Merge tag 'spi-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "For the most part this is a quiet release for SPI, though there's
  several of the more widely used drivers that have had some fairly
  substantial development done on them, mainly improving performance and
  adding support for some more obscure use cases.

  Summary:

   - Support for configuring a minimum time for chip select to be
     deasserted between transfers from Martin Sperl.

   - A rework of the ACPI device instantiation code from Ard Biesheuvel.

   - Fairly substantial development on the AT91 USART, BCM2835 and
     Tegra114 drivers.

   - New driver for Socionext SynQuacer"

* tag 'spi-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (58 commits)
  spi: pxa2xx: Add support for Intel Elkhart Lake
  spi: atmel-quadspi: fix resume call
  spi: atmel-quadspi: void return type for atmel_qspi_init()
  spi: pxa2xx: Set minimum transfer speed
  spi: stm32-qspi: remove signal sensitive on completion
  dt-bindings: spi: stm32-qspi: add dma properties
  spi: uniphier: fix zero-length transfer
  spi: uniphier: fix timeout error
  spi/acpi: avoid spurious matches during slave enumeration
  spi: spi-stm32-qspi: Remove CR_FTHRES_MASK usage
  spi: fix ctrl->num_chipselect constraint
  spi: spi-synquacer: Fixed build on architectures missing readsl/writesl series
  spi/acpi: fix incorrect ACPI parent check
  spi: don't open code list_for_each_entry_safe_reverse()
  spi: No need to assign dummy value in spi_unregister_controller()
  spi: Add a prototype for exported spi_set_cs_timing()
  spi/acpi: enumerate all SPI slaves in the namespace
  spi: qup: fix PIO/DMA transfers.
  spi: Use struct_size() helper
  spi: mediatek: add SPI_LSB_FIRST support
  ...

13 files changed, 637 insertions, 297 deletions

diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7f0cd72f47d2..699fd3c9ace8 100644
--- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -17,17 +17,24 @@ Required properties for USART in SPI mode:
 - cs-gpios: chipselects (internal cs not supported)
 - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
 
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
 Optional properties in serial mode:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
   It will use specified PIO instead of the peripheral function pin for the USART feature.
   If unsure, don't specify this property.
-- add dma bindings for dma transfer:
-	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
-		memory peripheral interface and USART DMA channel ID, FIFO configuration.
-		Refer to dma.txt and atmel-dma.txt for details.
-	- dma-names: "rx" for RX channel, "tx" for TX channel.
 - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
   capable USARTs.
 - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
@@ -81,5 +88,8 @@ Example:
 		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 		clocks = <&usart0_clk>;
 		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
 		cs-gpios = <&pioB 3 0>;
 	};
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml
new file mode 100644
index 000000000000..c374fd4923a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/allwinner,sun4i-a10-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 SPI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "spi-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    const: allwinner,sun4i-a10-spi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: ahb
+      - const: mod
+
+  dmas:
+    items:
+      - description: RX DMA Channel
+      - description: TX DMA Channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+  num-cs: true
+
+patternProperties:
+  "^.*@[0-9a-f]+":
+    properties:
+      reg:
+        items:
+          minimum: 0
+          maximum: 4
+
+      spi-rx-bus-width:
+        const: 1
+
+      spi-tx-bus-width:
+        const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    spi1: spi@1c06000 {
+        compatible = "allwinner,sun4i-a10-spi";
+        reg = <0x01c06000 0x1000>;
+        interrupts = <11>;
+        clocks = <&ahb_gates 21>, <&spi1_clk>;
+        clock-names = "ahb", "mod";
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
new file mode 100644
index 000000000000..bda7a5befd8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -0,0 +1,106 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/allwinner,sun6i-a31-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 SPI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "spi-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    enum:
+      - allwinner,sun6i-a31-spi
+      - allwinner,sun8i-h3-spi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: ahb
+      - const: mod
+
+  resets:
+    maxItems: 1
+
+  dmas:
+    items:
+      - description: RX DMA Channel
+      - description: TX DMA Channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+  num-cs: true
+
+patternProperties:
+  "^.*@[0-9a-f]+":
+    properties:
+      reg:
+        items:
+          minimum: 0
+          maximum: 4
+
+      spi-rx-bus-width:
+        const: 1
+
+      spi-tx-bus-width:
+        const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    spi1: spi@1c69000 {
+        compatible = "allwinner,sun6i-a31-spi";
+        reg = <0x01c69000 0x1000>;
+        interrupts = <0 66 4>;
+        clocks = <&ahb1_gates 21>, <&spi1_clk>;
+        clock-names = "ahb", "mod";
+        resets = <&ahb1_rst 21>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+  - |
+    spi0: spi@1c68000 {
+        compatible = "allwinner,sun8i-h3-spi";
+        reg = <0x01c68000 0x1000>;
+        interrupts = <0 65 4>;
+        clocks = <&ccu 30>, <&ccu 82>;
+        clock-names = "ahb", "mod";
+        dmas = <&dma 23>, <&dma 23>;
+        dma-names = "rx", "tx";
+        resets = <&ccu 15>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index 1f6e86f787ef..e07783505498 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -1,111 +1 @@
-SPI (Serial Peripheral Interface) busses
-
-SPI busses can be described with a node for the SPI controller device
-and a set of child nodes for each SPI slave on the bus.  The system's SPI
-controller may be described for use in SPI master mode or in SPI slave mode,
-but not for both at the same time.
