Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc updates from Greg KH:
 "Here is the big set of char/misc driver patches for 4.17-rc1.

  There are a lot of little things in here, nothing huge, but all
  important to the different hardware types involved:

   -  thunderbolt driver updates

   -  parport updates (people still care...)

   -  nvmem driver updates

   -  mei updates (as always)

   -  hwtracing driver updates

   -  hyperv driver updates

   -  extcon driver updates

   -  ... and a handful of even smaller driver subsystem and individual
      driver updates

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
  hwtracing: Add HW tracing support menu
  intel_th: Add ACPI glue layer
  intel_th: Allow forcing host mode through drvdata
  intel_th: Pick up irq number from resources
  intel_th: Don't touch switch routing in host mode
  intel_th: Use correct method of finding hub
  intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
  stm class: Make dummy's master/channel ranges configurable
  stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
  MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
  hv: add SPDX license id to Kconfig
  hv: add SPDX license to trace
  Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
  Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
  /dev/mem: Avoid overwriting "err" in read_mem()
  eeprom: at24: use SPDX identifier instead of GPL boiler-plate
  eeprom: at24: simplify the i2c functionality checking
  eeprom: at24: fix a line break
  eeprom: at24: tweak newlines
  eeprom: at24: refactor at24_probe()
  ...

6 files changed, 337 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt
new file mode 100644
index 000000000000..22256e295a7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt
@@ -0,0 +1,49 @@
+Samsung micro-USB 11-pin connector
+==================================
+
+Samsung micro-USB 11-pin connector is an extension of micro-USB connector.
+It is present in multiple Samsung mobile devices.
+It has additional pins to route MHL traffic simultanously with USB.
+
+The bindings are superset of usb-connector bindings for micro-USB connector[1].
+
+Required properties:
+- compatible: must be: "samsung,usb-connector-11pin", "usb-b-connector",
+- type: must be "micro".
+
+Required nodes:
+- any data bus to the connector should be modeled using the OF graph bindings
+  specified in bindings/graph.txt, unless the bus is between parent node and
+  the connector. Since single connector can have multpile data buses every bus
+  has assigned OF graph port number as follows:
+    0: High Speed (HS),
+    3: Mobile High-Definition Link (MHL), specific to 11-pin Samsung micro-USB.
+
+[1]: bindings/connector/usb-connector.txt
+
+Example
+-------
+
+Micro-USB connector with HS lines routed via controller (MUIC) and MHL lines
+connected to HDMI-MHL bridge (sii8620):
+
+muic-max77843@66 {
+	...
+	usb_con: connector {
+		compatible = "samsung,usb-connector-11pin", "usb-b-connector";
+		label = "micro-USB";
+		type = "micro";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@3 {
+				reg = <3>;
+				usb_con_mhl: endpoint {
+					remote-endpoint = <&sii8620_mhl>;
+				};
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt
new file mode 100644
index 000000000000..e1463f14af38
--- /dev/null
+++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
@@ -0,0 +1,75 @@
+USB Connector
+=============
+
+USB connector node represents physical USB connector. It should be
+a child of USB interface controller.
+
+Required properties:
+- compatible: describes type of the connector, must be one of:
+    "usb-a-connector",
+    "usb-b-connector",
+    "usb-c-connector".
+
+Optional properties:
+- label: symbolic name for the connector,
+- type: size of the connector, should be specified in case of USB-A, USB-B
+  non-fullsize connectors: "mini", "micro".
+
+Required nodes:
+- any data bus to the connector should be modeled using the OF graph bindings
+  specified in bindings/graph.txt, unless the bus is between parent node and
+  the connector. Since single connector can have multpile data buses every bus
+  has assigned OF graph port number as follows:
+    0: High Speed (HS), present in all connectors,
+    1: Super Speed (SS), present in SS capable connectors,
+    2: Sideband use (SBU), present in USB-C.
+
+Examples
+--------
+
+1. Micro-USB connector with HS lines routed via controller (MUIC):
+
+muic-max77843@66 {
+	...
+	usb_con: connector {
+		compatible = "usb-b-connector";
+		label = "micro-USB";
+		type = "micro";
+	};
+};
+
+2. USB-C connector attached to CC controller (s2mm005), HS lines routed
+to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort.
+DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
+
+ccic: s2mm005@33 {
+	...
+	usb_con: connector {
+		compatible = "usb-c-connector";
+		label = "USB-C";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				usb_con_hs: endpoint {
+					remote-endpoint = <&max77865_usbc_hs>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				usb_con_ss: endpoint {
+					remote-endpoint = <&usbdrd_phy_ss>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				usb_con_sbu: endpoint {
+					remote-endpoint = <&dp_aux>;
+				};
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/fsi/fsi.txt b/Documentation/devicetree/bindings/fsi/fsi.txt
new file mode 100644
index 000000000000..ab516c673a4b
