			(MX27_USB_BASE_ADDR + 0x0200)
-#define MX27_USB_HS2_BASE_ADDR			(MX27_USB_BASE_ADDR + 0x0400)
-#define MX27_SAHARA_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x25000)
-#define MX27_EMMAPP_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x26000)
-#define MX27_EMMAPRP_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x26400)
-#define MX27_CCM_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x27000)
-#define MX27_SYSCTRL_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x27800)
-#define MX27_IIM_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x28000)
-#define MX27_RTIC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x2a000)
-#define MX27_FEC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x2b000)
-#define MX27_SCC_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x2c000)
-#define MX27_ETB_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x3b000)
-#define MX27_ETB_RAM_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x3c000)
-#define MX27_JAM_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x3e000)
-#define MX27_MAX_BASE_ADDR			(MX27_AIPI_BASE_ADDR + 0x3f000)
-
-#define MX27_AVIC_BASE_ADDR		0x10040000
-
-/* ROM patch */
-#define MX27_ROMP_BASE_ADDR		0x10041000
 
 #define MX27_SAHB1_BASE_ADDR		0x80000000
 #define MX27_SAHB1_SIZE			SZ_1M
-#define MX27_CSI_BASE_ADDR			(MX27_SAHB1_BASE_ADDR + 0x0000)
-#define MX27_ATA_BASE_ADDR			(MX27_SAHB1_BASE_ADDR + 0x1000)
-
-/* Memory regions and CS */
-#define MX27_SDRAM_BASE_ADDR		0xa0000000
-#define MX27_CSD1_BASE_ADDR		0xb0000000
 
-#define MX27_CS0_BASE_ADDR		0xc0000000
-#define MX27_CS1_BASE_ADDR		0xc8000000
-#define MX27_CS2_BASE_ADDR		0xd0000000
-#define MX27_CS3_BASE_ADDR		0xd2000000
-#define MX27_CS4_BASE_ADDR		0xd4000000
-#define MX27_CS5_BASE_ADDR		0xd6000000
-
-/* NAND, SDRAM, WEIM, M3IF, EMI controllers */
 #define MX27_X_MEMC_BASE_ADDR		0xd8000000
 #define MX27_X_MEMC_SIZE		SZ_1M
-#define MX27_NFC_BASE_ADDR			(MX27_X_MEMC_BASE_ADDR)
-#define MX27_SDRAMC_BASE_ADDR			(MX27_X_MEMC_BASE_ADDR + 0x1000)
-#define MX27_WEIM_BASE_ADDR			(MX27_X_MEMC_BASE_ADDR + 0x2000)
-#define MX27_M3IF_BASE_ADDR			(MX27_X_MEMC_BASE_ADDR + 0x3000)
-#define MX27_PCMCIA_CTL_BASE_ADDR		(MX27_X_MEMC_BASE_ADDR + 0x4000)
-
-#define MX27_WEIM_CSCRx_BASE_ADDR(cs)	(MX27_WEIM_BASE_ADDR + (cs) * 0x10)
-#define MX27_WEIM_CSCRxU(cs)			(MX27_WEIM_CSCRx_BASE_ADDR(cs))
-#define MX27_WEIM_CSCRxL(cs)			(MX27_WEIM_CSCRx_BASE_ADDR(cs) + 0x4)
-#define MX27_WEIM_CSCRxA(cs)			(MX27_WEIM_CSCRx_BASE_ADDR(cs) + 0x8)
-
-#define MX27_PCMCIA_MEM_BASE_ADDR	0xdc000000
-
-/* IRAM */
-#define MX27_IRAM_BASE_ADDR		0xffff4c00	/* internal ram */
 
 #define MX27_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX27_IO_ADDRESS(x)		IOMEM(MX27_IO_P2V(x))
-
-/* fixed interrupt numbers */
-#include <asm/irq.h>
-#define MX27_INT_I2C2		(NR_IRQS_LEGACY + 1)
-#define MX27_INT_GPT6		(NR_IRQS_LEGACY + 2)
-#define MX27_INT_GPT5		(NR_IRQS_LEGACY + 3)
-#define MX27_INT_GPT4		(NR_IRQS_LEGACY + 4)
-#define MX27_INT_RTIC		(NR_IRQS_LEGACY + 5)
-#define MX27_INT_CSPI3		(NR_IRQS_LEGACY + 6)
-#define MX27_INT_MSHC		(NR_IRQS_LEGACY + 7)
-#define MX27_INT_GPIO		(NR_IRQS_LEGACY + 8)
-#define MX27_INT_SDHC3		(NR_IRQS_LEGACY + 9)
-#define MX27_INT_SDHC2		(NR_IRQS_LEGACY + 10)
-#define MX27_INT_SDHC1		(NR_IRQS_LEGACY + 11)
-#define MX27_INT_I2C1		(NR_IRQS_LEGACY + 12)
-#define MX27_INT_SSI2		(NR_IRQS_LEGACY + 13)
-#define MX27_INT_SSI1		(NR_IRQS_LEGACY + 14)
-#define MX27_INT_CSPI2		(NR_IRQS_LEGACY + 15)
-#define MX27_INT_CSPI1		(NR_IRQS_LEGACY + 16)
-#define MX27_INT_UART4		(NR_IRQS_LEGACY + 17)
-#define MX27_INT_UART3		(NR_IRQS_LEGACY + 18)
-#define MX27_INT_UART2		(NR_IRQS_LEGACY + 19)
-#define MX27_INT_UART1		(NR_IRQS_LEGACY + 20)
-#define MX27_INT_KPP		(NR_IRQS_LEGACY + 21)
-#define MX27_INT_RTC		(NR_IRQS_LEGACY + 22)
-#define MX27_INT_PWM		(NR_IRQS_LEGACY + 23)
-#define MX27_INT_GPT3		(NR_IRQS_LEGACY + 24)
-#define MX27_INT_GPT2		(NR_IRQS_LEGACY + 25)
-#define MX27_INT_GPT1		(NR_IRQS_LEGACY + 26)
-#define MX27_INT_WDOG		(NR_IRQS_LEGACY + 27)
-#define MX27_INT_PCMCIA		(NR_IRQS_LEGACY + 28)
-#define MX27_INT_NFC		(NR_IRQS_LEGACY + 29)
-#define MX27_INT_ATA		(NR_IRQS_LEGACY + 30)
-#define MX27_INT_CSI		(NR_IRQS_LEGACY + 31)
-#define MX27_INT_DMACH0		(NR_IRQS_LEGACY + 32)
-#define MX27_INT_DMACH1		(NR_IRQS_LEGACY + 33)
-#define MX27_INT_DMACH2		(NR_IRQS_LEGACY + 34)
-#define MX27_INT_DMACH3		(NR_IRQS_LEGACY + 35)
-#define MX27_INT_DMACH4		(NR_IRQS_LEGACY + 36)
-#define MX27_INT_DMACH5		(NR_IRQS_LEGACY + 37)
-#define MX27_INT_DMACH6		(NR_IRQS_LEGACY + 38)
-#define MX27_INT_DMACH7		(NR_IRQS_LEGACY + 39)
-#define MX27_INT_DMACH8		(NR_IRQS_LEGACY + 40)
-#define MX27_INT_DMACH9		(NR_IRQS_LEGACY + 41)
-#define MX27_INT_DMACH10	(NR_IRQS_LEGACY + 42)
-#define MX27_INT_DMACH11	(NR_IRQS_LEGACY + 43)
-#define MX27_INT_DMACH12	(NR_IRQS_LEGACY + 44)
-#define MX27_INT_DMACH13	(NR_IRQS_LEGACY + 45)
-#define MX27_INT_DMACH14	(NR_IRQS_LEGACY + 46)
-#define MX27_INT_DMACH15	(NR_IRQS_LEGACY + 47)
-#define MX27_INT_UART6		(NR_IRQS_LEGACY + 48)
-#define MX27_INT_UART5		(NR_IRQS_LEGACY + 49)
-#define MX27_INT_FEC		(NR_IRQS_LEGACY + 50)
-#define MX27_INT_EMMAPRP	(NR_IRQS_LEGACY + 51)
-#define MX27_INT_EMMAPP		(NR_IRQS_LEGACY + 52)
-#define MX27_INT_VPU		(NR_IRQS_LEGACY + 53)
-#define MX27_INT_USB_HS1	(NR_IRQS_LEGACY + 54)
-#define MX27_INT_USB_HS2	(NR_IRQS_LEGACY + 55)
-#define MX27_INT_USB_OTG	(NR_IRQS_LEGACY + 56)
-#define MX27_INT_SCC_SMN	(NR_IRQS_LEGACY + 57)
-#define MX27_INT_SCC_SCM	(NR_IRQS_LEGACY + 58)
-#define MX27_INT_SAHARA		(NR_IRQS_LEGACY + 59)
-#define MX27_INT_SLCDC		(NR_IRQS_LEGACY + 60)
-#define MX27_INT_LCDC		(NR_IRQS_LEGACY + 61)
-#define MX27_INT_IIM		(NR_IRQS_LEGACY + 62)
-#define MX27_INT_CCM		(NR_IRQS_LEGACY + 63)
-
-/* fixed DMA request numbers */
-#define MX27_DMA_REQ_CSPI3_RX	1
-#define MX27_DMA_REQ_CSPI3_TX	2
-#define MX27_DMA_REQ_EXT	3
-#define MX27_DMA_REQ_MSHC	4
-#define MX27_DMA_REQ_SDHC2	6
-#define MX27_DMA_REQ_SDHC1	7
-#define MX27_DMA_REQ_SSI2_RX0	8
-#define MX27_DMA_REQ_SSI2_TX0	9
-#define MX27_DMA_REQ_SSI2_RX1	10
-#define MX27_DMA_REQ_SSI2_TX1	11
-#define MX27_DMA_REQ_SSI1_RX0	12
-#define MX27_DMA_REQ_SSI1_TX0	13
-#define MX27_DMA_REQ_SSI1_RX1	14
-#define MX27_DMA_REQ_SSI1_TX1	15
-#define MX27_DMA_REQ_CSPI2_RX	16
-#define MX27_DMA_REQ_CSPI2_TX	17
-#define MX27_DMA_REQ_CSPI1_RX	18
-#define MX27_DMA_REQ_CSPI1_TX	19
-#define MX27_DMA_REQ_UART4_RX	20
-#define MX27_DMA_REQ_UART4_TX	21
-#define MX27_DMA_REQ_UART3_RX	22
-#define MX27_DMA_REQ_UART3_TX	23
-#define MX27_DMA_REQ_UART2_RX	24
-#define MX27_DMA_REQ_UART2_TX	25
-#define MX27_DMA_REQ_UART1_RX	26
-#define MX27_DMA_REQ_UART1_TX	27
-#define MX27_DMA_REQ_ATA_TX	28
-#define MX27_DMA_REQ_ATA_RCV	29
-#define MX27_DMA_REQ_CSI_STAT	30
-#define MX27_DMA_REQ_CSI_RX	31
-#define MX27_DMA_REQ_UART5_TX	32
-#define MX27_DMA_REQ_UART5_RX	33
-#define MX27_DMA_REQ_UART6_TX	34
-#define MX27_DMA_REQ_UART6_RX	35
-#define MX27_DMA_REQ_SDHC3	36
-#define MX27_DMA_REQ_NFC	37
 
 #endif /* ifndef __MACH_MX27_H__ */
diff --git a/arch/arm/mach-imx/mx31.h b/arch/arm/mach-imx/mx31.h
index d9574671ca5c..08a72e25c289 100644
--- a/arch/arm/mach-imx/mx31.h
+++ b/arch/arm/mach-imx/mx31.h
@@ -2,196 +2,17 @@
 #ifndef __MACH_MX31_H__
 #define __MACH_MX31_H__
 
-/*
- * IRAM
- */
-#define MX31_IRAM_BASE_ADDR		0x1ffc0000	/* internal ram */
-#define MX31_IRAM_SIZE			SZ_16K
-
-#define MX31_L2CC_BASE_ADDR		0x30000000
-#define MX31_L2CC_SIZE			SZ_1M
-
 #define MX31_AIPS1_BASE_ADDR		0x43f00000
 #define MX31_AIPS1_SIZE			SZ_1M
-#define MX31_MAX_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x04000)
-#define MX31_EVTMON_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x08000)
-#define MX31_CLKCTL_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x0c000)
-#define MX31_ETB_SLOT4_BASE_ADDR		(MX31_AIPS1_BASE_ADDR + 0x10000)
-#define MX31_ETB_SLOT5_BASE_ADDR		(MX31_AIPS1_BASE_ADDR + 0x14000)
-#define MX31_ECT_CTIO_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x18000)
-#define MX31_I2C1_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x80000)
-#define MX31_I2C3_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x84000)
-#define MX31_USB_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x88000)
-#define MX31_USB_OTG_BASE_ADDR			(MX31_USB_BASE_ADDR + 0x0000)
-#define MX31_USB_HS1_BASE_ADDR			(MX31_USB_BASE_ADDR + 0x0200)
-#define MX31_USB_HS2_BASE_ADDR			(MX31_USB_BASE_ADDR + 0x0400)
-#define MX31_ATA_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x8c000)
-#define MX31_UART1_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x90000)
-#define MX31_UART2_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x94000)
-#define MX31_I2C2_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x98000)
-#define MX31_OWIRE_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0x9c000)
-#define MX31_SSI1_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xa0000)
-#define MX31_CSPI1_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xa4000)
-#define MX31_KPP_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xa8000)
-#define MX31_IOMUXC_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xac000)
-#define MX31_UART4_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xb0000)
-#define MX31_UART5_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xb4000)
-#define MX31_ECT_IP1_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xb8000)
-#define MX31_ECT_IP2_BASE_ADDR			(MX31_AIPS1_BASE_ADDR + 0xbc000)
-
 #define MX31_SPBA0_BASE_ADDR		0x50000000
 #define MX31_SPBA0_SIZE			SZ_1M
-#define MX31_SDHC1_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x04000)
-#define MX31_SDHC2_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x08000)
-#define MX31_UART3_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x0c000)
-#define MX31_CSPI2_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x10000)
-#define MX31_SSI2_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x14000)
-#define MX31_SIM1_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x18000)
-#define MX31_IIM_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x1c000)
-#define MX31_ATA_DMA_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x20000)
-#define MX31_MSHC1_BASE_ADDR			(MX31_SPBA0_BASE_ADDR + 0x24000)
-#define MX31_SPBA_CTRL_BASE_ADDR		(MX31_SPBA0_BASE_ADDR + 0x3c000)
-
 #define MX31_AIPS2_BASE_ADDR		0x53f00000
 #define MX31_AIPS2_SIZE			SZ_1M
-#define MX31_CCM_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x80000)
-#define MX31_CSPI3_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x84000)
-#define MX31_FIRI_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x8c000)
-#define MX31_GPT1_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x90000)
-#define MX31_EPIT1_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x94000)
-#define MX31_EPIT2_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0x98000)
-#define MX31_GPIO3_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xa4000)
-#define MX31_SCC_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xac000)
-#define MX31_SCM_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xae000)
-#define MX31_SMN_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xaf000)
-#define MX31_RNGA_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xb0000)
-#define MX31_IPU_CTRL_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xc0000)
-#define MX31_AUDMUX_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xc4000)
-#define MX31_MPEG4_ENC_BASE_ADDR		(MX31_AIPS2_BASE_ADDR + 0xc8000)
-#define MX31_GPIO1_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xcc000)
-#define MX31_GPIO2_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xd0000)
-#define MX31_SDMA_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xd4000)
-#define MX31_RTC_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xd8000)
-#define MX31_WDOG_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xdc000)
-#define MX31_PWM_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xe0000)
-#define MX31_RTIC_BASE_ADDR			(MX31_AIPS2_BASE_ADDR + 0xec000)
-
-#define MX31_ROMP_BASE_ADDR		0x60000000
-#define MX31_ROMP_BASE_ADDR_VIRT	IOMEM(0xfc500000)
-#define MX31_ROMP_SIZE			SZ_1M
-
 #define MX31_AVIC_BASE_ADDR		0x68000000
 #define MX31_AVIC_SIZE			SZ_1M
-
-#define MX31_IPU_MEM_BASE_ADDR		0x70000000
-#define MX31_CSD0_BASE_ADDR		0x80000000
-#define MX31_CSD1_BASE_ADDR		0x90000000
-
-#define MX31_CS0_BASE_ADDR		0xa0000000
-#define MX31_CS1_BASE_ADDR		0xa8000000
-#define MX31_CS2_BASE_ADDR		0xb0000000
-#define MX31_CS3_BASE_ADDR		0xb2000000
-
-#define MX31_CS4_BASE_ADDR		0xb4000000
-#define MX31_CS4_BASE_ADDR_VIRT		IOMEM(0xf6000000)
-#define MX31_CS4_SIZE			SZ_32M
-
-#define MX31_CS5_BASE_ADDR		0xb6000000
-#define MX31_CS5_BASE_ADDR_VIRT		IOMEM(0xf8000000)
-#define MX31_CS5_SIZE			SZ_32M
-
 #define MX31_X_MEMC_BASE_ADDR		0xb8000000
 #define MX31_X_MEMC_SIZE		SZ_64K
-#define MX31_NFC_BASE_ADDR			(MX31_X_MEMC_BASE_ADDR + 0x0000)
-#define MX31_ESDCTL_BASE_ADDR			(MX31_X_MEMC_BASE_ADDR + 0x1000)
-#define MX31_WEIM_BASE_ADDR			(MX31_X_MEMC_BASE_ADDR + 0x2000)
-#define MX31_M3IF_BASE_ADDR			(MX31_X_MEMC_BASE_ADDR + 0x3000)
-#define MX31_EMI_CTL_BASE_ADDR			(MX31_X_MEMC_BASE_ADDR + 0x4000)
-#define MX31_PCMCIA_CTL_BASE_ADDR		MX31_EMI_CTL_BASE_ADDR
-
-#define MX31_WEIM_CSCRx_BASE_ADDR(cs)	(MX31_WEIM_BASE_ADDR + (cs) * 0x10)
-#define MX31_WEIM_CSCRxU(cs)			(MX31_WEIM_CSCRx_BASE_ADDR(cs))
-#define MX31_WEIM_CSCRxL(cs)			(MX31_WEIM_CSCRx_BASE_ADDR(cs) + 0x4)
-#define MX31_WEIM_CSCRxA(cs)			(MX31_WEIM_CSCRx_BASE_ADDR(cs) + 0x8)
-
-#define MX31_PCMCIA_MEM_BASE_ADDR	0xbc000000
 
 #define MX31_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX31_IO_ADDRESS(x)		IOMEM(MX31_IO_P2V(x))
-
-/*
- * Interrupt numbers
- */
-#include <asm/irq.h>
-#define MX31_INT_I2C3		(NR_IRQS_LEGACY + 3)
-#define MX31_INT_I2C2		(NR_IRQS_LEGACY + 4)
-#define MX31_INT_MPEG4_ENCODER	(NR_IRQS_LEGACY + 5)
-#define MX31_INT_RTIC		(NR_IRQS_LEGACY + 6)
-#define MX31_INT_FIRI		(NR_IRQS_LEGACY + 7)
-#define MX31_INT_SDHC2		(NR_IRQS_LEGACY + 8)
-#define MX31_INT_SDHC1		(NR_IRQS_LEGACY + 9)
-#define MX31_INT_I2C1		(NR_IRQS_LEGACY + 10)
-#define MX31_INT_SSI2		(NR_IRQS_LEGACY + 11)
-#define MX31_INT_SSI1		(NR_IRQS_LEGACY + 12)
-#define MX31_INT_CSPI2		(NR_IRQS_LEGACY + 13)
-#define MX31_INT_CSPI1		(NR_IRQS_LEGACY + 14)
-#define MX31_INT_ATA		(NR_IRQS_LEGACY + 15)
-#define MX31_INT_MBX		(NR_IRQS_LEGACY + 16)
-#define MX31_INT_CSPI3		(NR_IRQS_LEGACY + 17)
-#define MX31_INT_UART3		(NR_IRQS_LEGACY + 18)
-#define MX31_INT_IIM		(NR_IRQS_LEGACY + 19)
-#define MX31_INT_SIM2		(NR_IRQS_LEGACY + 20)
-#define MX31_INT_SIM1		(NR_IRQS_LEGACY + 21)
-#define MX31_INT_RNGA		(NR_IRQS_LEGACY + 22)
-#define MX31_INT_EVTMON		(NR_IRQS_LEGACY + 23)
-#define MX31_INT_KPP		(NR_IRQS_LEGACY + 24)
-#define MX31_INT_RTC		(NR_IRQS_LEGACY + 25)
-#define MX31_INT_PWM		(NR_IRQS_LEGACY + 26)
-#define MX31_INT_EPIT2		(NR_IRQS_LEGACY + 27)
-#define MX31_INT_EPIT1		(NR_IRQS_LEGACY + 28)
-#define MX31_INT_GPT		(NR_IRQS_LEGACY + 29)
-#define MX31_INT_POWER_FAIL	(NR_IRQS_LEGACY + 30)
-#define MX31_INT_CCM_DVFS	(NR_IRQS_LEGACY + 31)
-#define MX31_INT_UART2		(NR_IRQS_LEGACY + 32)
-#define MX31_INT_NFC		(NR_IRQS_LEGACY + 33)
-#define MX31_INT_SDMA		(NR_IRQS_LEGACY + 34)
-#define MX31_INT_USB_HS1	(NR_IRQS_LEGACY + 35)
-#define MX31_INT_USB_HS2	(NR_IRQS_LEGACY + 36)
-#define MX31_INT_USB_OTG	(NR_IRQS_LEGACY + 37)
-#define MX31_INT_MSHC1		(NR_IRQS_LEGACY + 39)
-#define MX31_INT_MSHC2		(NR_IRQS_LEGACY + 40)
-#define MX31_INT_IPU_ERR	(NR_IRQS_LEGACY + 41)
-#define MX31_INT_IPU_SYN	(NR_IRQS_LEGACY + 42)
-#define MX31_INT_UART1		(NR_IRQS_LEGACY + 45)
-#define MX31_INT_UART4		(NR_IRQS_LEGACY + 46)
-#define MX31_INT_UART5		(NR_IRQS_LEGACY + 47)
-#define MX31_INT_ECT		(NR_IRQS_LEGACY + 48)
-#define MX31_INT_SCC_SCM	(NR_IRQS_LEGACY + 49)
-#define MX31_INT_SCC_SMN	(NR_IRQS_LEGACY + 50)
-#define MX31_INT_GPIO2		(NR_IRQS_LEGACY + 51)
-#define MX31_INT_GPIO1		(NR_IRQS_LEGACY + 52)
-#define MX31_INT_CCM		(NR_IRQS_LEGACY + 53)
-#define MX31_INT_PCMCIA		(NR_IRQS_LEGACY + 54)
-#define MX31_INT_WDOG		(NR_IRQS_LEGACY + 55)
-#define MX31_INT_GPIO3		(NR_IRQS_LEGACY + 56)
-#define MX31_INT_EXT_POWER	(NR_IRQS_LEGACY + 58)
-#define MX31_INT_EXT_TEMPER	(NR_IRQS_LEGACY + 59)
-#define MX31_INT_EXT_SENSOR60	(NR_IRQS_LEGACY + 60)
-#define MX31_INT_EXT_SENSOR61	(NR_IRQS_LEGACY + 61)
-#define MX31_INT_EXT_WDOG	(NR_IRQS_LEGACY + 62)
-#define MX31_INT_EXT_TV		(NR_IRQS_LEGACY + 63)
-
-#define MX31_DMA_REQ_SDHC1	20
-#define MX31_DMA_REQ_SDHC2	21
-#define MX31_DMA_REQ_SSI2_RX1	22
-#define MX31_DMA_REQ_SSI2_TX1	23
-#define MX31_DMA_REQ_SSI2_RX0	24
-#define MX31_DMA_REQ_SSI2_TX0	25
-#define MX31_DMA_REQ_SSI1_RX1	26
-#define MX31_DMA_REQ_SSI1_TX1	27
-#define MX31_DMA_REQ_SSI1_RX0	28
-#define MX31_DMA_REQ_SSI1_TX0	29
-
-#define MX31_PROD_SIGNATURE		0x1	/* For MX31 */
 
 #endif /* ifndef __MACH_MX31_H__ */
diff --git a/arch/arm/mach-imx/mx31lilly-db.c b/arch/arm/mach-imx/mx31lilly-db.c
deleted file mode 100644
index 00a5ee30d5dd..000000000000
--- a/arch/arm/mach-imx/mx31lilly-db.c
+++ /dev/null
@@ -1,182 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  LILLY-1131 development board support
- *
- *    Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- *  based on code for other MX31 boards,
- *
- *    Copyright 2005-2007 Freescale Semiconductor
- *    Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- *    Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lilly.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * This file contains board-specific initialization routines for the
- * LILLY-1131 development board. If you design an own baseboard for the
- * module, use this file as base for support code.
- */
-
-static unsigned int lilly_db_board_pins[] __initdata = {
-	MX31_PIN_SD1_DATA3__SD1_DATA3,
-	MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA1__SD1_DATA1,
-	MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_CLK__SD1_CLK,
-	MX31_PIN_SD1_CMD__SD1_CMD,
-	MX31_PIN_LD0__LD0,
-	MX31_PIN_LD1__LD1,
-	MX31_PIN_LD2__LD2,
-	MX31_PIN_LD3__LD3,
-	MX31_PIN_LD4__LD4,
-	MX31_PIN_LD5__LD5,
-	MX31_PIN_LD6__LD6,
-	MX31_PIN_LD7__LD7,
-	MX31_PIN_LD8__LD8,
-	MX31_PIN_LD9__LD9,
-	MX31_PIN_LD10__LD10,
-	MX31_PIN_LD11__LD11,
-	MX31_PIN_LD12__LD12,
-	MX31_PIN_LD13__LD13,
-	MX31_PIN_LD14__LD14,
-	MX31_PIN_LD15__LD15,
-	MX31_PIN_LD16__LD16,
-	MX31_PIN_LD17__LD17,
-	MX31_PIN_VSYNC3__VSYNC3,
-	MX31_PIN_HSYNC__HSYNC,
-	MX31_PIN_FPSHIFT__FPSHIFT,
-	MX31_PIN_DRDY0__DRDY0,
-	MX31_PIN_CONTRAST__CONTRAST,
-};
-
-/* MMC support */
-
-static int mxc_mmc1_get_ro(struct device *dev)
-{
-	return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_LCS0));
-}
-
-static int gpio_det, gpio_wp;
-
-#define MMC_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int mxc_mmc1_init(struct device *dev,
-			 irq_handler_t detect_irq, void *data)
-{
-	int ret;
-
-	gpio_det = IOMUX_TO_GPIO(MX31_PIN_GPIO1_1);
-	gpio_wp = IOMUX_TO_GPIO(MX31_PIN_LCS0);
-
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA0, MMC_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA1, MMC_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA2, MMC_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA3, MMC_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SD1_CLK, MMC_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SD1_CMD, MMC_PAD_CFG);
-
-	ret = gpio_request(gpio_det, "MMC detect");
-	if (ret)
-		return ret;
-
-	ret = gpio_request(gpio_wp, "MMC w/p");
-	if (ret)
-		goto exit_free_det;
-
-	gpio_direction_input(gpio_det);
-	gpio_direction_input(gpio_wp);
-
-	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)),
-			  detect_irq, IRQF_TRIGGER_FALLING,
-			  "MMC detect", data);
-	if (ret)
-		goto exit_free_wp;
-
-	return 0;
-
-exit_free_wp:
-	gpio_free(gpio_wp);
-
-exit_free_det:
-	gpio_free(gpio_det);
-
-	return ret;
-}
-
-static void mxc_mmc1_exit(struct device *dev, void *data)
-{
-	gpio_free(gpio_det);
-	gpio_free(gpio_wp);
-	free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)), data);
-}
-
-static const struct imxmmc_platform_data mmc_pdata __initconst = {
-	.get_ro	= mxc_mmc1_get_ro,
-	.init	= mxc_mmc1_init,
-	.exit	= mxc_mmc1_exit,
-};
-
-/* Framebuffer support */
-static const struct fb_videomode fb_modedb = {
-	/* 640x480 TFT panel (IPS-056T) */
-	.name		= "CRT-VGA",
-	.refresh	= 64,
-	.xres		= 640,
-	.yres		= 480,
-	.pixclock	= 30000,
-	.left_margin	= 200,
-	.right_margin	= 2,
-	.upper_margin	= 2,
-	.lower_margin	= 2,
-	.hsync_len	= 3,
-	.vsync_len	= 1,
-	.sync		= FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
-	.vmode		= FB_VMODE_NONINTERLACED,
-	.flag		= 0,
-};
-
-static struct mx3fb_platform_data fb_pdata __initdata = {
-	.name		= "CRT-VGA",
-	.mode		= &fb_modedb,
-	.num_modes	= 1,
-};
-
-#define LCD_VCC_EN_GPIO	 (7)
-
-static void __init mx31lilly_init_fb(void)
-{
-	if (gpio_request(LCD_VCC_EN_GPIO, "LCD enable") != 0) {
-		printk(KERN_WARNING "unable to request LCD_VCC_EN pin.\n");
-		return;
-	}
-
-	imx31_add_ipu_core();
-	imx31_add_mx3_sdc_fb(&fb_pdata);
-	gpio_direction_output(LCD_VCC_EN_GPIO, 1);
-}
-
-void __init mx31lilly_db_init(void)
-{
-	mxc_iomux_setup_multiple_pins(lilly_db_board_pins,
-					ARRAY_SIZE(lilly_db_board_pins),
-					"development board pins");
-	imx31_add_mxc_mmc(0, &mmc_pdata);
-	mx31lilly_init_fb();
-}
diff --git a/arch/arm/mach-imx/mx31lite-db.c b/arch/arm/mach-imx/mx31lite-db.c
deleted file mode 100644
index 13da7325c32b..000000000000
--- a/arch/arm/mach-imx/mx31lite-db.c
+++ /dev/null
@@ -1,154 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- *  LogicPD i.MX31 SOM-LV development board support
- *
- *    Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- *  based on code for other MX31 boards,
- *
- *    Copyright 2005-2007 Freescale Semiconductor
- *    Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- *    Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lite.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * This file contains board-specific initialization routines for the
- * LogicPD i.MX31 SOM-LV development board, aka 'LiteKit'.
- * If you design an own baseboard for the module, use this file as base
- * for support code.
- */
-
-static unsigned int litekit_db_board_pins[] __initdata = {
-	/* SDHC1 */
-	MX31_PIN_SD1_DATA0__SD1_DATA0,
-	MX31_PIN_SD1_DATA1__SD1_DATA1,
-	MX31_PIN_SD1_DATA2__SD1_DATA2,
-	MX31_PIN_SD1_DATA3__SD1_DATA3,
-	MX31_PIN_SD1_CLK__SD1_CLK,
-	MX31_PIN_SD1_CMD__SD1_CMD,
-};
-
-/* MMC */
-
-static int gpio_det, gpio_wp;
-
-#define MMC_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-		     PAD_CTL_ODE_CMOS)
-
-static int mxc_mmc1_get_ro(struct device *dev)
-{
-	return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_GPIO1_6));
-}
-
-static int mxc_mmc1_init(struct device *dev,
-			 irq_handler_t detect_irq, void *data)
-{
-	int ret;
-
-	gpio_det = IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1);
-	gpio_wp = IOMUX_TO_GPIO(MX31_PIN_GPIO1_6);
-
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA0,
-			  MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA1,
-			  MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA2,
-			  MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_SD1_DATA3,
-			  MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_SD1_CMD,
-			  MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
-	mxc_iomux_set_pad(MX31_PIN_SD1_CLK, MMC_PAD_CFG);
-
-	ret = gpio_request(gpio_det, "MMC detect");
-	if (ret)
-		return ret;
-
-	ret = gpio_request(gpio_wp, "MMC w/p");
-	if (ret)
-		goto exit_free_det;
-
-	gpio_direction_input(gpio_det);
-	gpio_direction_input(gpio_wp);
-
-	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)),
-			  detect_irq,
-			  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-			  "MMC detect", data);
-	if (ret)
-		goto exit_free_wp;
-
-	return 0;
-
-exit_free_wp:
-	gpio_free(gpio_wp);
-
-exit_free_det:
-	gpio_free(gpio_det);
-
-	return ret;
-}
-
-static void mxc_mmc1_exit(struct device *dev, void *data)
-{
-	gpio_free(gpio_det);
-	gpio_free(gpio_wp);
-	free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)), data);
-}
-
-static const struct imxmmc_platform_data mmc_pdata __initconst = {
-	.get_ro	 = mxc_mmc1_get_ro,
-	.init	   = mxc_mmc1_init,
-	.exit	   = mxc_mmc1_exit,
-};
-
-/* GPIO LEDs */
-
-static const struct gpio_led litekit_leds[] __initconst = {
-	{
-		.name           = "GPIO0",
-		.gpio           = IOMUX_TO_GPIO(MX31_PIN_COMPARE),
-		.active_low     = 1,
-		.default_state  = LEDS_GPIO_DEFSTATE_OFF,
-	},
-	{
-		.name           = "GPIO1",
-		.gpio           = IOMUX_TO_GPIO(MX31_PIN_CAPTURE),
-		.active_low     = 1,
-		.default_state  = LEDS_GPIO_DEFSTATE_OFF,
-	}
-};
-
-static const struct gpio_led_platform_data
-		litekit_led_platform_data __initconst = {
-	.leds           = litekit_leds,
-	.num_leds       = ARRAY_SIZE(litekit_leds),
-};
-
-void __init mx31lite_db_init(void)
-{
-	mxc_iomux_setup_multiple_pins(litekit_db_board_pins,
-					ARRAY_SIZE(litekit_db_board_pins),
-					"development board pins");
-	imx31_add_mxc_mmc(0, &mmc_pdata);
-	gpio_led_register_device(-1, &litekit_led_platform_data);
-	imx31_add_imx2_wdt();
-	imx31_add_mxc_rtc();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-devboard.c b/arch/arm/mach-imx/mx31moboard-devboard.c
deleted file mode 100644
index 6a9db0663a80..000000000000
--- a/arch/arm/mach-imx/mx31moboard-devboard.c
+++ /dev/null
@@ -1,238 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int devboard_pins[] = {
-	/* UART1 */
-	MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2,
-	MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2,
-	/* SDHC2 */
-	MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2,
-	MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0,
-	MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD,
-	MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29,
-	/* USB H1 */
-	MX31_PIN_CSPI1_MISO__USBH1_RXDP, MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
-	MX31_PIN_CSPI1_SS0__USBH1_TXDM, MX31_PIN_CSPI1_SS1__USBH1_TXDP,
-	MX31_PIN_CSPI1_SS2__USBH1_RCV, MX31_PIN_CSPI1_SCLK__USBH1_OEB,
-	MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, MX31_PIN_SFS6__USBH1_SUSPEND,
-	MX31_PIN_NFRE_B__GPIO1_11, MX31_PIN_NFALE__GPIO1_12,
-	/* SEL */
-	MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
-	MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR)
-#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW)
-
-static int devboard_sdhc2_get_ro(struct device *dev)
-{
-	return !gpio_get_value(SDHC2_WP);
-}
-
-static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
-		void *data)
-{
-	int ret;
-
-	ret = gpio_request(SDHC2_CD, "sdhc-detect");
-	if (ret)
-		return ret;
-
-	gpio_direction_input(SDHC2_CD);
-
-	ret = gpio_request(SDHC2_WP, "sdhc-wp");
-	if (ret)
-		goto err_gpio_free;
-	gpio_direction_input(SDHC2_WP);
-
-	ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq,
-		IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-		"sdhc2-card-detect", data);
-	if (ret)
-		goto err_gpio_free_2;
-
-	return 0;
-
-err_gpio_free_2:
-	gpio_free(SDHC2_WP);
-err_gpio_free:
-	gpio_free(SDHC2_CD);
-
-	return ret;
-}
-
-static void devboard_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(SDHC2_CD), data);
-	gpio_free(SDHC2_WP);
-	gpio_free(SDHC2_CD);
-}
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
-	.get_ro	= devboard_sdhc2_get_ro,
-	.init	= devboard_sdhc2_init,
-	.exit	= devboard_sdhc2_exit,
-};
-
-#define SEL0 IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define SEL1 IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define SEL2 IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define SEL3 IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void devboard_init_sel_gpios(void)
-{
-	if (!gpio_request(SEL0, "sel0")) {
-		gpio_direction_input(SEL0);
-		gpio_export(SEL0, true);
-	}
-
-	if (!gpio_request(SEL1, "sel1")) {
-		gpio_direction_input(SEL1);
-		gpio_export(SEL1, true);
-	}
-
-	if (!gpio_request(SEL2, "sel2")) {
-		gpio_direction_input(SEL2);
-		gpio_export(SEL2, true);
-	}
-
-	if (!gpio_request(SEL3, "sel3")) {
-		gpio_direction_input(SEL3);
-		gpio_export(SEL3, true);
-	}
-}
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int devboard_usbh1_hw_init(struct platform_device *pdev)
-{
-	mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SFS6, USB_PAD_CFG);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-#define USBH1_VBUSEN_B	IOMUX_TO_GPIO(MX31_PIN_NFRE_B)
-#define USBH1_MODE	IOMUX_TO_GPIO(MX31_PIN_NFALE)
-
-static int devboard_isp1105_init(struct usb_phy *otg)
-{
-	int ret = gpio_request(USBH1_MODE, "usbh1-mode");
-	if (ret)
-		return ret;
-	/* single ended */
-	gpio_direction_output(USBH1_MODE, 0);
-
-	ret = gpio_request(USBH1_VBUSEN_B, "usbh1-vbusen");
-	if (ret) {
-		gpio_free(USBH1_MODE);
-		return ret;
-	}
-	gpio_direction_output(USBH1_VBUSEN_B, 1);
-
-	return 0;
-}
-
-
-static int devboard_isp1105_set_vbus(struct usb_otg *otg, bool on)
-{
-	if (on)
-		gpio_set_value(USBH1_VBUSEN_B, 0);
-	else
-		gpio_set_value(USBH1_VBUSEN_B, 1);
-
-	return 0;
-}
-
-static struct mxc_usbh_platform_data usbh1_pdata __initdata = {
-	.init	= devboard_usbh1_hw_init,
-	.portsc	= MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static int __init devboard_usbh1_init(void)
-{
-	struct usb_phy *phy;
-	struct platform_device *pdev;
-
-	phy = kzalloc(sizeof(*phy), GFP_KERNEL);
-	if (!phy)
-		return -ENOMEM;
-
-	phy->otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
-	if (!phy->otg) {
-		kfree(phy);
-		return -ENOMEM;
-	}
-
-	phy->label	= "ISP1105";
-	phy->init	= devboard_isp1105_init;
-	phy->otg->set_vbus	= devboard_isp1105_set_vbus;
-
-	usbh1_pdata.otg = phy;
-
-	pdev = imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
-	return PTR_ERR_OR_ZERO(pdev);
-}
-
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_ULPI,
-};
-
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_devboard_init(void)
-{
-	printk(KERN_INFO "Initializing mx31devboard peripherals\n");
-
-	mxc_iomux_setup_multiple_pins(devboard_pins, ARRAY_SIZE(devboard_pins),
-		"devboard");
-
-	imx31_add_imx_uart1(&uart_pdata);
-
-	imx31_add_mxc_mmc(1, &sdhc2_pdata);
-
-	devboard_init_sel_gpios();
-
-	imx31_add_fsl_usb2_udc(&usb_pdata);
-
-	devboard_usbh1_init();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-marxbot.c b/arch/arm/mach-imx/mx31moboard-marxbot.c
deleted file mode 100644
index c2690008e6fc..000000000000
--- a/arch/arm/mach-imx/mx31moboard-marxbot.c
+++ /dev/null
@@ -1,270 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/spi/spi.h>
-#include <linux/slab.h>
-#include <linux/platform_device.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int marxbot_pins[] = {
-	/* SDHC2 */
-	MX31_PIN_PC_PWRON__SD2_DATA3, MX31_PIN_PC_VS1__SD2_DATA2,
-	MX31_PIN_PC_READY__SD2_DATA1, MX31_PIN_PC_WAIT_B__SD2_DATA0,
-	MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD,
-	MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29,
-	/* dsPIC resets */
-	MX31_PIN_STXD5__GPIO1_21, MX31_PIN_SRXD5__GPIO1_22,
-	/*battery detection */
-	MX31_PIN_LCS0__GPIO3_23,
-	/* USB H1 */
-	MX31_PIN_CSPI1_MISO__USBH1_RXDP, MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
-	MX31_PIN_CSPI1_SS0__USBH1_TXDM, MX31_PIN_CSPI1_SS1__USBH1_TXDP,
-	MX31_PIN_CSPI1_SS2__USBH1_RCV, MX31_PIN_CSPI1_SCLK__USBH1_OEB,
-	MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, MX31_PIN_SFS6__USBH1_SUSPEND,
-	MX31_PIN_NFRE_B__GPIO1_11, MX31_PIN_NFALE__GPIO1_12,
-	/* SEL */
-	MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
-	MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR)
-#define SDHC2_WP IOMUX_TO_GPIO(MX31_PIN_ATA_DIOW)
-
-static int marxbot_sdhc2_get_ro(struct device *dev)
-{
-	return !gpio_get_value(SDHC2_WP);
-}
-
-static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
-		void *data)
-{
-	int ret;
-
-	ret = gpio_request(SDHC2_CD, "sdhc-detect");
-	if (ret)
-		return ret;
-
-	gpio_direction_input(SDHC2_CD);
-
-	ret = gpio_request(SDHC2_WP, "sdhc-wp");
-	if (ret)
-		goto err_gpio_free;
-	gpio_direction_input(SDHC2_WP);
-
-	ret = request_irq(gpio_to_irq(SDHC2_CD), detect_irq,
-		IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-		"sdhc2-card-detect", data);
-	if (ret)
-		goto err_gpio_free_2;
-
-	return 0;
-
-err_gpio_free_2:
-	gpio_free(SDHC2_WP);
-err_gpio_free:
-	gpio_free(SDHC2_CD);
-
-	return ret;
-}
-
-static void marxbot_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(SDHC2_CD), data);
-	gpio_free(SDHC2_WP);
-	gpio_free(SDHC2_CD);
-}
-
-static const struct imxmmc_platform_data sdhc2_pdata __initconst = {
-	.get_ro	= marxbot_sdhc2_get_ro,
-	.init	= marxbot_sdhc2_init,
-	.exit	= marxbot_sdhc2_exit,
-};
-
-#define TRSLAT_RST_B	IOMUX_TO_GPIO(MX31_PIN_STXD5)
-#define DSPICS_RST_B	IOMUX_TO_GPIO(MX31_PIN_SRXD5)
-
-static void dspics_resets_init(void)
-{
-	if (!gpio_request(TRSLAT_RST_B, "translator-rst")) {
-		gpio_direction_output(TRSLAT_RST_B, 0);
-		gpio_export(TRSLAT_RST_B, false);
-	}
-
-	if (!gpio_request(DSPICS_RST_B, "dspics-rst")) {
-		gpio_direction_output(DSPICS_RST_B, 0);
-		gpio_export(DSPICS_RST_B, false);
-	}
-}
-
-static struct spi_board_info marxbot_spi_board_info[] __initdata = {
-	{
-		.modalias = "spidev",
-		.max_speed_hz = 300000,
-		.bus_num = 1,
-		.chip_select = 1, /* according spi1_cs[] ! */
-	},
-};
-
-#define SEL0 IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define SEL1 IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define SEL2 IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define SEL3 IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void marxbot_init_sel_gpios(void)
-{
-	if (!gpio_request(SEL0, "sel0")) {
-		gpio_direction_input(SEL0);
-		gpio_export(SEL0, true);
-	}
-
-	if (!gpio_request(SEL1, "sel1")) {
-		gpio_direction_input(SEL1);
-		gpio_export(SEL1, true);
-	}
-
-	if (!gpio_request(SEL2, "sel2")) {
-		gpio_direction_input(SEL2);
-		gpio_export(SEL2, true);
-	}
-
-	if (!gpio_request(SEL3, "sel3")) {
-		gpio_direction_input(SEL3);
-		gpio_export(SEL3, true);
-	}
-}
-
-#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
-			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
-static int marxbot_usbh1_hw_init(struct platform_device *pdev)
-{
-	mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
-
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
-	mxc_iomux_set_pad(MX31_PIN_SFS6, USB_PAD_CFG);
-
-	mdelay(10);
-
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_SINGLE_UNI);
-}
-
-#define USBH1_VBUSEN_B	IOMUX_TO_GPIO(MX31_PIN_NFRE_B)
-#define USBH1_MODE	IOMUX_TO_GPIO(MX31_PIN_NFALE)
-
-static int marxbot_isp1105_init(struct usb_phy *otg)
-{
-	int ret = gpio_request(USBH1_MODE, "usbh1-mode");
-	if (ret)
-		return ret;
-	/* single ended */
-	gpio_direction_output(USBH1_MODE, 0);
-
-	ret = gpio_request(USBH1_VBUSEN_B, "usbh1-vbusen");
-	if (ret) {
-		gpio_free(USBH1_MODE);
-		return ret;
-	}
-	gpio_direction_output(USBH1_VBUSEN_B, 1);
-
-	return 0;
-}
-
-
-static int marxbot_isp1105_set_vbus(struct usb_otg *otg, bool on)
-{
-	if (on)
-		gpio_set_value(USBH1_VBUSEN_B, 0);
-	else
-		gpio_set_value(USBH1_VBUSEN_B, 1);
-
-	return 0;
-}
-
-static struct mxc_usbh_platform_data usbh1_pdata __initdata = {
-	.init	= marxbot_usbh1_hw_init,
-	.portsc	= MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
-};
-
-static int __init marxbot_usbh1_init(void)
-{
-	struct usb_phy *phy;
-	struct platform_device *pdev;
-
-	phy = kzalloc(sizeof(*phy), GFP_KERNEL);
-	if (!phy)
-		return -ENOMEM;
-
-	phy->otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
-	if (!phy->otg) {
-		kfree(phy);
-		return -ENOMEM;
-	}
-
-	phy->label	= "ISP1105";
-	phy->init	= marxbot_isp1105_init;
-	phy->otg->set_vbus	= marxbot_isp1105_set_vbus;
-
-	usbh1_pdata.otg = phy;
-
-	pdev = imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
-
-	return PTR_ERR_OR_ZERO(pdev);
-}
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_ULPI,
-};
-
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_marxbot_init(void)
-{
-	printk(KERN_INFO "Initializing mx31marxbot peripherals\n");
-
-	mxc_iomux_setup_multiple_pins(marxbot_pins, ARRAY_SIZE(marxbot_pins),
-		"marxbot");
-
-	marxbot_init_sel_gpios();
-
-	dspics_resets_init();
-
-	imx31_add_mxc_mmc(1, &sdhc2_pdata);
-
-	spi_register_board_info(marxbot_spi_board_info,
-		ARRAY_SIZE(marxbot_spi_board_info));
-
-	/* battery present pin */
-	gpio_request(IOMUX_TO_GPIO(MX31_PIN_LCS0), "bat-present");
-	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_LCS0));
-	gpio_export(IOMUX_TO_GPIO(MX31_PIN_LCS0), false);
-
-	imx31_add_fsl_usb2_udc(&usb_pdata);
-
-	marxbot_usbh1_init();
-}
diff --git a/arch/arm/mach-imx/mx31moboard-smartbot.c b/arch/arm/mach-imx/mx31moboard-smartbot.c
deleted file mode 100644
index d165bd952bad..000000000000
--- a/arch/arm/mach-imx/mx31moboard-smartbot.c
+++ /dev/null
@@ -1,124 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/platform_device.h>
-#include <linux/types.h>
-
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include "board-mx31moboard.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-#include "ulpi.h"
-
-static unsigned int smartbot_pins[] = {
-	/* UART1 */
-	MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2,
-	MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2,
-	/* ENABLES */
-	MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
-	MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
-	.operating_mode	= FSL_USB2_DR_DEVICE,
-	.phy_mode	= FSL_USB2_PHY_ULPI,
-};
-
-#if defined(CONFIG_USB_ULPI)
-
-static int smartbot_otg_init(struct platform_device *pdev)
-{
-	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
-}
-
-static struct mxc_usbh_platform_data otg_host_pdata __initdata = {
-	.init	= smartbot_otg_init,
-	.portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
-};
-
-static int __init smartbot_otg_host_init(void)
-{
-	struct platform_device *pdev;
-
-	otg_host_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-		ULPI_OTG_DRVVBUS_EXT);
-	if (!otg_host_pdata.otg)
-		return -ENODEV;
-
-	pdev = imx31_add_mxc_ehci_otg(&otg_host_pdata);
-
-	return PTR_ERR_OR_ZERO(pdev);
-}
-#else
-static inline int smartbot_otg_host_init(void) { return 0; }
-#endif
-
-#define POWER_EN IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1)
-#define DSPIC_RST_B IOMUX_TO_GPIO(MX31_PIN_DSR_DCE1)
-#define TRSLAT_RST_B IOMUX_TO_GPIO(MX31_PIN_RI_DCE1)
-#define TRSLAT_SRC_CHOICE IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)
-
-static void smartbot_resets_init(void)
-{
-	if (!gpio_request(POWER_EN, "power-enable")) {
-		gpio_direction_output(POWER_EN, 0);
-		gpio_export(POWER_EN, false);
-	}
-
-	if (!gpio_request(DSPIC_RST_B, "dspic-rst")) {
-		gpio_direction_output(DSPIC_RST_B, 0);
-		gpio_export(DSPIC_RST_B, false);
-	}
-
-	if (!gpio_request(TRSLAT_RST_B, "translator-rst")) {
-		gpio_direction_output(TRSLAT_RST_B, 0);
-		gpio_export(TRSLAT_RST_B, false);
-	}
-
-	if (!gpio_request(TRSLAT_SRC_CHOICE, "translator-src-choice")) {
-		gpio_direction_output(TRSLAT_SRC_CHOICE, 0);
-		gpio_export(TRSLAT_SRC_CHOICE, false);
-	}
-}
-/*
- * system init for baseboard usage. Will be called by mx31moboard init.
- */
-void __init mx31moboard_smartbot_init(int board)
-{
-	printk(KERN_INFO "Initializing mx31smartbot peripherals\n");
-
-	mxc_iomux_setup_multiple_pins(smartbot_pins, ARRAY_SIZE(smartbot_pins),
-		"smartbot");
-
-	imx31_add_imx_uart1(&uart_pdata);
-
-	switch (board) {
-	case MX31SMARTBOT:
-		imx31_add_fsl_usb2_udc(&usb_pdata);
-		break;
-	case MX31EYEBOT:
-		smartbot_otg_host_init();
-		break;
-	default:
-		printk(KERN_WARNING "Unknown board %d, USB OTG not initialized",
-			board);
-	}
-
-	smartbot_resets_init();
-}
diff --git a/arch/arm/mach-imx/mx35.h b/arch/arm/mach-imx/mx35.h
index 760de6a0af7e..5a8a87a85c14 100644
--- a/arch/arm/mach-imx/mx35.h
+++ b/arch/arm/mach-imx/mx35.h
@@ -2,190 +2,17 @@
 #ifndef __MACH_MX35_H__
 #define __MACH_MX35_H__
 