-
-The SPI controller node requires the following properties:
-- compatible      - Name of SPI bus controller following generic names
-		    recommended practice.
-
-In master mode, the SPI controller node requires the following additional
-properties:
-- #address-cells  - number of cells required to define a chip select
-		address on the SPI bus.
-- #size-cells     - should be zero.
-
-In slave mode, the SPI controller node requires one additional property:
-- spi-slave       - Empty property.
-
-No other properties are required in the SPI bus node.  It is assumed
-that a driver for an SPI bus device will understand that it is an SPI bus.
-However, the binding does not attempt to define the specific method for
-assigning chip select numbers.  Since SPI chip select configuration is
-flexible and non-standardized, it is left out of this binding with the
-assumption that board specific platform code will be used to manage
-chip selects.  Individual drivers can define additional properties to
-support describing the chip select layout.
-
-Optional properties (master mode only):
-- cs-gpios	  - gpios chip select.
-- num-cs	  - total number of chipselects.
-
-If cs-gpios is used the number of chip selects will be increased automatically
-with max(cs-gpios > hw cs).
-
-So if for example the controller has 2 CS lines, and the cs-gpios
-property looks like this:
-
-cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
-
-Then it should be configured so that num_chipselect = 4 with the
-following mapping:
-
-cs0 : &gpio1 0 0
-cs1 : native
-cs2 : &gpio1 1 0
-cs3 : &gpio1 2 0
-
-
-SPI slave nodes must be children of the SPI controller node.
-
-In master mode, one or more slave nodes (up to the number of chip selects) can
-be present.  Required properties are:
-- compatible      - Name of SPI device following generic names recommended
-		    practice.
-- reg             - Chip select address of device.
-- spi-max-frequency - Maximum SPI clocking speed of device in Hz.
-
-In slave mode, the (single) slave node is optional.
-If present, it must be called "slave".  Required properties are:
-- compatible      - Name of SPI device following generic names recommended
-		    practice.
-
-All slave nodes can contain the following optional properties:
-- spi-cpol        - Empty property indicating device requires inverse clock
-		    polarity (CPOL) mode.
-- spi-cpha        - Empty property indicating device requires shifted clock
-		    phase (CPHA) mode.
-- spi-cs-high     - Empty property indicating device requires chip select
-		    active high.
-- spi-3wire       - Empty property indicating device requires 3-wire mode.
-- spi-lsb-first   - Empty property indicating device requires LSB first mode.
-- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI.
-		    Defaults to 1 if not present.
-- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO.
-		    Defaults to 1 if not present.
-- spi-rx-delay-us - Microsecond delay after a read transfer.
-- spi-tx-delay-us - Microsecond delay after a write transfer.
-
-Some SPI controllers and devices support Dual and Quad SPI transfer mode.
-It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4
-wires (QUAD).
-Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is
-only 1 (SINGLE), 2 (DUAL) and 4 (QUAD).
-Dual/Quad mode is not allowed when 3-wire mode is used.
