Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging driver updates from Greg KH:
 "Here is the big staging driver pull request for 4.6-rc1.

  Lots of little things here, over 1600 patches or so.  Notable is all
  of the good Lustre work happening, those developers have finally woken
  up and are cleaning up their code greatly.  The Outreachy intern
  application process is also happening, which brought in another 400 or
  so patches.  Full details are in the very long shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
  staging: lustre: fix aligments in lnet selftest
  staging: lustre: report minimum of two buffers for LNet selftest load test
  staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
  staging: lustre: filter remaining extra spacing for lnet selftest
  staging: lustre: remove extra spacing when setting variable for lnet selftest
  staging: lustre: remove extra spacing of variable declartions for lnet selftest
  staging: lustre: fix spacing issues checkpatch reported in lnet selftest
  staging: lustre: remove returns in void function for lnet selftest
  staging: lustre: fix bogus lst errors for lnet selftest
  staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
  staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
  staging: android: ion: fix up file mode
  staging: ion: debugfs invalid gfp mask
  staging: rts5208: Replace pci_enable_device with pcim_enable_device
  Staging: ieee80211: Place constant on right side of the test.
  staging: speakup: Replace del_timer with del_timer_sync
  staging: lowmemorykiller: fix 2 checks that checkpatch complained
  staging: mt29f_spinand: Drop void pointer cast
  staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
  staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
  ...

22 files changed, 321 insertions, 582 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 0439c2aaf741..3c6624881375 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -496,8 +496,11 @@ Description:
 		1kohm_to_gnd: connected to ground via an 1kOhm resistor,
 		6kohm_to_gnd: connected to ground via a 6kOhm resistor,
 		20kohm_to_gnd: connected to ground via a 20kOhm resistor,
+		90kohm_to_gnd: connected to ground via a 90kOhm resistor,
 		100kohm_to_gnd: connected to ground via an 100kOhm resistor,
+		125kohm_to_gnd: connected to ground via an 125kOhm resistor,
 		500kohm_to_gnd: connected to ground via a 500kOhm resistor,
+		640kohm_to_gnd: connected to ground via a 640kOhm resistor,
 		three_state: left floating.
 		For a list of available output power down options read
 		outX_powerdown_mode_available. If Y is not present the
@@ -1491,3 +1494,10 @@ Description:
 		This ABI is especially applicable for humidity sensors
 		to heatup the device and get rid of any condensation
 		in some humidity environment
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_ph_raw
+KernelVersion:	4.5
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw (unscaled no offset etc.) pH reading of a substance as a negative
+		base-10 logarithm of hydrodium ions in a litre of water.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-health-afe440x b/Documentation/ABI/testing/sysfs-bus-iio-health-afe440x
new file mode 100644
index 000000000000..3740f253d406
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-health-afe440x
@@ -0,0 +1,54 @@
+What:		/sys/bus/iio/devices/iio:deviceX/tia_resistanceY
+		/sys/bus/iio/devices/iio:deviceX/tia_capacitanceY
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Get and set the resistance and the capacitance settings for the
+		Transimpedance Amplifier. Y is 1 for Rf1 and Cf1, Y is 2 for
+		Rf2 and Cf2 values.
+
+What:		/sys/bus/iio/devices/iio:deviceX/tia_separate_en
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Enable or disable separate settings for the TransImpedance
+		Amplifier above, when disabled both values are set by the
+		first channel.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_intensity_ledY_raw
+		/sys/bus/iio/devices/iio:deviceX/in_intensity_ledY_ambient_raw
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Get measured values from the ADC for these stages. Y is the
+		specific LED number. The values are expressed in 24-bit twos
+		complement.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_intensity_ledY-ledY_ambient_raw
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Get differential values from the ADC for these stages. Y is the
+		specific LED number. The values are expressed in 24-bit twos
+		complement for the specified LEDs.
+
+What:		/sys/bus/iio/devices/iio:deviceX/out_current_ledY_offset
+		/sys/bus/iio/devices/iio:deviceX/out_current_ledY_ambient_offset
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Get and set the offset cancellation DAC setting for these
+		stages. The values are expressed in 5-bit sign-magnitude.
+
+What:		/sys/bus/iio/devices/iio:deviceX/out_current_ledY_raw
+Date:		December 2015
+KernelVersion:
+Contact:	Andrew F. Davis <afd@ti.com>
+Description:
+		Get and set the LED current for the specified LED. Y is the
+		specific LED number.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-magnetometer-hmc5843 b/Documentation/ABI/testing/sysfs-bus-iio-magnetometer-hmc5843
new file mode 100644
index 000000000000..6275e9f56e6c
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-magnetometer-hmc5843
@@ -0,0 +1,15 @@
+What:           /sys/bus/iio/devices/iio:deviceX/meas_conf
+What:           /sys/bus/iio/devices/iio:deviceX/meas_conf_available
+KernelVersion:  4.5
+Contact:        linux-iio@vger.kernel.org
+Description:
+                Current configuration and available configurations
+		for the bias current.
+		normal		- Normal measurement configurations (default)
+		positivebias	- Positive bias configuration
+		negativebias	- Negative bias configuration
+		disabled	- Only available on HMC5983. Disables magnetic
+				  sensor and enables temperature sensor.
