Merge branch 'regulator-4.21' into regulator-next

6 files changed, 278 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 188f0373d441..2af4ff95d6bc 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -32,6 +32,15 @@ Required properties:
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
+Supported common regulator properties, see ../regulator/regulator.txt for
+more information:
+- regulator-ramp-delay: sets the ramp up delay in uV/us
+			AXP20x/DCDC2: 1600, 800
+			AXP20x/LDO3:  1600, 800
+- regulator-soft-start:	enable the output at the lowest possible voltage and
+			only then set the desired voltage
+			AXP20x/LDO3: software-based implementation
+
 Optional properties:
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
index ac955dea00d1..4017527619ab 100644
--- a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
@@ -15,11 +15,17 @@ Optional input supply properties:
   - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
 
 Any standard regulator properties can be used to configure the single regulator.
+regulator-initial-mode, regulator-allowed-modes and regulator-mode could be
+specified using mode values from dt-bindings/regulator/active-semi,8945a-regulator.h
+file.
 
 The valid names for regulators are:
 	REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4.
 
 Example:
+
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
+
 	pmic@5b {
 		compatible = "active-semi,act8945a";
 		reg = <0x5b>;
@@ -32,6 +38,18 @@ Example:
 				regulator-min-microvolt = <1350000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt=<1400000>;
+					regulator-suspend-max-microvolt=<1400000>;
+					regulator-changeable-in-suspend;
+					regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				};
 			};
 
 			vdd_1v2_reg: REG_DCDC2 {
@@ -39,6 +57,14 @@ Example:
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_reg: REG_DCDC3 {
@@ -53,6 +79,14 @@ Example:
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <2500000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_lp_reg: REG_LDO2 {
diff --git a/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
new file mode 100644
index 000000000000..91974e6ee251
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
@@ -0,0 +1,82 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the regulator portion
+of the driver.
+
+Also see these documents for generic binding information:
+  [1] Regulator: ../regulator/regulator.txt
+
+This binding must be part of the Lochnagar MFD binding:
+  [2] ../mfd/cirrus,lochnagar.txt
+
+Optional sub-nodes:
+
+  - VDDCORE : Initialisation data for the VDDCORE regulator, which
+    supplies the CODECs digital core if it has no build regulator for that
+    purpose.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-vddcore"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MICVDD : Initialisation data for the MICVDD regulator, which
+    supplies the CODECs MICVDD.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-micvdd"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-mic1vdd", "cirrus,lochnagar2-mic2vdd"
+      Optional Properties:
+      - cirrus,micbias-input : A property selecting which of the CODEC
+        minicard micbias outputs should be used, valid values are 1 - 4.
+      - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
+        MICxVDD outputs, supplying the digital microphones, normally
+        supplied from the attached CODEC.
+
+  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
+    CODECs analog and 1.8V digital supplies.
+      Required Properties:
+      - compatible : Should be set to "regulator-fixed"
+      - regulator-min-microvolt : Should be set to 1.8V
+      - regulator-max-microvolt : Should be set to 1.8V
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply : Should be set to same supply as SYSVDD
+
+Example:
+
+lochnagar {
+	lochnagar-micvdd: MICVDD {
+		compatible = "cirrus,lochnagar2-micvdd";
+
+		SYSVDD-supply = <&wallvdd>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lochnagar-vdd1v8: VDD1V8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDD1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+
+		vin-supply = <&wallvdd>;
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt b/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
new file mode 100644
index 000000000000..b8f843fa6092
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
@@ -0,0 +1,143 @@
+MCP16502 PMIC
+
+Required properties:
+- compatible: "microchip,mcp16502"
+- reg: I2C slave address
+- lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
+	     suspend-to-ram, keeping the PMIC into HIBERNATE mode.
+- regulators: A node that houses a sub-node for each regulator within
+              the device. Each sub-node is identified using the node's
+              name. The content of each sub-node is defined by the
+              standard binding for regulators; see regulator.txt.
+
+Regualtors of MCP16502 PMIC:
+1) VDD_IO	- Buck (1.2 - 3.7 V)
+2) VDD_DDR	- Buck (0.6 - 1.85 V)
+3) VDD_CORE	- Buck (0.6 - 1.85 V)
+4) VDD_OTHER	- BUCK (0.6 - 1.85 V)
+5) LDO1		- LDO  (1.2 - 3.7 V)
+6) LDO2		- LDO  (1.2 - 3.7 V)
+
+Regulator modes:
+2 - FPWM: higher precision, higher consumption
+4 - AutoPFM: lower precision, lower consumption
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+mcp16502@5b {
+	compatible = "microchip,mcp16502";
+	reg = <0x5b>;
+	status = "okay";
+	lpm-gpios = <&pioBU 7 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		VDD_IO {
+			regulator-name = "VDD_IO";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_DDR {
+			regulator-name = "VDD_DDR";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_CORE {
+			regulator-name = "VDD_CORE";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_OTHER {
+			regulator-name = "VDD_OTHER";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+	};
+};
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index a7cd36877bfe..0a3f087d5844 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -33,13 +33,16 @@ Optional properties:
   decreases of any level. This is useful for regulators with exponential
   voltage changes.
 - regulator-soft-start: Enable soft start so that voltage ramps slowly
+- regulator-state-standby sub-root node for Standby mode
+  : equivalent with standby Linux sleep state, which provides energy savings
+  with a relatively quick transition back time.
 - regulator-state-mem sub-root node for Suspend-to-RAM mode
   : suspend to memory, the device goes to sleep, but all data stored in memory,
   only some external interrupt can wake the device.
 - regulator-state-disk sub-root node for Suspend-to-DISK mode
   : suspend to disk, this state operates similarly to Suspend-to-RAM,
   but includes a final step of writing memory contents to disk.
-- regulator-state-[mem/disk] node has following common properties:
+- regulator-state-[mem/disk/standby] node has following common properties:
 	- regulator-on-in-suspend: regulator should be on in suspend state.
 	- regulator-off-in-suspend: regulator should be off in suspend state.
 	- regulator-suspend-min-microvolt: minimum voltage may be set in
@@ -76,8 +79,11 @@ Optional properties:
 - regulator-coupled-with: Regulators with which the regulator
   is coupled. The linkage is 2-way - all coupled regulators should be linked
   with each other. A regulator should not be coupled with its supplier.
-- regulator-coupled-max-spread: Max spread between voltages of coupled regulators
-  in microvolts.
+- regulator-coupled-max-spread: Array of maximum spread between voltages of
+  coupled regulators in microvolts, each value in the array relates to the
+  corresponding couple specified by the regulator-coupled-with property.
+- regulator-max-step-microvolt: Maximum difference between current and target
+  voltages that can be changed safely in a single step.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple
diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt
index 43681ca0837f..fc4cc24dfb97 100644
--- a/Documentation/driver-model/devres.txt
+++ b/Documentation/driver-model/devres.txt
@@ -254,6 +254,7 @@ GPIO
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
   devm_gpiod_put()
+  devm_gpiod_unhinge()
   devm_gpiochip_add_data()
   devm_gpiochip_remove()
   devm_gpio_request()