-
-If a gpio chipselect is used for the SPI slave the gpio number will be passed
-via the SPI master node cs-gpios property.
-
-SPI example for an MPC5200 SPI bus:
-	spi@f00 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-		reg = <0xf00 0x20>;
-		interrupts = <2 13 0 2 14 0>;
-		interrupt-parent = <&mpc5200_pic>;
-
-		ethernet-switch@0 {
-			compatible = "micrel,ks8995m";
-			spi-max-frequency = <1000000>;
-			reg = <0>;
-		};
-
-		codec@1 {
-			compatible = "ti,tlv320aic26";
-			spi-max-frequency = <100000>;
-			reg = <1>;
-		};
-	};
+This file has moved to spi-controller.yaml.
diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml
new file mode 100644
index 000000000000..876c0623f322
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI Controller Generic Binding
+
+maintainers:
+  - Mark Brown <broonie@kernel.org>
+
+description: |
+  SPI busses can be described with a node for the SPI controller device
+  and a set of child nodes for each SPI slave on the bus. The system SPI
+  controller may be described for use in SPI master mode or in SPI slave mode,
+  but not for both at the same time.
+
+properties:
+  $nodename:
+    pattern: "^spi(@.*|-[0-9a-f])*$"
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  cs-gpios:
+    description: |
+      GPIOs used as chip selects.
+      If that property is used, the number of chip selects will be
+      increased automatically with max(cs-gpios, hardware chip selects).
+
+      So if, for example, the controller has 2 CS lines, and the
+      cs-gpios looks like this
+        cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;
+
+      Then it should be configured so that num_chipselect = 4, with
+      the following mapping
+        cs0 : &gpio1 0 0
+        cs1 : native
+        cs2 : &gpio1 1 0
+        cs3 : &gpio1 2 0
+
+  num-cs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Total number of chip selects.
+
+  spi-slave:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The SPI controller acts as a slave, instead of a master.
+
+patternProperties:
+  "^slave$":
+    type: object
+
+    properties:
+      compatible:
+        description:
+          Compatible of the SPI device.
+
+    required:
+      - compatible
+
+  "^.*@[0-9a-f]+$":
+    type: object
+
+    properties:
+      compatible:
+        description:
+          Compatible of the SPI device.
+
+      reg:
+        maxItems: 1
+        minimum: 0
+        maximum: 256
+        description:
+          Chip select used by the device.
+
+      spi-3wire:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires 3-wire mode.
+
+      spi-cpha:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires shifted clock phase (CPHA) mode.
+
+      spi-cpol:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires inverse clock polarity (CPOL) mode.
+
+      spi-cs-high:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires the chip select active high.
+
+      spi-lsb-first:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The device requires the LSB first mode.
+
+      spi-max-frequency:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Maximum SPI clocking speed of the device in Hz.
+
+      spi-rx-bus-width:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [ 1, 2, 4 ]
+          - default: 1
+        description:
+          Bus width to the SPI bus used for MISO.
+
+      spi-rx-delay-us:
+        description:
+          Delay, in microseconds, after a read transfer.
+
+      spi-tx-bus-width:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [ 1, 2, 4 ]
+          - default: 1
+        description:
+          Bus width to the SPI bus used for MOSI.
+
+      spi-tx-delay-us:
+        description:
+          Delay, in microseconds, after a write transfer.
+
+    required:
+      - compatible
+      - reg
+
+examples:
+  - |
+    spi@f00 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+        reg = <0xf00 0x20>;
+        interrupts = <2 13 0 2 14 0>;
+        interrupt-parent = <&mpc5200_pic>;
+
+        ethernet-switch@0 {
+            compatible = "micrel,ks8995m";
+            spi-max-frequency = <1000000>;
+            reg = <0>;
+        };
+
+        codec@1 {
+            compatible = "ti,tlv320aic26";
+            spi-max-frequency = <100000>;
+            reg = <1>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt
deleted file mode 100644
index 52db562f17a4..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-gpio.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-SPI-GPIO devicetree bindings
-
-This represents a group of 3-n GPIO lines used for bit-banged SPI on dedicated
-GPIO lines.