+		Note: The effect of this configuration may vary
+		according to the device. For exact documentation
+		check the device's datasheet.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-vf610 b/Documentation/ABI/testing/sysfs-bus-iio-vf610
index ecbc1f4af921..308a6756d3bf 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio-vf610
+++ b/Documentation/ABI/testing/sysfs-bus-iio-vf610
@@ -5,3 +5,12 @@ Description:
 		Specifies the hardware conversion mode used. The three
 		available modes are "normal", "high-speed" and "low-power",
 		where the last is the default mode.
+
+
+What:		/sys/bus/iio/devices/iio:deviceX/out_conversion_mode
+KernelVersion:	4.6
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Specifies the hardware conversion mode used within DAC.
+		The two available modes are "high-power" and "low-power",
+		where "low-power" mode is the default mode.
diff --git a/Documentation/devicetree/bindings/goldfish/audio.txt b/Documentation/devicetree/bindings/goldfish/audio.txt
new file mode 100644
index 000000000000..d043fda433ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/goldfish/audio.txt
@@ -0,0 +1,17 @@
+Android Goldfish Audio
+
+Android goldfish audio device generated by android emulator.
+
+Required properties:
+
+- compatible : should contain "google,goldfish-audio" to match emulator
+- reg        : <registers mapping>
+- interrupts : <interrupt mapping>
+
+Example:
+
+	goldfish_audio@9030000 {
+		compatible = "google,goldfish-audio";
+		reg = <0x9030000 0x100>;
+		interrupts = <0x4>;
+	};
diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
index 3c10e8581144..165937e1ac1c 100644
--- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
+++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
@@ -1,8 +1,10 @@
-Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer
+Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC
+triaxial accelerometer
 
 Required properties:
 
   - compatible: should contain one of
+    * "fsl,mma8451"
     * "fsl,mma8452"
     * "fsl,mma8453"
     * "fsl,mma8652"
diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt
new file mode 100644
index 000000000000..3223684a643b
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt
@@ -0,0 +1,28 @@
+* AT91 SAMA5D2 Analog to Digital Converter (ADC)
+
+Required properties:
+  - compatible: Should be "atmel,sama5d2-adc".
+  - reg: Should contain ADC registers location and length.
+  - interrupts: Should contain the IRQ line for the ADC.
+  - clocks: phandle to device clock.
+  - clock-names: Must be "adc_clk".
+  - vref-supply: Supply used as reference for conversions.
+  - vddana-supply: Supply for the adc device.
+  - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC.
+  - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC.
+  - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC.
+
+Example:
+
+adc: adc@fc030000 {
+	compatible = "atmel,sama5d2-adc";
+	reg = <0xfc030000 0x100>;
+	interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>;
+	clocks = <&adc_clk>;
+	clock-names = "adc_clk";
+	atmel,min-sample-rate-hz = <200000>;
+	atmel,max-sample-rate-hz = <20000000>;
+	atmel,startup-time-ms = <4>;
+	vddana-supply = <&vdd_3v3_lp_reg>;
+	vref-supply = <&vdd_3v3_lp_reg>;
+}
diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt
index dcae4ccfcc52..82bcce07255d 100644
--- a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt
+++ b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt
@@ -6,6 +6,7 @@ Required properties:
 	"microchip,mcp3422" or
 	"microchip,mcp3423" or
 	"microchip,mcp3424" or
+	"microchip,mcp3425" or
 	"microchip,mcp3426" or
 	"microchip,mcp3427" or
 	"microchip,mcp3428"
diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt
new file mode 100644
index 000000000000..d91130587d01
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt
@@ -0,0 +1,19 @@
+* Texas Instruments' ADC0831/ADC0832/ADC0832/ADC0838
+
+Required properties:
+ - compatible: Should be one of
+	* "ti,adc0831"
+	* "ti,adc0832"
+	* "ti,adc0834"
+	* "ti,adc0838"
+ - reg: spi chip select number for the device
+ - vref-supply: The regulator supply for ADC reference voltage
+ - spi-max-frequency: Max SPI frequency to use (< 400000)
+
+Example:
+adc@0 {
+	compatible = "ti,adc0832";
+	reg = <0>;
+	vref-supply = <&vdd_supply>;
+	spi-max-frequency = <200000>;
+};
diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
new file mode 100644
index 000000000000..cffa1907463a
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt
@@ -0,0 +1,22 @@
+* Atlas Scientific pH-SM OEM sensor
+
+http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf
+
+Required properties:
+
+  - compatible: must be "atlas,ph-sm"
+  - reg: the I2C address of the sensor
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+atlas@65 {
+	compatible = "atlas,ph-sm";
+	reg = <0x65>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 2>;
+};
diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt
new file mode 100644
index 000000000000..20c6c7ae9687
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt
@@ -0,0 +1,20 @@
+Freescale vf610 Digital to Analog Converter bindings
+
+The devicetree bindings are for the new DAC driver written for
+vf610 SoCs from Freescale.
+
+Required properties:
+- compatible: Should contain "fsl,vf610-dac"
+- reg: Offset and length of the register set for the device
+- interrupts: Should contain the interrupt for the device
+- clocks: The clock is needed by the DAC controller
+- clock-names: Must contain "dac" matching entry in the clocks property.
