serial: remove cris/etrax uart drivers

The cris architecture is getting removed, so we don't need the
uart driver any more.

Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

6 files changed, 0 insertions, 5376 deletions

diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
deleted file mode 100644
index 048c3818c826..000000000000
--- a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-ETRAX FS UART
-
-Required properties:
-- compatible : "axis,etraxfs-uart"
-- reg: offset and length of the register set for the device.
-- interrupts: device interrupt
-
-Optional properties:
-- {dtr,dsr,rng,dcd}-gpios: specify a GPIO for DTR/DSR/RI/DCD
-  line respectively.
-
-Example:
-
-serial@b00260000 {
-	compatible = "axis,etraxfs-uart";
-	reg = <0xb0026000 0x1000>;
-	interrupts = <68>;
-	dtr-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>;
-	dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>;
-	rng-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>;
-	dcd-gpios = <&sysgpio 3 GPIO_ACTIVE_LOW>;
-};
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 3682fd3e960c..f6e09326042d 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1114,17 +1114,6 @@ config SERIAL_VT8500_CONSOLE
 	depends on SERIAL_VT8500=y
 	select SERIAL_CORE_CONSOLE
 
-config SERIAL_ETRAXFS
-	bool "ETRAX FS serial port support"
-	depends on ETRAX_ARCH_V32 && OF
-	select SERIAL_CORE
-	select SERIAL_MCTRL_GPIO if GPIOLIB
-
-config SERIAL_ETRAXFS_CONSOLE
-	bool "ETRAX FS serial console support"
-	depends on SERIAL_ETRAXFS
-	select SERIAL_CORE_CONSOLE
-
 config SERIAL_NETX
 	tristate "NetX serial port support"
 	depends on ARCH_NETX
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 842d185d697e..c21835dc16b2 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -51,8 +51,6 @@ obj-$(CONFIG_SERIAL_M32R_SIO) += m32r_sio.o
 obj-$(CONFIG_SERIAL_MPSC) += mpsc.o
 obj-$(CONFIG_SERIAL_MESON) += meson_uart.o
 obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
-obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
-obj-$(CONFIG_SERIAL_ETRAXFS) += etraxfs-uart.o
 obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
 obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o
 obj-$(CONFIG_SERIAL_JSM) += jsm/
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
deleted file mode 100644
index c9458a033e3c..000000000000
--- a/drivers/tty/serial/crisv10.c
+++ /dev/null
@@ -1,4248 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Serial port driver for the ETRAX 100LX chip
- *
- *    Copyright (C) 1998-2007  Axis Communications AB
- *
- *    Many, many authors. Based once upon a time on serial.c for 16x50.
- *
- */
-
-static char *serial_version = "$Revision: 1.25 $";
-
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched/signal.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/major.h>
-#include <linux/string.h>
-#include <linux/fcntl.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/mutex.h>
-#include <linux/bitops.h>
-#include <linux/seq_file.h>
-#include <linux/delay.h>
-#include <linux/uaccess.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/dma.h>
-
-#include <arch/svinto.h>
-#include <arch/system.h>
-
-/* non-arch dependent serial structures are in linux/serial.h */
-#include <linux/serial.h>
-/* while we keep our own stuff (struct e100_serial) in a local .h file */
-#include "crisv10.h"
-#include <asm/fasttimer.h>
-#include <arch/io_interface_mux.h>
-
-#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
-#ifndef CONFIG_ETRAX_FAST_TIMER
-#error "Enable FAST_TIMER to use SERIAL_FAST_TIMER"
-#endif
-#endif
-
-#if defined(CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS) && \
-           (CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS == 0)
-#error "RX_TIMEOUT_TICKS == 0 not allowed, use 1"
-#endif
-
-/*
- * All of the compatibilty code so we can compile serial.c against
- * older kernels is hidden in serial_compat.h
- */
-#if defined(LOCAL_HEADERS)
-#include "serial_compat.h"
-#endif
-
-struct tty_driver *serial_driver;
-
-/* number of characters left in xmit buffer before we ask for more */
-#define WAKEUP_CHARS 256
-
-//#define SERIAL_DEBUG_INTR
-//#define SERIAL_DEBUG_OPEN
-//#define SERIAL_DEBUG_FLOW
-//#define SERIAL_DEBUG_DATA
-//#define SERIAL_DEBUG_THROTTLE
-//#define SERIAL_DEBUG_IO  /* Debug for Extra control and status pins */
-//#define SERIAL_DEBUG_LINE 0 /* What serport we want to debug */
-
-/* Enable this to use serial interrupts to handle when you
-   expect the first received event on the serial port to
-   be an error, break or similar. Used to be able to flash IRMA
-   from eLinux */
-#define SERIAL_HANDLE_EARLY_ERRORS
-
-/* Currently 16 descriptors x 128 bytes = 2048 bytes */
-#define SERIAL_DESCR_BUF_SIZE 256
-
-#define SERIAL_PRESCALE_BASE 3125000 /* 3.125MHz */
-#define DEF_BAUD_BASE SERIAL_PRESCALE_BASE
-
-/* We don't want to load the system with massive fast timer interrupt
- * on high baudrates so limit it to 250 us (4kHz) */
-#define MIN_FLUSH_TIME_USEC 250
-
-/* Add an x here to log a lot of timer stuff */
-#define TIMERD(x)
-/* Debug details of interrupt handling */
-#define DINTR1(x)  /* irq on/off, errors */
-#define DINTR2(x)    /* tx and rx */
-/* Debug flip buffer stuff */
-#define DFLIP(x)
-/* Debug flow control and overview of data flow */
-#define DFLOW(x)
-#define DBAUD(x)
-#define DLOG_INT_TRIG(x)
-
-//#define DEBUG_LOG_INCLUDED
-#ifndef DEBUG_LOG_INCLUDED
-#define DEBUG_LOG(line, string, value)
-#else
-struct debug_log_info
-{
-	unsigned long time;
-	unsigned long timer_data;
-//  int line;
-	const char *string;
-	int value;
-};
-#define DEBUG_LOG_SIZE 4096
-
-struct debug_log_info debug_log[DEBUG_LOG_SIZE];
-int debug_log_pos = 0;
-
-#define DEBUG_LOG(_line, _string, _value) do { \
-  if ((_line) == SERIAL_DEBUG_LINE) {\
-    debug_log_func(_line, _string, _value); \
-  }\
-}while(0)
-
-void debug_log_func(int line, const char *string, int value)
-{
-	if (debug_log_pos < DEBUG_LOG_SIZE) {
-		debug_log[debug_log_pos].time = jiffies;
-		debug_log[debug_log_pos].timer_data = *R_TIMER_DATA;
-//    debug_log[debug_log_pos].line = line;
-		debug_log[debug_log_pos].string = string;
-		debug_log[debug_log_pos].value = value;
-		debug_log_pos++;
-	}
-	/*printk(string, value);*/
-}
-#endif
-
-#ifndef CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS
-/* Default number of timer ticks before flushing rx fifo
- * When using "little data, low latency applications: use 0
- * When using "much data applications (PPP)" use ~5
- */
-#define CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS 5
-#endif
-
-unsigned long timer_data_to_ns(unsigned long timer_data);
-
-static void change_speed(struct e100_serial *info);
-static void rs_throttle(struct tty_struct * tty);
-static void rs_wait_until_sent(struct tty_struct *tty, int timeout);
-static int rs_write(struct tty_struct *tty,
-		const unsigned char *buf, int count);
-#ifdef CONFIG_ETRAX_RS485
-static int e100_write_rs485(struct tty_struct *tty,
-		const unsigned char *buf, int count);
-#endif
-static int get_lsr_info(struct e100_serial *info, unsigned int *value);
-
-
-#define DEF_BAUD 115200   /* 115.2 kbit/s */
-#define DEF_RX 0x20  /* or SERIAL_CTRL_W >> 8 */
-/* Default value of tx_ctrl register: has txd(bit 7)=1 (idle) as default */
-#define DEF_TX 0x80  /* or SERIAL_CTRL_B */
-
-/* offsets from R_SERIALx_CTRL */
-
-#define REG_DATA 0
-#define REG_DATA_STATUS32 0 /* this is the 32 bit register R_SERIALx_READ */
-#define REG_TR_DATA 0
-#define REG_STATUS 1
-#define REG_TR_CTRL 1
-#define REG_REC_CTRL 2
-#define REG_BAUD 3
-#define REG_XOFF 4  /* this is a 32 bit register */
-
-/* The bitfields are the same for all serial ports */
-#define SER_RXD_MASK         IO_MASK(R_SERIAL0_STATUS, rxd)
-#define SER_DATA_AVAIL_MASK  IO_MASK(R_SERIAL0_STATUS, data_avail)
-#define SER_FRAMING_ERR_MASK IO_MASK(R_SERIAL0_STATUS, framing_err)
-#define SER_PAR_ERR_MASK     IO_MASK(R_SERIAL0_STATUS, par_err)
-#define SER_OVERRUN_MASK     IO_MASK(R_SERIAL0_STATUS, overrun)
-
-#define SER_ERROR_MASK (SER_OVERRUN_MASK | SER_PAR_ERR_MASK | SER_FRAMING_ERR_MASK)
-
-/* Values for info->errorcode */
-#define ERRCODE_SET_BREAK    (TTY_BREAK)
-#define ERRCODE_INSERT        0x100
-#define ERRCODE_INSERT_BREAK (ERRCODE_INSERT | TTY_BREAK)
-
-#define FORCE_EOP(info)  *R_SET_EOP = 1U << info->iseteop;
-
-/*
- * General note regarding the use of IO_* macros in this file:
- *
- * We will use the bits defined for DMA channel 6 when using various
- * IO_* macros (e.g. IO_STATE, IO_MASK, IO_EXTRACT) and _assume_ they are
- * the same for all channels (which of course they are).
- *
- * We will also use the bits defined for serial port 0 when writing commands
- * to the different ports, as these bits too are the same for all ports.
- */
-
-
-/* Mask for the irqs possibly enabled in R_IRQ_MASK1_RD etc. */
-static const unsigned long e100_ser_int_mask = 0
-#ifdef CONFIG_ETRAX_SERIAL_PORT0
-| IO_MASK(R_IRQ_MASK1_RD, ser0_data) | IO_MASK(R_IRQ_MASK1_RD, ser0_ready)
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT1
-| IO_MASK(R_IRQ_MASK1_RD, ser1_data) | IO_MASK(R_IRQ_MASK1_RD, ser1_ready)
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT2
-| IO_MASK(R_IRQ_MASK1_RD, ser2_data) | IO_MASK(R_IRQ_MASK1_RD, ser2_ready)
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT3
-| IO_MASK(R_IRQ_MASK1_RD, ser3_data) | IO_MASK(R_IRQ_MASK1_RD, ser3_ready)
-#endif
-;
-unsigned long r_alt_ser_baudrate_shadow = 0;
-
-/* this is the data for the four serial ports in the etrax100 */
-/*  DMA2(ser2), DMA4(ser3), DMA6(ser0) or DMA8(ser1) */
-/* R_DMA_CHx_CLR_INTR, R_DMA_CHx_FIRST, R_DMA_CHx_CMD */
-
-static struct e100_serial rs_table[] = {
-	{ .baud        = DEF_BAUD,
-	  .ioport        = (unsigned char *)R_SERIAL0_CTRL,
-	  .irq         = 1U << 12, /* uses DMA 6 and 7 */
-	  .oclrintradr = R_DMA_CH6_CLR_INTR,
-	  .ofirstadr   = R_DMA_CH6_FIRST,
-	  .ocmdadr     = R_DMA_CH6_CMD,
-	  .ostatusadr  = R_DMA_CH6_STATUS,
-	  .iclrintradr = R_DMA_CH7_CLR_INTR,
-	  .ifirstadr   = R_DMA_CH7_FIRST,
-	  .icmdadr     = R_DMA_CH7_CMD,
-	  .idescradr   = R_DMA_CH7_DESCR,
-	  .rx_ctrl     = DEF_RX,
-	  .tx_ctrl     = DEF_TX,
-	  .iseteop     = 2,
-	  .dma_owner   = dma_ser0,
-	  .io_if       = if_serial_0,
-#ifdef CONFIG_ETRAX_SERIAL_PORT0
-          .enabled  = 1,
-#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT
-	  .dma_out_enabled = 1,
-	  .dma_out_nbr = SER0_TX_DMA_NBR,
-	  .dma_out_irq_nbr = SER0_DMA_TX_IRQ_NBR,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = "serial 0 dma tr",
-#else
-	  .dma_out_enabled = 0,
-	  .dma_out_nbr = UINT_MAX,
-	  .dma_out_irq_nbr = 0,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = NULL,
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN
-	  .dma_in_enabled = 1,
-	  .dma_in_nbr = SER0_RX_DMA_NBR,
-	  .dma_in_irq_nbr = SER0_DMA_RX_IRQ_NBR,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = "serial 0 dma rec",
-#else
-	  .dma_in_enabled = 0,
-	  .dma_in_nbr = UINT_MAX,
-	  .dma_in_irq_nbr = 0,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = NULL,
-#endif
-#else
-          .enabled  = 0,
-	  .io_if_description = NULL,
-	  .dma_out_enabled = 0,
-	  .dma_in_enabled = 0
-#endif
-
-},  /* ttyS0 */
-	{ .baud        = DEF_BAUD,
-	  .ioport        = (unsigned char *)R_SERIAL1_CTRL,
-	  .irq         = 1U << 16, /* uses DMA 8 and 9 */
-	  .oclrintradr = R_DMA_CH8_CLR_INTR,
-	  .ofirstadr   = R_DMA_CH8_FIRST,
-	  .ocmdadr     = R_DMA_CH8_CMD,
-	  .ostatusadr  = R_DMA_CH8_STATUS,
-	  .iclrintradr = R_DMA_CH9_CLR_INTR,
-	  .ifirstadr   = R_DMA_CH9_FIRST,
-	  .icmdadr     = R_DMA_CH9_CMD,
-	  .idescradr   = R_DMA_CH9_DESCR,
-	  .rx_ctrl     = DEF_RX,
-	  .tx_ctrl     = DEF_TX,
-	  .iseteop     = 3,
-	  .dma_owner   = dma_ser1,
-	  .io_if       = if_serial_1,
-#ifdef CONFIG_ETRAX_SERIAL_PORT1
-          .enabled  = 1,
-	  .io_if_description = "ser1",
-#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT
-	  .dma_out_enabled = 1,
-	  .dma_out_nbr = SER1_TX_DMA_NBR,
-	  .dma_out_irq_nbr = SER1_DMA_TX_IRQ_NBR,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = "serial 1 dma tr",
-#else
-	  .dma_out_enabled = 0,
-	  .dma_out_nbr = UINT_MAX,
-	  .dma_out_irq_nbr = 0,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = NULL,
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN
-	  .dma_in_enabled = 1,
-	  .dma_in_nbr = SER1_RX_DMA_NBR,
-	  .dma_in_irq_nbr = SER1_DMA_RX_IRQ_NBR,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = "serial 1 dma rec",
-#else
-	  .dma_in_enabled = 0,
-	  .dma_in_enabled = 0,
-	  .dma_in_nbr = UINT_MAX,
-	  .dma_in_irq_nbr = 0,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = NULL,
-#endif
-#else
-          .enabled  = 0,
-	  .io_if_description = NULL,
-	  .dma_in_irq_nbr = 0,
-	  .dma_out_enabled = 0,
-	  .dma_in_enabled = 0
-#endif
-},  /* ttyS1 */
-
-	{ .baud        = DEF_BAUD,
-	  .ioport        = (unsigned char *)R_SERIAL2_CTRL,
-	  .irq         = 1U << 4,  /* uses DMA 2 and 3 */
-	  .oclrintradr = R_DMA_CH2_CLR_INTR,
-	  .ofirstadr   = R_DMA_CH2_FIRST,
-	  .ocmdadr     = R_DMA_CH2_CMD,
-	  .ostatusadr  = R_DMA_CH2_STATUS,
-	  .iclrintradr = R_DMA_CH3_CLR_INTR,
-	  .ifirstadr   = R_DMA_CH3_FIRST,
-	  .icmdadr     = R_DMA_CH3_CMD,
-	  .idescradr   = R_DMA_CH3_DESCR,
-	  .rx_ctrl     = DEF_RX,
-	  .tx_ctrl     = DEF_TX,
-	  .iseteop     = 0,
-	  .dma_owner   = dma_ser2,
-	  .io_if       = if_serial_2,
-#ifdef CONFIG_ETRAX_SERIAL_PORT2
-          .enabled  = 1,
-	  .io_if_description = "ser2",
-#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT
-	  .dma_out_enabled = 1,
-	  .dma_out_nbr = SER2_TX_DMA_NBR,
-	  .dma_out_irq_nbr = SER2_DMA_TX_IRQ_NBR,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = "serial 2 dma tr",
-#else
-	  .dma_out_enabled = 0,
-	  .dma_out_nbr = UINT_MAX,
-	  .dma_out_irq_nbr = 0,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = NULL,
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN
-	  .dma_in_enabled = 1,
-	  .dma_in_nbr = SER2_RX_DMA_NBR,
-	  .dma_in_irq_nbr = SER2_DMA_RX_IRQ_NBR,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = "serial 2 dma rec",
-#else
-	  .dma_in_enabled = 0,
-	  .dma_in_nbr = UINT_MAX,
-	  .dma_in_irq_nbr = 0,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = NULL,
-#endif
-#else
-          .enabled  = 0,
-	  .io_if_description = NULL,
-	  .dma_out_enabled = 0,
-	  .dma_in_enabled = 0
-#endif
- },  /* ttyS2 */
-
-	{ .baud        = DEF_BAUD,
-	  .ioport        = (unsigned char *)R_SERIAL3_CTRL,
-	  .irq         = 1U << 8,  /* uses DMA 4 and 5 */
-	  .oclrintradr = R_DMA_CH4_CLR_INTR,
-	  .ofirstadr   = R_DMA_CH4_FIRST,
-	  .ocmdadr     = R_DMA_CH4_CMD,
-	  .ostatusadr  = R_DMA_CH4_STATUS,
-	  .iclrintradr = R_DMA_CH5_CLR_INTR,
-	  .ifirstadr   = R_DMA_CH5_FIRST,
-	  .icmdadr     = R_DMA_CH5_CMD,
-	  .idescradr   = R_DMA_CH5_DESCR,
-	  .rx_ctrl     = DEF_RX,
-	  .tx_ctrl     = DEF_TX,
-	  .iseteop     = 1,
-	  .dma_owner   = dma_ser3,
-	  .io_if       = if_serial_3,
-#ifdef CONFIG_ETRAX_SERIAL_PORT3
-          .enabled  = 1,
-	  .io_if_description = "ser3",
-#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT
-	  .dma_out_enabled = 1,
-	  .dma_out_nbr = SER3_TX_DMA_NBR,
-	  .dma_out_irq_nbr = SER3_DMA_TX_IRQ_NBR,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = "serial 3 dma tr",
-#else
-	  .dma_out_enabled = 0,
-	  .dma_out_nbr = UINT_MAX,
-	  .dma_out_irq_nbr = 0,
-	  .dma_out_irq_flags = 0,
-	  .dma_out_irq_description = NULL,
-#endif
-#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN
-	  .dma_in_enabled = 1,
-	  .dma_in_nbr = SER3_RX_DMA_NBR,
-	  .dma_in_irq_nbr = SER3_DMA_RX_IRQ_NBR,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = "serial 3 dma rec",
-#else
-	  .dma_in_enabled = 0,
-	  .dma_in_nbr = UINT_MAX,
-	  .dma_in_irq_nbr = 0,
-	  .dma_in_irq_flags = 0,
-	  .dma_in_irq_description = NULL
-#endif
-#else
-          .enabled  = 0,
-	  .io_if_description = NULL,
-	  .dma_out_enabled = 0,
-	  .dma_in_enabled = 0
-#endif
- }   /* ttyS3 */
-};
-
-
-#define NR_PORTS (sizeof(rs_table)/sizeof(struct e100_serial))
-
-#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
-static struct fast_timer fast_timers[NR_PORTS];
-#endif
-
-/* RS-485 */
-#if defined(CONFIG_ETRAX_RS485)
-#ifdef CONFIG_ETRAX_FAST_TIMER
-static struct fast_timer fast_timers_rs485[NR_PORTS];
-#endif
-#if defined(CONFIG_ETRAX_RS485_ON_PA)
-static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT;
-#endif
-#endif
-
-/* Info and macros needed for each ports extra control/status signals. */
-#define E100_STRUCT_PORT(line, pinname) \
- ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
-		(R_PORT_PA_DATA): ( \
- (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
-		(R_PORT_PB_DATA):&dummy_ser[line]))
-
-#define E100_STRUCT_SHADOW(line, pinname) \
- ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
-		(&port_pa_data_shadow): ( \
- (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
-		(&port_pb_data_shadow):&dummy_ser[line]))
-#define E100_STRUCT_MASK(line, pinname) \
- ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
-		(1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT): ( \
- (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
-		(1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT):DUMMY_##pinname##_MASK))
-
-#define DUMMY_DTR_MASK 1
-#define DUMMY_RI_MASK  2
-#define DUMMY_DSR_MASK 4
-#define DUMMY_CD_MASK  8
-static unsigned char dummy_ser[NR_PORTS] = {0xFF, 0xFF, 0xFF,0xFF};
-
-/* If not all status pins are used or disabled, use mixed mode */
-#ifdef CONFIG_ETRAX_SERIAL_PORT0
-
-#define SER0_PA_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PA_BIT+CONFIG_ETRAX_SER0_RI_ON_PA_BIT+CONFIG_ETRAX_SER0_DSR_ON_PA_BIT+CONFIG_ETRAX_SER0_CD_ON_PA_BIT)
-
-#if SER0_PA_BITSUM != -4
-#  if CONFIG_ETRAX_SER0_DTR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER0_RI_ON_PA_BIT == -1
-#   ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER0_DSR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER0_CD_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#define SER0_PB_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PB_BIT+CONFIG_ETRAX_SER0_RI_ON_PB_BIT+CONFIG_ETRAX_SER0_DSR_ON_PB_BIT+CONFIG_ETRAX_SER0_CD_ON_PB_BIT)
-
-#if SER0_PB_BITSUM != -4
-#  if CONFIG_ETRAX_SER0_DTR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER0_RI_ON_PB_BIT == -1
-#   ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER0_DSR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER0_CD_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#endif /* PORT0 */
-
-
-#ifdef CONFIG_ETRAX_SERIAL_PORT1
-
-#define SER1_PA_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PA_BIT+CONFIG_ETRAX_SER1_RI_ON_PA_BIT+CONFIG_ETRAX_SER1_DSR_ON_PA_BIT+CONFIG_ETRAX_SER1_CD_ON_PA_BIT)
-
-#if SER1_PA_BITSUM != -4
-#  if CONFIG_ETRAX_SER1_DTR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER1_RI_ON_PA_BIT == -1
-#   ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER1_DSR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER1_CD_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#define SER1_PB_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PB_BIT+CONFIG_ETRAX_SER1_RI_ON_PB_BIT+CONFIG_ETRAX_SER1_DSR_ON_PB_BIT+CONFIG_ETRAX_SER1_CD_ON_PB_BIT)
-
-#if SER1_PB_BITSUM != -4
-#  if CONFIG_ETRAX_SER1_DTR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER1_RI_ON_PB_BIT == -1
-#   ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER1_DSR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER1_CD_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#endif /* PORT1 */
-
-#ifdef CONFIG_ETRAX_SERIAL_PORT2
-
-#define SER2_PA_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PA_BIT+CONFIG_ETRAX_SER2_RI_ON_PA_BIT+CONFIG_ETRAX_SER2_DSR_ON_PA_BIT+CONFIG_ETRAX_SER2_CD_ON_PA_BIT)
-
-#if SER2_PA_BITSUM != -4
-#  if CONFIG_ETRAX_SER2_DTR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER2_RI_ON_PA_BIT == -1
-#   ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER2_DSR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER2_CD_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#define SER2_PB_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PB_BIT+CONFIG_ETRAX_SER2_RI_ON_PB_BIT+CONFIG_ETRAX_SER2_DSR_ON_PB_BIT+CONFIG_ETRAX_SER2_CD_ON_PB_BIT)
-
-#if SER2_PB_BITSUM != -4
-#  if CONFIG_ETRAX_SER2_DTR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER2_RI_ON_PB_BIT == -1
-#   ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER2_DSR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER2_CD_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#endif /* PORT2 */
-
-#ifdef CONFIG_ETRAX_SERIAL_PORT3
-
-#define SER3_PA_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PA_BIT+CONFIG_ETRAX_SER3_RI_ON_PA_BIT+CONFIG_ETRAX_SER3_DSR_ON_PA_BIT+CONFIG_ETRAX_SER3_CD_ON_PA_BIT)