-
-Required properties:
-
- - compatible: should be set to "spi-gpio"
- - #address-cells: should be set to <0x1>
- - ranges
- - sck-gpios: GPIO spec for the SCK line to use
- - miso-gpios: GPIO spec for the MISO line to use
- - mosi-gpios: GPIO spec for the MOSI line to use
- - cs-gpios: GPIOs to use for chipselect lines.
-             Not needed if num-chipselects = <0>.
- - num-chipselects: Number of chipselect lines. Should be <0> if a single device
-                    with no chip select is connected.
-
-Deprecated bindings:
-
-These legacy GPIO line bindings can alternatively be used to define the
-GPIO lines used, they should not be used in new device trees.
-
- - gpio-sck: GPIO spec for the SCK line to use
- - gpio-miso: GPIO spec for the MISO line to use
- - gpio-mosi: GPIO spec for the MOSI line to use
-
-Example:
-
-	spi {
-		compatible = "spi-gpio";
-		#address-cells = <0x1>;
-		ranges;
-
-		sck-gpios = <&gpio 95 0>;
-		miso-gpios = <&gpio 98 0>;
-		mosi-gpios = <&gpio 97 0>;
-		cs-gpios = <&gpio 125 0>;
-		num-chipselects = <1>;
-
-		/* clients */
-	};
-
diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.yaml b/Documentation/devicetree/bindings/spi/spi-gpio.yaml
new file mode 100644
index 000000000000..55c4f1705f07
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-gpio.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI-GPIO devicetree bindings
+
+maintainers:
+  - Rob Herring <robh@kernel.org>
+
+description:
+  This represents a group of 3-n GPIO lines used for bit-banged SPI on
+  dedicated GPIO lines.
+
+allOf:
+  - $ref: "/schemas/spi/spi-controller.yaml#"
+
+properties:
+  compatible:
+    const: spi-gpio
+
+  sck-gpios:
+    description: GPIO spec for the SCK line to use
+    maxItems: 1
+
+  miso-gpios:
+    description: GPIO spec for the MISO line to use
+    maxItems: 1
+
+  mosi-gpios:
+    description: GPIO spec for the MOSI line to use
+    maxItems: 1
+
+  cs-gpios:
+    description: GPIOs to use for chipselect lines.
+      Not needed if num-chipselects = <0>.
+    minItems: 1
+    maxItems: 1024
+
+  num-chipselects:
+    description: Number of chipselect lines. Should be <0> if a single device
+      with no chip select is connected.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  # Deprecated properties
+  gpio-sck: false
+  gpio-miso: false
+  gpio-mosi: false
+
+required:
+  - compatible
+  - num-chipselects
+  - sck-gpios
+
+examples:
+  - |
+    spi {
+      compatible = "spi-gpio";
+      #address-cells = <0x1>;
+      #size-cells = <0x0>;
+
+      sck-gpios = <&gpio 95 0>;
+      miso-gpios = <&gpio 98 0>;
+      mosi-gpios = <&gpio 97 0>;
+      cs-gpios = <&gpio 125 0>;
+      num-chipselects = <1>;
+
+      /* clients */
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-pl022.yaml b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
new file mode 100644
index 000000000000..dfb697c69341
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
@@ -0,0 +1,165 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-pl022.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM PL022 SPI controller
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+  properties:
+    compatible:
+      contains:
+        const: arm,pl022
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - const: arm,pl022
+      - const: arm,primecell
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - enum:
+          - SSPCLK
+          - sspclk
+      - const: apb_pclk
+
+  pl022,autosuspend-delay:
+    description: delay in ms following transfer completion before the
+      runtime power management system suspends the device. A setting of 0
+      indicates no delay and the device will be suspended immediately.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  pl022,rt:
+    description: indicates the controller should run the message pump with realtime
+               priority to minimise the transfer latency on the bus (boolean)
+    type: boolean
+
+  dmas:
+    description:
+      Two or more DMA channel specifiers following the convention outlined
+      in bindings/dma/dma.txt
+    minItems: 2
+    maxItems: 32
+
+  dma-names:
+    description:
+      There must be at least one channel named "tx" for transmit and named "rx"
+      for receive.
+    minItems: 2
+    maxItems: 32
+    additionalItems: true
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
+    type: object
+    # SPI slave nodes must be children of the SPI master node and can
+    # contain the following properties.