+
+Example:
+dac0: dac@400cc000 {
+	compatible = "fsl,vf610-dac";
+	reg = <0x400cc000 0x1000>;
+	interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "dac";
+	clocks = <&clks VF610_CLK_DAC0>;
+};
diff --git a/Documentation/devicetree/bindings/iio/health/afe4403.txt b/Documentation/devicetree/bindings/iio/health/afe4403.txt
new file mode 100644
index 000000000000..2fffd70336ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/health/afe4403.txt
@@ -0,0 +1,34 @@
+Texas Instruments AFE4403 Heart rate and Pulse Oximeter
+
+Required properties:
+ - compatible		: Should be "ti,afe4403".
+ - reg			: SPI chip select address of device.
+ - tx-supply		: Regulator supply to transmitting LEDs.
+ - interrupt-parent	: Phandle to he parent interrupt controller.
+ - interrupts		: The interrupt line the device ADC_RDY pin is
+			  connected to. For details refer to,
+			  ../../interrupt-controller/interrupts.txt.
+
+Optional properties:
+ - reset-gpios		: GPIO used to reset the device.
+			  For details refer to, ../../gpio/gpio.txt.
+
+For other required and optional properties of SPI slave nodes
+please refer to ../../spi/spi-bus.txt.
+
+Example:
+
+&spi0 {
+	heart_mon@0 {
+		compatible = "ti,afe4403";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		tx-supply = <&vbat>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_EDGE_RISING>;
+
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/iio/health/afe4404.txt b/Documentation/devicetree/bindings/iio/health/afe4404.txt
new file mode 100644
index 000000000000..de69f203edfa
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/health/afe4404.txt
@@ -0,0 +1,30 @@
+Texas Instruments AFE4404 Heart rate and Pulse Oximeter
+
+Required properties:
+ - compatible		: Should be "ti,afe4404".
+ - reg			: I2C address of the device.
+ - tx-supply		: Regulator supply to transmitting LEDs.
+ - interrupt-parent	: Phandle to he parent interrupt controller.
+ - interrupts		: The interrupt line the device ADC_RDY pin is
+			  connected to. For details refer to,
+			  ../interrupt-controller/interrupts.txt.
+
+Optional properties:
+ - reset-gpios		: GPIO used to reset the device.
+			  For details refer to, ../gpio/gpio.txt.
+
+Example:
+
+&i2c2 {
+	heart_mon@58 {
+		compatible = "ti,afe4404";
+		reg = <0x58>;
+
+		tx-supply = <&vbat>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_EDGE_RISING>;
+
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt
index f6fbac66ad06..295a9edfa4fd 100644
--- a/Documentation/devicetree/bindings/iio/health/max30100.txt
+++ b/Documentation/devicetree/bindings/iio/health/max30100.txt
@@ -11,11 +11,19 @@ Required properties:
   Refer to interrupt-controller/interrupts.txt for generic
   interrupt client node bindings.
 
+Optional properties:
+  - maxim,led-current-microamp: configuration for LED current in microamperes
+    while the engine is running. First indexed value is the configuration for
+    the RED LED, and second value is for the IR LED.
+
+    Refer to the datasheet for the allowed current values.
+
 Example:
 
 max30100@057 {
 	compatible = "maxim,max30100";
 	reg = <57>;
+	maxim,led-current-microamp = <24000 50000>;
 	interrupt-parent = <&gpio1>;
 	interrupts = <16 2>;
 };
diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt
new file mode 100644
index 000000000000..eac30d508849
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/opt3001.txt
@@ -0,0 +1,26 @@
+* Texas Instruments OPT3001 Ambient Light Sensor
+
+The driver supports interrupt-driven and interrupt-less operation, depending
+on whether an interrupt property has been populated into the DT. Note that
+the optional generation of IIO events on rising/falling light threshold changes
+requires the use of interrupts. Without interrupts, only the simple reading
+of the current light value is supported through the IIO API.
+
+http://www.ti.com/product/opt3001
+
+Required properties:
+  - compatible: should be "ti,opt3001"
+  - reg: the I2C address of the sensor
+
+Optional properties:
+  - interrupt-parent: should be the phandle for the interrupt controller
+  - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge)
+
+Example:
+
+opt3001@44 {
+	compatible = "ti,opt3001";
+	reg = <0x44>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index bd33a268fd1b..ee66defcdd8b 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -28,6 +28,7 @@ arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 artesyn	Artesyn Embedded Technologies Inc.
 asahi-kasei	Asahi Kasei Corp.
+atlas	Atlas Scientific LLC
 atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
diff --git a/Documentation/isdn/00-INDEX b/Documentation/isdn/00-INDEX
index e87e336f590e..2d1889b6c1fa 100644
--- a/Documentation/isdn/00-INDEX
+++ b/Documentation/isdn/00-INDEX
@@ -16,8 +16,6 @@ README.FAQ
 	- general info for FAQ.
 README.HiSax
 	- info on the HiSax driver which replaces the old teles.
-README.act2000
-	- info on driver for IBM ACT-2000 card.
 README.audio
 	- info for running audio over ISDN.
 README.avmb1
@@ -34,14 +32,8 @@ README.hfc-pci
 	- info on hfc-pci based cards.