-/*
- * IRAM
- */
-#define MX35_IRAM_BASE_ADDR		0x10000000	/* internal ram */
-#define MX35_IRAM_SIZE			SZ_128K
-
-#define MX35_L2CC_BASE_ADDR		0x30000000
-#define MX35_L2CC_SIZE			SZ_1M
-
 #define MX35_AIPS1_BASE_ADDR		0x43f00000
 #define MX35_AIPS1_SIZE			SZ_1M
-#define MX35_MAX_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x04000)
-#define MX35_EVTMON_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x08000)
-#define MX35_CLKCTL_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x0c000)
-#define MX35_ETB_SLOT4_BASE_ADDR		(MX35_AIPS1_BASE_ADDR + 0x10000)
-#define MX35_ETB_SLOT5_BASE_ADDR		(MX35_AIPS1_BASE_ADDR + 0x14000)
-#define MX35_ECT_CTIO_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x18000)
-#define MX35_I2C1_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x80000)
-#define MX35_I2C3_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x84000)
-#define MX35_UART1_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x90000)
-#define MX35_UART2_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x94000)
-#define MX35_I2C2_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x98000)
-#define MX35_OWIRE_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0x9c000)
-#define MX35_SSI1_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xa0000)
-#define MX35_CSPI1_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xa4000)
-#define MX35_KPP_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xa8000)
-#define MX35_IOMUXC_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xac000)
-#define MX35_ECT_IP1_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xb8000)
-#define MX35_ECT_IP2_BASE_ADDR			(MX35_AIPS1_BASE_ADDR + 0xbc000)
-
 #define MX35_SPBA0_BASE_ADDR		0x50000000
 #define MX35_SPBA0_SIZE			SZ_1M
-#define MX35_UART3_BASE_ADDR			(MX35_SPBA0_BASE_ADDR + 0x0c000)
-#define MX35_CSPI2_BASE_ADDR			(MX35_SPBA0_BASE_ADDR + 0x10000)
-#define MX35_SSI2_BASE_ADDR			(MX35_SPBA0_BASE_ADDR + 0x14000)
-#define MX35_ATA_BASE_ADDR			(MX35_SPBA0_BASE_ADDR + 0x20000)
-#define MX35_MSHC1_BASE_ADDR			(MX35_SPBA0_BASE_ADDR + 0x24000)
-#define MX35_FEC_BASE_ADDR		0x50038000
-#define MX35_SPBA_CTRL_BASE_ADDR		(MX35_SPBA0_BASE_ADDR + 0x3c000)
-
 #define MX35_AIPS2_BASE_ADDR		0x53f00000
 #define MX35_AIPS2_SIZE			SZ_1M
-#define MX35_CCM_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0x80000)
-#define MX35_GPT1_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0x90000)
-#define MX35_EPIT1_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0x94000)
-#define MX35_EPIT2_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0x98000)
-#define MX35_GPIO3_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xa4000)
-#define MX35_SCC_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xac000)
-#define MX35_RNGA_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xb0000)
-#define MX35_ESDHC1_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xb4000)
-#define MX35_ESDHC2_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xb8000)
-#define MX35_ESDHC3_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xbc000)
-#define MX35_IPU_CTRL_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xc0000)
-#define MX35_AUDMUX_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xc4000)
-#define MX35_GPIO1_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xcc000)
-#define MX35_GPIO2_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xd0000)
-#define MX35_SDMA_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xd4000)
-#define MX35_RTC_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xd8000)
-#define MX35_WDOG_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xdc000)
-#define MX35_PWM_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xe0000)
-#define MX35_CAN1_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xe4000)
-#define MX35_CAN2_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xe8000)
-#define MX35_RTIC_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xec000)
-#define MX35_IIM_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xf0000)
-#define MX35_USB_BASE_ADDR			(MX35_AIPS2_BASE_ADDR + 0xf4000)
-#define MX35_USB_OTG_BASE_ADDR			(MX35_USB_BASE_ADDR + 0x0000)
-/*
- * The Reference Manual (IMX35RM, Rev. 2, 3/2009) claims an offset of 0x200 for
- * HS.  When host support was implemented only a preliminary document was
- * available, which told 0x400.  This works fine.
- */
-#define MX35_USB_HS_BASE_ADDR			(MX35_USB_BASE_ADDR + 0x0400)
-
-#define MX35_ROMP_BASE_ADDR		0x60000000
-#define MX35_ROMP_SIZE			SZ_1M
-
 #define MX35_AVIC_BASE_ADDR		0x68000000
 #define MX35_AVIC_SIZE			SZ_1M
-
-/*
- * Memory regions and CS
- */
-#define MX35_IPU_MEM_BASE_ADDR		0x70000000
-#define MX35_CSD0_BASE_ADDR		0x80000000
-#define MX35_CSD1_BASE_ADDR		0x90000000
-
-#define MX35_CS0_BASE_ADDR		0xa0000000
-#define MX35_CS1_BASE_ADDR		0xa8000000
-#define MX35_CS2_BASE_ADDR		0xb0000000
-#define MX35_CS3_BASE_ADDR		0xb2000000
-
-#define MX35_CS4_BASE_ADDR		0xb4000000
-#define MX35_CS4_BASE_ADDR_VIRT		0xf6000000
-#define MX35_CS4_SIZE			SZ_32M
-
-#define MX35_CS5_BASE_ADDR		0xb6000000
-#define MX35_CS5_BASE_ADDR_VIRT		0xf8000000
-#define MX35_CS5_SIZE			SZ_32M
-
-/*
- * NAND, SDRAM, WEIM, M3IF, EMI controllers
- */
 #define MX35_X_MEMC_BASE_ADDR		0xb8000000
 #define MX35_X_MEMC_SIZE		SZ_64K
-#define MX35_ESDCTL_BASE_ADDR			(MX35_X_MEMC_BASE_ADDR + 0x1000)
-#define MX35_WEIM_BASE_ADDR			(MX35_X_MEMC_BASE_ADDR + 0x2000)
-#define MX35_M3IF_BASE_ADDR			(MX35_X_MEMC_BASE_ADDR + 0x3000)
-#define MX35_EMI_CTL_BASE_ADDR			(MX35_X_MEMC_BASE_ADDR + 0x4000)
-#define MX35_PCMCIA_CTL_BASE_ADDR		MX35_EMI_CTL_BASE_ADDR
-
-#define MX35_NFC_BASE_ADDR		0xbb000000
-#define MX35_PCMCIA_MEM_BASE_ADDR	0xbc000000
 
 #define MX35_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX35_IO_ADDRESS(x)		IOMEM(MX35_IO_P2V(x))
-
-/*
- * Interrupt numbers
- */
-#include <asm/irq.h>
-#define MX35_INT_OWIRE		(NR_IRQS_LEGACY + 2)
-#define MX35_INT_I2C3		(NR_IRQS_LEGACY + 3)
-#define MX35_INT_I2C2		(NR_IRQS_LEGACY + 4)
-#define MX35_INT_RTIC		(NR_IRQS_LEGACY + 6)
-#define MX35_INT_ESDHC1		(NR_IRQS_LEGACY + 7)
-#define MX35_INT_ESDHC2		(NR_IRQS_LEGACY + 8)
-#define MX35_INT_ESDHC3		(NR_IRQS_LEGACY + 9)
-#define MX35_INT_I2C1		(NR_IRQS_LEGACY + 10)
-#define MX35_INT_SSI1		(NR_IRQS_LEGACY + 11)
-#define MX35_INT_SSI2		(NR_IRQS_LEGACY + 12)
-#define MX35_INT_CSPI2		(NR_IRQS_LEGACY + 13)
-#define MX35_INT_CSPI1		(NR_IRQS_LEGACY + 14)
-#define MX35_INT_ATA		(NR_IRQS_LEGACY + 15)
-#define MX35_INT_GPU2D		(NR_IRQS_LEGACY + 16)
-#define MX35_INT_ASRC		(NR_IRQS_LEGACY + 17)
-#define MX35_INT_UART3		(NR_IRQS_LEGACY + 18)
-#define MX35_INT_IIM		(NR_IRQS_LEGACY + 19)
-#define MX35_INT_RNGA		(NR_IRQS_LEGACY + 22)
-#define MX35_INT_EVTMON		(NR_IRQS_LEGACY + 23)
-#define MX35_INT_KPP		(NR_IRQS_LEGACY + 24)
-#define MX35_INT_RTC		(NR_IRQS_LEGACY + 25)
-#define MX35_INT_PWM		(NR_IRQS_LEGACY + 26)
-#define MX35_INT_EPIT2		(NR_IRQS_LEGACY + 27)
-#define MX35_INT_EPIT1		(NR_IRQS_LEGACY + 28)
-#define MX35_INT_GPT		(NR_IRQS_LEGACY + 29)
-#define MX35_INT_POWER_FAIL	(NR_IRQS_LEGACY + 30)
-#define MX35_INT_UART2		(NR_IRQS_LEGACY + 32)
-#define MX35_INT_NFC		(NR_IRQS_LEGACY + 33)
-#define MX35_INT_SDMA		(NR_IRQS_LEGACY + 34)
-#define MX35_INT_USB_HS		(NR_IRQS_LEGACY + 35)
-#define MX35_INT_USB_OTG	(NR_IRQS_LEGACY + 37)
-#define MX35_INT_MSHC1		(NR_IRQS_LEGACY + 39)
-#define MX35_INT_ESAI		(NR_IRQS_LEGACY + 40)
-#define MX35_INT_IPU_ERR	(NR_IRQS_LEGACY + 41)
-#define MX35_INT_IPU_SYN	(NR_IRQS_LEGACY + 42)
-#define MX35_INT_CAN1		(NR_IRQS_LEGACY + 43)
-#define MX35_INT_CAN2		(NR_IRQS_LEGACY + 44)
-#define MX35_INT_UART1		(NR_IRQS_LEGACY + 45)
-#define MX35_INT_MLB		(NR_IRQS_LEGACY + 46)
-#define MX35_INT_SPDIF		(NR_IRQS_LEGACY + 47)
-#define MX35_INT_ECT		(NR_IRQS_LEGACY + 48)
-#define MX35_INT_SCC_SCM	(NR_IRQS_LEGACY + 49)
-#define MX35_INT_SCC_SMN	(NR_IRQS_LEGACY + 50)
-#define MX35_INT_GPIO2		(NR_IRQS_LEGACY + 51)
-#define MX35_INT_GPIO1		(NR_IRQS_LEGACY + 52)
-#define MX35_INT_WDOG		(NR_IRQS_LEGACY + 55)
-#define MX35_INT_GPIO3		(NR_IRQS_LEGACY + 56)
-#define MX35_INT_FEC		(NR_IRQS_LEGACY + 57)
-#define MX35_INT_EXT_POWER	(NR_IRQS_LEGACY + 58)
-#define MX35_INT_EXT_TEMPER	(NR_IRQS_LEGACY + 59)
-#define MX35_INT_EXT_SENSOR60	(NR_IRQS_LEGACY + 60)
-#define MX35_INT_EXT_SENSOR61	(NR_IRQS_LEGACY + 61)
-#define MX35_INT_EXT_WDOG	(NR_IRQS_LEGACY + 62)
-#define MX35_INT_EXT_TV		(NR_IRQS_LEGACY + 63)
-
-#define MX35_DMA_REQ_SSI2_RX1   22
-#define MX35_DMA_REQ_SSI2_TX1   23
-#define MX35_DMA_REQ_SSI2_RX0   24
-#define MX35_DMA_REQ_SSI2_TX0   25
-#define MX35_DMA_REQ_SSI1_RX1   26
-#define MX35_DMA_REQ_SSI1_TX1   27
-#define MX35_DMA_REQ_SSI1_RX0   28
-#define MX35_DMA_REQ_SSI1_TX0   29
-
-#define MX35_PROD_SIGNATURE		0x1	/* For MX31 */
 
 #endif /* ifndef __MACH_MX35_H__ */
diff --git a/arch/arm/mach-imx/pcm037.h b/arch/arm/mach-imx/pcm037.h
deleted file mode 100644
index 470d3c887e14..000000000000
--- a/arch/arm/mach-imx/pcm037.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __PCM037_H__
-#define __PCM037_H__
-
-enum pcm037_board_variant {
-	PCM037_PCM970,
-	PCM037_EET,
-};
-
-extern enum pcm037_board_variant pcm037_variant(void);
-
-#ifdef CONFIG_MACH_PCM037_EET
-int pcm037_eet_init_devices(void);
-#else
-static inline int pcm037_eet_init_devices(void) { return 0; }
-#endif
-
-#endif
diff --git a/arch/arm/mach-imx/pm-imx27.c b/arch/arm/mach-imx/pm-imx27.c
index d943535566c8..020e6deb67c8 100644
--- a/arch/arm/mach-imx/pm-imx27.c
+++ b/arch/arm/mach-imx/pm-imx27.c
@@ -7,6 +7,7 @@
  * modify it under the terms of the GNU General Public License.
  */
 
+#include <linux/of_address.h>
 #include <linux/kernel.h>
 #include <linux/suspend.h>
 #include <linux/io.h>
@@ -15,13 +16,20 @@
 
 static int mx27_suspend_enter(suspend_state_t state)
 {
+	void __iomem *ccm_base;
+	struct device_node *np;
 	u32 cscr;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
+	ccm_base = of_iomap(np, 0);
+	BUG_ON(!ccm_base);
+
 	switch (state) {
 	case PM_SUSPEND_MEM:
 		/* Clear MPEN and SPEN to disable MPLL/SPLL */
-		cscr = imx_readl(MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+		cscr = imx_readl(ccm_base);
 		cscr &= 0xFFFFFFFC;
-		imx_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+		imx_writel(cscr, ccm_base);
 		/* Executes WFI */
 		cpu_do_idle();
 		break;
diff --git a/arch/arm/mach-imx/ulpi.h b/arch/arm/mach-imx/ulpi.h
deleted file mode 100644
index b367902c9c32..000000000000
--- a/arch/arm/mach-imx/ulpi.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __MACH_ULPI_H
-#define __MACH_ULPI_H
-
-#include <linux/usb/ulpi.h>
-
-#ifdef CONFIG_USB_ULPI_VIEWPORT
-static inline struct usb_phy *imx_otg_ulpi_create(unsigned int flags)
-{
-	return otg_ulpi_create(&ulpi_viewport_access_ops, flags);
-}
-#else
-static inline struct usb_phy *imx_otg_ulpi_create(unsigned int flags)
-{
-	return NULL;
-}
-#endif
-
-#endif /* __MACH_ULPI_H */
-
diff --git a/arch/arm/mach-mstar/Kconfig b/arch/arm/mach-mstar/Kconfig
index 52744fe32368..576d1ab293c8 100644
--- a/arch/arm/mach-mstar/Kconfig
+++ b/arch/arm/mach-mstar/Kconfig
@@ -3,6 +3,7 @@ menuconfig ARCH_MSTARV7
 	depends on ARCH_MULTI_V7
 	select ARM_GIC
 	select ARM_HEAVY_MB
+	select MST_IRQ
 	help
 	  Support for newer MStar/Sigmastar SoC families that are
 	  based on Armv7 cores like the Cortex A7 and share the same
diff --git a/arch/arm/mach-omap1/include/mach/mux.h b/arch/arm/mach-omap1/include/mach/mux.h
index adfe1f6bd0c5..3f6dc55d9898 100644
--- a/arch/arm/mach-omap1/include/mach/mux.h
+++ b/arch/arm/mach-omap1/include/mach/mux.h
@@ -88,7 +88,7 @@
  * OMAP730/850 has a slightly different config for the pin mux.
  * - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
  *   not the FUNC_MUX_CTRL_x regs from hardware.h
- * - for pull-up/down, only has one enable bit which is is in the same register
+ * - for pull-up/down, only has one enable bit which is in the same register
  *   as mux config
  */
 #define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode,	\
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index ea23205bf70f..3ee7bdff86b2 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -7,6 +7,7 @@ config ARCH_OMAP2
 	depends on ARCH_MULTI_V6
 	select ARCH_OMAP2PLUS
 	select CPU_V6
+	select PM_GENERIC_DOMAINS if PM
 	select SOC_HAS_OMAP2_SDRC
 
 config ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/am33xx.h b/arch/arm/mach-omap2/am33xx.h
index 5eef093e6738..bf2b5f87e404 100644
--- a/arch/arm/mach-omap2/am33xx.h
+++ b/arch/arm/mach-omap2/am33xx.h
@@ -1,7 +1,7 @@
 /*
  * This file contains the address info for various AM33XX modules.
  *
- * Copyright (C) 2011 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments, Inc. - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 334923d7652d..7290f033fd2d 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -3,7 +3,7 @@
  * Copyright (C) 2005 Nokia Corporation
  * Author: Paul Mundt <paul.mundt@nokia.com>
  *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  *
  * Modified from the original mach-omap/omap2/board-generic.c did by Paul
  * to support the OMAP2+ device tree boards with an unique board file.
diff --git a/arch/arm/mach-omap2/clockdomains33xx_data.c b/arch/arm/mach-omap2/clockdomains33xx_data.c
index 32c90fd9eba2..b4d5144df445 100644
--- a/arch/arm/mach-omap2/clockdomains33xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains33xx_data.c
@@ -1,7 +1,7 @@
 /*
  * AM33XX Clock Domain data.
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
  * This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/clockdomains81xx_data.c b/arch/arm/mach-omap2/clockdomains81xx_data.c
index 65fbd136b20c..127dc7ace71f 100644
--- a/arch/arm/mach-omap2/clockdomains81xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains81xx_data.c
@@ -1,7 +1,7 @@
 /*
  * TI81XX Clock Domain data.
  *
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
  *
  * This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/cm-regbits-33xx.h b/arch/arm/mach-omap2/cm-regbits-33xx.h
index c0823fd6d5e0..e7ae2bb515e3 100644
--- a/arch/arm/mach-omap2/cm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-33xx.h
@@ -4,7 +4,7 @@
  * This file is automatically generated from the AM33XX hardware databases.
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/cm-regbits-54xx.h b/arch/arm/mach-omap2/cm-regbits-54xx.h
index 44663b575bf4..fc886883866f 100644
--- a/arch/arm/mach-omap2/cm-regbits-54xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54xx Clock Management register bits
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley (paul@pwsan.com)
  * Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm-regbits-7xx.h b/arch/arm/mach-omap2/cm-regbits-7xx.h
index a78ccbaab1a6..2725af4d1f87 100644
--- a/arch/arm/mach-omap2/cm-regbits-7xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-7xx.h
@@ -2,7 +2,7 @@
 /*
  * DRA7xx Clock Management register bits
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Generated by code originally written by:
  * Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm1_54xx.h b/arch/arm/mach-omap2/cm1_54xx.h
index 7be363a27a40..eb86bbd93f35 100644
--- a/arch/arm/mach-omap2/cm1_54xx.h
+++ b/arch/arm/mach-omap2/cm1_54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54xx CM1 instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley (paul@pwsan.com)
  * Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm1_7xx.h b/arch/arm/mach-omap2/cm1_7xx.h
index 28660edc7f5f..aae3831f5233 100644
--- a/arch/arm/mach-omap2/cm1_7xx.h
+++ b/arch/arm/mach-omap2/cm1_7xx.h
@@ -2,7 +2,7 @@
 /*
  * DRA7xx CM1 instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Generated by code originally written by:
  * Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm2_54xx.h b/arch/arm/mach-omap2/cm2_54xx.h
index c5da1f5cae93..8e49765cd441 100644
--- a/arch/arm/mach-omap2/cm2_54xx.h
+++ b/arch/arm/mach-omap2/cm2_54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54xx CM2 instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley (paul@pwsan.com)
  * Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/cm2_7xx.h b/arch/arm/mach-omap2/cm2_7xx.h
index e16fc58ef152..f8734605b1e1 100644
--- a/arch/arm/mach-omap2/cm2_7xx.h
+++ b/arch/arm/mach-omap2/cm2_7xx.h
@@ -2,7 +2,7 @@
 /*
  * DRA7xx CM2 instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Generated by code originally written by:
  * Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/cm33xx.c b/arch/arm/mach-omap2/cm33xx.c
index 084d454f6074..ac4882ebdca3 100644
--- a/arch/arm/mach-omap2/cm33xx.c
+++ b/arch/arm/mach-omap2/cm33xx.c
@@ -1,7 +1,7 @@
 /*
  * AM33XX CM functions
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
  * Reference taken from from OMAP4 cminst44xx.c
diff --git a/arch/arm/mach-omap2/cm33xx.h b/arch/arm/mach-omap2/cm33xx.h
index a91f7d282455..63b362bfc4d9 100644
--- a/arch/arm/mach-omap2/cm33xx.h
+++ b/arch/arm/mach-omap2/cm33xx.h
@@ -1,7 +1,7 @@
 /*
  * AM33XX CM offset macros
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
  * This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/cm81xx.h b/arch/arm/mach-omap2/cm81xx.h
index 5d73a1057c82..bd91223e838e 100644
--- a/arch/arm/mach-omap2/cm81xx.h
+++ b/arch/arm/mach-omap2/cm81xx.h
@@ -1,7 +1,7 @@
 /*
  * Clock domain register offsets for TI81XX.
  *
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
  *
  * This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c
index 46012ca812f4..2000fca6bd4e 100644
--- a/arch/arm/mach-omap2/display.c
+++ b/arch/arm/mach-omap2/display.c
@@ -1,7 +1,7 @@
 /*
  * OMAP2plus display device setup / initialization.
  *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Senthilvadivu Guruswamy
  *	Sumit Semwal
  *
diff --git a/arch/arm/mach-omap2/dma.c b/arch/arm/mach-omap2/dma.c
index 8cc109cc242a..dfc9b21ff19b 100644
--- a/arch/arm/mach-omap2/dma.c
+++ b/arch/arm/mach-omap2/dma.c
@@ -13,7 +13,7 @@
  * Copyright (C) 2009 Texas Instruments
  * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
  *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  * Converted DMA library into platform driver
  *	- G, Manjunath Kondaiah <manjugk@ti.com>
  */
diff --git a/arch/arm/mach-omap2/l3_2xxx.h b/arch/arm/mach-omap2/l3_2xxx.h
index c2bd8d86202b..6297c62428ac 100644
--- a/arch/arm/mach-omap2/l3_2xxx.h
+++ b/arch/arm/mach-omap2/l3_2xxx.h
@@ -2,7 +2,7 @@
 /*
  * arch/arm/plat-omap/include/plat/l3_2xxx.h - L3 firewall definitions
  *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Sumit Semwal
  */
 #ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L3_2XXX_H
diff --git a/arch/arm/mach-omap2/l3_3xxx.h b/arch/arm/mach-omap2/l3_3xxx.h
index 995ebccd13e0..60ea7b201fdc 100644
--- a/arch/arm/mach-omap2/l3_3xxx.h
+++ b/arch/arm/mach-omap2/l3_3xxx.h
@@ -2,7 +2,7 @@
 /*
  * arch/arm/plat-omap/include/plat/l3_3xxx.h - L3 firewall definitions
  *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Sumit Semwal
  */
 #ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L3_3XXX_H
diff --git a/arch/arm/mach-omap2/l4_2xxx.h b/arch/arm/mach-omap2/l4_2xxx.h
index 556e69c2bd00..418e1072d730 100644
--- a/arch/arm/mach-omap2/l4_2xxx.h
+++ b/arch/arm/mach-omap2/l4_2xxx.h
@@ -2,7 +2,7 @@
 /*
  * arch/arm/plat-omap/include/plat/l4_2xxx.h - L4 firewall definitions
  *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Sumit Semwal
  */
 #ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_PLAT_L4_2XXX_H
diff --git a/arch/arm/mach-omap2/omap-iommu.c b/arch/arm/mach-omap2/omap-iommu.c
index bfa5e1b8dba7..93c20bbd7b7e 100644
--- a/arch/arm/mach-omap2/omap-iommu.c
+++ b/arch/arm/mach-omap2/omap-iommu.c
@@ -2,7 +2,7 @@
 /*
  * OMAP IOMMU quirks for various TI SoCs
  *
- * Copyright (C) 2015-2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015-2019 Texas Instruments Incorporated - https://www.ti.com/
  *      Suman Anna <s-anna@ti.com>
  */
 
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
index 5f4ab24dd60d..e29841072287 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
@@ -26,7 +26,6 @@ extern struct omap_hwmod_ocp_if am33xx_mpu__prcm;
 extern struct omap_hwmod_ocp_if am33xx_l3_s__l3_main;
 extern struct omap_hwmod_ocp_if am33xx_gfx__l3_main;
 extern struct omap_hwmod_ocp_if am33xx_l3_main__gfx;
-extern struct omap_hwmod_ocp_if am33xx_l4_wkup__rtc;
 extern struct omap_hwmod_ocp_if am33xx_l3_s__gpmc;
 extern struct omap_hwmod_ocp_if am33xx_l4_ls__timer2;
 extern struct omap_hwmod_ocp_if am33xx_l3_main__ocmc;
@@ -43,7 +42,6 @@ extern struct omap_hwmod am33xx_ocmcram_hwmod;
 extern struct omap_hwmod am33xx_smartreflex0_hwmod;
 extern struct omap_hwmod am33xx_smartreflex1_hwmod;
 extern struct omap_hwmod am33xx_gpmc_hwmod;
-extern struct omap_hwmod am33xx_rtc_hwmod;
 
 extern struct omap_hwmod_class am33xx_emif_hwmod_class;
 extern struct omap_hwmod_class am33xx_l4_hwmod_class;
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
index b389d6589c32..ab5146bfe941 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
@@ -74,30 +74,6 @@ struct omap_hwmod_ocp_if am33xx_l3_s__l3_main = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* gfx -> l3 main */
-struct omap_hwmod_ocp_if am33xx_gfx__l3_main = {
-	.master		= &am33xx_gfx_hwmod,
-	.slave		= &am33xx_l3_main_hwmod,
-	.clk		= "dpll_core_m4_ck",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l3 main -> gfx */
-struct omap_hwmod_ocp_if am33xx_l3_main__gfx = {
-	.master		= &am33xx_l3_main_hwmod,
-	.slave		= &am33xx_gfx_hwmod,
-	.clk		= "dpll_core_m4_ck",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4 wkup -> rtc */
-struct omap_hwmod_ocp_if am33xx_l4_wkup__rtc = {
-	.master		= &am33xx_l4_wkup_hwmod,
-	.slave		= &am33xx_rtc_hwmod,
-	.clk		= "clkdiv32k_ick",
-	.user		= OCP_USER_MPU,
-};
-
 /* l3s cfg -> gpmc */
 struct omap_hwmod_ocp_if am33xx_l3_s__gpmc = {
 	.master		= &am33xx_l3_s_hwmod,
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
index 4b3cd590fb52..bcc120ed610a 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
@@ -26,7 +26,6 @@
 #define CLKCTRL(oh, clkctrl) ((oh).prcm.omap4.clkctrl_offs = (clkctrl))
 #define RSTCTRL(oh, rstctrl) ((oh).prcm.omap4.rstctrl_offs = (rstctrl))
 #define RSTST(oh, rstst) ((oh).prcm.omap4.rstst_offs = (rstst))
-#define PRCM_FLAGS(oh, flag) ((oh).prcm.omap4.flags = (flag))
 
 /*
  * 'l3' class
@@ -133,30 +132,6 @@ struct omap_hwmod_class am33xx_wkup_m3_hwmod_class = {
 	.name		= "wkup_m3",
 };
 
-/* gfx */
-/* Pseudo hwmod for reset control purpose only */
-static struct omap_hwmod_class am33xx_gfx_hwmod_class = {
-	.name	= "gfx",
-};
-
-static struct omap_hwmod_rst_info am33xx_gfx_resets[] = {
-	{ .name = "gfx", .rst_shift = 0, .st_shift = 0},
-};
-
-struct omap_hwmod am33xx_gfx_hwmod = {
-	.name		= "gfx",
-	.class		= &am33xx_gfx_hwmod_class,
-	.clkdm_name	= "gfx_l3_clkdm",
-	.main_clk	= "gfx_fck_div_ck",
-	.prcm		= {
-		.omap4	= {
-			.modulemode	= MODULEMODE_SWCTRL,
-		},
-	},
-	.rst_lines	= am33xx_gfx_resets,
-	.rst_lines_cnt	= ARRAY_SIZE(am33xx_gfx_resets),
-};
-
 /*
  * 'prcm' class
  * power and reset manager (whole prcm infrastructure)
@@ -274,67 +249,24 @@ struct omap_hwmod am33xx_gpmc_hwmod = {
 	},
 };
 
-
-/*
- * 'rtc' class
- * rtc subsystem
- */
-static struct omap_hwmod_class_sysconfig am33xx_rtc_sysc = {
-	.rev_offs	= 0x0074,
-	.sysc_offs	= 0x0078,
-	.sysc_flags	= SYSC_HAS_SIDLEMODE,
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO |
-			  SIDLE_SMART | SIDLE_SMART_WKUP),
-	.sysc_fields	= &omap_hwmod_sysc_type3,
-};
-
-static struct omap_hwmod_class am33xx_rtc_hwmod_class = {
-	.name		= "rtc",
-	.sysc		= &am33xx_rtc_sysc,
-	.unlock		= &omap_hwmod_rtc_unlock,
-	.lock		= &omap_hwmod_rtc_lock,
-};
-
-struct omap_hwmod am33xx_rtc_hwmod = {
-	.name		= "rtc",
-	.class		= &am33xx_rtc_hwmod_class,
-	.clkdm_name	= "l4_rtc_clkdm",
-	.main_clk	= "clk_32768_ck",
-	.prcm		= {
-		.omap4	= {
-			.modulemode	= MODULEMODE_SWCTRL,
-		},
-	},
-};
-
 static void omap_hwmod_am33xx_clkctrl(void)
 {
 	CLKCTRL(am33xx_smartreflex0_hwmod,
 		AM33XX_CM_WKUP_SMARTREFLEX0_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_smartreflex1_hwmod,
 		AM33XX_CM_WKUP_SMARTREFLEX1_CLKCTRL_OFFSET);
-	CLKCTRL(am33xx_rtc_hwmod, AM33XX_CM_RTC_RTC_CLKCTRL_OFFSET);
-	PRCM_FLAGS(am33xx_rtc_hwmod, HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_gpmc_hwmod, AM33XX_CM_PER_GPMC_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l4_ls_hwmod, AM33XX_CM_PER_L4LS_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l4_wkup_hwmod, AM33XX_CM_WKUP_L4WKUP_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l3_main_hwmod, AM33XX_CM_PER_L3_CLKCTRL_OFFSET);
-	CLKCTRL(am33xx_gfx_hwmod, AM33XX_CM_GFX_GFX_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_mpu_hwmod , AM33XX_CM_MPU_MPU_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l3_instr_hwmod , AM33XX_CM_PER_L3_INSTR_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_ocmcram_hwmod , AM33XX_CM_PER_OCMCRAM_CLKCTRL_OFFSET);
 }
 
-static void omap_hwmod_am33xx_rst(void)
-{
-	RSTCTRL(am33xx_gfx_hwmod, AM33XX_RM_GFX_RSTCTRL_OFFSET);
-	RSTST(am33xx_gfx_hwmod, AM33XX_RM_GFX_RSTST_OFFSET);
-}
-
 void omap_hwmod_am33xx_reg(void)
 {
 	omap_hwmod_am33xx_clkctrl();
-	omap_hwmod_am33xx_rst();
 }
 
 static void omap_hwmod_am43xx_clkctrl(void)
@@ -343,25 +275,16 @@ static void omap_hwmod_am43xx_clkctrl(void)
 		AM43XX_CM_WKUP_SMARTREFLEX0_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_smartreflex1_hwmod,
 		AM43XX_CM_WKUP_SMARTREFLEX1_CLKCTRL_OFFSET);
-	CLKCTRL(am33xx_rtc_hwmod, AM43XX_CM_RTC_RTC_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_gpmc_hwmod, AM43XX_CM_PER_GPMC_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l4_ls_hwmod, AM43XX_CM_PER_L4LS_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l4_wkup_hwmod, AM43XX_CM_WKUP_L4WKUP_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l3_main_hwmod, AM43XX_CM_PER_L3_CLKCTRL_OFFSET);
-	CLKCTRL(am33xx_gfx_hwmod, AM43XX_CM_GFX_GFX_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_mpu_hwmod , AM43XX_CM_MPU_MPU_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l3_instr_hwmod , AM43XX_CM_PER_L3_INSTR_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_ocmcram_hwmod , AM43XX_CM_PER_OCMCRAM_CLKCTRL_OFFSET);
 }
 
-static void omap_hwmod_am43xx_rst(void)
-{
-	RSTCTRL(am33xx_gfx_hwmod, AM43XX_RM_GFX_RSTCTRL_OFFSET);
-	RSTST(am33xx_gfx_hwmod, AM43XX_RM_GFX_RSTST_OFFSET);
-}
-
 void omap_hwmod_am43xx_reg(void)
 {
 	omap_hwmod_am43xx_clkctrl();
-	omap_hwmod_am43xx_rst();
 }
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
index 3cf9c4c90b18..b232f6ca6fe3 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
@@ -1,7 +1,7 @@
 /*
  * omap_hwmod_33xx_data.c: Hardware modules present on the AM33XX chips
  *
- * Copyright (C) {2012} Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) {2012} Texas Instruments Incorporated - https://www.ti.com/
  *
  * This file is automatically generated from the AM33XX hardware databases.
  * This program is free software; you can redistribute it and/or
@@ -274,16 +274,13 @@ static struct omap_hwmod_ocp_if *am33xx_hwmod_ocp_ifs[] __initdata = {
 	&am33xx_l3_main__l4_hs,
 	&am33xx_l3_main__l3_s,
 	&am33xx_l3_main__l3_instr,
-	&am33xx_l3_main__gfx,
 	&am33xx_l3_s__l3_main,
 	&am33xx_wkup_m3__l4_wkup,
-	&am33xx_gfx__l3_main,
 	&am33xx_l3_main__debugss,
 	&am33xx_l4_wkup__wkup_m3,
 	&am33xx_l4_wkup__control,
 	&am33xx_l4_wkup__smartreflex0,
 	&am33xx_l4_wkup__smartreflex1,
-	&am33xx_l4_wkup__rtc,
 	&am33xx_l3_s__gpmc,
 	&am33xx_l3_main__ocmc,
 	NULL,
diff --git a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
index b88d12de68a2..b97cb745bbbc 100644
--- a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
@@ -143,11 +143,9 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	&am43xx_l3_main__l4_hs,
 	&am33xx_l3_main__l3_s,
 	&am33xx_l3_main__l3_instr,
-	&am33xx_l3_main__gfx,
 	&am33xx_l3_s__l3_main,
 	&am43xx_l3_main__emif,
 	&am43xx_wkup_m3__l4_wkup,
-	&am33xx_gfx__l3_main,
 	&am43xx_l4_wkup__wkup_m3,
 	&am43xx_l4_wkup__control,
 	&am43xx_l4_wkup__smartreflex0,
@@ -157,11 +155,6 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	NULL,
 };
 
-static struct omap_hwmod_ocp_if *am43xx_rtc_hwmod_ocp_ifs[] __initdata = {
-	&am33xx_l4_wkup__rtc,
-	NULL,
-};
-
 int __init am43xx_hwmod_init(void)
 {
 	int ret;
@@ -170,8 +163,5 @@ int __init am43xx_hwmod_init(void)
 	omap_hwmod_init();
 	ret = omap_hwmod_register_links(am43xx_hwmod_ocp_ifs);
 
-	if (!ret && of_machine_is_compatible("ti,am4372"))
-		ret = omap_hwmod_register_links(am43xx_rtc_hwmod_ocp_ifs);
-
 	return ret;
 }
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 665ca74a834a..37c59115b353 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -124,21 +124,6 @@ static struct omap_hwmod_class omap44xx_l4_hwmod_class = {
 	.name	= "l4",
 };
 
-/* l4_abe */
-static struct omap_hwmod omap44xx_l4_abe_hwmod = {
-	.name		= "l4_abe",
-	.class		= &omap44xx_l4_hwmod_class,
-	.clkdm_name	= "abe_clkdm",
-	.prcm = {
-		.omap4 = {
-			.clkctrl_offs = OMAP4_CM1_ABE_L4ABE_CLKCTRL_OFFSET,
-			.context_offs = OMAP4_RM_ABE_AESS_CONTEXT_OFFSET,
-			.lostcontext_mask = OMAP4430_LOSTMEM_AESSMEM_MASK,
-			.flags	      = HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT,
-		},
-	},
-};
-
 /* l4_cfg */
 static struct omap_hwmod omap44xx_l4_cfg_hwmod = {
 	.name		= "l4_cfg",
@@ -771,22 +756,6 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_3 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l3_main_1 -> l4_abe */
-static struct omap_hwmod_ocp_if omap44xx_l3_main_1__l4_abe = {
-	.master		= &omap44xx_l3_main_1_hwmod,
-	.slave		= &omap44xx_l4_abe_hwmod,
-	.clk		= "l3_div_ck",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* mpu -> l4_abe */
-static struct omap_hwmod_ocp_if omap44xx_mpu__l4_abe = {
-	.master		= &omap44xx_mpu_hwmod,
-	.slave		= &omap44xx_l4_abe_hwmod,
-	.clk		= "ocp_abe_iclk",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
 /* l3_main_1 -> l4_cfg */
 static struct omap_hwmod_ocp_if omap44xx_l3_main_1__l4_cfg = {
 	.master		= &omap44xx_l3_main_1_hwmod,
@@ -988,8 +957,6 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = {
 	&omap44xx_l3_main_1__l3_main_3,
 	&omap44xx_l3_main_2__l3_main_3,
 	&omap44xx_l4_cfg__l3_main_3,
-	&omap44xx_l3_main_1__l4_abe,
-	&omap44xx_mpu__l4_abe,
 	&omap44xx_l3_main_1__l4_cfg,
 	&omap44xx_l3_main_2__l4_per,
 	&omap44xx_l4_cfg__l4_wkup,
diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
index 7c38c1ba58ac..85b9ab4756ed 100644
--- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c
@@ -2,7 +2,7 @@
 /*
  * Hardware modules present on the OMAP54xx chips
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley
  * Benoit Cousson
@@ -121,19 +121,6 @@ static struct omap_hwmod_class omap54xx_l4_hwmod_class = {
 	.name	= "l4",
 };
 
-/* l4_abe */
-static struct omap_hwmod omap54xx_l4_abe_hwmod = {
-	.name		= "l4_abe",
-	.class		= &omap54xx_l4_hwmod_class,
-	.clkdm_name	= "abe_clkdm",
-	.prcm = {
-		.omap4 = {
-			.clkctrl_offs = OMAP54XX_CM_ABE_L4_ABE_CLKCTRL_OFFSET,
-			.flags = HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT,
-		},
-	},
-};
-
 /* l4_cfg */
 static struct omap_hwmod omap54xx_l4_cfg_hwmod = {
 	.name		= "l4_cfg",
@@ -395,22 +382,6 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_3 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l3_main_1 -> l4_abe */
-static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l4_abe = {
-	.master		= &omap54xx_l3_main_1_hwmod,
-	.slave		= &omap54xx_l4_abe_hwmod,
-	.clk		= "abe_iclk",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* mpu -> l4_abe */
-static struct omap_hwmod_ocp_if omap54xx_mpu__l4_abe = {
-	.master		= &omap54xx_mpu_hwmod,
-	.slave		= &omap54xx_l4_abe_hwmod,
-	.clk		= "abe_iclk",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
 /* l3_main_1 -> l4_cfg */
 static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l4_cfg = {
 	.master		= &omap54xx_l3_main_1_hwmod,
@@ -478,8 +449,6 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
 	&omap54xx_l3_main_1__l3_main_3,
 	&omap54xx_l3_main_2__l3_main_3,
 	&omap54xx_l4_cfg__l3_main_3,
-	&omap54xx_l3_main_1__l4_abe,
-	&omap54xx_mpu__l4_abe,
 	&omap54xx_l3_main_1__l4_cfg,
 	&omap54xx_l3_main_2__l4_per,
 	&omap54xx_l3_main_1__l4_wkup,
diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
index adb07848de96..05e163c8337a 100644
--- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
@@ -2,7 +2,7 @@
 /*
  * Hardware modules present on the DRA7xx chips
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley
  * Benoit Cousson
@@ -419,41 +419,6 @@ static struct omap_hwmod dra7xx_qspi_hwmod = {
 };
 
 /*
- * 'rtcss' class
- *
- */
-static struct omap_hwmod_class_sysconfig dra7xx_rtcss_sysc = {
-	.rev_offs	= 0x0074,
-	.sysc_offs	= 0x0078,
-	.sysc_flags	= SYSC_HAS_SIDLEMODE,
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
-			   SIDLE_SMART_WKUP),
-	.sysc_fields	= &omap_hwmod_sysc_type3,
-};
-
-static struct omap_hwmod_class dra7xx_rtcss_hwmod_class = {
-	.name	= "rtcss",
-	.sysc	= &dra7xx_rtcss_sysc,
-	.unlock	= &omap_hwmod_rtc_unlock,
-	.lock	= &omap_hwmod_rtc_lock,
-};
-
-/* rtcss */
-static struct omap_hwmod dra7xx_rtcss_hwmod = {
-	.name		= "rtcss",
-	.class		= &dra7xx_rtcss_hwmod_class,
-	.clkdm_name	= "rtc_clkdm",
-	.main_clk	= "sys_32k_ck",
-	.prcm = {
-		.omap4 = {
-			.clkctrl_offs = DRA7XX_CM_RTC_RTCSS_CLKCTRL_OFFSET,
-			.context_offs = DRA7XX_RM_RTC_RTCSS_CONTEXT_OFFSET,
-			.modulemode   = MODULEMODE_SWCTRL,
-		},
-	},
-};
-
-/*
  * 'sata' class
  *
  */
@@ -702,14 +667,6 @@ static struct omap_hwmod_ocp_if dra7xx_l3_main_1__qspi = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l4_per3 -> rtcss */
-static struct omap_hwmod_ocp_if dra7xx_l4_per3__rtcss = {
-	.master		= &dra7xx_l4_per3_hwmod,
-	.slave		= &dra7xx_rtcss_hwmod,
-	.clk		= "l4_root_clk_div",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
 /* l4_cfg -> sata */
 static struct omap_hwmod_ocp_if dra7xx_l4_cfg__sata = {
 	.master		= &dra7xx_l4_cfg_hwmod,
@@ -786,7 +743,6 @@ static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
 };
 
 static struct omap_hwmod_ocp_if *rtc_hwmod_ocp_ifs[] __initdata = {
-	&dra7xx_l4_per3__rtcss,
 	NULL,
 };
 
diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
index 50fb699b163f..450ab990c66a 100644
--- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
@@ -1,7 +1,7 @@
 /*
  * DM81xx hwmod data.
  *
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
  *
  * This program is free software; you can redistribute it and/or
diff --git a/arch/arm/mach-omap2/omap_opp_data.h b/arch/arm/mach-omap2/omap_opp_data.h
index 336fdfcf88bb..533dd643069a 100644
--- a/arch/arm/mach-omap2/omap_opp_data.h
+++ b/arch/arm/mach-omap2/omap_opp_data.h
@@ -1,7 +1,7 @@
 /*
  * OMAP SoC specific OPP Data helpers
  *
- * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2009-2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Nishanth Menon
  *	Kevin Hilman
  * Copyright (C) 2010 Nokia Corporation.
diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index d2925e8b2eff..6f6a6a66c981 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -3,7 +3,7 @@
   * This file configures the internal USB PHY in OMAP4430. Used
   * with TWL6030 transceiver and MUSB on OMAP4430.
   *
-  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com
+  * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com
   * Author: Hema HK <hemahk@ti.com>
   */
 
diff --git a/arch/arm/mach-omap2/opp3xxx_data.c b/arch/arm/mach-omap2/opp3xxx_data.c
index c2d459f5b0da..b610c5fb423b 100644
--- a/arch/arm/mach-omap2/opp3xxx_data.c
+++ b/arch/arm/mach-omap2/opp3xxx_data.c
@@ -1,7 +1,7 @@
 /*
  * OMAP3 OPP table definitions.
  *
- * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2009-2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Nishanth Menon
  *	Kevin Hilman
  * Copyright (C) 2010-2011 Nokia Corporation.
diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c
index 985aeab9bc2a..d937c5ef41c6 100644
--- a/arch/arm/mach-omap2/opp4xxx_data.c
+++ b/arch/arm/mach-omap2/opp4xxx_data.c
@@ -1,7 +1,7 @@
 /*
  * OMAP4 OPP table definitions.
  *
- * Copyright (C) 2010-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2010-2012 Texas Instruments Incorporated - https://www.ti.com/
  *	Nishanth Menon
  *	Kevin Hilman
  *	Thara Gopinath
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
index fceb1e525d26..919d35d5b325 100644
--- a/arch/arm/mach-omap2/pm-debug.c
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -34,8 +34,6 @@
 #include "prm2xxx_3xxx.h"
 #include "pm.h"
 
-u32 enable_off_mode;
-
 #ifdef CONFIG_DEBUG_FS
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index 01ec1ba4878b..da829a90fe8c 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -28,6 +28,8 @@
 #include "clockdomain.h"
 #include "pm.h"
 
+u32 enable_off_mode;
+
 #ifdef CONFIG_SUSPEND
 /*
  * omap_pm_suspend: points to a function that does the SoC-specific
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index 2a883a0c1fcd..80e84ae66aee 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -49,11 +49,7 @@ static inline int omap4_opp_init(void)
 extern int omap3_pm_get_suspend_state(struct powerdomain *pwrdm);
 extern int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state);
 
-#ifdef CONFIG_PM_DEBUG
 extern u32 enable_off_mode;
-#else
-#define enable_off_mode 0
-#endif
 
 #if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
 extern void pm_dbg_update_time(struct powerdomain *pwrdm, int prev);
diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c
index 58236c7dc83e..56f2c0bcae5a 100644
--- a/arch/arm/mach-omap2/pm33xx-core.c
+++ b/arch/arm/mach-omap2/pm33xx-core.c
@@ -2,7 +2,7 @@
 /*
  * AM33XX Arch Power Management Routines
  *
- * Copyright (C) 2016-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016-2018 Texas Instruments Incorporated - https://www.ti.com/
  *	Dave Gerlach
  */
 
@@ -25,7 +25,6 @@
 #include "control.h"
 #include "clockdomain.h"
 #include "iomap.h"
-#include "omap_hwmod.h"
 #include "pm.h"
 #include "powerdomain.h"
 #include "prm33xx.h"
@@ -36,7 +35,6 @@
 static struct powerdomain *cefuse_pwrdm, *gfx_pwrdm, *per_pwrdm, *mpu_pwrdm;
 static struct clockdomain *gfx_l4ls_clkdm;
 static void __iomem *scu_base;
-static struct omap_hwmod *rtc_oh;
 
 static int (*idle_fn)(u32 wfi_flags);
 
@@ -267,13 +265,6 @@ static struct am33xx_pm_sram_addr *amx3_get_sram_addrs(void)
 		return NULL;
 }
 
-static void __iomem *am43xx_get_rtc_base_addr(void)
-{
-	rtc_oh = omap_hwmod_lookup("rtc");
-
-	return omap_hwmod_get_mpu_rt_va(rtc_oh);
-}
-
 static void am43xx_save_context(void)
 {
 }
@@ -297,16 +288,6 @@ static void am43xx_restore_context(void)
 	writel_relaxed(0x0, AM33XX_L4_WK_IO_ADDRESS(0x44df2e14));
 }
 