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi.txt
@@ -0,0 +1,151 @@
+FSI bus & engine generic device tree bindings
+=============================================
+
+The FSI bus is probe-able, so the OS is able to enumerate FSI slaves, and
+engines within those slaves. However, we have a facility to match devicetree
+nodes to probed engines. This allows for fsi engines to expose non-probeable
+busses, which are then exposed by the device tree. For example, an FSI engine
+that is an I2C master - the I2C bus can be described by the device tree under
+the engine's device tree node.
+
+FSI masters may require their own DT nodes (to describe the master HW itself);
+that requirement is defined by the master's implementation, and is described by
+the fsi-master-* binding specifications.
+
+Under the masters' nodes, we can describe the bus topology using nodes to
+represent the FSI slaves and their slave engines. As a basic outline:
+
+  fsi-master {
+      /* top-level of FSI bus topology, bound to an FSI master driver and
+       * exposes an FSI bus */
+
+      fsi-slave@<link,id> {
+          /* this node defines the FSI slave device, and is handled
+           * entirely with FSI core code */
+
+          fsi-slave-engine@<addr> {
+              /* this node defines the engine endpoint & address range, which
+               * is bound to the relevant fsi device driver */
+               ...
+          };
+
+          fsi-slave-engine@<addr> {
+              ...
+          };
+
+      };
+  };
+
+Note that since the bus is probe-able, some (or all) of the topology may
+not be described; this binding only provides an optional facility for
+adding subordinate device tree nodes as children of FSI engines.
+
+FSI masters
+-----------
+
+FSI master nodes declare themselves as such with the "fsi-master" compatible
+value. It's likely that an implementation-specific compatible value will
+be needed as well, for example:
+
+    compatible = "fsi-master-gpio", "fsi-master";
+
+Since the master nodes describe the top-level of the FSI topology, they also
+need to declare the FSI-standard addressing scheme. This requires two cells for
+addresses (link index and slave ID), and no size:
+
+    #address-cells = <2>;
+    #size-cells = <0>;
+
+An optional boolean property can be added to indicate that a particular master
+should not scan for connected devices at initialization time.  This is
+necessary in cases where a scan could cause arbitration issues with other
+masters that may be present on the bus.
+
+    no-scan-on-init;
+
+FSI slaves
+----------
+
+Slaves are identified by a (link-index, slave-id) pair, so require two cells
+for an address identifier. Since these are not a range, no size cells are
+required. For an example, a slave on link 1, with ID 2, could be represented
+as:
+
+    cfam@1,2 {
+        reg = <1 2>;
+	[...];
+    }
+
+Each slave provides an address-space, under which the engines are accessible.
+That address space has a maximum of 23 bits, so we use one cell to represent
+addresses and sizes in the slave address space:
+
+    #address-cells = <1>;
+    #size-cells = <1>;
+
+
+FSI engines (devices)
+---------------------
+
+Engines are identified by their address under the slaves' address spaces. We
+use a single cell for address and size. Engine nodes represent the endpoint
+FSI device, and are passed to those FSI device drivers' ->probe() functions.
+
+For example, for a slave using a single 0x400-byte page starting at address
+0xc00:
+
+    engine@c00 {
+        reg = <0xc00 0x400>;
+    };
+
+
+Full example
+------------
+
+Here's an example that illustrates:
+ - an FSI master
+   - connected to an FSI slave
+     - that contains an engine that is an I2C master
+       - connected to an I2C EEPROM
+
+The FSI master may be connected to additional slaves, and slaves may have
+additional engines, but they don't necessarily need to be describe in the
+device tree if no extra platform information is required.
+
+    /* The GPIO-based FSI master node, describing the top level of the
+     * FSI bus
+     */
+    gpio-fsi {
+        compatible = "fsi-master-gpio", "fsi-master";
+        #address-cells = <2>;
+        #size-cells = <0>;
+
+        /* A FSI slave (aka. CFAM) at link 0, ID 0. */
+        cfam@0,0 {
+            reg = <0 0>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            /* FSI engine at 0xc00, using a single page. In this example,
+             * it's an I2C master controller, so subnodes describe the
+             * I2C bus.
+             */
+            i2c-controller@c00 {
+                reg = <0xc00 0x400>;
+
+                /* Engine-specific data. In this case, we're describing an
+                 * I2C bus, so we're conforming to the generic I2C binding
+                 */
+                compatible = "some-vendor,fsi-i2c-controller";
+                #address-cells = <1>;
+                #size-cells = <1>;
+
+                /* I2C endpoint device: an Atmel EEPROM */
+                eeprom@50 {
+                    compatible = "atmel,24c256";
+                    reg = <0x50>;
+                    pagesize = <64>;
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
index 514d82ced95b..69aadee00d5f 100644
--- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
+++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
@@ -109,9 +109,50 @@ lpc: lpc@1e789000 {
 	};
 };
 