 README.hysdn
         - info on driver for Hypercope active HYSDN cards
-README.icn
-	- info on the ICN-ISDN-card and its driver.
 README.mISDN
 	- info on the Modular ISDN subsystem (mISDN)
-README.pcbit
-	- info on the PCBIT-D ISDN adapter and driver.
-README.sc
-	- info on driver for Spellcaster cards.
 README.syncppp
 	- info on running Sync PPP over ISDN.
 README.x25
diff --git a/Documentation/isdn/README.act2000 b/Documentation/isdn/README.act2000
deleted file mode 100644
index ce7115e7f4ce..000000000000
--- a/Documentation/isdn/README.act2000
+++ /dev/null
@@ -1,104 +0,0 @@
-$Id: README.act2000,v 1.3 2000/08/06 09:22:51 armin Exp $
-
-This document describes the ACT2000 driver for the
-IBM Active 2000 ISDN card.
-
-There are 3 Types of this card available. A ISA-, MCA-, and PCMCIA-Bus
-Version. Currently, only the ISA-Bus version of the card is supported.
-However MCA and PCMCIA will follow soon.
-
-The ISA-Bus Version uses 8 IO-ports. The base port address has to be set
-manually using the DIP switches.
-
-Setting up the DIP switches for the IBM Active 2000 ISDN card:
-
-	 Note: S5 and S6 always set off!
-
-     S1  S2  S3  S4  Base-port
-     on  on  on  on  0x0200 (Factory default)
-     off on  on  on  0x0240 
-     on  off on  on  0x0280 
-     off off on  on  0x02c0 
-     on  on  off on  0x0300 
-     off on  off on  0x0340 
-     on  off off on  0x0380 
-     on  on  on  off 0xcfe0
-     off on  on  off 0xcfa0 
-     on  off on  off 0xcf60 
-     off off on  off 0xcf20 
-     on  on  off off 0xcee0 
-     off on  off off 0xcea0 
-     on  off off off 0xce60 
-     off off off off Card disabled 
-
-IRQ is configured by software. Possible values are:
-
-  3, 5, 7, 10, 11, 12, 15 and none (polled mode)
-
-
-The ACT2000 driver may either be built into the kernel or as a module.
-Initialization depends on how the driver is built:
-
-Driver built into the kernel:
-
-  The ACT2000 driver can be configured using the commandline-feature while
-  loading the kernel with LILO or LOADLIN. It accepts the following syntax:
-
-  act2000=b,p,i[,idstring]
-
-  where
-
-    b = Bus-Type      (1=ISA, 2=MCA, 3=PCMCIA)
-    p = portbase      (-1 means autoprobe)
-    i = Interrupt     (-1 means use next free IRQ, 0 means polled mode)
-
-  The idstring is an arbitrary string used for referencing the card
-  by the actctrl tool later.
-
-  Defaults used, when no parameters given at all:
-
-    1,-1,-1,""
-
-  which means: Autoprobe for an ISA card, use next free IRQ, let the
-  ISDN linklevel fill the IdString (usually "line0" for the first card).
- 
-  If you like to use more than one card, you can use the program
-  "actctrl" from the utility-package to configure additional cards.
-
-  Using the "actctrl"-utility, portbase and irq can also be changed
-  during runtime. The D-channel protocol is configured by the "dproto"
-  option of the "actctrl"-utility after loading the firmware into the
-  card's memory using the "actctrl"-utility.
-
-Driver built as module:
-
-  The module act2000.o can be configured during modprobe (insmod) by
-  appending its parameters to the modprobe resp. insmod commandline.
-  The following syntax is accepted:
-
-    act_bus=b act_port=p act_irq=i act_id=idstring
-
-  where b, p, i and idstring have the same meanings as the parameters
-  described for the builtin version above.
-
-  Using the "actctrl"-utility, the same features apply to the modularized
-  version as to the kernel-builtin one. (i.e. loading of firmware and
-  configuring the D-channel protocol)
-
-Loading the firmware into the card:
-
-  The firmware is supplied together with the isdn4k-utils package. It
-  can be found in the subdirectory act2000/firmware/
-
-  Assuming you have installed the utility-package correctly, the firmware
-  will be downloaded into the card using the following command:
-
-    actctrl -d idstring load /etc/isdn/bip11.btl
-
-  where idstring is the Name of the card, given during insmod-time or
-  (for kernel-builtin driver) on the kernel commandline. If only one
-  ISDN card is used, the -d isdstrin may be omitted.
-
-  For further documentation (adding more IBM Active 2000 cards), refer to
-  the manpage actctrl.8 which is included in the isdn4k-utils package.
-
diff --git a/Documentation/isdn/README.icn b/Documentation/isdn/README.icn
deleted file mode 100644
index 13f833d4e910..000000000000
--- a/Documentation/isdn/README.icn
+++ /dev/null
@@ -1,148 +0,0 @@
-$Id: README.icn,v 1.7 2000/08/06 09:22:51 armin Exp $
-
-You can get the ICN-ISDN-card from:
-
-Thinking Objects Software GmbH
-Versbacher Röthe 159
-97078 Würzburg
-Tel: +49 931 2877950
-Fax: +49 931 2877951
-
-email info@think.de
-WWW   http:/www.think.de
-
-
-The card communicates with the PC by two interfaces:
-  1. A range of 4 successive port-addresses, whose base address can be 
-     configured with the switches.