-static void am43xx_prepare_rtc_suspend(void)
-{
-	omap_hwmod_enable(rtc_oh);
-}
-
-static void am43xx_prepare_rtc_resume(void)
-{
-	omap_hwmod_idle(rtc_oh);
-}
-
 static struct am33xx_pm_platform_data am33xx_ops = {
 	.init = am33xx_suspend_init,
 	.deinit = amx3_suspend_deinit,
@@ -317,10 +298,7 @@ static struct am33xx_pm_platform_data am33xx_ops = {
 	.get_sram_addrs = amx3_get_sram_addrs,
 	.save_context = am33xx_save_context,
 	.restore_context = am33xx_restore_context,
-	.prepare_rtc_suspend = am43xx_prepare_rtc_suspend,
-	.prepare_rtc_resume = am43xx_prepare_rtc_resume,
 	.check_off_mode_enable = am33xx_check_off_mode_enable,
-	.get_rtc_base_addr = am43xx_get_rtc_base_addr,
 };
 
 static struct am33xx_pm_platform_data am43xx_ops = {
@@ -333,10 +311,7 @@ static struct am33xx_pm_platform_data am43xx_ops = {
 	.get_sram_addrs = amx3_get_sram_addrs,
 	.save_context = am43xx_save_context,
 	.restore_context = am43xx_restore_context,
-	.prepare_rtc_suspend = am43xx_prepare_rtc_suspend,
-	.prepare_rtc_resume = am43xx_prepare_rtc_resume,
 	.check_off_mode_enable = am43xx_check_off_mode_enable,
-	.get_rtc_base_addr = am43xx_get_rtc_base_addr,
 };
 
 static struct am33xx_pm_platform_data *am33xx_pm_get_pdata(void)
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index f5dfddf492e2..71c1d18aafbc 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -25,6 +25,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/slab.h>
+#include <linux/of.h>
 #include <linux/omap-gpmc.h>
 
 #include <trace/events/power.h>
@@ -410,7 +411,12 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 	if (!pwrst)
 		return -ENOMEM;
 	pwrst->pwrdm = pwrdm;
-	pwrst->next_state = PWRDM_POWER_RET;
+
+	if (enable_off_mode)
+		pwrst->next_state = PWRDM_POWER_OFF;
+	else
+		pwrst->next_state = PWRDM_POWER_RET;
+
 	list_add(&pwrst->node, &pwrst_list);
 
 	if (pwrdm_has_hdwr_sar(pwrdm))
@@ -444,6 +450,22 @@ static void __init pm_errata_configure(void)
 	}
 }
 
+static void __init omap3_pm_check_pmic(void)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "ti,twl4030-power-idle");
+	if (!np)
+		np = of_find_compatible_node(NULL, NULL, "ti,twl4030-power-idle-osc-off");
+
+	if (np) {
+		of_node_put(np);
+		enable_off_mode = 1;
+	} else {
+		enable_off_mode = 0;
+	}
+}
+
 int __init omap3_pm_init(void)
 {
 	struct power_state *pwrst, *tmp;
@@ -477,6 +499,8 @@ int __init omap3_pm_init(void)
 		goto err2;
 	}
 
+	omap3_pm_check_pmic();
+
 	ret = pwrdm_for_each(pwrdms_setup, NULL);
 	if (ret) {
 		pr_err("Failed to setup powerdomains\n");
diff --git a/arch/arm/mach-omap2/powerdomains33xx_data.c b/arch/arm/mach-omap2/powerdomains33xx_data.c
index 869adb82569e..626055e59aed 100644
--- a/arch/arm/mach-omap2/powerdomains33xx_data.c
+++ b/arch/arm/mach-omap2/powerdomains33xx_data.c
@@ -1,7 +1,7 @@
 /*
  * AM33XX Power domain data
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prcm43xx.h b/arch/arm/mach-omap2/prcm43xx.h
index 7078a61c1d3f..899da0ae9800 100644
--- a/arch/arm/mach-omap2/prcm43xx.h
+++ b/arch/arm/mach-omap2/prcm43xx.h
@@ -1,7 +1,7 @@
 /*
  * AM43x PRCM defines
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This file is licensed under the terms of the GNU General Public License
  * version 2.  This program is licensed "as is" without any warranty of any
diff --git a/arch/arm/mach-omap2/prcm_mpu54xx.h b/arch/arm/mach-omap2/prcm_mpu54xx.h
index 6ef38829c064..bdbfa070b08e 100644
--- a/arch/arm/mach-omap2/prcm_mpu54xx.h
+++ b/arch/arm/mach-omap2/prcm_mpu54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54xx PRCM MPU instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley (paul@pwsan.com)
  * Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/prcm_mpu7xx.h b/arch/arm/mach-omap2/prcm_mpu7xx.h
index 33d0013aa1d4..2e3032440ea0 100644
--- a/arch/arm/mach-omap2/prcm_mpu7xx.h
+++ b/arch/arm/mach-omap2/prcm_mpu7xx.h
@@ -2,7 +2,7 @@
 /*
  * DRA7xx PRCM MPU instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Generated by code originally written by:
  * Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/prm-regbits-33xx.h b/arch/arm/mach-omap2/prm-regbits-33xx.h
index 84feecee4fe6..7dfdff09ddeb 100644
--- a/arch/arm/mach-omap2/prm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-33xx.h
@@ -1,7 +1,7 @@
 /*
  * AM33XX PRM_XXX register bits
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm33xx.c b/arch/arm/mach-omap2/prm33xx.c
index d5141669c28d..9144cc0479af 100644
--- a/arch/arm/mach-omap2/prm33xx.c
+++ b/arch/arm/mach-omap2/prm33xx.c
@@ -1,7 +1,7 @@
 /*
  * AM33XX PRM functions
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm33xx.h b/arch/arm/mach-omap2/prm33xx.h
index 66302c6aba61..d0b7404565f1 100644
--- a/arch/arm/mach-omap2/prm33xx.h
+++ b/arch/arm/mach-omap2/prm33xx.h
@@ -1,7 +1,7 @@
 /*
  * AM33XX PRM instance offset macros
  *
- * Copyright (C) 2011-2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/prm54xx.h b/arch/arm/mach-omap2/prm54xx.h
index ee0f1cc92e3a..7329d6fcd78b 100644
--- a/arch/arm/mach-omap2/prm54xx.h
+++ b/arch/arm/mach-omap2/prm54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54xx PRM instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Paul Walmsley (paul@pwsan.com)
  * Rajendra Nayak (rnayak@ti.com)
diff --git a/arch/arm/mach-omap2/prm7xx.h b/arch/arm/mach-omap2/prm7xx.h
index cf99307d1b1f..e5aee0409eae 100644
--- a/arch/arm/mach-omap2/prm7xx.h
+++ b/arch/arm/mach-omap2/prm7xx.h
@@ -2,7 +2,7 @@
 /*
  * DRA7xx PRM instance offset macros
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Generated by code originally written by:
  * Paul Walmsley (paul@pwsan.com)
diff --git a/arch/arm/mach-omap2/scrm54xx.h b/arch/arm/mach-omap2/scrm54xx.h
index 810d2b186337..cb6f3e6a7095 100644
--- a/arch/arm/mach-omap2/scrm54xx.h
+++ b/arch/arm/mach-omap2/scrm54xx.h
@@ -2,7 +2,7 @@
 /*
  * OMAP54XX SCRM registers and bitfields
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  *
  * Benoit Cousson (b-cousson@ti.com)
  *
diff --git a/arch/arm/mach-omap2/sleep33xx.S b/arch/arm/mach-omap2/sleep33xx.S
index dc221249bc22..ac3d0b363c51 100644
--- a/arch/arm/mach-omap2/sleep33xx.S
+++ b/arch/arm/mach-omap2/sleep33xx.S
@@ -2,7 +2,7 @@
 /*
  * Low level suspend code for AM33XX SoCs
  *
- * Copyright (C) 2012-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012-2018 Texas Instruments Incorporated - https://www.ti.com/
  *	Dave Gerlach, Vaibhav Bedia
  */
 
diff --git a/arch/arm/mach-omap2/sleep43xx.S b/arch/arm/mach-omap2/sleep43xx.S
index 90d2907a2eb2..832c91327945 100644
--- a/arch/arm/mach-omap2/sleep43xx.S
+++ b/arch/arm/mach-omap2/sleep43xx.S
@@ -2,7 +2,7 @@
 /*
  * Low level suspend code for AM43XX SoCs
  *
- * Copyright (C) 2013-2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013-2018 Texas Instruments Incorporated - https://www.ti.com/
  *	Dave Gerlach, Vaibhav Bedia
  */
 
diff --git a/arch/arm/mach-omap2/ti81xx.h b/arch/arm/mach-omap2/ti81xx.h
index a1e6caf0dba6..192b0e7d3eb4 100644
--- a/arch/arm/mach-omap2/ti81xx.h
+++ b/arch/arm/mach-omap2/ti81xx.h
@@ -1,7 +1,7 @@
 /*
  * This file contains the address data for various TI81XX modules.
  *
- * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
+ * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
diff --git a/arch/arm/mach-omap2/voltagedomains54xx_data.c b/arch/arm/mach-omap2/voltagedomains54xx_data.c
index aac274d6a93b..e60d76db0f21 100644
--- a/arch/arm/mach-omap2/voltagedomains54xx_data.c
+++ b/arch/arm/mach-omap2/voltagedomains54xx_data.c
@@ -4,7 +4,7 @@
  *
  * Based on voltagedomains44xx_data.c
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
  */
 #include <linux/kernel.h>
 #include <linux/err.h>
diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/mach-s3c/Kconfig
index 301e572651c0..25606e668cf9 100644
--- a/arch/arm/plat-samsung/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig
@@ -2,12 +2,16 @@
 #
 # Copyright 2009 Simtec Electronics
 
+source "arch/arm/mach-s3c/Kconfig.s3c24xx"
+source "arch/arm/mach-s3c/Kconfig.s3c64xx"
+
 config PLAT_SAMSUNG
 	bool
-	depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_EXYNOS || ARCH_S5PV210
+	depends on PLAT_S3C24XX || ARCH_S3C64XX
 	default y
 	select GENERIC_IRQ_CHIP
 	select NO_IOPORT_MAP
+	select SOC_SAMSUNG
 	help
 	  Base platform code for all Samsung SoC based systems
 
@@ -154,7 +158,7 @@ config S3C_DEV_WDT
 	bool
 	default y if ARCH_S3C24XX
 	help
-	  Complie in platform device definition for Watchdog Timer
+	  Compile in platform device definition for Watchdog Timer
 
 config S3C_DEV_NAND
 	bool
@@ -169,7 +173,7 @@ config S3C_DEV_ONENAND
 config S3C_DEV_RTC
 	bool
 	help
-	  Complie in platform device definition for RTC
+	  Compile in platform device definition for RTC
 
 config SAMSUNG_DEV_ADC
 	bool
@@ -234,54 +238,6 @@ config SAMSUNG_PM_GPIO
 	  pinctrl-samsung driver.
 endif
 
-comment "Power management"
-
-config SAMSUNG_PM_DEBUG
-	bool "Samsung PM Suspend debug"
-	depends on PM && DEBUG_KERNEL
-	depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
-	depends on DEBUG_EXYNOS_UART || DEBUG_S3C24XX_UART || DEBUG_S3C2410_UART
-	help
-	  Say Y here if you want verbose debugging from the PM Suspend and
-	  Resume code. See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
-	  for more information.
-
-config S3C_PM_DEBUG_LED_SMDK
-       bool "SMDK LED suspend/resume debugging"
-       depends on PM && (MACH_SMDK6410)
-       help
-         Say Y here to enable the use of the SMDK LEDs on the baseboard
-	 for debugging of the state of the suspend and resume process.
-
-	 Note, this currently only works for S3C64XX based SMDK boards.
-
-config SAMSUNG_PM_CHECK
-	bool "S3C2410 PM Suspend Memory CRC"
-	depends on PM && (PLAT_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210)
-	select CRC32
-	help
-	  Enable the PM code's memory area checksum over sleep. This option
-	  will generate CRCs of all blocks of memory, and store them before
-	  going to sleep. The blocks are then checked on resume for any
-	  errors.
-
-	  Note, this can take several seconds depending on memory size
-	  and CPU speed.
-
-	  See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
-
-config SAMSUNG_PM_CHECK_CHUNKSIZE
-	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
-	depends on PM && SAMSUNG_PM_CHECK
-	default 64
-	help
-	  Set the chunksize in Kilobytes of the CRC for checking memory
-	  corruption over suspend and resume. A smaller value will mean that
-	  the CRC data block will take more memory, but will identify any
-	  faults with better precision.
-
-	  See <file:Documentation/arm/samsung-s3c24xx/suspend.rst>
-
 config SAMSUNG_WAKEMASK
 	bool
 	depends on PM
@@ -290,19 +246,5 @@ config SAMSUNG_WAKEMASK
 	  and above. This code allows a set of interrupt to wakeup-mask
 	  mappings. See <plat/wakeup-mask.h>
 
-config SAMSUNG_WDT_RESET
-	bool
-	help
-	  Compile support for system restart by triggering watchdog reset.
-	  Used on SoCs that do not provide dedicated reset control.
-
-config DEBUG_S3C_UART
-	depends on PLAT_SAMSUNG
-	int
-	default "0" if DEBUG_S3C_UART0
-	default "1" if DEBUG_S3C_UART1
-	default "2" if DEBUG_S3C_UART2
-	default "3" if DEBUG_S3C_UART3
-
 endmenu
 endif
diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c/Kconfig.s3c24xx
index 7673dde9671a..000e3e234f71 100644
--- a/arch/arm/mach-s3c24xx/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig.s3c24xx
@@ -123,11 +123,6 @@ config S3C24XX_PLL
 	  This also means that the PLL tables for the selected CPU(s) will
 	  be built which may increase the size of the kernel image.
 
-config S3C_SETUP_CAMIF
-	bool
-	help
-	  Compile in common setup code for S3C CAMIF devices
-
 # cpu frequency items common between s3c2410 and s3c2440/s3c2442
 
 config S3C2410_IOTIMING
@@ -137,13 +132,6 @@ config S3C2410_IOTIMING
 	  Internal node to select io timing code that is common to the s3c2410
 	  and s3c2440/s3c2442 cpu frequency support.
 
-config S3C2410_CPUFREQ_UTILS
-       bool
-       depends on ARM_S3C24XX_CPUFREQ
-       help
-         Internal node to select timing code that is common to the s3c2410
-         and s3c2440/s3c244 cpu frequency support.
-
 # cpu frequency support common to s3c2412, s3c2413 and s3c2442
 
 config S3C2412_IOTIMING
@@ -468,7 +456,6 @@ config MACH_MINI2440
 	select NEW_LEDS
 	select S3C_DEV_NAND
 	select S3C_DEV_USB_HOST
-	select S3C_SETUP_CAMIF
 	help
 	  Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
 	  available via various sources. It can come with a 3.5" or 7" touch LCD.
diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c/Kconfig.s3c64xx
index ac3e3563487f..f3fcb570edf5 100644
--- a/arch/arm/mach-s3c64xx/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig.s3c64xx
@@ -13,15 +13,15 @@ menuconfig ARCH_S3C64XX
 	select GPIO_SAMSUNG if ATAGS
 	select GPIOLIB
 	select HAVE_S3C2410_I2C if I2C
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select HAVE_TCM
 	select PLAT_SAMSUNG
 	select PM_GENERIC_DOMAINS if PM
 	select S3C_DEV_NAND if ATAGS
 	select S3C_GPIO_TRACK if ATAGS
+	select S3C2410_WATCHDOG
 	select SAMSUNG_ATAGS if ATAGS
 	select SAMSUNG_WAKEMASK if PM
-	select SAMSUNG_WDT_RESET
+	select WATCHDOG
 	help
 	  Samsung S3C64XX series based systems
 
@@ -165,7 +165,6 @@ config MACH_SMDK6410
 	bool "SMDK6410"
 	depends on ATAGS
 	select CPU_S3C6410
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C64XX_SETUP_I2C1
 	select S3C64XX_SETUP_IDE
diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/mach-s3c/Makefile
index 3db9d2c38258..54188d10ab2e 100644
--- a/arch/arm/plat-samsung/Makefile
+++ b/arch/arm/mach-s3c/Makefile
@@ -2,9 +2,16 @@
 #
 # Copyright 2009 Simtec Electronics
 
-ccflags-$(CONFIG_ARCH_S3C64XX) := -I$(srctree)/arch/arm/mach-s3c64xx/include
 ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include
 
+ifdef CONFIG_ARCH_S3C24XX
+include $(src)/Makefile.s3c24xx
+endif
+
+ifdef CONFIG_ARCH_S3C64XX
+include $(src)/Makefile.s3c64xx
+endif
+
 # Objects we always build independent of SoC choice
 
 obj-y				+= init.o cpu.o
@@ -24,12 +31,7 @@ obj-$(CONFIG_GPIO_SAMSUNG)     += gpio-samsung.o
 
 # PM support
 
-obj-$(CONFIG_PM_SLEEP)		+= pm-common.o
-obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm-common.o
-obj-$(CONFIG_SAMSUNG_PM)	+= pm.o
+obj-$(CONFIG_SAMSUNG_PM)	+= pm.o pm-common.o
 obj-$(CONFIG_SAMSUNG_PM_GPIO)	+= pm-gpio.o
-obj-$(CONFIG_SAMSUNG_PM_CHECK)	+= pm-check.o
-obj-$(CONFIG_SAMSUNG_PM_DEBUG)	+= pm-debug.o
 
 obj-$(CONFIG_SAMSUNG_WAKEMASK)	+= wakeup-mask.o
-obj-$(CONFIG_SAMSUNG_WDT_RESET)	+= watchdog-reset.o
diff --git a/arch/arm/mach-s3c24xx/Makefile.boot b/arch/arm/mach-s3c/Makefile.boot
index 7f19e226035e..7f19e226035e 100644
--- a/arch/arm/mach-s3c24xx/Makefile.boot
+++ b/arch/arm/mach-s3c/Makefile.boot
diff --git a/arch/arm/mach-s3c24xx/Makefile b/arch/arm/mach-s3c/Makefile.s3c24xx
index 6692f2de71b2..3483ab3a2b81 100644
--- a/arch/arm/mach-s3c24xx/Makefile
+++ b/arch/arm/mach-s3c/Makefile.s3c24xx
@@ -7,7 +7,10 @@
 
 # core
 
-obj-y				+= common.o
+obj-y				+= s3c24xx.o
+obj-y				+= irq-s3c24xx.o
+obj-$(CONFIG_SPI_S3C24XX_FIQ)	+= irq-s3c24xx-fiq.o
+obj-$(CONFIG_SPI_S3C24XX_FIQ)	+= irq-s3c24xx-fiq-exports.o
 
 obj-$(CONFIG_CPU_S3C2410)	+= s3c2410.o
 obj-$(CONFIG_S3C2410_PLL)	+= pll-s3c2410.o
@@ -30,12 +33,12 @@ obj-$(CONFIG_CPU_S3C2443)	+= s3c2443.o
 
 # PM
 
-obj-$(CONFIG_PM)		+= pm.o
-obj-$(CONFIG_PM_SLEEP)		+= irq-pm.o sleep.o
+obj-$(CONFIG_PM)		+= pm-s3c24xx.o
+obj-$(CONFIG_PM_SLEEP)		+= irq-pm-s3c24xx.o sleep-s3c24xx.o
 
 # common code
 
-obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += cpufreq-utils.o
+obj-$(CONFIG_ARM_S3C24XX_CPUFREQ) += cpufreq-utils-s3c24xx.o
 
 obj-$(CONFIG_S3C2410_IOTIMING)	+= iotiming-s3c2410.o
 obj-$(CONFIG_S3C2412_IOTIMING)	+= iotiming-s3c2412.o
@@ -80,7 +83,7 @@ obj-$(CONFIG_MACH_SMDK2443)		+= mach-smdk2443.o
 
 # common bits of machine support
 
-obj-$(CONFIG_S3C24XX_SMDK)		+= common-smdk.o
+obj-$(CONFIG_S3C24XX_SMDK)		+= common-smdk-s3c24xx.o
 obj-$(CONFIG_S3C24XX_SIMTEC_AUDIO)	+= simtec-audio.o
 obj-$(CONFIG_S3C24XX_SIMTEC_NOR)	+= simtec-nor.o
 obj-$(CONFIG_S3C24XX_SIMTEC_PM)		+= simtec-pm.o
@@ -93,8 +96,7 @@ obj-$(CONFIG_MACH_OSIRIS_DVS)		+= mach-osiris-dvs.o
 
 # device setup
 
-obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
-obj-$(CONFIG_S3C2443_SETUP_SPI)		+= setup-spi.o
-obj-$(CONFIG_ARCH_S3C24XX)		+= setup-i2c.o
-obj-$(CONFIG_S3C24XX_SETUP_TS)		+= setup-ts.o
-obj-$(CONFIG_S3C_SETUP_CAMIF)		+= setup-camif.o
+obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio-s3c24xx.o
+obj-$(CONFIG_S3C2443_SETUP_SPI)		+= setup-spi-s3c24xx.o
+obj-$(CONFIG_ARCH_S3C24XX)		+= setup-i2c-s3c24xx.o
+obj-$(CONFIG_S3C24XX_SETUP_TS)		+= setup-ts-s3c24xx.o
diff --git a/arch/arm/mach-s3c64xx/Makefile b/arch/arm/mach-s3c/Makefile.s3c64xx
index 8caeb4ad17e9..0c18e31936df 100644
--- a/arch/arm/mach-s3c64xx/Makefile
+++ b/arch/arm/mach-s3c/Makefile.s3c64xx
@@ -3,22 +3,22 @@
 # Copyright 2008 Openmoko, Inc.
 # Copyright 2008 Simtec Electronics
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
-asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
+ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
 
 # PM
 
-obj-$(CONFIG_PM)		+= pm.o
-obj-$(CONFIG_PM_SLEEP)		+= sleep.o
-obj-$(CONFIG_CPU_IDLE)		+= cpuidle.o
+obj-$(CONFIG_PM)		+= pm-s3c64xx.o
+obj-$(CONFIG_PM_SLEEP)		+= sleep-s3c64xx.o
+obj-$(CONFIG_CPU_IDLE)		+= cpuidle-s3c64xx.o
 
 ifdef CONFIG_SAMSUNG_ATAGS
 
-obj-$(CONFIG_PM_SLEEP)          += irq-pm.o
+obj-$(CONFIG_PM_SLEEP)          += irq-pm-s3c64xx.o
 
 # Core
 
-obj-y				+= common.o
+obj-y				+= s3c64xx.o
 obj-$(CONFIG_CPU_S3C6400)	+= s3c6400.o
 obj-$(CONFIG_CPU_S3C6410)	+= s3c6410.o
 
@@ -28,21 +28,21 @@ obj-$(CONFIG_S3C64XX_PL080)	+= pl080.o
 
 # Device support
 
-obj-y				+= dev-uart.o
-obj-y				+= dev-audio.o
+obj-y				+= dev-uart-s3c64xx.o
+obj-y				+= dev-audio-s3c64xx.o
 
 # Device setup
 
-obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
-obj-$(CONFIG_S3C64XX_SETUP_I2C0)	+= setup-i2c0.o
-obj-$(CONFIG_S3C64XX_SETUP_I2C1)	+= setup-i2c1.o
-obj-$(CONFIG_S3C64XX_SETUP_IDE)		+= setup-ide.o
-obj-$(CONFIG_S3C64XX_SETUP_KEYPAD)	+= setup-keypad.o
-obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
-obj-$(CONFIG_S3C64XX_SETUP_SPI)		+= setup-spi.o
-obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy.o
+obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP)	+= setup-fb-24bpp-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_I2C0)	+= setup-i2c0-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_I2C1)	+= setup-i2c1-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_IDE)		+= setup-ide-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_KEYPAD)	+= setup-keypad-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_SPI)		+= setup-spi-s3c64xx.o
+obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy-s3c64xx.o
 
-obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT)	+= dev-backlight.o
+obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT)	+= dev-backlight-s3c64xx.o
 
 # Machine support
 
diff --git a/arch/arm/plat-samsung/include/plat/adc-core.h b/arch/arm/mach-s3c/adc-core.h
index 039f6862b6a7..039f6862b6a7 100644
--- a/arch/arm/plat-samsung/include/plat/adc-core.h
+++ b/arch/arm/mach-s3c/adc-core.h
diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/mach-s3c/adc.c
index 55b1925f65d7..0232520d3c13 100644
--- a/arch/arm/plat-samsung/adc.c
+++ b/arch/arm/mach-s3c/adc.c
@@ -19,8 +19,8 @@
 #include <linux/io.h>
 #include <linux/regulator/consumer.h>
 
-#include <plat/regs-adc.h>
-#include <plat/adc.h>
+#include "regs-adc.h"
+#include <linux/soc/samsung/s3c-adc.h>
 
 /* This driver is designed to control the usage of the ADC block between
  * the touchscreen and any other drivers that may need to use it, such as
diff --git a/arch/arm/mach-s3c24xx/anubis.h b/arch/arm/mach-s3c/anubis.h
index 13847292e6c7..13847292e6c7 100644
--- a/arch/arm/mach-s3c24xx/anubis.h
+++ b/arch/arm/mach-s3c/anubis.h
diff --git a/arch/arm/mach-s3c64xx/ata-core.h b/arch/arm/mach-s3c/ata-core-s3c64xx.h
index 6d9a81f759e6..4863ad9d3a42 100644
--- a/arch/arm/mach-s3c64xx/ata-core.h
+++ b/arch/arm/mach-s3c/ata-core-s3c64xx.h
@@ -6,8 +6,8 @@
  * Samsung CF-ATA Controller core functions
  */
 
-#ifndef __ASM_PLAT_ATA_CORE_H
-#define __ASM_PLAT_ATA_CORE_H __FILE__
+#ifndef __ASM_PLAT_ATA_CORE_S3C64XX_H
+#define __ASM_PLAT_ATA_CORE_S3C64XX_H __FILE__
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
@@ -21,4 +21,4 @@ static inline void s3c_cfcon_setname(char *name)
 #endif
 }
 
-#endif /* __ASM_PLAT_ATA_CORE_H */
+#endif /* __ASM_PLAT_ATA_CORE_S3C64XX_H */
diff --git a/arch/arm/mach-s3c64xx/backlight.h b/arch/arm/mach-s3c/backlight-s3c64xx.h
index 028663f1cacc..2a2b35821d58 100644
--- a/arch/arm/mach-s3c64xx/backlight.h
+++ b/arch/arm/mach-s3c/backlight-s3c64xx.h
@@ -4,8 +4,8 @@
  *              http://www.samsung.com
  */
 
-#ifndef __ASM_PLAT_BACKLIGHT_H
-#define __ASM_PLAT_BACKLIGHT_H __FILE__
+#ifndef __ASM_PLAT_BACKLIGHT_S3C64XX_H
+#define __ASM_PLAT_BACKLIGHT_S3C64XX_H __FILE__
 
 /* samsung_bl_gpio_info - GPIO info for PWM Backlight control
  * @no:		GPIO number for PWM timer out
@@ -19,4 +19,4 @@ struct samsung_bl_gpio_info {
 extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
 	struct platform_pwm_backlight_data *bl_data);
 
-#endif /* __ASM_PLAT_BACKLIGHT_H */
+#endif /* __ASM_PLAT_BACKLIGHT_S3C64XX_H */
diff --git a/arch/arm/mach-s3c24xx/bast-ide.c b/arch/arm/mach-s3c/bast-ide.c
index 067944398f46..da64db1811d8 100644
--- a/arch/arm/mach-s3c24xx/bast-ide.c
+++ b/arch/arm/mach-s3c/bast-ide.c
@@ -19,7 +19,8 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/map.h>
+#include "map.h"
+#include <mach/irqs.h>
 
 #include "bast.h"
 
diff --git a/arch/arm/mach-s3c24xx/bast-irq.c b/arch/arm/mach-s3c/bast-irq.c
index 03728058d58d..d299f124e6dc 100644
--- a/arch/arm/mach-s3c24xx/bast-irq.c
+++ b/arch/arm/mach-s3c/bast-irq.c
@@ -15,8 +15,8 @@
 #include <asm/mach-types.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-irq.h>
+#include "regs-irq.h"
+#include <mach/irqs.h>
 
 #include "bast.h"
 
@@ -62,7 +62,7 @@ bast_pc104_mask(struct irq_data *data)
 static void
 bast_pc104_maskack(struct irq_data *data)
 {
-	struct irq_desc *desc = irq_desc + BAST_IRQ_ISA;
+	struct irq_desc *desc = irq_to_desc(BAST_IRQ_ISA);
 
 	bast_pc104_mask(data);
 	desc->irq_data.chip->irq_ack(&desc->irq_data);
@@ -94,8 +94,6 @@ static void bast_irq_pc104_demux(struct irq_desc *desc)
 
 	if (unlikely(stat == 0)) {
 		/* ack if we get an irq with nothing (ie, startup) */
-
-		desc = irq_desc + BAST_IRQ_ISA;
 		desc->irq_data.chip->irq_ack(&desc->irq_data);
 	} else {
 		/* handle the IRQ */
diff --git a/arch/arm/mach-s3c24xx/bast.h b/arch/arm/mach-s3c/bast.h
index a7726f93f5eb..a7726f93f5eb 100644
--- a/arch/arm/mach-s3c24xx/bast.h
+++ b/arch/arm/mach-s3c/bast.h
diff --git a/arch/arm/mach-s3c24xx/common-smdk.c b/arch/arm/mach-s3c/common-smdk-s3c24xx.c
index 121646ad1bb1..f860d8bcba0e 100644
--- a/arch/arm/mach-s3c24xx/common-smdk.c
+++ b/arch/arm/mach-s3c/common-smdk-s3c24xx.c
@@ -29,19 +29,18 @@
 #include <asm/mach/irq.h>
 
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <linux/platform_data/leds-s3c24xx.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "pm.h"
 
-#include "common-smdk.h"
+#include "common-smdk-s3c24xx.h"
 
 /* LED devices */
 
diff --git a/arch/arm/mach-s3c24xx/common-smdk.h b/arch/arm/mach-s3c/common-smdk-s3c24xx.h
index c0352b06e435..c0352b06e435 100644
--- a/arch/arm/mach-s3c24xx/common-smdk.h
+++ b/arch/arm/mach-s3c/common-smdk-s3c24xx.h
diff --git a/arch/arm/plat-samsung/cpu.c b/arch/arm/mach-s3c/cpu.c
index e1ba88ba31d8..6e9772555f0d 100644
--- a/arch/arm/plat-samsung/cpu.c
+++ b/arch/arm/mach-s3c/cpu.c
@@ -10,17 +10,10 @@
 #include <linux/init.h>
 #include <linux/io.h>
 
-#include <plat/map-base.h>
-#include <plat/cpu.h>
+#include <mach/map-base.h>
+#include "cpu.h"
 
 unsigned long samsung_cpu_id;
-static unsigned int samsung_cpu_rev;
-
-unsigned int samsung_rev(void)
-{
-	return samsung_cpu_rev;
-}
-EXPORT_SYMBOL(samsung_rev);
 
 void __init s3c64xx_init_cpu(void)
 {
@@ -34,15 +27,5 @@ void __init s3c64xx_init_cpu(void)
 		samsung_cpu_id = readl_relaxed(S3C_VA_SYS + 0xA1C);
 	}
 
-	samsung_cpu_rev = 0;
-
-	pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
-}
-
-void __init s5p_init_cpu(const void __iomem *cpuid_addr)
-{
-	samsung_cpu_id = readl_relaxed(cpuid_addr);
-	samsung_cpu_rev = samsung_cpu_id & 0xFF;
-
 	pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
 }
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/mach-s3c/cpu.h
index fadcddbea064..20ff98d05c53 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/mach-s3c/cpu.h
@@ -109,9 +109,6 @@ extern void s3c_init_cpu(unsigned long idcode,
 extern void s3c24xx_init_io(struct map_desc *mach_desc, int size);
 
 extern void s3c64xx_init_cpu(void);
-extern void s5p_init_cpu(const void __iomem *cpuid_addr);
-
-extern unsigned int samsung_rev(void);
 
 extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no);
 
@@ -126,15 +123,6 @@ extern struct syscore_ops s3c2412_pm_syscore_ops;
 extern struct syscore_ops s3c2416_pm_syscore_ops;
 extern struct syscore_ops s3c244x_pm_syscore_ops;
 
-/* system device subsystems */
-
-extern struct bus_type s3c2410_subsys;
-extern struct bus_type s3c2410a_subsys;
-extern struct bus_type s3c2412_subsys;
-extern struct bus_type s3c2416_subsys;
-extern struct bus_type s3c2440_subsys;
-extern struct bus_type s3c2442_subsys;
-extern struct bus_type s3c2443_subsys;
 extern struct bus_type s3c6410_subsys;
 
 #endif
diff --git a/arch/arm/mach-s3c24xx/cpufreq-utils.c b/arch/arm/mach-s3c/cpufreq-utils-s3c24xx.c
index 1a7f38d085dd..c1784d8facdf 100644
--- a/arch/arm/mach-s3c24xx/cpufreq-utils.c
+++ b/arch/arm/mach-s3c/cpufreq-utils-s3c24xx.c
@@ -12,12 +12,12 @@
 #include <linux/io.h>
 #include <linux/clk.h>
 
-#include <mach/map.h>
-#include <mach/regs-clock.h>
+#include "map.h"
+#include "regs-clock.h"
 
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
 
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 /**
  * s3c2410_cpufreq_setrefresh - set SDRAM refresh value
@@ -60,3 +60,35 @@ void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg)
 	if (!IS_ERR(cfg->mpll))
 		clk_set_rate(cfg->mpll, cfg->pll.frequency);
 }
+
+#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
+u32 s3c2440_read_camdivn(void)
+{
+	return __raw_readl(S3C2440_CAMDIVN);
+}
+
+void s3c2440_write_camdivn(u32 camdiv)
+{
+	__raw_writel(camdiv, S3C2440_CAMDIVN);
+}
+#endif
+
+u32 s3c24xx_read_clkdivn(void)
+{
+	return __raw_readl(S3C2410_CLKDIVN);
+}
+
+void s3c24xx_write_clkdivn(u32 clkdiv)
+{
+	__raw_writel(clkdiv, S3C2410_CLKDIVN);
+}
+
+u32 s3c24xx_read_mpllcon(void)
+{
+	return __raw_readl(S3C2410_MPLLCON);
+}
+
+void s3c24xx_write_locktime(u32 locktime)
+{
+	return __raw_writel(locktime, S3C2410_LOCKTIME);
+}
diff --git a/arch/arm/mach-s3c64xx/cpuidle.c b/arch/arm/mach-s3c/cpuidle-s3c64xx.c
index 0bac6f6413b0..b1c5f43d4922 100644
--- a/arch/arm/mach-s3c64xx/cpuidle.c
+++ b/arch/arm/mach-s3c/cpuidle-s3c64xx.c
@@ -13,11 +13,11 @@
 
 #include <asm/cpuidle.h>
 
-#include <plat/cpu.h>
-#include <mach/map.h>
+#include "cpu.h"
+#include "map.h"
 
-#include "regs-sys.h"
-#include "regs-syscon-power.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-syscon-power-s3c64xx.h"
 
 static int s3c64xx_enter_idle(struct cpuidle_device *dev,
 			      struct cpuidle_driver *drv,
diff --git a/arch/arm/mach-s3c64xx/crag6410.h b/arch/arm/mach-s3c/crag6410.h
index 00d9aa114aa7..f39ea2ca7a75 100644
--- a/arch/arm/mach-s3c64xx/crag6410.h
+++ b/arch/arm/mach-s3c/crag6410.h
@@ -8,7 +8,7 @@
 #ifndef MACH_CRAG6410_H
 #define MACH_CRAG6410_H
 
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
 
 #define GLENFARCLAS_PMIC_IRQ_BASE	IRQ_BOARD_START
 #define BANFF_PMIC_IRQ_BASE		(IRQ_BOARD_START + 64)
diff --git a/arch/arm/mach-s3c64xx/dev-audio.c b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
index e3c49b5d1355..fc2f077afd24 100644
--- a/arch/arm/mach-s3c64xx/dev-audio.c
+++ b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
@@ -11,13 +11,12 @@
 #include <linux/export.h>
 
 #include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/dma.h>
+#include "map.h"
 
-#include <plat/devs.h>
+#include "devs.h"
 #include <linux/platform_data/asoc-s3c.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 static int s3c64xx_i2s_cfg_gpio(struct platform_device *pdev)
 {
diff --git a/arch/arm/mach-s3c64xx/dev-backlight.c b/arch/arm/mach-s3c/dev-backlight-s3c64xx.c
index 09e6da305f60..65488b61e50c 100644
--- a/arch/arm/mach-s3c64xx/dev-backlight.c
+++ b/arch/arm/mach-s3c/dev-backlight-s3c64xx.c
@@ -11,10 +11,10 @@
 #include <linux/io.h>
 #include <linux/pwm_backlight.h>
 
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
+#include "devs.h"
+#include "gpio-cfg.h"
 
-#include "backlight.h"
+#include "backlight-s3c64xx.h"
 
 struct samsung_bl_drvdata {
 	struct platform_pwm_backlight_data plat_data;
diff --git a/arch/arm/mach-s3c64xx/dev-uart.c b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
index 5fb59ad30008..8288e8d6c092 100644
--- a/arch/arm/mach-s3c64xx/dev-uart.c
+++ b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
@@ -15,11 +15,10 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 #include <mach/irqs.h>
 
-#include <plat/devs.h>
+#include "devs.h"
 
 /* Serial port registrations */
 
diff --git a/arch/arm/plat-samsung/dev-uart.c b/arch/arm/mach-s3c/dev-uart.c
index 7476a5dbae77..3d1f7f2fd7c7 100644
--- a/arch/arm/plat-samsung/dev-uart.c
+++ b/arch/arm/mach-s3c/dev-uart.c
@@ -10,7 +10,7 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 
-#include <plat/devs.h>
+#include "devs.h"
 
 /* uart devices */
 
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/mach-s3c/devs.c
index 089a17687104..06dec64848f9 100644
--- a/arch/arm/plat-samsung/devs.c
+++ b/arch/arm/mach-s3c/devs.c
@@ -5,6 +5,7 @@
 //
 // Base Samsung platform device definitions
 
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -37,28 +38,32 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/dma.h>
 #include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/adc.h>
+#ifdef CONFIG_PLAT_S3C24XX
+#include "regs-s3c2443-clock.h"
+#endif /* CONFIG_PLAT_S3C24XX */
+
+#include "cpu.h"
+#include "devs.h"
+#include <linux/soc/samsung/s3c-adc.h>
 #include <linux/platform_data/ata-samsung_cf.h>
-#include <plat/fb.h>
-#include <plat/fb-s3c2410.h>
+#include "fb.h"
+#include <linux/platform_data/fb-s3c2410.h>
 #include <linux/platform_data/hwmon-s3c.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/keypad.h>
+#include "keypad.h"
 #include <linux/platform_data/mmc-s3cmci.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/pwm-core.h>
-#include <plat/sdhci.h>
+#include "pwm-core.h"
+#include "sdhci.h"
 #include <linux/platform_data/touchscreen-s3c2410.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
 #include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/usb-phy.h>
-#include <plat/regs-spi.h>
+#include "usb-phy.h"
 #include <linux/platform_data/asoc-s3c.h>
 #include <linux/platform_data/spi-s3c64xx.h>
 
@@ -833,16 +838,42 @@ struct platform_device s3c_device_rtc = {
 /* SDI */
 
 #ifdef CONFIG_PLAT_S3C24XX
+void s3c24xx_mci_def_set_power(unsigned char power_mode, unsigned short vdd)
+{
+	switch (power_mode) {
+	case MMC_POWER_ON:
+	case MMC_POWER_UP:
+		/* Configure GPE5...GPE10 pins in SD mode */
+		s3c_gpio_cfgall_range(S3C2410_GPE(5), 6, S3C_GPIO_SFN(2),
+				      S3C_GPIO_PULL_NONE);
+		break;
+
+	case MMC_POWER_OFF:
+	default:
+		gpio_direction_output(S3C2410_GPE(5), 0);
+		break;
+	}
+}
+
 static struct resource s3c_sdi_resource[] = {
 	[0] = DEFINE_RES_MEM(S3C24XX_PA_SDI, S3C24XX_SZ_SDI),
 	[1] = DEFINE_RES_IRQ(IRQ_SDI),
 };
 
+static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
+	/* This is currently here to avoid a number of if (host->pdata)
+	 * checks. Any zero fields to ensure reasonable defaults are picked. */
+	.no_wprotect = 1,
+	.no_detect = 1,
+	.set_power = s3c24xx_mci_def_set_power,
+};
+
 struct platform_device s3c_device_sdi = {
 	.name		= "s3c2410-sdi",
 	.id		= -1,
 	.num_resources	= ARRAY_SIZE(s3c_sdi_resource),
 	.resource	= s3c_sdi_resource,
+	.dev.platform_data = &s3cmci_def_pdata,
 };
 
 void __init s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata)
@@ -1038,6 +1069,8 @@ struct platform_device s3c_device_usb_hsudc = {
 void __init s3c24xx_hsudc_set_platdata(struct s3c24xx_hsudc_platdata *pd)
 {
 	s3c_set_platdata(pd, sizeof(*pd), &s3c_device_usb_hsudc);
+	pd->phy_init = s3c_hsudc_init_phy;
+	pd->phy_uninit = s3c_hsudc_uninit_phy;
 }
 #endif /* CONFIG_PLAT_S3C24XX */
 
diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/mach-s3c/devs.h
index 02b0c5750572..02b0c5750572 100644
--- a/arch/arm/plat-samsung/include/plat/devs.h
+++ b/arch/arm/mach-s3c/devs.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/dma.h b/arch/arm/mach-s3c/dma-s3c24xx.h
index 25fc9c258fc1..25fc9c258fc1 100644
--- a/arch/arm/mach-s3c24xx/include/mach/dma.h
+++ b/arch/arm/mach-s3c/dma-s3c24xx.h
diff --git a/arch/arm/mach-s3c64xx/include/mach/dma.h b/arch/arm/mach-s3c/dma-s3c64xx.h
index 40ca8de21096..40ca8de21096 100644
--- a/arch/arm/mach-s3c64xx/include/mach/dma.h
+++ b/arch/arm/mach-s3c/dma-s3c64xx.h
diff --git a/arch/arm/mach-s3c/dma.h b/arch/arm/mach-s3c/dma.h
new file mode 100644
index 000000000000..59a4578c5f00
--- /dev/null
+++ b/arch/arm/mach-s3c/dma.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "dma-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "dma-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/fb-core.h b/arch/arm/mach-s3c/fb-core-s3c24xx.h
index 1821e820262c..0e07f3ba4aef 100644
--- a/arch/arm/mach-s3c24xx/fb-core.h
+++ b/arch/arm/mach-s3c/fb-core-s3c24xx.h
@@ -5,8 +5,8 @@
  *
  * Samsung framebuffer driver core functions
  */
-#ifndef __ASM_PLAT_FB_CORE_H
-#define __ASM_PLAT_FB_CORE_H __FILE__
+#ifndef __ASM_PLAT_FB_CORE_S3C24XX_H
+#define __ASM_PLAT_FB_CORE_S3C24XX_H __FILE__
 
 /*
  * These functions are only for use with the core support code, such as
@@ -21,4 +21,4 @@ static inline void s3c_fb_setname(char *name)
 #endif
 }
 
-#endif /* __ASM_PLAT_FB_CORE_H */
+#endif /* __ASM_PLAT_FB_CORE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/mach-s3c/fb.h
index 615d381ae32e..615d381ae32e 100644
--- a/arch/arm/plat-samsung/include/plat/fb.h
+++ b/arch/arm/mach-s3c/fb.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h b/arch/arm/mach-s3c/gpio-cfg-helpers.h
index db0c56f5ca15..db0c56f5ca15 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
+++ b/arch/arm/mach-s3c/gpio-cfg-helpers.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/mach-s3c/gpio-cfg.h
index 469c220e092b..469c220e092b 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg.h
+++ b/arch/arm/mach-s3c/gpio-cfg.h
diff --git a/arch/arm/plat-samsung/include/plat/gpio-core.h b/arch/arm/mach-s3c/gpio-core.h
index c0bfceb88340..b361c8c0d669 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-core.h
+++ b/arch/arm/mach-s3c/gpio-core.h
@@ -11,7 +11,7 @@
 #define __PLAT_SAMSUNG_GPIO_CORE_H
 
 /* Bring in machine-local definitions, especially S3C_GPIO_END */
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
 #include <linux/gpio/driver.h>
 
 #define GPIOCON_OFF	(0x00)
diff --git a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung-s3c24xx.h
index 2ad22b2d459b..c29fdc95f883 100644
--- a/arch/arm/mach-s3c24xx/include/mach/gpio-samsung.h
+++ b/arch/arm/mach-s3c/gpio-samsung-s3c24xx.h
@@ -14,6 +14,8 @@
 #ifndef GPIO_SAMSUNG_S3C24XX_H
 #define GPIO_SAMSUNG_S3C24XX_H
 
+#include "map.h"
+
 /*
  * GPIO sizes for various SoCs:
  *
diff --git a/arch/arm/mach-s3c64xx/include/mach/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung-s3c64xx.h
index 8ed144a0d474..8ed144a0d474 100644
--- a/arch/arm/mach-s3c64xx/include/mach/gpio-samsung.h
+++ b/arch/arm/mach-s3c/gpio-samsung-s3c64xx.h
diff --git a/arch/arm/plat-samsung/gpio-samsung.c b/arch/arm/mach-s3c/gpio-samsung.c
index 8955fd675265..76ef415789f2 100644
--- a/arch/arm/plat-samsung/gpio-samsung.c
+++ b/arch/arm/mach-s3c/gpio-samsung.c
@@ -27,15 +27,15 @@
 #include <asm/irq.h>
 
 #include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-
-#include <plat/cpu.h>
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/pm.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include "cpu.h"
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "pm.h"
 
 int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
 				unsigned int off, samsung_gpio_pull_t pull)
diff --git a/arch/arm/mach-s3c/gpio-samsung.h b/arch/arm/mach-s3c/gpio-samsung.h
new file mode 100644
index 000000000000..02f6f4a96862
--- /dev/null
+++ b/arch/arm/mach-s3c/gpio-samsung.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "gpio-samsung-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "gpio-samsung-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/gta02.h b/arch/arm/mach-s3c/gta02.h
index d5610ba829a4..043ae382bfc5 100644
--- a/arch/arm/mach-s3c24xx/gta02.h
+++ b/arch/arm/mach-s3c/gta02.h
@@ -6,7 +6,7 @@
 #ifndef __MACH_S3C24XX_GTA02_H
 #define __MACH_S3C24XX_GTA02_H __FILE__
 
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
 
 #define GTA02_GPIO_AUX_LED	S3C2410_GPB(2)
 #define GTA02_GPIO_USB_PULLUP	S3C2410_GPB(9)
diff --git a/arch/arm/mach-s3c24xx/h1940-bluetooth.c b/arch/arm/mach-s3c/h1940-bluetooth.c
index 186b5321658e..59edcf8a620d 100644
--- a/arch/arm/mach-s3c24xx/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c/h1940-bluetooth.c
@@ -13,10 +13,9 @@
 #include <linux/gpio.h>
 #include <linux/rfkill.h>
 
-#include <plat/gpio-cfg.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
 #include "h1940.h"
 
diff --git a/arch/arm/mach-s3c24xx/h1940.h b/arch/arm/mach-s3c/h1940.h
index 5dfe9d10cd15..5dfe9d10cd15 100644
--- a/arch/arm/mach-s3c24xx/h1940.h
+++ b/arch/arm/mach-s3c/h1940.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/hardware.h b/arch/arm/mach-s3c/hardware-s3c24xx.h
index f28ac6c78d82..33b37467d05f 100644
--- a/arch/arm/mach-s3c24xx/include/mach/hardware.h
+++ b/arch/arm/mach-s3c/hardware-s3c24xx.h
@@ -6,16 +6,9 @@
  * S3C2410 - hardware
  */
 