-
-#if SER3_PA_BITSUM != -4
-#  if CONFIG_ETRAX_SER3_DTR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER3_RI_ON_PA_BIT == -1
-#   ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER3_DSR_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER3_CD_ON_PA_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#define SER3_PB_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PB_BIT+CONFIG_ETRAX_SER3_RI_ON_PB_BIT+CONFIG_ETRAX_SER3_DSR_ON_PB_BIT+CONFIG_ETRAX_SER3_CD_ON_PB_BIT)
-
-#if SER3_PB_BITSUM != -4
-#  if CONFIG_ETRAX_SER3_DTR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#   endif
-# if CONFIG_ETRAX_SER3_RI_ON_PB_BIT == -1
-#   ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#     define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#   endif
-#  endif
-#  if CONFIG_ETRAX_SER3_DSR_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#  if CONFIG_ETRAX_SER3_CD_ON_PB_BIT == -1
-#    ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
-#      define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
-#    endif
-#  endif
-#endif
-
-#endif /* PORT3 */
-
-
-#if defined(CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED) || \
-    defined(CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED) || \
-    defined(CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED) || \
-    defined(CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED)
-#define ETRAX_SERX_DTR_RI_DSR_CD_MIXED
-#endif
-
-#ifdef ETRAX_SERX_DTR_RI_DSR_CD_MIXED
-/* The pins can be mixed on PA and PB */
-#define CONTROL_PINS_PORT_NOT_USED(line) \
-  &dummy_ser[line], &dummy_ser[line], \
-  &dummy_ser[line], &dummy_ser[line], \
-  &dummy_ser[line], &dummy_ser[line], \
-  &dummy_ser[line], &dummy_ser[line], \
-  DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK
-
-
-struct control_pins
-{
-	volatile unsigned char *dtr_port;
-	unsigned char          *dtr_shadow;
-	volatile unsigned char *ri_port;
-	unsigned char          *ri_shadow;
-	volatile unsigned char *dsr_port;
-	unsigned char          *dsr_shadow;
-	volatile unsigned char *cd_port;
-	unsigned char          *cd_shadow;
-
-	unsigned char dtr_mask;
-	unsigned char ri_mask;
-	unsigned char dsr_mask;
-	unsigned char cd_mask;
-};
-
-static const struct control_pins e100_modem_pins[NR_PORTS] =
-{
-	/* Ser 0 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT0
-	E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR),
-	E100_STRUCT_PORT(0,RI),  E100_STRUCT_SHADOW(0,RI),
-	E100_STRUCT_PORT(0,DSR), E100_STRUCT_SHADOW(0,DSR),
-	E100_STRUCT_PORT(0,CD),  E100_STRUCT_SHADOW(0,CD),
-	E100_STRUCT_MASK(0,DTR),
-	E100_STRUCT_MASK(0,RI),
-	E100_STRUCT_MASK(0,DSR),
-	E100_STRUCT_MASK(0,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(0)
-#endif
-	},
-
-	/* Ser 1 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT1
-	E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR),
-	E100_STRUCT_PORT(1,RI),  E100_STRUCT_SHADOW(1,RI),
-	E100_STRUCT_PORT(1,DSR), E100_STRUCT_SHADOW(1,DSR),
-	E100_STRUCT_PORT(1,CD),  E100_STRUCT_SHADOW(1,CD),
-	E100_STRUCT_MASK(1,DTR),
-	E100_STRUCT_MASK(1,RI),
-	E100_STRUCT_MASK(1,DSR),
-	E100_STRUCT_MASK(1,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(1)
-#endif
-	},
-
-	/* Ser 2 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT2
-	E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR),
-	E100_STRUCT_PORT(2,RI),  E100_STRUCT_SHADOW(2,RI),
-	E100_STRUCT_PORT(2,DSR), E100_STRUCT_SHADOW(2,DSR),
-	E100_STRUCT_PORT(2,CD),  E100_STRUCT_SHADOW(2,CD),
-	E100_STRUCT_MASK(2,DTR),
-	E100_STRUCT_MASK(2,RI),
-	E100_STRUCT_MASK(2,DSR),
-	E100_STRUCT_MASK(2,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(2)
-#endif
-	},
-
-	/* Ser 3 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT3
-	E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR),
-	E100_STRUCT_PORT(3,RI),  E100_STRUCT_SHADOW(3,RI),
-	E100_STRUCT_PORT(3,DSR), E100_STRUCT_SHADOW(3,DSR),
-	E100_STRUCT_PORT(3,CD),  E100_STRUCT_SHADOW(3,CD),
-	E100_STRUCT_MASK(3,DTR),
-	E100_STRUCT_MASK(3,RI),
-	E100_STRUCT_MASK(3,DSR),
-	E100_STRUCT_MASK(3,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(3)
-#endif
-	}
-};
-#else  /* ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
-
-/* All pins are on either PA or PB for each serial port */
-#define CONTROL_PINS_PORT_NOT_USED(line) \
-  &dummy_ser[line], &dummy_ser[line], \
-  DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK
-
-
-struct control_pins
-{
-	volatile unsigned char *port;
-	unsigned char          *shadow;
-
-	unsigned char dtr_mask;
-	unsigned char ri_mask;
-	unsigned char dsr_mask;
-	unsigned char cd_mask;
-};
-
-#define dtr_port port
-#define dtr_shadow shadow
-#define ri_port port
-#define ri_shadow shadow
-#define dsr_port port
-#define dsr_shadow shadow
-#define cd_port port
-#define cd_shadow shadow
-
-static const struct control_pins e100_modem_pins[NR_PORTS] =
-{
-	/* Ser 0 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT0
-	E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR),
-	E100_STRUCT_MASK(0,DTR),
-	E100_STRUCT_MASK(0,RI),
-	E100_STRUCT_MASK(0,DSR),
-	E100_STRUCT_MASK(0,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(0)
-#endif
-	},
-
-	/* Ser 1 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT1
-	E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR),
-	E100_STRUCT_MASK(1,DTR),
-	E100_STRUCT_MASK(1,RI),
-	E100_STRUCT_MASK(1,DSR),
-	E100_STRUCT_MASK(1,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(1)
-#endif
-	},
-
-	/* Ser 2 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT2
-	E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR),
-	E100_STRUCT_MASK(2,DTR),
-	E100_STRUCT_MASK(2,RI),
-	E100_STRUCT_MASK(2,DSR),
-	E100_STRUCT_MASK(2,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(2)
-#endif
-	},
-
-	/* Ser 3 */
-	{
-#ifdef CONFIG_ETRAX_SERIAL_PORT3
-	E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR),
-	E100_STRUCT_MASK(3,DTR),
-	E100_STRUCT_MASK(3,RI),
-	E100_STRUCT_MASK(3,DSR),
-	E100_STRUCT_MASK(3,CD)
-#else
-	CONTROL_PINS_PORT_NOT_USED(3)
-#endif
-	}
-};
-#endif /* !ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
-
-#define E100_RTS_MASK 0x20
-#define E100_CTS_MASK 0x40
-
-/* All serial port signals are active low:
- * active   = 0 -> 3.3V to RS-232 driver -> -12V on RS-232 level
- * inactive = 1 -> 0V   to RS-232 driver -> +12V on RS-232 level
- *
- * These macros returns the pin value: 0=0V, >=1 = 3.3V on ETRAX chip
- */
-
-/* Output */
-#define E100_RTS_GET(info) ((info)->rx_ctrl & E100_RTS_MASK)
-/* Input */
-#define E100_CTS_GET(info) ((info)->ioport[REG_STATUS] & E100_CTS_MASK)
-
-/* These are typically PA or PB and 0 means 0V, 1 means 3.3V */
-/* Is an output */
-#define E100_DTR_GET(info) ((*e100_modem_pins[(info)->line].dtr_shadow) & e100_modem_pins[(info)->line].dtr_mask)
-
-/* Normally inputs */
-#define E100_RI_GET(info) ((*e100_modem_pins[(info)->line].ri_port) & e100_modem_pins[(info)->line].ri_mask)
-#define E100_CD_GET(info) ((*e100_modem_pins[(info)->line].cd_port) & e100_modem_pins[(info)->line].cd_mask)
-
-/* Input */
-#define E100_DSR_GET(info) ((*e100_modem_pins[(info)->line].dsr_port) & e100_modem_pins[(info)->line].dsr_mask)
-
-/* Calculate the chartime depending on baudrate, numbor of bits etc. */
-static void update_char_time(struct e100_serial * info)
-{
-	tcflag_t cflags = info->port.tty->termios.c_cflag;
-	int bits;
-
-	/* calc. number of bits / data byte */
-	/* databits + startbit and 1 stopbit */
-	if ((cflags & CSIZE) == CS7)
-		bits = 9;
-	else
-		bits = 10;
-
-	if (cflags & CSTOPB)     /* 2 stopbits ? */
-		bits++;
-
-	if (cflags & PARENB)     /* parity bit ? */
-		bits++;
-
-	/* calc timeout */
-	info->char_time_usec = ((bits * 1000000) / info->baud) + 1;
-	info->flush_time_usec = 4*info->char_time_usec;
-	if (info->flush_time_usec < MIN_FLUSH_TIME_USEC)
-		info->flush_time_usec = MIN_FLUSH_TIME_USEC;
-
-}
-
-/*
- * This function maps from the Bxxxx defines in asm/termbits.h into real
- * baud rates.
- */
-
-static int
-cflag_to_baud(unsigned int cflag)
-{
-	static int baud_table[] = {
-		0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400,
-		4800, 9600, 19200, 38400 };
-
-	static int ext_baud_table[] = {
-		0, 57600, 115200, 230400, 460800, 921600, 1843200, 6250000,
-                0, 0, 0, 0, 0, 0, 0, 0 };
-
-	if (cflag & CBAUDEX)
-		return ext_baud_table[(cflag & CBAUD) & ~CBAUDEX];
-	else
-		return baud_table[cflag & CBAUD];
-}
-
-/* and this maps to an etrax100 hardware baud constant */
-
-static unsigned char
-cflag_to_etrax_baud(unsigned int cflag)
-{
-	char retval;
-
-	static char baud_table[] = {
-		-1, -1, -1, -1, -1, -1, -1, 0, 1, 2, -1, 3, 4, 5, 6, 7 };
-
-	static char ext_baud_table[] = {
-		-1, 8, 9, 10, 11, 12, 13, 14, -1, -1, -1, -1, -1, -1, -1, -1 };
-
-	if (cflag & CBAUDEX)
-		retval = ext_baud_table[(cflag & CBAUD) & ~CBAUDEX];
-	else
-		retval = baud_table[cflag & CBAUD];
-
-	if (retval < 0) {
-		printk(KERN_WARNING "serdriver tried setting invalid baud rate, flags %x.\n", cflag);
-		retval = 5; /* choose default 9600 instead */
-	}
-
-	return retval | (retval << 4); /* choose same for both TX and RX */
-}
-
-
-/* Various static support functions */
-
-/* Functions to set or clear DTR/RTS on the requested line */
-/* It is complicated by the fact that RTS is a serial port register, while
- * DTR might not be implemented in the HW at all, and if it is, it can be on
- * any general port.
- */
-
-
-static inline void
-e100_dtr(struct e100_serial *info, int set)
-{
-	unsigned char mask = e100_modem_pins[info->line].dtr_mask;
-
-#ifdef SERIAL_DEBUG_IO
-	printk("ser%i dtr %i mask: 0x%02X\n", info->line, set, mask);
-	printk("ser%i shadow before 0x%02X get: %i\n",
-	       info->line, *e100_modem_pins[info->line].dtr_shadow,
-	       E100_DTR_GET(info));
-#endif
-	/* DTR is active low */
-	{
-		unsigned long flags;
-
-		local_irq_save(flags);
-		*e100_modem_pins[info->line].dtr_shadow &= ~mask;
-		*e100_modem_pins[info->line].dtr_shadow |= (set ? 0 : mask);
-		*e100_modem_pins[info->line].dtr_port = *e100_modem_pins[info->line].dtr_shadow;
-		local_irq_restore(flags);
-	}
-
-#ifdef SERIAL_DEBUG_IO
-	printk("ser%i shadow after 0x%02X get: %i\n",
-	       info->line, *e100_modem_pins[info->line].dtr_shadow,
-	       E100_DTR_GET(info));
-#endif
-}
-
-/* set = 0 means 3.3V on the pin, bitvalue: 0=active, 1=inactive
- *                                          0=0V    , 1=3.3V
- */
-static inline void
-e100_rts(struct e100_serial *info, int set)
-{
-	unsigned long flags;
-	local_irq_save(flags);
-	info->rx_ctrl &= ~E100_RTS_MASK;
-	info->rx_ctrl |= (set ? 0 : E100_RTS_MASK);  /* RTS is active low */
-	info->ioport[REG_REC_CTRL] = info->rx_ctrl;
-	local_irq_restore(flags);
-#ifdef SERIAL_DEBUG_IO
-	printk("ser%i rts %i\n", info->line, set);
-#endif
-}
-
-
-/* If this behaves as a modem, RI and CD is an output */
-static inline void
-e100_ri_out(struct e100_serial *info, int set)
-{
-	/* RI is active low */
-	{
-		unsigned char mask = e100_modem_pins[info->line].ri_mask;
-		unsigned long flags;
-
-		local_irq_save(flags);
-		*e100_modem_pins[info->line].ri_shadow &= ~mask;
-		*e100_modem_pins[info->line].ri_shadow |= (set ? 0 : mask);
-		*e100_modem_pins[info->line].ri_port = *e100_modem_pins[info->line].ri_shadow;
-		local_irq_restore(flags);
-	}
-}
-static inline void
-e100_cd_out(struct e100_serial *info, int set)
-{
-	/* CD is active low */
-	{
-		unsigned char mask = e100_modem_pins[info->line].cd_mask;
-		unsigned long flags;
-
-		local_irq_save(flags);
-		*e100_modem_pins[info->line].cd_shadow &= ~mask;
-		*e100_modem_pins[info->line].cd_shadow |= (set ? 0 : mask);
-		*e100_modem_pins[info->line].cd_port = *e100_modem_pins[info->line].cd_shadow;
-		local_irq_restore(flags);
-	}
-}
-
-static inline void
-e100_disable_rx(struct e100_serial *info)
-{
-	/* disable the receiver */
-	info->ioport[REG_REC_CTRL] =
-		(info->rx_ctrl &= ~IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
-}
-
-static inline void
-e100_enable_rx(struct e100_serial *info)
-{
-	/* enable the receiver */
-	info->ioport[REG_REC_CTRL] =
-		(info->rx_ctrl |= IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
-}
-
-/* the rx DMA uses both the dma_descr and the dma_eop interrupts */
-
-static inline void
-e100_disable_rxdma_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("rxdma_irq(%d): 0\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ disable_rxdma_irq %i\n", info->line));
-	*R_IRQ_MASK2_CLR = (info->irq << 2) | (info->irq << 3);
-}
-
-static inline void
-e100_enable_rxdma_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("rxdma_irq(%d): 1\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ enable_rxdma_irq %i\n", info->line));
-	*R_IRQ_MASK2_SET = (info->irq << 2) | (info->irq << 3);
-}
-
-/* the tx DMA uses only dma_descr interrupt */
-
-static void e100_disable_txdma_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("txdma_irq(%d): 0\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ disable_txdma_irq %i\n", info->line));
-	*R_IRQ_MASK2_CLR = info->irq;
-}
-
-static void e100_enable_txdma_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("txdma_irq(%d): 1\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ enable_txdma_irq %i\n", info->line));
-	*R_IRQ_MASK2_SET = info->irq;
-}
-
-static void e100_disable_txdma_channel(struct e100_serial *info)
-{
-	unsigned long flags;
-
-	/* Disable output DMA channel for the serial port in question
-	 * ( set to something other than serialX)
-	 */
-	local_irq_save(flags);
-	DFLOW(DEBUG_LOG(info->line, "disable_txdma_channel %i\n", info->line));
-	if (info->line == 0) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma6)) ==
-		    IO_STATE(R_GEN_CONFIG, dma6, serial0)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma6);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, unused);
-		}
-	} else if (info->line == 1) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma8)) ==
-		    IO_STATE(R_GEN_CONFIG, dma8, serial1)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma8);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, usb);
-		}
-	} else if (info->line == 2) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma2)) ==
-		    IO_STATE(R_GEN_CONFIG, dma2, serial2)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma2);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, par0);
-		}
-	} else if (info->line == 3) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma4)) ==
-		    IO_STATE(R_GEN_CONFIG, dma4, serial3)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma4);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, par1);
-		}
-	}
-	*R_GEN_CONFIG = genconfig_shadow;
-	local_irq_restore(flags);
-}
-
-
-static void e100_enable_txdma_channel(struct e100_serial *info)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	DFLOW(DEBUG_LOG(info->line, "enable_txdma_channel %i\n", info->line));
-	/* Enable output DMA channel for the serial port in question */
-	if (info->line == 0) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma6);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, serial0);
-	} else if (info->line == 1) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma8);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, serial1);
-	} else if (info->line == 2) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma2);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, serial2);
-	} else if (info->line == 3) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma4);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, serial3);
-	}
-	*R_GEN_CONFIG = genconfig_shadow;
-	local_irq_restore(flags);
-}
-
-static void e100_disable_rxdma_channel(struct e100_serial *info)
-{
-	unsigned long flags;
-
-	/* Disable input DMA channel for the serial port in question
-	 * ( set to something other than serialX)
-	 */
-	local_irq_save(flags);
-	if (info->line == 0) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma7)) ==
-		    IO_STATE(R_GEN_CONFIG, dma7, serial0)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma7);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, unused);
-		}
-	} else if (info->line == 1) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma9)) ==
-		    IO_STATE(R_GEN_CONFIG, dma9, serial1)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma9);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, usb);
-		}
-	} else if (info->line == 2) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma3)) ==
-		    IO_STATE(R_GEN_CONFIG, dma3, serial2)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma3);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, par0);
-		}
-	} else if (info->line == 3) {
-		if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma5)) ==
-		    IO_STATE(R_GEN_CONFIG, dma5, serial3)) {
-			genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma5);
-			genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, par1);
-		}
-	}
-	*R_GEN_CONFIG = genconfig_shadow;
-	local_irq_restore(flags);
-}
-
-
-static void e100_enable_rxdma_channel(struct e100_serial *info)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	/* Enable input DMA channel for the serial port in question */
-	if (info->line == 0) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma7);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, serial0);
-	} else if (info->line == 1) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma9);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, serial1);
-	} else if (info->line == 2) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma3);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, serial2);
-	} else if (info->line == 3) {
-		genconfig_shadow &=  ~IO_MASK(R_GEN_CONFIG, dma5);
-		genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, serial3);
-	}
-	*R_GEN_CONFIG = genconfig_shadow;
-	local_irq_restore(flags);
-}
-
-#ifdef SERIAL_HANDLE_EARLY_ERRORS
-/* in order to detect and fix errors on the first byte
-   we have to use the serial interrupts as well. */
-
-static inline void
-e100_disable_serial_data_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("ser_irq(%d): 0\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ disable data_irq %i\n", info->line));
-	*R_IRQ_MASK1_CLR = (1U << (8+2*info->line));
-}
-
-static inline void
-e100_enable_serial_data_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("ser_irq(%d): 1\n",info->line);
-	printk("**** %d = %d\n",
-	       (8+2*info->line),
-	       (1U << (8+2*info->line)));
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ enable data_irq %i\n", info->line));
-	*R_IRQ_MASK1_SET = (1U << (8+2*info->line));
-}
-#endif
-
-static inline void
-e100_disable_serial_tx_ready_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("ser_tx_irq(%d): 0\n",info->line);
-#endif
-	DINTR1(DEBUG_LOG(info->line,"IRQ disable ready_irq %i\n", info->line));
-	*R_IRQ_MASK1_CLR = (1U << (8+1+2*info->line));
-}
-
-static inline void
-e100_enable_serial_tx_ready_irq(struct e100_serial *info)
-{
-#ifdef SERIAL_DEBUG_INTR
-	printk("ser_tx_irq(%d): 1\n",info->line);
-	printk("**** %d = %d\n",
-	       (8+1+2*info->line),
-	       (1U << (8+1+2*info->line)));
-#endif
-	DINTR2(DEBUG_LOG(info->line,"IRQ enable ready_irq %i\n", info->line));
-	*R_IRQ_MASK1_SET = (1U << (8+1+2*info->line));
-}
-
-static inline void e100_enable_rx_irq(struct e100_serial *info)
-{
-	if (info->uses_dma_in)
-		e100_enable_rxdma_irq(info);
-	else
-		e100_enable_serial_data_irq(info);
-}
-static inline void e100_disable_rx_irq(struct e100_serial *info)
-{
-	if (info->uses_dma_in)
-		e100_disable_rxdma_irq(info);
-	else
-		e100_disable_serial_data_irq(info);
-}
-
-#if defined(CONFIG_ETRAX_RS485)
-/* Enable RS-485 mode on selected port. This is UGLY. */
-static int
-e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
-{
-	struct e100_serial * info = (struct e100_serial *)tty->driver_data;
-
-#if defined(CONFIG_ETRAX_RS485_ON_PA)
-	*R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit);
-#endif
-
-	info->rs485 = *r;
-
-	/* Maximum delay before RTS equal to 1000 */
-	if (info->rs485.delay_rts_before_send >= 1000)
-		info->rs485.delay_rts_before_send = 1000;
-
-/*	printk("rts: on send = %i, after = %i, enabled = %i",
-		    info->rs485.rts_on_send,
-		    info->rs485.rts_after_sent,
-		    info->rs485.enabled
-	);
-*/
-	return 0;
-}
-
-static int
-e100_write_rs485(struct tty_struct *tty,
-                 const unsigned char *buf, int count)
-{
-	struct e100_serial * info = (struct e100_serial *)tty->driver_data;
-	int old_value = (info->rs485.flags) & SER_RS485_ENABLED;
-
-	/* rs485 is always implicitly enabled if we're using the ioctl()
-	 * but it doesn't have to be set in the serial_rs485
-	 * (to be backward compatible with old apps)
-	 * So we store, set and restore it.