-  2. A memory window with 16KB-256KB size, which can be setup in 16k steps
-     over the whole range of 16MB. Isdn4linux only uses a 16k window.
-     The base address of the window can be configured when loading
-     the lowlevel-module (see README). If using more than one card,
-     all cards are mapped to the same window and activated as needed.
-
-Setting up the IO-address dipswitches for the ICN-ISDN-card:
-
-  Two types of cards exist, one with dip-switches and one with
-  hook-switches.
-
-  1. Setting for the card with hook-switches:
-
-     (0 = switch closed, 1 = switch open)
-
-     S3 S2 S1  Base-address
-      0  0  0  0x300
-      0  0  1  0x310
-      0  1  0  0x320 (Default for isdn4linux)
-      0  1  1  0x330
-      1  0  0  0x340
-      1  0  1  0x350
-      1  1  0  0x360
-      1  1  1  NOT ALLOWED!
-    
-  2. Setting for the card with dip-switches:
-
-     (0 = switch closed, 1 = switch open)
-
-     S1 S2 S3 S4  Base-Address
-      0  0  0  0  0x300
-      0  0  0  1  0x310
-      0  0  1  0  0x320 (Default for isdn4linux)
-      0  0  1  1  0x330
-      0  1  0  0  0x340
-      0  1  0  1  0x350
-      0  1  1  0  0x360
-      0  1  1  1  NOT ALLOWED!
-      1  0  0  0  0x308
-      1  0  0  1  0x318
-      1  0  1  0  0x328
-      1  0  1  1  0x338
-      1  1  0  0  0x348
-      1  1  0  1  0x358
-      1  1  1  0  0x368
-      1  1  1  1  NOT ALLOWED!
-
-The ICN driver may be built into the kernel or as a module. Initialization
-depends on how the driver is built:
-
-Driver built into the kernel:
-
-  The ICN driver can be configured using the commandline-feature while
-  loading the kernel with LILO or LOADLIN. It accepts the following syntax:
-
-  icn=p,m[,idstring1[,idstring2]]
-
-  where
-
-    p = portbase      (default: 0x320)
-    m = shared memory (default: 0xd0000)
-
-  When using the ICN double card (4B), you MUST define TWO idstrings.
-  idstring must start with a character! There is no way for the driver
-  to distinguish between a 2B and 4B type card. Therefore, by supplying
-  TWO idstrings, you tell the driver that you have a 4B installed.
-  
-  If you like to use more than one card, you can use the program
-  "icnctrl" from the utility-package to configure additional cards.
-  You need to configure shared memory only once, since the icn-driver
-  maps all cards into the same address-space.
-
-  Using the "icnctrl"-utility, portbase and shared memory can also be
-  changed during runtime.
-
-  The D-channel protocol is configured by loading different firmware
-  into the card's memory using the "icnctrl"-utility.
-
-
-Driver built as module:
-
-  The module icn.o can be configured during "insmod'ing" it by
-  appending its parameters to the insmod-commandline. The following
-  syntax is accepted:
-
-    portbase=p membase=m icn_id=idstring [icn_id2=idstring2]
-
-  where p, m, idstring1 and idstring2 have the same meanings as the
-  parameters described for the kernel-version above.
-      
-  When using the ICN double card (4B), you MUST define TWO idstrings.
-  idstring must start with a character! There is no way for the driver
-  to distinguish between a 2B and 4B type card. Therefore, by supplying
-  TWO idstrings, you tell the driver that you have a 4B installed.
-  
-  Using the "icnctrl"-utility, the same features apply to the modularized
-  version like to the kernel-builtin one.
-
-  The D-channel protocol is configured by loading different firmware
-  into the card's memory using the "icnctrl"-utility.
-
-Loading the firmware into the card:
-
-  The firmware is supplied together with the isdn4k-utils package. It
-  can be found in the subdirectory icnctrl/firmware/
-
-  There are 3 files:
-
-    loadpg.bin   - Image of the bootstrap loader.
-    pc_1t_ca.bin - Image of firmware for german 1TR6 protocol.
-    pc_eu_ca.bin - Image if firmware for EDSS1 (Euro-ISDN) protocol.
-
-  Assuming you have installed the utility-package correctly, the firmware
-  will be downloaded into the 2B-card using the following command:
-
-    icnctrl -d Idstring load /etc/isdn/loadpg.bin /etc/isdn/pc_XX_ca.bin
-
-  where XX is either "1t" or "eu", depending on the D-Channel protocol
-  used on your S0-bus and Idstring is the Name of the card, given during
-  insmod-time or (for kernel-builtin driver) on the kernel commandline.
-
-  To load a 4B-card, the same command is used, except a second firmware
-  file is appended to the commandline of icnctrl.
-
-  -> After downloading firmware, the two LEDs at the back cover of the card
-     (ICN-4B: 4 LEDs) must be blinking intermittently now. If a connection
-     is up, the corresponding led is lit continuously.
-
-  For further documentation (adding more ICN-cards), refer to the manpage
-  icnctrl.8 which is included in the isdn4k-utils package.