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#ifndef __ASSEMBLY__
+#ifndef __ASM_ARCH_HARDWARE_S3C24XX_H
+#define __ASM_ARCH_HARDWARE_S3C24XX_H
 
 extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
 
-#endif /* __ASSEMBLY__ */
-
-#include <linux/sizes.h>
-#include <mach/map.h>
-
-#endif /* __ASM_ARCH_HARDWARE_H */
+#endif /* __ASM_ARCH_HARDWARE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/iic-core.h b/arch/arm/mach-s3c/iic-core.h
index c5cfd5af3874..c5cfd5af3874 100644
--- a/arch/arm/plat-samsung/include/plat/iic-core.h
+++ b/arch/arm/mach-s3c/iic-core.h
diff --git a/arch/arm/mach-s3c/include/mach/io-s3c24xx.h b/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
new file mode 100644
index 000000000000..738b775d3336
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-s3c2410/include/mach/io.h
+ *  from arch/arm/mach-rpc/include/mach/io.h
+ *
+ * Copyright (C) 1997 Russell King
+ *	     (C) 2003 Simtec Electronics
+*/
+
+#ifndef __ASM_ARM_ARCH_IO_S3C24XX_H
+#define __ASM_ARM_ARCH_IO_S3C24XX_H
+
+#include <mach/map-base.h>
+
+/*
+ * ISA style IO, for each machine to sort out mappings for,
+ * if it implements it. We reserve two 16M regions for ISA,
+ * so the PC/104 can use separate addresses for 8-bit and
+ * 16-bit port I/O.
+ */
+#define PCIO_BASE		S3C_ADDR(0x02000000)
+#define IO_SPACE_LIMIT		0x00ffffff
+#define S3C24XX_VA_ISA_WORD	(PCIO_BASE)
+#define S3C24XX_VA_ISA_BYTE	(PCIO_BASE + 0x01000000)
+
+#ifdef CONFIG_ISA
+
+#define inb(p)		readb(S3C24XX_VA_ISA_BYTE + (p))
+#define inw(p)		readw(S3C24XX_VA_ISA_WORD + (p))
+#define inl(p)		readl(S3C24XX_VA_ISA_WORD + (p))
+
+#define outb(v,p)	writeb((v), S3C24XX_VA_ISA_BYTE + (p))
+#define outw(v,p)	writew((v), S3C24XX_VA_ISA_WORD + (p))
+#define outl(v,p)	writel((v), S3C24XX_VA_ISA_WORD + (p))
+
+#define insb(p,d,l)	readsb(S3C24XX_VA_ISA_BYTE + (p),d,l)
+#define insw(p,d,l)	readsw(S3C24XX_VA_ISA_WORD + (p),d,l)
+#define insl(p,d,l)	readsl(S3C24XX_VA_ISA_WORD + (p),d,l)
+
+#define outsb(p,d,l)	writesb(S3C24XX_VA_ISA_BYTE + (p),d,l)
+#define outsw(p,d,l)	writesw(S3C24XX_VA_ISA_WORD + (p),d,l)
+#define outsl(p,d,l)	writesl(S3C24XX_VA_ISA_WORD + (p),d,l)
+
+#else
+
+#define __io(x) (PCIO_BASE + (x))
+
+#endif
+
+#endif
diff --git a/arch/arm/mach-s3c/include/mach/io.h b/arch/arm/mach-s3c/include/mach/io.h
new file mode 100644
index 000000000000..30a0135708dc
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/io.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "io-s3c24xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h
index aaf3bae08b52..aaf3bae08b52 100644
--- a/arch/arm/mach-s3c24xx/include/mach/irqs.h
+++ b/arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h
diff --git a/arch/arm/mach-s3c64xx/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h
index c244e480e6b3..c244e480e6b3 100644
--- a/arch/arm/mach-s3c64xx/include/mach/irqs.h
+++ b/arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h
diff --git a/arch/arm/mach-s3c/include/mach/irqs.h b/arch/arm/mach-s3c/include/mach/irqs.h
new file mode 100644
index 000000000000..0bff1c1c8eb0
--- /dev/null
+++ b/arch/arm/mach-s3c/include/mach/irqs.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "irqs-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "irqs-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/map-base.h b/arch/arm/mach-s3c/include/mach/map-base.h
index 34b39ded0e2e..34b39ded0e2e 100644
--- a/arch/arm/plat-samsung/include/plat/map-base.h
+++ b/arch/arm/mach-s3c/include/mach/map-base.h
diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/mach-s3c/init.c
index e9acf02ef3c3..9d92f03e9bc1 100644
--- a/arch/arm/plat-samsung/init.c
+++ b/arch/arm/mach-s3c/init.c
@@ -23,8 +23,8 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
+#include "cpu.h"
+#include "devs.h"
 
 static struct cpu_table *cpu;
 
diff --git a/arch/arm/mach-s3c24xx/iotiming-s3c2410.c b/arch/arm/mach-s3c/iotiming-s3c2410.c
index 9f90aaf70bf3..28d9f473e24a 100644
--- a/arch/arm/mach-s3c24xx/iotiming-s3c2410.c
+++ b/arch/arm/mach-s3c/iotiming-s3c2410.c
@@ -14,12 +14,12 @@
 #include <linux/io.h>
 #include <linux/slab.h>
 
-#include <mach/map.h>
-#include <mach/regs-clock.h>
+#include "map.h"
+#include "regs-clock.h"
 
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
 
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 #define print_ns(x) ((x) / 10), ((x) % 10)
 
@@ -129,7 +129,7 @@ static unsigned int calc_0124(unsigned int cyc, unsigned long hclk_tns,
 	return 0;
 }
 
-int calc_tacp(unsigned int cyc, unsigned long hclk, unsigned long *v)
+static int calc_tacp(unsigned int cyc, unsigned long hclk, unsigned long *v)
 {
 	/* Currently no support for Tacp calculations. */
 	return 0;
@@ -288,8 +288,8 @@ static unsigned int get_0124(unsigned long hclk_tns,
  * Given the BANKCON setting in @bt and the current frequency settings
  * in @cfg, update the cycle timing information.
  */
-void s3c2410_iotiming_getbank(struct s3c_cpufreq_config *cfg,
-			      struct s3c2410_iobank_timing *bt)
+static void s3c2410_iotiming_getbank(struct s3c_cpufreq_config *cfg,
+				     struct s3c2410_iobank_timing *bt)
 {
 	unsigned long bankcon = bt->bankcon;
 	unsigned long hclk = cfg->freq.hclk_tns;
diff --git a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c b/arch/arm/mach-s3c/iotiming-s3c2412.c
index 59356d10fbcf..003f89c4dc53 100644
--- a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c
+++ b/arch/arm/mach-s3c/iotiming-s3c2412.c
@@ -23,10 +23,10 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
 
-#include <mach/s3c2412.h>
+#include "s3c2412.h"
 
 #define print_ns(x) ((x) / 10), ((x) % 10)
 
diff --git a/arch/arm/mach-s3c24xx/irq-pm.c b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
index e0131b16a4af..4d5e28312d91 100644
--- a/arch/arm/mach-s3c24xx/irq-pm.c
+++ b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
@@ -13,14 +13,14 @@
 #include <linux/syscore_ops.h>
 #include <linux/io.h>
 
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
-
-#include <mach/regs-irq.h>
-#include <mach/regs-gpio.h>
-#include <mach/pm-core.h>
+#include "cpu.h"
+#include "pm.h"
+#include <mach/map-base.h>
+#include "map-s3c.h"
+
+#include "regs-irq.h"
+#include "regs-gpio.h"
+#include "pm-core.h"
 
 #include <asm/irq.h>
 
diff --git a/arch/arm/mach-s3c64xx/irq-pm.c b/arch/arm/mach-s3c/irq-pm-s3c64xx.c
index 31b221190479..4a1e935bada1 100644
--- a/arch/arm/mach-s3c64xx/irq-pm.c
+++ b/arch/arm/mach-s3c/irq-pm-s3c64xx.c
@@ -20,11 +20,11 @@
 #include <linux/io.h>
 #include <linux/of.h>
 
-#include <mach/map.h>
+#include "map.h"
 
-#include <mach/regs-gpio.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "regs-gpio.h"
+#include "cpu.h"
+#include "pm.h"
 
 /* We handled all the IRQ types in this code, to save having to make several
  * small files to handle each different type separately. Having the EINT_GRP
diff --git a/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c b/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c
new file mode 100644
index 000000000000..84cf86376ded
--- /dev/null
+++ b/arch/arm/mach-s3c/irq-s3c24xx-fiq-exports.c
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/stddef.h>
+#include <linux/export.h>
+#include <linux/spi/s3c24xx-fiq.h>
+
+EXPORT_SYMBOL(s3c24xx_spi_fiq_rx);
+EXPORT_SYMBOL(s3c24xx_spi_fiq_txrx);
+EXPORT_SYMBOL(s3c24xx_spi_fiq_tx);
diff --git a/arch/arm/mach-s3c/irq-s3c24xx-fiq.S b/arch/arm/mach-s3c/irq-s3c24xx-fiq.S
new file mode 100644
index 000000000000..b54cbd012241
--- /dev/null
+++ b/arch/arm/mach-s3c/irq-s3c24xx-fiq.S
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* linux/drivers/spi/spi_s3c24xx_fiq.S
+ *
+ * Copyright 2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX SPI - FIQ pseudo-DMA transfer code
+*/
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+#include "map.h"
+#include "regs-irq.h"
+
+#include <linux/spi/s3c24xx-fiq.h>
+
+#define S3C2410_SPTDAT           (0x10)
+#define S3C2410_SPRDAT           (0x14)
+
+	.text
+
+	@ entry to these routines is as follows, with the register names
+	@ defined in fiq.h so that they can be shared with the C files which
+	@ setup the calling registers.
+	@
+	@ fiq_rirq	The base of the IRQ registers to find S3C2410_SRCPND
+	@ fiq_rtmp	Temporary register to hold tx/rx data
+	@ fiq_rspi	The base of the SPI register block
+	@ fiq_rtx	The tx buffer pointer
+	@ fiq_rrx	The rx buffer pointer
+	@ fiq_rcount	The number of bytes to move
+
+	@ each entry starts with a word entry of how long it is
+	@ and an offset to the irq acknowledgment word
+
+ENTRY(s3c24xx_spi_fiq_rx)
+s3c24xx_spi_fix_rx:
+	.word	fiq_rx_end - fiq_rx_start
+	.word	fiq_rx_irq_ack - fiq_rx_start
+fiq_rx_start:
+	ldr	fiq_rtmp, fiq_rx_irq_ack
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+	ldrb	fiq_rtmp, [ fiq_rspi, #  S3C2410_SPRDAT ]
+	strb	fiq_rtmp, [ fiq_rrx ], #1
+
+	mov	fiq_rtmp, #0xff
+	strb	fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+	subs	fiq_rcount, fiq_rcount, #1
+	subnes	pc, lr, #4		@@ return, still have work to do
+
+	@@ set IRQ controller so that next op will trigger IRQ
+	mov	fiq_rtmp, #0
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD  - S3C24XX_VA_IRQ ]
+	subs	pc, lr, #4
+
+fiq_rx_irq_ack:
+	.word	0
+fiq_rx_end:
+
+ENTRY(s3c24xx_spi_fiq_txrx)
+s3c24xx_spi_fiq_txrx:
+	.word	fiq_txrx_end - fiq_txrx_start
+	.word	fiq_txrx_irq_ack - fiq_txrx_start
+fiq_txrx_start:
+
+	ldrb	fiq_rtmp, [ fiq_rspi, #  S3C2410_SPRDAT ]
+	strb	fiq_rtmp, [ fiq_rrx ], #1
+
+	ldr	fiq_rtmp, fiq_txrx_irq_ack
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+	ldrb	fiq_rtmp, [ fiq_rtx ], #1
+	strb	fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+	subs	fiq_rcount, fiq_rcount, #1
+	subnes	pc, lr, #4		@@ return, still have work to do
+
+	mov	fiq_rtmp, #0
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD  - S3C24XX_VA_IRQ ]
+	subs	pc, lr, #4
+
+fiq_txrx_irq_ack:
+	.word	0
+
+fiq_txrx_end:
+
+ENTRY(s3c24xx_spi_fiq_tx)
+s3c24xx_spi_fix_tx:
+	.word	fiq_tx_end - fiq_tx_start
+	.word	fiq_tx_irq_ack - fiq_tx_start
+fiq_tx_start:
+	ldrb	fiq_rtmp, [ fiq_rspi, #  S3C2410_SPRDAT ]
+
+	ldr	fiq_rtmp, fiq_tx_irq_ack
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+	ldrb	fiq_rtmp, [ fiq_rtx ], #1
+	strb	fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+	subs	fiq_rcount, fiq_rcount, #1
+	subnes	pc, lr, #4		@@ return, still have work to do
+
+	mov	fiq_rtmp, #0
+	str	fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD  - S3C24XX_VA_IRQ ]
+	subs	pc, lr, #4
+
+fiq_tx_irq_ack:
+	.word	0
+
+fiq_tx_end:
+
+	.end
diff --git a/arch/arm/mach-s3c/irq-s3c24xx.c b/arch/arm/mach-s3c/irq-s3c24xx.c
new file mode 100644
index 000000000000..79b5f19af7a5
--- /dev/null
+++ b/arch/arm/mach-s3c/irq-s3c24xx.c
@@ -0,0 +1,1337 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * S3C24XX IRQ handling
+ *
+ * Copyright (c) 2003-2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2012 Heiko Stuebner <heiko@sntech.de>
+*/
+
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+
+#include <asm/exception.h>
+#include <asm/mach/irq.h>
+
+#include <mach/irqs.h>
+#include "regs-irq.h"
+#include "regs-gpio.h"
+
+#include "cpu.h"
+#include "regs-irqtype.h"
+#include "pm.h"
+
+#define S3C_IRQTYPE_NONE	0
+#define S3C_IRQTYPE_EINT	1
+#define S3C_IRQTYPE_EDGE	2
+#define S3C_IRQTYPE_LEVEL	3
+
+struct s3c_irq_data {
+	unsigned int type;
+	unsigned long offset;
+	unsigned long parent_irq;
+
+	/* data gets filled during init */
+	struct s3c_irq_intc *intc;
+	unsigned long sub_bits;
+	struct s3c_irq_intc *sub_intc;
+};
+
+/*
+ * Structure holding the controller data
+ * @reg_pending		register holding pending irqs
+ * @reg_intpnd		special register intpnd in main intc
+ * @reg_mask		mask register
+ * @domain		irq_domain of the controller
+ * @parent		parent controller for ext and sub irqs
+ * @irqs		irq-data, always s3c_irq_data[32]
+ */
+struct s3c_irq_intc {
+	void __iomem		*reg_pending;
+	void __iomem		*reg_intpnd;
+	void __iomem		*reg_mask;
+	struct irq_domain	*domain;
+	struct s3c_irq_intc	*parent;
+	struct s3c_irq_data	*irqs;
+};
+
+/*
+ * Array holding pointers to the global controller structs
+ * [0] ... main_intc
+ * [1] ... sub_intc
+ * [2] ... main_intc2 on s3c2416
+ */
+static struct s3c_irq_intc *s3c_intc[3];
+
+static void s3c_irq_mask(struct irq_data *data)
+{
+	struct s3c_irq_data *irq_data = irq_data_get_irq_chip_data(data);
+	struct s3c_irq_intc *intc = irq_data->intc;
+	struct s3c_irq_intc *parent_intc = intc->parent;
+	struct s3c_irq_data *parent_data;
+	unsigned long mask;
+	unsigned int irqno;
+
+	mask = readl_relaxed(intc->reg_mask);
+	mask |= (1UL << irq_data->offset);
+	writel_relaxed(mask, intc->reg_mask);
+
+	if (parent_intc) {
+		parent_data = &parent_intc->irqs[irq_data->parent_irq];
+
+		/* check to see if we need to mask the parent IRQ
+		 * The parent_irq is always in main_intc, so the hwirq
+		 * for find_mapping does not need an offset in any case.
+		 */
+		if ((mask & parent_data->sub_bits) == parent_data->sub_bits) {
+			irqno = irq_find_mapping(parent_intc->domain,
+					 irq_data->parent_irq);
+			s3c_irq_mask(irq_get_irq_data(irqno));
+		}
+	}
+}
+
+static void s3c_irq_unmask(struct irq_data *data)
+{
+	struct s3c_irq_data *irq_data = irq_data_get_irq_chip_data(data);
+	struct s3c_irq_intc *intc = irq_data->intc;
+	struct s3c_irq_intc *parent_intc = intc->parent;
+	unsigned long mask;
+	unsigned int irqno;
+
+	mask = readl_relaxed(intc->reg_mask);
+	mask &= ~(1UL << irq_data->offset);
+	writel_relaxed(mask, intc->reg_mask);
+
+	if (parent_intc) {
+		irqno = irq_find_mapping(parent_intc->domain,
+					 irq_data->parent_irq);
+		s3c_irq_unmask(irq_get_irq_data(irqno));
+	}
+}
+
+static inline void s3c_irq_ack(struct irq_data *data)
+{
+	struct s3c_irq_data *irq_data = irq_data_get_irq_chip_data(data);
+	struct s3c_irq_intc *intc = irq_data->intc;
+	unsigned long bitval = 1UL << irq_data->offset;
+
+	writel_relaxed(bitval, intc->reg_pending);
+	if (intc->reg_intpnd)
+		writel_relaxed(bitval, intc->reg_intpnd);
+}
+
+static int s3c_irq_type(struct irq_data *data, unsigned int type)
+{
+	switch (type) {
+	case IRQ_TYPE_NONE:
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+	case IRQ_TYPE_EDGE_FALLING:
+	case IRQ_TYPE_EDGE_BOTH:
+		irq_set_handler(data->irq, handle_edge_irq);
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+	case IRQ_TYPE_LEVEL_HIGH:
+		irq_set_handler(data->irq, handle_level_irq);
+		break;
+	default:
+		pr_err("No such irq type %d\n", type);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int s3c_irqext_type_set(void __iomem *gpcon_reg,
+			       void __iomem *extint_reg,
+			       unsigned long gpcon_offset,
+			       unsigned long extint_offset,
+			       unsigned int type)
+{
+	unsigned long newvalue = 0, value;
+
+	/* Set the GPIO to external interrupt mode */
+	value = readl_relaxed(gpcon_reg);
+	value = (value & ~(3 << gpcon_offset)) | (0x02 << gpcon_offset);
+	writel_relaxed(value, gpcon_reg);
+
+	/* Set the external interrupt to pointed trigger type */
+	switch (type)
+	{
+		case IRQ_TYPE_NONE:
+			pr_warn("No edge setting!\n");
+			break;
+
+		case IRQ_TYPE_EDGE_RISING:
+			newvalue = S3C2410_EXTINT_RISEEDGE;
+			break;
+
+		case IRQ_TYPE_EDGE_FALLING:
+			newvalue = S3C2410_EXTINT_FALLEDGE;
+			break;
+
+		case IRQ_TYPE_EDGE_BOTH:
+			newvalue = S3C2410_EXTINT_BOTHEDGE;
+			break;
+
+		case IRQ_TYPE_LEVEL_LOW:
+			newvalue = S3C2410_EXTINT_LOWLEV;
+			break;
+
+		case IRQ_TYPE_LEVEL_HIGH:
+			newvalue = S3C2410_EXTINT_HILEV;
+			break;
+
+		default:
+			pr_err("No such irq type %d\n", type);
+			return -EINVAL;
+	}
+
+	value = readl_relaxed(extint_reg);
+	value = (value & ~(7 << extint_offset)) | (newvalue << extint_offset);
+	writel_relaxed(value, extint_reg);
+
+	return 0;
+}
+
+static int s3c_irqext_type(struct irq_data *data, unsigned int type)
+{
+	void __iomem *extint_reg;
+	void __iomem *gpcon_reg;
+	unsigned long gpcon_offset, extint_offset;
+
+	if ((data->hwirq >= 4) && (data->hwirq <= 7)) {
+		gpcon_reg = S3C2410_GPFCON;
+		extint_reg = S3C24XX_EXTINT0;
+		gpcon_offset = (data->hwirq) * 2;
+		extint_offset = (data->hwirq) * 4;
+	} else if ((data->hwirq >= 8) && (data->hwirq <= 15)) {
+		gpcon_reg = S3C2410_GPGCON;
+		extint_reg = S3C24XX_EXTINT1;
+		gpcon_offset = (data->hwirq - 8) * 2;
+		extint_offset = (data->hwirq - 8) * 4;
+	} else if ((data->hwirq >= 16) && (data->hwirq <= 23)) {
+		gpcon_reg = S3C2410_GPGCON;
+		extint_reg = S3C24XX_EXTINT2;
+		gpcon_offset = (data->hwirq - 8) * 2;
+		extint_offset = (data->hwirq - 16) * 4;
+	} else {
+		return -EINVAL;
+	}
+
+	return s3c_irqext_type_set(gpcon_reg, extint_reg, gpcon_offset,
+				   extint_offset, type);
+}
+
+static int s3c_irqext0_type(struct irq_data *data, unsigned int type)
+{
+	void __iomem *extint_reg;
+	void __iomem *gpcon_reg;
+	unsigned long gpcon_offset, extint_offset;
+
+	if (data->hwirq <= 3) {
+		gpcon_reg = S3C2410_GPFCON;
+		extint_reg = S3C24XX_EXTINT0;
+		gpcon_offset = (data->hwirq) * 2;
+		extint_offset = (data->hwirq) * 4;
+	} else {
+		return -EINVAL;
+	}
+
+	return s3c_irqext_type_set(gpcon_reg, extint_reg, gpcon_offset,
+				   extint_offset, type);
+}
+
+static struct irq_chip s3c_irq_chip = {
+	.name		= "s3c",
+	.irq_ack	= s3c_irq_ack,
+	.irq_mask	= s3c_irq_mask,
+	.irq_unmask	= s3c_irq_unmask,
+	.irq_set_type	= s3c_irq_type,
+	.irq_set_wake	= s3c_irq_wake
+};
+
+static struct irq_chip s3c_irq_level_chip = {
+	.name		= "s3c-level",
+	.irq_mask	= s3c_irq_mask,
+	.irq_unmask	= s3c_irq_unmask,
+	.irq_ack	= s3c_irq_ack,
+	.irq_set_type	= s3c_irq_type,
+};
+
+static struct irq_chip s3c_irqext_chip = {
+	.name		= "s3c-ext",
+	.irq_mask	= s3c_irq_mask,
+	.irq_unmask	= s3c_irq_unmask,
+	.irq_ack	= s3c_irq_ack,
+	.irq_set_type	= s3c_irqext_type,
+	.irq_set_wake	= s3c_irqext_wake
+};
+
+static struct irq_chip s3c_irq_eint0t4 = {
+	.name		= "s3c-ext0",
+	.irq_ack	= s3c_irq_ack,
+	.irq_mask	= s3c_irq_mask,
+	.irq_unmask	= s3c_irq_unmask,
+	.irq_set_wake	= s3c_irq_wake,
+	.irq_set_type	= s3c_irqext0_type,
+};
+
+static void s3c_irq_demux(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct s3c_irq_data *irq_data = irq_desc_get_chip_data(desc);
+	struct s3c_irq_intc *intc = irq_data->intc;
+	struct s3c_irq_intc *sub_intc = irq_data->sub_intc;
+	unsigned int n, offset, irq;
+	unsigned long src, msk;
+
+	/* we're using individual domains for the non-dt case
+	 * and one big domain for the dt case where the subintc
+	 * starts at hwirq number 32.
+	 */
+	offset = irq_domain_get_of_node(intc->domain) ? 32 : 0;
+
+	chained_irq_enter(chip, desc);
+
+	src = readl_relaxed(sub_intc->reg_pending);
+	msk = readl_relaxed(sub_intc->reg_mask);
+
+	src &= ~msk;
+	src &= irq_data->sub_bits;
+
+	while (src) {
+		n = __ffs(src);
+		src &= ~(1 << n);
+		irq = irq_find_mapping(sub_intc->domain, offset + n);
+		generic_handle_irq(irq);
+	}
+
+	chained_irq_exit(chip, desc);
+}
+
+static inline int s3c24xx_handle_intc(struct s3c_irq_intc *intc,
+				      struct pt_regs *regs, int intc_offset)
+{
+	int pnd;
+	int offset;
+
+	pnd = readl_relaxed(intc->reg_intpnd);
+	if (!pnd)
+		return false;
+
+	/* non-dt machines use individual domains */
+	if (!irq_domain_get_of_node(intc->domain))
+		intc_offset = 0;
+
+	/* We have a problem that the INTOFFSET register does not always
+	 * show one interrupt. Occasionally we get two interrupts through
+	 * the prioritiser, and this causes the INTOFFSET register to show
+	 * what looks like the logical-or of the two interrupt numbers.
+	 *
+	 * Thanks to Klaus, Shannon, et al for helping to debug this problem
+	 */
+	offset = readl_relaxed(intc->reg_intpnd + 4);
+
+	/* Find the bit manually, when the offset is wrong.
+	 * The pending register only ever contains the one bit of the next
+	 * interrupt to handle.
+	 */
+	if (!(pnd & (1 << offset)))
+		offset =  __ffs(pnd);
+
+	handle_domain_irq(intc->domain, intc_offset + offset, regs);
+	return true;
+}
+
+asmlinkage void __exception_irq_entry s3c24xx_handle_irq(struct pt_regs *regs)
+{
+	do {
+		if (likely(s3c_intc[0]))
+			if (s3c24xx_handle_intc(s3c_intc[0], regs, 0))
+				continue;
+
+		if (s3c_intc[2])
+			if (s3c24xx_handle_intc(s3c_intc[2], regs, 64))
+				continue;
+
+		break;
+	} while (1);
+}
+
+#ifdef CONFIG_FIQ
+/**
+ * s3c24xx_set_fiq - set the FIQ routing
+ * @irq: IRQ number to route to FIQ on processor.
+ * @ack_ptr: pointer to a location for storing the bit mask
+ * @on: Whether to route @irq to the FIQ, or to remove the FIQ routing.
+ *
+ * Change the state of the IRQ to FIQ routing depending on @irq and @on. If
+ * @on is true, the @irq is checked to see if it can be routed and the
+ * interrupt controller updated to route the IRQ. If @on is false, the FIQ
+ * routing is cleared, regardless of which @irq is specified.
+ *
+ * returns the mask value for the register.
+ */
+int s3c24xx_set_fiq(unsigned int irq, u32 *ack_ptr, bool on)
+{
+	u32 intmod;
+	unsigned offs;
+
+	if (on) {
+		offs = irq - FIQ_START;
+		if (offs > 31)
+			return 0;
+
+		intmod = 1 << offs;
+	} else {
+		intmod = 0;
+	}
+
+	if (ack_ptr)
+		*ack_ptr = intmod;
+	writel_relaxed(intmod, S3C2410_INTMOD);
+
+	return intmod;
+}
+
+EXPORT_SYMBOL_GPL(s3c24xx_set_fiq);
+#endif
+
+static int s3c24xx_irq_map(struct irq_domain *h, unsigned int virq,
+							irq_hw_number_t hw)
+{
+	struct s3c_irq_intc *intc = h->host_data;
+	struct s3c_irq_data *irq_data = &intc->irqs[hw];
+	struct s3c_irq_intc *parent_intc;
+	struct s3c_irq_data *parent_irq_data;
+	unsigned int irqno;
+
+	/* attach controller pointer to irq_data */
+	irq_data->intc = intc;
+	irq_data->offset = hw;
+
+	parent_intc = intc->parent;
+
+	/* set handler and flags */
+	switch (irq_data->type) {
+	case S3C_IRQTYPE_NONE:
+		return 0;
+	case S3C_IRQTYPE_EINT:
+		/* On the S3C2412, the EINT0to3 have a parent irq
+		 * but need the s3c_irq_eint0t4 chip
+		 */
+		if (parent_intc && (!soc_is_s3c2412() || hw >= 4))
+			irq_set_chip_and_handler(virq, &s3c_irqext_chip,
+						 handle_edge_irq);
+		else
+			irq_set_chip_and_handler(virq, &s3c_irq_eint0t4,
+						 handle_edge_irq);
+		break;
+	case S3C_IRQTYPE_EDGE:
+		if (parent_intc || intc->reg_pending == S3C2416_SRCPND2)
+			irq_set_chip_and_handler(virq, &s3c_irq_level_chip,
+						 handle_edge_irq);
+		else
+			irq_set_chip_and_handler(virq, &s3c_irq_chip,
+						 handle_edge_irq);
+		break;
+	case S3C_IRQTYPE_LEVEL:
+		if (parent_intc)
+			irq_set_chip_and_handler(virq, &s3c_irq_level_chip,
+						 handle_level_irq);
+		else
+			irq_set_chip_and_handler(virq, &s3c_irq_chip,
+						 handle_level_irq);
+		break;
+	default:
+		pr_err("irq-s3c24xx: unsupported irqtype %d\n", irq_data->type);
+		return -EINVAL;
+	}
+
+	irq_set_chip_data(virq, irq_data);
+
+	if (parent_intc && irq_data->type != S3C_IRQTYPE_NONE) {
+		if (irq_data->parent_irq > 31) {
+			pr_err("irq-s3c24xx: parent irq %lu is out of range\n",
+			       irq_data->parent_irq);
+			return -EINVAL;
+		}
+
+		parent_irq_data = &parent_intc->irqs[irq_data->parent_irq];
+		parent_irq_data->sub_intc = intc;
+		parent_irq_data->sub_bits |= (1UL << hw);
+
+		/* attach the demuxer to the parent irq */
+		irqno = irq_find_mapping(parent_intc->domain,
+					 irq_data->parent_irq);
+		if (!irqno) {
+			pr_err("irq-s3c24xx: could not find mapping for parent irq %lu\n",
+			       irq_data->parent_irq);
+			return -EINVAL;
+		}
+		irq_set_chained_handler(irqno, s3c_irq_demux);
+	}
+
+	return 0;
+}
+
+static const struct irq_domain_ops s3c24xx_irq_ops = {
+	.map = s3c24xx_irq_map,
+	.xlate = irq_domain_xlate_twocell,
+};
+
+static void s3c24xx_clear_intc(struct s3c_irq_intc *intc)
+{
+	void __iomem *reg_source;
+	unsigned long pend;
+	unsigned long last;
+	int i;
+
+	/* if intpnd is set, read the next pending irq from there */
+	reg_source = intc->reg_intpnd ? intc->reg_intpnd : intc->reg_pending;
+
+	last = 0;
+	for (i = 0; i < 4; i++) {
+		pend = readl_relaxed(reg_source);
+
+		if (pend == 0 || pend == last)
+			break;
+
+		writel_relaxed(pend, intc->reg_pending);
+		if (intc->reg_intpnd)
+			writel_relaxed(pend, intc->reg_intpnd);
+
+		pr_info("irq: clearing pending status %08x\n", (int)pend);
+		last = pend;
+	}
+}
+
+static struct s3c_irq_intc * __init s3c24xx_init_intc(struct device_node *np,
+				       struct s3c_irq_data *irq_data,
+				       struct s3c_irq_intc *parent,
+				       unsigned long address)
+{
+	struct s3c_irq_intc *intc;
+	void __iomem *base = (void *)0xf6000000; /* static mapping */
+	int irq_num;
+	int irq_start;
+	int ret;
+
+	intc = kzalloc(sizeof(struct s3c_irq_intc), GFP_KERNEL);
+	if (!intc)
+		return ERR_PTR(-ENOMEM);
+
+	intc->irqs = irq_data;
+
+	if (parent)
+		intc->parent = parent;
+
+	/* select the correct data for the controller.
+	 * Need to hard code the irq num start and offset
+	 * to preserve the static mapping for now
+	 */
+	switch (address) {
+	case 0x4a000000:
+		pr_debug("irq: found main intc\n");
+		intc->reg_pending = base;
+		intc->reg_mask = base + 0x08;
+		intc->reg_intpnd = base + 0x10;
+		irq_num = 32;
+		irq_start = S3C2410_IRQ(0);
+		break;
+	case 0x4a000018:
+		pr_debug("irq: found subintc\n");
+		intc->reg_pending = base + 0x18;
+		intc->reg_mask = base + 0x1c;
+		irq_num = 29;
+		irq_start = S3C2410_IRQSUB(0);
+		break;
+	case 0x4a000040:
+		pr_debug("irq: found intc2\n");
+		intc->reg_pending = base + 0x40;
+		intc->reg_mask = base + 0x48;
+		intc->reg_intpnd = base + 0x50;
+		irq_num = 8;
+		irq_start = S3C2416_IRQ(0);
+		break;
+	case 0x560000a4:
+		pr_debug("irq: found eintc\n");
+		base = (void *)0xfd000000;
+
+		intc->reg_mask = base + 0xa4;
+		intc->reg_pending = base + 0xa8;
+		irq_num = 24;
+		irq_start = S3C2410_IRQ(32);
+		break;
+	default:
+		pr_err("irq: unsupported controller address\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	/* now that all the data is complete, init the irq-domain */
+	s3c24xx_clear_intc(intc);
+	intc->domain = irq_domain_add_legacy(np, irq_num, irq_start,
+					     0, &s3c24xx_irq_ops,
+					     intc);
+	if (!intc->domain) {
+		pr_err("irq: could not create irq-domain\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	set_handle_irq(s3c24xx_handle_irq);
+
+	return intc;
+
+err:
+	kfree(intc);
+	return ERR_PTR(ret);
+}
+
+static struct s3c_irq_data __maybe_unused init_eint[32] = {
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT4 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT5 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT6 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT7 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT8 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT9 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT10 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT11 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT12 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT13 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT14 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT15 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT16 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT17 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT18 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT19 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT20 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT21 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT22 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT23 */
+};
+
+#ifdef CONFIG_CPU_S3C2410
+static struct s3c_irq_data init_s3c2410base[32] = {
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* WDT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* LCD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+static struct s3c_irq_data init_s3c2410subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+};
+
+void __init s3c2410_init_irq(void)
+{
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2410base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2410subint[0],
+					s3c_intc[0], 0x4a000018);
+	s3c24xx_init_intc(NULL, &init_eint[0], s3c_intc[0], 0x560000a4);
+}
+#endif
+
+#ifdef CONFIG_CPU_S3C2412
+static struct s3c_irq_data init_s3c2412base[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* WDT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* LCD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* SDI/CF */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+static struct s3c_irq_data init_s3c2412eint[32] = {
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 0 }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 1 }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 2 }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 3 }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT4 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT5 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT6 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 4 }, /* EINT7 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT8 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT9 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT10 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT11 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT12 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT13 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT14 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT15 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT16 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT17 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT18 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT19 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT20 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT21 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT22 */
+	{ .type = S3C_IRQTYPE_EINT, .parent_irq = 5 }, /* EINT23 */
+};
+
+static struct s3c_irq_data init_s3c2412subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+	{ .type = S3C_IRQTYPE_NONE, },
+	{ .type = S3C_IRQTYPE_NONE, },
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 21 }, /* SDI */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 21 }, /* CF */
+};
+
+void __init s3c2412_init_irq(void)
+{
+	pr_info("S3C2412: IRQ Support\n");
+
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2412base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c24xx_init_intc(NULL, &init_s3c2412eint[0], s3c_intc[0], 0x560000a4);
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2412subint[0],
+					s3c_intc[0], 0x4a000018);
+}
+#endif
+
+#ifdef CONFIG_CPU_S3C2416
+static struct s3c_irq_data init_s3c2416base[32] = {
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* WDT/AC97 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* LCD */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* DMA */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART3 */
+	{ .type = S3C_IRQTYPE_NONE, }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* NAND */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_NONE, },
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+static struct s3c_irq_data init_s3c2416subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD2 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD3 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD4 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA4 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA5 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* WDT */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* AC97 */
+};
+
+static struct s3c_irq_data init_s3c2416_second[32] = {
+	{ .type = S3C_IRQTYPE_EDGE }, /* 2D */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE }, /* PCM0 */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_EDGE }, /* I2S0 */
+};
+
+void __init s3c2416_init_irq(void)
+{
+	pr_info("S3C2416: IRQ Support\n");
+
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2416base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c24xx_init_intc(NULL, &init_eint[0], s3c_intc[0], 0x560000a4);
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2416subint[0],
+					s3c_intc[0], 0x4a000018);
+
+	s3c_intc[2] = s3c24xx_init_intc(NULL, &init_s3c2416_second[0],
+					NULL, 0x4a000040);
+}
+
+#endif
+
+#ifdef CONFIG_CPU_S3C2440
+static struct s3c_irq_data init_s3c2440base[32] = {
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* CAM */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* WDT/AC97 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* LCD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* NFCON */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+static struct s3c_irq_data init_s3c2440subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_C */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_P */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* WDT */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* AC97 */
+};
+
+void __init s3c2440_init_irq(void)
+{
+	pr_info("S3C2440: IRQ Support\n");
+
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2440base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c24xx_init_intc(NULL, &init_eint[0], s3c_intc[0], 0x560000a4);
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2440subint[0],
+					s3c_intc[0], 0x4a000018);
+}
+#endif
+
+#ifdef CONFIG_CPU_S3C2442
+static struct s3c_irq_data init_s3c2442base[32] = {
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* CAM */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* WDT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* LCD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* NFCON */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+static struct s3c_irq_data init_s3c2442subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_C */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_P */
+};
+
+void __init s3c2442_init_irq(void)
+{
+	pr_info("S3C2442: IRQ Support\n");
+
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2442base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c24xx_init_intc(NULL, &init_eint[0], s3c_intc[0], 0x560000a4);
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2442subint[0],
+					s3c_intc[0], 0x4a000018);
+}
+#endif
+
+#ifdef CONFIG_CPU_S3C2443
+static struct s3c_irq_data init_s3c2443base[32] = {
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT0 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT1 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT2 */
+	{ .type = S3C_IRQTYPE_EINT, }, /* EINT3 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT4to7 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* EINT8to23 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* CAM */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* nBATT_FLT */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TICK */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* WDT/AC97 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER2 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* TIMER4 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART2 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* LCD */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* DMA */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART3 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* CFON */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SDI0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI0 */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* NAND */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBD */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* USBH */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* IIC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* UART0 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* SPI1 */
+	{ .type = S3C_IRQTYPE_EDGE, }, /* RTC */
+	{ .type = S3C_IRQTYPE_LEVEL, }, /* ADCPARENT */
+};
+
+
+static struct s3c_irq_data init_s3c2443subint[32] = {
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 28 }, /* UART0-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 23 }, /* UART1-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 15 }, /* UART2-ERR */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* TC */
+	{ .type = S3C_IRQTYPE_EDGE, .parent_irq = 31 }, /* ADC */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_C */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 6 }, /* CAM_P */
+	{ .type = S3C_IRQTYPE_NONE }, /* reserved */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD1 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD2 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD3 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 16 }, /* LCD4 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA0 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA1 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA2 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA3 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA4 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 17 }, /* DMA5 */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-RX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-TX */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 18 }, /* UART3-ERR */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* WDT */
+	{ .type = S3C_IRQTYPE_LEVEL, .parent_irq = 9 }, /* AC97 */
+};
+
+void __init s3c2443_init_irq(void)
+{
+	pr_info("S3C2443: IRQ Support\n");
+
+#ifdef CONFIG_FIQ
+	init_FIQ(FIQ_START);
+#endif
+
+	s3c_intc[0] = s3c24xx_init_intc(NULL, &init_s3c2443base[0], NULL,
+					0x4a000000);
+	if (IS_ERR(s3c_intc[0])) {
+		pr_err("irq: could not create main interrupt controller\n");
+		return;
+	}
+
+	s3c24xx_init_intc(NULL, &init_eint[0], s3c_intc[0], 0x560000a4);
+	s3c_intc[1] = s3c24xx_init_intc(NULL, &init_s3c2443subint[0],
+					s3c_intc[0], 0x4a000018);
+}
+#endif
+
+#ifdef CONFIG_OF
+static int s3c24xx_irq_map_of(struct irq_domain *h, unsigned int virq,
+							irq_hw_number_t hw)
+{
+	unsigned int ctrl_num = hw / 32;
+	unsigned int intc_hw = hw % 32;
+	struct s3c_irq_intc *intc = s3c_intc[ctrl_num];
+	struct s3c_irq_intc *parent_intc = intc->parent;
+	struct s3c_irq_data *irq_data = &intc->irqs[intc_hw];
+
+	/* attach controller pointer to irq_data */
+	irq_data->intc = intc;
+	irq_data->offset = intc_hw;
+
+	if (!parent_intc)
+		irq_set_chip_and_handler(virq, &s3c_irq_chip, handle_edge_irq);
+	else
+		irq_set_chip_and_handler(virq, &s3c_irq_level_chip,
+					 handle_edge_irq);
+
+	irq_set_chip_data(virq, irq_data);
+
+	return 0;
+}
+
+/* Translate our of irq notation
+ * format: <ctrl_num ctrl_irq parent_irq type>
+ */
+static int s3c24xx_irq_xlate_of(struct irq_domain *d, struct device_node *n,
+			const u32 *intspec, unsigned int intsize,
+			irq_hw_number_t *out_hwirq, unsigned int *out_type)
+{
+	struct s3c_irq_intc *intc;
+	struct s3c_irq_intc *parent_intc;
+	struct s3c_irq_data *irq_data;
+	struct s3c_irq_data *parent_irq_data;
+	int irqno;
+
+	if (WARN_ON(intsize < 4))
+		return -EINVAL;
+
+	if (intspec[0] > 2 || !s3c_intc[intspec[0]]) {
+		pr_err("controller number %d invalid\n", intspec[0]);
+		return -EINVAL;
+	}
+	intc = s3c_intc[intspec[0]];
+
+	*out_hwirq = intspec[0] * 32 + intspec[2];
+	*out_type = intspec[3] & IRQ_TYPE_SENSE_MASK;
+
+	parent_intc = intc->parent;
+	if (parent_intc) {
+		irq_data = &intc->irqs[intspec[2]];
+		irq_data->parent_irq = intspec[1];
+		parent_irq_data = &parent_intc->irqs[irq_data->parent_irq];
+		parent_irq_data->sub_intc = intc;
+		parent_irq_data->sub_bits |= (1UL << intspec[2]);
+
+		/* parent_intc is always s3c_intc[0], so no offset */
+		irqno = irq_create_mapping(parent_intc->domain, intspec[1]);
+		if (irqno < 0) {
+			pr_err("irq: could not map parent interrupt\n");
+			return irqno;
+		}
+
+		irq_set_chained_handler(irqno, s3c_irq_demux);
+	}
+
+	return 0;
+}
+
+static const struct irq_domain_ops s3c24xx_irq_ops_of = {
+	.map = s3c24xx_irq_map_of,
+	.xlate = s3c24xx_irq_xlate_of,
+};
+
+struct s3c24xx_irq_of_ctrl {
+	char			*name;
+	unsigned long		offset;
+	struct s3c_irq_intc	**handle;
+	struct s3c_irq_intc	**parent;
+	struct irq_domain_ops	*ops;
+};
+
+static int __init s3c_init_intc_of(struct device_node *np,
+			struct device_node *interrupt_parent,
+			struct s3c24xx_irq_of_ctrl *s3c_ctrl, int num_ctrl)
+{
+	struct s3c_irq_intc *intc;
+	struct s3c24xx_irq_of_ctrl *ctrl;
+	struct irq_domain *domain;
+	void __iomem *reg_base;
+	int i;
+
+	reg_base = of_iomap(np, 0);
+	if (!reg_base) {
+		pr_err("irq-s3c24xx: could not map irq registers\n");
+		return -EINVAL;
+	}
+
+	domain = irq_domain_add_linear(np, num_ctrl * 32,
+						     &s3c24xx_irq_ops_of, NULL);
+	if (!domain) {
+		pr_err("irq: could not create irq-domain\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < num_ctrl; i++) {
+		ctrl = &s3c_ctrl[i];
+
+		pr_debug("irq: found controller %s\n", ctrl->name);
+
+		intc = kzalloc(sizeof(struct s3c_irq_intc), GFP_KERNEL);
+		if (!intc)
+			return -ENOMEM;
+
+		intc->domain = domain;
+		intc->irqs = kcalloc(32, sizeof(struct s3c_irq_data),
+				     GFP_KERNEL);
+		if (!intc->irqs) {
+			kfree(intc);
+			return -ENOMEM;
+		}
+
+		if (ctrl->parent) {
+			intc->reg_pending = reg_base + ctrl->offset;
+			intc->reg_mask = reg_base + ctrl->offset + 0x4;
+
+			if (*(ctrl->parent)) {
+				intc->parent = *(ctrl->parent);
+			} else {
+				pr_warn("irq: parent of %s missing\n",
+					ctrl->name);
+				kfree(intc->irqs);
+				kfree(intc);
+				continue;
+			}
+		} else {
+			intc->reg_pending = reg_base + ctrl->offset;
+			intc->reg_mask = reg_base + ctrl->offset + 0x08;
+			intc->reg_intpnd = reg_base + ctrl->offset + 0x10;
+		}
+
+		s3c24xx_clear_intc(intc);
+		s3c_intc[i] = intc;
+	}
+
+	set_handle_irq(s3c24xx_handle_irq);
+
+	return 0;
+}
+
+static struct s3c24xx_irq_of_ctrl s3c2410_ctrl[] = {
+	{
+		.name = "intc",
+		.offset = 0,
+	}, {
+		.name = "subintc",
+		.offset = 0x18,
+		.parent = &s3c_intc[0],
+	}
+};
+
+int __init s3c2410_init_intc_of(struct device_node *np,
+			struct device_node *interrupt_parent)
+{
+	return s3c_init_intc_of(np, interrupt_parent,
+				s3c2410_ctrl, ARRAY_SIZE(s3c2410_ctrl));
+}
+IRQCHIP_DECLARE(s3c2410_irq, "samsung,s3c2410-irq", s3c2410_init_intc_of);
+
+static struct s3c24xx_irq_of_ctrl s3c2416_ctrl[] = {
+	{
+		.name = "intc",
+		.offset = 0,
+	}, {
+		.name = "subintc",
+		.offset = 0x18,
+		.parent = &s3c_intc[0],
+	}, {
+		.name = "intc2",
+		.offset = 0x40,
+	}
+};
+
+int __init s3c2416_init_intc_of(struct device_node *np,
+			struct device_node *interrupt_parent)
+{
+	return s3c_init_intc_of(np, interrupt_parent,
+				s3c2416_ctrl, ARRAY_SIZE(s3c2416_ctrl));
+}
+IRQCHIP_DECLARE(s3c2416_irq, "samsung,s3c2416-irq", s3c2416_init_intc_of);
+#endif
diff --git a/arch/arm/mach-s3c64xx/irq-uart.h b/arch/arm/mach-s3c/irq-uart-s3c64xx.h
index 78eccdce95a7..78eccdce95a7 100644
--- a/arch/arm/mach-s3c64xx/irq-uart.h
+++ b/arch/arm/mach-s3c/irq-uart-s3c64xx.h
diff --git a/arch/arm/plat-samsung/include/plat/keypad.h b/arch/arm/mach-s3c/keypad.h
index 9754b9a29945..9754b9a29945 100644
--- a/arch/arm/plat-samsung/include/plat/keypad.h
+++ b/arch/arm/mach-s3c/keypad.h
diff --git a/arch/arm/mach-s3c24xx/mach-amlm5900.c b/arch/arm/mach-s3c/mach-amlm5900.c
index 9a9daf526d0c..94c4512ace17 100644
--- a/arch/arm/mach-s3c24xx/mach-amlm5900.c
+++ b/arch/arm/mach-s3c/mach-amlm5900.c
@@ -13,6 +13,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
@@ -26,28 +27,24 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/flash.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 
-#include <mach/regs-lcd.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/gpio-cfg.h>
+#include "devs.h"
+#include "cpu.h"
+#include "gpio-cfg.h"
 
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/map.h>
 #include <linux/mtd/physmap.h>
 
-#include <plat/samsung-time.h>
-
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct resource amlm5900_nor_resource =
 			DEFINE_RES_MEM(0x00000000, SZ_16M);
@@ -124,6 +121,19 @@ static struct s3c2410_uartcfg amlm5900_uartcfgs[] = {
 	}
 };
 
+static struct gpiod_lookup_table amlm5900_mmc_gpio_table = {
+	.dev_id = "s3c2410-sdi",
+	.table = {
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 static struct platform_device *amlm5900_devices[] __initdata = {
 #ifdef CONFIG_FB_S3C2410
@@ -143,13 +153,13 @@ static void __init amlm5900_map_io(void)
 {
 	s3c24xx_init_io(amlm5900_iodesc, ARRAY_SIZE(amlm5900_iodesc));
 	s3c24xx_init_uarts(amlm5900_uartcfgs, ARRAY_SIZE(amlm5900_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init amlm5900_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 #ifdef CONFIG_FB_S3C2410
@@ -180,13 +190,17 @@ static struct s3c2410fb_mach_info __initdata amlm5900_fb_info = {
 
 	.gpccon =	0xaaaaaaaa,
 	.gpccon_mask =	0xffffffff,
+	.gpccon_reg =	S3C2410_GPCCON,
 	.gpcup =	0x0000ffff,
 	.gpcup_mask =	0xffffffff,
+	.gpcup_reg =	S3C2410_GPCUP,
 
 	.gpdcon =	0xaaaaaaaa,
 	.gpdcon_mask =	0xffffffff,
+	.gpdcon_reg =	S3C2410_GPDCON,
 	.gpdup =	0x0000ffff,
 	.gpdup_mask =	0xffffffff,
+	.gpdup_reg =	S3C2410_GPDUP,
 };
 #endif
 
@@ -219,6 +233,7 @@ static void __init amlm5900_init(void)
 	s3c24xx_fb_set_platdata(&amlm5900_fb_info);
 #endif
 	s3c_i2c0_set_platdata(NULL);
+	gpiod_add_lookup_table(&amlm5900_mmc_gpio_table);
 	platform_add_devices(amlm5900_devices, ARRAY_SIZE(amlm5900_devices));
 }
 
diff --git a/arch/arm/mach-s3c24xx/mach-anubis.c b/arch/arm/mach-s3c/mach-anubis.c
index 28326241e360..90e3fd98a3ac 100644
--- a/arch/arm/mach-s3c24xx/mach-anubis.c
+++ b/arch/arm/mach-s3c/mach-anubis.c
@@ -24,13 +24,11 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
@@ -41,13 +39,12 @@
 
 #include <net/ax88796.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
 #include <linux/platform_data/asoc-s3c24xx_simtec.h>
-#include <plat/samsung-time.h>
 
 #include "anubis.h"
-#include "common.h"
+#include "s3c24xx.h"
 #include "simtec.h"
 
 #define COPYRIGHT ", Copyright 2005-2009 Simtec Electronics"
@@ -384,7 +381,7 @@ static void __init anubis_map_io(void)
 {
 	s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc));
 	s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 
 	/* check for the newer revision boards with large page nand */
 
@@ -403,7 +400,7 @@ static void __init anubis_map_io(void)
 static void __init anubis_init_time(void)
 {
 	s3c2440_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init anubis_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-anw6410.c b/arch/arm/mach-s3c/mach-anw6410.c
index 0d3d5befb806..825714e9ac66 100644
--- a/arch/arm/mach-s3c64xx/mach-anw6410.c
+++ b/arch/arm/mach-s3c/mach-anw6410.c
@@ -30,24 +30,22 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
+#include "fb.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
 #include <mach/irqs.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-#include <plat/samsung-time.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include "common.h"
-#include "regs-modem.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
 