-	 */
-	info->rs485.flags |= SER_RS485_ENABLED;
-	/* rs_write now deals with RS485 if enabled */
-	count = rs_write(tty, buf, count);
-	if (!old_value)
-		info->rs485.flags &= ~(SER_RS485_ENABLED);
-	return count;
-}
-
-#ifdef CONFIG_ETRAX_FAST_TIMER
-/* Timer function to toggle RTS when using FAST_TIMER */
-static void rs485_toggle_rts_timer_function(unsigned long data)
-{
-	struct e100_serial *info = (struct e100_serial *)data;
-
-	fast_timers_rs485[info->line].function = NULL;
-	e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
-#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
-	e100_enable_rx(info);
-	e100_enable_rx_irq(info);
-#endif
-}
-#endif
-#endif /* CONFIG_ETRAX_RS485 */
-
-/*
- * ------------------------------------------------------------
- * rs_stop() and rs_start()
- *
- * This routines are called before setting or resetting tty->stopped.
- * They enable or disable transmitter using the XOFF registers, as necessary.
- * ------------------------------------------------------------
- */
-
-static void
-rs_stop(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	if (info) {
-		unsigned long flags;
-		unsigned long xoff;
-
-		local_irq_save(flags);
-		DFLOW(DEBUG_LOG(info->line, "XOFF rs_stop xmit %i\n",
-				CIRC_CNT(info->xmit.head,
-					 info->xmit.tail,SERIAL_XMIT_SIZE)));
-
-		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char,
-				STOP_CHAR(info->port.tty));
-		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop);
-		if (I_IXON(tty))
-			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
-
-		*((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
-		local_irq_restore(flags);
-	}
-}
-
-static void
-rs_start(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	if (info) {
-		unsigned long flags;
-		unsigned long xoff;
-
-		local_irq_save(flags);
-		DFLOW(DEBUG_LOG(info->line, "XOFF rs_start xmit %i\n",
-				CIRC_CNT(info->xmit.head,
-					 info->xmit.tail,SERIAL_XMIT_SIZE)));
-		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty));
-		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
-		if (I_IXON(tty))
-			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
-
-		*((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
-		if (!info->uses_dma_out &&
-		    info->xmit.head != info->xmit.tail && info->xmit.buf)
-			e100_enable_serial_tx_ready_irq(info);
-
-		local_irq_restore(flags);
-	}
-}
-
-/*
- * ----------------------------------------------------------------------
- *
- * Here starts the interrupt handling routines.  All of the following
- * subroutines are declared as inline and are folded into
- * rs_interrupt().  They were separated out for readability's sake.
- *
- * Note: rs_interrupt() is a "fast" interrupt, which means that it
- * runs with interrupts turned off.  People who may want to modify
- * rs_interrupt() should try to keep the interrupt handler as fast as
- * possible.  After you are done making modifications, it is not a bad
- * idea to do:
- *
- * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
- *
- * and look at the resulting assemble code in serial.s.
- *
- * 				- Ted Ts'o (tytso@mit.edu), 7-Mar-93
- * -----------------------------------------------------------------------
- */
-
-/*
- * This routine is used by the interrupt handler to schedule
- * processing in the software interrupt portion of the driver.
- */
-static void rs_sched_event(struct e100_serial *info, int event)
-{
-	if (info->event & (1 << event))
-		return;
-	info->event |= 1 << event;
-	schedule_work(&info->work);
-}
-
-/* The output DMA channel is free - use it to send as many chars as possible
- * NOTES:
- *   We don't pay attention to info->x_char, which means if the TTY wants to
- *   use XON/XOFF it will set info->x_char but we won't send any X char!
- *
- *   To implement this, we'd just start a DMA send of 1 byte pointing at a
- *   buffer containing the X char, and skip updating xmit. We'd also have to
- *   check if the last sent char was the X char when we enter this function
- *   the next time, to avoid updating xmit with the sent X value.
- */
-
-static void
-transmit_chars_dma(struct e100_serial *info)
-{
-	unsigned int c, sentl;
-	struct etrax_dma_descr *descr;
-
-	/* acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */
-	*info->oclrintradr =
-		IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
-		IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
-
-#ifdef SERIAL_DEBUG_INTR
-	if (info->line == SERIAL_DEBUG_LINE)
-		printk("tc\n");
-#endif
-	if (!info->tr_running) {
-		/* weirdo... we shouldn't get here! */
-		printk(KERN_WARNING "Achtung: transmit_chars_dma with !tr_running\n");
-		return;
-	}
-
-	descr = &info->tr_descr;
-
-	/* first get the amount of bytes sent during the last DMA transfer,
-	   and update xmit accordingly */
-
-	/* if the stop bit was not set, all data has been sent */
-	if (!(descr->status & d_stop)) {
-		sentl = descr->sw_len;
-	} else
-		/* otherwise we find the amount of data sent here */
-		sentl = descr->hw_len;
-
-	DFLOW(DEBUG_LOG(info->line, "TX %i done\n", sentl));
-
-	/* update stats */
-	info->icount.tx += sentl;
-
-	/* update xmit buffer */
-	info->xmit.tail = (info->xmit.tail + sentl) & (SERIAL_XMIT_SIZE - 1);
-
-	/* if there is only a few chars left in the buf, wake up the blocked
-	   write if any */
-	if (CIRC_CNT(info->xmit.head,
-		     info->xmit.tail,
-		     SERIAL_XMIT_SIZE) < WAKEUP_CHARS)
-		rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
-
-	/* find out the largest amount of consecutive bytes we want to send now */
-
-	c = CIRC_CNT_TO_END(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
-
-	/* Don't send all in one DMA transfer - divide it so we wake up
-	 * application before all is sent
-	 */
-
-	if (c >= 4*WAKEUP_CHARS)
-		c = c/2;
-
-	if (c <= 0) {
-		/* our job here is done, don't schedule any new DMA transfer */
-		info->tr_running = 0;
-
-#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
-		if (info->rs485.flags & SER_RS485_ENABLED) {
-			/* Set a short timer to toggle RTS */
-			start_one_shot_timer(&fast_timers_rs485[info->line],
-			                     rs485_toggle_rts_timer_function,
-			                     (unsigned long)info,
-			                     info->char_time_usec*2,
-			                     "RS-485");
-		}
-#endif /* RS485 */
-		return;
-	}
-
-	/* ok we can schedule a dma send of c chars starting at info->xmit.tail */
-	/* set up the descriptor correctly for output */
-	DFLOW(DEBUG_LOG(info->line, "TX %i\n", c));
-	descr->ctrl = d_int | d_eol | d_wait; /* Wait needed for tty_wait_until_sent() */
-	descr->sw_len = c;
-	descr->buf = virt_to_phys(info->xmit.buf + info->xmit.tail);
-	descr->status = 0;
-
-	*info->ofirstadr = virt_to_phys(descr); /* write to R_DMAx_FIRST */
-	*info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start);
-
-	/* DMA is now running (hopefully) */
-} /* transmit_chars_dma */
-
-static void
-start_transmit(struct e100_serial *info)
-{
-#if 0
-	if (info->line == SERIAL_DEBUG_LINE)
-		printk("x\n");
-#endif
-
-	info->tr_descr.sw_len = 0;
-	info->tr_descr.hw_len = 0;
-	info->tr_descr.status = 0;
-	info->tr_running = 1;
-	if (info->uses_dma_out)
-		transmit_chars_dma(info);
-	else
-		e100_enable_serial_tx_ready_irq(info);
-} /* start_transmit */
-
-#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
-static int serial_fast_timer_started = 0;
-static int serial_fast_timer_expired = 0;
-static void flush_timeout_function(unsigned long data);
-#define START_FLUSH_FAST_TIMER_TIME(info, string, usec) {\
-  unsigned long timer_flags; \
-  local_irq_save(timer_flags); \
-  if (fast_timers[info->line].function == NULL) { \
-    serial_fast_timer_started++; \
-    TIMERD(DEBUG_LOG(info->line, "start_timer %i ", info->line)); \
-    TIMERD(DEBUG_LOG(info->line, "num started: %i\n", serial_fast_timer_started)); \
-    start_one_shot_timer(&fast_timers[info->line], \
-                         flush_timeout_function, \
-                         (unsigned long)info, \
-                         (usec), \
-                         string); \
-  } \
-  else { \
-    TIMERD(DEBUG_LOG(info->line, "timer %i already running\n", info->line)); \
-  } \
-  local_irq_restore(timer_flags); \
-}
-#define START_FLUSH_FAST_TIMER(info, string) START_FLUSH_FAST_TIMER_TIME(info, string, info->flush_time_usec)
-
-#else
-#define START_FLUSH_FAST_TIMER_TIME(info, string, usec)
-#define START_FLUSH_FAST_TIMER(info, string)
-#endif
-
-static struct etrax_recv_buffer *
-alloc_recv_buffer(unsigned int size)
-{
-	struct etrax_recv_buffer *buffer;
-
-	buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC);
-	if (!buffer)
-		return NULL;
-
-	buffer->next = NULL;
-	buffer->length = 0;
-	buffer->error = TTY_NORMAL;
-
-	return buffer;
-}
-
-static void
-append_recv_buffer(struct e100_serial *info, struct etrax_recv_buffer *buffer)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	if (!info->first_recv_buffer)
-		info->first_recv_buffer = buffer;
-	else
-		info->last_recv_buffer->next = buffer;
-
-	info->last_recv_buffer = buffer;
-
-	info->recv_cnt += buffer->length;
-	if (info->recv_cnt > info->max_recv_cnt)
-		info->max_recv_cnt = info->recv_cnt;
-
-	local_irq_restore(flags);
-}
-
-static int
-add_char_and_flag(struct e100_serial *info, unsigned char data, unsigned char flag)
-{
-	struct etrax_recv_buffer *buffer;
-	if (info->uses_dma_in) {
-		buffer = alloc_recv_buffer(4);
-		if (!buffer)
-			return 0;
-
-		buffer->length = 1;
-		buffer->error = flag;
-		buffer->buffer[0] = data;
-
-		append_recv_buffer(info, buffer);
-
-		info->icount.rx++;
-	} else {
-		tty_insert_flip_char(&info->port, data, flag);
-		info->icount.rx++;
-	}
-
-	return 1;
-}
-
-static unsigned int handle_descr_data(struct e100_serial *info,
-				      struct etrax_dma_descr *descr,
-				      unsigned int recvl)
-{
-	struct etrax_recv_buffer *buffer = phys_to_virt(descr->buf) - sizeof *buffer;
-
-	if (info->recv_cnt + recvl > 65536) {
-		printk(KERN_WARNING
-		       "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __func__, recvl);
-		return 0;
-	}
-
-	buffer->length = recvl;
-
-	if (info->errorcode == ERRCODE_SET_BREAK)
-		buffer->error = TTY_BREAK;
-	info->errorcode = 0;
-
-	append_recv_buffer(info, buffer);
-
-	buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE);
-	if (!buffer)
-		panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
-
-	descr->buf = virt_to_phys(buffer->buffer);
-
-	return recvl;
-}
-
-static unsigned int handle_all_descr_data(struct e100_serial *info)
-{
-	struct etrax_dma_descr *descr;
-	unsigned int recvl;
-	unsigned int ret = 0;
-
-	while (1)
-	{
-		descr = &info->rec_descr[info->cur_rec_descr];
-
-		if (descr == phys_to_virt(*info->idescradr))
-			break;
-
-		if (++info->cur_rec_descr == SERIAL_RECV_DESCRIPTORS)
-			info->cur_rec_descr = 0;
-
-		/* find out how many bytes were read */
-
-		/* if the eop bit was not set, all data has been received */
-		if (!(descr->status & d_eop)) {
-			recvl = descr->sw_len;
-		} else {
-			/* otherwise we find the amount of data received here */
-			recvl = descr->hw_len;
-		}
-
-		/* Reset the status information */
-		descr->status = 0;
-
-		DFLOW(  DEBUG_LOG(info->line, "RX %lu\n", recvl);
-			if (info->port.tty->stopped) {
-				unsigned char *buf = phys_to_virt(descr->buf);
-				DEBUG_LOG(info->line, "rx 0x%02X\n", buf[0]);
-				DEBUG_LOG(info->line, "rx 0x%02X\n", buf[1]);
-				DEBUG_LOG(info->line, "rx 0x%02X\n", buf[2]);
-			}
-			);
-
-		/* update stats */
-		info->icount.rx += recvl;
-
-		ret += handle_descr_data(info, descr, recvl);
-	}
-
-	return ret;
-}
-
-static void receive_chars_dma(struct e100_serial *info)
-{
-	struct tty_struct *tty;
-	unsigned char rstat;
-
-	/* Acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */
-	*info->iclrintradr =
-		IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
-		IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
-
-	tty = info->port.tty;
-	if (!tty) /* Something wrong... */
-		return;
-
-#ifdef SERIAL_HANDLE_EARLY_ERRORS
-	if (info->uses_dma_in)
-		e100_enable_serial_data_irq(info);
-#endif
-
-	if (info->errorcode == ERRCODE_INSERT_BREAK)
-		add_char_and_flag(info, '\0', TTY_BREAK);
-
-	handle_all_descr_data(info);
-
-	/* Read the status register to detect errors */
-	rstat = info->ioport[REG_STATUS];
-	if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
-		DFLOW(DEBUG_LOG(info->line, "XOFF detect stat %x\n", rstat));
-	}
-
-	if (rstat & SER_ERROR_MASK) {
-		/* If we got an error, we must reset it by reading the
-		 * data_in field
-		 */
-		unsigned char data = info->ioport[REG_DATA];
-
-		DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n",
-			  ((rstat & SER_ERROR_MASK) << 8) | data);
-
-		if (rstat & SER_PAR_ERR_MASK)
-			add_char_and_flag(info, data, TTY_PARITY);
-		else if (rstat & SER_OVERRUN_MASK)
-			add_char_and_flag(info, data, TTY_OVERRUN);
-		else if (rstat & SER_FRAMING_ERR_MASK)
-			add_char_and_flag(info, data, TTY_FRAME);
-	}
-
-	START_FLUSH_FAST_TIMER(info, "receive_chars");
-
-	/* Restart the receiving DMA */
-	*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
-}
-
-static int start_recv_dma(struct e100_serial *info)
-{
-	struct etrax_dma_descr *descr = info->rec_descr;
-	struct etrax_recv_buffer *buffer;
-        int i;
-
-	/* Set up the receiving descriptors */
-	for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) {
-		buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE);
-		if (!buffer)
-			panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
-
-		descr[i].ctrl = d_int;
-		descr[i].buf = virt_to_phys(buffer->buffer);
-		descr[i].sw_len = SERIAL_DESCR_BUF_SIZE;
-		descr[i].hw_len = 0;
-		descr[i].status = 0;
-		descr[i].next = virt_to_phys(&descr[i+1]);
-	}
-
-	/* Link the last descriptor to the first */
-	descr[i-1].next = virt_to_phys(&descr[0]);
-
-	/* Start with the first descriptor in the list */
-	info->cur_rec_descr = 0;
-
-	/* Start the DMA */
-	*info->ifirstadr = virt_to_phys(&descr[info->cur_rec_descr]);
-	*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start);
-
-	/* Input DMA should be running now */
-	return 1;
-}
-
-static void
-start_receive(struct e100_serial *info)
-{
-	if (info->uses_dma_in) {
-		/* reset the input dma channel to be sure it works */
-
-		*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
-		while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) ==
-		       IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
-
-		start_recv_dma(info);
-	}
-}
-
-
-/* the bits in the MASK2 register are laid out like this:
-   DMAI_EOP DMAI_DESCR DMAO_EOP DMAO_DESCR
-   where I is the input channel and O is the output channel for the port.
-   info->irq is the bit number for the DMAO_DESCR so to check the others we
-   shift info->irq to the left.
-*/
-
-/* dma output channel interrupt handler
-   this interrupt is called from DMA2(ser2), DMA4(ser3), DMA6(ser0) or
-   DMA8(ser1) when they have finished a descriptor with the intr flag set.
-*/
-
-static irqreturn_t
-tr_interrupt(int irq, void *dev_id)
-{
-	struct e100_serial *info;
-	unsigned long ireg;
-	int i;
-	int handled = 0;
-
-	/* find out the line that caused this irq and get it from rs_table */
-
-	ireg = *R_IRQ_MASK2_RD;  /* get the active irq bits for the dma channels */
-
-	for (i = 0; i < NR_PORTS; i++) {
-		info = rs_table + i;
-		if (!info->enabled || !info->uses_dma_out)
-			continue;
-		/* check for dma_descr (don't need to check for dma_eop in output dma for serial */
-		if (ireg & info->irq) {
-			handled = 1;
-			/* we can send a new dma bunch. make it so. */
-			DINTR2(DEBUG_LOG(info->line, "tr_interrupt %i\n", i));
-			/* Read jiffies_usec first,
-			 * we want this time to be as late as possible
-			 */
-			info->last_tx_active_usec = GET_JIFFIES_USEC();
-			info->last_tx_active = jiffies;
-			transmit_chars_dma(info);
-		}
-
-		/* FIXME: here we should really check for a change in the
-		   status lines and if so call status_handle(info) */
-	}
-	return IRQ_RETVAL(handled);
-} /* tr_interrupt */
-
-/* dma input channel interrupt handler */
-
-static irqreturn_t
-rec_interrupt(int irq, void *dev_id)
-{
-	struct e100_serial *info;
-	unsigned long ireg;
-	int i;
-	int handled = 0;
-
-	/* find out the line that caused this irq and get it from rs_table */
-
-	ireg = *R_IRQ_MASK2_RD;  /* get the active irq bits for the dma channels */
-
-	for (i = 0; i < NR_PORTS; i++) {
-		info = rs_table + i;
-		if (!info->enabled || !info->uses_dma_in)
-			continue;
-		/* check for both dma_eop and dma_descr for the input dma channel */
-		if (ireg & ((info->irq << 2) | (info->irq << 3))) {
-			handled = 1;
-			/* we have received something */
-			receive_chars_dma(info);
-		}
-
-		/* FIXME: here we should really check for a change in the
-		   status lines and if so call status_handle(info) */
-	}
-	return IRQ_RETVAL(handled);
-} /* rec_interrupt */
-
-static int force_eop_if_needed(struct e100_serial *info)
-{
-	/* We check data_avail bit to determine if data has
-	 * arrived since last time
-	 */
-	unsigned char rstat = info->ioport[REG_STATUS];
-
-	/* error or datavail? */
-	if (rstat & SER_ERROR_MASK) {
-		/* Some error has occurred. If there has been valid data, an
-		 * EOP interrupt will be made automatically. If no data, the
-		 * normal ser_interrupt should be enabled and handle it.
-		 * So do nothing!