-
diff --git a/Documentation/isdn/README.pcbit b/Documentation/isdn/README.pcbit
deleted file mode 100644
index 5125002282e5..000000000000
--- a/Documentation/isdn/README.pcbit
+++ /dev/null
@@ -1,40 +0,0 @@
-------------------------------------------------------------------------------
- README file for the PCBIT-D Device Driver.
-------------------------------------------------------------------------------
-
-The PCBIT is a Euro ISDN adapter manufactured in Portugal by Octal and
-developed in cooperation with Portugal Telecom and Inesc.
-The driver interfaces with the standard kernel isdn facilities
-originally developed by Fritz Elfert in the isdn4linux project.
-
-The common versions of the pcbit board require a firmware that is 
-distributed (and copyrighted) by the manufacturer. To load this
-firmware you need "pcbitctl" available on the standard isdn4k-utils
-package or in the pcbit package available in:
-
-ftp://ftp.di.fc.ul.pt/pub/systems/Linux/isdn
-
-Known Limitations:
-
-- The board reset procedure is at the moment incorrect and will only
-allow you to load the firmware after a hard reset.
-
-- Only HDLC in B-channels is supported at the moment. There is no
-current support for X.25 in B or D channels nor LAPD in B
-channels. The main reason is that these two other protocol modes have,
-to my knowledge, very little use. If you want to see them implemented
-*do* send me a mail.
-
-- The driver often triggers errors in the board that I and the
-manufacturer believe to be caused by bugs in the firmware. The current
-version includes several procedures for error recovery that should
-allow normal operation. Plans for the future include cooperation with
-the manufacturer in order to solve this problem.
-
-Information/hints/help can be obtained in the linux isdn
-mailing list (isdn4linux@listserv.isdn4linux.de) or directly from me.
-
-regards,
-  Pedro.
-		
-<roque@di.fc.ul.pt>
diff --git a/Documentation/isdn/README.sc b/Documentation/isdn/README.sc
deleted file mode 100644
index 1153cd926059..000000000000
--- a/Documentation/isdn/README.sc
+++ /dev/null
@@ -1,281 +0,0 @@
-Welcome to Beta Release 2 of the combination ISDN driver for SpellCaster's
-ISA ISDN adapters. Please note this release 2 includes support for the
-DataCommute/BRI and TeleCommute/BRI adapters only and any other use is 
-guaranteed to fail. If you have a DataCommute/PRI installed in the test
-computer, we recommend removing it as it will be detected but will not
-be usable.  To see what we have done to Beta Release 2, see section 3.
-
-Speaking of guarantees, THIS IS BETA SOFTWARE and as such contains
-bugs and defects either known or unknown. Use this software at your own
-risk. There is NO SUPPORT for this software. Some help may be available
-through the web site or the mailing list but such support is totally at
-our own option and without warranty. If you choose to assume all and
-total risk by using this driver, we encourage you to join the beta
-mailing list.
-
-To join the Linux beta mailing list, send a message to:
-majordomo@spellcast.com with the words "subscribe linux-beta" as the only
-contents of the message. Do not include a signature. If you choose to
-remove yourself from this list at a later date, send another message to
-the same address with the words "unsubscribe linux-beta" as its only
-contents.
-
-TABLE OF CONTENTS
------------------
-	1. Introduction
-	 1.1 What is ISDN4Linux?
-	 1.2 What is different between this driver and previous drivers?
-	 1.3 How do I setup my system with the correct software to use
-	     this driver release?
-	
-	2. Basic Operations
-	 2.1 Unpacking and installing the driver
-	 2.2 Read the man pages!!!
-	 2.3 Installing the driver
-	 2.4 Removing the driver
-	 2.5 What to do if it doesn't load
-	 2.6 How to setup ISDN4Linux with the driver
-
-	3. Beta Change Summaries and Miscellaneous Notes
-
-1. Introduction
----------------
-
-The revision 2 Linux driver for SpellCaster ISA ISDN adapters is built
-upon ISDN4Linux available separately or as included in Linux 2.0 and later.
-The driver will support a maximum of 4 adapters in any one system of any
-type including DataCommute/BRI, DataCommute/PRI and TeleCommute/BRI for a
-maximum of 92 channels for host. The driver is supplied as a module in
-source form and needs to be complied before it can be used. It has been
-tested on Linux 2.0.20.
-
-1.1 What Is ISDN4Linux
-
-ISDN4Linux is a driver and set of tools used to access and use ISDN devices
-on a Linux platform in a common and standard way. It supports HDLC and PPP
-protocols and offers channel bundling and MLPPP support. To use ISDN4Linux
-you need to configure your kernel for ISDN support and get the ISDN4Linux
-tool kit from our web site.
-
-ISDN4Linux creates a channel pool from all of the available ISDN channels
-and therefore can function across adapters. When an ISDN4Linux compliant
-driver (such as ours) is loaded, all of the channels go into a pool and
-are used on a first-come first-served basis. In addition, individual
-channels can be specifically bound to particular interfaces.
-
-1.2 What is different between this driver and previous drivers?
-
-The revision 2 driver besides adopting the ISDN4Linux architecture has many
-subtle and not so subtle functional differences from previous releases. These
-include:
-	- More efficient shared memory management combined with a simpler
-	  configuration. All adapters now use only 16Kbytes of shared RAM
-	  versus between 16K and 64K. New methods for using the shared RAM
-	  allow us to utilize all of the available RAM on the adapter through
-	  only one 16K page.
