summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorakshatzen <akshatzen@google.com>2021-01-09 18:08:44 +0530
committerMartin K. Petersen <martin.petersen@oracle.com>2021-01-13 00:02:01 -0500
commit95652f98b1daf0c483932ee70ae00a526f205aa9 (patch)
treeeb5722e629502f10f758e80134e949e648602a5d
parenta961ea0afd632cc570b71e455fe4328ee2fd9348 (diff)
scsi: pm80xx: Check main config table address
The driver initializes main configuration, general status, inbound queue and outbound queue table addresses based on a value read from MSGU_SCRATCH_PAD_0 register. We should validate these addresses before dereferencing them. Adds two validations: 1. Check if main configuration table offset lies within the pcibar mapped 2. Check if first dword of main configuration table reads "PMCS" There are two calls to init_pci_device_addresses() done during pm8001_pci_probe() in this sequence: 1. First inside chip_soft_rst, where if init_pci_device_addresses fails we will go ahead assuming MPI state is not ready and reset the device as long as bootloader is okay. This gives chance to second call of init_pci_device_addresses to set up the addresses after reset. 2. The second call is via pm80xx_chip_init, after soft reset is done and firmware is checked to be ready. Once that is done we are safe to go ahead and initialize default table values and use them. Tests: 1. Enabled debugging logs and observed no issues during initialization, with a controller with no issues: pm80xx0:: pm8001_setup_msix 1034: pci_alloc_irq_vectors request ret:64 no of intr 64 pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000 pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0 pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50 pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4 pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128 pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928 pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408 pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608 pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval) pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval) pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval) pm80xx0:: pm80xx_chip_soft_rst 1446: reset register before write : 0x0 pm80xx0:: pm80xx_chip_soft_rst 1478: reset register after write 0x40 pm80xx0:: pm80xx_chip_soft_rst 1544: SPCv soft reset Complete pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000 pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0 pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50 pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4 pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128 pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928 pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408 pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608 pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval) pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval) pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval) pm80xx0:: pm80xx_chip_init 1329: MPI initialize successful! 2. Tested controller with firmware known to have initialization issue and observed no crashes with this fix: pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38 pm80xx 0000:01:00.0: Removing from 1:1 domain pm80xx 0000:01:00.0: Requesting non-1:1 mappings pm80xx0:: init_pci_device_addresses 948: BAD main config signature 0x0 pm80xx0:: mpi_uninit_check 1365: Failed to init pci addresses pm80xx0:: pm80xx_chip_soft_rst 1435: MPI state is not ready scratch:0:8:62a01000:0 pm80xx0:: pm80xx_chip_soft_rst 1518: Firmware is not ready! pm80xx0:: pm80xx_chip_soft_rst 1532: iButton Feature is not Available!!! pm80xx0:: pm80xx_chip_init 1301: Firmware is not ready! pm80xx0:: pm8001_pci_probe 1215: chip_init failed [ret: -16] pm80xx: probe of 0000:01:00.0 failed with error -16 pm80xx 0000:07:00.0: pm80xx: driver version 0.1.38 pm80xx 0000:07:00.0: Removing from 1:1 domain pm80xx 0000:07:00.0: Requesting non-1:1 mappings scsi host6: pm80xx pm80xx1:: pm8001_setup_sgpio 5568: failed sgpio_req timeout pm80xx1:: mpi_phy_start_resp 3447: phy start resp status:0x0, phyid:0x0 pm80xx 0000:08:00.0: pm80xx: driver version 0.1.38 pm80xx 0000:08:00.0: Removing from 1:1 domain pm80xx 0000:08:00.0: Requesting non-1:1 mappings 3. Without this fix we observe crash on the same controller: pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38 pm80xx 0000:01:00.0: Removing from 1:1 domain pm80xx 0000:01:00.0: Requesting non-1:1 mappings [<ffffffffc0451b3b>] pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx] [<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx] RIP: 0010:pm80xx_chip_soft_rst+0x71/0x4c0 [pm80xx] [<ffffffffc0451b3b>] ? pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx] [<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx] pm80xx0:: mpi_uninit_check 1339: TIMEOUT:IBDB value/=2 pm80xx0:: pm80xx_chip_soft_rst 1387: MPI state is not ready scratch:0:8:62a01000:0 pm80xx0:: pm80xx_chip_soft_rst 1470: Firmware is not ready! pm80xx0:: pm80xx_chip_soft_rst 1484: iButton Feature is not Available!!! pm80xx0:: pm80xx_chip_init 1266: Firmware is not ready! pm80xx0:: pm8001_pci_probe 1207: chip_init failed [ret: -16] pm80xx: probe of 0000:01:00.0 failed with error -16 Link: https://lore.kernel.org/r/20210109123849.17098-4-Viswas.G@microchip.com Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: akshatzen <akshatzen@google.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com> Signed-off-by: Radha Ramachandran <radha@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-rw-r--r--drivers/scsi/pm8001/pm8001_init.c11