-		 */
-		DEBUG_LOG(info->line, "timeout err: rstat 0x%03X\n",
-		          rstat | (info->line << 8));
-		return 0;
-	}
-
-	if (rstat & SER_DATA_AVAIL_MASK) {
-		/* Ok data, no error, count it */
-		TIMERD(DEBUG_LOG(info->line, "timeout: rstat 0x%03X\n",
-		          rstat | (info->line << 8)));
-		/* Read data to clear status flags */
-		(void)info->ioport[REG_DATA];
-
-		info->forced_eop = 0;
-		START_FLUSH_FAST_TIMER(info, "magic");
-		return 0;
-	}
-
-	/* hit the timeout, force an EOP for the input
-	 * dma channel if we haven't already
-	 */
-	if (!info->forced_eop) {
-		info->forced_eop = 1;
-		TIMERD(DEBUG_LOG(info->line, "timeout EOP %i\n", info->line));
-		FORCE_EOP(info);
-	}
-
-	return 1;
-}
-
-static void flush_to_flip_buffer(struct e100_serial *info)
-{
-	struct etrax_recv_buffer *buffer;
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	while ((buffer = info->first_recv_buffer) != NULL) {
-		unsigned int count = buffer->length;
-
-		tty_insert_flip_string(&info->port, buffer->buffer, count);
-		info->recv_cnt -= count;
-
-		if (count == buffer->length) {
-			info->first_recv_buffer = buffer->next;
-			kfree(buffer);
-		} else {
-			buffer->length -= count;
-			memmove(buffer->buffer, buffer->buffer + count, buffer->length);
-			buffer->error = TTY_NORMAL;
-		}
-	}
-
-	if (!info->first_recv_buffer)
-		info->last_recv_buffer = NULL;
-
-	local_irq_restore(flags);
-
-	/* This includes a check for low-latency */
-	tty_flip_buffer_push(&info->port);
-}
-
-static void check_flush_timeout(struct e100_serial *info)
-{
-	/* Flip what we've got (if we can) */
-	flush_to_flip_buffer(info);
-
-	/* We might need to flip later, but not to fast
-	 * since the system is busy processing input... */
-	if (info->first_recv_buffer)
-		START_FLUSH_FAST_TIMER_TIME(info, "flip", 2000);
-
-	/* Force eop last, since data might have come while we're processing
-	 * and if we started the slow timer above, we won't start a fast
-	 * below.
-	 */
-	force_eop_if_needed(info);
-}
-
-#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
-static void flush_timeout_function(unsigned long data)
-{
-	struct e100_serial *info = (struct e100_serial *)data;
-
-	fast_timers[info->line].function = NULL;
-	serial_fast_timer_expired++;
-	TIMERD(DEBUG_LOG(info->line, "flush_timeout %i ", info->line));
-	TIMERD(DEBUG_LOG(info->line, "num expired: %i\n", serial_fast_timer_expired));
-	check_flush_timeout(info);
-}
-
-#else
-
-/* dma fifo/buffer timeout handler
-   forces an end-of-packet for the dma input channel if no chars
-   have been received for CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS/100 s.
-*/
-
-static struct timer_list flush_timer;
-
-static void
-timed_flush_handler(struct timer_list *unused)
-{
-	struct e100_serial *info;
-	int i;
-
-	for (i = 0; i < NR_PORTS; i++) {
-		info = rs_table + i;
-		if (info->uses_dma_in)
-			check_flush_timeout(info);
-	}
-
-	/* restart flush timer */
-	mod_timer(&flush_timer, jiffies + CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS);
-}
-#endif
-
-#ifdef SERIAL_HANDLE_EARLY_ERRORS
-
-/* If there is an error (ie break) when the DMA is running and
- * there are no bytes in the fifo the DMA is stopped and we get no
- * eop interrupt. Thus we have to monitor the first bytes on a DMA
- * transfer, and if it is without error we can turn the serial
- * interrupts off.
- */
-
-/*
-BREAK handling on ETRAX 100:
-ETRAX will generate interrupt although there is no stop bit between the
-characters.
-
-Depending on how long the break sequence is, the end of the breaksequence
-will look differently:
-| indicates start/end of a character.
-
-B= Break character (0x00) with framing error.
-E= Error byte with parity error received after B characters.
-F= "Faked" valid byte received immediately after B characters.
-V= Valid byte
-
-1.
-    B          BL         ___________________________ V
-.._|__________|__________|                           |valid data |
-
-Multiple frame errors with data == 0x00 (B),
-the timing matches up "perfectly" so no extra ending char is detected.
-The RXD pin is 1 in the last interrupt, in that case
-we set info->errorcode = ERRCODE_INSERT_BREAK, but we can't really
-know if another byte will come and this really is case 2. below
-(e.g F=0xFF or 0xFE)
-If RXD pin is 0 we can expect another character (see 2. below).
-
-
-2.
-
-    B          B          E or F__________________..__ V
-.._|__________|__________|______    |                 |valid data
-                          "valid" or
-                          parity error
-
-Multiple frame errors with data == 0x00 (B),
-but the part of the break trigs is interpreted as a start bit (and possibly
-some 0 bits followed by a number of 1 bits and a stop bit).
-Depending on parity settings etc. this last character can be either
-a fake "valid" char (F) or have a parity error (E).
-
-If the character is valid it will be put in the buffer,
-we set info->errorcode = ERRCODE_SET_BREAK so the receive interrupt
-will set the flags so the tty will handle it,
-if it's an error byte it will not be put in the buffer
-and we set info->errorcode = ERRCODE_INSERT_BREAK.
-
-To distinguish a V byte in 1. from an F byte in 2. we keep a timestamp
-of the last faulty char (B) and compares it with the current time:
-If the time elapsed time is less then 2*char_time_usec we will assume
-it's a faked F char and not a Valid char and set
-info->errorcode = ERRCODE_SET_BREAK.
-
-Flaws in the above solution:
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-We use the timer to distinguish a F character from a V character,
-if a V character is to close after the break we might make the wrong decision.
-
-TODO: The break will be delayed until an F or V character is received.
-
-*/
-
-static void handle_ser_rx_interrupt_no_dma(struct e100_serial *info)
-{
-	unsigned long data_read;
-
-	/* Read data and status at the same time */
-	data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
-more_data:
-	if (data_read & IO_MASK(R_SERIAL0_READ, xoff_detect) ) {
-		DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
-	}
-	DINTR2(DEBUG_LOG(info->line, "ser_rx   %c\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read)));
-
-	if (data_read & ( IO_MASK(R_SERIAL0_READ, framing_err) |
-			  IO_MASK(R_SERIAL0_READ, par_err) |
-			  IO_MASK(R_SERIAL0_READ, overrun) )) {
-		/* An error */
-		info->last_rx_active_usec = GET_JIFFIES_USEC();
-		info->last_rx_active = jiffies;
-		DINTR1(DEBUG_LOG(info->line, "ser_rx err stat_data %04X\n", data_read));
-		DLOG_INT_TRIG(
-		if (!log_int_trig1_pos) {
-			log_int_trig1_pos = log_int_pos;
-			log_int(rdpc(), 0, 0);
-		}
-		);
-
-
-		if ( ((data_read & IO_MASK(R_SERIAL0_READ, data_in)) == 0) &&
-		     (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) ) {
-			/* Most likely a break, but we get interrupts over and
-			 * over again.
-			 */
-
-			if (!info->break_detected_cnt) {
-				DEBUG_LOG(info->line, "#BRK start\n", 0);
-			}
-			if (data_read & IO_MASK(R_SERIAL0_READ, rxd)) {
-				/* The RX pin is high now, so the break
-				 * must be over, but....
-				 * we can't really know if we will get another
-				 * last byte ending the break or not.
-				 * And we don't know if the byte (if any) will
-				 * have an error or look valid.
-				 */
-				DEBUG_LOG(info->line, "# BL BRK\n", 0);
-				info->errorcode = ERRCODE_INSERT_BREAK;
-			}
-			info->break_detected_cnt++;
-		} else {
-			/* The error does not look like a break, but could be
-			 * the end of one
-			 */
-			if (info->break_detected_cnt) {
-				DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt);
-				info->errorcode = ERRCODE_INSERT_BREAK;
-			} else {
-				unsigned char data = IO_EXTRACT(R_SERIAL0_READ,
-					data_in, data_read);
-				char flag = TTY_NORMAL;
-				if (info->errorcode == ERRCODE_INSERT_BREAK) {
-					tty_insert_flip_char(&info->port, 0, flag);
-					info->icount.rx++;
-				}
-
-				if (data_read & IO_MASK(R_SERIAL0_READ, par_err)) {
-					info->icount.parity++;
-					flag = TTY_PARITY;
-				} else if (data_read & IO_MASK(R_SERIAL0_READ, overrun)) {
-					info->icount.overrun++;
-					flag = TTY_OVERRUN;
-				} else if (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) {
-					info->icount.frame++;
-					flag = TTY_FRAME;
-				}
-				tty_insert_flip_char(&info->port, data, flag);
-				info->errorcode = 0;
-			}
-			info->break_detected_cnt = 0;
-		}
-	} else if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) {
-		/* No error */
-		DLOG_INT_TRIG(
-		if (!log_int_trig1_pos) {
-			if (log_int_pos >= log_int_size) {
-				log_int_pos = 0;
-			}
-			log_int_trig0_pos = log_int_pos;
-			log_int(rdpc(), 0, 0);
-		}
-		);
-		tty_insert_flip_char(&info->port,
-			IO_EXTRACT(R_SERIAL0_READ, data_in, data_read),
-			TTY_NORMAL);
-	} else {
-		DEBUG_LOG(info->line, "ser_rx int but no data_avail  %08lX\n", data_read);
-	}
-
-
-	info->icount.rx++;
-	data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
-	if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) {
-		DEBUG_LOG(info->line, "ser_rx   %c in loop\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read));
-		goto more_data;
-	}
-
-	tty_flip_buffer_push(&info->port);
-}
-
-static void handle_ser_rx_interrupt(struct e100_serial *info)
-{
-	unsigned char rstat;
-
-#ifdef SERIAL_DEBUG_INTR
-	printk("Interrupt from serport %d\n", i);
-#endif
-/*	DEBUG_LOG(info->line, "ser_interrupt stat %03X\n", rstat | (i << 8)); */
-	if (!info->uses_dma_in) {
-		handle_ser_rx_interrupt_no_dma(info);
-		return;
-	}
-	/* DMA is used */
-	rstat = info->ioport[REG_STATUS];
-	if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
-		DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
-	}
-
-	if (rstat & SER_ERROR_MASK) {
-		unsigned char data;
-
-		info->last_rx_active_usec = GET_JIFFIES_USEC();
-		info->last_rx_active = jiffies;
-		/* If we got an error, we must reset it by reading the
-		 * data_in field
-		 */
-		data = info->ioport[REG_DATA];
-		DINTR1(DEBUG_LOG(info->line, "ser_rx!  %c\n", data));
-		DINTR1(DEBUG_LOG(info->line, "ser_rx err stat %02X\n", rstat));
-		if (!data && (rstat & SER_FRAMING_ERR_MASK)) {
-			/* Most likely a break, but we get interrupts over and
-			 * over again.
-			 */
-
-			if (!info->break_detected_cnt) {
-				DEBUG_LOG(info->line, "#BRK start\n", 0);
-			}
-			if (rstat & SER_RXD_MASK) {
-				/* The RX pin is high now, so the break
-				 * must be over, but....
-				 * we can't really know if we will get another
-				 * last byte ending the break or not.
-				 * And we don't know if the byte (if any) will
-				 * have an error or look valid.
-				 */
-				DEBUG_LOG(info->line, "# BL BRK\n", 0);
-				info->errorcode = ERRCODE_INSERT_BREAK;
-			}
-			info->break_detected_cnt++;
-		} else {
-			/* The error does not look like a break, but could be
-			 * the end of one
-			 */
-			if (info->break_detected_cnt) {
-				DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt);
-				info->errorcode = ERRCODE_INSERT_BREAK;
-			} else {
-				if (info->errorcode == ERRCODE_INSERT_BREAK) {
-					info->icount.brk++;
-					add_char_and_flag(info, '\0', TTY_BREAK);
-				}
-
-				if (rstat & SER_PAR_ERR_MASK) {
-					info->icount.parity++;
-					add_char_and_flag(info, data, TTY_PARITY);
-				} else if (rstat & SER_OVERRUN_MASK) {
-					info->icount.overrun++;
-					add_char_and_flag(info, data, TTY_OVERRUN);
-				} else if (rstat & SER_FRAMING_ERR_MASK) {
-					info->icount.frame++;
-					add_char_and_flag(info, data, TTY_FRAME);
-				}
-
-				info->errorcode = 0;
-			}
-			info->break_detected_cnt = 0;
-			DEBUG_LOG(info->line, "#iERR s d %04X\n",
-			          ((rstat & SER_ERROR_MASK) << 8) | data);
-		}
-	} else { /* It was a valid byte, now let the DMA do the rest */
-		unsigned long curr_time_u = GET_JIFFIES_USEC();
-		unsigned long curr_time = jiffies;
-
-		if (info->break_detected_cnt) {
-			/* Detect if this character is a new valid char or the
-			 * last char in a break sequence: If LSBits are 0 and
-			 * MSBits are high AND the time is close to the
-			 * previous interrupt we should discard it.
-			 */
-			long elapsed_usec =
-			  (curr_time - info->last_rx_active) * (1000000/HZ) +
-			  curr_time_u - info->last_rx_active_usec;
-			if (elapsed_usec < 2*info->char_time_usec) {
-				DEBUG_LOG(info->line, "FBRK %i\n", info->line);
-				/* Report as BREAK (error) and let
-				 * receive_chars_dma() handle it
-				 */
-				info->errorcode = ERRCODE_SET_BREAK;
-			} else {
-				DEBUG_LOG(info->line, "Not end of BRK (V)%i\n", info->line);
-			}
-			DEBUG_LOG(info->line, "num brk %i\n", info->break_detected_cnt);
-		}
-
-#ifdef SERIAL_DEBUG_INTR
-		printk("** OK, disabling ser_interrupts\n");
-#endif
-		e100_disable_serial_data_irq(info);
-		DINTR2(DEBUG_LOG(info->line, "ser_rx OK %d\n", info->line));
-		info->break_detected_cnt = 0;
-
-	}
-	/* Restarting the DMA never hurts */
-	*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
-	START_FLUSH_FAST_TIMER(info, "ser_int");
-} /* handle_ser_rx_interrupt */
-
-static void handle_ser_tx_interrupt(struct e100_serial *info)
-{
-	unsigned long flags;
-
-	if (info->x_char) {
-		unsigned char rstat;
-		DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char));
-		local_irq_save(flags);
-		rstat = info->ioport[REG_STATUS];
-		DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
-
-		info->ioport[REG_TR_DATA] = info->x_char;
-		info->icount.tx++;
-		info->x_char = 0;
-		/* We must enable since it is disabled in ser_interrupt */
-		e100_enable_serial_tx_ready_irq(info);
-		local_irq_restore(flags);
-		return;
-	}
-	if (info->uses_dma_out) {
-		unsigned char rstat;
-		int i;
-		/* We only use normal tx interrupt when sending x_char */
-		DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0));
-		local_irq_save(flags);
-		rstat = info->ioport[REG_STATUS];
-		DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
-		e100_disable_serial_tx_ready_irq(info);
-		if (info->port.tty->stopped)
-			rs_stop(info->port.tty);
-		/* Enable the DMA channel and tell it to continue */
-		e100_enable_txdma_channel(info);
-		/* Wait 12 cycles before doing the DMA command */
-		for(i = 6;  i > 0; i--)
-			nop();
-
-		*info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, continue);
-		local_irq_restore(flags);
-		return;
-	}
-	/* Normal char-by-char interrupt */
-	if (info->xmit.head == info->xmit.tail
-	    || info->port.tty->stopped) {
-		DFLOW(DEBUG_LOG(info->line, "tx_int: stopped %i\n",
-				info->port.tty->stopped));
-		e100_disable_serial_tx_ready_irq(info);
-		info->tr_running = 0;
-		return;
-	}
-	DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail]));
-	/* Send a byte, rs485 timing is critical so turn of ints */
-	local_irq_save(flags);
-	info->ioport[REG_TR_DATA] = info->xmit.buf[info->xmit.tail];
-	info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1);
-	info->icount.tx++;
-	if (info->xmit.head == info->xmit.tail) {
-#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
-		if (info->rs485.flags & SER_RS485_ENABLED) {
-			/* Set a short timer to toggle RTS */
-			start_one_shot_timer(&fast_timers_rs485[info->line],
-			                     rs485_toggle_rts_timer_function,
-			                     (unsigned long)info,
-			                     info->char_time_usec*2,
-			                     "RS-485");
-		}
-#endif /* RS485 */
-		info->last_tx_active_usec = GET_JIFFIES_USEC();
-		info->last_tx_active = jiffies;
-		e100_disable_serial_tx_ready_irq(info);
-		info->tr_running = 0;
-		DFLOW(DEBUG_LOG(info->line, "tx_int: stop2\n", 0));
-	} else {
-		/* We must enable since it is disabled in ser_interrupt */
-		e100_enable_serial_tx_ready_irq(info);
-	}
-	local_irq_restore(flags);
-
-	if (CIRC_CNT(info->xmit.head,
-		     info->xmit.tail,
-		     SERIAL_XMIT_SIZE) < WAKEUP_CHARS)
-		rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
-
-} /* handle_ser_tx_interrupt */
-
-/* result of time measurements:
- * RX duration 54-60 us when doing something, otherwise 6-9 us
- * ser_int duration: just sending: 8-15 us normally, up to 73 us
- */
-static irqreturn_t
-ser_interrupt(int irq, void *dev_id)
-{
-	static volatile int tx_started = 0;
-	struct e100_serial *info;
-	int i;
-	unsigned long flags;
-	unsigned long irq_mask1_rd;
-	unsigned long data_mask = (1 << (8+2*0)); /* ser0 data_avail */
-	int handled = 0;
-	static volatile unsigned long reentered_ready_mask = 0;
-
-	local_irq_save(flags);
-	irq_mask1_rd = *R_IRQ_MASK1_RD;
-	/* First handle all rx interrupts with ints disabled */
-	info = rs_table;
-	irq_mask1_rd &= e100_ser_int_mask;
-	for (i = 0; i < NR_PORTS; i++) {
-		/* Which line caused the data irq? */
-		if (irq_mask1_rd & data_mask) {
-			handled = 1;
-			handle_ser_rx_interrupt(info);
-		}
-		info += 1;
-		data_mask <<= 2;
-	}
-	/* Handle tx interrupts with interrupts enabled so we
-	 * can take care of new data interrupts while transmitting
-	 * We protect the tx part with the tx_started flag.
-	 * We disable the tr_ready interrupts we are about to handle and
-	 * unblock the serial interrupt so new serial interrupts may come.
-	 *
-	 * If we get a new interrupt:
-	 *  - it migth be due to synchronous serial ports.
-	 *  - serial irq will be blocked by general irq handler.
-	 *  - async data will be handled above (sync will be ignored).
-	 *  - tx_started flag will prevent us from trying to send again and
-	 *    we will exit fast - no need to unblock serial irq.
-	 *  - Next (sync) serial interrupt handler will be runned with
-	 *    disabled interrupt due to restore_flags() at end of function,
-	 *    so sync handler will not be preempted or reentered.
-	 */
-	if (!tx_started) {
-		unsigned long ready_mask;
-		unsigned long
-		tx_started = 1;
-		/* Only the tr_ready interrupts left */
-		irq_mask1_rd &= (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) |
-				 IO_MASK(R_IRQ_MASK1_RD, ser1_ready) |
-				 IO_MASK(R_IRQ_MASK1_RD, ser2_ready) |
-				 IO_MASK(R_IRQ_MASK1_RD, ser3_ready));
-		while (irq_mask1_rd) {
-			/* Disable those we are about to handle */
-			*R_IRQ_MASK1_CLR = irq_mask1_rd;
-			/* Unblock the serial interrupt */
-			*R_VECT_MASK_SET = IO_STATE(R_VECT_MASK_SET, serial, set);
-
-			local_irq_enable();
-			ready_mask = (1 << (8+1+2*0)); /* ser0 tr_ready */
-			info = rs_table;
-			for (i = 0; i < NR_PORTS; i++) {
-				/* Which line caused the ready irq? */
-				if (irq_mask1_rd & ready_mask) {
-					handled = 1;
-					handle_ser_tx_interrupt(info);
-				}
-				info += 1;
-				ready_mask <<= 2;
-			}
-			/* handle_ser_tx_interrupt enables tr_ready interrupts */
-			local_irq_disable();
-			/* Handle reentered TX interrupt */
-			irq_mask1_rd = reentered_ready_mask;
-		}
-		local_irq_disable();
-		tx_started = 0;
-	} else {
-		unsigned long ready_mask;
-		ready_mask = irq_mask1_rd & (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) |
-					     IO_MASK(R_IRQ_MASK1_RD, ser1_ready) |
-					     IO_MASK(R_IRQ_MASK1_RD, ser2_ready) |
-					     IO_MASK(R_IRQ_MASK1_RD, ser3_ready));
-		if (ready_mask) {
-			reentered_ready_mask |= ready_mask;
-			/* Disable those we are about to handle */
-			*R_IRQ_MASK1_CLR = ready_mask;
-			DFLOW(DEBUG_LOG(SERIAL_DEBUG_LINE, "ser_int reentered with TX %X\n", ready_mask));
-		}
-	}
-
-	local_irq_restore(flags);
-	return IRQ_RETVAL(handled);
-} /* ser_interrupt */
-#endif
-
-/*
- * -------------------------------------------------------------------
- * Here ends the serial interrupt routines.
- * -------------------------------------------------------------------
- */
-
-/*
- * This routine is used to handle the "bottom half" processing for the
- * serial driver, known also the "software interrupt" processing.
- * This processing is done at the kernel interrupt level, after the
- * rs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON.  This
- * is where time-consuming activities which can not be done in the
- * interrupt driver proper are done; the interrupt driver schedules
- * them using rs_sched_event(), and they get done here.