 /* DM9000 */
 #define ANW6410_PA_DM9000	(0x18000000)
@@ -204,7 +202,7 @@ static void __init anw6410_map_io(void)
 	s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc));
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	anw6410_lcd_mode_set();
 }
@@ -228,6 +226,5 @@ MACHINE_START(ANW6410, "A&W6410")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= anw6410_map_io,
 	.init_machine	= anw6410_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-at2440evb.c b/arch/arm/mach-s3c/mach-at2440evb.c
index 04dedebdb57c..5fa49d4e2650 100644
--- a/arch/arm/mach-s3c24xx/mach-at2440evb.c
+++ b/arch/arm/mach-s3c/mach-at2440evb.c
@@ -24,14 +24,12 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
@@ -40,12 +38,11 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
 #include <linux/platform_data/mmc-s3cmci.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct map_desc at2440evb_iodesc[] __initdata = {
 	/* Nothing here */
@@ -136,18 +133,26 @@ static struct platform_device at2440evb_device_eth = {
 };
 
 static struct s3c24xx_mci_pdata at2440evb_mci_pdata __initdata = {
-	/* Intentionally left blank */
+	.set_power	= s3c24xx_mci_def_set_power,
 };
 
 static struct gpiod_lookup_table at2440evb_mci_gpio_table = {
 	.dev_id = "s3c2410-sdi",
 	.table = {
 		/* Card detect S3C2410_GPG(10) */
-		GPIO_LOOKUP("GPG", 10, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOG", 10, "cd", GPIO_ACTIVE_LOW),
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
 		{ },
 	},
 };
 
+
 /* 7" LCD panel */
 
 static struct s3c2410fb_display at2440evb_lcd_cfg __initdata = {
@@ -197,13 +202,13 @@ static void __init at2440evb_map_io(void)
 {
 	s3c24xx_init_io(at2440evb_iodesc, ARRAY_SIZE(at2440evb_iodesc));
 	s3c24xx_init_uarts(at2440evb_uartcfgs, ARRAY_SIZE(at2440evb_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init at2440evb_init_time(void)
 {
 	s3c2440_init_clocks(16934400);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init at2440evb_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-bast.c b/arch/arm/mach-s3c/mach-bast.c
index 6465eab0ab3a..328f5d9ae9f9 100644
--- a/arch/arm/mach-s3c24xx/mach-bast.c
+++ b/arch/arm/mach-s3c/mach-bast.c
@@ -40,20 +40,17 @@
 #include <asm/mach/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
-
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include <linux/platform_data/fb-s3c2410.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "devs.h"
+#include "gpio-cfg.h"
 
 #include "bast.h"
-#include "common.h"
+#include "s3c24xx.h"
 #include "simtec.h"
 
 #define COPYRIGHT ", Copyright 2004-2008 Simtec Electronics"
@@ -550,13 +547,13 @@ static void __init bast_map_io(void)
 
 	s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
 	s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init bast_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init bast_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index 34f1baa10c54..407ad493493e 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -27,7 +27,7 @@
 
 #include <linux/platform_data/spi-s3c64xx.h>
 
-#include <plat/cpu.h>
+#include "cpu.h"
 #include <mach/irqs.h>
 
 #include "crag6410.h"
@@ -378,8 +378,7 @@ static const struct {
 	  .i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c) },
 };
 
-static int wlf_gf_module_probe(struct i2c_client *i2c,
-			       const struct i2c_device_id *i2c_id)
+static int wlf_gf_module_probe(struct i2c_client *i2c)
 {
 	int ret, i, j, id, rev;
 
@@ -432,7 +431,7 @@ static struct i2c_driver wlf_gf_module_driver = {
 	.driver = {
 		.name = "wlf-gf-module"
 	},
-	.probe = wlf_gf_module_probe,
+	.probe_new = wlf_gf_module_probe,
 	.id_table = wlf_gf_module_id,
 };
 
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c/mach-crag6410.c
index da9654255e3f..4a12c75d407f 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c/mach-crag6410.c
@@ -44,30 +44,28 @@
 #include <asm/mach-types.h>
 
 #include <video/samsung_fimd.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <mach/irqs.h>
 
-#include <plat/fb.h>
-#include <plat/sdhci.h>
-#include <plat/gpio-cfg.h>
+#include "fb.h"
+#include "sdhci.h"
+#include "gpio-cfg.h"
 #include <linux/platform_data/spi-s3c64xx.h>
 
-#include <plat/keypad.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc.h>
+#include "keypad.h"
+#include "devs.h"
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-adc.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "pm.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 #include "crag6410.h"
-#include "regs-gpio-memport.h"
-#include "regs-modem.h"
-#include "regs-sys.h"
+#include "regs-gpio-memport-s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
 
 /* serial port setup */
 
@@ -750,7 +748,7 @@ static void __init crag6410_map_io(void)
 	s3c64xx_init_io(NULL, 0);
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(crag6410_uartcfgs, ARRAY_SIZE(crag6410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	/* LCD type and Bypass set by bootloader */
 }
@@ -877,6 +875,5 @@ MACHINE_START(WLF_CRAGG_6410, "Wolfson Cragganmore 6410")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= crag6410_map_io,
 	.init_machine	= crag6410_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-gta02.c b/arch/arm/mach-s3c/mach-gta02.c
index 732748170751..3c75c7d112ea 100644
--- a/arch/arm/mach-s3c24xx/mach-gta02.c
+++ b/arch/arm/mach-s3c/mach-gta02.c
@@ -57,20 +57,18 @@
 #include <linux/platform_data/touchscreen-s3c2410.h>
 #include <linux/platform_data/usb-ohci-s3c2410.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/fb-s3c2410.h>
 
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-irq.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "regs-irq.h"
+#include "gpio-samsung.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "gpio-cfg.h"
+#include "pm.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 #include "gta02.h"
 
 static struct pcf50633 *gta02_pcf;
@@ -489,11 +487,25 @@ static struct platform_device gta02_audio = {
 	.id = -1,
 };
 
+static struct gpiod_lookup_table gta02_mmc_gpio_table = {
+	.dev_id = "s3c2410-sdi",
+	.table = {
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init gta02_map_io(void)
 {
 	s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc));
 	s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 
@@ -540,7 +552,12 @@ static void __init gta02_machine_init(void)
 
 	i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs));
 
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
+
 	gpiod_add_lookup_table(&gta02_audio_gpio_table);
+	gpiod_add_lookup_table(&gta02_mmc_gpio_table);
 	platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
 	pm_power_off = gta02_poweroff;
 
@@ -550,7 +567,7 @@ static void __init gta02_machine_init(void)
 static void __init gta02_init_time(void)
 {
 	s3c2442_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 MACHINE_START(NEO1973_GTA02, "GTA02")
diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c/mach-h1940.c
index ecb84029e15c..53d51aa83200 100644
--- a/arch/arm/mach-s3c24xx/mach-h1940.c
+++ b/arch/arm/mach-s3c/mach-h1940.c
@@ -47,20 +47,19 @@
 
 #include <sound/uda1380.h>
 
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
-
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
-
-#include "common.h"
+#include <linux/platform_data/fb-s3c2410.h>
+#include "map.h"
+#include "hardware-s3c24xx.h"
+#include "regs-clock.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include "cpu.h"
+#include "devs.h"
+#include "gpio-cfg.h"
+#include "pm.h"
+
+#include "s3c24xx.h"
 #include "h1940.h"
 
 #define H1940_LATCH		((void __force __iomem *)0xF8000000)
@@ -180,9 +179,9 @@ static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = {
 		.cfg_gpio = s3c24xx_ts_cfg_gpio,
 };
 
-/**
+/*
  * Set lcd on or off
- **/
+ */
 static struct s3c2410fb_display h1940_lcd __initdata = {
 	.lcdcon5=	S3C2410_LCDCON5_FRM565 | \
 			S3C2410_LCDCON5_INVVLINE | \
@@ -211,12 +210,16 @@ static struct s3c2410fb_mach_info h1940_fb_info __initdata = {
 	.lpcsel =	0x02,
 	.gpccon =	0xaa940659,
 	.gpccon_mask =	0xffffc0f0,
+	.gpccon_reg =	S3C2410_GPCCON,
 	.gpcup =	0x0000ffff,
 	.gpcup_mask =	0xffffffff,
+	.gpcup_reg =	S3C2410_GPCUP,
 	.gpdcon =	0xaa84aaa0,
 	.gpdcon_mask =	0xffffffff,
+	.gpdcon_reg =	S3C2410_GPDCON,
 	.gpdup =	0x0000faff,
 	.gpdup_mask =	0xffffffff,
+	.gpdup_reg =	S3C2410_GPDUP,
 };
 
 static int power_supply_init(struct device *dev)
@@ -446,6 +449,8 @@ static struct platform_device h1940_device_bluetooth = {
 
 static void h1940_set_mmc_power(unsigned char power_mode, unsigned short vdd)
 {
+	s3c24xx_mci_def_set_power(power_mode, vdd);
+
 	switch (power_mode) {
 	case MMC_POWER_OFF:
 		gpio_set_value(H1940_LATCH_SD_POWER, 0);
@@ -468,9 +473,16 @@ static struct gpiod_lookup_table h1940_mmc_gpio_table = {
 	.dev_id = "s3c2410-sdi",
 	.table = {
 		/* Card detect S3C2410_GPF(5) */
-		GPIO_LOOKUP("GPF", 5, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOF", 5, "cd", GPIO_ACTIVE_LOW),
 		/* Write protect S3C2410_GPH(8) */
-		GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_LOW),
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
 		{ },
 	},
 };
@@ -674,7 +686,7 @@ static void __init h1940_map_io(void)
 {
 	s3c24xx_init_io(h1940_iodesc, ARRAY_SIZE(h1940_iodesc));
 	s3c24xx_init_uarts(h1940_uartcfgs, ARRAY_SIZE(h1940_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 
 	/* setup PM */
 
@@ -691,7 +703,7 @@ static void __init h1940_map_io(void)
 static void __init h1940_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 /* H1940 and RX3715 need to reserve this for suspend */
@@ -708,6 +720,9 @@ static void __init h1940_init(void)
 	s3c24xx_fb_set_platdata(&h1940_fb_info);
 	gpiod_add_lookup_table(&h1940_mmc_gpio_table);
 	gpiod_add_lookup_table(&h1940_audio_gpio_table);
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	s3c24xx_mci_set_platdata(&h1940_mmc_cfg);
  	s3c24xx_udc_set_platdata(&h1940_udc_cfg);
 	s3c24xx_ts_set_platdata(&h1940_ts_cfg);
diff --git a/arch/arm/mach-s3c64xx/mach-hmt.c b/arch/arm/mach-s3c/mach-hmt.c
index 0d9acaf91701..b287e9987311 100644
--- a/arch/arm/mach-s3c64xx/mach-hmt.c
+++ b/arch/arm/mach-s3c/mach-hmt.c
@@ -25,23 +25,21 @@
 #include <asm/mach/irq.h>
 
 #include <video/samsung_fimd.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 #include <mach/irqs.h>
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <plat/fb.h>
+#include "gpio-samsung.h"
+#include "fb.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT
 #define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
@@ -251,7 +249,7 @@ static void __init hmt_map_io(void)
 	s3c64xx_init_io(hmt_iodesc, ARRAY_SIZE(hmt_iodesc));
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(hmt_uartcfgs, ARRAY_SIZE(hmt_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 }
 
 static void __init hmt_machine_init(void)
@@ -280,6 +278,5 @@ MACHINE_START(HMT, "Airgoo-HMT")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= hmt_map_io,
 	.init_machine	= hmt_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-jive.c b/arch/arm/mach-s3c/mach-jive.c
index 8233dcff19e7..2a29c3eca559 100644
--- a/arch/arm/mach-s3c24xx/mach-jive.c
+++ b/arch/arm/mach-s3c/mach-jive.c
@@ -31,10 +31,10 @@
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/fb.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include <linux/platform_data/fb-s3c2410.h>
+#include "gpio-samsung.h"
 
 #include <asm/mach-types.h>
 
@@ -43,14 +43,13 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
 #include <linux/platform_data/usb-s3c2410_udc.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
+#include "s3c24xx.h"
 #include "s3c2412-power.h"
 
 static struct map_desc jive_iodesc[] __initdata = {
@@ -321,6 +320,7 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
 	 * data. */
 
 	.gpcup		= (0xf << 1) | (0x3f << 10),
+	.gpcup_reg	= S3C2410_GPCUP,
 
 	.gpccon		= (S3C2410_GPC1_VCLK   | S3C2410_GPC2_VLINE |
 			   S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
@@ -334,8 +334,12 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
 			   S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
 			   S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
 
+	.gpccon_reg	= S3C2410_GPCCON,
+
 	.gpdup		= (0x3f << 2) | (0x3f << 10),
 
+	.gpdup_reg	= S3C2410_GPDUP,
+
 	.gpdcon		= (S3C2410_GPD2_VD10  | S3C2410_GPD3_VD11 |
 			   S3C2410_GPD4_VD12  | S3C2410_GPD5_VD13 |
 			   S3C2410_GPD6_VD14  | S3C2410_GPD7_VD15 |
@@ -349,6 +353,8 @@ static struct s3c2410fb_mach_info jive_lcd_config = {
 			   S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
 			   S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
 			   S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+
+	.gpdcon_reg	= S3C2410_GPDCON,
 };
 
 /* ILI9320 support. */
@@ -523,13 +529,13 @@ static void __init jive_map_io(void)
 {
 	s3c24xx_init_io(jive_iodesc, ARRAY_SIZE(jive_iodesc));
 	s3c24xx_init_uarts(jive_uartcfgs, ARRAY_SIZE(jive_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init jive_init_time(void)
 {
 	s3c2412_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void jive_power_off(void)
diff --git a/arch/arm/mach-s3c24xx/mach-mini2440.c b/arch/arm/mach-s3c/mach-mini2440.c
index 057dcbaf1b22..dc22ab839b95 100644
--- a/arch/arm/mach-s3c24xx/mach-mini2440.c
+++ b/arch/arm/mach-s3c/mach-mini2440.c
@@ -30,15 +30,13 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/hardware.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
 #include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-lcd.h>
 #include <mach/irqs.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <linux/platform_data/mmc-s3cmci.h>
@@ -49,14 +47,13 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
 
 #include <sound/s3c24xx_uda134x.h>
 
-#include "common.h"
+#include "s3c24xx.h"
 
 #define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
 
@@ -215,6 +212,9 @@ static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
 			   S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
 			   S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
 
+	.gpccon_reg	= S3C2410_GPCCON,
+	.gpcup_reg	= S3C2410_GPCUP,
+
 	.gpdup		= (0x3f << 2) | (0x3f << 10),
 
 	.gpdcon		= (S3C2410_GPD2_VD10  | S3C2410_GPD3_VD11 |
@@ -230,13 +230,16 @@ static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
 			   S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
 			   S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
 			   S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+
+	.gpdcon_reg	= S3C2410_GPDCON,
+	.gpdup_reg	= S3C2410_GPDUP,
 };
 
 /* MMC/SD  */
 
 static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
 	.wprotect_invert	= 1,
-	.set_power		= NULL,
+	.set_power		= s3c24xx_mci_def_set_power,
 	.ocr_avail		= MMC_VDD_32_33|MMC_VDD_33_34,
 };
 
@@ -244,9 +247,16 @@ static struct gpiod_lookup_table mini2440_mmc_gpio_table = {
 	.dev_id = "s3c2410-sdi",
 	.table = {
 		/* Card detect S3C2410_GPG(8) */
-		GPIO_LOOKUP("GPG", 8, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOG", 8, "cd", GPIO_ACTIVE_LOW),
 		/* Write protect S3C2410_GPH(8) */
-		GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_HIGH),
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
 		{ },
 	},
 };
@@ -587,13 +597,13 @@ static void __init mini2440_map_io(void)
 {
 	s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
 	s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init mini2440_init_time(void)
 {
 	s3c2440_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 /*
@@ -716,6 +726,11 @@ static void __init mini2440_init(void)
 		s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
 		s3c_gpio_cfgpin(mini2440_buttons[i].gpio, S3C2410_GPIO_INPUT);
 	}
+
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
+
 	if (features.lcd_index != -1) {
 		int li;
 
diff --git a/arch/arm/mach-s3c64xx/mach-mini6410.c b/arch/arm/mach-s3c/mach-mini6410.c
index 6fbb57878746..741fa1f09694 100644
--- a/arch/arm/mach-s3c64xx/mach-mini6410.c
+++ b/arch/arm/mach-s3c/mach-mini6410.c
@@ -23,27 +23,26 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-
-#include <plat/adc.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include <linux/soc/samsung/s3c-adc.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/mmc-sdhci-s3c.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
 #include <linux/platform_data/touchscreen-s3c2410.h>
 #include <mach/irqs.h>
 
 #include <video/platform_lcd.h>
 #include <video/samsung_fimd.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT
 #define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
@@ -238,7 +237,7 @@ static void __init mini6410_map_io(void)
 	s3c64xx_init_io(NULL, 0);
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(mini6410_uartcfgs, ARRAY_SIZE(mini6410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	/* set the LCD type */
 	tmp = __raw_readl(S3C64XX_SPCON);
@@ -362,6 +361,5 @@ MACHINE_START(MINI6410, "MINI6410")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= mini6410_map_io,
 	.init_machine	= mini6410_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-n30.c b/arch/arm/mach-s3c/mach-n30.c
index 998ccff3c174..e40c1fcf418c 100644
--- a/arch/arm/mach-s3c24xx/mach-n30.c
+++ b/arch/arm/mach-s3c/mach-n30.c
@@ -27,15 +27,15 @@
 #include <linux/io.h>
 #include <linux/mmc/host.h>
 
-#include <mach/hardware.h>
+#include "hardware-s3c24xx.h"
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
@@ -43,14 +43,12 @@
 
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
+#include "cpu.h"
+#include "devs.h"
 #include <linux/platform_data/mmc-s3cmci.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct map_desc n30_iodesc[] __initdata = {
 	/* nothing here yet */
@@ -368,6 +366,8 @@ static struct s3c2410fb_mach_info n30_fb_info __initdata = {
 
 static void n30_sdi_set_power(unsigned char power_mode, unsigned short vdd)
 {
+	s3c24xx_mci_def_set_power(power_mode, vdd);
+
 	switch (power_mode) {
 	case MMC_POWER_ON:
 	case MMC_POWER_UP:
@@ -389,10 +389,17 @@ static struct gpiod_lookup_table n30_mci_gpio_table = {
 	.dev_id = "s3c2410-sdi",
 	.table = {
 		/* Card detect S3C2410_GPF(1) */
-		GPIO_LOOKUP("GPF", 1, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOF", 1, "cd", GPIO_ACTIVE_LOW),
 		/* Write protect S3C2410_GPG(10) */
-		GPIO_LOOKUP("GPG", 10, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOG", 10, "wp", GPIO_ACTIVE_LOW),
 		{ },
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
 	},
 };
 
@@ -572,13 +579,13 @@ static void __init n30_map_io(void)
 	s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc));
 	n30_hwinit();
 	s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init n30_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 /* GPB3 is the line that controls the pull-up for the USB D+ line */
@@ -600,6 +607,10 @@ static void __init n30_init(void)
 			      S3C2410_MISCCR_USBSUSPND0 |
 			      S3C2410_MISCCR_USBSUSPND1, 0x0);
 
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
+
 	if (machine_is_n30()) {
 		/* Turn off suspend on both USB ports, and switch the
 		 * selectable USB port to USB device mode. */
diff --git a/arch/arm/mach-s3c64xx/mach-ncp.c b/arch/arm/mach-s3c/mach-ncp.c
index 13fea5c86ca3..1a45bed56622 100644
--- a/arch/arm/mach-s3c64xx/mach-ncp.c
+++ b/arch/arm/mach-s3c/mach-ncp.c
@@ -25,20 +25,18 @@
 #include <asm/mach/irq.h>
 
 #include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
+#include "fb.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE
@@ -81,7 +79,7 @@ static void __init ncp_map_io(void)
 	s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc));
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 }
 
 static void __init ncp_machine_init(void)
@@ -98,6 +96,5 @@ MACHINE_START(NCP, "NCP")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= ncp_map_io,
 	.init_machine	= ncp_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-nexcoder.c b/arch/arm/mach-s3c/mach-nexcoder.c
index c2f34758ccb6..2a454c919658 100644
--- a/arch/arm/mach-s3c24xx/mach-nexcoder.c
+++ b/arch/arm/mach-s3c/mach-nexcoder.c
@@ -28,21 +28,19 @@
 #include <asm/mach/irq.h>
 
 #include <asm/setup.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 //#include <asm/debug-ll.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct map_desc nexcoder_iodesc[] __initdata = {
 	/* nothing here yet */
@@ -131,7 +129,7 @@ static void __init nexcoder_map_io(void)
 {
 	s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc));
 	s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 
 	nexcoder_sensorboard_init();
 }
@@ -139,12 +137,17 @@ static void __init nexcoder_map_io(void)
 static void __init nexcoder_init_time(void)
 {
 	s3c2440_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init nexcoder_init(void)
 {
 	s3c_i2c0_set_platdata(NULL);
+
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
+
 	platform_add_devices(nexcoder_devices, ARRAY_SIZE(nexcoder_devices));
 };
 
diff --git a/arch/arm/mach-s3c24xx/mach-osiris-dvs.c b/arch/arm/mach-s3c/mach-osiris-dvs.c
index 5d819b6ea428..2e283aedab65 100644
--- a/arch/arm/mach-s3c24xx/mach-osiris-dvs.c
+++ b/arch/arm/mach-s3c/mach-osiris-dvs.c
@@ -14,8 +14,8 @@
 
 #include <linux/mfd/tps65010.h>
 
-#include <plat/cpu-freq.h>
-#include <mach/gpio-samsung.h>
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "gpio-samsung.h"
 
 #define OSIRIS_GPIO_DVS	S3C2410_GPB(5)
 
diff --git a/arch/arm/mach-s3c24xx/mach-osiris.c b/arch/arm/mach-s3c/mach-osiris.c
index 157448827f61..81744ca67d1d 100644
--- a/arch/arm/mach-s3c24xx/mach-osiris.c
+++ b/arch/arm/mach-s3c/mach-osiris.c
@@ -36,20 +36,17 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
-
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
-
-#include "common.h"
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-cpu-freq.h>
+#include "devs.h"
+#include "gpio-cfg.h"
+
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include "s3c24xx.h"
 #include "osiris.h"
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 /* onboard perihperal map */
 
@@ -359,7 +356,7 @@ static void __init osiris_map_io(void)
 
 	s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc));
 	s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 
 	/* check for the newer revision boards with large page nand */
 
@@ -384,7 +381,7 @@ static void __init osiris_map_io(void)
 static void __init osiris_init_time(void)
 {
 	s3c2440_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init osiris_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-otom.c b/arch/arm/mach-s3c/mach-otom.c
index 4e24d89e870b..460ee97766cd 100644
--- a/arch/arm/mach-s3c24xx/mach-otom.c
+++ b/arch/arm/mach-s3c/mach-otom.c
@@ -22,14 +22,13 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 #include "otom.h"
 
 static struct map_desc otom11_iodesc[] __initdata = {
@@ -95,18 +94,22 @@ static void __init otom11_map_io(void)
 {
 	s3c24xx_init_io(otom11_iodesc, ARRAY_SIZE(otom11_iodesc));
 	s3c24xx_init_uarts(otom11_uartcfgs, ARRAY_SIZE(otom11_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init otom11_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init otom11_init(void)
 {
 	s3c_i2c0_set_platdata(NULL);
+
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	platform_add_devices(otom11_devices, ARRAY_SIZE(otom11_devices));
 }
 
diff --git a/arch/arm/mach-s3c24xx/mach-qt2410.c b/arch/arm/mach-s3c/mach-qt2410.c
index f3131d94e90b..151e8e373d40 100644
--- a/arch/arm/mach-s3c24xx/mach-qt2410.c
+++ b/arch/arm/mach-s3c/mach-qt2410.c
@@ -28,26 +28,23 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/regs-lcd.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc qt2410_iodesc[] __initdata = {
 	{ 0xe0000000, __phys_to_pfn(S3C2410_CS3+0x01000000), SZ_1M, MT_DEVICE }
@@ -225,6 +222,20 @@ static struct gpiod_lookup_table qt2410_spi_gpiod_table = {
 	},
 };
 
+static struct gpiod_lookup_table qt2410_mmc_gpiod_table = {
+	.dev_id = "s3c2410-sdi",
+	.table = {
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /* Board devices */
 
 static struct platform_device *qt2410_devices[] __initdata = {
@@ -309,13 +320,13 @@ static void __init qt2410_map_io(void)
 {
 	s3c24xx_init_io(qt2410_iodesc, ARRAY_SIZE(qt2410_iodesc));
 	s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init qt2410_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init qt2410_machine_init(void)
@@ -343,9 +354,13 @@ static void __init qt2410_machine_init(void)
 	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
 
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	gpiod_add_lookup_table(&qt2410_spi_gpiod_table);
 	s3c_gpio_setpull(S3C2410_GPB(0), S3C_GPIO_PULL_NONE);
 	gpiod_add_lookup_table(&qt2410_led_gpio_table);
+	gpiod_add_lookup_table(&qt2410_mmc_gpiod_table);
 	platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
 	s3c_pm_init();
 }
diff --git a/arch/arm/mach-s3c64xx/mach-real6410.c b/arch/arm/mach-s3c/mach-real6410.c
index 1e98e530a6aa..9d218a53d631 100644
--- a/arch/arm/mach-s3c64xx/mach-real6410.c
+++ b/arch/arm/mach-s3c/mach-real6410.c
@@ -24,25 +24,24 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <mach/irqs.h>
 
-#include <plat/adc.h>
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
+#include <linux/soc/samsung/s3c-adc.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
 
 #include <video/platform_lcd.h>
 #include <video/samsung_fimd.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT
 #define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
@@ -208,7 +207,7 @@ static void __init real6410_map_io(void)
 	s3c64xx_init_io(NULL, 0);
 	s3c24xx_init_clocks(12000000);
 	s3c24xx_init_uarts(real6410_uartcfgs, ARRAY_SIZE(real6410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	/* set the LCD type */
 	tmp = __raw_readl(S3C64XX_SPCON);
@@ -330,6 +329,5 @@ MACHINE_START(REAL6410, "REAL6410")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= real6410_map_io,
 	.init_machine	= real6410_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-rx1950.c b/arch/arm/mach-s3c/mach-rx1950.c
index 3645b9c838d9..b9758f0a9a14 100644
--- a/arch/arm/mach-s3c24xx/mach-rx1950.c
+++ b/arch/arm/mach-s3c/mach-rx1950.c
@@ -42,21 +42,20 @@
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/fb-s3c2410.h>
 
 #include <sound/uda1380.h>
 
-#include <mach/fb.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
-#include <plat/gpio-cfg.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "gpio-cfg.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 #include "h1940.h"
 
 #define LCD_PWM_PERIOD 192960
@@ -361,14 +360,17 @@ static struct s3c2410fb_mach_info rx1950_lcd_cfg = {
 	.lpcsel = 0x02,
 	.gpccon = 0xaa9556a9,
 	.gpccon_mask = 0xffc003fc,
+	.gpccon_reg = S3C2410_GPCCON,
 	.gpcup = 0x0000ffff,
 	.gpcup_mask = 0xffffffff,
+	.gpcup_reg = S3C2410_GPCUP,
 
 	.gpdcon = 0xaa90aaa1,
 	.gpdcon_mask = 0xffc0fff0,
+	.gpdcon_reg = S3C2410_GPDCON,
 	.gpdup = 0x0000fcfd,
 	.gpdup_mask = 0xffffffff,
-
+	.gpdup_reg = S3C2410_GPDUP,
 };
 
 static struct pwm_lookup rx1950_pwm_lookup[] = {
@@ -549,6 +551,8 @@ static struct platform_device rx1950_backlight = {
 
 static void rx1950_set_mmc_power(unsigned char power_mode, unsigned short vdd)
 {
+	s3c24xx_mci_def_set_power(power_mode, vdd);
+
 	switch (power_mode) {
 	case MMC_POWER_OFF:
 		gpio_direction_output(S3C2410_GPJ(1), 0);
@@ -571,9 +575,16 @@ static struct gpiod_lookup_table rx1950_mmc_gpio_table = {
 	.dev_id = "s3c2410-sdi",
 	.table = {
 		/* Card detect S3C2410_GPF(5) */
-		GPIO_LOOKUP("GPF", 5, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOF", 5, "cd", GPIO_ACTIVE_LOW),
 		/* Write protect S3C2410_GPH(8) */
-		GPIO_LOOKUP("GPH", 8, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOH", 8, "wp", GPIO_ACTIVE_LOW),
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
 		{ },
 	},
 };
@@ -767,7 +778,7 @@ static void __init rx1950_map_io(void)
 {
 	s3c24xx_init_io(rx1950_iodesc, ARRAY_SIZE(rx1950_iodesc));
 	s3c24xx_init_uarts(rx1950_uartcfgs, ARRAY_SIZE(rx1950_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 
 	/* setup PM */
 
@@ -781,7 +792,7 @@ static void __init rx1950_map_io(void)
 static void __init rx1950_init_time(void)
 {
 	s3c2442_init_clocks(16934000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init rx1950_init_machine(void)
@@ -829,6 +840,9 @@ static void __init rx1950_init_machine(void)
 
 	pwm_add_table(rx1950_pwm_lookup, ARRAY_SIZE(rx1950_pwm_lookup));
 	gpiod_add_lookup_table(&rx1950_audio_gpio_table);
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	platform_add_devices(rx1950_devices, ARRAY_SIZE(rx1950_devices));
 
 	i2c_register_board_info(0, rx1950_i2c_devices,
diff --git a/arch/arm/mach-s3c24xx/mach-rx3715.c b/arch/arm/mach-s3c/mach-rx3715.c
index 017010d67e01..a03662a47b38 100644
--- a/arch/arm/mach-s3c24xx/mach-rx3715.c
+++ b/arch/arm/mach-s3c/mach-rx3715.c
@@ -30,22 +30,20 @@
 #include <asm/mach/map.h>
 
 #include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <linux/platform_data/fb-s3c2410.h>
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/fb.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 #include "h1940.h"
 
 static struct map_desc rx3715_iodesc[] __initdata = {
@@ -125,13 +123,17 @@ static struct s3c2410fb_mach_info rx3715_fb_info __initdata = {
 
 	.gpccon =	0xaa955699,
 	.gpccon_mask =	0xffc003cc,
+	.gpccon_reg =	S3C2410_GPCCON,
 	.gpcup =	0x0000ffff,
 	.gpcup_mask =	0xffffffff,
+	.gpcup_reg =	S3C2410_GPCUP,
 
 	.gpdcon =	0xaa95aaa1,
 	.gpdcon_mask =	0xffc0fff0,
+	.gpdcon_reg =	S3C2410_GPDCON,
 	.gpdup =	0x0000faff,
 	.gpdup_mask =	0xffffffff,
+	.gpdup_reg =	S3C2410_GPDUP,
 };
 
 static struct mtd_partition __initdata rx3715_nand_part[] = {
@@ -174,13 +176,13 @@ static void __init rx3715_map_io(void)
 {
 	s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc));
 	s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init rx3715_init_time(void)
 {
 	s3c2440_init_clocks(16934000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 /* H1940 and RX3715 need to reserve this for suspend */
@@ -199,6 +201,9 @@ static void __init rx3715_init_machine(void)
 
 	s3c_nand_set_platdata(&rx3715_nand_info);
 	s3c24xx_fb_set_platdata(&rx3715_fb_info);
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	platform_add_devices(rx3715_devices, ARRAY_SIZE(rx3715_devices));
 }
 
diff --git a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c b/arch/arm/mach-s3c/mach-s3c2416-dt.c
index aa7102713b37..418544d3015d 100644
--- a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
+++ b/arch/arm/mach-s3c/mach-s3c2416-dt.c
@@ -16,12 +16,12 @@
 #include <linux/serial_s3c.h>
 
 #include <asm/mach/arch.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static void __init s3c2416_dt_map_io(void)
 {
diff --git a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c b/arch/arm/mach-s3c/mach-s3c64xx-dt.c
index 1724f5ea5c46..00169c103862 100644
--- a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c
+++ b/arch/arm/mach-s3c/mach-s3c64xx-dt.c
@@ -8,11 +8,10 @@
 #include <asm/mach/map.h>
 #include <asm/system_misc.h>
 
-#include <plat/cpu.h>
-#include <mach/map.h>
+#include "cpu.h"
+#include "map.h"
 
-#include "common.h"
-#include "watchdog-reset.h"
+#include "s3c64xx.h"
 
 /*
  * IO mapping for shared system controller IP.
@@ -39,20 +38,6 @@ static void __init s3c64xx_dt_map_io(void)
 		panic("SoC is not S3C64xx!");
 }
 
-static void __init s3c64xx_dt_init_machine(void)
-{
-	samsung_wdt_reset_of_init();
-}
-
-static void s3c64xx_dt_restart(enum reboot_mode mode, const char *cmd)
-{
-	if (mode != REBOOT_SOFT)
-		samsung_wdt_reset();
-
-	/* if all else fails, or mode was for soft, jump to 0 */
-	soft_restart(0);
-}
-
 static const char *const s3c64xx_dt_compat[] __initconst = {
 	"samsung,s3c6400",
 	"samsung,s3c6410",
@@ -63,6 +48,4 @@ DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)")
 	/* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */
 	.dt_compat	= s3c64xx_dt_compat,
 	.map_io		= s3c64xx_dt_map_io,
-	.init_machine	= s3c64xx_dt_init_machine,
-	.restart        = s3c64xx_dt_restart,
 MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.c b/arch/arm/mach-s3c/mach-smartq.c
index 5025db607c0f..5b6e7c2a85ef 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.c
+++ b/arch/arm/mach-s3c/mach-smartq.c
@@ -18,25 +18,24 @@
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
 
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
+#include "cpu.h"
+#include "devs.h"
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
+#include "gpio-cfg.h"
 #include <linux/platform_data/hwmon-s3c.h>
 #include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
 #include <linux/platform_data/touchscreen-s3c2410.h>
 
 #include <video/platform_lcd.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
+#include "s3c64xx.h"
 #include "mach-smartq.h"
-#include "regs-modem.h"
+#include "regs-modem-s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT
 #define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
@@ -384,7 +383,7 @@ void __init smartq_map_io(void)
 	s3c64xx_set_xtal_freq(12000000);
 	s3c64xx_set_xusbxti_freq(12000000);
 	s3c24xx_init_uarts(smartq_uartcfgs, ARRAY_SIZE(smartq_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	smartq_lcd_mode_set();
 }
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.h b/arch/arm/mach-s3c/mach-smartq.h
index f98132f4f430..f98132f4f430 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.h
+++ b/arch/arm/mach-s3c/mach-smartq.h
diff --git a/arch/arm/mach-s3c64xx/mach-smartq5.c b/arch/arm/mach-s3c/mach-smartq5.c
index 44e9edb144fa..8c940227e810 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq5.c
+++ b/arch/arm/mach-s3c/mach-smartq5.c
@@ -15,17 +15,16 @@
 
 #include <video/samsung_fimd.h>
 #include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
+#include "gpio-cfg.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 #include "mach-smartq.h"
 
 static struct gpio_led smartq5_leds[] = {
@@ -151,6 +150,5 @@ MACHINE_START(SMARTQ5, "SmartQ 5")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smartq_map_io,
 	.init_machine	= smartq5_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smartq7.c b/arch/arm/mach-s3c/mach-smartq7.c
index 815ee7d0b5e3..ab243969d6d0 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq7.c
+++ b/arch/arm/mach-s3c/mach-smartq7.c
@@ -15,17 +15,16 @@
 
 #include <video/samsung_fimd.h>
 #include <mach/irqs.h>
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
+#include "fb.h"
+#include "gpio-cfg.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 #include "mach-smartq.h"
 
 static struct gpio_led smartq7_leds[] = {
@@ -167,6 +166,5 @@ MACHINE_START(SMARTQ7, "SmartQ 7")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smartq_map_io,
 	.init_machine	= smartq7_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2410.c b/arch/arm/mach-s3c/mach-smdk2410.c
index 18dfef52c8bf..ca83d5a7d101 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2410.c
+++ b/arch/arm/mach-s3c/mach-smdk2410.c
@@ -19,23 +19,23 @@
 #include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc smdk2410_iodesc[] __initdata = {
   /* nothing here yet */
@@ -81,19 +81,22 @@ static void __init smdk2410_map_io(void)
 {
 	s3c24xx_init_io(smdk2410_iodesc, ARRAY_SIZE(smdk2410_iodesc));
 	s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init smdk2410_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init smdk2410_init(void)
 {
 	s3c_i2c0_set_platdata(NULL);
 	platform_add_devices(smdk2410_devices, ARRAY_SIZE(smdk2410_devices));
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	smdk_machine_init();
 }
 
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2413.c b/arch/arm/mach-s3c/mach-smdk2413.c
index ca80167f268d..c43095b321d7 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2413.c
+++ b/arch/arm/mach-s3c/mach-smdk2413.c
@@ -23,27 +23,26 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/hardware/iomd.h>
 #include <asm/setup.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 //#include <asm/debug-ll.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
 
 #include <linux/platform_data/usb-s3c2410_udc.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc smdk2413_iodesc[] __initdata = {
 };
@@ -99,13 +98,13 @@ static void __init smdk2413_map_io(void)
 {
 	s3c24xx_init_io(smdk2413_iodesc, ARRAY_SIZE(smdk2413_iodesc));
 	s3c24xx_init_uarts(smdk2413_uartcfgs, ARRAY_SIZE(smdk2413_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init smdk2413_init_time(void)
 {
 	s3c2412_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init smdk2413_machine_init(void)
@@ -119,6 +118,9 @@ static void __init smdk2413_machine_init(void)
 
  	s3c24xx_udc_set_platdata(&smdk2413_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 
 	platform_add_devices(smdk2413_devices, ARRAY_SIZE(smdk2413_devices));
 	smdk_machine_init();
@@ -132,7 +134,7 @@ MACHINE_START(S3C2413, "S3C2413")
 	.init_irq	= s3c2412_init_irq,
 	.map_io		= smdk2413_map_io,
 	.init_machine	= smdk2413_machine_init,
-	.init_time	= samsung_timer_init,
+	.init_time	= s3c24xx_timer_init,
 MACHINE_END
 
 MACHINE_START(SMDK2412, "SMDK2412")
@@ -143,7 +145,7 @@ MACHINE_START(SMDK2412, "SMDK2412")
 	.init_irq	= s3c2412_init_irq,
 	.map_io		= smdk2413_map_io,
 	.init_machine	= smdk2413_machine_init,
-	.init_time	= samsung_timer_init,
+	.init_time	= s3c24xx_timer_init,
 MACHINE_END
 
 MACHINE_START(SMDK2413, "SMDK2413")
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2416.c b/arch/arm/mach-s3c/mach-smdk2416.c
index 61c3e45898d3..4d883a792cc6 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2416.c
+++ b/arch/arm/mach-s3c/mach-smdk2416.c
@@ -25,31 +25,29 @@
 #include <asm/mach/irq.h>
 
 #include <video/samsung_fimd.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/gpio-samsung.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
+#include "regs-s3c2443-clock.h"
+#include "gpio-samsung.h"
 
 #include <linux/platform_data/leds-s3c24xx.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "gpio-cfg.h"
+#include "devs.h"
+#include "cpu.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/sdhci.h>
+#include "sdhci.h"
 #include <linux/platform_data/usb-s3c2410_udc.h>
 #include <linux/platform_data/s3c-hsudc.h>
-#include <plat/samsung-time.h>
 
-#include <plat/fb.h>
+#include "fb.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc smdk2416_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
@@ -215,14 +213,14 @@ static struct platform_device *smdk2416_devices[] __initdata = {
 static void __init smdk2416_init_time(void)
 {
 	s3c2416_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init smdk2416_map_io(void)
 {
 	s3c24xx_init_io(smdk2416_iodesc, ARRAY_SIZE(smdk2416_iodesc));
 	s3c24xx_init_uarts(smdk2416_uartcfgs, ARRAY_SIZE(smdk2416_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init smdk2416_machine_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2440.c b/arch/arm/mach-s3c/mach-smdk2440.c
index 7bafcd8ea104..7f6fe0db04f3 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2440.c
+++ b/arch/arm/mach-s3c/mach-smdk2440.c
@@ -23,22 +23,21 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc smdk2440_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
@@ -137,6 +136,11 @@ static struct s3c2410fb_mach_info smdk2440_fb_info __initdata = {
 	.gpdcon_mask	= 0xffffffff,
 	.gpdup		= 0x0000faff,
 	.gpdup_mask	= 0xffffffff,
+
+	.gpccon_reg	= S3C2410_GPCCON,
+	.gpcup_reg	= S3C2410_GPCUP,
+	.gpdcon_reg	= S3C2410_GPDCON,
+	.gpdup_reg	= S3C2410_GPDUP,
 #endif
 
 	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
@@ -154,20 +158,22 @@ static void __init smdk2440_map_io(void)
 {
 	s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc));
 	s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init smdk2440_init_time(void)
 {
 	s3c2440_init_clocks(16934400);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init smdk2440_machine_init(void)
 {
 	s3c24xx_fb_set_platdata(&smdk2440_fb_info);
 	s3c_i2c0_set_platdata(NULL);
-
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	platform_add_devices(smdk2440_devices, ARRAY_SIZE(smdk2440_devices));
 	smdk_machine_init();
 }
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2443.c b/arch/arm/mach-s3c/mach-smdk2443.c
index 2358ed5ed7be..fc54c91ade56 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2443.c
+++ b/arch/arm/mach-s3c/mach-smdk2443.c
@@ -22,22 +22,19 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
 
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
-#include "common-smdk.h"
+#include "s3c24xx.h"
+#include "common-smdk-s3c24xx.h"
 
 static struct map_desc smdk2443_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
@@ -112,13 +109,13 @@ static void __init smdk2443_map_io(void)
 {
 	s3c24xx_init_io(smdk2443_iodesc, ARRAY_SIZE(smdk2443_iodesc));
 	s3c24xx_init_uarts(smdk2443_uartcfgs, ARRAY_SIZE(smdk2443_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init smdk2443_init_time(void)
 {
 	s3c2443_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init smdk2443_machine_init(void)
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6400.c b/arch/arm/mach-s3c/mach-smdk6400.c
index cbd16843c7d1..827221398d6c 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6400.c
+++ b/arch/arm/mach-s3c/mach-smdk6400.c
@@ -23,16 +23,14 @@
 #include <asm/mach/irq.h>
 
 #include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/gpio-samsung.h>
-#include <plat/samsung-time.h>
+#include "gpio-samsung.h"
 
-#include "common.h"
+#include "s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
@@ -62,7 +60,7 @@ static void __init smdk6400_map_io(void)
 	s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc));
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 }
 
 static struct platform_device *smdk6400_devices[] __initdata = {
@@ -88,6 +86,5 @@ MACHINE_START(SMDK6400, "SMDK6400")
 	.init_irq	= s3c6400_init_irq,
 	.map_io		= smdk6400_map_io,
 	.init_machine	= smdk6400_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c/mach-smdk6410.c
index 56f406c0c3dd..ae18c1375c9c 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c/mach-smdk6410.c
@@ -45,32 +45,30 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 #include <linux/platform_data/ata-samsung_cf.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
+#include "fb.h"
+#include "gpio-cfg.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc.h>
+#include "devs.h"
+#include "cpu.h"
+#include <linux/soc/samsung/s3c-adc.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
-#include <plat/keypad.h>
-#include <plat/samsung-time.h>
+#include "keypad.h"
 
-#include "backlight.h"
-#include "common.h"
-#include "regs-modem.h"
-#include "regs-srom.h"
-#include "regs-sys.h"
+#include "backlight-s3c64xx.h"
+#include "s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-srom-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
 
 #define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
@@ -635,7 +633,7 @@ static void __init smdk6410_map_io(void)
 	s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
 	s3c64xx_set_xtal_freq(12000000);
 	s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c64xx_set_timer_source(S3C64XX_PWM3, S3C64XX_PWM4);
 
 	/* set the LCD type */
 
@@ -704,6 +702,5 @@ MACHINE_START(SMDK6410, "SMDK6410")
 	.init_irq	= s3c6410_init_irq,
 	.map_io		= smdk6410_map_io,
 	.init_machine	= smdk6410_machine_init,
-	.init_time	= samsung_timer_init,
-	.restart	= s3c64xx_restart,
+	.init_time	= s3c64xx_timer_init,
 MACHINE_END
diff --git a/arch/arm/mach-s3c24xx/mach-tct_hammer.c b/arch/arm/mach-s3c/mach-tct_hammer.c
index 8d8ddd6ea305..2a61df316e8c 100644
--- a/arch/arm/mach-s3c24xx/mach-tct_hammer.c
+++ b/arch/arm/mach-s3c/mach-tct_hammer.c
@@ -7,6 +7,7 @@
 // derived from linux/arch/arm/mach-s3c2410/mach-bast.c, written by
 // Ben Dooks <ben@simtec.co.uk>
 
+#include <linux/gpio/machine.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -24,21 +25,19 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/flash.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
+#include "devs.h"
+#include "cpu.h"
 
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/map.h>
 #include <linux/mtd/physmap.h>
-#include <plat/samsung-time.h>
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct resource tct_hammer_nor_resource =
 			DEFINE_RES_MEM(0x00000000, SZ_16M);
@@ -103,6 +102,19 @@ static struct s3c2410_uartcfg tct_hammer_uartcfgs[] = {
 	}
 };
 
+static struct gpiod_lookup_table tct_hammer_mmc_gpio_table = {
+	.dev_id = "s3c2410-sdi",
+	.table = {
+		/* bus pins */
+		GPIO_LOOKUP_IDX("GPIOE",  5, "bus", 0, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  6, "bus", 1, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  7, "bus", 2, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  8, "bus", 3, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE",  9, "bus", 4, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("GPIOE", 10, "bus", 5, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 static struct platform_device *tct_hammer_devices[] __initdata = {
 	&s3c_device_adc,
@@ -119,18 +131,19 @@ static void __init tct_hammer_map_io(void)
 {
 	s3c24xx_init_io(tct_hammer_iodesc, ARRAY_SIZE(tct_hammer_iodesc));
 	s3c24xx_init_uarts(tct_hammer_uartcfgs, ARRAY_SIZE(tct_hammer_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init tct_hammer_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init tct_hammer_init(void)
 {
 	s3c_i2c0_set_platdata(NULL);
+	gpiod_add_lookup_table(&tct_hammer_mmc_gpio_table);
 	platform_add_devices(tct_hammer_devices, ARRAY_SIZE(tct_hammer_devices));
 }
 
diff --git a/arch/arm/mach-s3c24xx/mach-vr1000.c b/arch/arm/mach-s3c/mach-vr1000.c
index 6a3fb2becc7c..5c3d07cf2e79 100644
--- a/arch/arm/mach-s3c24xx/mach-vr1000.c
+++ b/arch/arm/mach-s3c/mach-vr1000.c
@@ -35,17 +35,15 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <linux/platform_data/asoc-s3c24xx_simtec.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/gpio-cfg.h>
-#include <plat/samsung-time.h>
+#include "cpu.h"
+#include "devs.h"
 
 #include "bast.h"
-#include "common.h"
+#include "s3c24xx.h"
 #include "simtec.h"
 #include "vr1000.h"
 
@@ -328,13 +326,13 @@ static void __init vr1000_map_io(void)
 
 	s3c24xx_init_io(vr1000_iodesc, ARRAY_SIZE(vr1000_iodesc));
 	s3c24xx_init_uarts(vr1000_uartcfgs, ARRAY_SIZE(vr1000_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init vr1000_init_time(void)
 {
 	s3c2410_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init vr1000_init(void)
diff --git a/arch/arm/mach-s3c24xx/mach-vstms.c b/arch/arm/mach-s3c/mach-vstms.c
index c5fa215a527e..05f19f5ffabb 100644
--- a/arch/arm/mach-s3c24xx/mach-vstms.c
+++ b/arch/arm/mach-s3c/mach-vstms.c
@@ -24,24 +24,23 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/setup.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-lcd.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
-#include <mach/fb.h>
+#include <linux/platform_data/fb-s3c2410.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/samsung-time.h>
+#include "devs.h"
+#include "cpu.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct map_desc vstms_iodesc[] __initdata = {
 };
@@ -136,20 +135,22 @@ static void __init vstms_map_io(void)
 {
 	s3c24xx_init_io(vstms_iodesc, ARRAY_SIZE(vstms_iodesc));
 	s3c24xx_init_uarts(vstms_uartcfgs, ARRAY_SIZE(vstms_uartcfgs));
-	samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4);
+	s3c24xx_set_timer_source(S3C24XX_PWM3, S3C24XX_PWM4);
 }
 
 static void __init vstms_init_time(void)
 {
 	s3c2412_init_clocks(12000000);
-	samsung_timer_init();
+	s3c24xx_timer_init();
 }
 
 static void __init vstms_init(void)
 {
 	s3c_i2c0_set_platdata(NULL);
 	s3c_nand_set_platdata(&vstms_nand_info);
-
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
 	platform_add_devices(vstms_devices, ARRAY_SIZE(vstms_devices));
 }
 
diff --git a/arch/arm/plat-samsung/include/plat/map-s3c.h b/arch/arm/mach-s3c/map-s3c.h
index 4244acbf4b65..a18fdd3d6ae2 100644
--- a/arch/arm/plat-samsung/include/plat/map-s3c.h
+++ b/arch/arm/mach-s3c/map-s3c.h
@@ -9,6 +9,8 @@
 #ifndef __ASM_PLAT_MAP_S3C_H
 #define __ASM_PLAT_MAP_S3C_H __FILE__
 
+#include "map.h"
+
 #define S3C24XX_VA_IRQ		S3C_VA_IRQ
 #define S3C24XX_VA_MEMCTRL	S3C_VA_MEM
 #define S3C24XX_VA_UART		S3C_VA_UART
@@ -45,16 +47,8 @@
 