-	- Better detection of available upper memory. The probing routines
-	  have been improved to better detect available shared RAM pages and
-	  used pages are now locked.
-	- Decreased loading time and a wider range of I/O ports probed.
-	  We have significantly reduced the amount of time it takes to load
-	  the driver and at the same time doubled the number of I/O ports
-	  probed increasing the likelihood of finding an adapter.
-	- We now support all ISA adapter models with a single driver instead
-	  of separate drivers for each model. The revision 2 driver supports
-	  the DataCommute/BRI, DataCommute/PRI and TeleCommute/BRI in any
-	  combination up to a maximum of four adapters per system.
-	- On board PPP protocol support has been removed in favour of the
-	  sync-PPP support used in ISDN4Linux. This means more control of
-	  the protocol parameters, faster negotiation time and a more
-	  familiar interface.
-
-1.3 How do I setup my system with the correct software to use
-    this driver release?
-
-Before you can compile, install and use the SpellCaster ISA ISDN driver, you
-must ensure that the following software is installed, configured and running:
-
-	- Linux kernel 2.0.20 or later with the required init and ps
-	  versions. Please see your distribution vendor for the correct
-	  utility packages. The latest kernel is available from
-	  ftp://sunsite.unc.edu/pub/Linux/kernel/v2.0/
-
-	- The latest modules package (modules-2.0.0.tar.gz) from
-	  ftp://sunsite.unc.edu/pub/Linux/kernel/modules-2.0.0.tar.gz
-
-	- The ISDN4Linux tools available from 
-	  ftp://ftp.franken.de/pub/isdn4linux/v2.0/isdn4k-utils-2.0.tar.gz
-	  This package may fail to compile for you so you can alternatively
-	  get a pre-compiled version from
-	  ftp://ftp.spellcast.com/pub/drivers/isdn4linux/isdn4k-bin-2.0.tar.gz
-
-
-2. Basic Operations
--------------------
-
-2.1 Unpacking and installing the driver
-
-	1. As root, create a directory in a convenient place. We suggest
-	   /usr/src/spellcaster.
-	
-	2. Unpack the archive with :
-		tar xzf sc-n.nn.tar.gz -C /usr/src/spellcaster
-	
-	3. Change directory to /usr/src/spellcaster
-
-	4. Read the README and RELNOTES files.
-
-	5. Run 'make' and if all goes well, run 'make install'.
-
-2.2 Read the man pages!!!
-
-Make sure you read the scctrl(8) and sc(4) manual pages before continuing
-any further. Type 'man 8 scctrl' and 'man 4 sc'.
-
-2.3 Installing the driver
-
-To install the driver, type '/sbin/insmod sc' as root. sc(4) details options
-you can specify but you shouldn't need to use any unless this doesn't work.
-
-Make sure the driver loaded and detected all of the adapters by typing
-'dmesg'.
-
-The driver can be configured so that it is loaded upon startup.  To do this, 
-edit the file "/etc/modules/'uname -f'/'uname -v'" and insert the driver name
-"sc" into this file.
-
-2.4 Removing the driver
-
-To remove the driver, delete any interfaces that may exist (see isdnctrl(8)
-for more on this) and then type '/sbin/rmmod sc'.
-
-2.5 What to do if it doesn't load
-
-If, when you try to install the driver, you get a message mentioning
-'register_isdn' then you do not have the ISDN4Linux system installed. Please
-make sure that ISDN support is configured in the kernel.
-
-If you get a message that says 'initialization of sc failed', then the
-driver failed to detect an adapter or failed to find resources needed such
-as a free IRQ line or shared memory segment. If you are sure there are free
-resources available, use the insmod options detailed in sc(4) to override
-the probing function.  
-
-Upon testing, the following problem was noted, the driver would load without
-problems, but the board would not respond beyond that point.  When a check was 
-done with 'cat /proc/interrupts' the interrupt count for sc was 0.  In the event 
-of this problem, change the BIOS settings so that the interrupts in question are
-reserved for ISA use only.   
-
-
-2.6 How to setup ISDN4Linux with the driver
-
-There are three main configurations which you can use with the driver:
-
-A)	Basic HDLC connection
-B)	PPP connection
-C)	MLPPP connection
-
-It should be mentioned here that you may also use a tty connection if you
-desire. The Documentation directory of the isdn4linux subsystem offers good
-documentation on this feature.
-
-A) 10 steps to the establishment of a basic HDLC connection
------------------------------------------------------------
-
-- please open the isdn-hdlc file in the examples directory and follow along...
-	
-	This file is a script used to configure a BRI ISDN TA to establish a 
-	basic HDLC connection between its two channels.  Two network 
-	interfaces are created and two routes added between the channels.
-
-	i)   using the isdnctrl utility, add an interface with "addif" and 
-	     name it "isdn0"
-	ii)  add the outgoing and inbound telephone numbers
-	iii) set the Layer 2 protocol to hdlc
-	iv)  set the eaz of the interface to be the phone number of that 
-	     specific channel
-	v)   to turn the callback features off, set the callback to "off" and
-	     the callback delay (cbdelay) to 0.