+BMC Node Children
+==================
+
+
 Host Node Children
 ==================
 
+LPC Host Interface Controller
+-------------------
+
+The LPC Host Interface Controller manages functions exposed to the host such as
+LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
+management and bus snoop configuration.
+
+Required properties:
+
+- compatible:	One of:
+		"aspeed,ast2400-lpc-ctrl";
+		"aspeed,ast2500-lpc-ctrl";
+
+- reg:		contains offset/length values of the host interface controller
+		memory regions
+
+- clocks:	contains a phandle to the syscon node describing the clocks.
+		There should then be one cell representing the clock to use
+
+- memory-region: A phandle to a reserved_memory region to be used for the LPC
+		to AHB mapping
+
+- flash:	A phandle to the SPI flash controller containing the flash to
+		be exposed over the LPC to AHB mapping
+
+Example:
+
+lpc-host@80 {
+	lpc_ctrl: lpc-ctrl@0 {
+		compatible = "aspeed,ast2500-lpc-ctrl";
+		reg = <0x0 0x80>;
+		clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+		memory-region = <&flash_memory>;
+		flash = <&spi>;
+	};
+};
+
 LPC Host Controller
 -------------------
 
diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
index f162c72b4e36..729f6747813b 100644
--- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
+++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt
@@ -11,17 +11,32 @@ Required properties:
 	"fsl,imx6ul-ocotp" (i.MX6UL),
 	"fsl,imx7d-ocotp" (i.MX7D/S),
 	followed by "syscon".
+- #address-cells : Should be 1
+- #size-cells : Should be 1
 - reg: Should contain the register base and length.
 - clocks: Should contain a phandle pointing to the gated peripheral clock.
 
 Optional properties:
 - read-only: disable write access
 
-Example:
+Optional Child nodes:
+
+- Data cells of ocotp:
+  Detailed bindings are described in bindings/nvmem/nvmem.txt
 
+Example:
 	ocotp: ocotp@21bc000 {
-		compatible = "fsl,imx6q-ocotp", "syscon";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,imx6sx-ocotp", "syscon";
 		reg = <0x021bc000 0x4000>;
-		clocks = <&clks IMX6QDL_CLK_IIM>;
-		read-only;
+		clocks = <&clks IMX6SX_CLK_OCOTP>;
+
+		tempmon_calib: calib@38 {
+			reg = <0x38 4>;
+		};
+
+		tempmon_temp_grade: temp-grade@20 {
+			reg = <0x20 4>;
+		};
 	};
diff --git a/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt
index 20bc49b49799..3cb170896658 100644
--- a/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt
+++ b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt
@@ -1,5 +1,5 @@
 Device tree bindings for Low Power General Purpose Register found in i.MX6Q/D
-Secure Non-Volatile Storage.
+and i.MX7 Secure Non-Volatile Storage.
 
 This DT node should be represented as a sub-node of a "syscon",
 "simple-mfd" node.
@@ -8,6 +8,7 @@ Required properties:
 - compatible: should be one of the fallowing variants:
 	"fsl,imx6q-snvs-lpgpr" for Freescale i.MX6Q/D/DL/S
 	"fsl,imx6ul-snvs-lpgpr" for Freescale i.MX6UL
+	"fsl,imx7d-snvs-lpgpr" for Freescale i.MX7D/S
 
 Example:
 snvs: snvs@020cc000 {