 #define S3C_VA_USB_HSPHY	S3C64XX_VA_USB_HSPHY
 
-/*
- * ISA style IO, for each machine to sort out mappings for,
- * if it implements it. We reserve two 16M regions for ISA.
- */
-
 #define S3C2410_ADDR(x)		S3C_ADDR(x)
 
-#define S3C24XX_VA_ISA_WORD	S3C2410_ADDR(0x02000000)
-#define S3C24XX_VA_ISA_BYTE	S3C2410_ADDR(0x03000000)
-
 /* deal with the registers that move under the 2412/2413 */
 
 #if defined(CONFIG_CPU_S3C2412)
@@ -71,6 +65,6 @@ extern void __iomem *s3c24xx_va_gpio2;
 #define S3C24XX_VA_GPIO2 S3C24XX_VA_GPIO
 #endif
 
-#include <plat/map-s5p.h>
+#include "map-s5p.h"
 
 #endif /* __ASM_PLAT_MAP_S3C_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/map.h b/arch/arm/mach-s3c/map-s3c24xx.h
index bca93112f57d..b5dba78a9dd7 100644
--- a/arch/arm/mach-s3c24xx/include/mach/map.h
+++ b/arch/arm/mach-s3c/map-s3c24xx.h
@@ -9,8 +9,8 @@
 #ifndef __ASM_ARCH_MAP_H
 #define __ASM_ARCH_MAP_H
 
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
+#include <mach/map-base.h>
+#include "map-s3c.h"
 
 /*
  * interrupt controller is the first thing we put in, to make
@@ -86,6 +86,8 @@
 #define S3C2410_PA_SPI	   (0x59000000)
 #define S3C2443_PA_SPI0		(0x52000000)
 #define S3C2443_PA_SPI1		S3C2410_PA_SPI
+#define S3C2410_SPI1		(0x20)
+#define S3C2412_SPI1		(0x100)
 
 /* SDI */
 #define S3C2410_PA_SDI	   (0x5A000000)
diff --git a/arch/arm/mach-s3c64xx/include/mach/map.h b/arch/arm/mach-s3c/map-s3c64xx.h
index 9372a535b7ba..d7740d2a77c4 100644
--- a/arch/arm/mach-s3c64xx/include/mach/map.h
+++ b/arch/arm/mach-s3c/map-s3c64xx.h
@@ -11,8 +11,8 @@
 #ifndef __ASM_ARCH_MAP_H
 #define __ASM_ARCH_MAP_H __FILE__
 
-#include <plat/map-base.h>
-#include <plat/map-s3c.h>
+#include <mach/map-base.h>
+#include "map-s3c.h"
 
 /*
  * Post-mux Chip Select Regions Xm0CSn_
diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/mach-s3c/map-s5p.h
index d69a0ca09fb5..cd237924e34d 100644
--- a/arch/arm/plat-samsung/include/plat/map-s5p.h
+++ b/arch/arm/mach-s3c/map-s5p.h
@@ -9,14 +9,12 @@
 #ifndef __ASM_PLAT_MAP_S5P_H
 #define __ASM_PLAT_MAP_S5P_H __FILE__
 
-#define S5P_VA_CHIPID		S3C_ADDR(0x02000000)
-
 #define VA_VIC(x)		(S3C_VA_IRQ + ((x) * 0x10000))
 #define VA_VIC0			VA_VIC(0)
 #define VA_VIC1			VA_VIC(1)
 #define VA_VIC2			VA_VIC(2)
 #define VA_VIC3			VA_VIC(3)
 
-#include <plat/map-s3c.h>
+#include "map-s3c.h"
 
 #endif /* __ASM_PLAT_MAP_S5P_H */
diff --git a/arch/arm/mach-s3c/map.h b/arch/arm/mach-s3c/map.h
new file mode 100644
index 000000000000..7cfb517d4886
--- /dev/null
+++ b/arch/arm/mach-s3c/map.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "map-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "map-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/nand-core.h b/arch/arm/mach-s3c/nand-core-s3c24xx.h
index 8de633d416ae..a14316729c48 100644
--- a/arch/arm/mach-s3c24xx/nand-core.h
+++ b/arch/arm/mach-s3c/nand-core-s3c24xx.h
@@ -6,8 +6,8 @@
  * S3C -  Nand Controller core functions
  */
 
-#ifndef __ASM_ARCH_NAND_CORE_H
-#define __ASM_ARCH_NAND_CORE_H __FILE__
+#ifndef __ASM_ARCH_NAND_CORE_S3C24XX_H
+#define __ASM_ARCH_NAND_CORE_S3C24XX_H __FILE__
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
@@ -21,4 +21,4 @@ static inline void s3c_nand_setname(char *name)
 #endif
 }
 
-#endif /* __ASM_ARCH_NAND_CORE_H */
+#endif /* __ASM_ARCH_NAND_CORE_S3C24XX_H */
diff --git a/arch/arm/mach-s3c64xx/onenand-core.h b/arch/arm/mach-s3c/onenand-core-s3c64xx.h
index 0cf6b5e76b24..e2dfdd1fec93 100644
--- a/arch/arm/mach-s3c64xx/onenand-core.h
+++ b/arch/arm/mach-s3c/onenand-core-s3c64xx.h
@@ -7,8 +7,8 @@
  * Samsung OneNAD Controller core functions
  */
 
-#ifndef __ASM_ARCH_ONENAND_CORE_H
-#define __ASM_ARCH_ONENAND_CORE_H __FILE__
+#ifndef __ASM_ARCH_ONENAND_CORE_S3C64XX_H
+#define __ASM_ARCH_ONENAND_CORE_S3C64XX_H __FILE__
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
@@ -29,4 +29,4 @@ static inline void s3c64xx_onenand1_setname(char *name)
 #endif
 }
 
-#endif /* __ASM_ARCH_ONENAND_CORE_H */
+#endif /* __ASM_ARCH_ONENAND_CORE_S3C64XX_H */
diff --git a/arch/arm/mach-s3c24xx/osiris.h b/arch/arm/mach-s3c/osiris.h
index b6c9c5ed2ba7..b6c9c5ed2ba7 100644
--- a/arch/arm/mach-s3c24xx/osiris.h
+++ b/arch/arm/mach-s3c/osiris.h
diff --git a/arch/arm/mach-s3c24xx/otom.h b/arch/arm/mach-s3c/otom.h
index c800f67d03d4..c800f67d03d4 100644
--- a/arch/arm/mach-s3c24xx/otom.h
+++ b/arch/arm/mach-s3c/otom.h
diff --git a/arch/arm/mach-s3c64xx/pl080.c b/arch/arm/mach-s3c/pl080.c
index 152edbeea0c7..4730f080c736 100644
--- a/arch/arm/mach-s3c64xx/pl080.c
+++ b/arch/arm/mach-s3c/pl080.c
@@ -10,11 +10,11 @@
 #include <linux/amba/pl08x.h>
 #include <linux/of.h>
 
-#include <plat/cpu.h>
+#include "cpu.h"
 #include <mach/irqs.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include "regs-sys.h"
+#include "regs-sys-s3c64xx.h"
 
 static int pl08x_get_xfer_signal(const struct pl08x_channel_data *cd)
 {
diff --git a/arch/arm/plat-samsung/platformdata.c b/arch/arm/mach-s3c/platformdata.c
index cbc3b4b45c74..e643c81aef45 100644
--- a/arch/arm/plat-samsung/platformdata.c
+++ b/arch/arm/mach-s3c/platformdata.c
@@ -9,8 +9,8 @@
 #include <linux/string.h>
 #include <linux/platform_device.h>
 
-#include <plat/devs.h>
-#include <plat/sdhci.h>
+#include "devs.h"
+#include "sdhci.h"
 
 void __init *s3c_set_platdata(void *pd, size_t pdsize,
 			      struct platform_device *pdev)
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2410.c b/arch/arm/mach-s3c/pll-s3c2410.c
index 0561f79ddce8..3fbc99eaa4a2 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2410.c
+++ b/arch/arm/mach-s3c/pll-s3c2410.c
@@ -15,8 +15,8 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
 
 /* This array should be sorted in ascending order of the frequencies */
 static struct cpufreq_frequency_table pll_vals_12MHz[] = {
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c b/arch/arm/mach-s3c/pll-s3c2440-12000000.c
index 2ec3a2f9a6a5..fdb8e8c2fe3b 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
+++ b/arch/arm/mach-s3c/pll-s3c2440-12000000.c
@@ -13,8 +13,8 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
 
 /* This array should be sorted in ascending order of the frequencies */
 static struct cpufreq_frequency_table s3c2440_plls_12[] = {
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c b/arch/arm/mach-s3c/pll-s3c2440-16934400.c
index 4b3d9e36c6bb..438b6fc099a4 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
+++ b/arch/arm/mach-s3c/pll-s3c2440-16934400.c
@@ -13,8 +13,8 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
+#include <linux/soc/samsung/s3c-cpufreq-core.h>
+#include <linux/soc/samsung/s3c-pm.h>
 
 /* This array should be sorted in ascending order of the frequencies */
 static struct cpufreq_frequency_table s3c2440_plls_169344[] = {
diff --git a/arch/arm/plat-samsung/pm-common.c b/arch/arm/mach-s3c/pm-common.c
index 59a10c6dcba1..618bd4499cae 100644
--- a/arch/arm/plat-samsung/pm-common.c
+++ b/arch/arm/mach-s3c/pm-common.c
@@ -12,7 +12,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 
-#include <plat/pm-common.h>
+#include "pm-common.h"
 
 /* helper functions to save and restore register state */
 
@@ -55,6 +55,8 @@ void s3c_pm_do_restore(const struct sleep_save *ptr, int count)
 
 /**
  * s3c_pm_do_restore_core() - early restore register values from save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
  *
  * This is similar to s3c_pm_do_restore() except we try and minimise the
  * side effects of the function in case registers that hardware might need
diff --git a/arch/arm/mach-s3c/pm-common.h b/arch/arm/mach-s3c/pm-common.h
new file mode 100644
index 000000000000..18b9607e1e39
--- /dev/null
+++ b/arch/arm/mach-s3c/pm-common.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *	Tomasz Figa <t.figa@samsung.com>
+ * Copyright (c) 2004 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Written by Ben Dooks, <ben@simtec.co.uk>
+ */
+
+#ifndef __PLAT_SAMSUNG_PM_COMMON_H
+#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
+
+#include <linux/irq.h>
+#include <linux/soc/samsung/s3c-pm.h>
+
+/* sleep save info */
+
+/**
+ * struct sleep_save - save information for shared peripherals.
+ * @reg: Pointer to the register to save.
+ * @val: Holder for the value saved from reg.
+ *
+ * This describes a list of registers which is used by the pm core and
+ * other subsystem to save and restore register values over suspend.
+ */
+struct sleep_save {
+	void __iomem	*reg;
+	unsigned long	val;
+};
+
+#define SAVE_ITEM(x) \
+	{ .reg = (x) }
+
+/* helper functions to save/restore lists of registers. */
+
+extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
+
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/pm-core.h b/arch/arm/mach-s3c/pm-core-s3c24xx.h
index 5e4ce89d0158..bcb7978a4e85 100644
--- a/arch/arm/mach-s3c24xx/include/mach/pm-core.h
+++ b/arch/arm/mach-s3c/pm-core-s3c24xx.h
@@ -11,10 +11,12 @@
 #include <linux/io.h>
 
 #include "regs-clock.h"
-#include "regs-irq.h"
+#include "regs-irq-s3c24xx.h"
+#include <mach/irqs.h>
 
 static inline void s3c_pm_debug_init_uart(void)
 {
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
 	unsigned long tmp = __raw_readl(S3C2410_CLKCON);
 
 	/* re-start uart clocks */
@@ -24,6 +26,7 @@ static inline void s3c_pm_debug_init_uart(void)
 
 	__raw_writel(tmp, S3C2410_CLKCON);
 	udelay(10);
+#endif
 }
 
 static inline void s3c_pm_arch_prepare_irqs(void)
@@ -75,11 +78,6 @@ static inline void s3c_pm_arch_show_resume_irqs(void)
 				s3c_irqwake_eintmask);
 }
 
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
-					   struct pm_uart_save *save)
-{
-}
-
 static inline void s3c_pm_restored_gpios(void) { }
 static inline void samsung_pm_saved_gpios(void) { }
 
diff --git a/arch/arm/mach-s3c64xx/include/mach/pm-core.h b/arch/arm/mach-s3c/pm-core-s3c64xx.h
index bbf79ed28583..06f564e5cf63 100644
--- a/arch/arm/mach-s3c64xx/include/mach/pm-core.h
+++ b/arch/arm/mach-s3c/pm-core-s3c64xx.h
@@ -14,12 +14,13 @@
 #include <linux/serial_s3c.h>
 #include <linux/delay.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
-#include <mach/map.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
+#include "map.h"
 
 static inline void s3c_pm_debug_init_uart(void)
 {
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
 	u32 tmp = __raw_readl(S3C_PCLK_GATE);
 
 	/* As a note, since the S3C64XX UARTs generally have multiple
@@ -35,6 +36,7 @@ static inline void s3c_pm_debug_init_uart(void)
 
 	__raw_writel(tmp, S3C_PCLK_GATE);
 	udelay(10);
+#endif
 }
 
 static inline void s3c_pm_arch_prepare_irqs(void)
@@ -63,48 +65,6 @@ static inline void s3c_pm_arch_show_resume_irqs(void)
 #define s3c_irqwake_intallow  0
 #endif
 
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
-					   struct pm_uart_save *save)
-{
-	u32 ucon = __raw_readl(regs + S3C2410_UCON);
-	u32 ucon_clk = ucon & S3C6400_UCON_CLKMASK;
-	u32 save_clk = save->ucon & S3C6400_UCON_CLKMASK;
-	u32 new_ucon;
-	u32 delta;
-
-	/* S3C64XX UART blocks only support level interrupts, so ensure that
-	 * when we restore unused UART blocks we force the level interrupt
-	 * settigs. */
-	save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
-
-	/* We have a constraint on changing the clock type of the UART
-	 * between UCLKx and PCLK, so ensure that when we restore UCON
-	 * that the CLK field is correctly modified if the bootloader
-	 * has changed anything.
-	 */
-	if (ucon_clk != save_clk) {
-		new_ucon = save->ucon;
-		delta = ucon_clk ^ save_clk;
-
-		/* change from UCLKx => wrong PCLK,
-		 * either UCLK can be tested for by a bit-test
-		 * with UCLK0 */
-		if (ucon_clk & S3C6400_UCON_UCLK0 &&
-		    !(save_clk & S3C6400_UCON_UCLK0) &&
-		    delta & S3C6400_UCON_PCLK2) {
-			new_ucon &= ~S3C6400_UCON_UCLK0;
-		} else if (delta == S3C6400_UCON_PCLK2) {
-			/* as an precaution, don't change from
-			 * PCLK2 => PCLK or vice-versa */
-			new_ucon ^= S3C6400_UCON_PCLK2;
-		}
-
-		S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
-			  ucon, new_ucon, save->ucon);
-		save->ucon = new_ucon;
-	}
-}
-
 static inline void s3c_pm_restored_gpios(void)
 {
 	/* ensure sleep mode has been cleared from the system */
diff --git a/arch/arm/mach-s3c/pm-core.h b/arch/arm/mach-s3c/pm-core.h
new file mode 100644
index 000000000000..b0e1d277f599
--- /dev/null
+++ b/arch/arm/mach-s3c/pm-core.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "pm-core-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "pm-core-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/pm-gpio.c b/arch/arm/mach-s3c/pm-gpio.c
index cb2e3bc79336..cfdbc2337998 100644
--- a/arch/arm/plat-samsung/pm-gpio.c
+++ b/arch/arm/mach-s3c/pm-gpio.c
@@ -13,10 +13,10 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
 
-#include <plat/gpio-core.h>
-#include <plat/pm.h>
+#include "gpio-core.h"
+#include "pm.h"
 
 /* PM GPIO helpers */
 
diff --git a/arch/arm/mach-s3c24xx/pm-h1940.S b/arch/arm/mach-s3c/pm-h1940.S
index a7bbe336ac6b..3bf6685123cb 100644
--- a/arch/arm/mach-s3c24xx/pm-h1940.S
+++ b/arch/arm/mach-s3c/pm-h1940.S
@@ -7,10 +7,9 @@
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
 
 	.text
 	.global	h1940_pm_return
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2410.c b/arch/arm/mach-s3c/pm-s3c2410.c
index 2d8ea701380a..a66419883735 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2410.c
+++ b/arch/arm/mach-s3c/pm-s3c2410.c
@@ -16,13 +16,12 @@
 
 #include <asm/mach-types.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
-#include <plat/gpio-cfg.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "cpu.h"
+#include "pm.h"
 
 #include "h1940.h"
 
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2412.c b/arch/arm/mach-s3c/pm-s3c2412.c
index 2dfdaab0aa1f..6a9604477c9e 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2412.c
+++ b/arch/arm/mach-s3c/pm-s3c2412.c
@@ -19,14 +19,14 @@
 #include <asm/cacheflush.h>
 #include <asm/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include <mach/irqs.h>
+#include "regs-gpio.h"
 
-#include <plat/cpu.h>
-#include <plat/pm.h>
-#include <plat/wakeup-mask.h>
+#include "cpu.h"
+#include "pm.h"
+#include "wakeup-mask.h"
 
-#include "regs-dsc.h"
+#include "regs-dsc-s3c24xx.h"
 #include "s3c2412-power.h"
 
 extern void s3c2412_sleep_enter(void);
diff --git a/arch/arm/mach-s3c24xx/pm-s3c2416.c b/arch/arm/mach-s3c/pm-s3c2416.c
index 9a2f05e279d4..f69ad84cf4ff 100644
--- a/arch/arm/mach-s3c24xx/pm-s3c2416.c
+++ b/arch/arm/mach-s3c/pm-s3c2416.c
@@ -11,10 +11,10 @@
 
 #include <asm/cacheflush.h>
 
-#include <mach/regs-s3c2443-clock.h>
+#include "regs-s3c2443-clock.h"
 
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
 
 #include "s3c2412-power.h"
 
diff --git a/arch/arm/mach-s3c24xx/pm.c b/arch/arm/mach-s3c/pm-s3c24xx.c
index c64988c609ad..3a8f5c38882e 100644
--- a/arch/arm/mach-s3c24xx/pm.c
+++ b/arch/arm/mach-s3c/pm-s3c24xx.c
@@ -21,17 +21,17 @@
 #include <linux/serial_s3c.h>
 #include <linux/io.h>
 
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-irq.h>
-#include <mach/gpio-samsung.h>
+#include "regs-clock.h"
+#include "regs-gpio.h"
+#include "regs-irq.h"
+#include "gpio-samsung.h"
 
 #include <asm/mach/time.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/pm.h>
+#include "gpio-cfg.h"
+#include "pm.h"
 
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 #define PFX "s3c24xx-pm: "
 
diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c/pm-s3c64xx.c
index fd6dbb263ed5..4f1778123dee 100644
--- a/arch/arm/mach-s3c64xx/pm.c
+++ b/arch/arm/mach-s3c/pm-s3c64xx.c
@@ -14,22 +14,22 @@
 #include <linux/gpio.h>
 #include <linux/pm_domain.h>
 
-#include <mach/map.h>
+#include "map.h"
 #include <mach/irqs.h>
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/wakeup-mask.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "wakeup-mask.h"
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
-#include <mach/gpio-samsung.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
+#include "gpio-samsung.h"
 
-#include "regs-gpio-memport.h"
-#include "regs-modem.h"
-#include "regs-sys.h"
-#include "regs-syscon-power.h"
+#include "regs-gpio-memport-s3c64xx.h"
+#include "regs-modem-s3c64xx.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-syscon-power-s3c64xx.h"
 
 struct s3c64xx_pm_domain {
 	char *const name;
@@ -305,6 +305,56 @@ static void s3c64xx_pm_prepare(void)
 	__raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), S3C64XX_WAKEUP_STAT);
 }
 
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+void s3c_pm_arch_update_uart(void __iomem *regs, struct pm_uart_save *save)
+{
+	u32 ucon;
+	u32 ucon_clk
+	u32 save_clk;
+	u32 new_ucon;
+	u32 delta;
+
+	if (!soc_is_s3c64xx())
+		return;
+
+	ucon = __raw_readl(regs + S3C2410_UCON);
+	ucon_clk = ucon & S3C6400_UCON_CLKMASK;
+	sav_clk = save->ucon & S3C6400_UCON_CLKMASK;
+
+	/* S3C64XX UART blocks only support level interrupts, so ensure that
+	 * when we restore unused UART blocks we force the level interrupt
+	 * settigs. */
+	save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
+
+	/* We have a constraint on changing the clock type of the UART
+	 * between UCLKx and PCLK, so ensure that when we restore UCON
+	 * that the CLK field is correctly modified if the bootloader
+	 * has changed anything.
+	 */
+	if (ucon_clk != save_clk) {
+		new_ucon = save->ucon;
+		delta = ucon_clk ^ save_clk;
+
+		/* change from UCLKx => wrong PCLK,
+		 * either UCLK can be tested for by a bit-test
+		 * with UCLK0 */
+		if (ucon_clk & S3C6400_UCON_UCLK0 &&
+		    !(save_clk & S3C6400_UCON_UCLK0) &&
+		    delta & S3C6400_UCON_PCLK2) {
+			new_ucon &= ~S3C6400_UCON_UCLK0;
+		} else if (delta == S3C6400_UCON_PCLK2) {
+			/* as an precaution, don't change from
+			 * PCLK2 => PCLK or vice-versa */
+			new_ucon ^= S3C6400_UCON_PCLK2;
+		}
+
+		S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
+			  ucon, new_ucon, save->ucon);
+		save->ucon = new_ucon;
+	}
+}
+#endif
+
 int __init s3c64xx_pm_init(void)
 {
 	int i;
diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/mach-s3c/pm.c
index d6bfd66592b0..c563bb9d92be 100644
--- a/arch/arm/plat-samsung/pm.c
+++ b/arch/arm/mach-s3c/pm.c
@@ -18,15 +18,16 @@
 #include <asm/cacheflush.h>
 #include <asm/suspend.h>
 
-#include <mach/map.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-irq.h>
+#include "map.h"
+#include "regs-clock.h"
+#include "regs-irq.h"
 #include <mach/irqs.h>
 
 #include <asm/irq.h>
 
-#include <plat/pm.h>
-#include <mach/pm-core.h>
+#include "cpu.h"
+#include "pm.h"
+#include "pm-core.h"
 
 /* for external use */
 
@@ -70,8 +71,7 @@ static int s3c_pm_enter(suspend_state_t state)
 {
 	int ret;
 	/* ensure the debug is initialised (if enabled) */
-
-	s3c_pm_debug_init();
+	s3c_pm_debug_init_uart();
 
 	S3C_PMDBG("%s(%d)\n", __func__, state);
 
@@ -100,7 +100,7 @@ static int s3c_pm_enter(suspend_state_t state)
 		samsung_pm_saved_gpios();
 	}
 
-	s3c_pm_save_uarts();
+	s3c_pm_save_uarts(soc_is_s3c2410());
 	s3c_pm_save_core();
 
 	/* set the irq configuration for wake */
@@ -137,14 +137,14 @@ static int s3c_pm_enter(suspend_state_t state)
 	/* restore the system state */
 
 	s3c_pm_restore_core();
-	s3c_pm_restore_uarts();
+	s3c_pm_restore_uarts(soc_is_s3c2410());
 
 	if (!of_have_populated_dt()) {
 		samsung_pm_restore_gpios();
 		s3c_pm_restored_gpios();
 	}
 
-	s3c_pm_debug_init();
+	s3c_pm_debug_init_uart();
 
 	/* check what irq (if any) restored the system */
 
diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/mach-s3c/pm.h
index 2746137f9794..eed61e585457 100644
--- a/arch/arm/plat-samsung/include/plat/pm.h
+++ b/arch/arm/mach-s3c/pm.h
@@ -11,7 +11,7 @@
  * management
 */
 
-#include <plat/pm-common.h>
+#include "pm-common.h"
 
 struct device;
 
diff --git a/arch/arm/plat-samsung/include/plat/pwm-core.h b/arch/arm/mach-s3c/pwm-core.h
index 05e3448642a1..05e3448642a1 100644
--- a/arch/arm/plat-samsung/include/plat/pwm-core.h
+++ b/arch/arm/mach-s3c/pwm-core.h
diff --git a/arch/arm/plat-samsung/include/plat/regs-adc.h b/arch/arm/mach-s3c/regs-adc.h
index 58953c7381dd..58953c7381dd 100644
--- a/arch/arm/plat-samsung/include/plat/regs-adc.h
+++ b/arch/arm/mach-s3c/regs-adc.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h b/arch/arm/mach-s3c/regs-clock-s3c24xx.h
index 7ca3dd4f13c0..933ddb5eedec 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h
+++ b/arch/arm/mach-s3c/regs-clock-s3c24xx.h
@@ -9,6 +9,8 @@
 #ifndef __ASM_ARM_REGS_CLOCK
 #define __ASM_ARM_REGS_CLOCK
 
+#include "map.h"
+
 #define S3C2410_CLKREG(x) ((x) + S3C24XX_VA_CLKPWR)
 
 #define S3C2410_PLLVAL(_m,_p,_s) ((_m) << 12 | ((_p) << 4) | ((_s)))
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-clock.h b/arch/arm/mach-s3c/regs-clock-s3c64xx.h
index 35a68767b318..35a68767b318 100644
--- a/arch/arm/mach-s3c64xx/include/mach/regs-clock.h
+++ b/arch/arm/mach-s3c/regs-clock-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-clock.h b/arch/arm/mach-s3c/regs-clock.h
new file mode 100644
index 000000000000..7df31f203d28
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-clock.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-clock-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-clock-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/regs-dsc.h b/arch/arm/mach-s3c/regs-dsc-s3c24xx.h
index b500636276f2..8b8b572aef04 100644
--- a/arch/arm/mach-s3c24xx/regs-dsc.h
+++ b/arch/arm/mach-s3c/regs-dsc-s3c24xx.h
@@ -7,8 +7,8 @@
  */
 
 
-#ifndef __ASM_ARCH_REGS_DSC_H
-#define __ASM_ARCH_REGS_DSC_H __FILE__
+#ifndef __ASM_ARCH_REGS_DSC_S3C24XX_H
+#define __ASM_ARCH_REGS_DSC_S3C24XX_H __FILE__
 
 /* S3C2412 */
 #define S3C2412_DSC0	   S3C2410_GPIOREG(0xdc)
@@ -18,5 +18,5 @@
 #define S3C2440_DSC0	   S3C2410_GPIOREG(0xc4)
 #define S3C2440_DSC1	   S3C2410_GPIOREG(0xc8)
 
-#endif	/* __ASM_ARCH_REGS_DSC_H */
+#endif	/* __ASM_ARCH_REGS_DSC_S3C24XX_H */
 
diff --git a/arch/arm/mach-s3c64xx/regs-gpio-memport.h b/arch/arm/mach-s3c/regs-gpio-memport-s3c64xx.h
index 589afe1132d6..589afe1132d6 100644
--- a/arch/arm/mach-s3c64xx/regs-gpio-memport.h
+++ b/arch/arm/mach-s3c/regs-gpio-memport-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio-s3c24xx.h
index 594e967c0673..9a7e262268a7 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h
+++ b/arch/arm/mach-s3c/regs-gpio-s3c24xx.h
@@ -10,6 +10,8 @@
 #ifndef __ASM_ARCH_REGS_GPIO_H
 #define __ASM_ARCH_REGS_GPIO_H
 
+#include "map-s3c.h"
+
 #define S3C24XX_MISCCR		S3C24XX_GPIOREG2(0x80)
 
 /* general configuration options */
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio-s3c64xx.h
index 592a2be3d2aa..592a2be3d2aa 100644
--- a/arch/arm/mach-s3c64xx/include/mach/regs-gpio.h
+++ b/arch/arm/mach-s3c/regs-gpio-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-gpio.h b/arch/arm/mach-s3c/regs-gpio.h
new file mode 100644
index 000000000000..0d41cb76d440
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-gpio.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-gpio-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-gpio-s3c64xx.h"
+#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h b/arch/arm/mach-s3c/regs-irq-s3c24xx.h
index 8d8e669e3903..c0b97b203415 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-irq.h
+++ b/arch/arm/mach-s3c/regs-irq-s3c24xx.h
@@ -8,6 +8,8 @@
 #ifndef ___ASM_ARCH_REGS_IRQ_H
 #define ___ASM_ARCH_REGS_IRQ_H
 
+#include "map-s3c.h"
+
 /* interrupt controller */
 
 #define S3C2410_IRQREG(x)   ((x) + S3C24XX_VA_IRQ)
diff --git a/arch/arm/mach-s3c64xx/include/mach/regs-irq.h b/arch/arm/mach-s3c/regs-irq-s3c64xx.h
index b18c7bcb61c5..b18c7bcb61c5 100644
--- a/arch/arm/mach-s3c64xx/include/mach/regs-irq.h
+++ b/arch/arm/mach-s3c/regs-irq-s3c64xx.h
diff --git a/arch/arm/mach-s3c/regs-irq.h b/arch/arm/mach-s3c/regs-irq.h
new file mode 100644
index 000000000000..57f0dda8dbf5
--- /dev/null
+++ b/arch/arm/mach-s3c/regs-irq.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_ARCH_S3C24XX
+#include "regs-irq-s3c24xx.h"
+#endif
+
+#ifdef CONFIG_ARCH_S3C64XX
+#include "regs-irq-s3c64xx.h"
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/regs-irqtype.h b/arch/arm/mach-s3c/regs-irqtype.h
index ec5c4c5fdd8f..ec5c4c5fdd8f 100644
--- a/arch/arm/plat-samsung/include/plat/regs-irqtype.h
+++ b/arch/arm/mach-s3c/regs-irqtype.h
diff --git a/arch/arm/mach-s3c24xx/regs-mem.h b/arch/arm/mach-s3c/regs-mem-s3c24xx.h
index 2f3bc48b5890..8fed34a1672a 100644
--- a/arch/arm/mach-s3c24xx/regs-mem.h
+++ b/arch/arm/mach-s3c/regs-mem-s3c24xx.h
@@ -9,6 +9,8 @@
 #ifndef __ARCH_ARM_MACH_S3C24XX_REGS_MEM_H
 #define __ARCH_ARM_MACH_S3C24XX_REGS_MEM_H __FILE__
 
+#include "map-s3c.h"
+
 #define S3C2410_MEMREG(x)		(S3C24XX_VA_MEMCTRL + (x))
 
 #define S3C2410_BWSCON			S3C2410_MEMREG(0x00)
diff --git a/arch/arm/mach-s3c64xx/regs-modem.h b/arch/arm/mach-s3c/regs-modem-s3c64xx.h
index 136ad44291bf..136ad44291bf 100644
--- a/arch/arm/mach-s3c64xx/regs-modem.h
+++ b/arch/arm/mach-s3c/regs-modem-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h b/arch/arm/mach-s3c/regs-s3c2443-clock.h
index 6bf924612b06..b3b670d463db 100644
--- a/arch/arm/mach-s3c24xx/include/mach/regs-s3c2443-clock.h
+++ b/arch/arm/mach-s3c/regs-s3c2443-clock.h
@@ -10,6 +10,9 @@
 #ifndef __ASM_ARM_REGS_S3C2443_CLOCK
 #define __ASM_ARM_REGS_S3C2443_CLOCK
 
+#include <linux/delay.h>
+#include "map-s3c.h"
+
 #define S3C2443_CLKREG(x)		((x) + S3C24XX_VA_CLKPWR)
 
 #define S3C2443_PLLCON_MDIVSHIFT	16
@@ -184,5 +187,52 @@ s3c2443_get_epll(unsigned int pllval, unsigned int baseclk)
 	return (unsigned int)fvco;
 }
 
+static inline void s3c_hsudc_init_phy(void)
+{
+	u32 cfg;
+
+	cfg = readl(S3C2443_PWRCFG) | S3C2443_PWRCFG_USBPHY;
+	writel(cfg, S3C2443_PWRCFG);
+
+	cfg = readl(S3C2443_URSTCON);
+	cfg |= (S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
+	writel(cfg, S3C2443_URSTCON);
+	mdelay(1);
+
+	cfg = readl(S3C2443_URSTCON);
+	cfg &= ~(S3C2443_URSTCON_FUNCRST | S3C2443_URSTCON_PHYRST);
+	writel(cfg, S3C2443_URSTCON);
+
+	cfg = readl(S3C2443_PHYCTRL);
+	cfg &= ~(S3C2443_PHYCTRL_CLKSEL | S3C2443_PHYCTRL_DSPORT);
+	cfg |= (S3C2443_PHYCTRL_EXTCLK | S3C2443_PHYCTRL_PLLSEL);
+	writel(cfg, S3C2443_PHYCTRL);
+
+	cfg = readl(S3C2443_PHYPWR);
+	cfg &= ~(S3C2443_PHYPWR_FSUSPEND | S3C2443_PHYPWR_PLL_PWRDN |
+		S3C2443_PHYPWR_XO_ON | S3C2443_PHYPWR_PLL_REFCLK |
+		S3C2443_PHYPWR_ANALOG_PD);
+	cfg |= S3C2443_PHYPWR_COMMON_ON;
+	writel(cfg, S3C2443_PHYPWR);
+
+	cfg = readl(S3C2443_UCLKCON);
+	cfg |= (S3C2443_UCLKCON_DETECT_VBUS | S3C2443_UCLKCON_FUNC_CLKEN |
+		S3C2443_UCLKCON_TCLKEN);
+	writel(cfg, S3C2443_UCLKCON);
+}
+
+static inline void s3c_hsudc_uninit_phy(void)
+{
+	u32 cfg;
+
+	cfg = readl(S3C2443_PWRCFG) & ~S3C2443_PWRCFG_USBPHY;
+	writel(cfg, S3C2443_PWRCFG);
+
+	writel(S3C2443_PHYPWR_FSUSPEND, S3C2443_PHYPWR);
+
+	cfg = readl(S3C2443_UCLKCON) & ~S3C2443_UCLKCON_FUNC_CLKEN;
+	writel(cfg, S3C2443_UCLKCON);
+}
+
 #endif /*  __ASM_ARM_REGS_S3C2443_CLOCK */
 
diff --git a/arch/arm/mach-s3c64xx/regs-srom.h b/arch/arm/mach-s3c/regs-srom-s3c64xx.h
index 2b37988bdf94..2b37988bdf94 100644
--- a/arch/arm/mach-s3c64xx/regs-srom.h
+++ b/arch/arm/mach-s3c/regs-srom-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-sys.h b/arch/arm/mach-s3c/regs-sys-s3c64xx.h
index 3687325e2bb4..3687325e2bb4 100644
--- a/arch/arm/mach-s3c64xx/regs-sys.h
+++ b/arch/arm/mach-s3c/regs-sys-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-syscon-power.h b/arch/arm/mach-s3c/regs-syscon-power-s3c64xx.h
index a35811cc656e..a35811cc656e 100644
--- a/arch/arm/mach-s3c64xx/regs-syscon-power.h
+++ b/arch/arm/mach-s3c/regs-syscon-power-s3c64xx.h
diff --git a/arch/arm/mach-s3c64xx/regs-usb-hsotg-phy.h b/arch/arm/mach-s3c/regs-usb-hsotg-phy-s3c64xx.h
index deb1dd2d9c83..deb1dd2d9c83 100644
--- a/arch/arm/mach-s3c64xx/regs-usb-hsotg-phy.h
+++ b/arch/arm/mach-s3c/regs-usb-hsotg-phy-s3c64xx.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h b/arch/arm/mach-s3c/rtc-core-s3c24xx.h
index 88510333b96b..e7258b2423fc 100644
--- a/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
+++ b/arch/arm/mach-s3c/rtc-core-s3c24xx.h
@@ -5,8 +5,8 @@
  * Samsung RTC Controller core functions
  */
 
-#ifndef __RTC_CORE_H
-#define __RTC_CORE_H __FILE__
+#ifndef __RTC_CORE_S3C24XX_H
+#define __RTC_CORE_S3C24XX_H __FILE__
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
@@ -20,4 +20,4 @@ static inline void s3c_rtc_setname(char *name)
 	s3c_device_rtc.name = name;
 }
 
-#endif /* __RTC_CORE_H */
+#endif /* __RTC_CORE_S3C24XX_H */
diff --git a/arch/arm/mach-s3c24xx/s3c2410.c b/arch/arm/mach-s3c/s3c2410.c
index 21fd5404bc98..4d39d9939c2f 100644
--- a/arch/arm/mach-s3c24xx/s3c2410.c
+++ b/arch/arm/mach-s3c/s3c2410.c
@@ -25,28 +25,27 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
 #include <asm/irq.h>
 #include <asm/system_misc.h>
 
-#include <plat/cpu-freq.h>
 
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
 
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 /* Initial IO mappings */
 
-static struct map_desc s3c2410_iodesc[] __initdata = {
+static struct map_desc s3c2410_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/s3c2412-power.h b/arch/arm/mach-s3c/s3c2412-power.h
index 0031cfaa1d76..0031cfaa1d76 100644
--- a/arch/arm/mach-s3c24xx/s3c2412-power.h
+++ b/arch/arm/mach-s3c/s3c2412-power.h
diff --git a/arch/arm/mach-s3c24xx/s3c2412.c b/arch/arm/mach-s3c/s3c2412.c
index 8fe4d4670dcb..0b1ca78c9d2a 100644
--- a/arch/arm/mach-s3c24xx/s3c2412.c
+++ b/arch/arm/mach-s3c/s3c2412.c
@@ -29,19 +29,17 @@
 #include <asm/irq.h>
 #include <asm/system_misc.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-
-#include <plat/cpu.h>
-#include <plat/cpu-freq.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/regs-spi.h>
-
-#include "common.h"
-#include "nand-core.h"
-#include "regs-dsc.h"
+#include "map.h"
+#include "regs-clock.h"
+#include "regs-gpio.h"
+
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+
+#include "s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "regs-dsc-s3c24xx.h"
 #include "s3c2412-power.h"
 
 #ifndef CONFIG_CPU_S3C2412_ONLY
@@ -57,7 +55,7 @@ static inline void s3c2412_init_gpio2(void)
 
 /* Initial IO mappings */
 
-static struct map_desc s3c2412_iodesc[] __initdata = {
+static struct map_desc s3c2412_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h b/arch/arm/mach-s3c/s3c2412.h
index 4ff83f956cfb..ed09a0e13bd8 100644
--- a/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
+++ b/arch/arm/mach-s3c/s3c2412.h
@@ -8,6 +8,8 @@
 #ifndef __ARCH_ARM_MACH_S3C24XX_S3C2412_H
 #define __ARCH_ARM_MACH_S3C24XX_S3C2412_H __FILE__
 
+#include "map-s3c.h"
+
 #define S3C2412_MEMREG(x)		(S3C24XX_VA_MEMCTRL + (x))
 #define S3C2412_EBIREG(x)		(S3C2412_VA_EBI + (x))
 
diff --git a/arch/arm/mach-s3c24xx/s3c2416.c b/arch/arm/mach-s3c/s3c2416.c
index 9514196cad8c..126e6ed29713 100644
--- a/arch/arm/mach-s3c24xx/s3c2416.c
+++ b/arch/arm/mach-s3c/s3c2416.c
@@ -26,32 +26,32 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
 #include <asm/proc-fns.h>
 #include <asm/irq.h>
 #include <asm/system_misc.h>
 
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/rtc-core.h>
+#include "regs-s3c2443-clock.h"
+#include "rtc-core-s3c24xx.h"
 
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/sdhci.h>
-#include <plat/pm.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "devs.h"
+#include "cpu.h"
+#include "sdhci.h"
+#include "pm.h"
 
-#include <plat/iic-core.h>
-#include <plat/adc-core.h>
+#include "iic-core.h"
+#include "adc-core.h"
 
-#include "common.h"
-#include "fb-core.h"
-#include "nand-core.h"
-#include "spi-core.h"
+#include "s3c24xx.h"
+#include "fb-core-s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "spi-core-s3c24xx.h"
 
-static struct map_desc s3c2416_iodesc[] __initdata = {
+static struct map_desc s3c2416_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(WATCHDOG),
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
diff --git a/arch/arm/mach-s3c24xx/s3c2440.c b/arch/arm/mach-s3c/s3c2440.c
index 451d9851b0a7..c6cdee4987e8 100644
--- a/arch/arm/mach-s3c24xx/s3c2440.c
+++ b/arch/arm/mach-s3c/s3c2440.c
@@ -23,19 +23,18 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
 #include <asm/irq.h>
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
 
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "gpio-samsung.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct device s3c2440_dev = {
 	.bus		= &s3c2440_subsys,
diff --git a/arch/arm/mach-s3c24xx/s3c2442.c b/arch/arm/mach-s3c/s3c2442.c
index 432d68325c9d..0c0e30b6688f 100644
--- a/arch/arm/mach-s3c24xx/s3c2442.c
+++ b/arch/arm/mach-s3c/s3c2442.c
@@ -21,21 +21,20 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
 #include <linux/atomic.h>
 #include <asm/irq.h>
 
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
 
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "cpu.h"
+#include "pm.h"
 
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "gpio-samsung.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 static struct device s3c2442_dev = {
 	.bus		= &s3c2442_subsys,
diff --git a/arch/arm/mach-s3c24xx/s3c2443.c b/arch/arm/mach-s3c/s3c2443.c
index 4cbeb74cf3d6..08f910144246 100644
--- a/arch/arm/mach-s3c24xx/s3c2443.c
+++ b/arch/arm/mach-s3c/s3c2443.c
@@ -23,26 +23,28 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "map.h"
+#include "gpio-samsung.h"
+#include <mach/irqs.h>
 #include <asm/irq.h>
 #include <asm/system_misc.h>
 
-#include <mach/regs-s3c2443-clock.h>
-#include <mach/rtc-core.h>
+#include "regs-s3c2443-clock.h"
+#include "rtc-core-s3c24xx.h"
 
-#include <plat/gpio-core.h>
-#include <plat/gpio-cfg.h>
-#include <plat/gpio-cfg-helpers.h>
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/adc-core.h>
+#include "gpio-core.h"
+#include "gpio-cfg.h"
+#include "gpio-cfg-helpers.h"
+#include "devs.h"
+#include "cpu.h"
+#include "adc-core.h"
 
-#include "fb-core.h"
-#include "nand-core.h"
-#include "spi-core.h"
+#include "s3c24xx.h"
+#include "fb-core-s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "spi-core-s3c24xx.h"
 
-static struct map_desc s3c2443_iodesc[] __initdata = {
+static struct map_desc s3c2443_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(WATCHDOG),
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
diff --git a/arch/arm/mach-s3c24xx/s3c244x.c b/arch/arm/mach-s3c/s3c244x.c
index a75f588b9d45..95df3491e650 100644
--- a/arch/arm/mach-s3c24xx/s3c244x.c
+++ b/arch/arm/mach-s3c/s3c244x.c
@@ -25,23 +25,21 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
+#include "map.h"
 #include <asm/irq.h>
 
-#include <plat/cpu-freq.h>
+#include "regs-clock.h"
+#include "regs-gpio.h"
 
-#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
+#include "devs.h"
+#include "cpu.h"
+#include "pm.h"
 
-#include <plat/devs.h>
-#include <plat/cpu.h>
-#include <plat/pm.h>
+#include "s3c24xx.h"
+#include "nand-core-s3c24xx.h"
+#include "regs-dsc-s3c24xx.h"
 
-#include "common.h"
-#include "nand-core.h"
-#include "regs-dsc.h"
-
-static struct map_desc s3c244x_iodesc[] __initdata = {
+static struct map_desc s3c244x_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c/s3c24xx.c
index 3dc029c2d2cb..ccfed48c98aa 100644
--- a/arch/arm/mach-s3c24xx/common.c
+++ b/arch/arm/mach-s3c/s3c24xx.c
@@ -17,11 +17,14 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/io.h>
+#include <linux/platform_data/clk-s3c2410.h>
 #include <linux/platform_data/dma-s3c24xx.h>
 #include <linux/dmaengine.h>
+#include <linux/clk/samsung.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-clock.h>
+#include "hardware-s3c24xx.h"
+#include "map.h"
+#include "regs-clock.h"
 #include <asm/irq.h>
 #include <asm/cacheflush.h>
 #include <asm/system_info.h>
@@ -30,15 +33,14 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/dma.h>
+#include "regs-gpio.h"
+#include "dma-s3c24xx.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/cpu-freq.h>
-#include <plat/pwm-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "pwm-core.h"
 
-#include "common.h"
+#include "s3c24xx.h"
 
 /* table of supported CPUs */
 
@@ -137,7 +139,7 @@ static struct cpu_table cpu_ids[] __initdata = {
 
 /* minimal IO mapping */
 
-static struct map_desc s3c_iodesc[] __initdata = {
+static struct map_desc s3c_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(GPIO),
 	IODESC_ENT(IRQ),
 	IODESC_ENT(MEMCTRL),
@@ -220,13 +222,13 @@ void __init s3c24xx_init_io(struct map_desc *mach_desc, int size)
 	samsung_pwm_set_platdata(&s3c24xx_pwm_variant);
 }
 
-void __init samsung_set_timer_source(unsigned int event, unsigned int source)
+void __init s3c24xx_set_timer_source(unsigned int event, unsigned int source)
 {
 	s3c24xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
 	s3c24xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
 }
 
-void __init samsung_timer_init(void)
+void __init s3c24xx_timer_init(void)
 {
 	unsigned int timer_irqs[SAMSUNG_PWM_NUM] = {
 		IRQ_TIMER0, IRQ_TIMER1, IRQ_TIMER2, IRQ_TIMER3, IRQ_TIMER4,
@@ -662,10 +664,17 @@ static struct resource s3c2410_dclk_resource[] = {
 	[0] = DEFINE_RES_MEM(0x56000084, 0x4),
 };
 
+static struct s3c2410_clk_platform_data s3c_clk_platform_data = {
+	.modify_misccr = s3c2410_modify_misccr,
+};
+
 struct platform_device s3c2410_device_dclk = {
 	.name		= "s3c2410-dclk",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(s3c2410_dclk_resource),
 	.resource	= s3c2410_dclk_resource,
+	.dev		= {
+		.platform_data = &s3c_clk_platform_data,
+	},
 };
 #endif
diff --git a/arch/arm/mach-s3c24xx/common.h b/arch/arm/mach-s3c/s3c24xx.h
index d087b20e8857..5848bef5bb49 100644
--- a/arch/arm/mach-s3c24xx/common.h
+++ b/arch/arm/mach-s3c/s3c24xx.h
@@ -10,6 +10,7 @@
 #define __ARCH_ARM_MACH_S3C24XX_COMMON_H __FILE__
 
 #include <linux/reboot.h>
+#include <mach/irqs.h>
 
 struct s3c2410_uartcfg;
 
@@ -108,19 +109,16 @@ extern struct platform_device s3c2443_device_dma;
 
 extern struct platform_device s3c2410_device_dclk;
 
-#ifdef CONFIG_S3C2410_COMMON_CLK
-void __init s3c2410_common_clk_init(struct device_node *np, unsigned long xti_f,
-				    int current_soc,
-				    void __iomem *reg_base);
-#endif
-#ifdef CONFIG_S3C2412_COMMON_CLK
-void __init s3c2412_common_clk_init(struct device_node *np, unsigned long xti_f,
-				unsigned long ext_f, void __iomem *reg_base);
-#endif
-#ifdef CONFIG_S3C2443_COMMON_CLK
-void __init s3c2443_common_clk_init(struct device_node *np, unsigned long xti_f,
-				    int current_soc,
-				    void __iomem *reg_base);
-#endif
+enum s3c24xx_timer_mode {
+	S3C24XX_PWM0,
+	S3C24XX_PWM1,
+	S3C24XX_PWM2,
+	S3C24XX_PWM3,
+	S3C24XX_PWM4,
+};
+
+extern void __init s3c24xx_set_timer_source(enum s3c24xx_timer_mode event,
+					    enum s3c24xx_timer_mode source);
+extern void __init s3c24xx_timer_init(void);
 
 #endif /* __ARCH_ARM_MACH_S3C24XX_COMMON_H */
diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c/s3c6400.c
index 545eea716db8..802f4fb7462d 100644
--- a/arch/arm/mach-s3c64xx/s3c6400.c
+++ b/arch/arm/mach-s3c/s3c6400.c
@@ -26,19 +26,17 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
-#include <plat/cpu-freq.h>
-#include <mach/regs-clock.h>
+#include "regs-clock.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/sdhci.h>
-#include <plat/iic-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "sdhci.h"
+#include "iic-core.h"
 
-#include "common.h"
-#include "onenand-core.h"
+#include "s3c64xx.h"
+#include "onenand-core-s3c64xx.h"
 
 void __init s3c6400_map_io(void)
 {
diff --git a/arch/arm/mach-s3c64xx/s3c6410.c b/arch/arm/mach-s3c/s3c6410.c
index 47e04e019624..dae17d5fd092 100644
--- a/arch/arm/mach-s3c64xx/s3c6410.c
+++ b/arch/arm/mach-s3c/s3c6410.c
@@ -27,21 +27,20 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
-#include <plat/cpu-freq.h>
-#include <mach/regs-clock.h>
+#include <linux/soc/samsung/s3c-pm.h>
+#include "regs-clock.h"
 
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/sdhci.h>
-#include <plat/adc-core.h>
-#include <plat/iic-core.h>
+#include "cpu.h"
+#include "devs.h"
+#include "sdhci.h"
+#include "adc-core.h"
+#include "iic-core.h"
 