- */
-static void
-do_softint(struct work_struct *work)
-{
-	struct e100_serial	*info;
-	struct tty_struct	*tty;
-
-	info = container_of(work, struct e100_serial, work);
-
-	tty = info->port.tty;
-	if (!tty)
-		return;
-
-	if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
-		tty_wakeup(tty);
-}
-
-static int
-startup(struct e100_serial * info)
-{
-	unsigned long flags;
-	unsigned long xmit_page;
-	int i;
-
-	xmit_page = get_zeroed_page(GFP_KERNEL);
-	if (!xmit_page)
-		return -ENOMEM;
-
-	local_irq_save(flags);
-
-	/* if it was already initialized, skip this */
-
-	if (tty_port_initialized(&info->port)) {
-		local_irq_restore(flags);
-		free_page(xmit_page);
-		return 0;
-	}
-
-	if (info->xmit.buf)
-		free_page(xmit_page);
-	else
-		info->xmit.buf = (unsigned char *) xmit_page;
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("starting up ttyS%d (xmit_buf 0x%p)...\n", info->line, info->xmit.buf);
-#endif
-
-	/*
-	 * Clear the FIFO buffers and disable them
-	 * (they will be reenabled in change_speed())
-	 */
-
-	/*
-	 * Reset the DMA channels and make sure their interrupts are cleared
-	 */
-
-	if (info->dma_in_enabled) {
-		info->uses_dma_in = 1;
-		e100_enable_rxdma_channel(info);
-
-		*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
-
-		/* Wait until reset cycle is complete */
-		while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) ==
-		       IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
-
-		/* Make sure the irqs are cleared */
-		*info->iclrintradr =
-			IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
-			IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
-	} else {
-		e100_disable_rxdma_channel(info);
-	}
-
-	if (info->dma_out_enabled) {
-		info->uses_dma_out = 1;
-		e100_enable_txdma_channel(info);
-		*info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
-
-		while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) ==
-		       IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
-
-		/* Make sure the irqs are cleared */
-		*info->oclrintradr =
-			IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
-			IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
-	} else {
-		e100_disable_txdma_channel(info);
-	}
-
-	if (info->port.tty)
-		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
-
-	info->xmit.head = info->xmit.tail = 0;
-	info->first_recv_buffer = info->last_recv_buffer = NULL;
-	info->recv_cnt = info->max_recv_cnt = 0;
-
-	for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++)
-		info->rec_descr[i].buf = 0;
-
-	/*
-	 * and set the speed and other flags of the serial port
-	 * this will start the rx/tx as well
-	 */
-#ifdef SERIAL_HANDLE_EARLY_ERRORS
-	e100_enable_serial_data_irq(info);
-#endif
-	change_speed(info);
-
-	/* dummy read to reset any serial errors */
-
-	(void)info->ioport[REG_DATA];
-
-	/* enable the interrupts */
-	if (info->uses_dma_out)
-		e100_enable_txdma_irq(info);
-
-	e100_enable_rx_irq(info);
-
-	info->tr_running = 0; /* to be sure we don't lock up the transmitter */
-
-	/* setup the dma input descriptor and start dma */
-
-	start_receive(info);
-
-	/* for safety, make sure the descriptors last result is 0 bytes written */
-
-	info->tr_descr.sw_len = 0;
-	info->tr_descr.hw_len = 0;
-	info->tr_descr.status = 0;
-
-	/* enable RTS/DTR last */
-
-	e100_rts(info, 1);
-	e100_dtr(info, 1);
-
-	tty_port_set_initialized(&info->port, 1);
-
-	local_irq_restore(flags);
-	return 0;
-}
-
-/*
- * This routine will shutdown a serial port; interrupts are disabled, and
- * DTR is dropped if the hangup on close termio flag is on.
- */
-static void
-shutdown(struct e100_serial * info)
-{
-	unsigned long flags;
-	struct etrax_dma_descr *descr = info->rec_descr;
-	struct etrax_recv_buffer *buffer;
-	int i;
-
-	/* shut down the transmitter and receiver */
-	DFLOW(DEBUG_LOG(info->line, "shutdown %i\n", info->line));
-	e100_disable_rx(info);
-	info->ioport[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40);
-
-	/* disable interrupts, reset dma channels */
-	if (info->uses_dma_in) {
-		e100_disable_rxdma_irq(info);
-		*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
-		info->uses_dma_in = 0;
-	} else {
-		e100_disable_serial_data_irq(info);
-	}
-
-	if (info->uses_dma_out) {
-		e100_disable_txdma_irq(info);
-		info->tr_running = 0;
-		*info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
-		info->uses_dma_out = 0;
-	} else {
-		e100_disable_serial_tx_ready_irq(info);
-		info->tr_running = 0;
-	}
-
-	if (!tty_port_initialized(&info->port))
-		return;
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("Shutting down serial port %d (irq %d)....\n", info->line,
-	       info->irq);
-#endif
-
-	local_irq_save(flags);
-
-	if (info->xmit.buf) {
-		free_page((unsigned long)info->xmit.buf);
-		info->xmit.buf = NULL;
-	}
-
-	for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++)
-		if (descr[i].buf) {
-			buffer = phys_to_virt(descr[i].buf) - sizeof *buffer;
-			kfree(buffer);
-			descr[i].buf = 0;
-		}
-
-	if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
-		/* hang up DTR and RTS if HUPCL is enabled */
-		e100_dtr(info, 0);
-		e100_rts(info, 0); /* could check CRTSCTS before doing this */
-	}
-
-	if (info->port.tty)
-		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
-
-	tty_port_set_initialized(&info->port, 0);
-	local_irq_restore(flags);
-}
-
-
-/* change baud rate and other assorted parameters */
-
-static void
-change_speed(struct e100_serial *info)
-{
-	unsigned int cflag;
-	unsigned long xoff;
-	unsigned long flags;
-	/* first some safety checks */
-
-	if (!info->port.tty)
-		return;
-	if (!info->ioport)
-		return;
-
-	cflag = info->port.tty->termios.c_cflag;
-
-	/* possibly, the tx/rx should be disabled first to do this safely */
-
-	/* change baud-rate and write it to the hardware */
-	if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) {
-		/* Special baudrate */
-		u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */
-		unsigned long alt_source =
-				IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) |
-				IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal);
-		/* R_ALT_SER_BAUDRATE selects the source */
-		DBAUD(printk("Custom baudrate: baud_base/divisor %lu/%i\n",
-		       (unsigned long)info->baud_base, info->custom_divisor));
-		if (info->baud_base == SERIAL_PRESCALE_BASE) {
-			/* 0, 2-65535 (0=65536) */
-			u16 divisor = info->custom_divisor;
-			/* R_SERIAL_PRESCALE (upper 16 bits of R_CLOCK_PRESCALE) */
-			/* baudrate is 3.125MHz/custom_divisor */
-			alt_source =
-				IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, prescale) |
-				IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, prescale);
-			alt_source = 0x11;
-			DBAUD(printk("Writing SERIAL_PRESCALE: divisor %i\n", divisor));
-			*R_SERIAL_PRESCALE = divisor;
-			info->baud = SERIAL_PRESCALE_BASE/divisor;
-		}
-		else
-		{
-			/* Bad baudbase, we don't support using timer0
-			 * for baudrate.
-			 */
-			printk(KERN_WARNING "Bad baud_base/custom_divisor: %lu/%i\n",
-			       (unsigned long)info->baud_base, info->custom_divisor);
-		}
-		r_alt_ser_baudrate_shadow &= ~mask;
-		r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8));
-		*R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow;
-	} else {
-		/* Normal baudrate */
-		/* Make sure we use normal baudrate */
-		u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */
-		unsigned long alt_source =
-			IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) |
-			IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal);
-		r_alt_ser_baudrate_shadow &= ~mask;
-		r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8));
-		*R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow;
-
-		info->baud = cflag_to_baud(cflag);
-		info->ioport[REG_BAUD] = cflag_to_etrax_baud(cflag);
-	}
-
-	/* start with default settings and then fill in changes */
-	local_irq_save(flags);
-	/* 8 bit, no/even parity */
-	info->rx_ctrl &= ~(IO_MASK(R_SERIAL0_REC_CTRL, rec_bitnr) |
-			   IO_MASK(R_SERIAL0_REC_CTRL, rec_par_en) |
-			   IO_MASK(R_SERIAL0_REC_CTRL, rec_par));
-
-	/* 8 bit, no/even parity, 1 stop bit, no cts */
-	info->tx_ctrl &= ~(IO_MASK(R_SERIAL0_TR_CTRL, tr_bitnr) |
-			   IO_MASK(R_SERIAL0_TR_CTRL, tr_par_en) |
-			   IO_MASK(R_SERIAL0_TR_CTRL, tr_par) |
-			   IO_MASK(R_SERIAL0_TR_CTRL, stop_bits) |
-			   IO_MASK(R_SERIAL0_TR_CTRL, auto_cts));
-
-	if ((cflag & CSIZE) == CS7) {
-		/* set 7 bit mode */
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_bitnr, tr_7bit);
-		info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_bitnr, rec_7bit);
-	}
-
-	if (cflag & CSTOPB) {
-		/* set 2 stop bit mode */
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, stop_bits, two_bits);
-	}
-
-	if (cflag & PARENB) {
-		/* enable parity */
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par_en, enable);
-		info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par_en, enable);
-	}
-
-	if (cflag & CMSPAR) {
-		/* enable stick parity, PARODD mean Mark which matches ETRAX */
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_stick_par, stick);
-		info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_stick_par, stick);
-	}
-	if (cflag & PARODD) {
-		/* set odd parity (or Mark if CMSPAR) */
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par, odd);
-		info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par, odd);
-	}
-
-	if (cflag & CRTSCTS) {
-		/* enable automatic CTS handling */
-		DFLOW(DEBUG_LOG(info->line, "FLOW auto_cts enabled\n", 0));
-		info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, auto_cts, active);
-	}
-
-	/* make sure the tx and rx are enabled */
-
-	info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_enable, enable);
-	info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_enable, enable);
-
-	/* actually write the control regs to the hardware */
-
-	info->ioport[REG_TR_CTRL] = info->tx_ctrl;
-	info->ioport[REG_REC_CTRL] = info->rx_ctrl;
-	xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty));
-	xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
-	if (info->port.tty->termios.c_iflag & IXON ) {
-		DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n",
-				STOP_CHAR(info->port.tty)));
-		xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
-	}
-
-	*((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
-	local_irq_restore(flags);
-
-	update_char_time(info);
-
-} /* change_speed */
-
-/* start transmitting chars NOW */
-
-static void
-rs_flush_chars(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	if (info->tr_running ||
-	    info->xmit.head == info->xmit.tail ||
-	    tty->stopped ||
-	    !info->xmit.buf)
-		return;
-
-#ifdef SERIAL_DEBUG_FLOW
-	printk("rs_flush_chars\n");
-#endif
-
-	/* this protection might not exactly be necessary here */
-
-	local_irq_save(flags);
-	start_transmit(info);
-	local_irq_restore(flags);
-}
-
-static int rs_raw_write(struct tty_struct *tty,
-			const unsigned char *buf, int count)
-{
-	int	c, ret = 0;
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	/* first some sanity checks */
-
-	if (!info->xmit.buf)
-		return 0;
-
-#ifdef SERIAL_DEBUG_DATA
-	if (info->line == SERIAL_DEBUG_LINE)
-		printk("rs_raw_write (%d), status %d\n",
-		       count, info->ioport[REG_STATUS]);
-#endif
-
-	local_save_flags(flags);
-	DFLOW(DEBUG_LOG(info->line, "write count %i ", count));
-	DFLOW(DEBUG_LOG(info->line, "ldisc\n"));
-
-
-	/* The local_irq_disable/restore_flags pairs below are needed
-	 * because the DMA interrupt handler moves the info->xmit values.
-	 * the memcpy needs to be in the critical region unfortunately,
-	 * because we need to read xmit values, memcpy, write xmit values
-	 * in one atomic operation... this could perhaps be avoided by
-	 * more clever design.
-	 */
-	local_irq_disable();
-		while (count) {
-			c = CIRC_SPACE_TO_END(info->xmit.head,
-					      info->xmit.tail,
-					      SERIAL_XMIT_SIZE);
-
-			if (count < c)
-				c = count;
-			if (c <= 0)
-				break;
-
-			memcpy(info->xmit.buf + info->xmit.head, buf, c);
-			info->xmit.head = (info->xmit.head + c) &
-				(SERIAL_XMIT_SIZE-1);
-			buf += c;
-			count -= c;
-			ret += c;
-		}
-	local_irq_restore(flags);
-
-	/* enable transmitter if not running, unless the tty is stopped
-	 * this does not need IRQ protection since if tr_running == 0
-	 * the IRQ's are not running anyway for this port.
-	 */
-	DFLOW(DEBUG_LOG(info->line, "write ret %i\n", ret));
-
-	if (info->xmit.head != info->xmit.tail &&
-	    !tty->stopped &&
-	    !info->tr_running) {
-		start_transmit(info);
-	}
-
-	return ret;
-} /* raw_raw_write() */
-
-static int
-rs_write(struct tty_struct *tty,
-	 const unsigned char *buf, int count)
-{
-#if defined(CONFIG_ETRAX_RS485)
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-
-	if (info->rs485.flags & SER_RS485_ENABLED)
-	{
-		/* If we are in RS-485 mode, we need to toggle RTS and disable
-		 * the receiver before initiating a DMA transfer
-		 */
-#ifdef CONFIG_ETRAX_FAST_TIMER
-		/* Abort any started timer */
-		fast_timers_rs485[info->line].function = NULL;
-		del_fast_timer(&fast_timers_rs485[info->line]);
-#endif
-		e100_rts(info, (info->rs485.flags & SER_RS485_RTS_ON_SEND));
-#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
-		e100_disable_rx(info);
-		e100_enable_rx_irq(info);
-#endif
-		if (info->rs485.delay_rts_before_send > 0)
-			msleep(info->rs485.delay_rts_before_send);
-	}
-#endif /* CONFIG_ETRAX_RS485 */
-
-	count = rs_raw_write(tty, buf, count);
-
-#if defined(CONFIG_ETRAX_RS485)
-	if (info->rs485.flags & SER_RS485_ENABLED)
-	{
-		unsigned int val;
-		/* If we are in RS-485 mode the following has to be done:
-		 * wait until DMA is ready
-		 * wait on transmit shift register
-		 * toggle RTS
-		 * enable the receiver
-		 */
-
-		/* Sleep until all sent */
-		tty_wait_until_sent(tty, 0);
-#ifdef CONFIG_ETRAX_FAST_TIMER
-		/* Now sleep a little more so that shift register is empty */
-		schedule_usleep(info->char_time_usec * 2);
-#endif
-		/* wait on transmit shift register */
-		do{
-			get_lsr_info(info, &val);
-		}while (!(val & TIOCSER_TEMT));
-
-		e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
-
-#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
-		e100_enable_rx(info);
-		e100_enable_rxdma_irq(info);
-#endif
-	}
-#endif /* CONFIG_ETRAX_RS485 */
-
-	return count;
-} /* rs_write */
-
-
-/* how much space is available in the xmit buffer? */
-
-static int
-rs_write_room(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-
-	return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
-}
-
-/* How many chars are in the xmit buffer?
- * This does not include any chars in the transmitter FIFO.
- * Use wait_until_sent for waiting for FIFO drain.
- */
-
-static int
-rs_chars_in_buffer(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-
-	return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
-}
-
-/* discard everything in the xmit buffer */
-
-static void
-rs_flush_buffer(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	local_irq_save(flags);
-	info->xmit.head = info->xmit.tail = 0;
-	local_irq_restore(flags);
-
-	tty_wakeup(tty);
-}
-
-/*
- * This function is used to send a high-priority XON/XOFF character to
- * the device
- *
- * Since we use DMA we don't check for info->x_char in transmit_chars_dma(),
- * but we do it in handle_ser_tx_interrupt().
- * We disable DMA channel and enable tx ready interrupt and write the
- * character when possible.
- */
-static void rs_send_xchar(struct tty_struct *tty, char ch)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-	local_irq_save(flags);
-	if (info->uses_dma_out) {
-		/* Put the DMA on hold and disable the channel */
-		*info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, hold);
-		while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) !=
-		       IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, hold));
-		e100_disable_txdma_channel(info);
-	}
-
-	/* Must make sure transmitter is not stopped before we can transmit */
-	if (tty->stopped)
-		rs_start(tty);
-
-	/* Enable manual transmit interrupt and send from there */
-	DFLOW(DEBUG_LOG(info->line, "rs_send_xchar 0x%02X\n", ch));
-	info->x_char = ch;
-	e100_enable_serial_tx_ready_irq(info);
-	local_irq_restore(flags);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_throttle()
- *
- * This routine is called by the upper-layer tty layer to signal that
- * incoming characters should be throttled.
- * ------------------------------------------------------------
- */
-static void
-rs_throttle(struct tty_struct * tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-#ifdef SERIAL_DEBUG_THROTTLE
-	printk("throttle %s ....\n", tty_name(tty));
-#endif
-	DFLOW(DEBUG_LOG(info->line,"rs_throttle\n"));
-
-	/* Do RTS before XOFF since XOFF might take some time */
-	if (C_CRTSCTS(tty)) {
-		/* Turn off RTS line */
-		e100_rts(info, 0);
-	}
-	if (I_IXOFF(tty))
-		rs_send_xchar(tty, STOP_CHAR(tty));
-
-}
-
-static void
-rs_unthrottle(struct tty_struct * tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-#ifdef SERIAL_DEBUG_THROTTLE
-	printk("unthrottle %s ....\n", tty_name(tty));
-#endif
-	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc\n"));
-	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count));
-	/* Do RTS before XOFF since XOFF might take some time */
-	if (C_CRTSCTS(tty)) {
-		/* Assert RTS line  */
-		e100_rts(info, 1);
-	}
-
-	if (I_IXOFF(tty)) {
-		if (info->x_char)
-			info->x_char = 0;
-		else
-			rs_send_xchar(tty, START_CHAR(tty));
-	}
-
-}
-
-/*
- * ------------------------------------------------------------
- * rs_ioctl() and friends
- * ------------------------------------------------------------
- */
-
-static int
-get_serial_info(struct e100_serial * info,
-		struct serial_struct * retinfo)
-{
-	struct serial_struct tmp;
-
-	/* this is all probably wrong, there are a lot of fields
-	 * here that we don't have in e100_serial and maybe we
-	 * should set them to something else than 0.
-	 */
-
-	memset(&tmp, 0, sizeof(tmp));
-	tmp.type = info->type;
-	tmp.line = info->line;
-	tmp.port = (int)info->ioport;
-	tmp.irq = info->irq;
-	tmp.flags = info->port.flags;
-	tmp.baud_base = info->baud_base;
-	tmp.close_delay = info->port.close_delay;
-	tmp.closing_wait = info->port.closing_wait;
-	tmp.custom_divisor = info->custom_divisor;
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return -EFAULT;
-	return 0;
-}
-
-static int
-set_serial_info(struct e100_serial *info,
-		struct serial_struct *new_info)
-{
-	struct serial_struct new_serial;
-	struct e100_serial old_info;
-	int retval = 0;
-
-	if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
-		return -EFAULT;
-
-	old_info = *info;
-
-	if (!capable(CAP_SYS_ADMIN)) {
-		if ((new_serial.type != info->type) ||
-		    (new_serial.close_delay != info->port.close_delay) ||
-		    ((new_serial.flags & ~ASYNC_USR_MASK) !=
-		     (info->port.flags & ~ASYNC_USR_MASK)))
-			return -EPERM;
-		info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
-			       (new_serial.flags & ASYNC_USR_MASK));
-		goto check_and_exit;
-	}
-
-	if (info->port.count > 1)
-		return -EBUSY;
-
-	/*
-	 * OK, past this point, all the error checking has been done.
-	 * At this point, we start making changes.....
-	 */
-
-	info->baud_base = new_serial.baud_base;
-	info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) |
-		       (new_serial.flags & ASYNC_FLAGS));
-	info->custom_divisor = new_serial.custom_divisor;
-	info->type = new_serial.type;
-	info->port.close_delay = new_serial.close_delay;
-	info->port.closing_wait = new_serial.closing_wait;
-	info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
-
- check_and_exit:
-	if (tty_port_initialized(&info->port))
-		change_speed(info);
-	else
-		retval = startup(info);
-	return retval;
-}
-
-/*
- * get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- * 	    is emptied.  On bus types like RS485, the transmitter must
- * 	    release the bus after transmitting. This must be done when
- * 	    the transmit shift register is empty, not be done when the
- * 	    transmit holding register is empty.  This functionality
- * 	    allows an RS485 driver to be written in user space.
- */
-static int
-get_lsr_info(struct e100_serial * info, unsigned int *value)
-{
-	unsigned int result = TIOCSER_TEMT;
-	unsigned long curr_time = jiffies;
-	unsigned long curr_time_usec = GET_JIFFIES_USEC();
-	unsigned long elapsed_usec =
-		(curr_time - info->last_tx_active) * 1000000/HZ +
-		curr_time_usec - info->last_tx_active_usec;
-
-	if (info->xmit.head != info->xmit.tail ||
-	    elapsed_usec < 2*info->char_time_usec) {
-		result = 0;
-	}
-
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-	return 0;
-}
-
-#ifdef SERIAL_DEBUG_IO
-struct state_str
-{
-	int state;
-	const char *str;
-};
-
-const struct state_str control_state_str[] = {
-	{TIOCM_DTR, "DTR" },
-	{TIOCM_RTS, "RTS"},
-	{TIOCM_ST, "ST?" },
-	{TIOCM_SR, "SR?" },
-	{TIOCM_CTS, "CTS" },
-	{TIOCM_CD, "CD" },
-	{TIOCM_RI, "RI" },
-	{TIOCM_DSR, "DSR" },
-	{0, NULL }
-};
-
-char *get_control_state_str(int MLines, char *s)
-{
-	int i = 0;
-
-	s[0]='\0';
-	while (control_state_str[i].str != NULL) {
-		if (MLines & control_state_str[i].state) {
-			if (s[0] != '\0') {
-				strcat(s, ", ");
-			}
-			strcat(s, control_state_str[i].str);
-		}
-		i++;
-	}
-	return s;
-}
-#endif
-
-static int
-rs_break(struct tty_struct *tty, int break_state)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	if (!info->ioport)
-		return -EIO;
-
-	local_irq_save(flags);
-	if (break_state == -1) {
-		/* Go to manual mode and set the txd pin to 0 */
-		/* Clear bit 7 (txd) and 6 (tr_enable) */
-		info->tx_ctrl &= 0x3F;
-	} else {
-		/* Set bit 7 (txd) and 6 (tr_enable) */
-		info->tx_ctrl |= (0x80 | 0x40);
-	}
-	info->ioport[REG_TR_CTRL] = info->tx_ctrl;
-	local_irq_restore(flags);
-	return 0;
-}
-
-static int
-rs_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	if (clear & TIOCM_RTS)
-		e100_rts(info, 0);
-	if (clear & TIOCM_DTR)
-		e100_dtr(info, 0);
-	/* Handle FEMALE behaviour */
-	if (clear & TIOCM_RI)
-		e100_ri_out(info, 0);
-	if (clear & TIOCM_CD)
-		e100_cd_out(info, 0);
-
-	if (set & TIOCM_RTS)
-		e100_rts(info, 1);
-	if (set & TIOCM_DTR)
-		e100_dtr(info, 1);
-	/* Handle FEMALE behaviour */
-	if (set & TIOCM_RI)
-		e100_ri_out(info, 1);
-	if (set & TIOCM_CD)
-		e100_cd_out(info, 1);
-
-	local_irq_restore(flags);
-	return 0;
-}
-
-static int
-rs_tiocmget(struct tty_struct *tty)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned int result;
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	result =
-		(!E100_RTS_GET(info) ? TIOCM_RTS : 0)
-		| (!E100_DTR_GET(info) ? TIOCM_DTR : 0)
-		| (!E100_RI_GET(info) ? TIOCM_RNG : 0)
-		| (!E100_DSR_GET(info) ? TIOCM_DSR : 0)
-		| (!E100_CD_GET(info) ? TIOCM_CAR : 0)
-		| (!E100_CTS_GET(info) ? TIOCM_CTS : 0);
-
-	local_irq_restore(flags);
-
-#ifdef SERIAL_DEBUG_IO
-	printk(KERN_DEBUG "ser%i: modem state: %i 0x%08X\n",
-		info->line, result, result);
-	{
-		char s[100];
-
-		get_control_state_str(result, s);
-		printk(KERN_DEBUG "state: %s\n", s);
-	}
-#endif
-	return result;
-
-}
-
-
-static int
-rs_ioctl(struct tty_struct *tty,
-	 unsigned int cmd, unsigned long arg)
-{
-	struct e100_serial * info = (struct e100_serial *)tty->driver_data;
-
-	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
-	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
-	    (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
-		if (tty_io_error(tty))
-			return -EIO;
-	}
-
-	switch (cmd) {
-	case TIOCGSERIAL:
-		return get_serial_info(info,
-				       (struct serial_struct *) arg);
-	case TIOCSSERIAL:
-		return set_serial_info(info,
-				       (struct serial_struct *) arg);
-	case TIOCSERGETLSR: /* Get line status register */
-		return get_lsr_info(info, (unsigned int *) arg);
-
-	case TIOCSERGSTRUCT:
-		if (copy_to_user((struct e100_serial *) arg,
-				 info, sizeof(struct e100_serial)))
-			return -EFAULT;
-		return 0;
-
-#if defined(CONFIG_ETRAX_RS485)
-	case TIOCSERSETRS485:
-	{
-		/* In this ioctl we still use the old structure
-		 * rs485_control for backward compatibility
-		 * (if we use serial_rs485, then old user-level code
-		 * wouldn't work anymore...).