-rw-r--r--drivers/scsi/pm8001/pm80xx_hwi.c53
2 files changed, 58 insertions, 6 deletions
diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
index ee2de177d0d0..d21078ca7fb3 100644
--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -466,9 +466,12 @@ static int pm8001_ioremap(struct pm8001_hba_info *pm8001_ha)
pm8001_ha->io_mem[logicalBar].memvirtaddr =
ioremap(pm8001_ha->io_mem[logicalBar].membase,
pm8001_ha->io_mem[logicalBar].memsize);
- pm8001_dbg(pm8001_ha, INIT,
- "PCI: bar %d, logicalBar %d\n",
+ if (!pm8001_ha->io_mem[logicalBar].memvirtaddr) {
+ pm8001_dbg(pm8001_ha, INIT,
+ "Failed to ioremap bar %d, logicalBar %d",
bar, logicalBar);
+ return -ENOMEM;
+ }
pm8001_dbg(pm8001_ha, INIT,
"base addr %llx virt_addr=%llx len=%d\n",
(u64)pm8001_ha->io_mem[logicalBar].membase,
@@ -540,9 +543,11 @@ static struct pm8001_hba_info *pm8001_pci_alloc(struct pci_dev *pdev,
tasklet_init(&pm8001_ha->tasklet[j], pm8001_tasklet,
(unsigned long)&(pm8001_ha->irq_vector[j]));
#endif
- pm8001_ioremap(pm8001_ha);
+ if (pm8001_ioremap(pm8001_ha))
+ goto failed_pci_alloc;
if (!pm8001_alloc(pm8001_ha, ent))
return pm8001_ha;
+failed_pci_alloc:
pm8001_free(pm8001_ha);
return NULL;
}
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c
index 86a3d483749c..7d0eada11d3c 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -1115,7 +1115,7 @@ static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
return ret;
}
-static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
+static int init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *base_addr;
u32 value;
@@ -1124,15 +1124,48 @@ static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
u32 pcilogic;
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
+
+ /**
+ * lower 26 bits of SCRATCHPAD0 register describes offset within the
+ * PCIe BAR where the MPI configuration table is present
+ */
offset = value & 0x03FFFFFF; /* scratch pad 0 TBL address */
pm8001_dbg(pm8001_ha, DEV, "Scratchpad 0 Offset: 0x%x value 0x%x\n",
offset, value);
+ /**
+ * Upper 6 bits describe the offset within PCI config space where BAR
+ * is located.
+ */
pcilogic = (value & 0xFC000000) >> 26;
pcibar = get_pci_bar_index(pcilogic);
pm8001_dbg(pm8001_ha, INIT, "Scratchpad 0 PCI BAR: %d\n", pcibar);
+
+ /**
+ * Make sure the offset falls inside the ioremapped PCI BAR
+ */
+ if (offset > pm8001_ha->io_mem[pcibar].memsize) {
+ pm8001_dbg(pm8001_ha, FAIL,
+ "Main cfg tbl offset outside %u > %u\n",
+ offset, pm8001_ha->io_mem[pcibar].memsize);
+ return -EBUSY;
+ }
pm8001_ha->main_cfg_tbl_addr = base_addr =
pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
+
+ /**
+ * Validate main configuration table address: first DWord should read
+ * "PMCS"
+ */
+ value = pm8001_mr32(pm8001_ha->main_cfg_tbl_addr, 0);
+ if (memcmp(&value, "PMCS", 4) != 0) {
+ pm8001_dbg(pm8001_ha, FAIL,
+ "BAD main config signature 0x%x\n",
+ value);
+ return -EBUSY;
+ }
+ pm8001_dbg(pm8001_ha, INIT,
+ "VALID main config signature 0x%x\n", value);
pm8001_ha->general_stat_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x18) &
0xFFFFFF);
@@ -1171,6 +1204,7 @@ static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
pm8001_dbg(pm8001_ha, INIT, "addr - pspa %p ivt %p\n",
pm8001_ha->pspa_q_tbl_addr,
pm8001_ha->ivt_tbl_addr);
+ return 0;
}
/**
@@ -1438,7 +1472,12 @@ static int pm80xx_chip_init(struct pm8001_hba_info *pm8001_ha)
pm8001_ha->controller_fatal_error = false;
/* Initialize pci space address eg: mpi offset */
- init_pci_device_addresses(pm8001_ha);
+ ret = init_pci_device_addresses(pm8001_ha);
+ if (ret) {
+ pm8001_dbg(pm8001_ha, FAIL,
+ "Failed to init pci addresses");
+ return ret;
+ }
init_default_table_values(pm8001_ha);
read_main_config_table(pm8001_ha);
read_general_status_table(pm8001_ha);
@@ -1482,7 +1521,15 @@ static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
- init_pci_device_addresses(pm8001_ha);
+ int ret;
+
+ ret = init_pci_device_addresses(pm8001_ha);
+ if (ret) {
+ pm8001_dbg(pm8001_ha, FAIL,
+ "Failed to init pci addresses");
+ return ret;
+ }
+
/* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
table is stop */
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPCv_MSGU_CFG_TABLE_RESET);