-#include "ata-core.h"
-#include "common.h"
-#include "onenand-core.h"
+#include "ata-core-s3c64xx.h"
+#include "s3c64xx.h"
+#include "onenand-core-s3c64xx.h"
 
 void __init s3c6410_map_io(void)
 {
diff --git a/arch/arm/mach-s3c64xx/common.c b/arch/arm/mach-s3c/s3c64xx.c
index 13e91074308a..4dfb648142f2 100644
--- a/arch/arm/mach-s3c64xx/common.c
+++ b/arch/arm/mach-s3c/s3c64xx.c
@@ -24,6 +24,7 @@
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
 #include <linux/io.h>
+#include <linux/clk/samsung.h>
 #include <linux/dma-mapping.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
@@ -34,22 +35,19 @@
 #include <asm/mach/map.h>
 #include <asm/system_misc.h>
 
-#include <mach/map.h>
+#include "map.h"
 #include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-
-#include <plat/cpu.h>
-#include <plat/devs.h>
-#include <plat/pm.h>
-#include <plat/gpio-cfg.h>
-#include <plat/pwm-core.h>
-#include <plat/regs-irqtype.h>
-
-#include "common.h"
-#include "irq-uart.h"
-#include "watchdog-reset.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+
+#include "cpu.h"
+#include "devs.h"
+#include "pm.h"
+#include "gpio-cfg.h"
+#include "pwm-core.h"
+#include "regs-irqtype.h"
+#include "s3c64xx.h"
+#include "irq-uart-s3c64xx.h"
 
 /* External clock frequency */
 static unsigned long xtal_f __ro_after_init = 12000000;
@@ -97,7 +95,12 @@ static struct cpu_table cpu_ids[] __initdata = {
 
 /* minimal IO mapping */
 
-/* see notes on uart map in arch/arm/mach-s3c64xx/include/mach/debug-macro.S */
+/*
+ * note, for the boot process to work we have to keep the UART
+ * virtual address aligned to an 1MiB boundary for the L1
+ * mapping the head code makes. We keep the UART virtual address
+ * aligned and add in the offset when we load the value here.
+ */
 #define UART_OFFS (S3C_PA_UART & 0xfffff)
 
 static struct map_desc s3c_iodesc[] __initdata = {
@@ -170,13 +173,13 @@ static struct samsung_pwm_variant s3c64xx_pwm_variant = {
 	.tclk_mask	= (1 << 7) | (1 << 6) | (1 << 5),
 };
 
-void __init samsung_set_timer_source(unsigned int event, unsigned int source)
+void __init s3c64xx_set_timer_source(unsigned int event, unsigned int source)
 {
 	s3c64xx_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
 	s3c64xx_pwm_variant.output_mask &= ~(BIT(event) | BIT(source));
 }
 
-void __init samsung_timer_init(void)
+void __init s3c64xx_timer_init(void)
 {
 	unsigned int timer_irqs[SAMSUNG_PWM_NUM] = {
 		IRQ_TIMER0_VIC, IRQ_TIMER1_VIC, IRQ_TIMER2_VIC,
@@ -228,13 +231,7 @@ core_initcall(s3c64xx_dev_init);
 
 void __init s3c64xx_init_irq(u32 vic0_valid, u32 vic1_valid)
 {
-	/*
-	 * FIXME: there is no better place to put this at the moment
-	 * (s3c64xx_clk_init needs ioremap and must happen before init_time
-	 * samsung_wdt_reset_init needs clocks)
-	 */
 	s3c64xx_clk_init(NULL, xtal_f, xusbxti_f, soc_is_s3c6400(), S3C_VA_SYS);
-	samsung_wdt_reset_init(S3C_VA_WATCHDOG);
 
 	printk(KERN_DEBUG "%s: initialising interrupts\n", __func__);
 
@@ -428,12 +425,3 @@ static int __init s3c64xx_init_irq_eint(void)
 	return 0;
 }
 arch_initcall(s3c64xx_init_irq_eint);
-
-void s3c64xx_restart(enum reboot_mode mode, const char *cmd)
-{
-	if (mode != REBOOT_SOFT)
-		samsung_wdt_reset();
-
-	/* if all else fails, or mode was for soft, jump to 0 */
-	soft_restart(0);
-}
diff --git a/arch/arm/mach-s3c64xx/common.h b/arch/arm/mach-s3c/s3c64xx.h
index 03670887a764..92258e4f60f6 100644
--- a/arch/arm/mach-s3c64xx/common.h
+++ b/arch/arm/mach-s3c/s3c64xx.h
@@ -19,11 +19,7 @@
 void s3c64xx_init_irq(u32 vic0, u32 vic1);
 void s3c64xx_init_io(struct map_desc *mach_desc, int size);
 
-void s3c64xx_restart(enum reboot_mode mode, const char *cmd);
-
 struct device_node;
-void s3c64xx_clk_init(struct device_node *np, unsigned long xtal_f,
-	unsigned long xusbxti_f, bool is_s3c6400, void __iomem *reg_base);
 void s3c64xx_set_xtal_freq(unsigned long freq);
 void s3c64xx_set_xusbxti_freq(unsigned long freq);
 
@@ -54,4 +50,17 @@ extern struct pl08x_platform_data s3c64xx_dma0_plat_data;
 extern struct pl08x_platform_data s3c64xx_dma1_plat_data;
 #endif
 
+/* Samsung HR-Timer Clock mode */
+enum s3c64xx_timer_mode {
+	S3C64XX_PWM0,
+	S3C64XX_PWM1,
+	S3C64XX_PWM2,
+	S3C64XX_PWM3,
+	S3C64XX_PWM4,
+};
+
+extern void __init s3c64xx_set_timer_source(enum s3c64xx_timer_mode event,
+					    enum s3c64xx_timer_mode source);
+extern void __init s3c64xx_timer_init(void);
+
 #endif /* __ARCH_ARM_MACH_S3C64XX_COMMON_H */
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/mach-s3c/sdhci.h
index 5731e42ea208..9f9d419e58d7 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/mach-s3c/sdhci.h
@@ -15,7 +15,7 @@
 #define __PLAT_S3C_SDHCI_H __FILE__
 
 #include <linux/platform_data/mmc-sdhci-s3c.h>
-#include <plat/devs.h>
+#include "devs.h"
 
 /* s3c_sdhci_set_platdata() - common helper for setting SDHCI platform data
  * @pd: The default platform data for this device.
diff --git a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c b/arch/arm/mach-s3c/setup-fb-24bpp-s3c64xx.c
index 2c7178b26ebb..cfa34b55ca21 100644
--- a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c
+++ b/arch/arm/mach-s3c/setup-fb-24bpp-s3c64xx.c
@@ -12,9 +12,9 @@
 #include <linux/fb.h>
 #include <linux/gpio.h>
 
-#include <plat/fb.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "fb.h"
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 void s3c64xx_fb_gpio_setup_24bpp(void)
 {
diff --git a/arch/arm/mach-s3c24xx/setup-i2c.c b/arch/arm/mach-s3c/setup-i2c-s3c24xx.c
index 1a01d44b5910..0d88366b234c 100644
--- a/arch/arm/mach-s3c24xx/setup-i2c.c
+++ b/arch/arm/mach-s3c/setup-i2c-s3c24xx.c
@@ -10,11 +10,11 @@
 
 struct platform_device;
 
-#include <plat/gpio-cfg.h>
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
+
+#include "gpio-cfg.h"
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
 
 void s3c_i2c0_cfg_gpio(struct platform_device *dev)
 {
diff --git a/arch/arm/mach-s3c64xx/setup-i2c0.c b/arch/arm/mach-s3c/setup-i2c0-s3c64xx.c
index 552eb50da38c..a6ef8d2bc995 100644
--- a/arch/arm/mach-s3c64xx/setup-i2c0.c
+++ b/arch/arm/mach-s3c/setup-i2c0-s3c64xx.c
@@ -14,8 +14,8 @@
 struct platform_device; /* don't need the contents */
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 void s3c_i2c0_cfg_gpio(struct platform_device *dev)
 {
diff --git a/arch/arm/mach-s3c64xx/setup-i2c1.c b/arch/arm/mach-s3c/setup-i2c1-s3c64xx.c
index d231f0fc508d..0fe37363d26e 100644
--- a/arch/arm/mach-s3c64xx/setup-i2c1.c
+++ b/arch/arm/mach-s3c/setup-i2c1-s3c64xx.c
@@ -14,8 +14,8 @@
 struct platform_device; /* don't need the contents */
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 void s3c_i2c1_cfg_gpio(struct platform_device *dev)
 {
diff --git a/arch/arm/mach-s3c64xx/setup-ide.c b/arch/arm/mach-s3c/setup-ide-s3c64xx.c
index 810139a807ce..f11f2b02e49f 100644
--- a/arch/arm/mach-s3c64xx/setup-ide.c
+++ b/arch/arm/mach-s3c/setup-ide-s3c64xx.c
@@ -9,12 +9,13 @@
 #include <linux/gpio.h>
 #include <linux/io.h>
 
-#include <mach/map.h>
-#include <mach/regs-clock.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
 #include <linux/platform_data/ata-samsung_cf.h>
 
+#include "map.h"
+#include "regs-clock.h"
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
+
 void s3c64xx_ide_setup_gpio(void)
 {
 	u32 reg;
diff --git a/arch/arm/mach-s3c64xx/setup-keypad.c b/arch/arm/mach-s3c/setup-keypad-s3c64xx.c
index 351961025273..8463ad37c6ab 100644
--- a/arch/arm/mach-s3c64xx/setup-keypad.c
+++ b/arch/arm/mach-s3c/setup-keypad-s3c64xx.c
@@ -6,9 +6,9 @@
 // GPIO configuration for S3C64XX KeyPad device
 
 #include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <plat/keypad.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "keypad.h"
+#include "gpio-samsung.h"
 
 void samsung_keypad_cfg_gpio(unsigned int rows, unsigned int cols)
 {
diff --git a/arch/arm/mach-s3c24xx/setup-sdhci-gpio.c b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c24xx.c
index 218346a36d1e..02131b3a731d 100644
--- a/arch/arm/mach-s3c24xx/setup-sdhci-gpio.c
+++ b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c24xx.c
@@ -14,9 +14,10 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 
-#include <mach/regs-gpio.h>
-#include <mach/gpio-samsung.h>
-#include <plat/gpio-cfg.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
+#include "sdhci.h"
 
 void s3c2416_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
 {
diff --git a/arch/arm/mach-s3c64xx/setup-sdhci-gpio.c b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c64xx.c
index 138455af4937..646ff949acd5 100644
--- a/arch/arm/mach-s3c64xx/setup-sdhci-gpio.c
+++ b/arch/arm/mach-s3c/setup-sdhci-gpio-s3c64xx.c
@@ -13,9 +13,9 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 
-#include <plat/gpio-cfg.h>
-#include <plat/sdhci.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-cfg.h"
+#include "sdhci.h"
+#include "gpio-samsung.h"
 
 void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
 {
diff --git a/arch/arm/mach-s3c24xx/setup-spi.c b/arch/arm/mach-s3c/setup-spi-s3c24xx.c
index 6c2b96a82da5..93fa1bbc9d5c 100644
--- a/arch/arm/mach-s3c24xx/setup-spi.c
+++ b/arch/arm/mach-s3c/setup-spi-s3c24xx.c
@@ -8,10 +8,10 @@
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 
-#include <plat/gpio-cfg.h>
+#include "gpio-cfg.h"
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "hardware-s3c24xx.h"
+#include "regs-gpio.h"
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
 int s3c64xx_spi0_cfg_gpio(void)
diff --git a/arch/arm/mach-s3c64xx/setup-spi.c b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
index 39dfae1f46e7..efcf78d41585 100644
--- a/arch/arm/mach-s3c64xx/setup-spi.c
+++ b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
@@ -4,8 +4,9 @@
 //		http://www.samsung.com/
 
 #include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/spi-s3c64xx.h>
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
 int s3c64xx_spi0_cfg_gpio(void)
diff --git a/arch/arm/mach-s3c24xx/setup-ts.c b/arch/arm/mach-s3c/setup-ts-s3c24xx.c
index 53a14d4f4852..57363eaeb7e8 100644
--- a/arch/arm/mach-s3c24xx/setup-ts.c
+++ b/arch/arm/mach-s3c/setup-ts-s3c24xx.c
@@ -10,12 +10,14 @@
 
 struct platform_device; /* don't need the contents */
 
-#include <plat/gpio-cfg.h>
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+
+#include "gpio-cfg.h"
+#include "gpio-samsung.h"
 
 /**
  * s3c24xx_ts_cfg_gpio - configure gpio for s3c2410 systems
+ * @dev: Device to configure GPIO for (ignored)
  *
  * Configure the GPIO for the S3C2410 system, where we have external FETs
  * connected to the device (later systems such as the S3C2440 integrate
diff --git a/arch/arm/mach-s3c64xx/setup-usb-phy.c b/arch/arm/mach-s3c/setup-usb-phy-s3c64xx.c
index d6b0e3b268af..500d105afd6b 100644
--- a/arch/arm/mach-s3c64xx/setup-usb-phy.c
+++ b/arch/arm/mach-s3c/setup-usb-phy-s3c64xx.c
@@ -8,12 +8,12 @@
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/platform_device.h>
-#include <mach/map.h>
-#include <plat/cpu.h>
-#include <plat/usb-phy.h>
+#include "map.h"
+#include "cpu.h"
+#include "usb-phy.h"
 
-#include "regs-sys.h"
-#include "regs-usb-hsotg-phy.h"
+#include "regs-sys-s3c64xx.h"
+#include "regs-usb-hsotg-phy-s3c64xx.h"
 
 enum samsung_usb_phy_type {
 	USB_PHY_TYPE_DEVICE,
@@ -31,7 +31,7 @@ static int s3c_usb_otgphy_init(struct platform_device *pdev)
 	phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
 
 	xusbxti = clk_get(&pdev->dev, "xusbxti");
-	if (xusbxti && !IS_ERR(xusbxti)) {
+	if (!IS_ERR(xusbxti)) {
 		switch (clk_get_rate(xusbxti)) {
 		case 12 * MHZ:
 			phyclk |= S3C_PHYCLK_CLKSEL_12M;
diff --git a/arch/arm/mach-s3c24xx/simtec-audio.c b/arch/arm/mach-s3c/simtec-audio.c
index 12e17f82dae3..487485bcc2ab 100644
--- a/arch/arm/mach-s3c24xx/simtec-audio.c
+++ b/arch/arm/mach-s3c/simtec-audio.c
@@ -12,11 +12,12 @@
 #include <linux/device.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
+#include "gpio-samsung.h"
+#include "gpio-cfg.h"
 
 #include <linux/platform_data/asoc-s3c24xx_simtec.h>
-#include <plat/devs.h>
+#include "devs.h"
 
 #include "bast.h"
 #include "simtec.h"
@@ -65,6 +66,10 @@ int __init simtec_audio_add(const char *name, bool has_lr_routing,
 	if (has_lr_routing)
 		simtec_audio_platdata.startup = simtec_audio_startup_lrroute;
 
+	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
+	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
+			      S3C_GPIO_PULL_NONE);
+
 	platform_device_register(&s3c_device_iis);
 	platform_device_register(&simtec_audio_dev);
 	return 0;
diff --git a/arch/arm/mach-s3c24xx/simtec-nor.c b/arch/arm/mach-s3c/simtec-nor.c
index 26b18497e959..a6fba056a747 100644
--- a/arch/arm/mach-s3c24xx/simtec-nor.c
+++ b/arch/arm/mach-s3c/simtec-nor.c
@@ -21,7 +21,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/map.h>
+#include "map.h"
 
 #include "bast.h"
 #include "simtec.h"
diff --git a/arch/arm/mach-s3c24xx/simtec-pm.c b/arch/arm/mach-s3c/simtec-pm.c
index c19074d81389..490256a766e2 100644
--- a/arch/arm/mach-s3c24xx/simtec-pm.c
+++ b/arch/arm/mach-s3c/simtec-pm.c
@@ -19,16 +19,14 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/hardware.h>
-
-#include <mach/map.h>
-#include <mach/regs-gpio.h>
+#include "map.h"
+#include "regs-gpio.h"
 
 #include <asm/mach-types.h>
 
-#include <plat/pm.h>
+#include "pm.h"
 
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 #define COPYRIGHT ", Copyright 2005 Simtec Electronics"
 
diff --git a/arch/arm/mach-s3c24xx/simtec-usb.c b/arch/arm/mach-s3c/simtec-usb.c
index dc1016ffed94..18fe0642743a 100644
--- a/arch/arm/mach-s3c24xx/simtec-usb.c
+++ b/arch/arm/mach-s3c/simtec-usb.c
@@ -23,12 +23,12 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-#include <mach/gpio-samsung.h>
+#include "gpio-samsung.h"
+#include <mach/irqs.h>
 #include <asm/irq.h>
 
 #include <linux/platform_data/usb-ohci-s3c2410.h>
-#include <plat/devs.h>
+#include "devs.h"
 
 #include "bast.h"
 #include "simtec.h"
diff --git a/arch/arm/mach-s3c24xx/simtec.h b/arch/arm/mach-s3c/simtec.h
index d96bd60872b8..d96bd60872b8 100644
--- a/arch/arm/mach-s3c24xx/simtec.h
+++ b/arch/arm/mach-s3c/simtec.h
diff --git a/arch/arm/mach-s3c24xx/sleep-s3c2410.S b/arch/arm/mach-s3c/sleep-s3c2410.S
index 659f9eff9de2..04aded98782b 100644
--- a/arch/arm/mach-s3c24xx/sleep-s3c2410.S
+++ b/arch/arm/mach-s3c/sleep-s3c2410.S
@@ -13,13 +13,12 @@
 #include <linux/linkage.h>
 #include <linux/serial_s3c.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
 
-#include "regs-mem.h"
+#include "regs-mem-s3c24xx.h"
 
 	/* s3c2410_cpu_suspend
 	 *
diff --git a/arch/arm/mach-s3c24xx/sleep-s3c2412.S b/arch/arm/mach-s3c/sleep-s3c2412.S
index c373f1ca862b..b4b61737fbb2 100644
--- a/arch/arm/mach-s3c24xx/sleep-s3c2412.S
+++ b/arch/arm/mach-s3c/sleep-s3c2412.S
@@ -8,10 +8,9 @@
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <mach/regs-irq.h>
+#include "regs-irq.h"
 
 	.text
 
diff --git a/arch/arm/mach-s3c24xx/sleep.S b/arch/arm/mach-s3c/sleep-s3c24xx.S
index f0f11ad60c52..4b2af91f3dce 100644
--- a/arch/arm/mach-s3c24xx/sleep.S
+++ b/arch/arm/mach-s3c/sleep-s3c24xx.S
@@ -13,11 +13,10 @@
 #include <linux/linkage.h>
 #include <linux/serial_s3c.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/map.h>
+#include "map.h"
 
-#include <mach/regs-gpio.h>
-#include <mach/regs-clock.h>
+#include "regs-gpio.h"
+#include "regs-clock.h"
 
 /*
  * S3C24XX_DEBUG_RESUME is dangerous if your bootloader does not
diff --git a/arch/arm/mach-s3c64xx/sleep.S b/arch/arm/mach-s3c/sleep-s3c64xx.S
index 39e16a07a5e4..739e53fbce09 100644
--- a/arch/arm/mach-s3c64xx/sleep.S
+++ b/arch/arm/mach-s3c/sleep-s3c64xx.S
@@ -11,12 +11,12 @@
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
-#include <mach/map.h>
+#include "map.h"
 
 #undef S3C64XX_VA_GPIO
 #define S3C64XX_VA_GPIO (0x0)
 
-#include <mach/regs-gpio.h>
+#include "regs-gpio.h"
 
 #define LL_UART (S3C_PA_UART + (0x400 * CONFIG_S3C_LOWLEVEL_UART_PORT))
 
diff --git a/arch/arm/mach-s3c24xx/spi-core.h b/arch/arm/mach-s3c/spi-core-s3c24xx.h
index 1048fac629a2..057667469cc3 100644
--- a/arch/arm/mach-s3c24xx/spi-core.h
+++ b/arch/arm/mach-s3c/spi-core-s3c24xx.h
@@ -3,8 +3,8 @@
  * Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
  */
 
-#ifndef __PLAT_S3C_SPI_CORE_H
-#define __PLAT_S3C_SPI_CORE_H
+#ifndef __PLAT_S3C_SPI_CORE_S3C24XX_H
+#define __PLAT_S3C_SPI_CORE_S3C24XX_H
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
@@ -24,4 +24,4 @@ static inline void s3c24xx_spi_setname(char *name)
 #endif
 }
 
-#endif /* __PLAT_S3C_SPI_CORE_H */
+#endif /* __PLAT_S3C_SPI_CORE_S3C24XX_H */
diff --git a/arch/arm/plat-samsung/include/plat/usb-phy.h b/arch/arm/mach-s3c/usb-phy.h
index 759d66a0773a..759d66a0773a 100644
--- a/arch/arm/plat-samsung/include/plat/usb-phy.h
+++ b/arch/arm/mach-s3c/usb-phy.h
diff --git a/arch/arm/mach-s3c24xx/vr1000.h b/arch/arm/mach-s3c/vr1000.h
index 3cfa296bec2a..3cfa296bec2a 100644
--- a/arch/arm/mach-s3c24xx/vr1000.h
+++ b/arch/arm/mach-s3c/vr1000.h
diff --git a/arch/arm/plat-samsung/wakeup-mask.c b/arch/arm/mach-s3c/wakeup-mask.c
index 24f96fb80738..b490e7527c66 100644
--- a/arch/arm/plat-samsung/wakeup-mask.c
+++ b/arch/arm/mach-s3c/wakeup-mask.c
@@ -11,8 +11,8 @@
 #include <linux/irq.h>
 #include <linux/io.h>
 
-#include <plat/wakeup-mask.h>
-#include <plat/pm.h>
+#include "wakeup-mask.h"
+#include "pm.h"
 
 void samsung_sync_wakemask(void __iomem *reg,
 			   const struct samsung_wakeup_mask *mask, int nr_mask)
diff --git a/arch/arm/plat-samsung/include/plat/wakeup-mask.h b/arch/arm/mach-s3c/wakeup-mask.h
index 630909e6630b..630909e6630b 100644
--- a/arch/arm/plat-samsung/include/plat/wakeup-mask.h
+++ b/arch/arm/mach-s3c/wakeup-mask.h
diff --git a/arch/arm/mach-s3c24xx/include/mach/fb.h b/arch/arm/mach-s3c24xx/include/mach/fb.h
deleted file mode 100644
index 4e539cb8b884..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/fb.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <plat/fb-s3c2410.h>
diff --git a/arch/arm/mach-s3c24xx/include/mach/io.h b/arch/arm/mach-s3c24xx/include/mach/io.h
deleted file mode 100644
index f960e6d10114..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/io.h
+++ /dev/null
@@ -1,212 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-s3c2410/include/mach/io.h
- *  from arch/arm/mach-rpc/include/mach/io.h
- *
- * Copyright (C) 1997 Russell King
- *	     (C) 2003 Simtec Electronics
-*/
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <mach/hardware.h>
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses.  PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1.  ARM addresses are above A28
- * and are translated to the start of IO.  Note that all addresses are
- * not shifted left!
- */
-
-#define __PORT_PCIO(x)	((x) < (1<<28))
-
-#define PCIO_BASE	 (S3C24XX_VA_ISA_WORD)
-#define PCIO_BASE_b	 (S3C24XX_VA_ISA_BYTE)
-#define PCIO_BASE_w	 (S3C24XX_VA_ISA_WORD)
-#define PCIO_BASE_l	 (S3C24XX_VA_ISA_WORD)
-/*
- * Dynamic IO functions - let the compiler
- * optimize the expressions
- */
-
-#define DECLARE_DYN_OUT(sz,fnsuffix,instr) \
-static inline void __out##fnsuffix (unsigned int val, unsigned int port) \
-{ \
-	unsigned long temp;				      \
-	__asm__ __volatile__(				      \
-	"cmp	%2, #(1<<28)\n\t"			      \
-	"mov	%0, %2\n\t"				      \
-	"addcc	%0, %0, %3\n\t"				      \
-	"str" instr " %1, [%0, #0 ]	@ out" #fnsuffix      \
-	: "=&r" (temp)					      \
-	: "r" (val), "r" (port), "Ir" (PCIO_BASE_##fnsuffix)  \
-	: "cc");					      \
-}
-
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr)				\
-static inline unsigned sz __in##fnsuffix (unsigned int port)		\
-{									\
-	unsigned long temp, value;					\
-	__asm__ __volatile__(						\
-	"cmp	%2, #(1<<28)\n\t"					\
-	"mov	%0, %2\n\t"						\
-	"addcc	%0, %0, %3\n\t"						\
-	"ldr" instr "	%1, [%0, #0 ]	@ in" #fnsuffix		\
-	: "=&r" (temp), "=r" (value)					\
-	: "r" (port), "Ir" (PCIO_BASE_##fnsuffix)	\
-	: "cc");							\
-	return (unsigned sz)value;					\
-}
-
-static inline void __iomem *__ioaddr (unsigned long port)
-{
-	return __PORT_PCIO(port) ? (PCIO_BASE + port) : (void __iomem *)port;
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr)	\
-	DECLARE_DYN_IN(sz,fnsuffix,instr) \
-	DECLARE_DYN_OUT(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"h")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
- *
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
- */
-#define __outbc(value,port)						\
-({									\
-	if (__PORT_PCIO((port)))					\
-		__asm__ __volatile__(					\
-		"strb	%0, [%1, %2]	@ outbc"			\
-		: : "r" (value), "r" (PCIO_BASE), "Jr" ((port)));	\
-	else								\
-		__asm__ __volatile__(					\
-		"strb	%0, [%1, #0]	@ outbc"			\
-		: : "r" (value), "r" ((port)));				\
-})
-
-#define __inbc(port)							\
-({									\
-	unsigned char result;						\
-	if (__PORT_PCIO((port)))					\
-		__asm__ __volatile__(					\
-		"ldrb	%0, [%1, %2]	@ inbc"				\
-		: "=r" (result) : "r" (PCIO_BASE), "Jr" ((port)));	\
-	else								\
-		__asm__ __volatile__(					\
-		"ldrb	%0, [%1, #0]	@ inbc"				\
-		: "=r" (result) : "r" ((port)));			\
-	result;								\
-})
-
-#define __outwc(value,port)						\
-({									\
-	unsigned long v = value;					\
-	if (__PORT_PCIO((port))) {					\
-		if ((port) < 256 && (port) > -256)			\
-			__asm__ __volatile__(				\
-			"strh	%0, [%1, %2]	@ outwc"		\
-			: : "r" (v), "r" (PCIO_BASE), "Jr" ((port)));	\
-		else if ((port) > 0)					\
-			__asm__ __volatile__(				\
-			"strh	%0, [%1, %2]	@ outwc"		\
-			: : "r" (v),					\
-			    "r" (PCIO_BASE + ((port) & ~0xff)),		\
-			     "Jr" (((port) & 0xff)));			\
-		else							\
-			__asm__ __volatile__(				\
-			"strh	%0, [%1, #0]	@ outwc"		\
-			: : "r" (v),					\
-			    "r" (PCIO_BASE + (port)));			\
-	} else								\
-		__asm__ __volatile__(					\
-		"strh	%0, [%1, #0]	@ outwc"			\
-		: : "r" (v), "r" ((port)));				\
-})
-
-#define __inwc(port)							\
-({									\
-	unsigned short result;						\
-	if (__PORT_PCIO((port))) {					\
-		if ((port) < 256 && (port) > -256 )			\
-			__asm__ __volatile__(				\
-			"ldrh	%0, [%1, %2]	@ inwc"			\
-			: "=r" (result)					\
-			: "r" (PCIO_BASE),				\
-			  "Jr" ((port)));				\
-		else if ((port) > 0)					\
-			__asm__ __volatile__(				\
-			"ldrh	%0, [%1, %2]	@ inwc"			\
-			: "=r" (result)					\
-			: "r" (PCIO_BASE + ((port) & ~0xff)),		\
-			  "Jr" (((port) & 0xff)));			\
-		else							\
-			__asm__ __volatile__(				\
-			"ldrh	%0, [%1, #0]	@ inwc"			\
-			: "=r" (result)					\
-			: "r" (PCIO_BASE + ((port))));			\
-	} else								\
-		__asm__ __volatile__(					\
-		"ldrh	%0, [%1, #0]	@ inwc"				\
-		: "=r" (result) : "r" ((port)));			\
-	result;								\
-})
-
-#define __outlc(value,port)						\
-({									\
-	unsigned long v = value;					\
-	if (__PORT_PCIO((port)))					\
-		__asm__ __volatile__(					\
-		"str	%0, [%1, %2]	@ outlc"			\
-		: : "r" (v), "r" (PCIO_BASE), "Jr" ((port)));	\
-	else								\
-		__asm__ __volatile__(					\
-		"str	%0, [%1, #0]	@ outlc"			\
-		: : "r" (v), "r" ((port)));		\
-})
-
-#define __inlc(port)							\
-({									\
-	unsigned long result;						\
-	if (__PORT_PCIO((port)))					\
-		__asm__ __volatile__(					\
-		"ldr	%0, [%1, %2]	@ inlc"				\
-		: "=r" (result) : "r" (PCIO_BASE), "Jr" ((port)));	\
-	else								\
-		__asm__ __volatile__(					\
-		"ldr	%0, [%1, #0]	@ inlc"				\
-		: "=r" (result) : "r" ((port)));		\
-	result;								\
-})
-
-#define __ioaddrc(port)	((__PORT_PCIO(port) ? PCIO_BASE + (port) : (void __iomem *)0 + (port)))
-
-#define inb(p)		(__builtin_constant_p((p)) ? __inbc(p)	   : __inb(p))
-#define inw(p)		(__builtin_constant_p((p)) ? __inwc(p)	   : __inw(p))
-#define inl(p)		(__builtin_constant_p((p)) ? __inlc(p)	   : __inl(p))
-#define outb(v,p)	(__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p)	(__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p)	(__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-#define __ioaddr(p)	(__builtin_constant_p((p)) ? __ioaddr(p)  : __ioaddrc(p))
-
-#define insb(p,d,l)	__raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l)	__raw_readsw(__ioaddr(p),d,l)
-#define insl(p,d,l)	__raw_readsl(__ioaddr(p),d,l)
-
-#define outsb(p,d,l)	__raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l)	__raw_writesw(__ioaddr(p),d,l)
-#define outsl(p,d,l)	__raw_writesl(__ioaddr(p),d,l)
-
-#endif
diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-lcd.h b/arch/arm/mach-s3c24xx/include/mach/regs-lcd.h
deleted file mode 100644
index 4c3434f261bb..000000000000
--- a/arch/arm/mach-s3c24xx/include/mach/regs-lcd.h
+++ /dev/null
@@ -1,157 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
- *		      http://www.simtec.co.uk/products/SWLINUX/
- */
-
-#ifndef ___ASM_ARCH_REGS_LCD_H
-#define ___ASM_ARCH_REGS_LCD_H
-
-#define S3C2410_LCDREG(x)	(x)
-
-/* LCD control registers */
-#define S3C2410_LCDCON1	    S3C2410_LCDREG(0x00)
-#define S3C2410_LCDCON2	    S3C2410_LCDREG(0x04)
-#define S3C2410_LCDCON3	    S3C2410_LCDREG(0x08)
-#define S3C2410_LCDCON4	    S3C2410_LCDREG(0x0C)
-#define S3C2410_LCDCON5	    S3C2410_LCDREG(0x10)
-
-#define S3C2410_LCDCON1_CLKVAL(x)  ((x) << 8)
-#define S3C2410_LCDCON1_MMODE	   (1<<7)
-#define S3C2410_LCDCON1_DSCAN4	   (0<<5)
-#define S3C2410_LCDCON1_STN4	   (1<<5)
-#define S3C2410_LCDCON1_STN8	   (2<<5)
-#define S3C2410_LCDCON1_TFT	   (3<<5)
-
-#define S3C2410_LCDCON1_STN1BPP	   (0<<1)
-#define S3C2410_LCDCON1_STN2GREY   (1<<1)
-#define S3C2410_LCDCON1_STN4GREY   (2<<1)
-#define S3C2410_LCDCON1_STN8BPP	   (3<<1)
-#define S3C2410_LCDCON1_STN12BPP   (4<<1)
-
-#define S3C2410_LCDCON1_TFT1BPP	   (8<<1)
-#define S3C2410_LCDCON1_TFT2BPP	   (9<<1)
-#define S3C2410_LCDCON1_TFT4BPP	   (10<<1)
-#define S3C2410_LCDCON1_TFT8BPP	   (11<<1)
-#define S3C2410_LCDCON1_TFT16BPP   (12<<1)
-#define S3C2410_LCDCON1_TFT24BPP   (13<<1)
-
-#define S3C2410_LCDCON1_ENVID	   (1)
-
-#define S3C2410_LCDCON1_MODEMASK    0x1E
-
-#define S3C2410_LCDCON2_VBPD(x)	    ((x) << 24)
-#define S3C2410_LCDCON2_LINEVAL(x)  ((x) << 14)
-#define S3C2410_LCDCON2_VFPD(x)	    ((x) << 6)
-#define S3C2410_LCDCON2_VSPW(x)	    ((x) << 0)
-
-#define S3C2410_LCDCON2_GET_VBPD(x) ( ((x) >> 24) & 0xFF)
-#define S3C2410_LCDCON2_GET_VFPD(x) ( ((x) >>  6) & 0xFF)
-#define S3C2410_LCDCON2_GET_VSPW(x) ( ((x) >>  0) & 0x3F)
-
-#define S3C2410_LCDCON3_HBPD(x)	    ((x) << 19)
-#define S3C2410_LCDCON3_WDLY(x)	    ((x) << 19)
-#define S3C2410_LCDCON3_HOZVAL(x)   ((x) << 8)
-#define S3C2410_LCDCON3_HFPD(x)	    ((x) << 0)
-#define S3C2410_LCDCON3_LINEBLANK(x)((x) << 0)
-
-#define S3C2410_LCDCON3_GET_HBPD(x) ( ((x) >> 19) & 0x7F)
-#define S3C2410_LCDCON3_GET_HFPD(x) ( ((x) >>  0) & 0xFF)
-
-/* LDCCON4 changes for STN mode on the S3C2412 */
-
-#define S3C2410_LCDCON4_MVAL(x)	    ((x) << 8)
-#define S3C2410_LCDCON4_HSPW(x)	    ((x) << 0)
-#define S3C2410_LCDCON4_WLH(x)	    ((x) << 0)
-
-#define S3C2410_LCDCON4_GET_HSPW(x) ( ((x) >>  0) & 0xFF)
-
-#define S3C2410_LCDCON5_BPP24BL	    (1<<12)
-#define S3C2410_LCDCON5_FRM565	    (1<<11)
-#define S3C2410_LCDCON5_INVVCLK	    (1<<10)
-#define S3C2410_LCDCON5_INVVLINE    (1<<9)
-#define S3C2410_LCDCON5_INVVFRAME   (1<<8)
-#define S3C2410_LCDCON5_INVVD	    (1<<7)
-#define S3C2410_LCDCON5_INVVDEN	    (1<<6)
-#define S3C2410_LCDCON5_INVPWREN    (1<<5)
-#define S3C2410_LCDCON5_INVLEND	    (1<<4)
-#define S3C2410_LCDCON5_PWREN	    (1<<3)
-#define S3C2410_LCDCON5_ENLEND	    (1<<2)
-#define S3C2410_LCDCON5_BSWP	    (1<<1)
-#define S3C2410_LCDCON5_HWSWP	    (1<<0)
-
-/* framebuffer start addressed */
-#define S3C2410_LCDSADDR1   S3C2410_LCDREG(0x14)
-#define S3C2410_LCDSADDR2   S3C2410_LCDREG(0x18)
-#define S3C2410_LCDSADDR3   S3C2410_LCDREG(0x1C)
-
-#define S3C2410_LCDBANK(x)	((x) << 21)
-#define S3C2410_LCDBASEU(x)	(x)
-
-#define S3C2410_OFFSIZE(x)	((x) << 11)
-#define S3C2410_PAGEWIDTH(x)	(x)
-
-/* colour lookup and miscellaneous controls */
-
-#define S3C2410_REDLUT	   S3C2410_LCDREG(0x20)
-#define S3C2410_GREENLUT   S3C2410_LCDREG(0x24)
-#define S3C2410_BLUELUT	   S3C2410_LCDREG(0x28)
-
-#define S3C2410_DITHMODE   S3C2410_LCDREG(0x4C)
-#define S3C2410_TPAL	   S3C2410_LCDREG(0x50)
-
-#define S3C2410_TPAL_EN		(1<<24)
-
-/* interrupt info */
-#define S3C2410_LCDINTPND  S3C2410_LCDREG(0x54)
-#define S3C2410_LCDSRCPND  S3C2410_LCDREG(0x58)
-#define S3C2410_LCDINTMSK  S3C2410_LCDREG(0x5C)
-#define S3C2410_LCDINT_FIWSEL	(1<<2)
-#define	S3C2410_LCDINT_FRSYNC	(1<<1)
-#define S3C2410_LCDINT_FICNT	(1<<0)
-
-/* s3c2442 extra stn registers */
-
-#define S3C2442_REDLUT		S3C2410_LCDREG(0x20)
-#define S3C2442_GREENLUT	S3C2410_LCDREG(0x24)
-#define S3C2442_BLUELUT		S3C2410_LCDREG(0x28)
-#define S3C2442_DITHMODE	S3C2410_LCDREG(0x20)
-
-#define S3C2410_LPCSEL	   S3C2410_LCDREG(0x60)
-
-#define S3C2410_TFTPAL(x)  S3C2410_LCDREG((0x400 + (x)*4))
-
-/* S3C2412 registers */
-
-#define S3C2412_TPAL		S3C2410_LCDREG(0x20)
-
-#define S3C2412_LCDINTPND	S3C2410_LCDREG(0x24)
-#define S3C2412_LCDSRCPND	S3C2410_LCDREG(0x28)
-#define S3C2412_LCDINTMSK	S3C2410_LCDREG(0x2C)
-
-#define S3C2412_TCONSEL		S3C2410_LCDREG(0x30)
-
-#define S3C2412_LCDCON6		S3C2410_LCDREG(0x34)
-#define S3C2412_LCDCON7		S3C2410_LCDREG(0x38)
-#define S3C2412_LCDCON8		S3C2410_LCDREG(0x3C)
-#define S3C2412_LCDCON9		S3C2410_LCDREG(0x40)
-
-#define S3C2412_REDLUT(x)	S3C2410_LCDREG(0x44 + ((x)*4))
-#define S3C2412_GREENLUT(x)	S3C2410_LCDREG(0x60 + ((x)*4))
-#define S3C2412_BLUELUT(x)	S3C2410_LCDREG(0x98 + ((x)*4))
-
-#define S3C2412_FRCPAT(x)	S3C2410_LCDREG(0xB4 + ((x)*4))
-
-/* general registers */
-
-/* base of the LCD registers, where INTPND, INTSRC and then INTMSK
- * are available. */
-
-#define S3C2410_LCDINTBASE	S3C2410_LCDREG(0x54)
-#define S3C2412_LCDINTBASE	S3C2410_LCDREG(0x24)
-
-#define S3C24XX_LCDINTPND	(0x00)
-#define S3C24XX_LCDSRCPND	(0x04)
-#define S3C24XX_LCDINTMSK	(0x08)
-
-#endif /* ___ASM_ARCH_REGS_LCD_H */
diff --git a/arch/arm/mach-s3c24xx/setup-camif.c b/arch/arm/mach-s3c24xx/setup-camif.c
deleted file mode 100644
index 2b262fae3f61..000000000000
--- a/arch/arm/mach-s3c24xx/setup-camif.c
+++ /dev/null
@@ -1,67 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (C) 2012 Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
-//
-// Helper functions for S3C24XX/S3C64XX SoC series CAMIF driver
-
-#include <linux/gpio.h>
-#include <plat/gpio-cfg.h>
-#include <mach/gpio-samsung.h>
-
-/* Number of camera port pins, without FIELD */
-#define S3C_CAMIF_NUM_GPIOS	13
-
-/* Default camera port configuration helpers. */
-
-static void camif_get_gpios(int *gpio_start, int *gpio_reset)
-{
-#ifdef CONFIG_ARCH_S3C24XX
-	*gpio_start = S3C2410_GPJ(0);
-	*gpio_reset = S3C2410_GPJ(12);
-#else
-	/* s3c64xx */
-	*gpio_start = S3C64XX_GPF(0);
-	*gpio_reset = S3C64XX_GPF(3);
-#endif
-}
-
-int s3c_camif_gpio_get(void)
-{
-	int gpio_start, gpio_reset;
-	int ret, i;
-
-	camif_get_gpios(&gpio_start, &gpio_reset);
-
-	for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
-		int gpio = gpio_start + i;
-
-		if (gpio == gpio_reset)
-			continue;
-
-		ret = gpio_request(gpio, "camif");
-		if (!ret)
-			ret = s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
-		if (ret) {
-			pr_err("failed to configure GPIO %d\n", gpio);
-			for (--i; i >= 0; i--)
-				gpio_free(gpio--);
-			return ret;
-		}
-		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
-	}
-
-	return 0;
-}
-
-void s3c_camif_gpio_put(void)
-{
-	int i, gpio_start, gpio_reset;
-
-	camif_get_gpios(&gpio_start, &gpio_reset);
-
-	for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
-		int gpio = gpio_start + i;
-		if (gpio != gpio_reset)
-			gpio_free(gpio);
-	}
-}
diff --git a/arch/arm/mach-s3c64xx/include/mach/hardware.h b/arch/arm/mach-s3c64xx/include/mach/hardware.h
deleted file mode 100644
index c4ed359474de..000000000000
--- a/arch/arm/mach-s3c64xx/include/mach/hardware.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/* linux/arch/arm/mach-s3c6400/include/mach/hardware.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- *      Ben Dooks <ben@simtec.co.uk>
- *      http://armlinux.simtec.co.uk/
- *
- * S3C6400 - Hardware support
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H __FILE__
-
-/* currently nothing here, placeholder */
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s3c64xx/watchdog-reset.h b/arch/arm/mach-s3c64xx/watchdog-reset.h
deleted file mode 100644
index 1042d6c463dc..000000000000
--- a/arch/arm/mach-s3c64xx/watchdog-reset.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2008 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - System define for arch_reset() function
- */
-
-#ifndef __PLAT_SAMSUNG_WATCHDOG_RESET_H
-#define __PLAT_SAMSUNG_WATCHDOG_RESET_H
-
-extern void samsung_wdt_reset(void);
-extern void samsung_wdt_reset_of_init(void);
-extern void samsung_wdt_reset_init(void __iomem *base);
-
-#endif /* __PLAT_SAMSUNG_WATCHDOG_RESET_H */
diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 03984a791879..95d4e8284866 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -14,10 +14,10 @@ config ARCH_S5PV210
 	select COMMON_CLK_SAMSUNG
 	select GPIOLIB
 	select HAVE_S3C2410_I2C if I2C
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select HAVE_S3C_RTC if RTC_CLASS
 	select PINCTRL
 	select PINCTRL_EXYNOS
+	select SOC_SAMSUNG
 	help
 	  Samsung S5PV210/S5PC110 series based systems
 
diff --git a/arch/arm/mach-s5pv210/Makefile b/arch/arm/mach-s5pv210/Makefile
index e7b551e18e5c..aa0a1f091daf 100644
--- a/arch/arm/mach-s5pv210/Makefile
+++ b/arch/arm/mach-s5pv210/Makefile
@@ -3,12 +3,5 @@
 # Copyright (c) 2010 Samsung Electronics Co., Ltd.
 # 		http://www.samsung.com/
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/arch/arm/plat-samsung/include
-
-# Core
-
 obj-$(CONFIG_PM_SLEEP)		+= pm.o sleep.o
-
-# machine support
-
 obj-y				+= s5pv210.o
diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c
index b336df0c57f3..d59c094cdea8 100644
--- a/arch/arm/mach-s5pv210/pm.c
+++ b/arch/arm/mach-s5pv210/pm.c
@@ -13,15 +13,56 @@
 #include <linux/suspend.h>
 #include <linux/syscore_ops.h>
 #include <linux/io.h>
+#include <linux/soc/samsung/s3c-pm.h>
 
 #include <asm/cacheflush.h>
 #include <asm/suspend.h>
 
-#include <plat/pm-common.h>
-
 #include "common.h"
 #include "regs-clock.h"
 
+/* helper functions to save and restore register state */
+struct sleep_save {
+	void __iomem	*reg;
+	unsigned long	val;
+};
+
+#define SAVE_ITEM(x) \
+	{ .reg = (x) }
+
+/**
+ * s3c_pm_do_save() - save a set of registers for restoration on resume.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Run through the list of registers given, saving their contents in the
+ * array for later restoration when we wakeup.
+ */
+static void s3c_pm_do_save(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		ptr->val = readl_relaxed(ptr->reg);
+		S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val);
+	}
+}
+
+/**
+ * s3c_pm_do_restore() - restore register values from the save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Restore the register values saved from s3c_pm_do_save().
+ *
+ * WARNING: Do not put any debug in here that may effect memory or use
+ * peripherals, as things may be changing!
+*/
+
+static void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++)
+		writel_relaxed(ptr->val, ptr->reg);
+}
+
 static struct sleep_save s5pv210_core_save[] = {
 	/* Clock ETC */
 	SAVE_ITEM(S5P_MDNIE_SEL),
@@ -99,8 +140,6 @@ static int s5pv210_suspend_enter(suspend_state_t state)
 	u32 eint_wakeup_mask = s5pv210_read_eint_wakeup_mask();
 	int ret;
 
-	s3c_pm_debug_init();
-
 	S3C_PMDBG("%s: suspending the system...\n", __func__);
 
 	S3C_PMDBG("%s: wakeup masks: %08x,%08x\n", __func__,
@@ -113,7 +152,7 @@ static int s5pv210_suspend_enter(suspend_state_t state)
 		return -EINVAL;
 	}
 
-	s3c_pm_save_uarts();
+	s3c_pm_save_uarts(false);
 	s5pv210_pm_prepare();
 	flush_cache_all();
 	s3c_pm_check_store();
@@ -122,7 +161,7 @@ static int s5pv210_suspend_enter(suspend_state_t state)
 	if (ret)
 		return ret;
 
-	s3c_pm_restore_uarts();
+	s3c_pm_restore_uarts(false);
 
 	S3C_PMDBG("%s: wakeup stat: %08x\n", __func__,
 			__raw_readl(S5P_WAKEUP_STAT));
diff --git a/arch/arm/mach-s5pv210/regs-clock.h b/arch/arm/mach-s5pv210/regs-clock.h
index 2a35c831a9b0..9cad2306e470 100644
--- a/arch/arm/mach-s5pv210/regs-clock.h
+++ b/arch/arm/mach-s5pv210/regs-clock.h
@@ -9,7 +9,9 @@
 #ifndef __ASM_ARCH_REGS_CLOCK_H
 #define __ASM_ARCH_REGS_CLOCK_H __FILE__
 
-#include <plat/map-base.h>
+#define S3C_ADDR_BASE		0xF6000000
+#define S3C_ADDR(x)		((void __iomem __force *)S3C_ADDR_BASE + (x))
+#define S3C_VA_SYS		S3C_ADDR(0x00100000)
 
 #define S5P_CLKREG(x)		(S3C_VA_SYS + (x))
 
diff --git a/arch/arm/mach-s5pv210/s5pv210.c b/arch/arm/mach-s5pv210/s5pv210.c
index 868f9c20419d..a21ed3bb992a 100644
--- a/arch/arm/mach-s5pv210/s5pv210.c
+++ b/arch/arm/mach-s5pv210/s5pv210.c
@@ -13,8 +13,6 @@
 #include <asm/mach/map.h>
 #include <asm/system_misc.h>
 
-#include <plat/map-base.h>
-
 #include "common.h"
 #include "regs-clock.h"
 
diff --git a/arch/arm/mach-shmobile/rcar-gen2.h b/arch/arm/mach-shmobile/rcar-gen2.h
index 4777fff2de41..af9dbd6aa49e 100644
--- a/arch/arm/mach-shmobile/rcar-gen2.h
+++ b/arch/arm/mach-shmobile/rcar-gen2.h
@@ -2,8 +2,6 @@
 #ifndef __ASM_RCAR_GEN2_H__
 #define __ASM_RCAR_GEN2_H__
 
-void rcar_gen2_timer_init(void);
-void rcar_gen2_reserve(void);
 void rcar_gen2_pm_init(void);
 
 #endif /* __ASM_RCAR_GEN2_H__ */
diff --git a/arch/arm/mach-shmobile/setup-rcar-gen2.c b/arch/arm/mach-shmobile/setup-rcar-gen2.c
index e00f5b3b9293..d42d93443f2f 100644
--- a/arch/arm/mach-shmobile/setup-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/setup-rcar-gen2.c
@@ -59,7 +59,7 @@ static unsigned int __init get_extal_freq(void)
 #define CNTCR 0
 #define CNTFID0 0x20
 
-void __init rcar_gen2_timer_init(void)
+static void __init rcar_gen2_timer_init(void)
 {
 	bool need_update = true;
 	void __iomem *base;
@@ -174,7 +174,7 @@ static int __init rcar_gen2_scan_mem(unsigned long node, const char *uname,
 	return 0;
 }
 