-		 * The use of this ioctl is deprecated: use TIOCSRS485
-		 * instead.*/
-		struct rs485_control rs485ctrl;
-		struct serial_rs485 rs485data;
-		printk(KERN_DEBUG "The use of this ioctl is deprecated. Use TIOCSRS485 instead\n");
-		if (copy_from_user(&rs485ctrl, (struct rs485_control *)arg,
-				sizeof(rs485ctrl)))
-			return -EFAULT;
-
-		rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send;
-		rs485data.flags = 0;
-
-		if (rs485ctrl.enabled)
-			rs485data.flags |= SER_RS485_ENABLED;
-		else
-			rs485data.flags &= ~(SER_RS485_ENABLED);
-
-		if (rs485ctrl.rts_on_send)
-			rs485data.flags |= SER_RS485_RTS_ON_SEND;
-		else
-			rs485data.flags &= ~(SER_RS485_RTS_ON_SEND);
-
-		if (rs485ctrl.rts_after_sent)
-			rs485data.flags |= SER_RS485_RTS_AFTER_SEND;
-		else
-			rs485data.flags &= ~(SER_RS485_RTS_AFTER_SEND);
-
-		return e100_enable_rs485(tty, &rs485data);
-	}
-
-	case TIOCSRS485:
-	{
-		/* This is the new version of TIOCSRS485, with new
-		 * data structure serial_rs485 */
-		struct serial_rs485 rs485data;
-		if (copy_from_user(&rs485data, (struct rs485_control *)arg,
-				sizeof(rs485data)))
-			return -EFAULT;
-
-		return e100_enable_rs485(tty, &rs485data);
-	}
-
-	case TIOCGRS485:
-	{
-		struct serial_rs485 *rs485data =
-			&(((struct e100_serial *)tty->driver_data)->rs485);
-		/* This is the ioctl to get RS485 data from user-space */
-		if (copy_to_user((struct serial_rs485 *) arg,
-					rs485data,
-					sizeof(struct serial_rs485)))
-			return -EFAULT;
-		break;
-	}
-
-	case TIOCSERWRRS485:
-	{
-		struct rs485_write rs485wr;
-		if (copy_from_user(&rs485wr, (struct rs485_write *)arg,
-				sizeof(rs485wr)))
-			return -EFAULT;
-
-		return e100_write_rs485(tty, rs485wr.outc, rs485wr.outc_size);
-	}
-#endif
-
-	default:
-		return -ENOIOCTLCMD;
-	}
-	return 0;
-}
-
-static void
-rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
-{
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-
-	change_speed(info);
-
-	/* Handle turning off CRTSCTS */
-	if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty))
-		rs_start(tty);
-
-}
-
-/*
- * ------------------------------------------------------------
- * rs_close()
- *
- * This routine is called when the serial port gets closed.  First, we
- * wait for the last remaining data to be sent.  Then, we unlink its
- * S structure from the interrupt chain if necessary, and we free
- * that IRQ if nothing is left in the chain.
- * ------------------------------------------------------------
- */
-static void
-rs_close(struct tty_struct *tty, struct file * filp)
-{
-	struct e100_serial * info = (struct e100_serial *)tty->driver_data;
-	unsigned long flags;
-
-	if (!info)
-		return;
-
-	/* interrupts are disabled for this entire function */
-
-	local_irq_save(flags);
-
-	if (tty_hung_up_p(filp)) {
-		local_irq_restore(flags);
-		return;
-	}
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("[%d] rs_close ttyS%d, count = %d\n", current->pid,
-	       info->line, info->count);
-#endif
-	if ((tty->count == 1) && (info->port.count != 1)) {
-		/*
-		 * Uh, oh.  tty->count is 1, which means that the tty
-		 * structure will be freed.  Info->count should always
-		 * be one in these conditions.  If it's greater than
-		 * one, we've got real problems, since it means the
-		 * serial port won't be shutdown.
-		 */
-		printk(KERN_ERR
-		       "rs_close: bad serial port count; tty->count is 1, "
-		       "info->count is %d\n", info->port.count);
-		info->port.count = 1;
-	}
-	if (--info->port.count < 0) {
-		printk(KERN_ERR "rs_close: bad serial port count for ttyS%d: %d\n",
-		       info->line, info->port.count);
-		info->port.count = 0;
-	}
-	if (info->port.count) {
-		local_irq_restore(flags);
-		return;
-	}
-	/*
-	 * Now we wait for the transmit buffer to clear; and we notify
-	 * the line discipline to only process XON/XOFF characters.
-	 */
-	tty->closing = 1;
-	if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE)
-		tty_wait_until_sent(tty, info->port.closing_wait);
-	/*
-	 * At this point we stop accepting input.  To do this, we
-	 * disable the serial receiver and the DMA receive interrupt.
-	 */
-#ifdef SERIAL_HANDLE_EARLY_ERRORS
-	e100_disable_serial_data_irq(info);
-#endif
-
-	e100_disable_rx(info);
-	e100_disable_rx_irq(info);
-
-	if (tty_port_initialized(&info->port)) {
-		/*
-		 * Before we drop DTR, make sure the UART transmitter
-		 * has completely drained; this is especially
-		 * important as we have a transmit FIFO!
-		 */
-		rs_wait_until_sent(tty, HZ);
-	}
-
-	shutdown(info);
-	rs_flush_buffer(tty);
-	tty_ldisc_flush(tty);
-	tty->closing = 0;
-	info->event = 0;
-	info->port.tty = NULL;
-	if (info->port.blocked_open) {
-		if (info->port.close_delay)
-			schedule_timeout_interruptible(info->port.close_delay);
-		wake_up_interruptible(&info->port.open_wait);
-	}
-	local_irq_restore(flags);
-	tty_port_set_active(&info->port, 0);
-
-	/* port closed */
-
-#if defined(CONFIG_ETRAX_RS485)
-	if (info->rs485.flags & SER_RS485_ENABLED) {
-		info->rs485.flags &= ~(SER_RS485_ENABLED);
-#if defined(CONFIG_ETRAX_RS485_ON_PA)
-		*R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
-#endif
-	}
-#endif
-
-	/*
-	 * Release any allocated DMA irq's.
-	 */
-	if (info->dma_in_enabled) {
-		free_irq(info->dma_in_irq_nbr, info);
-		cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description);
-		info->uses_dma_in = 0;
-#ifdef SERIAL_DEBUG_OPEN
-		printk(KERN_DEBUG "DMA irq '%s' freed\n",
-			info->dma_in_irq_description);
-#endif
-	}
-	if (info->dma_out_enabled) {
-		free_irq(info->dma_out_irq_nbr, info);
-		cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description);
-		info->uses_dma_out = 0;
-#ifdef SERIAL_DEBUG_OPEN
-		printk(KERN_DEBUG "DMA irq '%s' freed\n",
-			info->dma_out_irq_description);
-#endif
-	}
-}
-
-/*
- * rs_wait_until_sent() --- wait until the transmitter is empty
- */
-static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-	unsigned long orig_jiffies;
-	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
-	unsigned long curr_time = jiffies;
-	unsigned long curr_time_usec = GET_JIFFIES_USEC();
-	long elapsed_usec =
-		(curr_time - info->last_tx_active) * (1000000/HZ) +
-		curr_time_usec - info->last_tx_active_usec;
-
-	/*
-	 * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO
-	 * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k)
-	 */
-	orig_jiffies = jiffies;
-	while (info->xmit.head != info->xmit.tail || /* More in send queue */
-	       (*info->ostatusadr & 0x007f) ||  /* more in FIFO */
-	       (elapsed_usec < 2*info->char_time_usec)) {
-		schedule_timeout_interruptible(1);
-		if (signal_pending(current))
-			break;
-		if (timeout && time_after(jiffies, orig_jiffies + timeout))
-			break;
-		curr_time = jiffies;
-		curr_time_usec = GET_JIFFIES_USEC();
-		elapsed_usec =
-			(curr_time - info->last_tx_active) * (1000000/HZ) +
-			curr_time_usec - info->last_tx_active_usec;
-	}
-	set_current_state(TASK_RUNNING);
-}
-
-/*
- * rs_hangup() --- called by tty_hangup() when a hangup is signaled.
- */
-void
-rs_hangup(struct tty_struct *tty)
-{
-	struct e100_serial * info = (struct e100_serial *)tty->driver_data;
-
-	rs_flush_buffer(tty);
-	shutdown(info);
-	info->event = 0;
-	info->port.count = 0;
-	tty_port_set_active(&info->port, 0);
-	info->port.tty = NULL;
-	wake_up_interruptible(&info->port.open_wait);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_open() and friends
- * ------------------------------------------------------------
- */
-static int
-block_til_ready(struct tty_struct *tty, struct file * filp,
-		struct e100_serial *info)
-{
-	DECLARE_WAITQUEUE(wait, current);
-	unsigned long	flags;
-	int		retval;
-	int		do_clocal = 0;
-
-	/*
-	 * If non-blocking mode is set, or the port is not enabled,
-	 * then make the check up front and then exit.
-	 */
-	if ((filp->f_flags & O_NONBLOCK) || tty_io_error(tty)) {
-		tty_port_set_active(&info->port, 1);
-		return 0;
-	}
-
-	if (C_CLOCAL(tty))
-		do_clocal = 1;
-
-	/*
-	 * Block waiting for the carrier detect and the line to become
-	 * free (i.e., not in use by the callout).  While we are in
-	 * this loop, info->port.count is dropped by one, so that
-	 * rs_close() knows when to free things.  We restore it upon
-	 * exit, either normal or abnormal.
-	 */
-	retval = 0;
-	add_wait_queue(&info->port.open_wait, &wait);
-#ifdef SERIAL_DEBUG_OPEN
-	printk("block_til_ready before block: ttyS%d, count = %d\n",
-	       info->line, info->port.count);
-#endif
-	local_irq_save(flags);
-	info->port.count--;
-	local_irq_restore(flags);
-	info->port.blocked_open++;
-	while (1) {
-		local_irq_save(flags);
-		/* assert RTS and DTR */
-		e100_rts(info, 1);
-		e100_dtr(info, 1);
-		local_irq_restore(flags);
-		set_current_state(TASK_INTERRUPTIBLE);
-		if (tty_hung_up_p(filp) || !tty_port_initialized(&info->port)) {
-#ifdef SERIAL_DO_RESTART
-			if (info->port.flags & ASYNC_HUP_NOTIFY)
-				retval = -EAGAIN;
-			else
-				retval = -ERESTARTSYS;
-#else
-			retval = -EAGAIN;
-#endif
-			break;
-		}
-		if (do_clocal)
-			/* && (do_clocal || DCD_IS_ASSERTED) */
-			break;
-		if (signal_pending(current)) {
-			retval = -ERESTARTSYS;
-			break;
-		}
-#ifdef SERIAL_DEBUG_OPEN
-		printk("block_til_ready blocking: ttyS%d, count = %d\n",
-		       info->line, info->port.count);
-#endif
-		tty_unlock(tty);
-		schedule();
-		tty_lock(tty);
-	}
-	set_current_state(TASK_RUNNING);
-	remove_wait_queue(&info->port.open_wait, &wait);
-	if (!tty_hung_up_p(filp))
-		info->port.count++;
-	info->port.blocked_open--;
-#ifdef SERIAL_DEBUG_OPEN
-	printk("block_til_ready after blocking: ttyS%d, count = %d\n",
-	       info->line, info->port.count);
-#endif
-	if (retval)
-		return retval;
-	tty_port_set_active(&info->port, 1);
-	return 0;
-}
-
-static void
-deinit_port(struct e100_serial *info)
-{
-	if (info->dma_out_enabled) {
-		cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description);
-		free_irq(info->dma_out_irq_nbr, info);
-	}
-	if (info->dma_in_enabled) {
-		cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description);
-		free_irq(info->dma_in_irq_nbr, info);
-	}
-}
-
-/*
- * This routine is called whenever a serial port is opened.
- * It performs the serial-specific initialization for the tty structure.
- */
-static int
-rs_open(struct tty_struct *tty, struct file * filp)
-{
-	struct e100_serial	*info;
-	int 			retval;
-	int                     allocated_resources = 0;
-
-	info = rs_table + tty->index;
-	if (!info->enabled)
-		return -ENODEV;
-
-#ifdef SERIAL_DEBUG_OPEN
-        printk("[%d] rs_open %s, count = %d\n", current->pid, tty->name,
- 	       info->port.count);
-#endif
-
-	info->port.count++;
-	tty->driver_data = info;
-	info->port.tty = tty;
-
-	info->port.low_latency = !!(info->port.flags & ASYNC_LOW_LATENCY);
-
-	/*
-	 * If DMA is enabled try to allocate the irq's.
-	 */
-	if (info->port.count == 1) {
-		allocated_resources = 1;
-		if (info->dma_in_enabled) {
-			if (request_irq(info->dma_in_irq_nbr,
-					rec_interrupt,
-					info->dma_in_irq_flags,
-					info->dma_in_irq_description,
-					info)) {
-				printk(KERN_WARNING "DMA irq '%s' busy; "
-					"falling back to non-DMA mode\n",
-					info->dma_in_irq_description);
-				/* Make sure we never try to use DMA in */
-				/* for the port again. */
-				info->dma_in_enabled = 0;
-			} else if (cris_request_dma(info->dma_in_nbr,
-					info->dma_in_irq_description,
-					DMA_VERBOSE_ON_ERROR,
-					info->dma_owner)) {
-				free_irq(info->dma_in_irq_nbr, info);
-				printk(KERN_WARNING "DMA '%s' busy; "
-					"falling back to non-DMA mode\n",
-					info->dma_in_irq_description);
-				/* Make sure we never try to use DMA in */
-				/* for the port again. */
-				info->dma_in_enabled = 0;
-			}
-#ifdef SERIAL_DEBUG_OPEN
-			else
-				printk(KERN_DEBUG "DMA irq '%s' allocated\n",
-					info->dma_in_irq_description);
-#endif
-		}
-		if (info->dma_out_enabled) {
-			if (request_irq(info->dma_out_irq_nbr,
-					       tr_interrupt,
-					       info->dma_out_irq_flags,
-					       info->dma_out_irq_description,
-					       info)) {
-				printk(KERN_WARNING "DMA irq '%s' busy; "
-					"falling back to non-DMA mode\n",
-					info->dma_out_irq_description);
-				/* Make sure we never try to use DMA out */
-				/* for the port again. */
-				info->dma_out_enabled = 0;
-			} else if (cris_request_dma(info->dma_out_nbr,
-					     info->dma_out_irq_description,
-					     DMA_VERBOSE_ON_ERROR,
-					     info->dma_owner)) {
-				free_irq(info->dma_out_irq_nbr, info);
-				printk(KERN_WARNING "DMA '%s' busy; "
-					"falling back to non-DMA mode\n",
-					info->dma_out_irq_description);
-				/* Make sure we never try to use DMA out */
-				/* for the port again. */
-				info->dma_out_enabled = 0;
-			}
-#ifdef SERIAL_DEBUG_OPEN
-			else
-				printk(KERN_DEBUG "DMA irq '%s' allocated\n",
-					info->dma_out_irq_description);
-#endif
-		}
-	}
-
-	/*
-	 * Start up the serial port
-	 */
-
-	retval = startup(info);
-	if (retval) {
-		if (allocated_resources)
-			deinit_port(info);
-
-		/* FIXME Decrease count info->port.count here too? */
-		return retval;
-	}
-
-
-	retval = block_til_ready(tty, filp, info);
-	if (retval) {
-#ifdef SERIAL_DEBUG_OPEN
-		printk("rs_open returning after block_til_ready with %d\n",
-		       retval);
-#endif
-		if (allocated_resources)
-			deinit_port(info);
-
-		return retval;
-	}
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("rs_open ttyS%d successful...\n", info->line);
-#endif
-	DLOG_INT_TRIG( log_int_pos = 0);
-
-	DFLIP(	if (info->line == SERIAL_DEBUG_LINE) {
-			info->icount.rx = 0;
-		} );
-
-	return 0;
-}
-
-#ifdef CONFIG_PROC_FS
-/*
- * /proc fs routines....