-	vi)  the hangup timeout can be set to a specified number of seconds
-	vii) the hangup upon incoming call can be set on or off 
-	viii) use the ifconfig command to bring up the network interface with 
-	      a specific IP address and point to point address
-	ix)  add a route to the IP address through the isdn0 interface
-	x)   a ping should result in the establishment of the connection
-
-	
-B) Establishment of a PPP connection
-------------------------------------
-
-- please open the isdn-ppp file in the examples directory and follow along...
-	
-	This file is a script used to configure a BRI ISDN TA to establish a 
-	PPP connection 	between the two channels.  The file is almost 
-	identical to the HDLC connection example except that the packet 
-	encapsulation type has to be set.
-	
-	use the same procedure as in the HDLC connection from steps i) to 
-	iii) then, after the Layer 2 protocol is set, set the encapsulation 
-	"encap" to syncppp. With this done, the rest of the steps, iv) to x) 
-	can be followed from above.
-
-	Then, the ipppd (ippp daemon) must be setup:
-	
-	xi)   use the ipppd function found in /sbin/ipppd to set the following:
-	xii)  take out (minus) VJ compression and bsd compression
-	xiii) set the mru size to 2000
-	xiv)  link the two /dev interfaces to the daemon
-
-NOTE:  A "*" in the inbound telephone number specifies that a call can be 
-accepted on any number.
-
-C) Establishment of a MLPPP connection
---------------------------------------
-
-- please open the isdn-mppp file in the examples directory and follow along...
-	
-	This file is a script used to configure a BRI ISDN TA to accept a 
-	Multi Link PPP connection. 
-	
-	i)   using the isdnctrl utility, add an interface with "addif" and 
-	     name it "ippp0"
-	ii)  add the inbound telephone number
-	iii) set the Layer 2 protocol to hdlc and the Layer 3 protocol to 
-	     trans (transparent)
-	iv)  set the packet encapsulation to syncppp
-	v)   set the eaz of the interface to be the phone number of that 
-	     specific channel
-	vi)  to turn the callback features off, set the callback to "off" and
-	     the callback delay (cbdelay) to 0.
-	vi)  the hangup timeout can be set to a specified number of seconds
-	vii) the hangup upon incoming call can be set on or off 
-	viii) add a slave interface and name it "ippp32" for example
-	ix)  set the similar parameters for the ippp32 interface
-	x)   use the ifconfig command to bring-up the ippp0 interface with a 
-	     specific IP address and point to point address
-	xi)  add a route to the IP address through the ippp0 interface
-	xii) use the ipppd function found in /sbin/ipppd to set the following:
-	xiii) take out (minus) bsd compression
-	xiv) set the mru size to 2000
-	xv)  add (+) the multi-link function "+mp"
-	xvi)  link the two /dev interfaces to the daemon
-
-NOTE:  To use the MLPPP connection to dial OUT to a MLPPP connection, change 
-the inbound telephone numbers to the outgoing telephone numbers of the MLPPP 
-host.
-
-	
-3. Beta Change Summaries and Miscellaneous Notes
-------------------------------------------------
-When using the "scctrl" utility to upload firmware revisions on the board,
-please note that the byte count displayed at the end of the operation may be
-different from the total number of bytes in the "dcbfwn.nn.sr" file. Please
-disregard the displayed byte count.
-
-It was noted that in Beta Release 1, the module would fail to load and result
-in a segmentation fault when 'insmod'ed. This problem was created when one of
-the isdn4linux parameters, (isdn_ctrl, data field) was filled in. In some
-cases, this data field was NULL, and was left unchecked, so when it was
-referenced... segv. The bug has been fixed around line 63-68 of event.c.
-
diff --git a/Documentation/misc-devices/lcd-panel-cgram.txt b/Documentation/misc-devices/lcd-panel-cgram.txt
new file mode 100644
index 000000000000..7f82c905763d
--- /dev/null
+++ b/Documentation/misc-devices/lcd-panel-cgram.txt
@@ -0,0 +1,24 @@
+Some LCDs allow you to define up to 8 characters, mapped to ASCII
+characters 0 to 7. The escape code to define a new character is
+'\e[LG' followed by one digit from 0 to 7, representing the character
+number, and up to 8 couples of hex digits terminated by a semi-colon
+(';'). Each couple of digits represents a line, with 1-bits for each
+illuminated pixel with LSB on the right. Lines are numbered from the
+top of the character to the bottom. On a 5x7 matrix, only the 5 lower
+bits of the 7 first bytes are used for each character. If the string
+is incomplete, only complete lines will be redefined. Here are some
+examples :
+
+  printf "\e[LG0010101050D1F0C04;"  => 0 = [enter]
+  printf "\e[LG1040E1F0000000000;"  => 1 = [up]
+  printf "\e[LG2000000001F0E0400;"  => 2 = [down]
+  printf "\e[LG3040E1F001F0E0400;"  => 3 = [up-down]
+  printf "\e[LG40002060E1E0E0602;"  => 4 = [left]
+  printf "\e[LG500080C0E0F0E0C08;"  => 5 = [right]
+  printf "\e[LG60016051516141400;"  => 6 = "IP"
+
+  printf "\e[LG00103071F1F070301;"  => big speaker
+  printf "\e[LG00002061E1E060200;"  => small speaker
+
+Willy
+