-void __init rcar_gen2_reserve(void)
+static void __init rcar_gen2_reserve(void)
 {
 	struct memory_reserve_config mrc;
 
diff --git a/arch/arm/mach-stm32/Makefile.boot b/arch/arm/mach-stm32/Makefile.boot
index cec195d4fcba..5dde7328a7a9 100644
--- a/arch/arm/mach-stm32/Makefile.boot
+++ b/arch/arm/mach-stm32/Makefile.boot
@@ -1,4 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 # Empty file waiting for deletion once Makefile.boot isn't needed any more.
 # Patch waits for application at
-# http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
+# https://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/plat-samsung/include/plat/adc.h b/arch/arm/plat-samsung/include/plat/adc.h
deleted file mode 100644
index 74d1a46408c1..000000000000
--- a/arch/arm/plat-samsung/include/plat/adc.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/	
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C ADC driver information
- */
-
-#ifndef __ASM_PLAT_ADC_H
-#define __ASM_PLAT_ADC_H __FILE__
-
-struct s3c_adc_client;
-struct platform_device;
-
-extern int s3c_adc_start(struct s3c_adc_client *client,
-			 unsigned int channel, unsigned int nr_samples);
-
-extern int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch);
-
-extern struct s3c_adc_client *
-	s3c_adc_register(struct platform_device *pdev,
-			 void (*select)(struct s3c_adc_client *client,
-					unsigned selected),
-			 void (*conv)(struct s3c_adc_client *client,
-				      unsigned d0, unsigned d1,
-				      unsigned *samples_left),
-			 unsigned int is_ts);
-
-extern void s3c_adc_release(struct s3c_adc_client *client);
-
-#endif /* __ASM_PLAT_ADC_H */
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
deleted file mode 100644
index 2c7cf2665634..000000000000
--- a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
+++ /dev/null
@@ -1,287 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2006-2009 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C CPU frequency scaling support - core support
- */
-
-#include <plat/cpu-freq.h>
-
-struct seq_file;
-
-#define MAX_BANKS (8)
-#define S3C2412_MAX_IO	(8)
-
-/**
- * struct s3c2410_iobank_timing - IO bank timings for S3C2410 style timings
- * @bankcon: The cached version of settings in this structure.
- * @tacp:
- * @tacs: Time from address valid to nCS asserted.
- * @tcos: Time from nCS asserted to nOE or nWE asserted.
- * @tacc: Time that nOE or nWE is asserted.
- * @tcoh: Time nCS is held after nOE or nWE are released.
- * @tcah: Time address is held for after
- * @nwait_en: Whether nWAIT is enabled for this bank.
- *
- * This structure represents the IO timings for a S3C2410 style IO bank
- * used by the CPU frequency support if it needs to change the settings
- * of the IO.
- */
-struct s3c2410_iobank_timing {
-	unsigned long	bankcon;
-	unsigned int	tacp;
-	unsigned int	tacs;
-	unsigned int	tcos;
-	unsigned int	tacc;
-	unsigned int	tcoh;		/* nCS hold after nOE/nWE */
-	unsigned int	tcah;		/* Address hold after nCS */
-	unsigned char	nwait_en;	/* nWait enabled for bank. */
-};
-
-/**
- * struct s3c2412_iobank_timing - io timings for PL092 (S3C2412) style IO
- * @idcy: The idle cycle time between transactions.
- * @wstrd: nCS release to end of read cycle.
- * @wstwr: nCS release to end of write cycle.
- * @wstoen: nCS assertion to nOE assertion time.
- * @wstwen: nCS assertion to nWE assertion time.
- * @wstbrd: Burst ready delay.
- * @smbidcyr: Register cache for smbidcyr value.
- * @smbwstrd: Register cache for smbwstrd value.
- * @smbwstwr: Register cache for smbwstwr value.
- * @smbwstoen: Register cache for smbwstoen value.
- * @smbwstwen: Register cache for smbwstwen value.
- * @smbwstbrd: Register cache for smbwstbrd value.
- *
- * Timing information for a IO bank on an S3C2412 or similar system which
- * uses a PL093 block.
- */
-struct s3c2412_iobank_timing {
-	unsigned int	idcy;
-	unsigned int	wstrd;
-	unsigned int	wstwr;
-	unsigned int	wstoen;
-	unsigned int	wstwen;
-	unsigned int	wstbrd;
-
-	/* register cache */
-	unsigned char	smbidcyr;
-	unsigned char	smbwstrd;
-	unsigned char	smbwstwr;
-	unsigned char	smbwstoen;
-	unsigned char	smbwstwen;
-	unsigned char	smbwstbrd;
-};
-
-union s3c_iobank {
-	struct s3c2410_iobank_timing	*io_2410;
-	struct s3c2412_iobank_timing	*io_2412;
-};
-
-/**
- * struct s3c_iotimings - Chip IO timings holder
- * @bank: The timings for each IO bank.
- */
-struct s3c_iotimings {
-	union s3c_iobank	bank[MAX_BANKS];
-};
-
-/**
- * struct s3c_plltab - PLL table information.
- * @vals: List of PLL values.
- * @size: Size of the PLL table @vals.
- */
-struct s3c_plltab {
-	struct s3c_pllval	*vals;
-	int			 size;
-};
-
-/**
- * struct s3c_cpufreq_config - current cpu frequency configuration
- * @freq: The current settings for the core clocks.
- * @max: Maxium settings, derived from core, board and user settings.
- * @pll: The PLL table entry for the current PLL settings.
- * @divs: The divisor settings for the core clocks.
- * @info: The current core driver information.
- * @board: The information for the board we are running on.
- * @lock_pll: Set if the PLL settings cannot be changed.
- *
- * This is for the core drivers that need to know information about
- * the current settings and values. It should not be needed by any
- * device drivers.
-*/
-struct s3c_cpufreq_config {
-	struct s3c_freq		freq;
-	struct s3c_freq		max;
-	struct clk		*mpll;
-	struct cpufreq_frequency_table pll;
-	struct s3c_clkdivs	divs;
-	struct s3c_cpufreq_info *info;	/* for core, not drivers */
-	struct s3c_cpufreq_board *board;
-
-	unsigned int	lock_pll:1;
-};
-
-/**
- * struct s3c_cpufreq_info - Information for the CPU frequency driver.
- * @name: The name of this implementation.
- * @max: The maximum frequencies for the system.
- * @latency: Transition latency to give to cpufreq.
- * @locktime_m: The lock-time in uS for the MPLL.
- * @locktime_u: The lock-time in uS for the UPLL.
- * @locttime_bits: The number of bits each LOCKTIME field.
- * @need_pll: Set if this driver needs to change the PLL values to achieve
- *	any frequency changes. This is really only need by devices like the
- *	S3C2410 where there is no or limited divider between the PLL and the
- *	ARMCLK.
- * @get_iotiming: Get the current IO timing data, mainly for use at start.
- * @set_iotiming: Update the IO timings from the cached copies calculated
- *	from the @calc_iotiming entry when changing the frequency.
- * @calc_iotiming: Calculate and update the cached copies of the IO timings
- *	from the newly calculated frequencies.
- * @calc_freqtable: Calculate (fill in) the given frequency table from the
- *	current frequency configuration. If the table passed in is NULL,
- *	then the return is the number of elements to be filled for allocation
- *	of the table.
- * @set_refresh: Set the memory refresh configuration.
- * @set_fvco: Set the PLL frequencies.
- * @set_divs: Update the clock divisors.
- * @calc_divs: Calculate the clock divisors.
- */
-struct s3c_cpufreq_info {
-	const char		*name;
-	struct s3c_freq		max;
-
-	unsigned int		latency;
-
-	unsigned int		locktime_m;
-	unsigned int		locktime_u;
-	unsigned char		locktime_bits;
-
-	unsigned int		need_pll:1;
-
-	/* driver routines */
-
-	int		(*get_iotiming)(struct s3c_cpufreq_config *cfg,
-					struct s3c_iotimings *timings);
-
-	void		(*set_iotiming)(struct s3c_cpufreq_config *cfg,
-					struct s3c_iotimings *timings);
-
-	int		(*calc_iotiming)(struct s3c_cpufreq_config *cfg,
-					 struct s3c_iotimings *timings);
-
-	int		(*calc_freqtable)(struct s3c_cpufreq_config *cfg,
-					  struct cpufreq_frequency_table *t,
-					  size_t table_size);
-
-	void		(*debug_io_show)(struct seq_file *seq,
-					 struct s3c_cpufreq_config *cfg,
-					 union s3c_iobank *iob);
-
-	void		(*set_refresh)(struct s3c_cpufreq_config *cfg);
-	void		(*set_fvco)(struct s3c_cpufreq_config *cfg);
-	void		(*set_divs)(struct s3c_cpufreq_config *cfg);
-	int		(*calc_divs)(struct s3c_cpufreq_config *cfg);
-};
-
-extern int s3c_cpufreq_register(struct s3c_cpufreq_info *info);
-
-extern int s3c_plltab_register(struct cpufreq_frequency_table *plls,
-			       unsigned int plls_no);
-
-/* exports and utilities for debugfs */
-extern struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void);
-extern struct s3c_iotimings *s3c_cpufreq_getiotimings(void);
-
-#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS
-#define s3c_cpufreq_debugfs_call(x) x
-#else
-#define s3c_cpufreq_debugfs_call(x) NULL
-#endif
-
-/* Useful utility functions. */
-
-extern struct clk *s3c_cpufreq_clk_get(struct device *, const char *);
-
-/* S3C2410 and compatible exported functions */
-
-extern void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg);
-extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg);
-
-#ifdef CONFIG_S3C2410_IOTIMING
-extern void s3c2410_iotiming_debugfs(struct seq_file *seq,
-				     struct s3c_cpufreq_config *cfg,
-				     union s3c_iobank *iob);
-
-extern int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg,
-				 struct s3c_iotimings *iot);
-
-extern int s3c2410_iotiming_get(struct s3c_cpufreq_config *cfg,
-				struct s3c_iotimings *timings);
-
-extern void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg,
-				 struct s3c_iotimings *iot);
-#else
-#define s3c2410_iotiming_debugfs NULL
-#define s3c2410_iotiming_calc NULL
-#define s3c2410_iotiming_get NULL
-#define s3c2410_iotiming_set NULL
-#endif /* CONFIG_S3C2410_IOTIMING */
-
-/* S3C2412 compatible routines */
-
-#ifdef CONFIG_S3C2412_IOTIMING
-extern void s3c2412_iotiming_debugfs(struct seq_file *seq,
-				     struct s3c_cpufreq_config *cfg,
-				     union s3c_iobank *iob);
-
-extern int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg,
-				struct s3c_iotimings *timings);
-
-extern int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg,
-				 struct s3c_iotimings *iot);
-
-extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg,
-				 struct s3c_iotimings *iot);
-#else
-#define s3c2412_iotiming_debugfs NULL
-#define s3c2412_iotiming_calc NULL
-#define s3c2412_iotiming_get NULL
-#define s3c2412_iotiming_set NULL
-#endif /* CONFIG_S3C2412_IOTIMING */
-
-#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG
-#define s3c_freq_dbg(x...) printk(KERN_INFO x)
-#else
-#define s3c_freq_dbg(x...) do { if (0) printk(x); } while (0)
-#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG */
-
-#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG
-#define s3c_freq_iodbg(x...) printk(KERN_INFO x)
-#else
-#define s3c_freq_iodbg(x...) do { if (0) printk(x); } while (0)
-#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG */
-
-static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table,
-				      int index, size_t table_size,
-				      unsigned int freq)
-{
-	if (index < 0)
-		return index;
-
-	if (table) {
-		if (index >= table_size)
-			return -ENOMEM;
-
-		s3c_freq_dbg("%s: { %d = %u kHz }\n",
-			     __func__, index, freq);
-
-		table[index].driver_data = index;
-		table[index].frequency = freq;
-	}
-
-	return index + 1;
-}
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq.h b/arch/arm/plat-samsung/include/plat/cpu-freq.h
deleted file mode 100644
index 558892bcf9b6..000000000000
--- a/arch/arm/plat-samsung/include/plat/cpu-freq.h
+++ /dev/null
@@ -1,141 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2006-2007 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C CPU frequency scaling support - driver and board
- */
-
-#include <linux/cpufreq.h>
-
-struct s3c_cpufreq_info;
-struct s3c_cpufreq_board;
-struct s3c_iotimings;
-
-/**
- * struct s3c_freq - frequency information (mainly for core drivers)
- * @fclk: The FCLK frequency in Hz.
- * @armclk: The ARMCLK frequency in Hz.
- * @hclk_tns: HCLK cycle time in 10ths of nano-seconds.
- * @hclk: The HCLK frequency in Hz.
- * @pclk: The PCLK frequency in Hz.
- *
- * This contains the frequency information about the current configuration
- * mainly for the core drivers to ensure we do not end up passing about
- * a large number of parameters.
- *
- * The @hclk_tns field is a useful cache for the parts of the drivers that
- * need to calculate IO timings and suchlike.
- */
-struct s3c_freq {
-	unsigned long	fclk;
-	unsigned long	armclk;
-	unsigned long	hclk_tns;	/* in 10ths of ns */
-	unsigned long	hclk;
-	unsigned long	pclk;
-};
-
-/**
- * struct s3c_cpufreq_freqs - s3c cpufreq notification information.
- * @freqs: The cpufreq setting information.
- * @old: The old clock settings.
- * @new: The new clock settings.
- * @pll_changing: Set if the PLL is changing.
- *
- * Wrapper 'struct cpufreq_freqs' so that any drivers receiving the
- * notification can use this information that is not provided by just
- * having the core frequency alone.
- *
- * The pll_changing flag is used to indicate if the PLL itself is
- * being set during this change. This is important as the clocks
- * will temporarily be set to the XTAL clock during this time, so
- * drivers may want to close down their output during this time.
- *
- * Note, this is not being used by any current drivers and therefore
- * may be removed in the future.
- */
-struct s3c_cpufreq_freqs {
-	struct cpufreq_freqs	freqs;
-	struct s3c_freq		old;
-	struct s3c_freq		new;
-
-	unsigned int		pll_changing:1;
-};
-
-#define to_s3c_cpufreq(_cf) container_of(_cf, struct s3c_cpufreq_freqs, freqs)
-
-/**
- * struct s3c_clkdivs - clock divisor information
- * @p_divisor: Divisor from FCLK to PCLK.
- * @h_divisor: Divisor from FCLK to HCLK.
- * @arm_divisor: Divisor from FCLK to ARMCLK (not all CPUs).
- * @dvs: Non-zero if using DVS mode for ARMCLK.
- *
- * Divisor settings for the core clocks.
- */
-struct s3c_clkdivs {
-	int		p_divisor;
-	int		h_divisor;
-	int		arm_divisor;
-	unsigned char	dvs;
-};
-
-#define PLLVAL(_m, _p, _s) (((_m) << 12) | ((_p) << 4) | (_s))
-
-/**
- * struct s3c_pllval - PLL value entry.
- * @freq: The frequency for this entry in Hz.
- * @pll_reg: The PLL register setting for this PLL value.
- */
-struct s3c_pllval {
-	unsigned long		freq;
-	unsigned long		pll_reg;
-};
-
-/**
- * struct s3c_cpufreq_board - per-board cpu frequency informatin
- * @refresh: The SDRAM refresh period in nanoseconds.
- * @auto_io: Set if the IO timing settings should be generated from the
- *	initialisation time hardware registers.
- * @need_io: Set if the board has external IO on any of the chipselect
- *	lines that will require the hardware timing registers to be
- *	updated on a clock change.
- * @max: The maxium frequency limits for the system. Any field that
- *	is left at zero will use the CPU's settings.
- *
- * This contains the board specific settings that affect how the CPU
- * drivers chose settings. These include the memory refresh and IO
- * timing information.
- *
- * Registration depends on the driver being used, the ARMCLK only
- * implementation does not currently need this but the older style
- * driver requires this to be available.
- */
-struct s3c_cpufreq_board {
-	unsigned int	refresh;
-	unsigned int	auto_io:1;	/* automatically init io timings. */
-	unsigned int	need_io:1;	/* set if needs io timing support. */
-
-	/* any non-zero field in here is taken as an upper limit. */
-	struct s3c_freq	max;	/* frequency limits */
-};
-
-/* Things depending on frequency scaling. */
-#ifdef CONFIG_ARM_S3C_CPUFREQ
-#define __init_or_cpufreq
-#else
-#define __init_or_cpufreq __init
-#endif
-
-/* Board functions */
-
-#ifdef CONFIG_ARM_S3C_CPUFREQ
-extern int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board);
-#else
-
-static inline int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board)
-{
-	return 0;
-}
-#endif  /* CONFIG_ARM_S3C_CPUFREQ */
diff --git a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
deleted file mode 100644
index 614240d768b4..000000000000
--- a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
+++ /dev/null
@@ -1,68 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2004 Arnaud Patard <arnaud.patard@rtp-net.org>
- *
- * Inspired by pxafb.h
-*/
-
-#ifndef __ASM_PLAT_FB_S3C2410_H
-#define __ASM_PLAT_FB_S3C2410_H __FILE__
-
-struct s3c2410fb_hw {
-	unsigned long	lcdcon1;
-	unsigned long	lcdcon2;
-	unsigned long	lcdcon3;
-	unsigned long	lcdcon4;
-	unsigned long	lcdcon5;
-};
-
-/* LCD description */
-struct s3c2410fb_display {
-	/* LCD type */
-	unsigned type;
-
-	/* Screen size */
-	unsigned short width;
-	unsigned short height;
-
-	/* Screen info */
-	unsigned short xres;
-	unsigned short yres;
-	unsigned short bpp;
-
-	unsigned pixclock;		/* pixclock in picoseconds */
-	unsigned short left_margin;  /* value in pixels (TFT) or HCLKs (STN) */
-	unsigned short right_margin; /* value in pixels (TFT) or HCLKs (STN) */
-	unsigned short hsync_len;    /* value in pixels (TFT) or HCLKs (STN) */
-	unsigned short upper_margin;	/* value in lines (TFT) or 0 (STN) */
-	unsigned short lower_margin;	/* value in lines (TFT) or 0 (STN) */
-	unsigned short vsync_len;	/* value in lines (TFT) or 0 (STN) */
-
-	/* lcd configuration registers */
-	unsigned long	lcdcon5;
-};
-
-struct s3c2410fb_mach_info {
-
-	struct s3c2410fb_display *displays;	/* attached displays info */
-	unsigned num_displays;			/* number of defined displays */
-	unsigned default_display;
-
-	/* GPIOs */
-
-	unsigned long	gpcup;
-	unsigned long	gpcup_mask;
-	unsigned long	gpccon;
-	unsigned long	gpccon_mask;
-	unsigned long	gpdup;
-	unsigned long	gpdup_mask;
-	unsigned long	gpdcon;
-	unsigned long	gpdcon_mask;
-
-	/* lpc3600 control register */
-	unsigned long	lpcsel;
-};
-
-extern void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *);
-
-#endif /* __ASM_PLAT_FB_S3C2410_H */
diff --git a/arch/arm/plat-samsung/include/plat/pm-common.h b/arch/arm/plat-samsung/include/plat/pm-common.h
deleted file mode 100644
index 1268bae04234..000000000000
--- a/arch/arm/plat-samsung/include/plat/pm-common.h
+++ /dev/null
@@ -1,107 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) 2013 Samsung Electronics Co., Ltd.
- *	Tomasz Figa <t.figa@samsung.com>
- * Copyright (c) 2004 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Written by Ben Dooks, <ben@simtec.co.uk>
- */
-
-#ifndef __PLAT_SAMSUNG_PM_COMMON_H
-#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
-
-#include <linux/irq.h>
-
-/* sleep save info */
-
-/**
- * struct sleep_save - save information for shared peripherals.
- * @reg: Pointer to the register to save.
- * @val: Holder for the value saved from reg.
- *
- * This describes a list of registers which is used by the pm core and
- * other subsystem to save and restore register values over suspend.
- */
-struct sleep_save {
-	void __iomem	*reg;
-	unsigned long	val;
-};
-
-#define SAVE_ITEM(x) \
-	{ .reg = (x) }
-
-/* helper functions to save/restore lists of registers. */
-
-extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
-
-/* PM debug functions */
-
-/**
- * struct pm_uart_save - save block for core UART
- * @ulcon: Save value for S3C2410_ULCON
- * @ucon: Save value for S3C2410_UCON
- * @ufcon: Save value for S3C2410_UFCON
- * @umcon: Save value for S3C2410_UMCON
- * @ubrdiv: Save value for S3C2410_UBRDIV
- *
- * Save block for UART registers to be held over sleep and restored if they
- * are needed (say by debug).
-*/
-struct pm_uart_save {
-	u32	ulcon;
-	u32	ucon;
-	u32	ufcon;
-	u32	umcon;
-	u32	ubrdiv;
-	u32	udivslot;
-};
-
-#ifdef CONFIG_SAMSUNG_PM_DEBUG
-/**
- * s3c_pm_dbg() - low level debug function for use in suspend/resume.
- * @msg: The message to print.
- *
- * This function is used mainly to debug the resume process before the system
- * can rely on printk/console output. It uses the low-level debugging output
- * routine printascii() to do its work.
- */
-extern void s3c_pm_dbg(const char *msg, ...);
-
-/**
- * s3c_pm_debug_init() - suspend/resume low level debug initialization.
- * @base: Virtual base of UART to use for suspend/resume debugging.
- *
- * This function needs to be called before S3C_PMDBG() can be used, to set up
- * UART port base address and configuration.
- */
-extern void s3c_pm_debug_init(void);
-
-#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
-
-extern void s3c_pm_save_uarts(void);
-extern void s3c_pm_restore_uarts(void);
-#else
-#define S3C_PMDBG(fmt...) pr_debug(fmt)
-#define s3c_pm_debug_init() do { } while (0)
-
-static inline void s3c_pm_save_uarts(void) { }
-static inline void s3c_pm_restore_uarts(void) { }
-#endif
-
-/* suspend memory checking */
-
-#ifdef CONFIG_SAMSUNG_PM_CHECK
-extern void s3c_pm_check_prepare(void);
-extern void s3c_pm_check_restore(void);
-extern void s3c_pm_check_cleanup(void);
-extern void s3c_pm_check_store(void);
-#else
-#define s3c_pm_check_prepare() do { } while (0)
-#define s3c_pm_check_restore() do { } while (0)
-#define s3c_pm_check_cleanup() do { } while (0)
-#define s3c_pm_check_store()   do { } while (0)
-#endif
-
-#endif
diff --git a/arch/arm/plat-samsung/include/plat/regs-spi.h b/arch/arm/plat-samsung/include/plat/regs-spi.h
deleted file mode 100644
index 607844311566..000000000000
--- a/arch/arm/plat-samsung/include/plat/regs-spi.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2004 Fetron GmbH
- *
- * S3C2410 SPI register definition
- */
-
-#ifndef __ASM_ARCH_REGS_SPI_H
-#define __ASM_ARCH_REGS_SPI_H
-
-#define S3C2410_SPI1		(0x20)
-#define S3C2412_SPI1		(0x100)
-
-#define S3C2410_SPCON		(0x00)
-
-#define S3C2410_SPCON_SMOD_DMA	(2 << 5)	/* DMA mode */
-#define S3C2410_SPCON_SMOD_INT	(1 << 5)	/* interrupt mode */
-#define S3C2410_SPCON_SMOD_POLL	(0 << 5)	/* polling mode */
-#define S3C2410_SPCON_ENSCK	(1 << 4)	/* Enable SCK */
-#define S3C2410_SPCON_MSTR	(1 << 3)	/* Master:1, Slave:0 select */
-#define S3C2410_SPCON_CPOL_HIGH	(1 << 2)	/* Clock polarity select */
-#define S3C2410_SPCON_CPOL_LOW	(0 << 2)	/* Clock polarity select */
-
-#define S3C2410_SPCON_CPHA_FMTB	(1 << 1)	/* Clock Phase Select */
-#define S3C2410_SPCON_CPHA_FMTA	(0 << 1)	/* Clock Phase Select */
-
-#define S3C2410_SPSTA		(0x04)
-
-#define S3C2410_SPSTA_DCOL	(1 << 2)	/* Data Collision Error */
-#define S3C2410_SPSTA_MULD	(1 << 1)	/* Multi Master Error */
-#define S3C2410_SPSTA_READY	(1 << 0)	/* Data Tx/Rx ready */
-#define S3C2412_SPSTA_READY_ORG	(1 << 3)
-
-#define S3C2410_SPPIN		(0x08)
-
-#define S3C2410_SPPIN_ENMUL	(1 << 2)	/* Multi Master Error detect */
-#define S3C2410_SPPIN_RESERVED	(1 << 1)
-#define S3C2410_SPPIN_KEEP	(1 << 0)	/* Master Out keep */
-
-#define S3C2410_SPPRE		(0x0C)
-#define S3C2410_SPTDAT		(0x10)
-#define S3C2410_SPRDAT		(0x14)
-
-#endif /* __ASM_ARCH_REGS_SPI_H */
diff --git a/arch/arm/plat-samsung/include/plat/regs-udc.h b/arch/arm/plat-samsung/include/plat/regs-udc.h
deleted file mode 100644
index d8d2eeaca088..000000000000
--- a/arch/arm/plat-samsung/include/plat/regs-udc.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2004 Herbert Poetzl <herbert@13thfloor.at>
- */
-
-#ifndef __ASM_ARCH_REGS_UDC_H
-#define __ASM_ARCH_REGS_UDC_H
-
-#define S3C2410_USBDREG(x) (x)
-
-#define S3C2410_UDC_FUNC_ADDR_REG	S3C2410_USBDREG(0x0140)
-#define S3C2410_UDC_PWR_REG		S3C2410_USBDREG(0x0144)
-#define S3C2410_UDC_EP_INT_REG		S3C2410_USBDREG(0x0148)
-
-#define S3C2410_UDC_USB_INT_REG		S3C2410_USBDREG(0x0158)
-#define S3C2410_UDC_EP_INT_EN_REG	S3C2410_USBDREG(0x015c)
-
-#define S3C2410_UDC_USB_INT_EN_REG	S3C2410_USBDREG(0x016c)
-
-#define S3C2410_UDC_FRAME_NUM1_REG	S3C2410_USBDREG(0x0170)
-#define S3C2410_UDC_FRAME_NUM2_REG	S3C2410_USBDREG(0x0174)
-
-#define S3C2410_UDC_EP0_FIFO_REG	S3C2410_USBDREG(0x01c0)
-#define S3C2410_UDC_EP1_FIFO_REG	S3C2410_USBDREG(0x01c4)
-#define S3C2410_UDC_EP2_FIFO_REG	S3C2410_USBDREG(0x01c8)
-#define S3C2410_UDC_EP3_FIFO_REG	S3C2410_USBDREG(0x01cc)
-#define S3C2410_UDC_EP4_FIFO_REG	S3C2410_USBDREG(0x01d0)
-
-#define S3C2410_UDC_EP1_DMA_CON		S3C2410_USBDREG(0x0200)
-#define S3C2410_UDC_EP1_DMA_UNIT	S3C2410_USBDREG(0x0204)
-#define S3C2410_UDC_EP1_DMA_FIFO	S3C2410_USBDREG(0x0208)
-#define S3C2410_UDC_EP1_DMA_TTC_L	S3C2410_USBDREG(0x020c)
-#define S3C2410_UDC_EP1_DMA_TTC_M	S3C2410_USBDREG(0x0210)
-#define S3C2410_UDC_EP1_DMA_TTC_H	S3C2410_USBDREG(0x0214)
-
-#define S3C2410_UDC_EP2_DMA_CON		S3C2410_USBDREG(0x0218)
-#define S3C2410_UDC_EP2_DMA_UNIT	S3C2410_USBDREG(0x021c)
-#define S3C2410_UDC_EP2_DMA_FIFO	S3C2410_USBDREG(0x0220)
-#define S3C2410_UDC_EP2_DMA_TTC_L	S3C2410_USBDREG(0x0224)
-#define S3C2410_UDC_EP2_DMA_TTC_M	S3C2410_USBDREG(0x0228)
-#define S3C2410_UDC_EP2_DMA_TTC_H	S3C2410_USBDREG(0x022c)
-
-#define S3C2410_UDC_EP3_DMA_CON		S3C2410_USBDREG(0x0240)
-#define S3C2410_UDC_EP3_DMA_UNIT	S3C2410_USBDREG(0x0244)
-#define S3C2410_UDC_EP3_DMA_FIFO	S3C2410_USBDREG(0x0248)
-#define S3C2410_UDC_EP3_DMA_TTC_L	S3C2410_USBDREG(0x024c)
-#define S3C2410_UDC_EP3_DMA_TTC_M	S3C2410_USBDREG(0x0250)
-#define S3C2410_UDC_EP3_DMA_TTC_H	S3C2410_USBDREG(0x0254)
-
-#define S3C2410_UDC_EP4_DMA_CON		S3C2410_USBDREG(0x0258)
-#define S3C2410_UDC_EP4_DMA_UNIT	S3C2410_USBDREG(0x025c)
-#define S3C2410_UDC_EP4_DMA_FIFO	S3C2410_USBDREG(0x0260)
-#define S3C2410_UDC_EP4_DMA_TTC_L	S3C2410_USBDREG(0x0264)
-#define S3C2410_UDC_EP4_DMA_TTC_M	S3C2410_USBDREG(0x0268)
-#define S3C2410_UDC_EP4_DMA_TTC_H	S3C2410_USBDREG(0x026c)
-
-#define S3C2410_UDC_INDEX_REG		S3C2410_USBDREG(0x0178)
-
-/* indexed registers */
-
-#define S3C2410_UDC_MAXP_REG		S3C2410_USBDREG(0x0180)
-
-#define S3C2410_UDC_EP0_CSR_REG		S3C2410_USBDREG(0x0184)
-
-#define S3C2410_UDC_IN_CSR1_REG		S3C2410_USBDREG(0x0184)
-#define S3C2410_UDC_IN_CSR2_REG		S3C2410_USBDREG(0x0188)
-
-#define S3C2410_UDC_OUT_CSR1_REG	S3C2410_USBDREG(0x0190)
-#define S3C2410_UDC_OUT_CSR2_REG	S3C2410_USBDREG(0x0194)
-#define S3C2410_UDC_OUT_FIFO_CNT1_REG	S3C2410_USBDREG(0x0198)
-#define S3C2410_UDC_OUT_FIFO_CNT2_REG	S3C2410_USBDREG(0x019c)
-
-#define S3C2410_UDC_FUNCADDR_UPDATE	(1 << 7)
-
-#define S3C2410_UDC_PWR_ISOUP		(1 << 7) /* R/W */
-#define S3C2410_UDC_PWR_RESET		(1 << 3) /* R   */
-#define S3C2410_UDC_PWR_RESUME		(1 << 2) /* R/W */
-#define S3C2410_UDC_PWR_SUSPEND		(1 << 1) /* R   */
-#define S3C2410_UDC_PWR_ENSUSPEND	(1 << 0) /* R/W */
-
-#define S3C2410_UDC_PWR_DEFAULT		(0x00)
-
-#define S3C2410_UDC_INT_EP4		(1 << 4) /* R/W (clear only) */
-#define S3C2410_UDC_INT_EP3		(1 << 3) /* R/W (clear only) */
-#define S3C2410_UDC_INT_EP2		(1 << 2) /* R/W (clear only) */
-#define S3C2410_UDC_INT_EP1		(1 << 1) /* R/W (clear only) */
-#define S3C2410_UDC_INT_EP0		(1 << 0) /* R/W (clear only) */
-
-#define S3C2410_UDC_USBINT_RESET	(1 << 2) /* R/W (clear only) */
-#define S3C2410_UDC_USBINT_RESUME	(1 << 1) /* R/W (clear only) */
-#define S3C2410_UDC_USBINT_SUSPEND	(1 << 0) /* R/W (clear only) */
-
-#define S3C2410_UDC_INTE_EP4		(1 << 4) /* R/W */
-#define S3C2410_UDC_INTE_EP3		(1 << 3) /* R/W */
-#define S3C2410_UDC_INTE_EP2		(1 << 2) /* R/W */
-#define S3C2410_UDC_INTE_EP1		(1 << 1) /* R/W */
-#define S3C2410_UDC_INTE_EP0		(1 << 0) /* R/W */
-
-#define S3C2410_UDC_USBINTE_RESET	(1 << 2) /* R/W */
-#define S3C2410_UDC_USBINTE_SUSPEND	(1 << 0) /* R/W */
-
-#define S3C2410_UDC_INDEX_EP0		(0x00)
-#define S3C2410_UDC_INDEX_EP1		(0x01)
-#define S3C2410_UDC_INDEX_EP2		(0x02)
-#define S3C2410_UDC_INDEX_EP3		(0x03)
-#define S3C2410_UDC_INDEX_EP4		(0x04)
-
-#define S3C2410_UDC_ICSR1_CLRDT		(1 << 6) /* R/W */
-#define S3C2410_UDC_ICSR1_SENTSTL	(1 << 5) /* R/W (clear only) */
-#define S3C2410_UDC_ICSR1_SENDSTL	(1 << 4) /* R/W */
-#define S3C2410_UDC_ICSR1_FFLUSH	(1 << 3) /* W   (set only) */
-#define S3C2410_UDC_ICSR1_UNDRUN	(1 << 2) /* R/W (clear only) */
-#define S3C2410_UDC_ICSR1_PKTRDY	(1 << 0) /* R/W (set only) */
-
-#define S3C2410_UDC_ICSR2_AUTOSET	(1 << 7) /* R/W */
-#define S3C2410_UDC_ICSR2_ISO		(1 << 6) /* R/W */
-#define S3C2410_UDC_ICSR2_MODEIN	(1 << 5) /* R/W */
-#define S3C2410_UDC_ICSR2_DMAIEN	(1 << 4) /* R/W */
-
-#define S3C2410_UDC_OCSR1_CLRDT		(1 << 7) /* R/W */
-#define S3C2410_UDC_OCSR1_SENTSTL	(1 << 6) /* R/W (clear only) */
-#define S3C2410_UDC_OCSR1_SENDSTL	(1 << 5) /* R/W */
-#define S3C2410_UDC_OCSR1_FFLUSH	(1 << 4) /* R/W */
-#define S3C2410_UDC_OCSR1_DERROR	(1 << 3) /* R   */
-#define S3C2410_UDC_OCSR1_OVRRUN	(1 << 2) /* R/W (clear only) */
-#define S3C2410_UDC_OCSR1_PKTRDY	(1 << 0) /* R/W (clear only) */
-
-#define S3C2410_UDC_OCSR2_AUTOCLR	(1 << 7) /* R/W */
-#define S3C2410_UDC_OCSR2_ISO		(1 << 6) /* R/W */
-#define S3C2410_UDC_OCSR2_DMAIEN	(1 << 5) /* R/W */
-
-#define S3C2410_UDC_EP0_CSR_OPKRDY	(1 << 0)
-#define S3C2410_UDC_EP0_CSR_IPKRDY	(1 << 1)
-#define S3C2410_UDC_EP0_CSR_SENTSTL	(1 << 2)
-#define S3C2410_UDC_EP0_CSR_DE		(1 << 3)
-#define S3C2410_UDC_EP0_CSR_SE		(1 << 4)
-#define S3C2410_UDC_EP0_CSR_SENDSTL	(1 << 5)
-#define S3C2410_UDC_EP0_CSR_SOPKTRDY	(1 << 6)
-#define S3C2410_UDC_EP0_CSR_SSE		(1 << 7)
-
-#define S3C2410_UDC_MAXP_8		(1 << 0)
-#define S3C2410_UDC_MAXP_16		(1 << 1)
-#define S3C2410_UDC_MAXP_32		(1 << 2)
-#define S3C2410_UDC_MAXP_64		(1 << 3)
-
-#endif
diff --git a/arch/arm/plat-samsung/include/plat/samsung-time.h b/arch/arm/plat-samsung/include/plat/samsung-time.h
deleted file mode 100644
index 32ab0860f631..000000000000
--- a/arch/arm/plat-samsung/include/plat/samsung-time.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright 2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * Header file for samsung s3c and s5p time support
- */
-
-#ifndef __ASM_PLAT_SAMSUNG_TIME_H
-#define __ASM_PLAT_SAMSUNG_TIME_H __FILE__
-
-/* Samsung HR-Timer Clock mode */
-enum samsung_timer_mode {
-	SAMSUNG_PWM0,
-	SAMSUNG_PWM1,
-	SAMSUNG_PWM2,
-	SAMSUNG_PWM3,
-	SAMSUNG_PWM4,
-};
-
-extern void __init samsung_set_timer_source(enum samsung_timer_mode event,
-					enum samsung_timer_mode source);
-
-extern void __init samsung_timer_init(void);
-
-#endif /* __ASM_PLAT_SAMSUNG_TIME_H */
diff --git a/arch/arm/plat-samsung/pm-check.c b/arch/arm/plat-samsung/pm-check.c
deleted file mode 100644
index cd2c02c68bc3..000000000000
--- a/arch/arm/plat-samsung/pm-check.c
+++ /dev/null
@@ -1,233 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// originally in linux/arch/arm/plat-s3c24xx/pm.c
-//
-// Copyright (c) 2004-2008 Simtec Electronics
-//	http://armlinux.simtec.co.uk
-//	Ben Dooks <ben@simtec.co.uk>
-//
-// S3C Power Mangament - suspend/resume memory corruption check.
-
-#include <linux/kernel.h>
-#include <linux/suspend.h>
-#include <linux/init.h>
-#include <linux/crc32.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-
-#include <plat/pm-common.h>
-
-#if CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE < 1
-#error CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE must be a positive non-zero value
-#endif
-
-/* suspend checking code...
- *
- * this next area does a set of crc checks over all the installed
- * memory, so the system can verify if the resume was ok.
- *
- * CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE defines the block-size for the CRC,
- * increasing it will mean that the area corrupted will be less easy to spot,
- * and reducing the size will cause the CRC save area to grow
-*/
-
-#define CHECK_CHUNKSIZE (CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE * 1024)
-
-static u32 crc_size;	/* size needed for the crc block */
-static u32 *crcs;	/* allocated over suspend/resume */
-
-typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg);
-
-/* s3c_pm_run_res
- *
- * go through the given resource list, and look for system ram
-*/
-
-static void s3c_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg)
-{
-	while (ptr != NULL) {
-		if (ptr->child != NULL)
-			s3c_pm_run_res(ptr->child, fn, arg);
-
-		if ((ptr->flags & IORESOURCE_SYSTEM_RAM)
-				== IORESOURCE_SYSTEM_RAM) {
-			S3C_PMDBG("Found system RAM at %08lx..%08lx\n",
-				  (unsigned long)ptr->start,
-				  (unsigned long)ptr->end);
-			arg = (fn)(ptr, arg);
-		}
-
-		ptr = ptr->sibling;
-	}
-}
-
-static void s3c_pm_run_sysram(run_fn_t fn, u32 *arg)
-{
-	s3c_pm_run_res(&iomem_resource, fn, arg);
-}
-
-static u32 *s3c_pm_countram(struct resource *res, u32 *val)
-{
-	u32 size = (u32)resource_size(res);
-
-	size += CHECK_CHUNKSIZE-1;
-	size /= CHECK_CHUNKSIZE;
-
-	S3C_PMDBG("Area %08lx..%08lx, %d blocks\n",
-		  (unsigned long)res->start, (unsigned long)res->end, size);
-
-	*val += size * sizeof(u32);
-	return val;
-}
-
-/* s3c_pm_prepare_check
- *
- * prepare the necessary information for creating the CRCs. This
- * must be done before the final save, as it will require memory
- * allocating, and thus touching bits of the kernel we do not
- * know about.
-*/
-
-void s3c_pm_check_prepare(void)
-{
-	crc_size = 0;
-
-	s3c_pm_run_sysram(s3c_pm_countram, &crc_size);
-
-	S3C_PMDBG("s3c_pm_prepare_check: %u checks needed\n", crc_size);
-
-	crcs = kmalloc(crc_size+4, GFP_KERNEL);
-	if (crcs == NULL)
-		printk(KERN_ERR "Cannot allocated CRC save area\n");
-}
-
-static u32 *s3c_pm_makecheck(struct resource *res, u32 *val)
-{
-	unsigned long addr, left;
-
-	for (addr = res->start; addr < res->end;
-	     addr += CHECK_CHUNKSIZE) {
-		left = res->end - addr;
-
-		if (left > CHECK_CHUNKSIZE)
-			left = CHECK_CHUNKSIZE;
-
-		*val = crc32_le(~0, phys_to_virt(addr), left);
-		val++;
-	}
-
-	return val;
-}
-
-/* s3c_pm_check_store
- *
- * compute the CRC values for the memory blocks before the final
- * sleep.
-*/
-
-void s3c_pm_check_store(void)
-{
-	if (crcs != NULL)
-		s3c_pm_run_sysram(s3c_pm_makecheck, crcs);
-}
-
-/* in_region
- *
- * return TRUE if the area defined by ptr..ptr+size contains the
- * what..what+whatsz
-*/
-
-static inline int in_region(void *ptr, int size, void *what, size_t whatsz)
-{
-	if ((what+whatsz) < ptr)
-		return 0;
-
-	if (what > (ptr+size))
-		return 0;
-
-	return 1;
-}
-
-/**
- * s3c_pm_runcheck() - helper to check a resource on restore.
- * @res: The resource to check
- * @vak: Pointer to list of CRC32 values to check.
- *
- * Called from the s3c_pm_check_restore() via s3c_pm_run_sysram(), this
- * function runs the given memory resource checking it against the stored
- * CRC to ensure that memory is restored. The function tries to skip as
- * many of the areas used during the suspend process.
- */
-static u32 *s3c_pm_runcheck(struct resource *res, u32 *val)
-{
-	unsigned long addr;
-	unsigned long left;
-	void *stkpage;
-	void *ptr;
-	u32 calc;
-
-	stkpage = (void *)((u32)&calc & ~PAGE_MASK);
-
-	for (addr = res->start; addr < res->end;
-	     addr += CHECK_CHUNKSIZE) {
-		left = res->end - addr;
-
-		if (left > CHECK_CHUNKSIZE)
-			left = CHECK_CHUNKSIZE;
-
-		ptr = phys_to_virt(addr);
-
-		if (in_region(ptr, left, stkpage, 4096)) {
-			S3C_PMDBG("skipping %08lx, has stack in\n", addr);
-			goto skip_check;
-		}
-
-		if (in_region(ptr, left, crcs, crc_size)) {
-			S3C_PMDBG("skipping %08lx, has crc block in\n", addr);
-			goto skip_check;
-		}
-
-		/* calculate and check the checksum */
-
-		calc = crc32_le(~0, ptr, left);
-		if (calc != *val) {
-			printk(KERN_ERR "Restore CRC error at "
-			       "%08lx (%08x vs %08x)\n", addr, calc, *val);
-
-			S3C_PMDBG("Restore CRC error at %08lx (%08x vs %08x)\n",
-			    addr, calc, *val);
-		}
-
-	skip_check:
-		val++;
-	}
-
-	return val;
-}
-
-/**
- * s3c_pm_check_restore() - memory check called on resume
- *
- * check the CRCs after the restore event and free the memory used
- * to hold them
-*/
-void s3c_pm_check_restore(void)
-{
-	if (crcs != NULL)
-		s3c_pm_run_sysram(s3c_pm_runcheck, crcs);
-}
-
-/**
- * s3c_pm_check_cleanup() - free memory resources
- *
- * Free the resources that where allocated by the suspend
- * memory check code. We do this separately from the
- * s3c_pm_check_restore() function as we cannot call any
- * functions that might sleep during that resume.
- */
-void s3c_pm_check_cleanup(void)
-{
-	kfree(crcs);
-	crcs = NULL;
-}
-
diff --git a/arch/arm/plat-samsung/pm-debug.c b/arch/arm/plat-samsung/pm-debug.c
deleted file mode 100644
index b76b1e9ba4ae..000000000000
--- a/arch/arm/plat-samsung/pm-debug.c
+++ /dev/null
@@ -1,95 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (C) 2013 Samsung Electronics Co., Ltd.
-//	Tomasz Figa <t.figa@samsung.com>
-// Copyright (C) 2008 Openmoko, Inc.
-// Copyright (C) 2004-2008 Simtec Electronics
-//	Ben Dooks <ben@simtec.co.uk>
-//	http://armlinux.simtec.co.uk/
-//
-// Samsung common power management (suspend to RAM) debug support
-
-#include <linux/serial_core.h>
-#include <linux/serial_s3c.h>
-#include <linux/io.h>
-
-#include <asm/mach/map.h>
-
-#include <plat/cpu.h>
-#include <plat/pm-common.h>
-
-#ifdef CONFIG_SAMSUNG_ATAGS
-#include <plat/pm.h>
-#include <mach/pm-core.h>
-#else
-static inline void s3c_pm_debug_init_uart(void) {}
-static inline void s3c_pm_arch_update_uart(void __iomem *regs,
-					   struct pm_uart_save *save) {}
-#endif
-
-static struct pm_uart_save uart_save;
-
-extern void printascii(const char *);
-
-void s3c_pm_dbg(const char *fmt, ...)
-{
-	va_list va;
-	char buff[256];
-
-	va_start(va, fmt);
-	vsnprintf(buff, sizeof(buff), fmt, va);
-	va_end(va);
-
-	printascii(buff);
-}
-
-void s3c_pm_debug_init(void)
-{
-	/* restart uart clocks so we can use them to output */
-	s3c_pm_debug_init_uart();
-}
-
-static inline void __iomem *s3c_pm_uart_base(void)
-{
-	unsigned long paddr;
-	unsigned long vaddr;
-
-	debug_ll_addr(&paddr, &vaddr);
-
-	return (void __iomem *)vaddr;
-}
-
-void s3c_pm_save_uarts(void)
-{
-	void __iomem *regs = s3c_pm_uart_base();
-	struct pm_uart_save *save = &uart_save;
-
-	save->ulcon = __raw_readl(regs + S3C2410_ULCON);
-	save->ucon = __raw_readl(regs + S3C2410_UCON);
-	save->ufcon = __raw_readl(regs + S3C2410_UFCON);
-	save->umcon = __raw_readl(regs + S3C2410_UMCON);
-	save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
-
-	if (!soc_is_s3c2410())
-		save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
-
-	S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
-		  regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
-}
-
-void s3c_pm_restore_uarts(void)
-{
-	void __iomem *regs = s3c_pm_uart_base();
-	struct pm_uart_save *save = &uart_save;
-
-	s3c_pm_arch_update_uart(regs, save);
-
-	__raw_writel(save->ulcon, regs + S3C2410_ULCON);
-	__raw_writel(save->ucon,  regs + S3C2410_UCON);
-	__raw_writel(save->ufcon, regs + S3C2410_UFCON);
-	__raw_writel(save->umcon, regs + S3C2410_UMCON);
-	__raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
-
-	if (!soc_is_s3c2410())
-		__raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
-}
diff --git a/arch/arm/plat-samsung/watchdog-reset.c b/arch/arm/plat-samsung/watchdog-reset.c
deleted file mode 100644
index 71d85ff323f7..000000000000
--- a/arch/arm/plat-samsung/watchdog-reset.c
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (c) 2008 Simtec Electronics
-//	Ben Dooks <ben@simtec.co.uk>
-//
-// Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
-//
-// Watchdog reset support for Samsung SoCs.
-
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#define S3C2410_WTCON			0x00
-#define S3C2410_WTDAT			0x04
-#define S3C2410_WTCNT			0x08
-
-#define S3C2410_WTCON_ENABLE		(1 << 5)
-#define S3C2410_WTCON_DIV16		(0 << 3)
-#define S3C2410_WTCON_RSTEN		(1 << 0)
-#define S3C2410_WTCON_PRESCALE(x)	((x) << 8)
-
-static void __iomem *wdt_base;
-static struct clk *wdt_clock;
-
-void samsung_wdt_reset(void)
-{
-	if (!wdt_base) {
-		pr_err("%s: wdt reset not initialized\n", __func__);
-		/* delay to allow the serial port to show the message */
-		mdelay(50);
-		return;
-	}
-
-	if (!IS_ERR(wdt_clock))
-		clk_prepare_enable(wdt_clock);
-
-	/* disable watchdog, to be safe  */
-	__raw_writel(0, wdt_base + S3C2410_WTCON);
-
-	/* put initial values into count and data */
-	__raw_writel(0x80, wdt_base + S3C2410_WTCNT);
-	__raw_writel(0x80, wdt_base + S3C2410_WTDAT);
-
-	/* set the watchdog to go and reset... */
-	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV16 |
-			S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x20),
-			wdt_base + S3C2410_WTCON);
-
-	/* wait for reset to assert... */
-	mdelay(500);
-
-	pr_err("Watchdog reset failed to assert reset\n");
-
-	/* delay to allow the serial port to show the message */
-	mdelay(50);
-}
-
-#ifdef CONFIG_OF
-static const struct of_device_id s3c2410_wdt_match[] = {
-	{ .compatible = "samsung,s3c2410-wdt" },
-	{ .compatible = "samsung,s3c6410-wdt" },
-	{},
-};
-
-void __init samsung_wdt_reset_of_init(void)
-{
-	struct device_node *np;
-
-	np = of_find_matching_node(NULL, s3c2410_wdt_match);
-	if (!np) {
-		pr_err("%s: failed to find watchdog node\n", __func__);
-		return;
-	}
-
-	wdt_base = of_iomap(np, 0);
-	if (!wdt_base) {
-		pr_err("%s: failed to map watchdog registers\n", __func__);
-		return;
-	}
-
-	wdt_clock = of_clk_get(np, 0);
-}
-#endif
-
-void __init samsung_wdt_reset_init(void __iomem *base)
-{
-	wdt_base = base;
-	wdt_clock = clk_get(NULL, "watchdog");
-}
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index cd58f8495c45..d235b27cf372 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -80,7 +80,6 @@ config ARCH_EXYNOS
 	select EXYNOS_CHIPID
 	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
 	select EXYNOS_PMU
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select HAVE_S3C_RTC if RTC_CLASS
 	select PINCTRL
 	select PINCTRL_EXYNOS