- */
-
-static void seq_line_info(struct seq_file *m, struct e100_serial *info)
-{
-	unsigned long tmp;
-
-	seq_printf(m, "%d: uart:E100 port:%lX irq:%d",
-		   info->line, (unsigned long)info->ioport, info->irq);
-
-	if (!info->ioport || (info->type == PORT_UNKNOWN)) {
-		seq_printf(m, "\n");
-		return;
-	}
-
-	seq_printf(m, " baud:%d", info->baud);
-	seq_printf(m, " tx:%lu rx:%lu",
-		       (unsigned long)info->icount.tx,
-		       (unsigned long)info->icount.rx);
-	tmp = CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
-	if (tmp)
-		seq_printf(m, " tx_pend:%lu/%lu",
-			   (unsigned long)tmp,
-			   (unsigned long)SERIAL_XMIT_SIZE);
-
-	seq_printf(m, " rx_pend:%lu/%lu",
-		   (unsigned long)info->recv_cnt,
-		   (unsigned long)info->max_recv_cnt);
-
-#if 1
-	if (info->port.tty) {
-		if (info->port.tty->stopped)
-			seq_printf(m, " stopped:%i",
-				   (int)info->port.tty->stopped);
-	}
-
-	{
-		unsigned char rstat = info->ioport[REG_STATUS];
-		if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect))
-			seq_printf(m, " xoff_detect:1");
-	}
-
-#endif
-
-	if (info->icount.frame)
-		seq_printf(m, " fe:%lu", (unsigned long)info->icount.frame);
-
-	if (info->icount.parity)
-		seq_printf(m, " pe:%lu", (unsigned long)info->icount.parity);
-
-	if (info->icount.brk)
-		seq_printf(m, " brk:%lu", (unsigned long)info->icount.brk);
-
-	if (info->icount.overrun)
-		seq_printf(m, " oe:%lu", (unsigned long)info->icount.overrun);
-
-	/*
-	 * Last thing is the RS-232 status lines
-	 */
-	if (!E100_RTS_GET(info))
-		seq_puts(m, "|RTS");
-	if (!E100_CTS_GET(info))
-		seq_puts(m, "|CTS");
-	if (!E100_DTR_GET(info))
-		seq_puts(m, "|DTR");
-	if (!E100_DSR_GET(info))
-		seq_puts(m, "|DSR");
-	if (!E100_CD_GET(info))
-		seq_puts(m, "|CD");
-	if (!E100_RI_GET(info))
-		seq_puts(m, "|RI");
-	seq_puts(m, "\n");
-}
-
-
-static int crisv10_proc_show(struct seq_file *m, void *v)
-{
-	int i;
-
-	seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version);
-
-	for (i = 0; i < NR_PORTS; i++) {
-		if (!rs_table[i].enabled)
-			continue;
-		seq_line_info(m, &rs_table[i]);
-	}
-#ifdef DEBUG_LOG_INCLUDED
-	for (i = 0; i < debug_log_pos; i++) {
-		seq_printf(m, "%-4i %lu.%lu ",
-			 i, debug_log[i].time,
-			 timer_data_to_ns(debug_log[i].timer_data));
-		seq_printf(m, debug_log[i].string, debug_log[i].value);
-	}
-	seq_printf(m, "debug_log %i/%i\n", i, DEBUG_LOG_SIZE);
-	debug_log_pos = 0;
-#endif
-	return 0;
-}
-
-static int crisv10_proc_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, crisv10_proc_show, NULL);
-}
-
-static const struct file_operations crisv10_proc_fops = {
-	.owner		= THIS_MODULE,
-	.open		= crisv10_proc_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-#endif
-
-
-/* Finally, routines used to initialize the serial driver. */
-
-static void show_serial_version(void)
-{
-	printk(KERN_INFO
-	       "ETRAX 100LX serial-driver %s, "
-	       "(c) 2000-2004 Axis Communications AB\r\n",
-	       &serial_version[11]); /* "$Revision: x.yy" */
-}
-
-/* rs_init inits the driver at boot (using the initcall chain) */
-
-static const struct tty_operations rs_ops = {
-	.open = rs_open,
-	.close = rs_close,
-	.write = rs_write,
-	.flush_chars = rs_flush_chars,
-	.write_room = rs_write_room,
-	.chars_in_buffer = rs_chars_in_buffer,
-	.flush_buffer = rs_flush_buffer,
-	.ioctl = rs_ioctl,
-	.throttle = rs_throttle,
-        .unthrottle = rs_unthrottle,
-	.set_termios = rs_set_termios,
-	.stop = rs_stop,
-	.start = rs_start,
-	.hangup = rs_hangup,
-	.break_ctl = rs_break,
-	.send_xchar = rs_send_xchar,
-	.wait_until_sent = rs_wait_until_sent,
-	.tiocmget = rs_tiocmget,
-	.tiocmset = rs_tiocmset,
-#ifdef CONFIG_PROC_FS
-	.proc_fops = &crisv10_proc_fops,
-#endif
-};
-
-static int __init rs_init(void)
-{
-	int i;
-	struct e100_serial *info;
-	struct tty_driver *driver = alloc_tty_driver(NR_PORTS);
-
-	if (!driver)
-		return -ENOMEM;
-
-	show_serial_version();
-
-	/* Setup the timed flush handler system */
-
-#if !defined(CONFIG_ETRAX_SERIAL_FAST_TIMER)
-	timer_setup(&flush_timer, timed_flush_handler, 0);
-	mod_timer(&flush_timer, jiffies + 5);
-#endif
-
-#if defined(CONFIG_ETRAX_RS485)
-#if defined(CONFIG_ETRAX_RS485_ON_PA)
-	if (cris_io_interface_allocate_pins(if_serial_0, 'a', rs485_pa_bit,
-			rs485_pa_bit)) {
-		printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
-			"RS485 pin\n");
-		put_tty_driver(driver);
-		return -EBUSY;
-	}
-#endif
-#endif
-
-	/* Initialize the tty_driver structure */
-
-	driver->driver_name = "serial";
-	driver->name = "ttyS";
-	driver->major = TTY_MAJOR;
-	driver->minor_start = 64;
-	driver->type = TTY_DRIVER_TYPE_SERIAL;
-	driver->subtype = SERIAL_TYPE_NORMAL;
-	driver->init_termios = tty_std_termios;
-	driver->init_termios.c_cflag =
-		B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */
-	driver->init_termios.c_ispeed = 115200;
-	driver->init_termios.c_ospeed = 115200;
-	driver->flags = TTY_DRIVER_REAL_RAW;
-
-	tty_set_operations(driver, &rs_ops);
-        serial_driver = driver;
-
-	/* do some initializing for the separate ports */
-	for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) {
-		if (info->enabled) {
-			if (cris_request_io_interface(info->io_if,
-					info->io_if_description)) {
-				printk(KERN_ERR "ETRAX100LX async serial: "
-					"Could not allocate IO pins for "
-					"%s, port %d\n",
-					info->io_if_description, i);
-				info->enabled = 0;
-			}
-		}
-		tty_port_init(&info->port);
-		info->uses_dma_in = 0;
-		info->uses_dma_out = 0;
-		info->line = i;
-		info->port.tty = NULL;
-		info->type = PORT_ETRAX;
-		info->tr_running = 0;
-		info->forced_eop = 0;
-		info->baud_base = DEF_BAUD_BASE;
-		info->custom_divisor = 0;
-		info->x_char = 0;
-		info->event = 0;
-		info->xmit.buf = NULL;
-		info->xmit.tail = info->xmit.head = 0;
-		info->first_recv_buffer = info->last_recv_buffer = NULL;
-		info->recv_cnt = info->max_recv_cnt = 0;
-		info->last_tx_active_usec = 0;
-		info->last_tx_active = 0;
-
-#if defined(CONFIG_ETRAX_RS485)
-		/* Set sane defaults */
-		info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND);
-		info->rs485.flags |= SER_RS485_RTS_AFTER_SEND;
-		info->rs485.delay_rts_before_send = 0;
-		info->rs485.flags &= ~(SER_RS485_ENABLED);
-#endif
-		INIT_WORK(&info->work, do_softint);
-
-		if (info->enabled) {
-			printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n",
-			       serial_driver->name, info->line, info->ioport);
-		}
-		tty_port_link_device(&info->port, driver, i);
-	}
-
-	if (tty_register_driver(driver))
-		panic("Couldn't register serial driver\n");
-
-#ifdef CONFIG_ETRAX_FAST_TIMER
-#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
-	memset(fast_timers, 0, sizeof(fast_timers));
-#endif
-#ifdef CONFIG_ETRAX_RS485
-	memset(fast_timers_rs485, 0, sizeof(fast_timers_rs485));
-#endif
-	fast_timer_init();
-#endif
-
-#ifndef CONFIG_ETRAX_KGDB
-	/* Not needed in simulator.  May only complicate stuff. */
-	/* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */
-
-	if (request_irq(SERIAL_IRQ_NBR, ser_interrupt,
-			IRQF_SHARED, "serial ", driver))
-		panic("%s: Failed to request irq8", __func__);
-
-#endif
-
-	return 0;
-}
-
-/* this makes sure that rs_init is called during kernel boot */
-device_initcall(rs_init);
diff --git a/drivers/tty/serial/crisv10.h b/drivers/tty/serial/crisv10.h
deleted file mode 100644
index 79ba2bc95d3d..000000000000
--- a/drivers/tty/serial/crisv10.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * serial.h: Arch-dep definitions for the Etrax100 serial driver.
- *
- * Copyright (C) 1998-2007 Axis Communications AB
- */
-
-#ifndef _ETRAX_SERIAL_H
-#define _ETRAX_SERIAL_H
-
-#include <linux/circ_buf.h>
-#include <asm/termios.h>
-#include <asm/dma.h>
-#include <arch/io_interface_mux.h>
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-#define SERIAL_RECV_DESCRIPTORS 8
-
-struct etrax_recv_buffer {
-	struct etrax_recv_buffer *next;
-	unsigned short length;
-	unsigned char error;
-	unsigned char pad;
-
-	unsigned char buffer[0];
-};
-
-struct e100_serial {
-	struct tty_port port;
-	int baud;
-	volatile u8	*ioport;	/* R_SERIALx_CTRL */
-	u32		irq;	/* bitnr in R_IRQ_MASK2 for dmaX_descr */
-
-	/* Output registers */
-	volatile u8 *oclrintradr;	/* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32 *ofirstadr;	/* adr to R_DMA_CHx_FIRST */
-	volatile u8 *ocmdadr;		/* adr to R_DMA_CHx_CMD */
-	const volatile u8 *ostatusadr;	/* adr to R_DMA_CHx_STATUS */
-
-	/* Input registers */
-	volatile u8 *iclrintradr;	/* adr to R_DMA_CHx_CLR_INTR */
-	volatile u32 *ifirstadr;	/* adr to R_DMA_CHx_FIRST */
-	volatile u8 *icmdadr;		/* adr to R_DMA_CHx_CMD */
-	volatile u32 *idescradr;	/* adr to R_DMA_CHx_DESCR */
-
-	u8 rx_ctrl;	/* shadow for R_SERIALx_REC_CTRL */
-	u8 tx_ctrl;	/* shadow for R_SERIALx_TR_CTRL */
-	u8 iseteop;	/* bit number for R_SET_EOP for the input dma */
-	int enabled;	/* Set to 1 if the port is enabled in HW config */
-
-	u8 dma_out_enabled;	/* Set to 1 if DMA should be used */
-	u8 dma_in_enabled;	/* Set to 1 if DMA should be used */
-
-	/* end of fields defined in rs_table[] in .c-file */
-	int		dma_owner;
-	unsigned int	dma_in_nbr;
-	unsigned int	dma_out_nbr;
-	unsigned int	dma_in_irq_nbr;
-	unsigned int	dma_out_irq_nbr;
-	unsigned long	dma_in_irq_flags;
-	unsigned long	dma_out_irq_flags;
-	char		*dma_in_irq_description;
-	char		*dma_out_irq_description;
-
-	enum cris_io_interface io_if;
-	char            *io_if_description;
-
-	u8		uses_dma_in;  /* Set to 1 if DMA is used */
-	u8		uses_dma_out; /* Set to 1 if DMA is used */
-	u8		forced_eop;   /* a fifo eop has been forced */
-	int			baud_base;     /* For special baudrates */
-	int			custom_divisor; /* For special baudrates */
-	struct etrax_dma_descr	tr_descr;
-	struct etrax_dma_descr	rec_descr[SERIAL_RECV_DESCRIPTORS];
-	int			cur_rec_descr;
-
-	volatile int		tr_running; /* 1 if output is running */
-
-	int			x_char;	/* xon/xoff character */
-	unsigned long		event;
-	int			line;
-	int			type;  /* PORT_ETRAX */
-	struct circ_buf		xmit;
-	struct etrax_recv_buffer *first_recv_buffer;
-	struct etrax_recv_buffer *last_recv_buffer;
-	unsigned int		recv_cnt;
-	unsigned int		max_recv_cnt;
-
-	struct work_struct	work;
-	struct async_icount	icount;   /* error-statistics etc.*/
-
-	unsigned long char_time_usec;       /* The time for 1 char, in usecs */
-	unsigned long flush_time_usec;      /* How often we should flush */
-	unsigned long last_tx_active_usec;  /* Last tx usec in the jiffies */
-	unsigned long last_tx_active;       /* Last tx time in jiffies */
-	unsigned long last_rx_active_usec;  /* Last rx usec in the jiffies */
-	unsigned long last_rx_active;       /* Last rx time in jiffies */
-
-	int break_detected_cnt;
-	int errorcode;
-
-#ifdef CONFIG_ETRAX_RS485
-	struct serial_rs485	rs485;  /* RS-485 support */
-#endif
-};
-
-/* this PORT is not in the standard serial.h. it's not actually used for
- * anything since we only have one type of async serial-port anyway in this
- * system.
- */
-
-#define PORT_ETRAX 1
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP	0
-
-#endif /* __KERNEL__ */
-
-#endif /* !_ETRAX_SERIAL_H */
diff --git a/drivers/tty/serial/etraxfs-uart.c b/drivers/tty/serial/etraxfs-uart.c
deleted file mode 100644
index 24bf6bfb29b4..000000000000
--- a/drivers/tty/serial/etraxfs-uart.c
+++ /dev/null
@@ -1,960 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/platform_device.h>
-#include <linux/serial_core.h>
-#include <linux/tty_flip.h>
-#include <linux/of.h>
-#include <linux/gpio.h>
-#include <linux/of_irq.h>
-#include <linux/of_address.h>
-#include <hwregs/ser_defs.h>
-
-#include "serial_mctrl_gpio.h"
-
-#define DRV_NAME "etraxfs-uart"
-#define UART_NR CONFIG_ETRAX_SERIAL_PORTS
-
-#define MODIFY_REG(instance, reg, var)				\
-	do {							\
-		if (REG_RD_INT(ser, instance, reg) !=		\
-		    REG_TYPE_CONV(int, reg_ser_##reg, var))	\
-			REG_WR(ser, instance, reg, var);	\
-	} while (0)
-
-struct uart_cris_port {
-	struct uart_port port;
-
-	int initialized;
-	int irq;
-
-	void __iomem *regi_ser;
-
-	struct mctrl_gpios *gpios;
-
-	int write_ongoing;
-};
-
-static struct uart_driver etraxfs_uart_driver;
-static struct uart_port *console_port;
-static int console_baud = 115200;
-static struct uart_cris_port *etraxfs_uart_ports[UART_NR];
-
-static void cris_serial_port_init(struct uart_port *port, int line);
-static void etraxfs_uart_stop_rx(struct uart_port *port);
-static inline void etraxfs_uart_start_tx_bottom(struct uart_port *port);
-
-#ifdef CONFIG_SERIAL_ETRAXFS_CONSOLE
-static void
-cris_console_write(struct console *co, const char *s, unsigned int count)
-{
-	struct uart_cris_port *up;
-	int i;
-	reg_ser_r_stat_din stat;
-	reg_ser_rw_tr_dma_en tr_dma_en, old;
-
-	up = etraxfs_uart_ports[co->index];
-
-	if (!up)
-		return;
-
-	/* Switch to manual mode. */
-	tr_dma_en = old = REG_RD(ser, up->regi_ser, rw_tr_dma_en);
-	if (tr_dma_en.en == regk_ser_yes) {
-		tr_dma_en.en = regk_ser_no;
-		REG_WR(ser, up->regi_ser, rw_tr_dma_en, tr_dma_en);
-	}
-
-	/* Send data. */
-	for (i = 0; i < count; i++) {
-		/* LF -> CRLF */
-		if (s[i] == '\n') {
-			do {
-				stat = REG_RD(ser, up->regi_ser, r_stat_din);
-			} while (!stat.tr_rdy);
-			REG_WR_INT(ser, up->regi_ser, rw_dout, '\r');
-		}
-		/* Wait until transmitter is ready and send. */
-		do {
-			stat = REG_RD(ser, up->regi_ser, r_stat_din);
-		} while (!stat.tr_rdy);
-		REG_WR_INT(ser, up->regi_ser, rw_dout, s[i]);
-	}
-
-	/* Restore mode. */
-	if (tr_dma_en.en != old.en)
-		REG_WR(ser, up->regi_ser, rw_tr_dma_en, old);
-}
-
-static int __init
-cris_console_setup(struct console *co, char *options)
-{
-	struct uart_port *port;
-	int baud = 115200;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	if (co->index < 0 || co->index >= UART_NR)
-		co->index = 0;
-	port = &etraxfs_uart_ports[co->index]->port;
-	console_port = port;
-
-	co->flags |= CON_CONSDEV;
-
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	console_baud = baud;
-	cris_serial_port_init(port, co->index);
-	uart_set_options(port, co, baud, parity, bits, flow);
-
-	return 0;
-}
-
-static struct console cris_console = {
-	.name = "ttyS",
-	.write = cris_console_write,
-	.device = uart_console_device,
-	.setup = cris_console_setup,
-	.flags = CON_PRINTBUFFER,
-	.index = -1,
-	.data = &etraxfs_uart_driver,
-};
-#endif /* CONFIG_SERIAL_ETRAXFS_CONSOLE */
-
-static struct uart_driver etraxfs_uart_driver = {
-	.owner = THIS_MODULE,
-	.driver_name = "serial",
-	.dev_name = "ttyS",
-	.major = TTY_MAJOR,
-	.minor = 64,
-	.nr = UART_NR,
-#ifdef CONFIG_SERIAL_ETRAXFS_CONSOLE
-	.cons = &cris_console,
-#endif /* CONFIG_SERIAL_ETRAXFS_CONSOLE */
-};
-
-static inline int crisv32_serial_get_rts(struct uart_cris_port *up)
-{
-	void __iomem *regi_ser = up->regi_ser;
-	/*
-	 * Return what the user has controlled rts to or
-	 * what the pin is? (if auto_rts is used it differs during tx)
-	 */
-	reg_ser_r_stat_din rstat = REG_RD(ser, regi_ser, r_stat_din);
-
-	return !(rstat.rts_n == regk_ser_active);
-}
-
-/*
- * A set = 0 means 3.3V on the pin, bitvalue: 0=active, 1=inactive
- *                                            0=0V    , 1=3.3V
- */
-static inline void crisv32_serial_set_rts(struct uart_cris_port *up,
-					  int set, int force)
-{
-	void __iomem *regi_ser = up->regi_ser;
-
-	unsigned long flags;
-	reg_ser_rw_rec_ctrl rec_ctrl;
-
-	local_irq_save(flags);
-	rec_ctrl = REG_RD(ser, regi_ser, rw_rec_ctrl);
-
-	if (set)
-		rec_ctrl.rts_n = regk_ser_active;
-	else
-		rec_ctrl.rts_n = regk_ser_inactive;
-	REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl);
-	local_irq_restore(flags);
-}
-
-static inline int crisv32_serial_get_cts(struct uart_cris_port *up)
-{
-	void __iomem *regi_ser = up->regi_ser;
-	reg_ser_r_stat_din rstat = REG_RD(ser, regi_ser, r_stat_din);
-
-	return (rstat.cts_n == regk_ser_active);
-}
-
-/*
- * Send a single character for XON/XOFF purposes.  We do it in this separate
- * function instead of the alternative support port.x_char, in the ...start_tx
- * function, so we don't mix up this case with possibly enabling transmission
- * of queued-up data (in case that's disabled after *receiving* an XOFF or
- * negative CTS).  This function is used for both DMA and non-DMA case; see HW
- * docs specifically blessing sending characters manually when DMA for
- * transmission is enabled and running.  We may be asked to transmit despite
- * the transmitter being disabled by a ..._stop_tx call so we need to enable
- * it temporarily but restore the state afterwards.
- */
-static void etraxfs_uart_send_xchar(struct uart_port *port, char ch)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	reg_ser_rw_dout dout = { .data = ch };
-	reg_ser_rw_ack_intr ack_intr = { .tr_rdy = regk_ser_yes };
-	reg_ser_r_stat_din rstat;
-	reg_ser_rw_tr_ctrl prev_tr_ctrl, tr_ctrl;
-	void __iomem *regi_ser = up->regi_ser;
-	unsigned long flags;
-
-	/*
-	 * Wait for tr_rdy in case a character is already being output.  Make
-	 * sure we have integrity between the register reads and the writes
-	 * below, but don't busy-wait with interrupts off and the port lock
-	 * taken.
-	 */
-	spin_lock_irqsave(&port->lock, flags);
-	do {
-		spin_unlock_irqrestore(&port->lock, flags);
-		spin_lock_irqsave(&port->lock, flags);
-		prev_tr_ctrl = tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl);
-		rstat = REG_RD(ser, regi_ser, r_stat_din);
-	} while (!rstat.tr_rdy);
-
-	/*
-	 * Ack an interrupt if one was just issued for the previous character
-	 * that was output.  This is required for non-DMA as the interrupt is
-	 * used as the only indicator that the transmitter is ready and it
-	 * isn't while this x_char is being transmitted.
-	 */
-	REG_WR(ser, regi_ser, rw_ack_intr, ack_intr);
-
-	/* Enable the transmitter in case it was disabled. */
-	tr_ctrl.stop = 0;
-	REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl);
-
-	/*
-	 * Finally, send the blessed character; nothing should stop it now,
-	 * except for an xoff-detected state, which we'll handle below.
-	 */
-	REG_WR(ser, regi_ser, rw_dout, dout);
-	up->port.icount.tx++;
-
-	/* There might be an xoff state to clear. */
-	rstat = REG_RD(ser, up->regi_ser, r_stat_din);
-
-	/*
-	 * Clear any xoff state that *may* have been there to
-	 * inhibit transmission of the character.
-	 */
-	if (rstat.xoff_detect) {
-		reg_ser_rw_xoff_clr xoff_clr = { .clr = 1 };
-		reg_ser_rw_tr_dma_en tr_dma_en;
-
-		REG_WR(ser, regi_ser, rw_xoff_clr, xoff_clr);
-		tr_dma_en = REG_RD(ser, regi_ser, rw_tr_dma_en);
-
-		/*
-		 * If we had an xoff state but cleared it, instead sneak in a
-		 * disabled state for the transmitter, after the character we
-		 * sent.  Thus we keep the port disabled, just as if the xoff
-		 * state was still in effect (or actually, as if stop_tx had
-		 * been called, as we stop DMA too).
-		 */
-		prev_tr_ctrl.stop = 1;
-
-		tr_dma_en.en = 0;
-		REG_WR(ser, regi_ser, rw_tr_dma_en, tr_dma_en);
-	}
-
-	/* Restore "previous" enabled/disabled state of the transmitter. */
-	REG_WR(ser, regi_ser, rw_tr_ctrl, prev_tr_ctrl);
-
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-/*
- * Do not spin_lock_irqsave or disable interrupts by other means here; it's
- * already done by the caller.
- */
-static void etraxfs_uart_start_tx(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	/* we have already done below if a write is ongoing */
-	if (up->write_ongoing)
-		return;
-
-	/* Signal that write is ongoing */
-	up->write_ongoing = 1;
-
-	etraxfs_uart_start_tx_bottom(port);
-}
-
-static inline void etraxfs_uart_start_tx_bottom(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	void __iomem *regi_ser = up->regi_ser;
-	reg_ser_rw_tr_ctrl tr_ctrl;
-	reg_ser_rw_intr_mask intr_mask;
-
-	tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl);
-	tr_ctrl.stop = regk_ser_no;
-	REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl);
-	intr_mask = REG_RD(ser, regi_ser, rw_intr_mask);
-	intr_mask.tr_rdy = regk_ser_yes;
-	REG_WR(ser, regi_ser, rw_intr_mask, intr_mask);
-}
-
-/*
- * This function handles both the DMA and non-DMA case by ordering the
- * transmitter to stop of after the current character.  We don't need to wait
- * for any such character to be completely transmitted; we do that where it
- * matters, like in etraxfs_uart_set_termios.  Don't busy-wait here; see
- * Documentation/serial/driver: this function is called within
- * spin_lock_irq{,save} and thus separate ones would be disastrous (when SMP).
- * There's no documented need to set the txd pin to any particular value;
- * break setting is controlled solely by etraxfs_uart_break_ctl.
- */
-static void etraxfs_uart_stop_tx(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	void __iomem *regi_ser = up->regi_ser;
-	reg_ser_rw_tr_ctrl tr_ctrl;
-	reg_ser_rw_intr_mask intr_mask;
-	reg_ser_rw_tr_dma_en tr_dma_en = {0};
-	reg_ser_rw_xoff_clr xoff_clr = {0};
-
-	/*
-	 * For the non-DMA case, we'd get a tr_rdy interrupt that we're not
-	 * interested in as we're not transmitting any characters.  For the
-	 * DMA case, that interrupt is already turned off, but no reason to
-	 * waste code on conditionals here.