+    properties:
+      pl022,interface:
+        description: SPI interface type
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # SPI
+              - 1  # Texas Instruments Synchronous Serial Frame Format
+              - 2  # Microwire (Half Duplex)
+
+      pl022,com-mode:
+        description: Specifies the transfer mode
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # interrupt mode
+              - 1  # polling mode
+              - 2  # DMA mode
+            default: 1
+
+      pl022,rx-level-trig:
+        description: Rx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,tx-level-trig:
+        description: Tx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,ctrl-len:
+        description: Microwire interface - Control length
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0x03
+            maximum: 0x1f
+
+      pl022,wait-state:
+        description: Microwire interface - Wait state
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+      pl022,duplex:
+        description: Microwire interface - Full/Half duplex
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    spi@e0100000 {
+      compatible = "arm,pl022", "arm,primecell";
+      reg = <0xe0100000 0x1000>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+      interrupts = <0 31 0x4>;
+      dmas = <&dma_controller 23 1>,
+        <&dma_controller 24 0>;
+      dma-names = "rx", "tx";
+
+      m25p80@1 {
+        compatible = "st,m25p80";
+        reg = <1>;
+        spi-max-frequency = <12000000>;
+        spi-cpol;
+        spi-cpha;
+        pl022,interface = <0>;
+        pl022,com-mode = <0x2>;
+        pl022,rx-level-trig = <0>;
+        pl022,tx-level-trig = <0>;
+        pl022,ctrl-len = <0x11>;
+        pl022,wait-state = <0>;
+        pl022,duplex = <0>;
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
index adeeb63e84b9..bfc038b9478d 100644
--- a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
@@ -19,8 +19,11 @@ Required properties:
 - reg: chip-Select number (QSPI controller may connect 2 flashes)
 - spi-max-frequency: max frequency of spi bus
 
-Optional property:
+Optional properties:
 - spi-rx-bus-width: see ./spi-bus.txt for the description
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: DMA request names should include "tx" and "rx" if present.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt
deleted file mode 100644
index c75d604a8290..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-sun4i.txt
+++ /dev/null
@@ -1,23 +0,0 @@
-Allwinner A10 SPI controller
-
-Required properties:
-- compatible: Should be "allwinner,sun4-a10-spi".
-- reg: Should contain register location and length.
-- interrupts: Should contain interrupt.
-- clocks: phandle to the clocks feeding the SPI controller. Two are
-          needed:
-  - "ahb": the gated AHB parent clock
-  - "mod": the parent module clock
-- clock-names: Must contain the clock names described just above
-
-Example:
-
-spi1: spi@1c06000 {
-	compatible = "allwinner,sun4i-a10-spi";
-	reg = <0x01c06000 0x1000>;
-	interrupts = <11>;
-	clocks = <&ahb_gates 21>, <&spi1_clk>;
-	clock-names = "ahb", "mod";
-	#address-cells = <1>;
-	#size-cells = <0>;
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt
deleted file mode 100644
index 435a8e0731ac..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt
+++ /dev/null
@@ -1,44 +0,0 @@
-Allwinner A31/H3 SPI controller
-
-Required properties:
-- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi".
-- reg: Should contain register location and length.
-- interrupts: Should contain interrupt.
-- clocks: phandle to the clocks feeding the SPI controller. Two are
-          needed:
-  - "ahb": the gated AHB parent clock
-  - "mod": the parent module clock
-- clock-names: Must contain the clock names described just above
-- resets: phandle to the reset controller asserting this device in
-          reset
-
-Optional properties:
-- dmas: DMA specifiers for rx and tx dma. See the DMA client binding,
-	Documentation/devicetree/bindings/dma/dma.txt
-- dma-names: DMA request names should include "rx" and "tx" if present.
-
-Example:
-
-spi1: spi@1c69000 {
-	compatible = "allwinner,sun6i-a31-spi";
-	reg = <0x01c69000 0x1000>;
-	interrupts = <0 66 4>;
-	clocks = <&ahb1_gates 21>, <&spi1_clk>;
-	clock-names = "ahb", "mod";
-	resets = <&ahb1_rst 21>;
-};
-
-spi0: spi@1c68000 {
-	compatible = "allwinner,sun8i-h3-spi";
-	reg = <0x01c68000 0x1000>;
-	interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
-	clock-names = "ahb", "mod";
-	dmas = <&dma 23>, <&dma 23>;
-	dma-names = "rx", "tx";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins>;
-	resets = <&ccu RST_BUS_SPI0>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-};
diff --git a/Documentation/devicetree/bindings/spi/spi-synquacer.txt b/Documentation/devicetree/bindings/spi/spi-synquacer.txt
new file mode 100644
index 000000000000..291dfa692d0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-synquacer.txt
@@ -0,0 +1,27 @@
+* Socionext Synquacer HS-SPI bindings
+
+Required Properties:
+- compatible: should be "socionext,synquacer-spi"
+- reg: physical base address of the controller and length of memory mapped
+       region.
+- interrupts: should contain the "spi_rx", "spi_tx" and "spi_fault" interrupts.
+- clocks: core clock iHCLK. Optional rate clock iPCLK (default is iHCLK)
+- clock-names: Shall be "iHCLK" and "iPCLK" respectively
+
+Optional Properties:
+- socionext,use-rtm: boolean, if required to use "retimed clock" for RX
+- socionext,set-aces: boolean, if same active clock edges field to be set.
+
+Example:
+
+	spi0: spi@ff110000 {
+		compatible = "socionext,synquacer-spi";
+		reg = <0xff110000 0x1000>;
+		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_hsspi>;
+		clock-names = "iHCLK";
+		socionext,use-rtm;
+		socionext,set-aces;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt
deleted file mode 100644
index 7638b4968ddb..000000000000
--- a/Documentation/devicetree/bindings/spi/spi_pl022.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-ARM PL022 SPI controller
-
-Required properties:
-- compatible : "arm,pl022", "arm,primecell"
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain SPI controller interrupt
-- num-cs : total number of chipselects
-
-Optional properties:
-- cs-gpios : should specify GPIOs used for chipselects.
-  The gpios will be referred to as reg = <index> in the SPI child nodes.
-  If unspecified, a single SPI device without a chip select can be used.
-- pl022,autosuspend-delay : delay in ms following transfer completion before
-			    the runtime power management system suspends the
-			    device. A setting of 0 indicates no delay and the
-                            device will be suspended immediately
-- pl022,rt : indicates the controller should run the message pump with realtime
-             priority to minimise the transfer latency on the bus (boolean)
-- dmas : Two or more DMA channel specifiers following the convention outlined
-         in bindings/dma/dma.txt
-- dma-names: Names for the dma channels, if present. There must be at
-	     least one channel named "tx" for transmit and named "rx" for
-             receive.
-
-
-SPI slave nodes must be children of the SPI master node and can
-contain the following properties.
-
-- pl022,interface : interface type:
-	0: SPI
-	1: Texas Instruments Synchronous Serial Frame Format
-	2: Microwire (Half Duplex)
-- pl022,com-mode : specifies the transfer mode:
-	0: interrupt mode
-	1: polling mode (default mode if property not present)
-	2: DMA mode
-- pl022,rx-level-trig : Rx FIFO watermark level
-- pl022,tx-level-trig : Tx FIFO watermark level
-- pl022,ctrl-len : Microwire interface: Control length
-- pl022,wait-state : Microwire interface: Wait state
-- pl022,duplex : Microwire interface: Full/Half duplex
-
-
-Example:
-
-	spi@e0100000 {
-		compatible = "arm,pl022", "arm,primecell";
-		reg = <0xe0100000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <0 31 0x4>;
-		dmas = <&dma-controller 23 1>,
-			<&dma-controller 24 0>;
-		dma-names = "rx", "tx";
-
-		m25p80@1 {
-			compatible = "st,m25p80";
-			reg = <1>;
-			spi-max-frequency = <12000000>;
-			spi-cpol;
-			spi-cpha;
-			pl022,interface = <0>;
-			pl022,com-mode = <0x2>;
-			pl022,rx-level-trig = <0>;
-			pl022,tx-level-trig = <0>;
-			pl022,ctrl-len = <0x11>;
-			pl022,wait-state = <0>;
-			pl022,duplex = <0>;
-		};
-	};