-	 */
-	intr_mask = REG_RD(ser, regi_ser, rw_intr_mask);
-	intr_mask.tr_rdy = regk_ser_no;
-	REG_WR(ser, regi_ser, rw_intr_mask, intr_mask);
-
-	tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl);
-	tr_ctrl.stop = 1;
-	REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl);
-
-	/*
-	 * Always clear possible hardware xoff-detected state here, no need to
-	 * unnecessary consider mctrl settings and when they change.  We clear
-	 * it here rather than in start_tx: both functions are called as the
-	 * effect of XOFF processing, but start_tx is also called when upper
-	 * levels tell the driver that there are more characters to send, so
-	 * avoid adding code there.
-	 */
-	xoff_clr.clr = 1;
-	REG_WR(ser, regi_ser, rw_xoff_clr, xoff_clr);
-
-	/*
-	 * Disable transmitter DMA, so that if we're in XON/XOFF, we can send
-	 * those single characters without also giving go-ahead for queued up
-	 * DMA data.
-	 */
-	tr_dma_en.en = 0;
-	REG_WR(ser, regi_ser, rw_tr_dma_en, tr_dma_en);
-
-	/*
-	 * Make sure that write_ongoing is reset when stopping tx.
-	 */
-	up->write_ongoing = 0;
-}
-
-static void etraxfs_uart_stop_rx(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	void __iomem *regi_ser = up->regi_ser;
-	reg_ser_rw_rec_ctrl rec_ctrl = REG_RD(ser, regi_ser, rw_rec_ctrl);
-
-	rec_ctrl.en = regk_ser_no;
-	REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl);
-}
-
-static unsigned int etraxfs_uart_tx_empty(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned long flags;
-	unsigned int ret;
-	reg_ser_r_stat_din rstat = {0};
-
-	spin_lock_irqsave(&up->port.lock, flags);
-
-	rstat = REG_RD(ser, up->regi_ser, r_stat_din);
-	ret = rstat.tr_empty ? TIOCSER_TEMT : 0;
-
-	spin_unlock_irqrestore(&up->port.lock, flags);
-	return ret;
-}
-static unsigned int etraxfs_uart_get_mctrl(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned int ret;
-
-	ret = 0;
-	if (crisv32_serial_get_rts(up))
-		ret |= TIOCM_RTS;
-	if (crisv32_serial_get_cts(up))
-		ret |= TIOCM_CTS;
-	return mctrl_gpio_get(up->gpios, &ret);
-}
-
-static void etraxfs_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	crisv32_serial_set_rts(up, mctrl & TIOCM_RTS ? 1 : 0, 0);
-	mctrl_gpio_set(up->gpios, mctrl);
-}
-
-static void etraxfs_uart_break_ctl(struct uart_port *port, int break_state)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned long flags;
-	reg_ser_rw_tr_ctrl tr_ctrl;
-	reg_ser_rw_tr_dma_en tr_dma_en;
-	reg_ser_rw_intr_mask intr_mask;
-
-	spin_lock_irqsave(&up->port.lock, flags);
-	tr_ctrl = REG_RD(ser, up->regi_ser, rw_tr_ctrl);
-	tr_dma_en = REG_RD(ser, up->regi_ser, rw_tr_dma_en);
-	intr_mask = REG_RD(ser, up->regi_ser, rw_intr_mask);
-
-	if (break_state != 0) { /* Send break */
-		/*
-		 * We need to disable DMA (if used) or tr_rdy interrupts if no
-		 * DMA.  No need to make this conditional on use of DMA;
-		 * disabling will be a no-op for the other mode.
-		 */
-		intr_mask.tr_rdy = regk_ser_no;
-		tr_dma_en.en = 0;
-
-		/*
-		 * Stop transmission and set the txd pin to 0 after the
-		 * current character.  The txd setting will take effect after
-		 * any current transmission has completed.
-		 */
-		tr_ctrl.stop = 1;
-		tr_ctrl.txd = 0;
-	} else {
-		/* Re-enable the serial interrupt. */
-		intr_mask.tr_rdy = regk_ser_yes;
-
-		tr_ctrl.stop = 0;
-		tr_ctrl.txd = 1;
-	}
-	REG_WR(ser, up->regi_ser, rw_tr_ctrl, tr_ctrl);
-	REG_WR(ser, up->regi_ser, rw_tr_dma_en, tr_dma_en);
-	REG_WR(ser, up->regi_ser, rw_intr_mask, intr_mask);
-
-	spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static void
-transmit_chars_no_dma(struct uart_cris_port *up)
-{
-	int max_count;
-	struct circ_buf *xmit = &up->port.state->xmit;
-
-	void __iomem *regi_ser = up->regi_ser;
-	reg_ser_r_stat_din rstat;
-	reg_ser_rw_ack_intr ack_intr = { .tr_rdy = regk_ser_yes };
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
-		/* No more to send, so disable the interrupt. */
-		reg_ser_rw_intr_mask intr_mask;
-
-		intr_mask = REG_RD(ser, regi_ser, rw_intr_mask);
-		intr_mask.tr_rdy = 0;
-		intr_mask.tr_empty = 0;
-		REG_WR(ser, regi_ser, rw_intr_mask, intr_mask);
-		up->write_ongoing = 0;
-		return;
-	}
-
-	/* If the serport is fast, we send up to max_count bytes before
-	   exiting the loop.  */
-	max_count = 64;
-	do {
-		reg_ser_rw_dout dout = { .data = xmit->buf[xmit->tail] };
-
-		REG_WR(ser, regi_ser, rw_dout, dout);
-		REG_WR(ser, regi_ser, rw_ack_intr, ack_intr);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE-1);
-		up->port.icount.tx++;
-		if (xmit->head == xmit->tail)
-			break;
-		rstat = REG_RD(ser, regi_ser, r_stat_din);
-	} while ((--max_count > 0) && rstat.tr_rdy);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&up->port);
-}
-
-static void receive_chars_no_dma(struct uart_cris_port *up)
-{
-	reg_ser_rs_stat_din stat_din;
-	reg_ser_r_stat_din rstat;
-	struct tty_port *port;
-	struct uart_icount *icount;
-	int max_count = 16;
-	char flag;
-	reg_ser_rw_ack_intr ack_intr = { 0 };
-
-	rstat = REG_RD(ser, up->regi_ser, r_stat_din);
-	icount = &up->port.icount;
-	port = &up->port.state->port;
-
-	do {
-		stat_din = REG_RD(ser, up->regi_ser, rs_stat_din);
-
-		flag = TTY_NORMAL;
-		ack_intr.dav = 1;
-		REG_WR(ser, up->regi_ser, rw_ack_intr, ack_intr);
-		icount->rx++;
-
-		if (stat_din.framing_err | stat_din.par_err | stat_din.orun) {
-			if (stat_din.data == 0x00 &&
-			    stat_din.framing_err) {
-				/* Most likely a break. */
-				flag = TTY_BREAK;
-				icount->brk++;
-			} else if (stat_din.par_err) {
-				flag = TTY_PARITY;
-				icount->parity++;
-			} else if (stat_din.orun) {
-				flag = TTY_OVERRUN;
-				icount->overrun++;
-			} else if (stat_din.framing_err) {
-				flag = TTY_FRAME;
-				icount->frame++;
-			}
-		}
-
-		/*
-		 * If this becomes important, we probably *could* handle this
-		 * gracefully by keeping track of the unhandled character.
-		 */
-		if (!tty_insert_flip_char(port, stat_din.data, flag))
-			panic("%s: No tty buffer space", __func__);
-		rstat = REG_RD(ser, up->regi_ser, r_stat_din);
-	} while (rstat.dav && (max_count-- > 0));
-	spin_unlock(&up->port.lock);
-	tty_flip_buffer_push(port);
-	spin_lock(&up->port.lock);
-}
-
-static irqreturn_t
-ser_interrupt(int irq, void *dev_id)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)dev_id;
-	void __iomem *regi_ser;
-	int handled = 0;
-
-	spin_lock(&up->port.lock);
-
-	regi_ser = up->regi_ser;
-
-	if (regi_ser) {
-		reg_ser_r_masked_intr masked_intr;
-
-		masked_intr = REG_RD(ser, regi_ser, r_masked_intr);
-		/*
-		 * Check what interrupts are active before taking
-		 * actions. If DMA is used the interrupt shouldn't
-		 * be enabled.
-		 */
-		if (masked_intr.dav) {
-			receive_chars_no_dma(up);
-			handled = 1;
-		}
-
-		if (masked_intr.tr_rdy) {
-			transmit_chars_no_dma(up);
-			handled = 1;
-		}
-	}
-	spin_unlock(&up->port.lock);
-	return IRQ_RETVAL(handled);
-}
-
-#ifdef CONFIG_CONSOLE_POLL
-static int etraxfs_uart_get_poll_char(struct uart_port *port)
-{
-	reg_ser_rs_stat_din stat;
-	reg_ser_rw_ack_intr ack_intr = { 0 };
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	do {
-		stat = REG_RD(ser, up->regi_ser, rs_stat_din);
-	} while (!stat.dav);
-
-	/* Ack the data_avail interrupt. */
-	ack_intr.dav = 1;
-	REG_WR(ser, up->regi_ser, rw_ack_intr, ack_intr);
-
-	return stat.data;
-}
-
-static void etraxfs_uart_put_poll_char(struct uart_port *port,
-					unsigned char c)
-{
-	reg_ser_r_stat_din stat;
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	do {
-		stat = REG_RD(ser, up->regi_ser, r_stat_din);
-	} while (!stat.tr_rdy);
-	REG_WR_INT(ser, up->regi_ser, rw_dout, c);
-}
-#endif /* CONFIG_CONSOLE_POLL */
-
-static int etraxfs_uart_startup(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned long flags;
-	reg_ser_rw_intr_mask ser_intr_mask = {0};
-
-	ser_intr_mask.dav = regk_ser_yes;
-
-	if (request_irq(etraxfs_uart_ports[port->line]->irq, ser_interrupt,
-			0, DRV_NAME, etraxfs_uart_ports[port->line]))
-		panic("irq ser%d", port->line);
-
-	spin_lock_irqsave(&up->port.lock, flags);
-
-	REG_WR(ser, up->regi_ser, rw_intr_mask, ser_intr_mask);
-
-	etraxfs_uart_set_mctrl(&up->port, up->port.mctrl);
-
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
-	return 0;
-}
-
-static void etraxfs_uart_shutdown(struct uart_port *port)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned long flags;
-
-	spin_lock_irqsave(&up->port.lock, flags);
-
-	etraxfs_uart_stop_tx(port);
-	etraxfs_uart_stop_rx(port);
-
-	free_irq(etraxfs_uart_ports[port->line]->irq,
-		 etraxfs_uart_ports[port->line]);
-
-	etraxfs_uart_set_mctrl(&up->port, up->port.mctrl);
-
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
-}
-
-static void
-etraxfs_uart_set_termios(struct uart_port *port, struct ktermios *termios,
-			 struct ktermios *old)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-	unsigned long flags;
-	reg_ser_rw_xoff xoff;
-	reg_ser_rw_xoff_clr xoff_clr = {0};
-	reg_ser_rw_tr_ctrl tx_ctrl = {0};
-	reg_ser_rw_tr_dma_en tx_dma_en = {0};
-	reg_ser_rw_rec_ctrl rx_ctrl = {0};
-	reg_ser_rw_tr_baud_div tx_baud_div = {0};
-	reg_ser_rw_rec_baud_div rx_baud_div = {0};
-	int baud;
-
-	if (old &&
-	    termios->c_cflag == old->c_cflag &&
-	    termios->c_iflag == old->c_iflag)
-		return;
-
-	/* Tx: 8 bit, no/even parity, 1 stop bit, no cts. */
-	tx_ctrl.base_freq = regk_ser_f29_493;
-	tx_ctrl.en = 0;
-	tx_ctrl.stop = 0;
-	tx_ctrl.auto_rts = regk_ser_no;
-	tx_ctrl.txd = 1;
-	tx_ctrl.auto_cts = 0;
-	/* Rx: 8 bit, no/even parity. */
-	rx_ctrl.dma_err = regk_ser_stop;
-	rx_ctrl.sampling = regk_ser_majority;
-	rx_ctrl.timeout = 1;
-
-	rx_ctrl.rts_n = regk_ser_inactive;
-
-	/* Common for tx and rx: 8N1. */
-	tx_ctrl.data_bits = regk_ser_bits8;
-	rx_ctrl.data_bits = regk_ser_bits8;
-	tx_ctrl.par = regk_ser_even;
-	rx_ctrl.par = regk_ser_even;
-	tx_ctrl.par_en = regk_ser_no;
-	rx_ctrl.par_en = regk_ser_no;
-
-	tx_ctrl.stop_bits = regk_ser_bits1;
-
-	/*
-	 * Change baud-rate and write it to the hardware.
-	 *
-	 * baud_clock = base_freq / (divisor*8)
-	 * divisor = base_freq / (baud_clock * 8)
-	 * base_freq is either:
-	 * off, ext, 29.493MHz, 32.000 MHz, 32.768 MHz or 100 MHz
-	 * 20.493MHz is used for standard baudrates
-	 */
-
-	/*
-	 * For the console port we keep the original baudrate here.  Not very
-	 * beautiful.
-	 */
-	if ((port != console_port) || old)
-		baud = uart_get_baud_rate(port, termios, old, 0,
-					  port->uartclk / 8);
-	else
-		baud = console_baud;
-
-	tx_baud_div.div = 29493000 / (8 * baud);
-	/* Rx uses same as tx. */
-	rx_baud_div.div = tx_baud_div.div;
-	rx_ctrl.base_freq = tx_ctrl.base_freq;
-
-	if ((termios->c_cflag & CSIZE) == CS7) {
-		/* Set 7 bit mode. */
-		tx_ctrl.data_bits = regk_ser_bits7;
-		rx_ctrl.data_bits = regk_ser_bits7;
-	}
-
-	if (termios->c_cflag & CSTOPB) {
-		/* Set 2 stop bit mode. */
-		tx_ctrl.stop_bits = regk_ser_bits2;
-	}
-
-	if (termios->c_cflag & PARENB) {
-		/* Enable parity. */
-		tx_ctrl.par_en = regk_ser_yes;
-		rx_ctrl.par_en = regk_ser_yes;
-	}
-
-	if (termios->c_cflag & CMSPAR) {
-		if (termios->c_cflag & PARODD) {
-			/* Set mark parity if PARODD and CMSPAR. */
-			tx_ctrl.par = regk_ser_mark;
-			rx_ctrl.par = regk_ser_mark;
-		} else {
-			tx_ctrl.par = regk_ser_space;
-			rx_ctrl.par = regk_ser_space;
-		}
-	} else {
-		if (termios->c_cflag & PARODD) {
-			/* Set odd parity. */
-		       tx_ctrl.par = regk_ser_odd;
-		       rx_ctrl.par = regk_ser_odd;
-		}
-	}
-
-	if (termios->c_cflag & CRTSCTS) {
-		/* Enable automatic CTS handling. */
-		tx_ctrl.auto_cts = regk_ser_yes;
-	}
-
-	/* Make sure the tx and rx are enabled. */
-	tx_ctrl.en = regk_ser_yes;
-	rx_ctrl.en = regk_ser_yes;
-
-	spin_lock_irqsave(&port->lock, flags);
-
-	tx_dma_en.en = 0;
-	REG_WR(ser, up->regi_ser, rw_tr_dma_en, tx_dma_en);
-
-	/* Actually write the control regs (if modified) to the hardware. */
-	uart_update_timeout(port, termios->c_cflag, port->uartclk/8);
-	MODIFY_REG(up->regi_ser, rw_rec_baud_div, rx_baud_div);
-	MODIFY_REG(up->regi_ser, rw_rec_ctrl, rx_ctrl);
-
-	MODIFY_REG(up->regi_ser, rw_tr_baud_div, tx_baud_div);
-	MODIFY_REG(up->regi_ser, rw_tr_ctrl, tx_ctrl);
-
-	tx_dma_en.en = 0;
-	REG_WR(ser, up->regi_ser, rw_tr_dma_en, tx_dma_en);
-
-	xoff = REG_RD(ser, up->regi_ser, rw_xoff);
-
-	if (up->port.state && up->port.state->port.tty &&
-	    (up->port.state->port.tty->termios.c_iflag & IXON)) {
-		xoff.chr = STOP_CHAR(up->port.state->port.tty);
-		xoff.automatic = regk_ser_yes;
-	} else
-		xoff.automatic = regk_ser_no;
-
-	MODIFY_REG(up->regi_ser, rw_xoff, xoff);
-
-	/*
-	 * Make sure we don't start in an automatically shut-off state due to
-	 * a previous early exit.
-	 */
-	xoff_clr.clr = 1;
-	REG_WR(ser, up->regi_ser, rw_xoff_clr, xoff_clr);
-
-	etraxfs_uart_set_mctrl(&up->port, up->port.mctrl);
-	spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static const char *
-etraxfs_uart_type(struct uart_port *port)
-{
-	return "CRISv32";
-}
-
-static void etraxfs_uart_release_port(struct uart_port *port)
-{
-}
-
-static int etraxfs_uart_request_port(struct uart_port *port)
-{
-	return 0;
-}
-
-static void etraxfs_uart_config_port(struct uart_port *port, int flags)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	up->port.type = PORT_CRIS;
-}
-
-static const struct uart_ops etraxfs_uart_pops = {
-	.tx_empty = etraxfs_uart_tx_empty,
-	.set_mctrl = etraxfs_uart_set_mctrl,
-	.get_mctrl = etraxfs_uart_get_mctrl,
-	.stop_tx = etraxfs_uart_stop_tx,
-	.start_tx = etraxfs_uart_start_tx,
-	.send_xchar = etraxfs_uart_send_xchar,
-	.stop_rx = etraxfs_uart_stop_rx,
-	.break_ctl = etraxfs_uart_break_ctl,
-	.startup = etraxfs_uart_startup,
-	.shutdown = etraxfs_uart_shutdown,
-	.set_termios = etraxfs_uart_set_termios,
-	.type = etraxfs_uart_type,
-	.release_port = etraxfs_uart_release_port,
-	.request_port = etraxfs_uart_request_port,
-	.config_port = etraxfs_uart_config_port,
-#ifdef CONFIG_CONSOLE_POLL
-	.poll_get_char = etraxfs_uart_get_poll_char,
-	.poll_put_char = etraxfs_uart_put_poll_char,
-#endif
-};
-
-static void cris_serial_port_init(struct uart_port *port, int line)
-{
-	struct uart_cris_port *up = (struct uart_cris_port *)port;
-
-	if (up->initialized)
-		return;
-	up->initialized = 1;
-	port->line = line;
-	spin_lock_init(&port->lock);
-	port->ops = &etraxfs_uart_pops;
-	port->irq = up->irq;
-	port->iobase = (unsigned long) up->regi_ser;
-	port->uartclk = 29493000;
-
-	/*
-	 * We can't fit any more than 255 here (unsigned char), though
-	 * actually UART_XMIT_SIZE characters could be pending output.
-	 * At time of this writing, the definition of "fifosize" is here the
-	 * amount of characters that can be pending output after a start_tx call
-	 * until tx_empty returns 1: see serial_core.c:uart_wait_until_sent.
-	 * This matters for timeout calculations unfortunately, but keeping
-	 * larger amounts at the DMA wouldn't win much so let's just play nice.
-	 */
-	port->fifosize = 255;
-	port->flags = UPF_BOOT_AUTOCONF;
-}
-
-static int etraxfs_uart_probe(struct platform_device *pdev)
-{
-	struct device_node *np = pdev->dev.of_node;
-	struct uart_cris_port *up;
-	int dev_id;
-
-	if (!np)
-		return -ENODEV;
-
-	dev_id = of_alias_get_id(np, "serial");
-	if (dev_id < 0)
-		dev_id = 0;
-
-	if (dev_id >= UART_NR)
-		return -EINVAL;
-
-	if (etraxfs_uart_ports[dev_id])
-		return -EBUSY;
-
-	up = devm_kzalloc(&pdev->dev, sizeof(struct uart_cris_port),
-			  GFP_KERNEL);
-	if (!up)
-		return -ENOMEM;
-
-	up->irq = irq_of_parse_and_map(np, 0);
-	up->regi_ser = of_iomap(np, 0);
-	up->port.dev = &pdev->dev;
-
-	up->gpios = mctrl_gpio_init_noauto(&pdev->dev, 0);
-	if (IS_ERR(up->gpios))
-		return PTR_ERR(up->gpios);
-
-	cris_serial_port_init(&up->port, dev_id);
-
-	etraxfs_uart_ports[dev_id] = up;
-	platform_set_drvdata(pdev, &up->port);
-	uart_add_one_port(&etraxfs_uart_driver, &up->port);
-
-	return 0;
-}
-
-static int etraxfs_uart_remove(struct platform_device *pdev)
-{
-	struct uart_port *port;
-
-	port = platform_get_drvdata(pdev);
-	uart_remove_one_port(&etraxfs_uart_driver, port);
-	etraxfs_uart_ports[port->line] = NULL;
-
-	return 0;
-}
-
-static const struct of_device_id etraxfs_uart_dt_ids[] = {
-	{ .compatible = "axis,etraxfs-uart" },
-	{ /* sentinel */ }
-};
-
-MODULE_DEVICE_TABLE(of, etraxfs_uart_dt_ids);
-
-static struct platform_driver etraxfs_uart_platform_driver = {
-	.driver = {
-		.name   = DRV_NAME,
-		.of_match_table	= of_match_ptr(etraxfs_uart_dt_ids),
-	},
-	.probe          = etraxfs_uart_probe,
-	.remove         = etraxfs_uart_remove,
-};
-
-static int __init etraxfs_uart_init(void)
-{
-	int ret;
-
-	ret = uart_register_driver(&etraxfs_uart_driver);
-	if (ret)
-		return ret;
-
-	ret = platform_driver_register(&etraxfs_uart_platform_driver);
-	if (ret)
-		uart_unregister_driver(&etraxfs_uart_driver);
-
-	return ret;
-}
-
-static void __exit etraxfs_uart_exit(void)
-{
-	platform_driver_unregister(&etraxfs_uart_platform_driver);
-	uart_unregister_driver(&etraxfs_uart_driver);
-}
-
-module_init(etraxfs_uart_init);
-module_exit(etraxfs_uart_exit);